INFLUENCE OF ELECTRICALLY CONDUCTIVE ADHESIVE AMOUNT ON SHEAR STRENGTH OF GLUED JOINTS ON FLEXIBLE SUBSTRATES

Size: px
Start display at page:

Download "INFLUENCE OF ELECTRICALLY CONDUCTIVE ADHESIVE AMOUNT ON SHEAR STRENGTH OF GLUED JOINTS ON FLEXIBLE SUBSTRATES"

Transcription

1 INFLUENCE OF ELECTRICALLY CONDUCTIVE ADHESIVE AMOUNT ON SHEAR STRENGTH OF GLUED JOINTS ON FLEXIBLE SUBSTRATES ABSTRACT: Martin Hirman and František Steiner Department of Technologies and Measurement Faculty of Electrical Engineering University of West Bohemia Univerzitni 26, Pilsen, Czech Republic This article deals with the influence of electrically conductive adhesive amount on shear strength of joints glue by EPO-TEK H20S and MG 8331S on two types of flexible substrates (MELINEX ST504, DuPont Pyralux AC). These joints were made by gluing of chip resistors 1206, 0805 and 0603 with two curing profiles for each adhesive and with two different curing technologies. The different thickness of stencils and reductions of the hole in stencils were used for the experiment. These differences have an effect on the amount of conductive adhesives on the samples. Samples were measured after curing process by using shear strength test with the device LabTest The article presents effects of different curing profiles, various flexible substrates and different amounts of the adhesives on the mechanical strength of the joint. Keywords: Electrically conductive adhesive, flexible substrate, shear strength, hot plate 1 INTRODUCTION Soldering is the most common used technology for conductive connection of components with substrates in electronic devices. In the past lead solder alloys were almost only used, but currently the lead solder alloys are prohibited by the European Directive RoHS (Restriction of Hazardous Substances) and WEEE (Waste Electrical and Electronic Equipment). Therefore lead free solder alloys or electrically conductive adhesives are used. The using of these materials has some differences. The lead free solder alloys have usually higher melting point than lead solder alloys and the electrically conductive adhesives have usually lower curing temperature than the melting point of the solder alloys but adhesives are hygroscopic and expensive. These properties are big disadvantages of these materials. A lot of experiments on rigid substrates with electrically conductive adhesives as lead solder replacement were already performed, e. g. [1], [2], [3], [4]. The other current trend is to use flexible and textile substrates in practical applications. Especially conductive adhesives can be used for the interconnection of these substrates. Such substrates can change properties of glued joints. The mechanical shear strength of the joint on flexible substrate can be also different in comparison with the shear strength of the joint on rigid substrate. This is the reason for the testing of electrically conductive adhesives on

2 flexible substrates. Due to the high price of electrically conductive adhesives, the research of influence of electrically conductive adhesive amount on shear strength of glued joints is important. Saving a small amount of adhesive on one joint could reduce the production costs significantly. Cost reduction is the reason for conducting the following experiment. 2 MATERIALS AND PROCEDURES Description of the experiment was creates as a process by using methodology BPMN 2.0 (Business Process Model and Notation). This process is shown in Figure 1. Fig. 1: Description of the experiment. 2.1 Flexible PCB The two different types of flexible substrates were used for the experiment. First type was the flexible printed circuit board DuPont Pyralux AC with copper conductive pattern without the surface finish (hereinafter referred to as FPCB Cu ) with size of each sample 28 mm x 53 mm. Second type was the flexible printed circuit boards MELINEX ST504 with silver conductive pattern DuPont 5064H (hereinafter referred to as FPCB Ag ) with size of each sample 35 mm x 60 mm. On both of them, the conductive pattern for gluing of ten SMD chip components was made on one side of printed circuit boards. Three types of samples for mount components with the size 1206, 0805 and 0603 were made for both substrates. Fig. 2: The sample of flexible printed circuit board with copper (left) and silver (right) conductive pattern.

3 2.2 Components For the experiment SMD chip resistors with the resistance 0 Ω and with the sizes 1206, 0805 and 0603 were used. All contacts of chip resistors were surface finished by tin. Fig. 3: The flexible PCB with placed 1206 (left) and 0805 (right) chip resistors. 2.3 Electrically conductive adhesives The two different electrically conductive adhesives with silver flakes were selected for the experiment. The first adhesive brand name is EPO-TEK H20S and it is produced by the Epoxy technology Inc. The particle size of silver flakes in the adhesive is less than 20 μm and the adhesive has the resistivity 0,0005 Ω cm. The price of this adhesive is approximately 4,85 per gram including VAT. That is equal to 11,61 per cubic centimeter. The adhesive has five recommend curing profiles from 80 C per 90 minutes to 175 C per 45 seconds. The second adhesive brand name is 8331S and it is produced by the M.G. Chemicals Ltd. The adhesive has the resistivity 0,0060 Ω cm and the price of the adhesive is approximately 1,67 per gram including VAT. That is equal to 4,06 per cubic centimeter. The adhesive has four recommend curing profiles from 25 C per 96 hours to 100 C per 50 minutes. The both named adhesives are two-component and can be storage in room temperature. The storing in freezer is not recommended and it can be opportunity for reduce the costs for adhesives cooling of product manufacturers. 2.4 Amount of adhesives The stencil printing was used for applying of the electrically conductive adhesives on flexible printed circuit boards. For the experiment three different volumes of the adhesive were used (see Table 2). Reduction of width and length means that holes in the stencils were reduced about 5% and 20% of width and length due to pads in conductive pattern on flexible PCBs. The pads in pattern are standardized (see Table 1). Tab. 1: Size of the pads in pattern for all components. Size of the component Width 1,44 mm 0,71 mm 0,61 mm Length 1,64 mm 1,32 mm 0,86 mm Tab. 2: The parameters of used stencils and volume of the adhesives for 1206 component. Thickness of stencil 120 μm 120 μm 80 μm Reduction of width and length 5% 20% 20% Volume of adhesive 0,256 mm 3 0,181 mm 3 0,121 mm 3

4 The samples were weight by the analytical balances Kern ALJ and by the analytical laboratory balances Radwag XA 52/2X. The weight of one joint was calculated. 2.5 Curing profiles of adhesives The experiment comparing the shear strength of glued joints with using of different curing profiles was performed in past [5]. In mentioned experiment the best curing profiles for adhesives EPO-TEK H20S and MG 8331S were chosen. The profiles from the datasheets (120 C / 15 minutes and 100 C / 50 minutes) were used. Moreover for several reasons the newly defined profiles (135 C / 15 minutes and 130 C / 30 minutes) were used. The first assumption was that the higher curing temperature can improve mechanical strength of the joint and reduce the time for curing. The second assumption was to use of the adhesives on flexible substrates which usually have maximal allowable temperature under 150 C. From these reasons the temperatures were chosen which are higher but the substrates could endure it. All used profiles are stated in Table 3. Tab. 3: The curing profiles of the electrically conductive adhesives. Substrate Type of adhesive Sample Curing temperature Curing time Curing method A 120 C 15 minutes EPO-TEK H20S B 135 C 15 minutes FPCB Ag C 100 C 50 minutes MG 8331S D 130 C 30 minutes Hot air E 120 C 15 minutes EPO-TEK H20S F 135 C 15 minutes G 100 C 50 minutes FPCB Cu H 130 C 30 minutes MG 8331S I 100 C 50 minutes Hot plate J 130 C 30 minutes The laboratory drying oven Heraeus 5050 was used for curing of the adhesives. The temperature inside the drying oven was measured by special device made at the Department of Technologies and Measurement, see Figure 4. The special device for measuring of temperature was connected to the multimeter METRAHIT from the Gossen Metrawatt Company. This multimeter was connected to the computer and the profiles were recorded by software LabVIEW from National Instruments Company. Fig. 4: Device for measuring of temperature in drying oven. For the first part of the experiment standard curing by hot air were used. For the second part of the experiment special curing named snap curing by hot plate were used. The profiles from both methods of curing were tuned and the final profiles are shown in Figure 5.

5 2.6 Shear strength test Fig. 5: The temperature profiles used for curing of adhesives. The mechanical shear strength of glued joint was measured for each sample. The samples were glued to the rigid PCB before testing because the samples were flexible. The principal of mechanical shear strength test can be shown in Figure 6. The thorn pushes by force on the component until the disruption of the joint and shear off the component from PCB. The shear strength of the joint was not measured directly because surface under load is not known. The maximal force during the test was recorded. The device LabTest was used for recording of force acting on the chip resistor. The settings of the device are as follows: feed rate of shear thorn 20 mm/min, jaws return 200 mm/min, criterion of test end when reaching 70 % of maximal force (F max ). Ten components were measured for each sample and ten values of maximal force were statistically analyzed for each sample. Fig. 6: The device LabTest (upper-left side), the thorn with the sample (upper-right side, lower-left side), principle of shear strength test (lower-right side).

6 3 RESULTS AND DISCUSSION The maximal force to shear off the component from the flexible PCB was recorded when the mechanical shear strength test was performed. The recorded values were statistically analyzed and the results of this analyzes can be seen in Figure 7 9. Fig. 7: Boxplot of maximal force when shearing-off 1206 chip resistors glued on flexible PCB. Fig. 8: Boxplot of maximal force when shearing-off 0805 chip resistors glued on flexible PCB.

7 Fig. 9: Boxplot of maximal force when shearing-off 0603 chip resistors glued on flexible PCB. A full factorial analysis and methodology DOE (Design of Experiments) were used for evaluation of the results (for components 1206 and 0805). This methodology is often used for detection of more and less significant factors, e.g. [6]. The results of this analysis and the influence of each factor on the mechanical shear strength are seen in Figure 10. Fig. 10: Influence of factors on the mechanical shear strength from DOE methodology. The most significant factors are size of the component and type of the adhesive. Least significant factor is the type of substrates. Sharp drop of the mechanical shear strength between the samples with biggest amount of adhesive (100% - blue marked results) and less amount of adhesive (71% - red marked results, 47% - green marked results) is also seen in Figure 10. It follows that if the mechanical shear strength with 71% of adhesive is sufficient for our application, so we can reduce the

8 amount of adhesive at least on 47% of adhesive and the mechanical shear strength is still sufficient. As mentioned, the type of adhesive is the most significant factor in this experiment. It follows that option of the adhesive is very important and it is possible reach the better results by good choose of the adhesive. The type of substrate is the least significant factor but despite FPCB Ag has a little bit higher mechanical shear strength. Reasons of the higher mechanical shear strength are caused by the different production procedures and properties of substrates. The curing profile is relatively significant factor and newly designed curing profiles [5] have higher mechanical shear strength than profiles from datasheets. The research of these designed profiles will be continued. Substantial differences are not seen in comparison of the samples G and H (Hot air) and the samples I and J (Hot plate) in Figures 7-9. This is the reason of elimination of Hot plate technology from full factorial analysis. We expect that curing by hot plate is helpful for adhesives with short curing time (seconds or few minutes). Fig. 11: Detail of the joint glued by EPO-TEK H20S (left side) and by MG 8331S (right side) on the FPCB Ag. Fig. 12: Detail of the joint glued by EPO-TEK H20S (left side) and by MG 8331S (right side) on the FPCB Cu. The samples were observed by microscopic observation after the test and the typical results of this observation are seen in Figure 11 and 12. Separation of conductive pattern from substrate is seen in Figure 11. This separation is cause by production procedures and properties of the substrate. The cohesive fracture of the joint by EPO-TEK H20S is seen in Figure 12 on the left side. The adhesive fracture of the joint by MG 8331 is seen in Figure 12 on right side.

9 4 CONCLUSION The experiment proved influence of electrically conductive adhesive amount on shear strength of glued joints on flexible substrates. In general the electrically conductive adhesive MG 8331S seems to be the better choice for using on flexible substrates in terms of mechanical shear strength of joint. The results shows that increase of conductive pattern roughness ensure greater mechanical shear strength. As mentioned, the samples with adhesive 8331S on FPCB Cu show adhesive fracture between the conductive pattern and conductive adhesive. This fact is opportunity for the next experiments and for improving of the mechanical shear strength by roughening the copper conductive pattern. The results also shows that newly designed curing profiles increased mechanical shear strength of joints but the question is whether these profiles will not have worse properties after ageing or worse electrical properties. Therefore the research of the properties of electrically conductive adhesive on flexible substrates will be continued. 5 ACKNOWLEDGMENTS This research has been supported by the European Regional Development Fund and the Ministry of Education, Youth and Sports of the Czech Republic under the Regional Innovation Centre for Electrical Engineering (RICE), project No. CZ.1.05/2.1.00/ and by the Student Grant Agency of the University of West Bohemia in Pilsen, grant No. SGS "Technology and Materials Systems in Electrical Engineering. 6 REFERENCES [1] D. Busek, J. Selepova, and P. Mach, Correlations between mechanical and electrical parameters of modified electrically conductive adhesives, Proc th Int. Spring Semin. Electron. Technol., pp , [2] S. Barto, J. Cinert, and P. Mach, Influence of thermal aging on the reliability of electrically conductive adhesives, 2011 IEEE 17th Int. Symp. Des. Technol. Electron. Packag., pp , [3] R. Zhang, J. C. Agar, and C. P. Wong, Recent Advances on Electrically Conductive Adhesives, 12th Electron. Packag. Technol. Conf., no. c, pp , [4] J. Ocklenburg, E. Rastjagaev, and J. Wilde, Investigation of Modern Electrically Conductive Adhesives for Die-attachment in Power Electronics Applications, Electron. Components Technol. Conf. (ECTC 2013), pp , [5] M. Hirman and F. Steiner, A Comparison of the Shear Strength of Conductive Adhesives and Soldering Alloys, in Proceedings of the th International Spring Seminar on Electronics Technology, [6] Y. Gu and D. Jin, Drop test simulation and DOE analysis for design optimization of microelectronics packages, Proc. - Electron. Components Technol. Conf., vol. 2006, pp , 2006.

Thick Film Power Resistor with Thick Printed Copper Terminals

Thick Film Power Resistor with Thick Printed Copper Terminals Thick Film Power Resistor with Thick Printed Copper Terminals Jiri Hlina 1), Jan Reboun 1), Jan Johan 2), Lukas Stepan 2), Ales Hamacek 1) 1) Faculty of Electrical Engineering, Department of Technologies

More information

2W, 2512, 4-Terminal, Low Resistance Chip Resistor (Lead / Halogen Free)

2W, 2512, 4-Terminal, Low Resistance Chip Resistor (Lead / Halogen Free) 2W, 2512, 4-Terminal, Low Resistance Chip Resistor (Lead / Halogen Free) 1. Scope This specification applies to 3.2mm x 6.4mm size 2W, fixed metal foil with ceramic carrier current sensing resistors used

More information

Heriot-Watt University

Heriot-Watt University Heriot-Watt University Heriot-Watt University Research Gateway Optimization and characterisation of bonding of piezoelectric transducers using anisotropic conductive adhesive Cummins, Gerard; Gao, Jun;

More information

INTERFLUX ELECTRONICS NV

INTERFLUX ELECTRONICS NV Reflow soldering temperature profiling Min : 30sec Max : 120sec Max : +4 C/sec Max : 250 C Min : 230 C Min: +0,5 C/sec Min : +1 C/sec Max : +3 C/sec Max : +1 C/sec Max : -6 C/sec Min : -2 C/sec Min : +1

More information

MARCH National Physical Laboratory Hampton Road Teddington Middlesex United Kingdom TW11 0LW

MARCH National Physical Laboratory Hampton Road Teddington Middlesex United Kingdom TW11 0LW NPL REPORT DEPC-MPR 044 Measuring the Impact of Land Size and Solder Joint Volume on Lead-free Solder Joint Reliability M Wickham, L Zou, M Dusek and C P Hunt NOT RESTRICTED MARCH 2006 National Physical

More information

Bonding Parameters of Anisotropic Conductive Adhesive Film and Peeling Strength

Bonding Parameters of Anisotropic Conductive Adhesive Film and Peeling Strength Key Engineering Materials Online: 5-11-15 ISSN: 1-9795, Vols. 97-3, pp 91-9 doi:1./www.scientific.net/kem.97-3.91 5 Trans Tech Publications, Switzerland Bonding Parameters of Anisotropic Conductive Adhesive

More information

NEW DEVELOPMENTS OF DIRECT BONDING ON NON-PRECIOUS METAL SURFACES BY PRESSURE SILVER SINTERING

NEW DEVELOPMENTS OF DIRECT BONDING ON NON-PRECIOUS METAL SURFACES BY PRESSURE SILVER SINTERING NEW DEVELOPMENTS OF DIRECT BONDING ON NON-PRECIOUS METAL SURFACES BY PRESSURE SILVER SINTERING IMAPS-UK Die Attach Workshop 22 November 2018 MTC, Coventry Ly May Chew, Wolfgang Schmitt Heraeus Electronics

More information

SMD RFI CLIP Data Sheet

SMD RFI CLIP Data Sheet 1/14 Attn : Data Sheet - CONDITION : 1. 2. 3. 4. We approved the product as above. WRITE REVIEW APPROVAL ICT NAME S.P. HONG J.E. KIM S.K,JUNG SIGNATURE Supplier : Innochips Technology CO., LTD By President

More information

Future Electronic Devices Technology in Cosmic Space and Lead-free Solder Joint Reliability

Future Electronic Devices Technology in Cosmic Space and Lead-free Solder Joint Reliability The 22nd Microelectronics Work Future Electronic Devices Technology in Cosmic Space and Lead-free Solder Joint Reliability Key Points (1) High Speed Solder Ball Shear Test (2) Relationship between Surface

More information

Relative Reliability Measurements for Electrically Conductive Adhesive Joints on Subtractive Thermoplastic Substrates

Relative Reliability Measurements for Electrically Conductive Adhesive Joints on Subtractive Thermoplastic Substrates Relative Reliability Measurements for Electrically Conductive Adhesive Joints on Subtractive Thermoplastic Substrates Summary This Note describes a new combinational test method for the measurement of

More information

Composition/wt% Bal SA2 (SABI) Bal SA3 (SABI + Cu) Bal

Composition/wt% Bal SA2 (SABI) Bal SA3 (SABI + Cu) Bal Improving Thermal Cycle and Mechanical Drop Impact Resistance of a Lead-free Tin-Silver-Bismuth-Indium Solder Alloy with Minor Doping of Copper Additive Takehiro Wada 1, Seiji Tsuchiya 1, Shantanu Joshi

More information

SCIENCE & TECHNOLOGY

SCIENCE & TECHNOLOGY Pertanika J. Sci. & Technol. 25 (4): 1249-1254 (2017) SCIENCE & TECHNOLOGY Journal homepage: http://www.pertanika.upm.edu.my/ Intermetallic Growth of SAC237 Solder Paste Reinforced with MWCNT Azmah Hanim,

More information

ANISOTROPIC EFFECT WHEN USING ISOTROPIC CONDUCTIVE ADHESIVES

ANISOTROPIC EFFECT WHEN USING ISOTROPIC CONDUCTIVE ADHESIVES ANISOTROPIC EFFECT WHEN USING ISOTROPIC CONDUCTIVE ADHESIVES Jan Felba Marcin Bereski Andrzej Mościcki Wroclaw University of Technology, Poland AMEPOX Microelectronics, Ltd Łódź, Poland Electrically Conductive

More information

Characterization of Coined Solder Bumps on PCB Pads

Characterization of Coined Solder Bumps on PCB Pads Characterization of Coined Solder Bumps on PCB Pads Jae-Woong Nah, Kyung W. Paik, Won-Hoe Kim*, and Ki-Rok Hur** Department of Materials Sci. & Eng., Korea Advanced Institute of Science and Technology

More information

A study aimed at characterizing the interfacial structure in a tin silver solder on nickel-coated copper plate during aging

A study aimed at characterizing the interfacial structure in a tin silver solder on nickel-coated copper plate during aging Sādhanā Vol. 33, Part 3, June 2008, pp. 251 259. Printed in India A study aimed at characterizing the interfacial structure in a tin silver solder on nickel-coated copper plate during aging D C LIN 1,

More information

Lead-Free Solder Bump Technologies for Flip-Chip Packaging Applications

Lead-Free Solder Bump Technologies for Flip-Chip Packaging Applications Lead-Free Solder Bump Technologies for Flip-Chip Packaging Applications Zaheed S. Karim 1 and Jim Martin 2 1 Advanced Interconnect Technology Ltd. 1901 Sunley Centre, 9 Wing Yin Street, Tsuen Wan, Hong

More information

Electrical and reliability properties of isotropic conductive adhesives on immersion silver printed-circuit boards

Electrical and reliability properties of isotropic conductive adhesives on immersion silver printed-circuit boards DOI 10.1007/s00542-008-0678-0 TECHNICAL PAPER Electrical and reliability properties of isotropic conductive adhesives on immersion silver printed-circuit boards J. Lee Æ C. S. Cho Æ J. E. Morris Received:

More information

Sn-Pb plating or Tin plating

Sn-Pb plating or Tin plating 2/14 Unit mm L a a Code letter Dimension L 2..2 W 1.25.2 W t a b.4.1.4.2.4.2 t b b Fig.1 Construction and dimensions NOTE : Resistive element Electrode Protective coat Substrate Nichrome alloy thin film

More information

PROCESSING AND RELIABILITY OF LOW-SILVER-ALLOYS

PROCESSING AND RELIABILITY OF LOW-SILVER-ALLOYS PROCESSING AND RELIABILITY OF LOW-SILVER-ALLOYS Mathias Nowottnick and Andrej Novikov University of Rostock Rostock, Germany mathias.nowottnick@uni-rostock.de Joerg Trodler W.C. Heraeus Hanau, Germany

More information

PCB Production Process HOW TO PRODUCE A PRINTED CIRCUIT BOARD

PCB Production Process HOW TO PRODUCE A PRINTED CIRCUIT BOARD NCAB Group Seminars PCB Production Process HOW TO PRODUCE A PRINTED CIRCUIT BOARD NCAB GROUP PCB Production Process Introduction to Multilayer PCBs 2 Introduction to multilayer PCB s What is a multilayer

More information

SLID bonding for thermal interfaces. Thermal performance. Technology for a better society

SLID bonding for thermal interfaces. Thermal performance. Technology for a better society SLID bonding for thermal interfaces Thermal performance Outline Background and motivation The HTPEP project Solid-Liquid Inter-Diffusion (SLID) Au-Sn SLID Cu-Sn SLID Reliability and bond integrity Alternative

More information

Novel Technique for Flip Chip Packaging of High power Si, SiC and GaN Devices. Nahum Rapoport, Remtec, Inc.

Novel Technique for Flip Chip Packaging of High power Si, SiC and GaN Devices. Nahum Rapoport, Remtec, Inc. Novel Technique for Flip Chip Packaging of High power Si, SiC and GaN Devices Nahum Rapoport, Remtec, Inc. 1 Background Electronic Products Designers: under pressure to decrease cost and size Semiconductor

More information

SMT Adhesive JU - R2S

SMT Adhesive JU - R2S Lead free SOLUTIONS you can TRUST TECHNICAL INFORMATION SMT Adhesive JU - R2S Page 2 of 15 Adhesive to cope with Lead Free soldering and allows self-alignment JU - R2S (SMT heat -cure adhesive in lead

More information

5W, 4527, SL Type Low Resistance Chip Resistor (Lead / Halogen Free)

5W, 4527, SL Type Low Resistance Chip Resistor (Lead / Halogen Free) 5W, 4527, (Lead / Halogen Free) 1. Scope This specification applies to 7.1mm x 12mm size 5W, fixed metal foil current sensing resistors used in electronic equipment. 2. Type Designation RL4527JW (1) (2)

More information

High-Temperature-Resistant Interconnections Formed by Using Nickel Micro-plating and Ni Nano-particles for Power Devices

High-Temperature-Resistant Interconnections Formed by Using Nickel Micro-plating and Ni Nano-particles for Power Devices Kato et al.: High-Temperature-Resistant Interconnections (1/6) [Technical Paper] High-Temperature-Resistant Interconnections Formed by Using Nickel Micro-plating and Ni Nano-particles for Power Devices

More information

Meet the Demands of High-Temperature Applications With Thin Film Resistors

Meet the Demands of High-Temperature Applications With Thin Film Resistors Page 1 of 7 Meet the Demands of High-Temperature Applications With Thin Film Resistors By Dr. Claude Flassayer, Vishay/Sfernice Thin Film Division, www.vishay.com Thursday, September 30, 2010 The demands

More information

Editorial Manager(tm) for Microsystem Technologies Manuscript Draft

Editorial Manager(tm) for Microsystem Technologies Manuscript Draft Editorial Manager(tm) for Microsystem Technologies Manuscript Draft Manuscript Number: Title: Electrical and Reliability Properties of Isotropic Conductive Adhesives on Immersion Silver Printed-Circuit

More information

Packaging Technologies for SiC Power Modules

Packaging Technologies for SiC Power Modules Packaging Technologies for SiC Power Modules Masafumi Horio Yuji Iizuka Yoshinari Ikeda ABSTRACT Wide bandgap materials such as silicon carbide (SiC) and gallium nitride (GaN) are attracting attention

More information

THE EFFECTS OF PLATING MATERIALS, BOND PAD SIZE AND BOND PAD GEOMETRY ON SOLDER BALL SHEAR STRENGTH

THE EFFECTS OF PLATING MATERIALS, BOND PAD SIZE AND BOND PAD GEOMETRY ON SOLDER BALL SHEAR STRENGTH THE EFFECTS OF PLATING MATERIALS, BOND PAD SIZE AND BOND PAD GEOMETRY ON SOLDER BALL SHEAR STRENGTH Keith Rogers and Craig Hillman CALCE Electronic Products and Systems Center University of Maryland College

More information

PROPERTIES OF MODIFIED ELECTRICALLY CONDUCTIVE ADHESIVES

PROPERTIES OF MODIFIED ELECTRICALLY CONDUCTIVE ADHESIVES PROPERTIES OF MODIFIED ELECTRICALLY CONDUCTIVE ADHESIVES Marek RATISLAV, Ivana PILARČÍKOVÁ, David BUŠEK, Pavel MACH CTU-FEE - Technická 2, 166 27 Praha 6, Czech Republic, ratismar@fel.cvut.cz, pilarcik@fel.cvut.cz,

More information

Australian Journal of Basic and Applied Sciences. Pb-Free Solder Ball Robustness Comparison under AC and TC Reliability Test

Australian Journal of Basic and Applied Sciences. Pb-Free Solder Ball Robustness Comparison under AC and TC Reliability Test AENSI Journals Australian Journal of Basic and Applied Sciences ISSN:1991-8178 Journal home page: www.ajbasweb.com Pb-Free Solder Ball Robustness Comparison under AC and TC Reliability Test 1,2 Tan Cai

More information

Best Practice Guide for Thermocycling and Reliability Assessment of Solder Joints

Best Practice Guide for Thermocycling and Reliability Assessment of Solder Joints Best Practice Guide for Thermocycling and Reliability Assessment of Solder Joints Miloš Dušek and Christopher Hunt July 2000 July 2000 Best Practice Guide for Thermocycling and Reliability Assessment of

More information

Surface Mount Sense Resistors

Surface Mount Sense Resistors Resistors Surface Mount Flexible leads for thermal expansion Open-air design reduces PCB heating Values down to 1milliohm Element TCR ±2ppm/ C Zero-ohm 65A jumper version RoHS compliant All parts are Pb-free

More information

CHIP TECHNOLOGIES INC. Chip Resistor Specification

CHIP TECHNOLOGIES INC. Chip Resistor Specification CHIP TECHNOLOGIES INC. Chip Resistor Specification Utech Electronics 1-5250 Finch Ave. East Scarborough, Ontario Canada, M1S 5A4 1-800-268-8832 www.utech.ca 1 1.0 SCOPE... 3 2.0 Part Number Designation.

More information

Lead Free Solder for Flip Chip

Lead Free Solder for Flip Chip Lead Free Solder for Flip Chip Zhenwei Hou & R. Wayne Johnson Laboratory for Electronics Assembly & Packaging Auburn University 162 Broun Hall, ECE Dept. Auburn, AL 36489 USA 334-844-1880 johnson@eng.auburn.edu

More information

1/2W, 0805 Low Resistance Chip Resistor (Lead / Halogen free)

1/2W, 0805 Low Resistance Chip Resistor (Lead / Halogen free) 1. Scope 1/2W, 0805 (Lead / Halogen free) This specification applies to 1.2mm x 2.0mm size 1/2W, fixed metal film chip resistors rectangular type for use in electronic equipment. 2. Type Designation RL

More information

NPL REPORT MAT 6. Preliminary Measurements for Thermoplastic Electronics: Developing a Stress Screening Test. M WICKHAM, L ZOU and C HUNT

NPL REPORT MAT 6. Preliminary Measurements for Thermoplastic Electronics: Developing a Stress Screening Test. M WICKHAM, L ZOU and C HUNT NPL REPORT MAT 6 Preliminary Measurements for Thermoplastic Electronics: Developing a Stress Screening Test M WICKHAM, L ZOU and C HUNT NOT RESTRICTED NOVEMBER 7 Preliminary Measurements for Thermoplastic

More information

Testing Procedures Testing Procedures Parameter Test Tested according to Condition to be satisfied after testing AC/DC Bias Pulse Current Capability P

Testing Procedures Testing Procedures Parameter Test Tested according to Condition to be satisfied after testing AC/DC Bias Pulse Current Capability P Application Notes Testing Procedures SMD Soldering Recommendations 57 Testing Procedures Testing Procedures Parameter Test Tested according to Condition to be satisfied after testing AC/DC Bias Pulse Current

More information

CONDUCTIVE ADHESIVES FOR LOW-STRESS INTERCONNECTION OF THIN BACK-CONTACT SOLAR CELLS

CONDUCTIVE ADHESIVES FOR LOW-STRESS INTERCONNECTION OF THIN BACK-CONTACT SOLAR CELLS ECN-RX--02-027 CONDUCTIVE ADHESIVES FOR LOW-STRESS INTERCONNECTION OF THIN BACK-CONTACT SOLAR CELLS D.W.K. Eikelboom J.H. Bultman A. Schönecker M.H.H. Meuwissen * M.A.J.C. van den Nieuwenhof * D.L. Meier

More information

Critical Use Conditions and their Effect on the Reliability of Soldered Interconnects in Under the Hood Application

Critical Use Conditions and their Effect on the Reliability of Soldered Interconnects in Under the Hood Application 1 Fraunhofer ISIT, Itzehoe Critical Use Conditions and their Effect on the Reliability of Soldered Interconnects in Under the Hood Application Dr. T. Ahrens and Mr. F. W. Wulff, CEM GmbH, Mr. S. Wiese,

More information

Conductive Paste-Based Interconnection Technology for High Performance Probe Card

Conductive Paste-Based Interconnection Technology for High Performance Probe Card Conductive Paste-Based Interconnection Technology for High Performance Probe Card Sang-il Kwon Eddy Kang TSE Co., Ltd. Overview Introduction of TABP Technology Key Technology of Core to Core Interconnection

More information

Lecture 7. Lecture 7. Characterization of Components. Cooling at Component Level. Cooling at Component Level. Cooling at Component Level

Lecture 7. Lecture 7. Characterization of Components. Cooling at Component Level. Cooling at Component Level. Cooling at Component Level Characterization of Components Hans Jonsson Heat flow from chip to heat sink - Thermal Component Models Interface resistance (Contact resistance) TIM Thermal Interface Materials Project assignment The

More information

Company Overview Markets Products- Capabilities

Company Overview Markets Products- Capabilities Company Overview Markets Products- Capabilities A Simpler way for PCB production. www.purepcb.co.uk What can Pure do for you? From 1 off Circuit upward, No MOQ/MOV High Mix Production Focus. Fast Turn

More information

LabVIEW Simulation for Electroplating Process of Plated- Through Hole (PTH) in Multilayer Printed Circuit Board (PCB)

LabVIEW Simulation for Electroplating Process of Plated- Through Hole (PTH) in Multilayer Printed Circuit Board (PCB) LabVIEW Simulation for Electroplating Process of Plated- Through Hole (PTH) in Multilayer Printed Circuit Board (PCB) M Arifin 1,2*, A B K Atmaja 1, and V Octowinandi 1,2 1 Department of Electrical Engineering,

More information

An Assessment of the Impact of Lead-Free Assembly Processes on Base Material and PCB Reliability

An Assessment of the Impact of Lead-Free Assembly Processes on Base Material and PCB Reliability An Assessment of the Impact of Lead-Free Assembly Processes on Base Material and PCB Reliability Edward Kelley Isola Abstract Environmental regulations are forcing the elimination of lead (Pb) from electronic

More information

Microcontact Printing Procedures for Adhesive and Conductive Epoxies

Microcontact Printing Procedures for Adhesive and Conductive Epoxies Microcontact Printing Procedures for Adhesive and Conductive Epoxies This objective was accomplished through a formal record of the procedures to deliver a stamped product which met the benchmark mechanical,

More information

RoHS Compliance Document

RoHS Compliance Document D2-Pak RoHS Compliance Document Contents: 1. 2. Solder Reflow 3. Tin Whisker Report D2-pak (3 or 5 Lead) BOM 1 90598-46-2 0.05808 11% 3.8% Lead Frame Copper 0.94840 Die Attach Soft Solder 0.01200 Cu 7440-50-8

More information

Project Management Enriched by Engineering Design Science during the Design Process of a Technical Product

Project Management Enriched by Engineering Design Science during the Design Process of a Technical Product The 3rd International Conference on Design Engineering and Science, ICDES 2014 Pilsen, Czech Republic, August 31 September 3, 2014 Project Management Enriched by Engineering Design Science during the Design

More information

Product Documentation MS1V-T1K

Product Documentation MS1V-T1K Product Documentation Quartz Crystal Unit 32.768 khz February 2017 1/12 Rev. 1.0 2. Product Description The is a low frequency surface mount technology Quartz Crystal Unit that incorporates a tuning fork

More information

Data sheet FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & LOW OHM RLC10, 16, 20, 32, 35, 50, 63. AEC-Q200 qualified

Data sheet FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & LOW OHM RLC10, 16, 20, 32, 35, 50, 63. AEC-Q200 qualified No.: RLC-K-HTS-0001 /17 Date: 2017. 4. 21 Data sheet FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & LOW OHM Style: RLC10, 16, 20, 32, 35, 50, 63 AEC-Q200 qualified RoHS COMPLIANCE ITEM Halogen and

More information

Freescale Semiconductor Tape Ball Grid Array (TBGA) Overview

Freescale Semiconductor Tape Ball Grid Array (TBGA) Overview Freescale Semiconductor Tape Ball Grid Array (TBGA) Overview Revision 0 2006 Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the

More information

The Effect of Cu and Ni on the Structure and Properties of the IMC Formed by the Reaction of Liquid Sn-Cu Based Solders with Cu Substrate

The Effect of Cu and Ni on the Structure and Properties of the IMC Formed by the Reaction of Liquid Sn-Cu Based Solders with Cu Substrate WDS'08 Proceedings of Contributed Papers, Part III, 220 224, 2008. ISBN 978-80-7378-067-8 MATFYZPRESS The Effect of Cu and Ni on the Structure and Properties of the IMC Formed by the Reaction of Liquid

More information

Study of the Interface Microstructure of Sn-Ag-Cu Lead-Free Solders and the Effect of Solder Volume on Intermetallic Layer Formation.

Study of the Interface Microstructure of Sn-Ag-Cu Lead-Free Solders and the Effect of Solder Volume on Intermetallic Layer Formation. Study of the Interface Microstructure of Sn-Ag-Cu Lead-Free Solders and the Effect of Solder Volume on Intermetallic Layer Formation. B. Salam +, N. N. Ekere, D. Rajkumar Electronics Manufacturing Engineering

More information

THE INFLUENCE OF THERMAL LOAD ON PROPERTIES OF HETEROGENEOUS JOINTS BETWEEN STEEL AND ALUMINIUM ALLOY A. FRANC 1, J. TESAŘ 2

THE INFLUENCE OF THERMAL LOAD ON PROPERTIES OF HETEROGENEOUS JOINTS BETWEEN STEEL AND ALUMINIUM ALLOY A. FRANC 1, J. TESAŘ 2 CO 2 /Km [g] THE INFLUENCE OF THERMAL LOAD ON PROPERTIES OF HETEROGENEOUS JOINTS BETWEEN STEEL AND ALUMINIUM ALLOY A. FRANC 1, J. TESAŘ 2 1 Faculty of Mechanical Engineering, University of West Bohemia,

More information

Bob Willis Process Guides

Bob Willis Process Guides Practical Selection/Problems with SMT Adhesives Bob Willis Surface M ount Technology (SM T) first started with the introduction of mixed technology designs incorporating components mounted on the underside

More information

DITF ToolKit 1. Standard Substrate Sizes (selected at the factory for optimum process)

DITF ToolKit 1. Standard Substrate Sizes (selected at the factory for optimum process) DITF ToolKit 1 DITF Toolkit Substrates Common Substrate Materials Alumina (99.5% min) єr = 9.9 Tan d = 1.5 x10-4 Aluminum Nitride (K170) єr = 8.9 Tan d = 2.0 x10-3 Beryllia (99.5%) єr = 6.7 Tan d = 3.0

More information

Application Note AN-1023

Application Note AN-1023 Surface Mounting of Larger Devices by Pamela Dugdale and Arthur Woodworth Table of Contents Page Introduction...1 Board Materials...1 Thermal Resistance...1 Board Mounting...1 Board Attach Materials...2

More information

Building HDI Structures using Thin Films and Low Temperature Sintering Paste

Building HDI Structures using Thin Films and Low Temperature Sintering Paste Building HDI Structures using Thin Films and Low Temperature Sintering Paste Catherine Shearer, James Haley and Chris Hunrath Ormet Circuits Inc. - Integral Technology California, USA chunrath@integral-hdi.com

More information

CONDUCTIVE ADHESIVES FOR SOLID TANTALUM CAPACITORS PROCESS AND ESR OPTIMISATION BY MATERIAL SELECTION*

CONDUCTIVE ADHESIVES FOR SOLID TANTALUM CAPACITORS PROCESS AND ESR OPTIMISATION BY MATERIAL SELECTION* Active and Passive Elec. Comp., 2002, Vol. 25, pp. 133 139 CONDUCTIVE ADHESIVES FOR SOLID TANTALUM CAPACITORS PROCESS AND ESR OPTIMISATION BY MATERIAL SELECTION* G. DREEZEN{, E. DECKX and G. LUYCKX Emerson

More information

Sp e c i f i c a t i o n

Sp e c i f i c a t i o n K M Y Last update: 2015.4.4 No.RLC-K-HTS-0001-15 (Uncontrolled copy) Sp e c i f i c a t i o n (Reference) FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND LOW OHM Style: RLC10, 16, 20, 32, 35, 50,

More information

Chapter 14. Designing with FineLine BGA Packages

Chapter 14. Designing with FineLine BGA Packages Chapter 14. Designing with FineLine BGA Packages S53009-1.3 Chapter 14, Designing with FineLine BGA Packages, replaces AN 114: Designing with FineLine BGA Packages. Introduction As programmable logic devices

More information

ENHANCING MECHANICAL SHOCK PERFORMANCE USING EDGEBOND TECHNOLOGY

ENHANCING MECHANICAL SHOCK PERFORMANCE USING EDGEBOND TECHNOLOGY ENHANCING MECHANICAL SHOCK PERFORMANCE USING EDGEBOND TECHNOLOGY Steven Perng, Tae-Kyu Lee, and Cherif Guirguis Cisco Systems, Inc. San Jose, CA, USA sperng@cisco.com Edward S. Ibe Zymet, Inc. East Hanover,

More information

ENHANCING WLCSP RELIABILITY THROUGH BUILD-UP STRUCTURE IMPROVEMENTS AND NEW SOLDER ALLOYS

ENHANCING WLCSP RELIABILITY THROUGH BUILD-UP STRUCTURE IMPROVEMENTS AND NEW SOLDER ALLOYS ENHANCING WLCSP RELIABILITY THROUGH BUILD-UP STRUCTURE IMPROVEMENTS AND NEW SOLDER ALLOYS B. Rogers, M. Melgo, M. Almonte, S. Jayaraman, C. Scanlan, and T. Olson Deca Technologies, Inc 7855 S. River Parkway,

More information

Using PDMS Micro-Transfer Moulding for Polymer Flip Chip Packaging on MEMS

Using PDMS Micro-Transfer Moulding for Polymer Flip Chip Packaging on MEMS Using PDMS Micro-Transfer Moulding for Polymer Flip Chip Packaging on MEMS Edward K.L. Chan, Cell K.Y. Wong, M. Lee, Matthew M.F. Yuen, Yi-Kuen Lee Department of Mechanical Engineering Hong Kong University

More information

Two Chips Vertical Direction Embedded Miniaturized Package

Two Chips Vertical Direction Embedded Miniaturized Package Two Chips Vertical Direction Embedded Miniaturized Package Shunsuke Sato, 1 Koji Munakata, 1 Masakazu Sato, 1 Atsushi Itabashi, 1 and Masatoshi Inaba 1 Continuous efforts have been made to achieve seemingly

More information

Question: Are RO4000 materials compatible with lead-free processes? Answer:

Question: Are RO4000 materials compatible with lead-free processes? Answer: Question: Are RO4 materials compatible with lead-free processes? Answer: RO4 cores and prepregs are among the most temperature stable products available. They easily meet or exceed all expectations for

More information

Influence of laser marking on stainless steel surface and corrosion resistance

Influence of laser marking on stainless steel surface and corrosion resistance Lasers in Manufacturing Conference 2015 Influence of laser marking on stainless steel surface and corrosion resistance Martin Kučera a *, Michal Švantner a, Eva Smazalová a a, New Technologies - Research

More information

Three-Dimensional Molded Interconnect Devices (3D-MID)

Three-Dimensional Molded Interconnect Devices (3D-MID) Jörg Frank Three-Dimensional Molded Interconnect Devices (3D-MID) Materials, Manufacturing, Assembly and Applica ons for Injec on Molded Circuit Carriers Sample Pages ISBN 978-1-56990-551-7 HANSER Hanser

More information

Optimizing Immersion Silver Chemistries For Copper

Optimizing Immersion Silver Chemistries For Copper Optimizing Immersion Silver Chemistries For Copper Ms Dagmara Charyk, Mr. Tom Tyson, Mr. Eric Stafstrom, Dr. Ron Morrissey, Technic Inc Cranston RI Abstract: Immersion silver chemistry has been promoted

More information

ELCOSINT Webinar NPL. Sept 2015

ELCOSINT Webinar NPL. Sept 2015 ELCOSINT Webinar NPL Sept 2015 1 About NPL The UK s national standards laboratory 36,000 m 2 national laboratory Founded in 1900 World leading National Measurement Institute 600+ specialists in Measurement

More information

High Temperature (245 C) Thick Film Chip Resistor

High Temperature (245 C) Thick Film Chip Resistor High Temperature (245 C) Thick Film Chip Resistor For applications such as down hole applications or aircraft breaking systems, the need for parts able to withstand very severe conditions (temperature

More information

XTSC SiCap 400µm - NiAu finishing - Assembly by soldering

XTSC SiCap 400µm - NiAu finishing - Assembly by soldering General description This document describes the attachment techniques recommended by Murata* for their XTSC silicon capacitors on the customer substrates. This document is non-exhaustive. Customers with

More information

ALTERNATIVES TO SOLDER IN INTERCONNECT, PACKAGING, AND ASSEMBLY

ALTERNATIVES TO SOLDER IN INTERCONNECT, PACKAGING, AND ASSEMBLY ALTERNATIVES TO SOLDER IN INTERCONNECT, PACKAGING, AND ASSEMBLY Herbert J. Neuhaus, Ph.D., and Charles E. Bauer, Ph.D. TechLead Corporation Portland, OR, USA herb.neuhaus@techleadcorp.com ABSTRACT Solder

More information

System Level Effects on Solder Joint Reliability

System Level Effects on Solder Joint Reliability System Level Effects on Solder Joint Reliability Maxim Serebreni 2004 2010 Outline Thermo-mechanical Fatigue of solder interconnects Shear and tensile effects on Solder Fatigue Effect of Glass Style on

More information

Study and mechanical characterization of high temperature power electronic packaging

Study and mechanical characterization of high temperature power electronic packaging Study and mechanical characterization of high temperature power electronic packaging A. BAAZAOUI a, O. DALVERNY a, J. ALEXIS a, M. KARAMA a a. Université de Toulouse; INP/ENIT; LGP ; 47 avenue d'azereix;

More information

Optimizing Immersion Silver Chemistries For Copper

Optimizing Immersion Silver Chemistries For Copper Optimizing Immersion Silver Chemistries For Copper Ms Dagmara Charyk, Mr. Tom Tyson, Mr. Eric Stafstrom, Dr. Ron Morrissey, Technic Inc Cranston RI Abstract: Immersion silver chemistry has been promoted

More information

IMPACT OF MICROVIA-IN-PAD DESIGN ON VOID FORMATION

IMPACT OF MICROVIA-IN-PAD DESIGN ON VOID FORMATION IMPACT OF MICROVIA-IN-PAD DESIGN ON VOID FORMATION Frank Grano, Felix Bruno Huntsville, AL Dana Korf, Eamon O Keeffe San Jose, CA Cheryl Kelley Salem, NH Joint Paper by Sanmina-SCI Corporation EMS, GTS

More information

ANISOTROPIC conductive film (ACF) is a film-type

ANISOTROPIC conductive film (ACF) is a film-type 1350 IEEE TRANSACTIONS ON COMPONENTS, PACKAGING AND MANUFACTURING TECHNOLOGY, VOL. 5, NO. 9, SEPTEMBER 2015 Effects of Bonding Pressures and Bonding Temperatures on Solder Joint Morphology and Reliability

More information

A. Feature Good wettability and antioxidation effect of flux

A. Feature Good wettability and antioxidation effect of flux A. Feature wettability and antioxidation effect of flux We have considered active temperature and persistence of flux, and selected activator newly. As results of this, J3-8843-KG has good wettability

More information

Mechanical Reliability A New Method to Forecast Drop Shock Performance

Mechanical Reliability A New Method to Forecast Drop Shock Performance Mechanical Reliability A New Method to Forecast Drop Shock Performance Ronald Frosch Guenther Mayr, Manfred Riedler AT&S Shanghai, China Abstract In light of the recent technological trends within PCB

More information

Q&A ThinPAK 8x8. New leadless SMD package for CoolMOS. May 2010 V 1.1

Q&A ThinPAK 8x8. New leadless SMD package for CoolMOS. May 2010 V 1.1 Q&A ThinPAK 8x8 New leadless SMD package for CoolMOS May 2010 V 1.1 Contents Package outline Manufacturing Package quality Materials and packing Electrical and thermal characteristics General 2010-01-14

More information

Murata Silicon Capacitors - XTSC 400µm NiAu finishing Assembly by Soldering High temperature silicon capacitor. Table of Contents

Murata Silicon Capacitors - XTSC 400µm NiAu finishing Assembly by Soldering High temperature silicon capacitor. Table of Contents Table of Contents Table of Contents...1 Introduction...2 Handling precautions and storage...2 Pad opening...3 Process Flow...5 Solder print material and stencil printing recommendations...6 Pick and Place...7

More information

NTC Thermistors. Mounting instructions. Date: January 2018

NTC Thermistors. Mounting instructions. Date: January 2018 NTC Thermistors Mounting instructions Date: January 2018 EPCOS AG 2018. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without

More information

IMC Layers Formed with Various Combinations of Solders and Surface Finishes and Their Effect on Solder Joint Reliability

IMC Layers Formed with Various Combinations of Solders and Surface Finishes and Their Effect on Solder Joint Reliability IMC Layers Formed with Various Combinations of Solders and Surface Finishes and Their Effect on Solder Joint Reliability Per-Erik Tegehall, Swerea IVF 4 th Electronic Materials and Assembly Processes for

More information

Electrical Specifications. Maximum Overload Current (A) Maximum Rating Current (A)

Electrical Specifications. Maximum Overload Current (A) Maximum Rating Current (A) Features: High power metal alloy current sense resistor High temperature performance up to 225 C; for operation up to 275ºC, contact factory Low thermal EMF (

More information

FrelTec GmbH. Current Sensing Metal Chip Resistor SMD

FrelTec GmbH. Current Sensing Metal Chip Resistor SMD GmbH Mathildenstr. 10A 82319 Starnberg Germany Current Sensing Metal Chip Resistor SMD 4/18/2013 1/10 GmbH www.freltec.com SPECIFICATION Part Number 046 06 * R010 * J * T05 ** E D Type Size Value Tolerance

More information

ELECTRICAL, THERMOMECHANICAL AND RELIABILITY MODELING OF ELECTRICALLY CONDUCTIVE ADHESIVES

ELECTRICAL, THERMOMECHANICAL AND RELIABILITY MODELING OF ELECTRICALLY CONDUCTIVE ADHESIVES ELECTRICAL, THERMOMECHANICAL AND RELIABILITY MODELING OF ELECTRICALLY CONDUCTIVE ADHESIVES A Dissertation Presented to The Academic Faculty by Bin Su In Partial Fulfillment of the Requirements for the

More information

Power Electronics Packaging Solutions for Device Junction Temperature over 220 o C

Power Electronics Packaging Solutions for Device Junction Temperature over 220 o C EPRC 12 Project Proposal Power Electronics Packaging Solutions for Device Junction Temperature over 220 o C 15 th August 2012 Page 1 Motivation Increased requirements of high power semiconductor device

More information

General Information on the Assembly and Solder Pad Design of the DRAGON Family Application Note

General Information on the Assembly and Solder Pad Design of the DRAGON Family Application Note General Information on the Assembly and Solder Pad Design of the DRAGON Family Application Note Abstract This application note gives general information on the assembly and design of the solder pad of

More information

Wire-bonds Durability in High-temperature Applications M. Klíma, B. Psota, I. Szendiuch

Wire-bonds Durability in High-temperature Applications M. Klíma, B. Psota, I. Szendiuch Ročník 2013 Číslo V Wire-bonds Durability in High-temperature Applications M. Klíma, B. Psota, I. Szendiuch Department of Microelectronics, Faculty of Electrical Engineering and Communication, Brno University

More information

High Temperature (245 C) Thick Film Chip Resistor

High Temperature (245 C) Thick Film Chip Resistor High Temperature (245 C) Thick Film Chip Resistor DESIGN SUPPORT TOOLS Models Available click logo to get started FEATURES High temperature (245 C) Large ohmic value range 0.1 to 100 M Available Operating

More information

Optimisation of MWT cells and modules

Optimisation of MWT cells and modules Optimisation of MWT cells and modules Lowering the cost of foil-based back-contact PV MWT Workshop Shanghai 19 th May 2014 www.ecn.nl Why back-contact cells and modules? Limitations of H-pattern cells

More information

Conductive Hole Plugging Product

Conductive Hole Plugging Product TAIYO SCHP-7901 Board Thickness = 62mils Board Thickness = 62mils Hole Diameter = 8 mils Hole Diameter = 14 mils Silver Conductive hole fill material Single-Component this is Thermally Cured Fills holes

More information

Sn623-5T-E SOLDER PASTE

Sn623-5T-E SOLDER PASTE Sn623-5T-E SOLDER PASTE INTRODUCTION Singapore Asahi s solder paste Sn623-5T-E is a silver bearing paste to prevent silver migration and brittleness. It is formulated for fine pitch applications up to

More information

EP A2 (19) (11) EP A2 (12) EUROPEAN PATENT APPLICATION. (43) Date of publication: Bulletin 2006/23

EP A2 (19) (11) EP A2 (12) EUROPEAN PATENT APPLICATION. (43) Date of publication: Bulletin 2006/23 (19) Europäisches Patentamt European Patent Office Office européen des brevets (12) EUROPEAN PATENT APPLICATION (11) EP 1 667 226 A2 (43) Date of publication: 07.06.06 Bulletin 06/23 (1) Int Cl.: H01L

More information

LGIT CSP Application NOTE. (Lighting)

LGIT CSP Application NOTE. (Lighting) LGIT CSP Application NOTE (Lighting) TABLE OF CONTENTS 1. LGIT CSP Detail -------------- P2 2. LGIT CSP PCB Design -------------- P3 2.1. LGIT CSP Footprint and PCB Pattern -------------- P3 2.2. PCB Substrate

More information

DEGRADATION THE REFRACTORIES OF ROTARY FURNACE LININGS IN THE PRODUCTION OF ZINC OXIDE

DEGRADATION THE REFRACTORIES OF ROTARY FURNACE LININGS IN THE PRODUCTION OF ZINC OXIDE DEGRADATION THE REFRACTORIES OF ROTARY FURNACE LININGS IN THE PRODUCTION OF ZINC OXIDE Natália LUPTÁKOVÁ a, Františka PEŠLOVÁ a, Evgeniy ANISOMOV b, Adriana PAVÚČKOVÁ a, Michaela FERODOVÁ a a University

More information

Technical Brief. 2 Experiments. Journal of Manufacturing Science and Engineering AUGUST 2007, Vol. 129 / 843 Copyright 2007 by ASME

Technical Brief. 2 Experiments. Journal of Manufacturing Science and Engineering AUGUST 2007, Vol. 129 / 843 Copyright 2007 by ASME Journal of Manufacturing Science and Engineering Technical Brief Experimental Study of Demolding Properties on Stereolithography Tooling Chao-Chyun An Ren-Haw Chen e-mail: chenrh@mail.nctu.edu.tw Department

More information

Reference Only. 2.Part Numbering (ex) NF Z 5B BW 2R9 L N 1 0 L

Reference Only. 2.Part Numbering (ex) NF Z 5B BW 2R9 L N 1 0 L SpecNo.JENF243J-0011A-01 P1/10 CHIP NOISE FILTER NFZ5BBW LN10 REFERENCE SPECIFICATION 1.Scope This reference specification applies to NFZ5BBW_LN10L Series, Chip Noise Filter. 2.Part Numbering (ex) NF Z

More information

Recovery of Metals from Sn-Ag-Cu Solder Alloy Dross

Recovery of Metals from Sn-Ag-Cu Solder Alloy Dross Proceedings of the International Conference on Mining, Material and Metallurgical Engineering Prague, Czech Republic, August 11-12, 2014 Paper No. 79 Recovery of Metals from Sn-Ag-Cu Solder Alloy Dross

More information