PowerClean DNA Clean-Up Kit

Transcription

1 PowerClean DNA Clean-Up Catalog No. Quantity Preps Instruction Manual New protocol instruction: Shake Solution 5 to mix before using to ensure consistent results. Inhibitor Removal Technology (IRT) is a registered trademark of MO BIO Laboratories, Inc. and is covered by US patent protection as well as international patents pending. Please recycle Version:

2 Table of Contents Introduction... 3 Protocol Overview... 3 Equipment Required... 4 Contents & Storage... 4 Precautions & Warnings... 4 Protocols: Experienced User Protocol...5 Detailed Protocol (Describes what is happening at each step)... 6 Hints & Troubleshooting Guide... 9 Contact Information...10 Other Quality Products Available

3 Introduction The PowerClean DNA Clean-Up utilizes our patented Inhibitor Removal Technology (IRT) to provide researchers with a novel and proprietary method for cleaning up previously isolated genomic DNA. Starting DNA may be amber to brown in appearance; an indicator of PCR inhibiting substances, particularly humics and polyphenols. Even samples that appear colorless may contain PCR inhibitors which can be cleaned up with this kit. The PowerClean DNA Clean-Up will remove this brown color as well as any PCR inhibiting substances, such as heme, polysaccharides, polyphenols fulvic acids and dyes. A high level of purity is achieved with the PowerClean DNA Clean-Up, allowing for more successful PCR amplification of DNA derived from organisms in the original sample. This kit was validated with DNA isolated from a variety of problematic soils and also with artificially spiked DNA samples with commercial humic acids. However, it performs well on DNA isolated from virtually any sample source. Protocol Overview Archived or previously isolated DNA samples are purified when added to our proprietary DNA Clean-Up reagents. Inhibitors are selectively removed from the DNA solution. All DNA including total genomic DNA is captured on a silica membrane in a spin column format. DNA is then washed and eluted from the membrane. Percentage recovery varies depending on the level of inhibitors in the DNA that may be influencing the DNA yield measurement. Purified DNA is ready for PCR analysis and other downstream applications. This kit is for research purposes only. Not for diagnostic use. Other Related Products Catalog No. Quantity PowerSoil DNA Isolation UltraClean PCR Clean-Up UltraClean GelSpin DNA Extraction

4 Equipment Required Microcentrifuge (13,000 x g) Pipettor (20 l l) Vortex-Genie 2 Vortex (MO BIO Catalog# V or V-220) Contents Catalog # Component Catalog # Amount PowerClean DNA Solution ml PowerClean DNA Solution ml PowerClean DNA Solution ml PowerClean DNA Solution ml PowerClean DNA Solution ml PowerClean DNA Solution ml PowerClean DNA Solution ml PowerClean DNA Spin Filters SF 50 PowerClean DNA 2 ml Collection Tubes T 200 Storage reagents and components should be stored at room temperature (15-30 C). Precautions Please wear gloves when using this product. Avoid all skin contact with kit reagents. In case of contact, wash thoroughly with water. Do not ingest. See Material Safety Data Sheets for emergency procedures in case of accidental ingestion or contact. All MSDS information is available upon request ( ) or at Reagents labeled flammable should be kept away from open flames and sparks. WARNING: PowerClean DNA Solution 6 contains ethanol. It is flammable. IMPORTANT NOTE FOR USE: Shake to mix PowerClean DNA Solution 5 before use. 4

5 Experienced User Protocol Please wear gloves at all times 1. Add up to 150 l of DNA sample to 2 ml Collection Tube (provided). If less than 150 l is added, adjust volume with distilled water. 2. Add 70 l of PowerClean DNA Solution 1 to DNA. Gently invert 3-5 times to mix. 3. Check PowerClean DNA Solution 2. If it has precipitated, heat to 60 C and gently invert the tube periodically until it has completely dissolved. Vigorous shaking will result in foaming. This solution may be used while still warm. 4. Add 20 l of PowerClean DNA Solution 2 and invert 3-5 times to mix. 5. Add 85 l of PowerClean DNA Solution 3 and invert 3-5 times to mix. Incubate at 4 C for 5 minutes. 6. Centrifuge at 10,000 x g for 1 minute at room temperature. 7. Avoiding pellet, transfer the entire volume of supernatant to a clean 2 ml Collection Tube (provided). 8. Add 70 l of PowerClean DNA Solution 4 and invert 3-5 times to mix. Incubate at 4 C for 5 minutes. 9. Centrifuge at 10,000 x g for 1 minute at room temperature. 10. Avoiding pellet, transfer the supernatant into a clean 2 ml Collection Tube (provided). 11. Shake to mix PowerClean DNA Solution 5. Add 800 l of PowerClean DNA Solution 5 to the supernatant and vortex for 5 seconds. 12. Load approximately 600 l onto Spin Filter and centrifuge at 10,000 x g for 1 minute at room temperature. Discard flow through. Add remaining 600 l supernatant to Spin Filter and centrifuge at 10,000 x g for 1 minute at room temperature. Note: A total of two loads for each sample processed may be required. 13. Add 500 l of PowerClean DNA Solution 6 to Spin Filter and centrifuge at 10,000 x g for 30 seconds at room temperature 14. Discard flow through. Optional: An additional wash of the Spin Filter with 100% ethanol may be performed prior to the final dry spin. This may enhance the purity for some sample types. After decanting the flow through from step 14, add 650µl of 100% ethanol to the spin column and centrifuge at 10,000 x g for 30 seconds. To completely remove residual ethanol, decant the flow through and increase the dry spin (step 15) to 2 minutes at 13,000 x g or max speed. Continue with step Centrifuge Spin Filter at 13,000 x g for 1 minute at room temperature. 16. Carefully place Spin Filter in new 2 ml Collection Tube (provided). Avoid splashing any PowerClean DNA Solution 6 onto Spin Filter. 17. If starting with 50 l of genomic DNA, add 50 l of PowerClean DNA Solution 7 to center of white filter membrane. If starting with 100 or 150 l of genomic DNA, add 100 l of PowerClean DNA Solution 7 to center of white filter membrane. Note: For efficient elution, use a minimum of 50 µl of PowerClean DNA Solution 7, irrespective of starting volume. By reducing elution volume, it is possible to obtain DNA in a more concentrated form. 18. Centrifuge at 10,000 x g for 30 seconds at room temperature. 19. Discard Spin Filter. DNA in 2 ml Collection Tube is now application ready. No further steps are required. We recommend storing DNA frozen (-20 to -80 C). PowerClean DNA Solution 7 does not contain EDTA. Thank you for choosing the PowerClean DNA Clean-Up. 5

6 Detailed Protocol (Describes what is happening at each step) Please wear gloves at all times 1. Add up to 150 l of DNA sample to a 2 ml Collection Tube (provided). If less than 150 l is added, adjust the volume with distilled water. What s happening: After the sample has been added to the Collection Tube, a disassociation procedure is performed. The PowerClean DNA Solutions contain reagents that will (a) help disperse molecular interactions, (b) begin to dissolve humic substances and (c) protect nucleic acids from degradation. 2. Add 70 l of PowerClean DNA Solution 1 to the DNA. Gently invert 3-5 times to mix. What s happening: Gentle inversion of the tube mixes the components in the tube and begins to disassociate DNA from PCR inhibiting substances. 3. Check PowerClean DNA Solution 2. If it has precipitated, heat to 60 C and gently invert the tube periodically until it has completely dissolved. Vigorous shaking will result in foaming. This solution may be used while it is still warm. What s happening: PowerClean DNA Solution 2 contains detergents and other agents required for complete disassociation. The chemicals in PowerClean DNA Solution 2 will precipitate under cold storage conditions. Heating to 60 C will dissolve the reagent or the other disassociation agents. PowerClean DNA Solution 2 can be used while it is warm. 4. Add 20 l of PowerClean DNA Solution 2 and gently invert 3-5 times to mix. 5. Add 85 l of PowerClean DNA Solution 3 and gently invert 3-5 times to mix. Incubate at 4 C for 5 minutes. What s happening: PowerClean DNA Solution 3 is patented Inhibitor Removal Technology (IRT). It contains a reagent that precipitates non-dna organic and inorganic materials, including humic substances and proteins. It is important to remove contaminating organic and inorganic matter that may reduce DNA purity and inhibit downstream DNA applications. Note: Expect between l of supernatant at this step. The exact recovered volume depends on the nature of your starting material and is not critical for the procedure to be effective. The supernatant may still be dark in appearance. The presence of a dark color in the mixture is expected in many sample types at this step. Subsequent steps in the protocol will remove the coloration of the mixture. 6. Centrifuge the tube at 10,000 x g for 1 minute at room temperature. 7. Avoiding the pellet, transfer the entire supernatant to a clean 2 ml Collection Tube (provided). What s happening: The pellet contains non-dna organic and inorganic materials, including humic substances and proteins. For the best DNA yield and quality, avoid transferring any of the pellet. 8. Add 70 l of PowerClean DNA Solution 4 and gently invert 3-5 times to mix. Incubate at 4 C for 5 minutes. What s happening: PowerClean DNA Solution 4 is patented Inhibitor Removal Technology (IRT) and is the second reagent to precipitate additional non-dna organic and inorganic materials, including humic substances 6

7 and proteins. It is important to remove contaminating organic and inorganic matter that may reduce DNA purity and inhibit downstream DNA applications. 9. Centrifuge the tube at 10,000 x g for 1 minute at room temperature. 10. Transfer the supernatant to a clean 2 ml Collection Tube (provided). What s happening: The pellet contains additional non-dna organic and inorganic materials, including humic substances and proteins. For the best DNA yield and quality, avoid transferring any of the pellet. 11. Shake to mix PowerClean DNA Solution 5. Add 800 l of PowerClean DNA Solution 5 to the supernatant (be careful that solution doesn t exceed rim of 2 ml Collection Tube) and vortex for 5 seconds. What s happening: PowerClean DNA Solution 5 is a high salt concentration solution. Since DNA binds tightly to silica at high salt concentrations, this solution will adjust the salt concentrations to allow binding of DNA, but not non-dna organic and inorganic material that may still be present at low levels, to the Spin Filters. 12. Load approximately 600 l onto a Spin Filter and centrifuge at 10,000 x g for 1 minute at room temperature. Discard the flow through and load the remaining 600 l supernatant onto the Spin Filter and centrifuge at 10,000 x g for 1 minute at room temperature. Note: A total of two loads for each sample processed may be required. What s happening: DNA is selectively bound to the silica membrane in the Spin Filter device in the high salt solution. Contaminants pass through the filter membrane, leaving only the DNA bound to the membrane. 13. Add 500 l of PowerClean DNA Solution 6 and centrifuge at 10,000 x g for 30 seconds at room temperature. What s happening: This solution is an ethanol based wash solution used to further clean the DNA that is bound to the silica filter membrane in the Spin Filter. This wash solution removes residues of salt, humic substances, and other contaminants while allowing the DNA to stay bound to the silica membrane. 14. Discard the flow through from the 2 ml Collection Tube. What s happening: The flow through fraction is non-dna organic and inorganic waste removed from the silica spin filter membrane by the ethanol wash solution. Optional: An additional wash of the Spin Filter with 100% ethanol may be performed prior to the final dry spin. This may enhance the purity for some sample types. After decanting the flow through from step 14, add 650µl of 100% ethanol to the spin column and centrifuge at 10,000 x g for 30 seconds. To completely remove residual ethanol, decant the flow through and increase the dry spin (step 15) to 2 minutes at 13,000 x g or max speed. Continue with step Centrifuge at 13,000 x g for 1 minute at room temperature. What s happening: This second spin removes residual ethanol wash solution. It is critical to remove all traces of wash solution because the ethanol in PowerClean DNA Solution 6 can interfere with many downstream applications such as PCR, restriction digests and gel electrophoresis. 7

8 16. Carefully place the Spin Filter in a new 2 ml Collection Tube (provided). Avoid splashing any PowerClean DNA Solution 6 onto the Spin Filter. Note: It is important to avoid any traces of the ethanol based wash solution. 17. If starting with 50 l of genomic DNA, add 50 l of PowerClean DNA Solution 7 to the center of the white filter membrane. If starting with 100 or 150 l of genomic DNA, add 100 l of PowerClean DNA Solution 7 to the center of the white filter membrane. For efficient elution, use a minimum of 50 µl of PowerClean DNA Solution 7, irrespective of the starting volume. By reducing the elution volume, it is possible to obtain DNA in a more concentrated form. For example, you can concentrate the DNA present in 150 µl initially, after going through the PowerClean DNA Clean-Up protocol. Note: Placing this Solution (sterile elution buffer) in the center of the small white membrane will make sure the entire membrane is wetted. This will result in a more efficient release of the DNA from the silica Spin Filter membrane. As PowerClean DNA Solution 7 (sterile elution buffer) passes through the silica membrane, DNA is released because it only stays bound to the silica Spin Filter membrane in the presence of high concentration of salt. PowerClean DNA Solution 7 is 10mM Tris ph 8 and does not contain EDTA. Alternatively, sterile DNA-Free PCR Grade Water (MO BIO Laboratories Catalog# ) may be used for elution from the silica Spin Filter membrane at this step. 18. Centrifuge the Spin Filter at 10,000 x g for 30 seconds at room temperature. 19. Discard the Spin Filter. The DNA in the 2 ml Collection Tube is now application ready. No further steps are required. We recommend storing DNA frozen (-20 to -80 C). PowerClean DNA Solution 7 does not contain EDTA. Note: If DNA degradation is a concern, sterile TE may also be used instead for elution of DNA from the Spin Filter. Thank you for choosing the PowerClean DNA Clean-Up. 8

9 Hints and Troubleshooting Guide Amount of DNA to Process This kit is designed to process up to 150 l of DNA (20 g maximum). For inquiries regarding the use of larger sample amounts, please contact technical support for suggestions. If DNA Does Not Amplify Make sure to check DNA yields by gel electrophoresis or spectrophotometer reading. Template DNA concentration could influence the outcome of PCR along with other the reaction conditions, enzyme activity, and copy number of the target sequence. If DNA does not amplify after altering the concentration of template DNA, please call our technical support for suggestions. Eluted DNA Sample Is Brown We have not observed any coloration in DNA isolated using the PowerClean DNA Clean-Up. If you observe coloration in your samples, please contact technical support for suggestions. Concentrating the DNA The final volume of eluted DNA will be up to 150 l depending on the amount of starting material. The DNA may be concentrated by adding 1/10 th volume of 5 M NaCl and inverting 3-5 times to mix. Next, add 200 l of 100% cold ethanol and mix. Centrifuge at 10,000 x g for 15 minutes at room temperature. Decant all liquid. Remove residual ethanol in a speed vac, dessicator, or ambient air. Resuspend precipitated DNA in sterile water or 10 mm Tris. DNA Floats Out of Well When Loaded on a Gel Residual PowerClean DNA Solution 6 remains in the final sample. Prevent this by being careful not to transfer liquid onto the bottom of the Spin Filter basket. Ethanol precipitation is the best way to remove residual PowerClean DNA Solution 6. (See Concentrating the DNA above) Storing DNA DNA is eluted in PowerClean DNA Solution 7 (10 mm Tris) and must be stored at -20 C to -80 C to prevent degradation. DNA can be eluted in TE but the EDTA may inhibit reactions such as PCR and automated sequencing. DNA may also be eluted with sterile DNA-Free PCR Grade Water (MO BIO Catalog# ). Technical Tips Visit MO BIO s The Culture Dish at for the latest in technical tips for frequently asked questions. Use this valuable resource to share your suggestions and optimization techniques for difficult or problematic samples. 9

10 Contact Information Technical Support: Phone MO BIO Laboratories, Inc. Toll Free , or Fax: Mail: MO BIO Laboratories, Inc, 2746 Loker Ave West, Carlsbad, CA Ordering Information: Direct: Phone MO BIO Laboratories, Inc. Toll Free , or Fax: Mail: MO BIO Laboratories, Inc, 2746 Loker Ave West, Carlsbad, CA For the distributor nearest you, visit our web site at 10

11 Other Quality Products Available from MO BIO Laboratories, Inc. For more product and detailed information go to to request a catalog. DNA Purification and Gel Extraction Catalog No. Quantity RNA Isolation Continued Catalog No. Quantity PowerClean DNA Clean-Up UltraClean Tissue & Cells RNA Isolation UltraClean 15 DNA Purification preps UltraClean Plant RNA Isolation preps UltraClean PCR Clean-Up Genomic DNA Isolation Catalog No. Quantity UltraClean -htp 96 Well PCR Clean- Up x 96 preps 12 x 96 preps PowerBiofilm DNA Isolation UltraClean GelSpin DNA Extraction Plasmid DNA Isolation Catalog No. Quantity UltraClean 6 Minute Mini Plasmid Prep UltraClean Standard Mini Plasmid Prep PowerFood Microbial DNA Isolation BiOstic Bacteremia DNA Isolation BiOstic FFPE Tissue DNA Isolation BiOstic Paraffin Removal Reagent x 25 ml UltraClean -htp 96 Well Plasmid Prep x 96 preps PowerMax Soil DNA Isolation preps x 96 preps UltraClean Midi Plasmid Prep preps PowerSoil DNA Isolation UltraClean Maxi Plasmid Prep preps 20 preps PowerSoil -htp 96 Well Soil DNA Isolation x 96 preps 12 x 96 preps UltraClean Endotoxin-Free Mini Plasmid Prep UltraClean Soil DNA Isolation UltraClean Endotoxin-Free Midi Plasmid Prep preps UltraClean -htp 96 Well Soil DNA Isolation x 96 preps 12 x 96 preps UltraClean Endotoxin-Free Maxi preps UltraClean Mega Soil DNA Isolation preps Plasmid Prep UltraClean Endotoxin Removal kit PowerClean DNA Clean-Up UltraClean Endotoxin-Free Ethanol Precipitation kit UltraClean Fecal DNA Isolation UltraClean Endotoxin Removal ml PowerMicrobial Midi DNA Isolation preps Reagent Endotoxin-Free Sodium Chloride ml PowerMicrobial Maxi DNA Isolation preps Endotoxin-Free Centrifuge Tubes each/2 ml UltraClean Microbial DNA Isolation each/15 ml 25 each/50 ml RNA Isolation Catalog No. Quantity UltraClean -htp 96 Well Microbial DNA Isolation x 96 preps 12 x 96 preps PowerBiofilm RNA Isolation PowerPlant DNA Isolation LifeGuard Soil Stabilization Solution On-Spin Column DNase I (RNase- Free) BiOstic Stabilized Blood RNA Isolation BiOstic Blood Total RNA Isolation RNA PowerSoil DNA Elution Accessory RNA PowerSoil Total RNA Isolation UltraClean Microbial RNA Isolation 10 ml 100 ml 1 L 7.5 L UltraClean Plant DNA Isolation UltraClean -htp 96 Well Plant DNA Isolation preps UltraClean Tissue & Cells DNA Isolation preps UltraClean -htp 96 Well Tissue DNA Isolation preps UltraClean Blood DNA Isolation (Non-Spin) preps UltraClean Blood DNA Isolation (Processes 1,000 ml of Blood) UltraClean Blood DNA Isolation Plus RNase (Processes 1,000 ml of Blood) x 96 preps 12 x 96 preps x 96 preps x 96 preps kit kit 11

12 Other Quality Products Available from MO BIO Laboratories, Inc. For more product and detailed information go to to request a catalog. Genomic DNA Isolation Continued Catalog No. Quantity UltraClean BloodSpin DNA Isolation UltraClean -htp 96 Well BloodSpin x 96 preps DNA Isolation x 96 preps UltraClean Forensic DNA Isolation isolations isolations PowerWater DNA Isolation NF RapidWater DNA Isolation UltraClean Water DNA Isolation (0.45µm filters) UltraClean Water DNA Isolation (0.22 µm filters) UltraClean Water DNA Isolation (No filters) NF NF NF NF NF (No filters) (0.22 μm) (0.45 μm) (No filters) (0.22 μm) (0.45 μm) (No filters) (0.22 μm) (0.45 μm) (No filters) (0.22 μm) (0.45 μm) 10 preps 25 preps 10 preps 25 preps 10 preps 25 preps Microbiological Culture Media Catalog No. Quantity TB DRY Powder Growth Media LB Broth Powder Growth Media, ph LB Agar Powder Growth Media, ph LB Broth (Lennox) Powder Growth Media, ph 7 LB Agar (Lennox) Powder Growth Media, ph 7 Soybean-Casein Digest Medium (TSB), USP Soybean-Casein Digest Agar Medium (TSA), USP Yeast Extract Tryptone Agar, Bacteriological Grade Other Reagents and Lab Accessories Catalog No. Quantity 20 bp DNA Ladder µg 100 bp DNA Ladder µg 1 kb DNA Ladder µg UltraClean Agarose, Molecular Biology Grade UltraClean MS-8 Agarose UltraClean Forensic Agarose UltraClean Low Melt Agarose UltraClean Low Melt Sieve Agarose Ethidium Bromide Solution Ethidium Bromide Destaining Tea Bags Bromophenol Blue Gel Loading Buffer Bromophenol Blue/Xylene Cyanol Gel Loading Buffer 50 g 100 g 50 g 100 g 50 g 100 g 50 g 100 g 50 g 100 g 1 ml 10 ml bags TAE Buffer, 50X (Tris-acetate-EDTA) TBE Buffer, 10X (Tris-borate-EDTA) RNase-Free Gloves 1555-XS 1555-S 1555-M 1555-L UltraClean Lab Cleaner KAPA PROBE FAST qpcr s KAPA SYBR FAST Universal 2X qpcr Master Mix KAPA2G Robust HotStart ReadyMix ml 5 x 1 ml 1 ml 5 x 1 ml 100 ml 500 ml 1 liter 100 ml 500 ml 1 liter bag of 100 bag of 100 bag of 100 bag of ml squeeze bottle 500 ml spray bottle 1 liter bottle 100 reactions 500 reactions 1000 reactions 100 reactions 500 reactions 1000 reactions 100 reactions 500 reactions 12

13 Other Quality Products Available from MO BIO Laboratories, Inc. For more product and detailed information go to to request a catalog. Other Reagents and Lab Accessories Continued Catalog No. Quantity KAPA HiFi HotStart ReadyMix reactions reactions KAPA2G FAST HotStart DNA reactions Polymerase with dntps reactions reactions KAPA2G FAST HotStart ReadyMix reactions KAPA Long Range HotStart DNA Polymerase with dntps reactions 100 reactions 250 reactions 500 reactions Instrumentation and Accessories Continued Catalog No. Quantity Glass Bead Tubes, 0.5 mm bead Glass Bead Tubes, 0.1 mm bead Metal Bead Tubes, 2.38 mm bead 2.0 ml Tough Tubes with Cap KAPA Taq Polymerase ReadyMix reactions Carbide Bead Tubes, 0.25 mm x 0.5 ml OmniTaq DNA Polymerase Enzyme reactions (10 U/µl) Garnet Bead Tubes, 0.15 mm x 0.5 ml OmniTaq DNA Polymerase 2x Master Mix reactions (5 x 1.25 Garnet Bead Tubes, 0.70 mm x 2 ml Omni KlenTaq DNA Polymerase Enzyme Omni KlenTaq DNA Polymerase 2x Master Mix DNase (RNase-Free) Proteinase K Ribonuclease A (25 mg/ml) PCR Water Molecular Biology Grade Water DEPC Treated Water Endotoxin-Free Water ml/tube) reactions (25 U/µl) reactions (5 x 1.25 ml/tube) 5 mg 2500 units 100 mg 2 ml (20 mg/ml) 1 ml 5 ml 1 ml 5 x 1 ml 10 x 1 ml 10 ml bottle 200 ml 5 x 200 ml 200 ml 5 x 200 ml 10 ml 50 ml 100 ml 500 ml Garnet + ¼ Ceramic 15 ml Bead Tubes, 0.70 mm Garnet + ¼ Ceramic 50 ml Bead Tubes, 0.70 mm ` Glass 15 ml Bead Tubes, 0.1 mm Glass 50 ml Bead Tubes, 0.1 mm Glass 15 ml Bead Tubes, 1.0 mm Ceramic 15 ml Bead Tubes, 1.4 mm Ceramic 50 ml Bead Tubes, 1.4 mm Metal 50 ml Bead Tubes, 2.38 mm PowerMix 15 ml Bead Tubes PowerMix 50 ml Bead Tubes Instrumentation and Accessories Catalog No. Quantity PowerLyzer 24 Bench Top Bead unit 2 ml Collection Tubes T Based Homogenizer (110/220V) T T PowerLyzer Tube Holder unit 2 ml Screw Cap Tubes E 200 & caps PowerLyzer Tube Holder Stand unit 15 ml Collection Tubes T 25 PowerVac Mini System unit ml Centrifuge Tubes T 25 adapters PowerVac Manifold unit Spin Filters (in 1.9 ml ) SF SF SF 50 filters 100 filters 250 filters PowerVac Mini Spin Filter Adapters adapters 20 adapters Endotoxin-Free Centrifuge Tubes each/2 ml 50 each/15 ml 25 each/50 ml Ceramic Bead Tubes, 1.4 mm bead 15 ml Midi Spin Filters SF 25 spin filters Ceramic Bead Tubes, 2.8 mm bead

14 Other Quality Products Available from MO BIO Laboratories, Inc. For more product and detailed information go to to request a catalog. Instrumentation and Accessories Continued Catalog No. Quantity Instrumentation and Accessories Continued Catalog No. Quantity Vortex-Genie 2 Vortex (120V) V 1 unit Mini Horizontal Gel System each Vortex-Genie 2 Vortex (220V) V unit Mini Horizontal Gel Caster, 3 place each Vortex Adapter, holds 12 ( ml) V1 1 unit Mini Horizontal Gel Tray each Vortex Adapter, holds 6 (5 ml) V1-5 1 unit Polycarbonate Single-sided Comb mm x 3 well 1 mm x 8 well 1 mm x 10 well 1 mm x 12 well Vortex Adapter, holds 4 (15 ml) V unit Polycarbonate Dual-sided Comb mm x 8 well/16 well 1 mm x 10 well/14 well 2 mm x 8 well/16 well 2 mm x 10 well/14 well Vortex Adapter, holds 2 (50 ml) V unit Teflon Single-sided Comb mm x 3 well 1 mm x 8 well 1 mm x 10 well 1 mm x 12 well Vortex Adapter, holds 24 ( ml) V unit Teflon Dual-sided Comb BagMixer 400 VW unit Power Supply w/timer, (120V) unit BagFilter 400 P Box of 500 Power Supply w/timer, (220V) unit BagPage Box of Well Plate Shaker (120V) unit mm x 8 well/16 well 1 mm x 10 well/14 well 2 mm x 8 well/16 well 2 mm x 10 well/14 well Whirl-Pak Collection Bag, Small (532 ml) Whirl-Pak Collection Bag, Medium (1,627 ml) Whirl-Pak Collection Bag, Large (3,637 ml) Whirl-Pak Stand up Bag, Small (118 ml) Whirl-Pak Stand up Bag, Medium (532 ml) Whirl-Pak Stand up Bag, Large (1,242 ml) Whirl-Pak Stand up Bag, Extra- Large (2,041 ml) bags 96 Well Plate Shaker (220V) unit bags Plate Adapter Set set bags Vacuum Pump (120V) unit bags Vacuum Pump (220V) unit bags UltraVac Manifold unit bags bags Whirl-Pak Scoop Bag, 60 ml bags Anti-Static Funnels, Micro Pack of 96 Anti-Static Funnels, Small Pack of 50 Anti-Static Funnels, Medium Pack of 50 Anti-Static Funnels, Large Pack of 20 14