Superwall / Hydrowall System

Transcription

1 Certification Body: THIS TO CERTIFY THAT Certificate number: CM40085 ABN: JAS-ANZ Accreditation No. Z AK PO Box 7144, Sippy Downs Qld (07) Type and/or use of product: Structural Steel Framing. Superwall / Hydrowall System Description of product: The modular cold formed steel wall panel system used to form a structural wall system. Can be combined with modular slimline water tank that can store rainwater. COMPLIES WITH THE FOLLOWING BCA PROVISIONS AND STATE OR TERRITORY VARIATION(S) BCA 2016 Certificate Holder: Superwall Systems Pty Ltd ABN: Elizabeth Street, COTTESLOE, WA, 6011 Ph: Volume One Volume Two Performance Requirement(s) Not applicable to this product. Not applicable to this product. Deemed-to-Satisfy Provision(s): Not applicable to this product (a) & (b) (a) (i) (a) & (b). Steel framing Steel framing Steel framing State or territory variation(s): Not applicable to this product. Not applicable to this product. SUBJECT TO THE FOLLOWING LIMITATIONS AND CONDITIONS AND THE PRODUCT TECHNICAL DATA IN APPENDIX A AND EVALUATION STATEMENTS IN APPENDIX B Limitations and conditions: 1. This certification relates only to the structural steel framing compliance of the Hydrowall system. 2. All plumbing connections must be WaterMark certified. Where applicable, a qualified plumber must be used for this installation 3. Footing and slab supporting the Superwall / Hydrowall System must be designed in accordance with AS 2870: Where the Superwall / Hydrowall System contributes to the Tiedown & bracing of a building or structure the design must be assessed by a practising engineer. Building classification/s: Class 1 and 10 John Thorpe - CMI Don Grehan Unrestricted Building Certifier Date of issue: 6/10/2017 Date of expiry: 12/02/2020 Certificate number: CM40085 This certificate is only valid when reproduced in its entirety. Page 1 of 6

2 5. Certification is required for each structure at each address to ensure drawings comply with site requirements. Specification is invalid unless signed and certified for each structure at a single address. 6. This Certificate is issued based on the evidence of compliance as detailed herein. Any deviation from the specifications contained in this Certificate is outside of this document s scope and the installation of the certified product/system will not be covered by this CodeMark certification. This may result in the product being classified as a non-conforming building product/system. Scope of certification: The CodeMark Scheme is a building product certification scheme. The rules of the Scheme are available at the ABCB website This Certificate of Conformity is to confirm that the relevant requirements of the Building Code of Australia (BCA) as claimed against have been met. The responsibility for the product performance and its fitness for the intended use remain with the certificate holder. The certification is not transferrable to a manufacturer not listed on Appendix A of this certificate. Disclaimer: The Scheme Owner, Scheme Administrator and Scheme Accreditation Body do not make any representations, warranties or guarantees, and accept no legal liability whatsoever arising from or connected to, the accuracy, reliability, currency or completeness of any material contained within this certificate; and the Scheme Owner, Scheme Administrator and Scheme Accreditation Body disclaim to the extent permitted by law, all liability (including negligence) for claims of losses, expenses, damages and costs arising as a result of the use of the product(s) referred to in this certificate. Certificate number: CM40085 This certificate is only valid when reproduced in its entirety. Page 2 of 6

3 APPENDIX A PRODUCT TECHNICAL DATA A1 Type and intended use of product As per page one. A2 Description of product Superwall components include: - Standard Powdercoated Steel Posts 1800mm 4200mm; - Powdercoated Steel Beams 1200mm and 600mm; - Powdercoated Steel Side Beams 280mm - Bolts, Washers, Nuts 8 sets per cross beam; - Anchor bolts 2 of. Hydrowall components include: - Standard Powdercoated Steel Posts 1800mm 4200mm; - Powdercoated Steel Beams 1200mm and 600mm; - Powdercoated Steel Side Beams 280mm - Bolts, Washers, nuts 8 sets per cross beam; - Anchor bolts 2 of; - Liner Qty 1 (Available in Potable (TPU) and non-potable grade (PVC)); - Liner fittings 1 kit for each wall section. A3 Product specification Wall configuration: Height Beam Length Spacer Length 3000 mm 1200 mm 280 mm Wall sections are: Upright U80 x 60 x 2.0 Beam F40 x 60 x 2.0 Spacer F25 x 50 x 1.5 Certificate number: CM40085 This certificate is only valid when reproduced in its entirety. Page 3 of 6

4 Material Properties The material for all the components is Q235. Material properties are list as follows: Yield Strength 235 MPa Young s Modulus MPa Poisson s ratio 0.3 Density 7850 Kg/m3 Load Combinations for Design Ultimate Limit State: 1.0DL + 1.4PL + 1.4IcL 1.0DL + 1.4PL + 1.4IdL Serviceable Limits State: 1.0DL + 1.0PL + 1.0IcL 1.0DL + 1.0PL + 1.0IdL Seismic Finite Element Analysis Description Analysis Result Allowable Value Evaluation Stress of Upright 68 MPa 235 MPa Meet Stress ratio of Upright Meet Stress of Beam 41 MPa 235 MPa Meet Stress ratio of Beam Meet Stress of Spacer 25 MPa 235 MPa Meet Stress ratio of Spacer Meet Cross-aisle Sway 0.87 mm 15 mm (Height/200) Meet Down-aisle Sway 0.11 mm 15 mm (Height/200) Meet Vertical Deflection 0.05 mm 6 mm (Span/200) Meet A4 Manufacturer and manufacturing plant(s) This field is voluntary. For more information, contact the Certificate Holder. A5 Installation requirements 1. Must be installed in accordance with Hydrowall Installation Manual (DOC# 1201 M 100 C Version C December 2013). 2. Only to be installed in accordance with the requirements of AS/NZS 4600:2005 Cold Form Steel Structures. Certificate number: CM40085 This certificate is only valid when reproduced in its entirety. Page 4 of 6

5 3. Construction is to be signed off by a suitably licensed Engineer. A6 Other relevant technical data 1. If construction site is in a Cyclonic region, the building must be engineered to conform to regional Cyclonic zone requirements. 2. No substitution of any component without the express written permission of the Certificate Holder. 3. All component parts not supplied by Hydrowall including cladding system, battens and fixings for cladding system, insulation, roofing structure or connecting brackets, must meet the required Australia Standard. Certificate number: CM40085 This certificate is only valid when reproduced in its entirety. Page 5 of 6

6 APPENDIX B EVALUATION STATEMENTS B1 Evaluation methods 1. Structural Provision (a) (iii). Reports from Professional Engineer. B2 Reports 1. Exceed Consulting (WA) Pty Ltd May 2012 Finite Element Analysis Report. In accordance to AS/NZS 4600:2005 Cold Form Steel Structures and AS Structerre Consulting Engineers HYDROWALL Structural drawings. Certificate number: CM40085 This certificate is only valid when reproduced in its entirety. Page 6 of 6