CONA -Universal / CONA -Connector

Transcription

1 CONA -Universal for quick assembly/disassembly on CONA -Connector or foreign system connectors CONA -Universal / CONA -Connector CONA B-Universal Bimetallic steam trap (BR 604) BR 604 Page CONA M-Universal Thermostatic steam trap (BR 6) BR 6 Page 3 CONA S-Universal Ball float steam trap (BR 68) BR 68 Page 4 CONA B-Universal Fig. 604 with CONA -Connector Fig CONA TD-Universal Thermodynamic steam trap - without strainer (BR 64) - with outside strainer (BR 643) BR 64 / 643 (Y) Page 5 CONA -Connector 68 System connector - with screwed sockets (BR 68...) - with socket weld ends (BR ) CONA -Connector 68 System connector with outside strainer - with flanges (BR 68...) - with screwed sockets (BR 68...) - with socket weld ends (BR ) - with butt weld ends (BR ) CONA -Connector 683 System connector with stop function at inlet - with flanges (BR ) - with screwed sockets (BR ) - with socket weld ends (BR ) - with butt weld ends (BR ) CONA -Connector 684 System connector with stop function at inlet and outlet - with flanges (BR ) - with screwed sockets (BR ) - with socket weld ends (BR ) - with butt weld ends (BR ) BR 68 Page 6 Forged steel BR 68 Page 6 Forged steel Stainless steel BR 683 Page 6 Forged steel Stainless steel BR 684 Page 6 Features CONA -Universal: For the discharge of - BR 604 / 6 / 64 / 643: sub-cooled condensate - BR 68: scalding hot condensate Automatic ventilation during start up and operation of the plant BR 604 / 64 / 643: Integrated non-return protection Installation position: - BR 604 / 6: any, except cap upside down - BR 68: always with drain plug upside down - BR 64: any - BR 643: always with strainer plug upside down Construction in high quality stainless steel Installation in any position Can be combined with all types of CONA -Connector Features CONA -Connector: Space saving, compact design Minimization of installation and maintenance labor Material optional in forged steel and stainless steel BR 68: with outside strainer BR 683 / 684: with integrated, low-maintenance stop valve with gland seal (on request with maintenance free bellows seal design acc. to german clean air act TA-Luft ) Simple replacement of steam traps by shut-off of inlet and outlet Optionally with blow-down valve BR 683: Recommended in combination with CODI -collector Elemination of potential leak points by reduced numbers of pipe joints Can be combined with all types of CONA -Universal Edition 0/06 - Data subject to alteration Datasheet 68000

2 CONA B-Universal - Bimetallic steam trap made of stainless steel Fig. 604 Universal flange with x 3/8 UNC-thread BR Bimetallic steam trap with corrosion resistant and water hammer proofed bimetallic controller Automatic ventilation during start up and operation of the plant Integrated non-return protection Inside strainer Installation in any position, except cap upside down Optimized design for quick installation Can be combined with all types of CONA -Connector (refer to page 6) Fig SA35CF8 Operating pressure PS (bar-g) allow. diff. pressure DPMX (bar): for controller: Universal flange R x 3/8 UNC-thread Dimensions and weights H 78 H acc. to connector type Weight approx. (kg) 0,8 Flow in kg/h Capacity chart The capacity chart shows the maximum flow at factory setting. Curve Maximum flow quantity of hot condensate at approx. 0 K below boiling temperature. Curve Maximum flow quantity of cold condensate at about 0 C (during start-up of a cold installation). The condensate-temperature determines the aperture of the control ler. The capacity is increasing with the sub-cooling temperature of the condensate. 00 0, 0,5 5 0 Differential pressure resp. inlet pressure in bar(g) Body SA35CF8 Strainer SA40Gr Cap SA8F3 Sealing ring (inside) spiral-wound gasket with graphite 7 Sealing ring (outside) spiral-wound gasket with graphite 4 Controller corrosion resist. bimetal TB 0 / 85 7 Hexagon screw SA93Gr.B6 Edition 0/06 - Data subject to alteration

3 CONA M-Universal - Thermostatic steam trap made of stainless steel BR 6 - Thermostatic steam trap with corrosion resistant and water hammer proofed capsule Inside strainer Installation in any position, except cap upside down (optimal filter effect at horizontal installation) Optimized design for quick installation With capsule for condensate sub-cooling about approx. 0K Can be combined with all types of CONA -Connector (refer to page 6) Fig. 6 Universal flange with x 3/8 UNC-thread Fig SA35CF8 Operating pressure PS (bar-g) 9 allow. diff. pressure DPMX (bar): for controller: Universal flange 9 R3 x 3/8 UNC-thread Dimensions and weights H 35 H acc. to connector type Weight approx. (kg) 0,5 Flow in kg/h Capacity chart The capacity chart shows the maximum flow. Curve Maximum flow quantity of hot condensate at approx. 0 K below boiling temperature. Curve Maximum flow quantity of cold condensate at about 0 C (during start-up of a cold installation). 0 0, 0, Differential pressure resp. inlet pressure in bar(g) Body SA35CF8 Strainer SA40Gr Capsule B Diaphragm Hastelloy Capsule SA40Gr Flat spring AISI 30 6 Cap SA8F3 Sealing ring (inside) spiral-wound gasket with graphite 7 Sealing ring (outside) spiral-wound gasket with graphite 7 Hexagon screw SA93Gr.B6 Edition 0/06 - Data subject to alteration 3

4 CONA S-Universal - Ball float steam trap made of stainless steel BR 68 - Ball float steam trap with level control for the condensate-discharge from all kinds of steam systems Rapid system start-up due to thermostatic control element (integrated capsule) Immediate discharge of hot boiling condensat Installation always with drain plug (Pos. 50) upside down Can be combined with all types of CONA -Connector (refer to page 6) Fig Body: SA8F3 Hood: SA40Gr.304 Operating pressure PS (bar-g) 9 allow. diff. pressure DPMX (bar): for controller: 9 R3 Universal flange x 3/8 UNC-thread Fig. 68 Universal flange with x 3/8 UNC-thread Dimensions and weights H 58 H 34 B 40 B acc. to connector type Weight approx. (kg),4 Flow in kg/h Capacity chart The capacity chart shows the maximum flow. Curve Maximum flow quantity of scalding hot condensate. Curve Maximum flow quantity of cold condensate at about 0 C. 0 0, 0, Differential pressure resp. inlet pressure in bar(g) Body SA8F3 Sealing ring (inside) spiral-wound gasket with graphite 6 Hood SA40Gr Sealing ring (outside) spiral-wound gasket with graphite 8 Retaining ring A4 4 Controller SA40Gr.304 Capsule: Hastelloymembran 7 Hexagon screw SA93Gr. B6 49 Sealing ring for plug * A4 50 Plug (M4x,5) * SA8F3 58 Loose flange SA8F3 * Spare parts 4 Edition 0/06 - Data subject to alteration

5 CONA TD-Universal - Thermodynamic steam trap made of stainless steel Fig. 64 without strainer Universal flange with x 3/8 UNC-thread BR 64 and BR Thermodynamic steam trap in compact design for the condensate-discharge of steam systems. Intermittent mode of operation Integrated non-return protection Design: - BR 64: without strainer - BR 643: with outside strainer Installation: - BR 64: any position - BR 643: strainer plug upside down Can be combined with all types of CONA -Connector (refer to page 6) Fig / (Y) - SA470Gr.40 / SA8F6 A Operating pressure PS (bar-g) 9 allow. diff. pressure DPMX (bar): permissible pressure ratio (bar-g): 9 Back pressure / Inlet pressure 0,8 Universal flange x 3/8 UNC-thread Flow in kg/h Fig. 643 with outside strainer Universal flange with x 3/8 UNC-thread Dimensions and weights Series 64 Series 643 H 4 84 H acc. to connector type H S S -- 0 HEX -- 3 Weight approx. (kg) 0,4,3 Capacity chart The capacity chart shows the maximum flow. Curve Maximum flow quantity of hot condensate. Curve Maximum flow quantity of cold condensate at about 0 C. 0 0, Differential pressure resp. inlet pressure in bar(g) Fig. 64 Fig. 643 Body SA470Gr.40 SA8F6 A 6 Cap SA470Gr.40 SA8F3 7 Strainer screen (Y) * -- SA40Gr Strainer plug (Y) * -- SA8F3 Sealing ring (inside) spiral-wound gasket with graphite spiral-wound gasket with graphite 7 Sealing ring (outside) spiral-wound gasket with graphite spiral-wound gasket with graphite 8 Retaining ring -- A4 5 Disc AISI440 AISI440 7 Hexagon screw SA93Gr.B6 SA93Gr.B6 58 Loose flange -- SA8 F3 Edition 0/06 - Data subject to alteration 5

6 CONA -Connector - System connector made of forged steel, stainless steel BR 68 / 68 / 683 / System connector for minimization of installation and maintenance space saving and compact design BR 683 / 684: with integrated, low-maintenance stop valve with gland seal (on request with maintenance free bellows seal design acc. to german clean air act TA-Luft ) Optional: - Blow down valve Fig SA35CF8 Operating pressure PS (bar-g) 9 Fig / / SA8F3 Operating pressure PS (bar-g) 3 Fig with screwed sockets Fig / / SA8F3 Operating pressure PS (bar-g) 3 Flanges... ANSI 300 RF Screwed sockets... Rp- and NPT-thread Socket weld ends...3 Butt weld ends...4 Other types of connection on request. Fig with outside strainer and screwed sockets Fig. 68/683/ with flanges Fig. 68/68/683/ with socket weld ends Fig. 68/683/ with butt weld ends 6 Fig with stop function at inlet and screwed sockets Fig with stop function at inlet and outlet and screwed sockets Edition 0/06 - Data subject to alteration

7 Dimensions and weights Nominal diameters Weight approx. (kg) mm inch L* L H H S Flanges Screwed sockets Socket weld ends Butt weld ends / 3/4 / 3/4 / 3/4 Fig Fig Fig Fig Fig Fig Fig. 68 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 Fig. 68 Fig. 683 Fig. 684 Fig Fig Fig Fig Fig Fig Fig Ø D Ø K 66,5 8, n x Ød 4 x 6 4 x 9 4 x * other face-to-face dimensions on request Fig ,6 0, Fig. 68,3,9 3,5,0,0,,3,4,5 Fig ,0 3,5 4,,7,6,8,9,0, Fig ,0 4,5 5,,7,6,8,9 3,0 3, Steam traps according to ASTM Pressure bearing parts made of -materials Studs and nuts made of ASTM-materials, with metric or american screw-threads Face-to-face dimension acc. to data sheet resp. customer request Flanges acc. to ANSI Pressure test acc. to API 598 BR 68 / 68 / 683 / Body (Fig. 68) -- SA35CF8 6 (Y) Body (Fig. 68) SA05 SA8F3 6.7 (Y) Strainer screen * SA40Gr.304 SA40Gr (Y) Strainer plug * SA8F3 SA8F3 6 Body (Fig. 683) SA05 SA8F3 6.3 Seat * AISI303 AISI Packing ring ( set) * Graphite Graphite 6.8 Assembly stop valve, cpl. * SA40 SA40 63 Body (Fig. 684) SA05 SA8F Seat * AISI303 AISI Packing ring ( set) * Graphite Graphite 63.8 Assembly stop valve, cpl. * SA40 SA40 * Spare parts Edition 0/06 - Data subject to alteration 7

8 Combinations CONA B- Universal 604 CONA M- Universal 6 CONA S- Universal 68 CONA TD- Universal 64 CONA TD- Universal 643 (Y) CONA -Connector Fig.... with screwed sockets Fig....3 with socket weld ends CONA -Connector Fig.... with flanges Fig.... with screwed sockets CONA -Connector Fig....3 with socket weld ends Fig....4 with butt weld ends CONA -Connector Technik mit Zukunft. DEUTSCHE QUALITÄTSARMATUREN ARI-Armaturen Albert Richter GmbH & Co. KG, D Schloß Holte-Stukenbrock, Tel / 994-0, Telefax / or 59 Internet: info.vertrieb@ari-armaturen.com 8 Edition 04/06 - Data subject to alteration