: GA-HF-14/ GA-HFB-14
|
|
- Geraldine Page
- 5 years ago
- Views:
Transcription
1 Grace Electron Corp. Processing Guide Halogen Free Material Laminate/ Prepreg : GA-HF-14/ GA-HFB-14 Grace Electron Corp. Tech. & QA Dept. Revision 2009/5/18 Page 1 of Group
2 Grace Declaration: The parameters and the processing guide contained in this document were developed through in-house evaluation result and field experience, and PCB makers should need some necessary additional adjustment for the parameters by themselves, to make sure that the parameters could meet the actual manufacture quality requirement. Grace could provide technical support when customers using any type of Grace products. Part1 Prepreg storage Prepreg storage suggestion (Vacuum package unbroken): Condition A: 23, 50% RH for three months. Condition B: lower than 5 for 6 months from date of manufacture. Prepreg usage suggestion: 1.1 Upon receipt, all prepreg should be immediately moved to a both temperature and humidity controlled environment. A FIFO (first-in-first-out) inventory management system should be used. 1.2 Prepreg has a lower lifetime; exposure in the air may have its properties degrade. Hold time after shearing had better no more than 24 hours. The remain prepreg must be vacuum packaged, and a remove moisture treatment is necessary when the second time use. 1.3 In shearing process, all prepreg panel sheets should be kept cleaning. Note: 1. Grace suggests the prepreg must be used as soon as possible from after shearing to lamination. 2. Prepreg exceeding shelf life must be retested and re-certified to agree upon specifications. Revision 2009/5/18 Page 2 of Group
3 Part2 Laminate storage Laminate storage suggestion (Package unbroken): 2.1 Upon receipt, all laminate should be immediately moved to a catalytic environment such as UV light or excessive radiation. 2.2 All laminate should be used as soon as possible to avoid oxides on the surface. Laminate baking suggestion: In order to holding the dimensional stability of the laminate after shearing into panel sheets, the baking is recommendation. Materials GA-HF-14 Temperature 140 Time 2~4 hrs Note: When the storage of laminate is over one year, the properties must be retested and re-certified to agree upon specifications. Part3 Lamination process 3.1 Black or brown oxide treatment Chemistry suitability: Both chemistry of black or brown oxide treatment are suitable After oxide treatment, the baking panel sheets is recommended and should no scratch or impurity contain on the surface. Please dry before lamination process for reducing moisture if inner layer boards absorb moisture. Revision 2009/5/18 Page 3 of Group
4 Peel strength of copper foil oxide treatment side: For the fillers added materials, the higher peel strength of copper foil oxide treatment side and the better performance of the PCB board in the reliability evaluation. Above 4.0 Lb/in is recommended, especially for the PCB board used into Lead Free solder process The board holds time had better no more than 12 hours after oxide treatment process. Note: Grace suggests the board must be used as soon as possible from after oxide treatment to lamination. 3.2 Lamination suggestion Prepreg and core prepare: The PCB makers use the prepreg and core must be the same kind of product and from the same suppliers. Prepreg lamination condition: Materials Heating rate Curing condition GA-HF-14 Heating rate: 1.5~2.5 /min (Material temperature from 80 ~140 ) 170 ~180, over 40min Note: All values mentioned above are just for reference, the parameters can be modified depend upon board design, machine as well as other factors. Revision 2009/5/18 Page 4 of Group
5 Part4 Drilling process As the greater modulus strength of epoxy material which is filler added, the drilling parameters should be well adjustment to avoid excessive roughness after drilling and meet the requirement of the quality. Drilling parameters suggestion: Diameter (mm) Speed (KRPM) Infeed (IPM) Chipload (µm/rev) Max. Hit Ø < ~ < Ø < ~2000 Note: All values mentioned above are just for reference, the parameters can be modified depend upon different materials, layer counts, thickness, inner layer copper thickness as well as other factors. Baking condition after drilling: Grace recommends to baking the laminates just after drilling to releasing residual stress in the laminates. Materials GA-HF-14 Temperature 140 Time 2~3 hrs Note: In baking process, all laminate panel sheets should be kept cleaning. Part5 Desmear and weight loss The parameters of desmear should be suitable adjustment depend upon different materials characteristics to make sure the epoxy smear should be cleaned. The PTH back light should be over 8 grades. Revision 2009/5/18 Page 5 of Group
6 Weight loss suggestion: Materials Weight loss (mg/dm 2 ) GA-HF-14 25~35 Part6 Routing As the greater modulus strength of epoxy material which is filler added, the routing fabrication is recommended instead of punching fabrication to avoid excessive fracturing and white edge on the PCB board. Routing parameters suggestion: Diameter (mm) Speed (KRPM) Infeed (IPM) <1.0 45~50 20~ Ø <1.4 40~45 20~ Ø <2.0 25~40 20~ Ø <2.6 20~27 30~ Ø 15~18 30~60 Note : All values mentioned above are just for reference, the routing and v-cut parameters can be modified depend upon layer counts, thickness, different materials characteristics as well as other factors. Revision 2009/5/18 Page 6 of Group
7 Part7 Solder mask rework The chemical resistance of fillers added material is inferior to that of standard FR4. In the process of solder mask rework, the risk of blister and weave exposure may increase easily. The parameters (such as dwelling time, temperature, rework times ) of rework process should be modified dependent on PCB stack-up, outer layer butter coat thickness and different materials characteristics. Part8 Package and shipment of PCB The PCB should be in a moisture proof packing with desiccant and avoid any physical damages during transport. If PCB absorbs moisture during transport, the risk of delamination might occur in SMT reflow assembly or another heating process. Please dry it more than 2 hours at 120. Revision 2009/5/18 Page 7 of Group
: GA-170-LE/ GA-170B-LE
Grace Electron Corp. Processing Guide Phenolic Cured Material Laminate/ Prepreg : GA-170-LE/ GA-170B-LE Grace Electron Corp. Tech. & QA Dept. Revision 2010/3/30 Page 1 of 7 @2010Grace Group Grace Declaration:
More information: GA-170-LL/ GA-170B-LL
Grace Electron Corp. Processing Guide Phenolic Cured Material Laminate/ Prepreg : GA-170-LL/ GA-170B-LL Grace Electron Corp. Tech. & QA Dept. Revision 2010/6/14 Page 1 of 6 @2010Grace Group Grace Declaration:
More informationLow CTE / High Tg FR-4 with High Heat Resistance
Low CTE / High Tg FR-4 with High Heat Resistance Laminate: EM-827 Prepreg: EM-827B 1 Features Tg(DSC) > 170 Z direction CTE < 3.0% (50~260 ) High thermal degradation temperature: Td > 340 Excellent thermal
More informationNo Process Guidelines. Laminate R-5775 Prepreg R High Speed, Low Loss Multi-layer Materials
No.17062967 Process Guidelines Laminate R-5775 Prepreg R-5670 High Speed, Low Loss Multi-layer Materials No.17062967-1 General Material Storage Laminate should be stored flat in a cool dry environment.
More informationNo Process Guidelines. Laminate R-5785 Prepreg R High Speed, Low Loss Multi-layer Materials
No.17062968 Process Guidelines Laminate R-5785 Prepreg R-5680 High Speed, Low Loss Multi-layer Materials No.17062968-1 General Material Storage Laminate should be stored flat in a cool dry environment.
More informationI-Speed Processing Guide
I-Speed Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points that
More informationLEAD-FREE ASSEMBLY COMPATIBLE PWB FABRICATION AND ASSEMBLY PROCESSING GUIDELINES.
LEAD-FREE ASSEMBLY COMPATIBLE PWB FABRICATION AND ASSEMBLY PROCESSING GUIDELINES. TECHNICAL BULLETIN As the industry has moved to lead-free assembly processing, the performance demands on the lead free
More informationNo Process Guidelines. Laminate R-1755C Prepreg R-1650C. High Reliability Glass Epoxy Multi-layer Materials
No.17062957 Process Guidelines Laminate R-1755C Prepreg R-1650C High Reliability Glass Epoxy Multi-layer Materials No.17062957-1 General Material Storage R-1650C laminate and R-1650C prepreg is the same
More informationRO4835T Core/RO4450T Bonding Layers Multi-Layer Board Processing Guidelines
Fabrication Technical Articles Notes RO4835T Core/RO4450T Bonding Layers Multi-Layer Board Processing Guidelines These guidelines were developed to provide fabricators basic information on processing core
More informationI-Tera MT40 Processing Guide
I-Tera MT40 Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points
More informationIS410 Processing Guide
IS410 Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points that will
More informationFR408 Processing Guide
FR408 Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points that will
More informationNo Process Guidelines. Laminate R-5725 Prepreg R High Speed, Low Loss Multi-layer Materials
No.17062965 Process Guidelines Laminate R-5725 Prepreg R-5620 High Speed, Low Loss Multi-layer Materials No.17062965-1 General Material Storage R-5725 laminate and R-5620 prepreg is the same as our conventional
More informationFR402 Processing Guide
FR402 Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points that will
More informationDE104i Processing Guide
DE104i Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points that
More informationAstra MT77 Processing Guide
Astra MT77 Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points that
More informationFR408HR. Processing Guide. Part 1: Prepreg Storage and Handling. Part 2: Innerlayer Preparation. Dimensional Stability. Handling Suggestions
FR408HR Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points that
More informationFR408HR & FR408HRIS Processing Guide
FR408HR & FR408HRIS Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting
More informationPractical guidelines for PWB Moisture Sensitivity, Packaging and Handling. Mumtaz Y. Bora Peregrine Semiconductor San Diego, CA, USA
Practical guidelines for PWB Moisture Sensitivity, Packaging and Handling Mumtaz Y. Bora Peregrine Semiconductor San Diego, CA, USA Agenda and Overview Industry Standards for Moisture Sensitivity Packages
More informationIS620i Processing Guide
IS620i Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points that
More informationIS620i. Part 1: Prepreg Storage and Handling. Part 2: Innerlayer Preparation. appropriate environmental control.
IS620i The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points that will require further
More informationCorrective Action: 1. Determine type of nailhead, single sided nailheading or bidirectional
APPLICATION NOTES Drilling Defects: Causes and Solutions Rev April 3 2012 Nailheading: Nailheading is the distortion of the copper inner layer at the hole wall, this distortion takes the form of a Nailhead.
More informationVT-45PP VT-47PP VT-447PP
& Prepreg General Information Ventec provides a series of and Prepregs with different glass style and resin content. These products have good bonding and thermal performance in applications of heat sink
More informationAnnular Ring and Feature Clearances. Track to Feature Clearances
Hi-Tech Corporation Technical Capabilities Annular Ring and Feature Clearances Outer Value layer min (mm) A 75 B 125 C 150 Inner Value layer min (mm) A 100 B 150 C 150 Track to Feature Clearances Outer
More informationAxiom Electronics LLC
1 of 8 1.0 PURPOSE and SCOPE This document defines Axiom s requirements for printed circuit board (PCB) fabrication, handling, and storage. Industry standards are referenced where appropriate. This document
More informationHow Printed Circuit Boards are Made. Todd Henninger Field Applications Engineer Midwest Region
PCB 101: How Printed Circuit Boards are Made Todd Henninger Field Applications Engineer Midwest Region Tooling PRE-PRODUCTION ENGINEERING (Tooling) Design Data Package CAD Data (ODB++ or Gerber 274x format)
More informationCompany Overview Markets Products- Capabilities
Company Overview Markets Products- Capabilities A Simpler way for PCB production. www.purepcb.co.uk What can Pure do for you? From 1 off Circuit upward, No MOQ/MOV High Mix Production Focus. Fast Turn
More informationMCPCB Material (Heat sync)
MCPCB Material (Heat sync) NIPPON RIKA KOGYOSHO CO.,LTD Feb Metal Base CCL (Heat sync) Metal Base CCL (Heat sync) Copper Foil FR-4 High Performance Epoxy Metal Base Glass Cloth + Epoxy Etching Etching
More informationNew Developments in PCB Laminates. Dean Hattula, John Coonrod Rogers Corporation Advanced Circuit Materials Division
New Developments in PCB Laminates Dean Hattula, John Coonrod Rogers Corporation Advanced Circuit Materials Division Overview PCB laminate properties Thermal stability Electrical performance Summary PCB
More informationTEST REPORT (Self-Tested Data)
TEST REPORT (Self-Tested Data) CLIENT: IPC Validation Services 3000 Lakeside Drive Suite 105N Bannockburn, IL 60015 USA Attention: Mr. Randy Cherry +1-847-597-5606 TEST ITEMS: Peel Strength, Volume Resistivity,
More informationPRELIMINARY. RO4533, RO4534, AND RO4535 Laminates. Preliminary Data Sheet Antenna Grade Laminates
Advanced Circuit Materials Rogers Antenna Grade Materials RO4500 Series Cost Performance Antenna Grade Laminates A new line of cost/performance materials from Rogers Corporation. These laminates are specifi
More informationFR406N Processing Guide
FR406N Processing Guide The processing guidelines contained in this document were developed through in-house testing and field experience. However, they should be considered to be starting points that
More informationA Novel Material for High Layer Count and High Reliability Printed Circuit Boards
A Novel Material for High Layer Count and High Reliability Printed Circuit Boards Jie Wan, Junqi Tang, Xianping Zeng Shengyi Technology Co., Ltd. No.5 Western Industry Road, North Industry District SSL
More informationQuestion: Are RO4000 materials compatible with lead-free processes? Answer:
Question: Are RO4 materials compatible with lead-free processes? Answer: RO4 cores and prepregs are among the most temperature stable products available. They easily meet or exceed all expectations for
More informationATS Document Cover Page
221-008 Item Rev Status: RELEASED printed 9/20/2017 2:27:42 PM by Les Deenin ATS: OPERATIN PROCEDURE ATS Document Cover Page Responsible Department: Supply Chain This copy is uncontrolled unless otherwise
More informationN9000 PTFE Processing Guidelines
N9000 PTFE Substrates The Park/Nelco (previously known as Metclad) NY, NX, and NH families of RF and Microwave materials are woven fiberglass/ptfe composites for use as printed-circuit substrates. The
More informationICDs (InterConnect Defects) What are they? Where do they come from? How can we make them go away? Doug Trobough Suixin Zhang
ICDs (InterConnect Defects) What are they? Where do they come from? How can we make them go away? Doug Trobough Suixin Zhang Definition of ICD ICDs are any defect that occurs adjacent to the innerlayer
More informationBasic 4-layer manufacturing process
Basic 4-layer manufacturing process Erwin Lemmens - AQC BV 7-11 D&E BE / Booth 1 8-11 D&E NL / Booth 18 AQC (Advanced Quality Control) BV Supplying pcb s, flex, flex-rigids, aluminium, etc - standard and
More informationFABRICATING HIGH CURRENT, HEAVY COPPER PCBS
Royal Circuit Solutions 21 Hamilton Ct, Hollister, CA 95023 (831) 636-7728 www.royalcircuits.com FABRICATING HIGH CURRENT, HEAVY COPPER PCBS INTRODUCTION All printed circuit boards (PCBs) carry current
More informationCer-10. General Processing Guidelines
Cer-10 General Processing Guidelines Petersburgh, NY Tel: 800-833-1805 Fax: 518-658-3988 Europe Tel: +353-44-38300 Fax: +353-44-44369 Asia Tel: +82-31-704-1858 Fax: +82-31-704-1857 www.taconic-add.com
More informationMoisture Measurements in PCBs and Impact of Design on Desorption Behaviour
Moisture Measurements in PCBs and Impact of Design on Desorption Behaviour Chris Hunt, Owen Thomas & Martin Wickham National Physical Laboratory Teddington, UK Abstract High levels of residual moisture
More informationDeepen your knowledge
FLEX & RIGID-FLEX PRINTED CIRCUIT BOARDS Deepen your knowledge What are Flex & Rigid-flex Printed Circuit Boards? What are their similarities and differences? Their capabilities? And the design rules.
More informationNP-180R NAN YA PLASTICS CORPORATION ELECTRONIC MATERIALS DIVISION. COPPER CLAD LAMINATE DEPARTMENT NO TUNG HWA N. ROAD, TAIPEI, TAIWAN.
New: 2014/04/30 flame retardant copper clad laminate NP-180R High Tg 175 (DSC) Excellent dimensional stability through-hole reliability Excellent electrical, chemical and heat resistance properties IPC-4101C
More informationIBM Laminate Study Group
IBM Laminate Study Group Lead-Free Laminate Robustness Brett Krull, Dept FM2 Nov 18, 2009 Agenda Introductions Laminate Robustness Background Qualification Methods Contributing Factors Past Work on Laminate
More informationMultek s lead free compatible and compliant material selection February 01, 2006
Multek s lead free compatible and compliant material selection Helmut.Kroener@de.multek.com +49 7 463 543 February 0, 2006 Overview I. Introduction II. Project setup III. Tested materials IV. Test vehicle
More informationRF-43. General Processing Guidelines
RF-43 General Processing Guidelines Petersburgh, NY Tel: 800-833-1805 Fax: 518-658-3988 Europe Tel: +353-44-38300 Fax: +353-44-44369 Asia Tel: +82-31-704-1858 Fax: +82-31-704-1857 www.taconic-add.com www.taconic.co.kr
More informationIntroduction Conductors. Supply Planes. Dielectric. Vias PCB Manufacturing Process Electronic Assembly Manufacturing Process
PCBs/Overview Printed Circuit Boards (PCB) Introduction Conductors. Supply Planes. Dielectric. Vias PCB Manufacturing Process Electronic Assembly Manufacturing Process 29/09/2005 EE6471 (KR) 263 PCBs/Overview
More informationInterconnection Reliability of HDI Printed Wiring Boards
Presented in the ECWC 10 Conference at IPC Printed Circuits Expo, SMEMA Council APEX and Designers Summit 05 Interconnection Reliability of HDI Printed Wiring Boards Tatsuo Suzuki Nec Toppan Circuit Solutions,
More informationPCB Fabrication Specification
Original Author: Steve Babiuch Process Owner: Steve Babiuch Page 2 of 8 1.0 Purpose This specification establishes the NEO Tech fabrication requirements for printed circuit boards. The order of precedence
More informationIPC-6012DA with Amendment 1. Automotive Applications Addendum to IPC-6012D Qualification and Performance Specification for Rigid Printed Boards
A with Amendment 1 Automotive Applications Addendum to Qualification and Performance Specification for Rigid s FINAL DRAFT FOR INDUSTRY REVIEW MAY 2018 0.1 Scope This addendum provides requirements to
More informationFlex and Rigid flex boards. 02/2013 Written by Zreik Anan
Flex and Rigid flex boards 02/2013 Written by Zreik Anan Advantages Better Reliability Dynamic flexing Replace cables (Static Flexing) Simplify assembly process Less rework Saves money Materials Flex clad
More informationUL PCB Recognition what is it & why do you need to know about it
UL PCB Recognition what is it & why do you need to know about it Presented by Emma Hudson NCAB Customer Event March 2015 UL and the UL logo are trademarks of UL LLC 2015 Agenda What is UL and what are
More informationQualification and Performance Specification for High Frequency (Microwave) Printed Boards
Qualification and Performance Specification for High Frequency (Microwave) Printed Boards Developed by the High Speed/High Frequency Board Performance Subcommittee (D-22) of the High Speed/High Frequency
More informationLead Free Assembly: A Practical Tool For Laminate Materials Selection
Lead Free Assembly: A Practical Tool For Laminate Materials Selection Erik J. Bergum David Humby Isola Abstract: The impending European RoHS legislation, restricting the use of lead containing solders,
More informationYash Sutariya President
Yash Sutariya President Saturn Electronics Corporation Glory Faith North America Saturn Flex Systems Key Inputs to PCB Reliability Backbone Fabrication Processes Multilayer Press Via Drilling Copper Through
More informationSpecification for Base Materials for Rigid and Multilayer Printed Boards
ASSOCIATION CONNECTING ELECTRONICS INDUSTRIES Specification for Base Materials for Rigid and Multilayer Printed Boards Developed by the Laminate/Prepreg Materials Subcommittee (3-11) of the Printed Board
More informationFeatures. Applications
ASMB-MTC1-A3A2 PLCC-4 Tricolor Black Body LED Data Sheet Description This family of SMT LEDs are in PLCC-4 package. A wide viewing angle together with the built in reflector drives up the intensity of
More informationPEC (Printed Electronic Circuit) process for LED interconnection
PEC (Printed Electronic Circuit) process for LED interconnection Higher wattage LED s/ power components or their placement in higher densities, requires a larger dissipation of heat in a more effective
More informationStackup Planning, Part 1
by Barry Olney coulmn BEYOND DESIGN Stackup Planning, Part 1 The PCB substrate that physically supports the components, links them together via highspeed interconnects and also distributes highcurrent
More informationCharacterizing the Lead-Free Impact on PCB Pad Craters
Characterizing the Lead-Free Impact on PCB Pad Craters Brian Roggeman and Wayne Jones Advanced Process Lab Universal Instruments Corp. Binghamton, NY 13902 Abstract Pad cratering in Printed Circuit Boards
More informationRO3000 and RO3200 Series High Frequency Laminates STRIPLINE AND MULTILAYER CIRCUITS
Fabrication Notes RO3000 and RO3200 Series High Frequency Laminates STRIPLINE AND MULTILAYER CIRCUITS MATERIAL DESCRIPTION: RO3003, RO3006 and RO3010 copper clad laminates are filled PTFE composites offering
More informationB-IS400 IS420/3 IS400 IS420 PCL370HR. Temperature resistant mid and high T g - base materials with low z-axis expansion CAF ENHANCED
J B-IS4 IS42/3 IS4 IS42 PCL37HR Temperature resistant mid and high T g - base materials with low z-axis expansion CAF ENHANCED Temperature-resistant base materials with low z-axis expansion IS4, IS42 and
More informationGORE SMT EMI Gaskets and Grounding Pads
GORE SMT EMI Gaskets and Design Guide SMT EMI Gaskets and GORE Introduction GORE SMT EMI Gaskets and, Supersoft Series solves many grounding and shielding challenges in automotive electronics by delivering
More informationIPC-AJ-820A Assembly and Joining Handbook. The How and Why of All Things PCB & PCA
IPC-AJ-820A Assembly and Joining Handbook The How and Why of All Things PCB & PCA 1 Scope To provide guidelines and supporting info for the mfg of electronic equipment To explain the HOW TO and WHY Discussions
More informationGORE SMT EMI Gaskets and Grounding Pads
GORE SMT EMI Gaskets and Design Guide SMT EMI Gaskets and GORE Introduction GORE SMT EMI Gaskets and, Supersoft Series solves many grounding and shielding challenges in automotive electronics by delivering
More informationInterconnection Evaluation Technology for Printed Wiring Boards
Interconnection Evaluation Technology for Printed Wiring Boards Mitsuhiko Sugane Yoshihiro Morita (Manuscript received December 28, 2009) As a developer of world-class products including server and network
More informationGold Circuit Electronics
Gold Circuit Electronics Materials Development Focus November 19th, 2009 IBM Symposium Effective characterization and introduction of new printed circuit board materials into mass production is a need.
More informationHow to select PCB materials for highfrequency
How to select PCB materials for highfrequency apps Find out how to simplify that choice when striving for the best tradeoff between ease of fabrication and best electrical performance. By John Coonrod
More informationFreescale Semiconductor Tape Ball Grid Array (TBGA) Overview
Freescale Semiconductor Tape Ball Grid Array (TBGA) Overview Revision 0 2006 Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the
More informationVerifying The Reliability Of Connections In HDI PWBs
Verifying The Reliability Of Connections In HDI PWBs The stacking of via holes is used effectively in the development of high density circuits on build-up printed wiring boards (PWBs). However, when micro
More informationLL081RR1-62P1-OY1 Technical data sheet
LL081RR1-62P1-OY1 Technical data sheet Customer : Conrad Supplier : LG Display, Ltd. Issued date : Oct. 25, 2016 Product : OLED panel Development Team Production Team QA Team Approval Issue & revision
More informationEHP-AX08EL/LM01H-P01/2832/Y/K31
Data Sheet Features Feature of the device: Small package with high efficiency Typical color temperature: 3050 K. Typical view angle: 140 Typical light flux output: 80 lm @ 350mA. ESD protection. Soldering
More informationEHP-AX08EL/GT01H-P01/5670/Y/K42
Data Sheet Features Feature of the device: Small package with high efficiency Typical color temperature: 6300 K. Typical view angle: 140 Typical light flux output: 100 lm @ 350mA ESD protection. Soldering
More informationEHP-AX08EL/GT01H-P01/5670/Y/K42
Data Sheet Features Feature of the device: Small package with high efficiency Typical color temperature: 6300 K. Typical view angle: 140 Typical light flux output: 100 lm @ 350mA ESD protection. Soldering
More informationPart One Introduction
j1 Part One Introduction Evolvable Designs of Experiments: Applications for Circuits. Octavian Iordache Copyright Ó 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim ISBN: 978-3-527-32424-8 j3 1 Printed
More information!"#$#%&#'(() ) **+,-./01)2-,-.3)456,1) /0! **)
!"#$#%&#'(() ) **+,-./01)2-,-.3)456,1) /0!7.5853-09**) B 2 IT is a Toshiba Process Technology 1. Conductive Ag bumps are printed on a sheet of Cu foil. 2. Prepreg is pierced through by the bumps 3. Another
More informationTechnology HF-Printed Circuits Rev For latest information please visit
Options and Characteristics Online calculation On explicit enquiry Quantity 1 piece up to 0,4m² total area from 1 piece to mass production Layer quantity 1 to 2 layers Up to 8 layers Material thickness
More informationLow Dielectric Constant 3.9. RoHS/WEEE compliant. SMT Board Designs using LCCC s or other low expansion chip carriers (See Figure 1)
WOVEN KEVLAR REINFORCED LAMINATE AND PREPREG is a woven Kevlar aramid fiber reinforced multifunctional epoxy laminate and prepreg system engineered to provide in-plane CTE values as low as 6 ppm/ C for
More informationReliable Plated Through-Via Design and Fabrication. Cheryl Tulkoff DfR Solutions
Reliable Plated Through-Via Design and Fabrication Cheryl Tulkoff DfR Solutions ctulkoff@dfrsolutions.com 5129138624 What is a Plated Through Via? A plated through via (PTV) is an interconnect within a
More informationMaterials for High-Reliability Applications: All IPC-4101-Grouped Materials are not Created Equal
they have arrived! f e a t u r e n e w a d v a n c e d p c b m a t e r i a l s Materials for High-Reliability Applications: All IPC-4101-Grouped Materials are not Created Equal By Yash Sutariya Saturn
More informationAn Assessment of the Impact of Lead-Free Assembly Processes on Base Material and PCB Reliability
An Assessment of the Impact of Lead-Free Assembly Processes on Base Material and PCB Reliability Edward Kelley Isola Abstract Environmental regulations are forcing the elimination of lead (Pb) from electronic
More informationFeatures. Applications
ASMT-YTB7-AA2 Tricolor PLCC6 Black Surface LED Data Sheet Description This family of SMT LEDs packaged in the form of PLCC-6 with separate heat path for each LED dice, enabling it to be driven at higher
More informationThe Anatomy of a PCB SINGLE-SIDED BOARD
Published on Online Documentation for Altium Products (https://www.altium.com/documentation) 主页 > The Board Using Altium Documentation Modified by Jason Howie on Apr 11, 2017 Open up just about any electronic
More informationProcess & Capability Manual (Vol )
Process & Capability Manual (Vol. 12-2015) Seite 1 von 13 1 CHAPTER OVERVIEW 1 CHAPTER OVERVIEW... 2 2 MICROCIRTEC A SHORT PROFILE... 3 2.1 WHO WE ARE... 3 2.2 OBJECTIVES & MARKETS... 3 2.3 DECLARATION
More informationc/bach, 2-B Pol. Ind Foinvasa Montcada i Reixac (Barcelona) SPAIN Tel FAX
1- What is 2- How does it work? 3- How do we make it? 4- Applications 5- Processing? WHAT IS? Thick aluminium based substrate, cladded in ED copper foil. Designed for an effective thermal dissipation and
More informationTechnology Aluminium-IMS-PCBs Rev For latest information please visit
Options and Characteristics Online calculation On explicit enquiry Quantity 1 piece up to 1,0² total area from 1 piece to mass production Layer quantity 1- and 2-layers up to 6 layers Material thickness
More informationHigh Frequency Circuit Materials Attributes John Coonrod, Rogers Corporation
High Frequency Circuit Materials Attributes John Coonrod, Rogers Corporation Specialty high frequency circuit materials have been used in the PCB industry for decades and for many different reasons. There
More informationVisit
Effectiveness of Baking to Remove Moisture from Between PCB Ground Planes Martin Wickham & Owen Thomas 18 th March 2014 1 Your Delegate Webinar Control Panel Open and close your panel Full screen view
More informationWhite Paper. Discussion on Cracking/Separation in Filled Vias. By: Nathan Blattau, PhD
White Paper Discussion on Cracking/Separation in Filled Vias By: Nathan Blattau, PhD Introduction The Knadle PTH life curve" has been used for over 15 years to characterize new materials or PTH structures,
More informationTrends and Developments
Trends and Developments Monique Mayr Monique.Mayr@eu.panasonic.com European R&M Group Panasonic Corporation Electronic Material Business Division Weitere Informationen finden Sie auch auf: http://www3.panasonic.biz/em/pcbm/en/index.html
More informationManufacturing Capacity
Capability List Manufacturing Capacity QTA & Prototype Layer : 1L ~32 L Impedance Board Ball Grid Array ( BGA ) Blind/ Buried Via Micro Via ( Laser Drilling) Flex /Rigid Flexible PCB Series Orders Layer
More informationVia Formation Process for Smooth Copper Wiring on Insulation Layer with Adhesion Layer
Sasaki and Tani: Via Formation Process for Smooth Copper Wiring (1/6) [Technical Paper] Via Formation Process for Smooth Copper Wiring on Insulation Layer with Adhesion Layer Shinya Sasaki and Motoaki
More informationALTIUMLIVE 2018: NAVIGATING THE COMPLEXITIES OF PCB MATERIAL SELECTION
ALTIUMLIVE 2018: NAVIGATING THE COMPLEXITIES OF PCB MATERIAL SELECTION Chris Hunrath Insulectro, VP of Technology San Diego October 4 Outline 1 PCB Material Overview 2 What is the Dielectric Constant of
More informationRO4000 Series High Frequency Circuit Materials
Advanced Circuit Materials Division 100 S. Roosevelt Avenue Chandler, AZ 85226 Tel: 480-961-1382, Fax: 480-961-4533 www.rogerscorporation.com Advanced Circuit Materials Data Sheet RO4000 Series High Frequency
More informationRO4000 Series High Frequency Circuit Materials
Advanced Circuit Materials Division 100 S. Roosevelt Avenue Chandler, AZ 85226 Tel: 480-961-1382, Fax: 480-961-4533 www.rogerscorporation.com Advanced Circuit Materials Data Sheet RO4000 Series High Frequency
More informationRT/duroid 5870/5880 High Frequency Laminates Fabrication Guidelines
Fabrication Technical Articles Notes RT/duroid 5870/5880 High Frequency Laminates Fabrication Guidelines Notes on Packaging, Receiving, Storing, and Preparation for Processing Packaging High frequency
More informationHalogen-Free Dielectric Substrates
Halogen-Free Dielectric Substrates Halogen-Free Dielectric Substrates WEEE (Waste Electrical and Electronic Equipment (Draft proposal May 10, 2000) January 1, 2008 Halogen Elimination Deadline Halogen-Free
More informationOutline. Opportunities Overview of ASAP Areas of Application ASAP Proposal to Regulators Summary
Outline Opportunities Overview of ASAP Areas of Application ASAP Proposal to Regulators Summary Opportunities n Provide cost benefits and possible alternate methods for demonstrating product stability
More information