AlphaLISA Albumin (Human) Biotin-Free Detection Kit

Transcription

1 TECHNICAL DATA SHEET AlphaLISA Research Reagents AlphaLISA Albumin (Human) Biotin-Free Detection Kit Product number: AL363HV/C/F Caution: For Laboratory Use. A research product for research purposes only. Contents Product Information.2 Page Quality Control..2 Analyte of Interest Description of the AlphaLISA Assay...3 Precautions 3 Kit content: Reagents and Materials.. 4 Recommendations....5 Assay Procedure Data Analysis... 8 Assay Performance Characteristics...9 Troubleshooting Guide...11

2 2 Product Information Application: Sensitivity: This kit is designed for the quantitative determination of Human Albumin in cell culture supernatants using a homogeneous AlphaLISA assay (no wash steps). The kit utilizes a Digoxigenin (DIG)/ Anti-DIG interaction as opposed to the traditional Streptavidin/Biotin interaction. This enables optimal performance when working with biotin-rich media (e.g. RPMI) or samples containing endogenous biotin (e.g. milk, brain extracts). Lower Detection Limit (LDL): 102 pg/ml Lower Limit of Quantification (LLOQ): 346 pg/ml EC 50 : 176 ng/ml Dynamic range: pg/ml (Figure 1). Figure1. Typical sensitivity curves in AlphaLISA NaCl Buffer. The data was generated using a white Optiplate TM -384 microplate and the EnVision Multilabel Plate Reader with Alpha option Storage: Stability: Store kit in the dark at +4 C. Store reconstituted analyte at -20 C. This product is stable for at least 6 months from the manufacturing date when stored in its original packaging and the recommended storage conditions. Note: Once reconstituted, the human Albumin analyte is stable for at least 75 days at -20 C. Quality Control Lot to lot consistency is confirmed in an AlphaLISA assay. Maximum and minimum signals, EC 50 and LDL were measured on the EnVision Multilabel Plate Reader with Alpha option using the protocol described in this technical data sheet. We certify that these results meet our quality release criteria. Maximum counts may vary between bead lots and the instrument used, with no impact on LDL measurement. 2

3 3 Analyte of Interest Human serum albumin (HSA) is a 66 kda protein produced by the liver. HSA constitutes two thirds of the protein mass of serum and plays a key role in the transport of small molecules in the blood such as fatty acids, vitamins, hormones, divalent cations, and drugs. Another important function of HSA is to maintain osmotic pressure and ph in the blood. HSA is an important biomarker in kidney disease. In albuminuria, albumin is not reabsorbed properly by kidney glomeruli and is excreted in the urine. Generally, in hypoalbuminemia, a lower level of albumin in serum can be explained by a kidney disease, poor liver function, or inflammation. Description of the AlphaLISA Assay AlphaLISA technology allows the detection of molecules of interest in buffer, cell culture media, serum and plasma in a highly sensitive, quantitative, reproducible and user-friendly mode. In this AlphaLISA assay, a DIG-labeled Anti-Analyte Antibody binds to the anti-dig Alpha Donor beads, while another Anti-Analyte Antibody is conjugated to AlphaLISA Acceptor beads. In the presence of the analyte, the beads come into close proximity. The excitation of the Donor beads provokes the release of singlet oxygen molecules that triggers a cascade of energy transfer in the Acceptor beads,resulting in a sharp peak of light emission at 615 nm (Figure 2). Figure 2. AlphaLISA Assay principle. Precautions Anti-Digoxigenin Fab Fragment Donor beads are light-sensitive. All the other assay reagents can be used under normal light conditions. All Alpha assays using the Donor beads should be performed under subdued laboratory lighting (< 100 lux). Green filters (LEE 090 filters (preferred) or Roscolux filters #389 from Rosco) can be applied to light fixtures. All blood components and biological materials should be handled as potentially hazardous. The analyte included in this kit is from a Mouse source. Some analytes are present in saliva. Take precautionary measures to avoid contamination of the reagent solutions. The DIG labeled anti-analyte antibody is toxic. Contact with skin or inhalation should be avoided. 3

4 4 Kit Content: Reagents and Materials Kit components AL363HV (100 assay points***) AL363C (500 assay points***) AL363F (5000 assay points***) AlphaLISA Anti-Albumin Acceptor beads stored in PBS, 0.05% Proclin- 300, ph mg/ml (1 brown tube, white cap) 50 5 mg/ml (1 brown tube, white cap) mg/ml (1 brown tube, white cap) Anti-Digoxigenin Fab Fragment Donor beads stored in 25 mm HEPES, 100 mm NaCl, 0.05% Proclin-300, ph mg/ml (1 brown tube, black cap) mg/ml (1 brown tube, black cap) 2 x 1 5 mg/ml (2 brown tubes, black caps) DIG labeled Anti-Albumin stored in PBS, 0.1% Tween-20, 0.05% NaN 3, ph nm (1 tube, black cap) nm (1 tube, black cap) nm (1 tube, black cap) AlphaLISA Albumin (1 µg), lyophilized Analyte* 1 µg 1 tube, clear cap 1 µg 1 tube, clear cap 1 µg 1 tube, clear cap AlphaLISA NaCl Buffer (5X)** 2 ml, 1 small bottle 10 ml, 1 small bottle 100 ml, 1 large bottle * Reconstitute human Albumin in 100 µl Milli-Q grade H 2 O. The reconstituted analyte should be used within 60 minutes or aliquoted into screw-capped polypropylene vials and stored at 4C for further experiments. Avoid multiple freeze-thaw cycles. It has been demonstrated that reconstituted human Albumin is stable for at least 75 days at - 20 C.One vial contains an amount of human Albumin sufficient for performing 10 standard curves. Additional vials can be ordered separately (cat # AL294S). ** Contains 125 mm HEPES, ph 7.4, 2.5 M NaCl, 5 mg/ml Dextran-500, 2.5% Triton X-100, 0.25% Proclin-300, 2.5% gelatin. Extra buffer can be ordered separately (cat # AL007C: 10 ml, cat # AL007F: 100 ml). Note: 5X buffer might be slightly yellow. However, this does not affect the assay results. Once diluted, 1X AlphaLISA NaCl Buffer contains 25 mm HEPES, ph 7.4, 0.5 M NaCl, 1 mg/ml Dextran-500, 0.5% Triton X-100, 0.05% Proclin-300 and 0.5% gelatin. *** The number of assay points is based on an assay volume of 100 µl in 96-well plates or 50 µl in 96- or 384-well assay plates using the kit components at the recommended concentrations. Sodium azide should not be added to the stock reagents. High concentrations of sodium azide (> % final in the assay) might decrease the AlphaLISA signal. Specific additional required reagents and materials: The following materials are recommended: Item Suggested source Catalog # TopSeal -A Plus Adhesive Sealing Film PerkinElmer Inc EnVision -Alpha Reader PerkinElmer Inc. - 4

5 5 Recommendations The volume indicated on each tube is guaranteed for single pipetting. Multiple pipetting of the reagents may reduce the theoretical amount left in the tube. To minimize loss when pipetting beads, it is preferable not to pre-wet the tip. Centrifuge all tubes (including lyophilized analyte) before use to improve recovery of content (2000g, sec). Re-suspend all reagents by vortexing before use. Use Milli-Q grade H 2 O (18 MΩ cm) to dilute 5X AlphaLISA NaCl Buffer and to reconstitute the lyophilized analyte. When diluting the standard or samples, change tips between each standard or sample dilution. When loading reagents in the assay microplate, change tips between each standard or sample addition and after each set of reagents. When reagents are added to the microplate, make sure the liquids are at the bottom of the well. Small volumes may be prone to evaporation. It is recommended to cover microplates with TopSeal-A Adhesive Sealing Films to reduce evaporation during incubation. Microplates can be read with the TopSeal-A Film. The AlphaLISA signal is detected with an EnVision Multilabel Reader equipped with the Alpha option using the AlphaScreen standard settings (e.g. Total Measurement Time: 550 ms, Laser 680 nm Excitation Time: 180 ms, Mirror: D640as, Emission Filter: M570w, Center Wavelength 570 nm, Bandwidth 100 nm, Transmittance 75%). AlphaLISA signal will vary with temperature and incubation time. For consistent results, identical incubation times and temperature should be used for each plate. The standard curves shown in this technical data sheet are provided for information only. A standard curve must be generated for each experiment. The standard curve should be performed in the Immunoassay buffer for serum and/or plasma samples. Assay Procedure IMPORTANT: PLEASE READ THE RECOMMENDATIONS BELOW BEFORE USE The protocol described below is an example for generating one standard curve in a 50 µl final assay volume (48 wells, triplicate determinations). The protocols also include testing samples in 452 wells. If a different amount of samples are tested, the volumes of all reagents have to be adjusted accordingly, as shown in the table below. These calculations do not include excess reagent to account for losses during transfer of solutions or dead volumes. The standard dilution protocol is provided for information only. As needed, the number of replicates or the range of concentrations covered can be modified. Use of four background points in triplicate (12 wells) is recommended when LDL/LLOQ is calculated. One background point in triplicate (3 wells) can be used when LDL/LLOQ is not calculated. 5

6 6 Volume Format # of data points Final Sample AlphaLISA beads / Anti-DIG Antibody MIX Donor beads AL363HV µl 10 µl 10 µl 80 µl Plate recommendation White OptiPlate-96 (cat # ) White ½ AreaPlate-96 (cat # ) AL363C AL363F µl 10 µl 10 µl 80 µl µl 5 µl 5 µl 40 µl µl 2 µl 2 µl 16 µl µl 1 µl 1 µl 8 µl µl 5 µl 5 µl 40 µl µl 2 µl 2 µl 16 µl µl 1 µl 1 µl 8 µl White OptiPlate-96 (cat # ) White ½ AreaPlate-96 (cat # ) White ½ AreaPlate-96 (cat # ) White OptiPlate-384 (cat # ) Light gray AlphaPlate -384 (cat # ) Light gray AlphaPlate-384 (cat # ) ProxiPlate -384 Plus (cat # ) White OptiPlate-384 (cat # ) Light gray AlphaPlate-1536 (cat # ) White ½ AreaPlate-96 (cat # ) White OptiPlate-384 (cat # ) Light gray AlphaPlate-384 (cat # ) Light gray AlphaPlate-384 (cat # ) ProxiPlate-384 Plus (cat # ) White OptiPlate-384 (cat # ) Light gray AlphaPlate-1536 (cat # ) 6

7 7 High Concentration 2 step protocol - The protocol described below is for 500 assay points including one standard curve (48 wells) and samples (452 wells). If a different amount of samples are tested, the volumes of all reagents have to be adjusted accordingly. 1) Preparation of 1X AlphaLISA NaCl Buffer: Add 8 ml of 5X AlphaLISA NaCl Buffer to 32 ml H 2 O. 2) Preparation of Albumin analyte standard dilutions: a) Reconstitute lyophilized Albumin (1 µg) in 100 µl of H 2 O. b) Prepare standard dilutions as follows in 1X AlphaLISA NaCl Buffer (change tip between each standard dilution): Tube Vol. of Vol. of [Albumin] in standard curve diluent Albumin(µL) (µl) * (g/ml in 5 µl) (pg/ml in 5 µl) A 10 µl of reconstituted Albumin E B 60 µl of tube A E C 60 µl of tube B E D 60 µl of tube C E E 60 µl of tube D E F 60 µl of tube E E G 60 µl of tube F E H 60 µl of tube G E I 60 µl of tube H E J 60 µl of tube I E K 60 µl of tube J E L 60 µl of tube K E-12 3 M ** (background) N ** (background) O ** (background) P ** (background) * Dilute standards in diluent (e.g. 1X AlphaLISA NaCl Buffer). At low concentrations of analyte, a significant amount of analyte can bind to the vial. Therefore, load the analyte standard dilutions in the assay microplate within 60 minutes of preparation. ** Four background points in triplicate (12 wells) are used when LDL is calculated. If LDL does not need to be calculated, one background point in triplicate can be used (3 wells). 3) Preparation of 10X MIX AlphaLISA Anti-Albumin Acceptor beads (100 µg/ml) + DIG labeled Anti-Albumin Antibody (10 nm): a. Add 50 µl of 5 mg/ml AlphaLISA Anti-Albumin Acceptor beads and 50 μl of 500 nm Anti-Albumin Antibody to 2400 µl of 1X AlphaLISA NaCl Buffer. b. Prepare just before use 4) Preparation of 1.25X Anti-Digoxigenin Fab Fragment Donor beads (50 µg/ml): a. Keep the beads under subdued laboratory lighting. b. Add 200 µl of 5 mg/ml Anti-Digoxigenin Fab Fragment Donor beads to µl of 1X AlphaLISA NaCl Buffer. c. Prepare just before use. 7

8 8 5) In a white Optiplate (384 wells): Add 5 µl of each analyte standard dilution Add 5 µl of a 10X MIX AlphaLISA Anti-Analyte Acceptor beads (10 µg/ml final) + DIG labeled Anti-Albumin antibody (1 nm final) Incubate 60 minutes at 23 C Add 40 µl of 1.25X Anti-Digoxigenin Fab Fragment Donor beads (40 µg/ml final) Incubate 60 minutes at 23 C in the dark Read using EnVision-Alpha Reader 615 nm Data Analysis Calculate the average count value for the background wells. Generate a standard curve by plotting the AlphaLISA counts versus the concentration of analyte. A log scale can be used for either or both axes. No additional data transformation is required. Analyze data according to a nonlinear regression using the 4-parameter logistic equation (sigmoidal dose-response curve with variable slope) and a 1/Y 2 data weighting (the values at maximal concentrations of analyte after the hook point should be removed for correct analysis). The LDL is calculated by interpolating the average background counts (12 wells without analyte) + 3x standard deviation value (average background counts + (3xSD)) on the standard curve. The LLOQ as measured here is calculated by interpolating the average background counts (12 wells without analyte) + 10 x standard deviation value (average background counts + (10xSD)) on the standard curve. Alternatively, the true LLOQ can be determined by spiking known concentrations of analyte in the matrix and measuring the percent recovery, and then determining the minimal amount of spiked analyte that can be quantified within a given limit (usually +/- 20% or 30% of the real concentration). Read from the standard curve the concentration of analyte contained in the samples. If samples have been diluted, the concentration read from the standard curve must be multiplied by the dilution factor. 8

9 AlphaLISA Signal (Counts) 9 Assay Performance Characteristics AlphaLISA assay performance described below was determined using the High Concentration 2 step protocol. Assay Sensitivity: The LDL was calculated as described in the data analysis section. The values correspond to the lowest concentration of analyte that can be detected using the recommended assay conditions. LDL (pg/ml) Buffer/Media # of experiments 102 AlphaLISA NaCl Buffer RPMI with 10% FBS AlphaLISA NaCl Buffer RPMI+10%FBS Log [halbumin], (g/ml) * Note that LDL can be decreased (i.e. sensitivity increased) by increasing the volume of analyte in the assay (e.g. use 10 µl of analyte in a final assay volume of 50 µl). Assay Precision: The following assay precision data were calculated from the three independent assays using two different kit lots. In each lot, the analytes were prepared in AlphaLISA NaCl Buffer, or RPMI. Each assay consisted of one standard curve comprising 12 data points (each in triplicate) and 12 background wells (no analytes). The assays were performed in 384- well format using AlphaLISA NaCl Buffer. Intra-assay precision: The intra-assay precision was determined using 3 independent experiments for a total of 16 independent determinations in triplicate. CV% were calculated for each individual experiment then averaged. Shown is the average intra-experimental CV%. Albumin AlphaLISA NaCl Buffer RPMI CV% 6% 5% 9

10 10 Inter-assay precision: The inter-assay precision was determined using the data across 3 independent experiments with 16 measurements in triplicate. CV% was calculated by comparing the same measurement in each experiment. The CV% for all 16 measurements was then averaged. Shown is the inter-experimental CV%. Albumin AlphaLISA NaCl Buffer RPMI CV% 15% 13% Spike Recovery: Four known concentrations of analyte were spiked in AlphaLISA NaCl Buffer and cell culture media supplemented with 10% FBS. The spiked samples were referenced to the analyte curve produced in AlphaLISA Immunoassay Buffer and culture media. Spiked Albumin (ng/ml) AlphaLISA NaCl Buffer % Recovery RPMI

11 11 Troubleshooting Guide You will find detailed recommendations for common situations you might encounter with your AlphaLISA Assay kit at: FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. This product is not for resale or distribution except by authorized distributors. LIMITED WARRANTY: PerkinElmer BioSignal Inc. warrants that, at the time of shipment, the products sold by it are free from defects in material and workmanship and conform to specifications which accompany the product. PerkinElmer BioSignal Inc. makes no other warranty, express or implied with respect to the products, including any warranty of merchantability or fitness for any particular purpose. Notification of any breach of warranty must be made within 60 days of receipt unless otherwise provided in writing by PerkinElmer BioSignal Inc. No claim shall be honored if the customer fails to notify PerkinElmer BioSignal Inc. within the period specified. The sole and exclusive remedy of the customer for any liability of PerkinElmer BioSignal Inc. of any kind including liability based upon warranty (express or implied whether contained herein or elsewhere), strict liability contract or otherwise is limited to the replacement of the goods or the refunds of the invoice price of goods. PerkinElmer BioSignal Inc. shall not in any case be liable for special, incidental or consequential damages of any kind. PerkinElmer, Inc. 940 Winter Street Waltham, MA USA P: (800) or (+1) For a complete listing of our global offices, visit /ContactUs Copyright 2012, PerkinElmer, Inc. All rights reserved. PerkinElmer is a registered trademark of PerkinElmer, Inc. All other trademarks are the property of their respective owners. 11