FLAME CURB. Type X, Type XXX, Type C Gypsum Wallboard. Submittal Description: Primary Uses: Limitations: Application:

Transcription

1 Submittal TYPE XXX a division of PABCO building products, LLC "Quality to the Core" PABCO Gypsum a division of PABCO building products, LLC PO Box Rancho Cordova, CA Technical Services: Description: Primary Uses: R FLAME CURB Type X, Type XXX, Type C Gypsum Wallboard PABCO Gypsum Specification PGS-002 AS specification C 1396 Available in MOLD CURB Plus type X to the PABCO FLAME CURB gypsum wallboard is a family of gypsum panel products composed of a fire-resistant gypsum core, reinforced with glass fibers which provides increased strength and enhanced fire-resistant properties. The face paper is folded around the long edges to reinforce as well as to protect the core; the panel ends are cut square. The long panel edges are tapered, allowing a recessed joint area to be reinforced and concealed to create a monolithic wall or ceiling surface suitable for decoration. PABCO 5/8" FLAME CURB type X and 1/2" FLAME CURB type XXX meet and/or exceed the requirements specified by AS under its wallboard standard AS C 1396 type-x. FLAME CURB Super C, in thicknesses of 1/2" and 5/8", exceed all of these previously mentioned classified core formulations in fire-resistance performance. (Systems are specifically tested at approved laboratories (see listing under Application) using these various core formulas, and those systems which successfully pass the stringent fire tests are approved for construction and are listed in the fire testing lab directory or in the Gypsum Association Fire Resistance Design Manual GA-600). PABCO FLAME CURB is manufactured with 100% recycled paper on face and back sides, affording a surface designed to receive joint treatment, paint, wall covering, or textured coatings. PABCO FLAME CURB is a non-structural wall covering material intended for interior walls, ceilings, and partitions in residential and commercial applications which often require specific fire-resistant assemblies. Additional applications include use as a roof underlayment per GA-276. This product is designed for direct mechanical attachment to metal or wood framing members. With the wallboard joints properly treated per GA-216 and GA-214, PABCO FLAME CURB will resist the passage of smoke. TYPE XXX Limitations: PABCO FLAME CURB is intended for interior applications, and shall not be used where there will be direct exposure to water or continuous high humidity before, during, and after construction. Avoid exposure to temperatures exceeding 125 of (52 oc) for an extended period of time. PABCO FLAME CURB is a non-structural panel, not to be used as a structural fastener base or to support wall or ceiling mounted objects. All materials used in conjunction with the application of PABCO FLAME CURB type X, XXX, or Super C gypsum panels in Fire or Sound Rated systems shall be as specified in the applicable specific test report. TYPE XXX Application: PABCO Gypsum endorses the Gypsum Association s publication GA-216 and AS Standard Specification C 840 as its application documents, which provide detailed instructions on the standard application of wallboard panels and proper joint finishing procedures. PABCO FLAME CURB systems must be installed in strict compliance with the detailed fire test assembly description, including core types and other components such as studs, fastener spacing and fasteners required, and applied as tested. To qualify for listed sound ratings, special caulking, insulation, or clips are generally added to the systems as detailed in the test report. Those systems that have been fire and sound tested are listed in the following: Gypsum Association Fire Resistance Design Manual (GA-600). PABCO Gypsum Quality to the Core Brochure (see PABCO Gypsum website). ICC: ESR UL Fire Resistance Directory. ITS, NGTS, NRC, RAL, SWRi, UL, or WFCi Test Reports. Finishing of joints, wall or ceiling surfaces, and covering fasteners, is addressed in GA-214, GA-216, and AS C 840.

2 Product Data: Sizes and Types Product UL Core Type Edge Type 1 Thickness 2 Width 2 Length 3 Weight 4 Type XXX PG-3 TE 1/2" 48" 8', 12' 1.9 lbs/ft 2 Super C PG-C TE 1/2" 48" 12' 2.0 lbs/ft 2 Type X PG-11 TE & RE 1 5/8" 48"&54" 8'-12' 2.2 lbs/ft 2 TYPE XXX Super C TYPE C TE 5/8" 48" 12' 2.4 lbs/ft 2 Packaging: 2 pieces per bundle, face-to-face, and end labeled. 1 Edge types: Tapered Edge (TE). Round Edge (RE) is available (only) on FLAME CURB 5/8" x 48" widths. 2 Units of measure: inches. 3 Units of measure: feet. Other lengths may be available on a special order basis. Refer to PABCO s Products- Packaging-Weights page. Consult with your local PABCO representative, or call PABCO Technical Assistance. 4 Represents approximate weight for design and shipping purposes. A more exact weight may be available for your area; consult with your local PABCO representative, or call PABCO Technical Assistance. Good to the left only Applicable Standards & Reference Documents: Manufacturing: AS C 1396; Federal Specification SS-L-30D Type III, Grade X * Installation: Gypsum Association GA-216, GA-214; AS C 840, Fire-Resistant Assemblies: Gypsum Association GA-600, Fire Design Manual Underwriters Laboratories, UL Fire Resistance Directory Surface Burning AS E 84; UL: Fire Resistance Directory Characteristics: Flame Spread 15, Smoke Developed 0 Non-Combustible: AS E 136, R value: 1/2" = 0.45; 5/8" = 0.48 Thermal Resistance VOC/Asbestos content: Free of VOC (Volatile Organic Compound) & asbestos Material Safety Data Sheet: MSDS available at Technical Data PABCO Gypsum: Construction Guide - Fire & Sound Rated Systems Foil Application: Foil may be applied to the back of AS C 1396 gypsum wallboard for the purpose of complying with AS C 1396 paragraph 5.1. Recycled Content: Refer to PABCO Sustainable Materials Data Sheet for plant specific details. Please check our website at for the latest edition of this specification. * The federal specification for gypsum board, SS-L-30d was withdrawn in It is provided here for informational purposes only. Storage & Handling: Store all PABCO gypsum panels flat; do not store on edge as panels are heavy and may fall over causing injury or death. Store in an area that offers protection from adverse weather conditions, condensation, and other forms of moisture. Avoid job site conditions that expose gypsum board to water or moisture. Plastic shipping bags are temporary, intended for protection during transit only, and must be removed promptly upon arrival. Store gypsum board under protected cover, off the ground with sufficient support to prevent sagging. Exercise proper care to avoid impact, scuffing of the paper faces, undue flexing, and damage to board edges, corners, and ends. TYPE XXX Fire Resistant Ratings: Fire Resistance Rated assembly designs are promulgated from tests performed at IAS* certified independent testing laboratories, and these designs include specific materials assembled in a precise configuration. When choosing construction details to achieve specific fire resistance rated requirements, care must be taken to insure that each component of the specified assembly is the proper one specified in the test report, and assembled in accordance with the specific requirements of the assembly. *(The International Accreditation Service IAS is a non-profit, public benefit corporation and a leading accreditation body in the United States. Internationally recognized, accreditation by IAS makes it easier to market products and services both inside and outside the United States.) Submittal Approvals: Job name: Contractor: Date: TYPE XXX Limited Warranty: PABCO Building Products, LLC, warrants that on the date the gypsum board is shipped from its manufacturing plant the gypsum board is free from defects in materials and manufacture. NOTWITHSTANDING THE FOREGOING, IT IS THE RESPONSIBILITY OF THE APPLICATOR TO NOTIFY PABCO BUILDING PRODUCTS, LLC, IN WRITING WITHIN TWENTY FOUR (24) HOURS OF DISCOVERY OF ANY VISIBLY DEFECTIVE PRIOR TO SUCH VISIBLY DEFECTIVE BEING APPLIED; FAILURE TO DO SO MAY FURTHER LIMIT OR VOID THE RESPONSIBILITIES OF PABCO BUILDING PRODUCTS, LLC, UNDER THIS WARRANTY. This warranty will remain in place for one year from the date of shipment from the manufacturing plant. THIS EXPRESS WARRANTY IS THE EXCLUSIVE WARRANTY PROVIDED BY PABCO BUILDING PRODUCTS, LLC, AND SUPERSEDES ANY PRIOR, CONTRARY OR ADDITIONAL REPRESENTATIONS, WHETHER ORAL OR WRITTEN. PABCO BUILDING PRODUCTS, LLC, HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED, OR STATUTORY INCLUDING ANY WARRANTY OF MERCHANTABILITY, ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY IMPLIED WARRANTIES OTHERWISE ARISING FROM COURSE OF DEALING OR USAGE OF TRADE. If the gypsum board fails to conform to the foregoing warranty in Paragraph 1 and such nonconformity is not due to misuse or improper maintenance or storage, Buyer shall notify PABCO Building Products, LLC, in writing, and within 60 days of discovery, PABCO Building Products, LLC, shall provide, at its sole and absolute discretion, one of the following: (i) repair or replacement of any nonconforming or defective gypsum wallboard; or (ii) credit or full refund of the purchase price. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY OF BUYER FOR ANY BREACH OF WARRANTY. IN NO EVENT SHALL PABCO BUILDING PRODUCTS, LLC, BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE, OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT OR FROM NEGLIGENCE OR OTHER TORT. This exclusion applies regardless of whether such damages are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other legal theory. Trademarks: The following trademarks used herein are owned by Pacific Coast Building Products and licensed to PABCO Gypsum: PABCO, PABCORE, FLAME CURB, WATER CURB, MOLD CURB, Quality to the Core, and ABUSE CURB. Note: Products described herein may not be available in all geographic markets. Consult your PABCO Gypsum sales representative for information. Page 17 SJ/ /Flame Curb PABCO Gypsum

3 PANEL DE YESO FABRICADO DE ACUERDO A LA NORMA AS C PA PABCO, DIV. OF PABCO BUILDING PRODUCTS, LLC, NEWARK, CA, USA MANUFACTURED TO MEET AS C PABCO, UNA DIVISIÓN DE PABCO BUILDING PRODUCTS, LLC NEWARK, CALIFORNIA, USA PANEL DE YESO FABRICADO DE ACUERDO A LA NORMA AS C PANEL DE YESO PARA SOFITO TIPO C PABCO, DIV. OF PABCO BUILDING PRODUCTS, LLC, NEWARK, CA, USA PANEL DE YESO SOFITO 5/8 x 12 PANEL DE YESO 1/2 x 12 1/2 x 12 5/8 x 1/2 x 12 PANEL DE YESO FABRICADO DE ACUERDO A LA NORMA AS C PANEL DE YESO PARA SOFITO TIPO C PANEL PARA DE YESO 1/2 x SOFITO 12 TIPO C TIPO C TYPE C MANUFACTURED TO MEET AS C TYPE C TYPE C PABCO, UNA DIVISIÓN DE PABCO BUILDING PRODUCTS, LLC NEWARK, CALIFORNIA, USA MANUFACTURED TO MEET AS C TYPE C PABCO, DIV. OF PABCO BUILDING PRODUCTS, LLC, NEWARK, CA, USA PABCO, UNA DIVISIÓN DE PABCO BUILDING PRODUCTS, LLC N Submittal MANUFACTURED TO MEET AS C PABCO, DIV. OF PABCO BUILDING PRODUCTS, LLC, NEWARK, CA, USA a division of PABCO building products, LLC "Quality to the Core" PABCO Gypsum a division of PABCO building products, LLC PO Box Rancho Cordova, CA Technical Services: Description & Primary Uses: Limitations: Application: R Regular, Type X, Type C Sag Resistant PABCO Specification PGS-005 AS specification C 1396 Available in MOLD CURB Plus to the PABCO Exterior Gypsum Soffit Board is designed for exterior ceiling application on the underside of exterior soffits, open porches, walkways, carport ceilings and similar installations that are completely protected from contact with water. The core and paper has been formulated to enhance its ability to resist sagging when applied in the prescribed manner. PABCO Exterior Soffit Board panels are manufactured in 1/2" Regular, 1/2" type XXX, 5/8"type X, and 5/8" type C cores. The face paper is cream or light-brown colored with the core type printed in the taper area along the long-edges. The long panel edges are tapered to receive joint treatment. PABCO Exterior Gypsum Soffit Board shall not be subjected to direct exposure to weather, and water. 24" o.c. (on center) joist spacing is the maximum span for PABCO type X Exterior Gypsum Soffit Board. An approved exterior surface decoration (alkyd paint) must be applied to all exposed soffit board. (See TSR: 1338). All materials and application of PABCO type X Exterior Gypsum Soffit Board on fire rated assemblies shall be as indicated in the fire test report. PABCO Exterior Gypsum Soffit Board Shall not be exposed to sustained temperatures exceeding 125o F (52o C). PABCO Exterior Gypsum Soffit Board is non-structural, and not to be used as a structural fastener base, or to support heavy wall or ceiling mounted objects. PABCO Gypsum recommends that its Exterior Gypsum Soffit Board application conform to recommendations in GA-216 and AS C 840. Panels shall be applied perpendicular to ceiling joists, in a horizontal plane or inclined downward away from the structure in ceiling applications. Panels may be used as a covering on interior wall surfaces. All joints and fasteners not covered by exterior cladding or outer layers in a multi-layer system shall be finished with tape and joint compound. Unless protected by metal or other water stops, all edges of the soffit board shall be spaced a minimum of 1/4"(inch) away from adjacent vertical surfaces. Suitable fascia and molding shall be provided around the perimeter of the soffit or ceiling to protect the gypsum panels from direct exposure to water. All soffit board indirectly exposed shall be decorated with an approved exterior cladding or painting system. When PABCO type X Exterior Gypsum Soffit Board is specified for use in fire rated systems, the UL core type specified and the application method must be as specified in the fire tested system selected.

4 ILDING PRODUCTS, LLC, NEWARK, CA, USA 1/2 x 12 MEET AS C Product Data, Sizes and Types: Product UL Core Type Thickness Width Length 2 Weight 1 Exterior Regular - 1/2" 48" 12' 1.7 lbs/ft 2 Exterior Soffit type X PG-3 1/2" 48" 12' 2.0 lbs/ft MANUFACTURED TO MEET AS C PANEL DE YESO FABRICADO DE ACUERDO A LA NORMA AS C PANEL DE YESO PARA SOFITO TIPO C PANEL DE YESO PARA SOFITO TIPO C PABCO, UNA DIVISIÓN DE PABCO BUILDING PRODUCTS, LLC NEWARK, CALIFORNIA, USA PANEL DE YESO FABRICADO DE ACUERDO A LA NORMA AS C PANEL DE YESO PARA SOFITO TIPO C 1/2 x 12 1/2 x 12 5/8 x 12 PANEL DE YESO PARA SOFITO TIPO C 5/8 x 12 PABCO, UNA DIVISIÓN DE PABCO BUILDING PRODUCTS, LLC NEWARK, CALIFORNIA, USA PABCO, DIV. OF PABCO BUILDING PRODUCTS, LLC, NEWARK, CA, USA MANUFACTURED TO MEET AS C TYPE C TYPE C PABCO, DIV. OF PABCO BUILDING PRODUCTS, LLC, NEWARK, CA, USA Applicable Standards & Reference Documents: Storage & Handling: Fire Resistant Ratings: Submittal Approvals: Exterior Soffit type X PG-11 5/8" 48" 8', 12' 2.3 lbs/ft 2 Exterior Soffit type C type C 5/8" 48" 8', 12' 2.4 lbs/ft 2 Packaging: 2 pieces per bundle, face-to-face, and end taped Edge type: Tapered 1 Represents approximate weight for design and shipping purposes. A more exact weight may be available for your area; consult with your local PABCO representative, or call PABCO Technical Assistance. 2 Other lengths may be available on a special order basis. Consult with your local PABCO representative, or call PABCO Technical Assistance. Manufacturing: AS C 1396; Federal Specification SS-L-30D Type III, Grade X * Installation: Gypsum Association GA-216, AS C 840, Fire-Resistant Assemblies: Gypsum Association GA-600, Fire Design Manual Underwriters Laboratories, UL Fire Resistance Directory Surface Burning AS E 84; Characteristics: Flame Spread 15, Smoke Developed 0 Non-Combustible: AS E 136, R value: 1/2" = 0.45; 5/8" = 0.48 Thermal Resistance VOC/Asbestos: Free of VOC (Volatile Organic Compound) & asbestos Material Safety Data Sheet: MSDS available at Technical Data PABCO Gypsum: Construction Guide - Fire & Sound Rated Systems Recycled Content: Refer to PABCO Sustainable Materials Data Sheet for plant specific details. Please check our website at for the latest edition of this specification. * The federal specification for gypsum board, SS-L-30d was withdrawn in It is provided here for informational purposes only. Store all PABCO gypsum panels flat; do not store on edge as panels are heavy and may fall over causing injury or death. Store in an area that offers protection from adverse weather conditions, condensation, and other forms of moisture. Avoid job site conditions that expose gypsum board to water or moisture. Plastic shipping bags are temporary, and intended for protection during transit only, and must be removed promptly upon arrival. Store gypsum board under protected cover, off the ground with sufficient support to prevent sagging. Exercise proper care to avoid impact, scuffing of the paper faces, undue flexing, and damage to board edges, corners, and ends. Fire Resistance Rated assembly designs are promulgated from tests performed at IAS* certified independent testing laboratories, and these designs include specific materials assembled in a precise configuration. When choosing construction details to achieve specific fire resistance rated requirements, care must be taken to insure that each component of the specified assembly is the proper one specified in the test report, and assembled in accordance with the specific requirements of the assembly. *(The International Accreditation Service IAS is a non-profit, public benefit corporation and a leading accreditation body in the United States. Internationally recognized, accreditation by IAS makes it easier to market products and services both inside and outside the United States.) Job name: Contractor: Date: MANUFACTURED TO MEET AS C TYPE C TYPE C PABCO, DIV. OF PABCO BUILDING PRODUCTS, LLC, NEWARK, CA, USA Limited Warranty: PABCO Building Products, LLC, warrants that on the date the gypsum board is shipped from its manufacturing plant the gypsum board is free from defects in materials and manufacture. NOTWITHSTANDING THE FOREGOING, IT IS THE RESPONSIBILITY OF THE APPLICATOR TO NOTIFY PABCO BUILDING PRODUCTS, LLC, IN WRITING WITHIN TWENTY FOUR (24) HOURS OF DISCOVERY OF ANY VISIBLY DEFECTIVE PRIOR TO SUCH VISIBLY DEFECTIVE BEING APPLIED; FAILURE TO DO SO MAY FURTHER LIMIT OR VOID THE RESPONSIBILITIES OF PABCO BUILDING PRODUCTS, LLC, UNDER THIS WARRANTY. This warranty will remain in place for one year from the date of shipment from the manufacturing plant. THIS EXPRESS WARRANTY IS THE EXCLUSIVE WARRANTY PROVIDED BY PABCO BUILDING PRODUCTS, LLC, AND SUPERSEDES ANY PRIOR, CONTRARY OR ADDITIONAL REPRESENTATIONS, WHETHER ORAL OR WRITTEN. PABCO BUILDING PRODUCTS, LLC, HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED, OR STATUTORY INCLUDING ANY WARRANTY OF MERCHANTABILITY, ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY IMPLIED WARRANTIES OTHERWISE ARISING FROM COURSE OF DEALING OR USAGE OF TRADE. If the gypsum board fails to conform to the foregoing warranty in Paragraph 1 and such nonconformity is not due to misuse or improper maintenance or storage, Buyer shall notify PABCO Building Products, LLC, in writing, and within 60 days of discovery, PABCO Building Products, LLC, shall provide, at its sole and absolute discretion, one of the following: (i) repair or replacement of any nonconforming or defective gypsum wallboard; or (ii) credit or full refund of the purchase price. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY OF BUYER FOR ANY BREACH OF WARRANTY. IN NO EVENT SHALL PABCO BUILDING PRODUCTS, LLC, BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE, OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT OR FROM NEGLIGENCE OR OTHER TORT. This exclusion applies regardless of whether such damages are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other legal theory. Trademarks: The following trademarks used herein are owned by Pacific Coast Building Products and licensed to PABCO Gypsum: PABCO, PABCORE, FLAME CURB, WATER CURB, MOLD CURB, Quality to the Core, and ABUSE CURB. Note: Products described herein may not be available in all geographic markets. Consult your PABCO Gypsum sales representative for information. Page #21 SJ /Soffit PABCO Gypsum

5 Submittal a division of PABCO building products, LLC "Quality to the Core" R PABCORE SHAFTLINER PABCO Gypsum a division of PABCO building products, LLC PO Box Rancho Cordova, CA Technical Services: PABCO Gypsum Specification PGS-008 AS specification C 1396 to the Description: PABCORE SHAFTLINER type X panels are manufactured with a proprietary fire resistant type X core which has been reinforced with glass fibers and speciality additives to increase its fire-resistance. This core is encased in 100% recycled water-resistant face and back paper, and features a double beveled edge for ease of installation. PABCORE SHAFTLINER type X is distinguishable by the light green coloration of the water-resistant paper facing. Primary Uses: PABCORE SHAFTLINER type X panels are designed for lining elevator, ventilation, and utility shafts, as well as constructing lightweight sound attenuation fire-resistant cavity shaft walls, and area separation fire walls in multifamily dwellings such as townhouses, condominiums, and apartments. These panels are key components in PABCO Shaftwall and Area Separation Fire Wall (ASFW) Systems utilizing C-H, C-T Studs or H-Studs. PABCO Shaftwall Systems are easy to erect, achieving fire-resistance ratings of one and two hours. Both solid and cavitytype area separation walls provide Sound Transmission Class (STC) ratings that exceed model building code requirements with designs that achieve STC ratings in excess of 60. Area Separation Fire Wall assemblies are light weight, weighing no more than 10 lbs/ft 2 when constructed. As a result, the need for costly footings or foundation modifications are often eliminated. Due to the relatively light weight panels, they can be installed up to four (4) stories in height. When used as an area separation wall, the system must be: ʶʶ Continuous from the foundation to the underside of the protected roof sheathing or continue through the roof to form a parapet. ʶʶ Designed to allow for collapse of the construction on the side of the wall exposed to fire without collapse of the area separation fire wall. Limitations: Shaftwall/Stairwell systems are designed as nonload bearing. (NLB) Do not install in areas which will be adjacent to occupancies of unusually high moisture conditions. Where penetrations occur in the assembly, additional reinforcement at corners may be required to distribute stress; approved flexible sealant/caulking may be required to seal around some penetrations. Through penetrations are not allowed in area separation fire walls that are designed to collapse on the fire side. Not recommended for use as an unlined HVAC supply shaft or duct. Limiting heights and deflection criteria must be based upon the metal stud manufacturer s recommendations. Page #24

6 Application: PABCORE SHAFTLINER type X and PABCORE MOLD CURB Plus SHAFTLINER type X panels may be used in one and two-hour shaftwall systems, one and two-hour horizontal corridor ceiling systems and two-hour Area Separation Walls. Refer to the PABCO Gypsum Shaftwall Systems publication for details. Product Data, Sizes and Types: UL Core Type Thickness Width Length 1 Edge Type Weight 2 PG-10 1 inch 24 inches 8', 10',12' Double beveled 4.4 lbs/ft 2 PABCORE SHAFTLINER products are certified by a third-party inspection service. Each panel bears the UNDERWRITERS LABORATORIES, Inc. label to indicate CERTIFICATION of fire resistance, surface burning characteristics, and non-combustibility. 1 Other lengths may be available on a special order basis. Consult with your local PABCO representative, or call PABCO Technical Assistance. 2 Represents approximate weight for design and shipping purposes. A more exact weight may be available for your area; consult with your local PABCO representative, or call PABCO Technical Assistance. Applicable Standards, Codes & Technical Data: Manufacturing: AS C 1396; Federal Specification Type IV, Grade X* Installation: Gypsum Association GA-216, AS C 840, Fire-Resistant Assemblies: Gypsum Association GA-600, Fire Design Manual Underwriters Laboratories, UL Fire Resistance Directory Surface Burning AS E 84; UL: Fire Resistance Directory Characteristics: Flame Spread 15, Smoke Developed 0 Non-Combustible: AS E 136, R value: 0.83 Thermal Resistance VOC/Asbestos: Free of VOC (Volatile Organic Compound) & asbestos Material Safety Data Sheet: MSDS available at Technical Data PABCO Gypsum: Construction Guide - Fire & Sound Rated Systems Recycled Content: Refer to PABCO Sustainable Materials Data Sheet for plant specific details. Please check our website at for the latest edition of this specification. * The federal specification for gypsum board, SS-L-30d was withdrawn in It is provided here for informational purposes only. Storage & Handling: Store all PABCO gypsum panels flat; do not store on edge as panels are heavy and may fall over causing injury or death. Store in an area that offers protection from adverse weather conditions, condensation, and other forms of moisture. Avoid job site conditions that expose gypsum board to water or moisture. Plastic shipping bags are temporary, and intended for protection during transit only, and must be removed promptly upon arrival. Store gypsum board under protected cover, off the ground with sufficient support to prevent sagging. Exercise proper care to avoid impact, scuffing of the paper faces, undue flexing, and damage to board edges, corners, and ends. Fire Resistant Ratings: Fire Resistance Rated assembly designs are promulgated from tests performed at IAS* certified independent testing laboratories, and these designs include specific materials assembled in a precise configuration. When choosing construction details to achieve specific fire resistance rated requirements, care must be taken to insure that each component of the specified assembly is the proper one specified in the test report, and assembled in accordance with the specific requirements of the assembly. *(The International Accreditation Service IAS is a non-profit, public benefit corporation and a leading accreditation body in the United States. Internationally recognized, accreditation by IAS makes it easier to market products and services both inside and outside the United States.) Submittal Approvals: Job name: Contractor Date: Limited Warranty: PABCO Building Products, LLC, warrants that on the date the gypsum board is shipped from its manufacturing plant the gypsum board is free from defects in materials and manufacture. NOTWITHSTANDING THE FOREGOING, IT IS THE RESPONSIBILITY OF THE APPLICATOR TO NOTIFY PABCO BUILDING PRODUCTS, LLC, IN WRITING WITHIN TWENTY FOUR (24) HOURS OF DISCOVERY OF ANY VISIBLY DEFECTIVE PRIOR TO SUCH VISIBLY DEFECTIVE BEING APPLIED; FAILURE TO DO SO MAY FURTHER LIMIT OR VOID THE RESPONSIBILITIES OF PABCO BUILDING PRODUCTS, LLC, UNDER THIS WARRANTY. This warranty will remain in place for one year from the date of shipment from the manufacturing plant. THIS EXPRESS WARRANTY IS THE EXCLUSIVE WARRANTY PROVIDED BY PABCO BUILDING PRODUCTS, LLC, AND SUPERSEDES ANY PRIOR, CONTRARY OR ADDITIONAL REPRESENTATIONS, WHETHER ORAL OR WRITTEN. PABCO BUILDING PRODUCTS, LLC, HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED, OR STATUTORY INCLUDING ANY WARRANTY OF MERCHANTABILITY, ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY IMPLIED WARRANTIES OTHERWISE ARISING FROM COURSE OF DEALING OR USAGE OF TRADE. If the gypsum board fails to conform to the foregoing warranty in Paragraph 1 and such nonconformity is not due to misuse or improper maintenance or storage, Buyer shall notify PABCO Building Products, LLC, in writing, and within 60 days of discovery, PABCO Building Products, LLC, shall provide, at its sole and absolute discretion, one of the following: (i) repair or replacement of any nonconforming or defective gypsum wallboard; or (ii) credit or full refund of the purchase price. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY OF BUYER FOR ANY BREACH OF WARRANTY. IN NO EVENT SHALL PABCO BUILDING PRODUCTS, LLC, BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE, OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT OR FROM NEGLIGENCE OR OTHER TORT. This exclusion applies regardless of whether such damages are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other legal theory. Trademarks: The following trademarks used herein are owned by Pacific Coast Building Products and licensed to PABCO Gypsum: PABCO, PABCORE, FLAME CURB, WATER CURB, MOLD CURB, Quality to the Core, and ABUSE CURB. Note: Products described herein may not be available in all geographic markets. Consult your PABCO Gypsum sales representative for information. Page #25 SJ /Shaftliner PABCO Gypsum

7 Submittal a division of PABCO building products, LLC "Quality to the Core" R REGULAR Gypsum Wallboard PABCO Gypsum a division of PABCO building products, LLC PO Box Rancho Cordova, CA Technical Services: PABCO Gypsum Specification PGS-001 AS specification C 1396 Available in MOLD CURB Plus PABCO s famous to the Products Description: PABCO Regular Gypsum Wallboard is an interior gypsum board product with a fireresistant, dimensionally stable, gypsum core. Each panel is encased in a 100% recycled paper on the face and back sides. The face paper is folded around the long edges to reinforce and protect the core; the ends are square cut and finished smooth. Long edges of panels are tapered providing a recessed area that allows joints to be reinforced and concealed with joint treatment creating a monolithic wall finish. High quality face paper manufactured by PABCO Paper provides a smooth surface which can be decorated with paint, texture or wallpaper. Primary Uses: PABCO Regular Gypsum Wallboard products are utilized in non-structural wall, ceiling and partition applications, for use in new construction or renovation work. Both may also be used as a covering material for flat or curved surfaces. Limitations: PABCO Regular Gypsum Wallboard panels are intended for interior applications and shall not be used where there will be direct exposure to water or continuous high humidity before, during, and/or after construction. Gypsum panel products shall not be exposed to sustained temperatures exceeding 125 F (52 C). PABCO Regular Gypsum Wallboard panels are non-structural, not to be used as a structural fastener base, or to support heavy wall or ceiling mounted objects. Installation to walls shall be with the bottom edge spaced a minimum of 1/4" inch (6 mm) above the floor. Advantages: Cost efficient, lightweight, and non-combustible core. Accepts a wide range of decorative finishes. Consistent edge tapers produce a monolithic flat surface. Easily cut, permitting quick installation, painting and/or decorating. Negligible expansion and contraction under normal atmospheric changes. Application: PABCO Gypsum endorses the Gypsum Association s publications GA-216 and GA-214 as well as AS Standard Specification C 840 as its application and finishing specifications. These similar specifications give detailed instruction on the standard application of wallboard panels and proper joint finishing procedures. PABCO Gypsum Wallboard panels may be attached to wood or steel framing with nails, screws and/or adhesives. Finishing of joints and covering fasteners is detailed in GA 214 and/or AS C 840. A combination of nails on the perimeters and screws in the field of panels is permitted with the spacing the same as described for each type fastener. PABCO Gypsum Wallboard panels shall be cut to fit as closely as possible without forcing panels in place. PABCO Gypsum Wallboard joints shall not be aligned with door or window openings; joints shall be offset at least 6. Temperature at time of panel application shall be above 40 degrees F and shall be maintained at 50 degrees F 48 hours prior to and during application and drying of joint compound. Special treatment of assemblies for additions such as control joints, resilient channel, insulation and perimeter relief systems shall be as specified in the tested system. Page #30

8 Product Data: Sizes and Types Applicable Standards and Technical Data: Core Thickness Width Length 1 Weight 2 Regular 1/4" 48" 8' 1.1 lbs/ft 2 Regular & FLEX 3/8" 48" 8' 1.3 lbs/ft 2 Regular 1/2" 48" 8', 9', 10', 12', 14', 15' 1.5 lbs/ft 2 Regular 1/2" 54" 10', 12' 1.6 lbs/ft 2 Packaging: 2 pieces per bundle, face-to-face, and end labeled. Edge type: Tapered Material Safety Data Sheet: MSDS available at Technical Data Section. 1 Other lengths may be available on a special order basis. Consult with your local PABCO representative, or call PABCO Technical Assistance. 2 Represents approximate weight for design and shipping purposes. A more exact weight may be available for your area; consult with your local PABCO representative, or call PABCO Technical Assistance. Manufacturing: AS C 1396 Federal Specification SS-L-30D Type III & Type VII * Installation: Gypsum Association GA-214 & GA-216, AS C 840, Surface Burning AS E 84 Characteristics: Flame Spread 15, Smoke Developed 0 Noncombustible: AS E 136 R value: 1/2" = 0.45; 3/8" = 0.32 Thermal Resistance VOC/Asbestos: Free of VOC (Volatile Organic Compound) & asbestos PABCO Gypsum: Construction Guide - Fire & Sound Rated Systems Foil Application: Foil may be applied to the back of AS C 1396 gypsum wallboard for the purpose of complying with AS C 1396 paragraph 5.1. Recycled Content: Refer to PABCO Sustainable Materials Data Sheet for plant specific details. Please check our website at for the latest edition of this specification. * The federal specification for gypsum board, SS-L-30d was withdrawn in It is provided here for informational purposes only. Storage & Handling: Store all PABCO gypsum panels flat; do not store on edge as panels are heavy and may fall over causing injury or death. Store in an area that offers protection from adverse weather conditions, condensation, and other forms of moisture. Avoid job site conditions that expose gypsum board to water or moisture. Plastic shipping bags are temporary, and intended for protection during transit only, and must be removed promptly upon arrival. Store gypsum board under protected cover, off the ground with sufficient support to prevent sagging. Exercise proper care to avoid impact, scuffing of the paper faces, undue flexing, and damage to board edges, corners, and ends. Submittal Approvals: Job name: Contractor: Date: Submittal Approvals: Stamps/Signatures Limited Warranty: PABCO Building Products, LLC, warrants that on the date the gypsum board is shipped from its manufacturing plant the gypsum board is free from defects in materials and manufacture. NOTWITHSTANDING THE FOREGOING, IT IS THE RESPONSIBILITY OF THE APPLICATOR TO NOTIFY PABCO BUILDING PRODUCTS, LLC, IN WRITING WITHIN TWENTY FOUR (24) HOURS OF DISCOVERY OF ANY VISIBLY DEFECTIVE PRIOR TO SUCH VISIBLY DEFECTIVE BEING APPLIED; FAILURE TO DO SO MAY FURTHER LIMIT OR VOID THE RESPONSIBILITIES OF PABCO BUILDING PRODUCTS, LLC, UNDER THIS WARRANTY. This warranty will remain in place for one year from the date of shipment from the manufacturing plant. THIS EXPRESS WARRANTY IS THE EXCLUSIVE WARRANTY PROVIDED BY PABCO BUILDING PRODUCTS, LLC, AND SUPERSEDES ANY PRIOR, CONTRARY OR ADDITIONAL REPRESENTATIONS, WHETHER ORAL OR WRITTEN. PABCO BUILDING PRODUCTS, LLC, HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED, OR STATUTORY INCLUDING ANY WARRANTY OF MERCHANTABILITY, ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY IMPLIED WARRANTIES OTHERWISE ARISING FROM COURSE OF DEALING OR USAGE OF TRADE. If the gypsum board fails to conform to the foregoing warranty in Paragraph 1 and such nonconformity is not due to misuse or improper maintenance or storage, Buyer shall notify PABCO Building Products, LLC, in writing, and within 60 days of discovery, PABCO Building Products, LLC, shall provide, at its sole and absolute discretion, one of the following: (i) repair or replacement of any nonconforming or defective gypsum wallboard; or (ii) credit or full refund of the purchase price. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY OF BUYER FOR ANY BREACH OF WARRANTY. IN NO EVENT SHALL PABCO BUILDING PRODUCTS, LLC, BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE, OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT OR FROM NEGLIGENCE OR OTHER TORT. This exclusion applies regardless of whether such damages are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other legal theory. Trademarks: The following trademarks used herein are owned by Pacific Coast Building Products and licensed to PABCO Gypsum: PABCO, PABCORE, FLAME CURB, WATER CURB, MOLD CURB, Quality to the Core, PABCO GLASS, LITECORE and ABUSE CURB Note: Products described herein may not be available in all geographic markets. Consult your PABCO Gypsum sales representative for information. Page #31 SJ-01-28b-13/Regular PABCO Gypsum

9 Submittal a division of PABCO building products, LLC "Quality to the Core" R PABCO LITECORE Gypsum Wallboard for Walls & Ceilings PABCO Gypsum a division of PABCO building products, LLC PO Box Rancho Cordova, CA Technical Services: PABCO Gypsum Specification PGS-015 Manufactured to meet AS C 1396 Section 5 (Gypsum Wallboard), and Section 12 (Gypsum Ceiling Board). LITECORE WALLS & CEILINGS LITECORE WALLS & CEILINGS Description: Primary Uses: Limitations: Advantages: PABCO LITECORE is an interior sagresistant gypsum board product with a noncombustible, dimensionally stable, gypsum core formulated to be lighter than original PABCO Regular wallboard. Each panel is encased in 100% recycled paper on the face and back. The face paper is folded around the long edges to reinforce and protect the core; the ends are square cut and PABCO LITECORE products are utilized in non-structural, non-fire rated wall, ceiling and partition applications, in new construction or renovation work. Because it can be utilized on both walls and ceilings, the need for two PABCO LITECORE panels are intended for interior applications with a maximum framing spacing of 24" o.c. Do not use this product where there will be direct exposure to water or continuous high humidity before, during, and/or after construction. Gypsum panel products shall not be exposed to sustained temperatures exceeding 125 F (52 C). finished smooth. Long edges of panels are tapered providing a recessed area that allows joints to be reinforced and concealed with joint treatment creating a monolithic wall finish. High quality face paper manufactured by PABCO Paper provides a smooth surface which can be decorated with paint, texture or wallpaper. different products is eliminated. This product may be formed to a curve with a short radius, and used as a covering material for flat or curved surfaces. This product is non-structural, non-load bearing, and not to be used as a structural fastener base, or to support heavy wall or ceiling mounted objects. Installation to walls shall be with the bottom edge spaced a minimum of 1/4" inch (6 mm) above the floor. Insulation, when added, shall not exceed 2.2 lbs/sq. ft.. Lighter than regular gypsum wallboard. A strong sag-resistant core allowing installation on walls and ceilings with 24" o.c. steel or wood frame spacing, eliminating the need for two separate products. Non-combustible core, cost efficient, and lightweight. Accepts a wide range of decorative finishes. Consistent edge tapers produce a monolithic flat surface. Easily cut, permitting quick installation, painting and/or decorating. LITECORE WALLS & CEILING Application: PABCO Gypsum endorses the Gypsum Association s publications GA-216 and GA-214 as well as AS Standard Specification C 840 as its application and finishing specifications. These similar specifications give detailed instruction on the standard application of wallboard panels and proper joint finishing procedures. PABCO Gypsum Wallboard panels may be attached to wood or steel framing with nails, screws and/or adhesives. Finishing of joints and covering fasteners is detailed in GA 214 and/or AS C 840. A combination of nails on the perimeters and screws in the field of panels is permitted with the spacing the same as described for each type fastener. PABCO Gypsum Wallboard panels shall be cut to fit as closely as possible without forcing panels in place. Gypsum panel product joints shall be located so that no joint will occur within 12 in. of the corner of an opening unless control joints are to be installed at these locations. Temperature at time of panel application shall be above 40 F and shall be maintained at 50 F 48 hours prior to and during application and drying of joint compound. Special treatment of assemblies for additions such as control joints, resilient channel, insulation and perimeter relief systems shall be as specified in the tested system.

10 Product Data: Sizes and Types Core Thickness Width Length a Weight b LightCore 1/2" 48" 8', 9', 10', 12' 1.5 lbs/ft 2 LITECORE WALLS & CEILINGS LITECORE WALLS & CEILINGS Applicable Standards and Technical Data: Packaging: 2 pieces per bundle, face-to-face, and end labeled. Edge type: Tapered MSDS: Material Safety Data Sheet available at Technical Data a. Other lengths may be available on a special order basis. Consult with your local PABCO representative, or call PABCO Technical Assistance. b. Represents approximate weight for design and shipping purposes. A more exact weight may be available for your area; consult with your local PABCO representative, or call PABCO Technical Assistance. Manufacturing: AS C 1396 Federal Specification SS-L-30D Type III & Type VII * Installation: Gypsum Association GA-214 & GA-216, AS C 840, Surface Burning AS E 84 Characteristics: Flame Spread 15, Smoke Developed 0 Noncombustible: AS E 136 R value: 1/2" = 0.45 Thermal Resistance VOC/Asbestos: Free of VOC (Volatile Organic Compound) & asbestos PABCO Gypsum: Construction Guide - Fire & Sound Rated Systems Foil Application: Foil may be applied to the back of AS C 1396 gypsum wallboard for the purpose of complying with AS C 1396 paragraph 5.1. Recycled Content: Refer to PABCO Sustainable Materials Data Sheet for plant specific details. Please check our website at for the latest edition of this specification. * The federal specification for gypsum board, SS-L-30d was withdrawn in It is provided here for informational purposes only. LITECORE WALLS & CEILINGS Storage & Handling: Submittal Approvals: Store all PABCO gypsum panels flat; do not store on edge as panels are heavy and may fall over causing injury or death. Store in an area that offers protection from adverse weather conditions, condensation, or any forms of moisture. Avoid job site conditions that expose gypsum board to water or moisture. Plastic shipping bags Job name: Contractor: are temporary, and intended for protection during transit only, and must be removed promptly upon arrival. Store gypsum board under protected cover, off the ground with sufficient support to prevent sagging. Exercise proper care to avoid impact, scuffing of the paper faces, undue flexing, and damage to board edges, corners, and ends. Date: LITECORE WALLS & CEILINGS Limited Warranty: PABCO Building Products, LLC, warrants that on the date the gypsum board is shipped from its manufacturing plant the gypsum board is free from defects in materials and manufacture. NOTWITHSTANDING THE FOREGOING, IT IS THE RESPONSIBILITY OF THE APPLICATOR TO NOTIFY PABCO BUILDING PRODUCTS, LLC, IN WRITING WITHIN TWENTY FOUR (24) HOURS OF DISCOVERY OF ANY VISIBLY DEFECTIVE PRIOR TO SUCH VISIBLY DEFECTIVE BEING APPLIED; FAILURE TO DO SO MAY FURTHER LIMIT OR VOID THE RESPONSIBILITIES OF PABCO BUILDING PRODUCTS, LLC, UNDER THIS WARRANTY. This warranty will remain in place for one year from the date of shipment from the manufacturing plant. THIS EXPRESS WARRANTY IS THE EXCLUSIVE WARRANTY PROVIDED BY PABCO BUILDING PRODUCTS, LLC, AND SUPERSEDES ANY PRIOR, CONTRARY OR ADDITIONAL REPRESENTATIONS, WHETHER ORAL OR WRITTEN. Submittal Approvals: Stamps/Signatures PABCO BUILDING PRODUCTS, LLC, HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED, OR STATUTORY INCLUDING ANY WARRANTY OF MERCHANTABILITY, ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY IMPLIED WARRANTIES OTHERWISE ARISING FROM COURSE OF DEALING OR USAGE OF TRADE. If the gypsum board fails to conform to the foregoing warranty in Paragraph 1 and such nonconformity is not due to misuse or improper maintenance or storage, Buyer shall notify PABCO Building Products, LLC, in writing, and within 60 days of discovery, PABCO Building Products, LLC, shall provide, at its sole and absolute discretion, one of the following: (i) repair or replacement of any nonconforming or defective gypsum wallboard; or (ii) credit or full refund of the purchase price. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY OF BUYER FOR ANY BREACH OF WARRANTY. IN NO EVENT SHALL PABCO BUILDING PRODUCTS, LLC, BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE, OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT OR FROM NEGLIGENCE OR OTHER TORT. This exclusion applies regardless of whether such damages are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other legal theory. Trademarks: The following trademarks used herein are owned by Pacific Coast Building Products and licensed to PABCO Gypsum: PABCO, PABCORE, FLAME CURB, WATER CURB, MOLD CURB, Quality to the Core, PABCO LIGHTCORE and ABUSE CURB. Note: Products described herein may not be available in all geographic markets. Consult your PABCO Gypsum sales representative for information. SJ PABCO LITECORE PABCO Gypsum

11 Submittal a division of PABCO building products, LLC "Quality to the Core" R INTERIOR CEILING Sag-Resistant, TE & RE PABCO Gypsum a division of PABCO building products, LLC PO Box Rancho Cordova, CA Technical Services: PABCO Gypsum Specification PGS-006 AS specification C 1396 Available in MOLD CURB Plus to the Description & Primary Uses: PABCO Gypsum Ceiling Board is a 1/2" thick gypsum panel specifically formulated and designed for ceiling application where joist spacing is a maximum of 24"on center. PABCO Gypsum Ceiling Board is manufactured with a sag-resistant engineered core to allow for the application of a water-based texture material when the 1/2" ceiling board is installed on 24" on-center framing. When tested using the AS C 473 humidified deflection test, deflection shall not exceed 50% of the allowable deflection specified for 5/8" thick panels. PABCO Gypsum Ceiling Board is manufactured with a dimensionally stable, noncombustible fire-resistant gypsum core, encased in 100% recycled paper, designed to receive joint treatment, paint, wall covering, or textured coatings. The face paper is folded around the long edges to reinforce as well as to protect the core, and affords a surface suitable for decoration. The panel ends are cut square. The long panel edges are tapered, allowing a recessed joint area to be reinforced and concealed to create a monolithic wall or ceiling finish. PABCO Gypsum Ceiling Board is available in 1/2" thickness, 4 feet wide, 12 and 14 feet long panels, with tapered edges. A Round Edge (RE) profile is available to meet specific joint treatment requirements. Limitations: Maximum spacing between ceiling supports not to exceed 24" on center. PABCO Gypsum Ceiling Board is intended for interior applications only, and shall not be used where there will be direct exposure to water or continuous high humidity before, during, and after construction. Avoid exposure to temperatures exceeding 125 of (52 oc) for an extended period of time. PABCO Gypsum Ceiling Board is a non-structural panel, not to be used as a structural fastener base or to support heavy wall or ceiling mounted objects. PABCO Gypsum Ceiling Board shall be primed and sealed with a high-solids latex primer before the application of texture, or before final decoration. Adequate ventilation is necessary when applying texture to this product. Insulation weight must not exceed 2 lbs/sf. Application: PABCO Gypsum recommends that its Gypsum Ceiling Board be applied and finished to comply with recommendations in GA-216 and/or AS C 840 in a manner similar to PABCO Gypsum Wallboard. Panels shall be applied perpendicular to ceiling framing 24"on center maximum. Page #28