INSTALLATION MANUAL MOSER STAINLESS STEEL KITCHEN FAUCET MODEL MANCHESTER

Transcription

1 INSTALLATION MANUAL MOSER STAINLESS STEEL KITCHEN FAUCET MODEL MANCHESTER

2 Thank you for your purchase of a MoSER faucet. With proper care and maintenance, your new faucet will bring you years of trouble free enjoyment. We welcome any questions or comments you may have and look forward to assisting you. For more information about MoSER Sinks and Faucets products, please visit our website at: To ensure that your installation proceeds smoothly, please carefully read the installation and maintenance instructions. Remember to inspect your faucet for any noticeable damage and verify all parts and pieces are in the box. Verify all local applicable plumbing and building codes. The following instructions are based on application in a residential setting. For the installation of MoSER stainless steel faucets, we suggest using only licensed plumbers. Please note acceptable variances are approximately 1/16 of an inch. Alignment to the pre-drilled hole cut-out and precise application and trimming of any adhesive sealant are critical for a superior fit and finished look. Please take extra care when installing MoSER stainless steel faucet. MoSER does not accept any liability for damage to your countertop, sink fixture, faucets or personal injury during installation. Warranty is void if installation instructions are not properly followed.! Important note: i. Ensure that the cold and hot water lines are turned off. ii. Wrap all threaded connections with Teflon tape. Be sure to always wrap in a clockwise direction. iii. Cover the sink drain to avoid losing parts. iv. Do not disassemble the main faucet body, as it has been precision factory assembled. v. Verify that working pressure is between MPa (including both hot and cold water) and that water temperature is between 4 o C and 90 o C Tools and material you may require: Adjustable Wrench Teflon Tape Silicone Adhesive Rags Eye Protection Phillips Screwdriver Pencil (not ink) Denatured Alcohol»Tape» Measure Be sure to use proper tools and always wear personal safety devices for your protection.! To avoid the risk of fresh water contamination due to back-siphonage, do not connect this faucet to a portable washing device such as a dishwasher.

3 1. Hot and cold waterlines 2. Hose Clip Holder 3. Weight 4. Screws 5. Lock Nut 6. Metal Washer 7. Rubber Ring 8. Faucet Extender 9. O-Ring 10. M15 Adapter 11. Check Valve 12. Washer 13. G1/2 Adapter 14. Washer 15. Finishing Cap 16. M5 Screw 17. Handle 18. Cover 19. Clamp Nut 20. Ceramic Cartridge 21. Faucet Body 22. Gasket 23. O-Ring 24. Plastic Gasket 25. M4 Screw 26. Spout 27. Faucet Head 28. Flex hose 29. Check Valve 30. Nozzle Adapter

4 Faucet Installation: Depending on the distance between the faucet hole and the wall, two installation methods are possible for MoSER faucets with side mounted levers. Method 1 Distance between hole and wall is greater than 3.5 If the distance between the faucet hole and the wall is more than 3.5, a positioning of the faucet lever parallel to the wall is possible. Method 2 - Distance between hole and wall is less than 3.5 If the event the distance between the faucet hole and the wall is less than 3.5, a positioning of the faucet lever 30 degrees to 90 degrees off of the wall may be required to allow for full operation. NOTE If no backsplash is present, make sure to take into consideration the thickness of any future backsplash when determining the distance.

5 STEP 1 Insert faucet body in the pre-drilled 1 3 /8 hole STEP 2 Insert plastic faucet extender (8), shim (7), washer (6), lock nut (5) and lock nut screws (4). NOTE Faucet extender is required when faucet is installed in overmount sinks and optional when installed in solid surface countertops.

6 STEP 3 Use Phillips Screwdriver to tighten lock nut screws. STEP 4 Slip Hose Clip Holder (2) on the end of the flex hose.

7 STEP 5 Secure check valve assembly onto the extending pipe. Tighten with adjustable wrench until snug. Secure the end of the flex hose onto the check valve assembly and tighten with an adjustable wrench until snug. NOTE Ensure O-rings are present in the check valve assembly before connecting to hose and extending pipe. STEP 6 Connect hot and cold waterlines (1) to faucet. Tighten until snug. Install weight (3) approximately 1.18 (30mm) from the lowest point on the hose and tighten screws with a Phillips screwdriver.

8 STEP 7 Wrap Teflon tape to the threaded portion of the shut off valves. Verify if O-rings are present on both ends of the hot and cold waterlines. Connect hot and cold waterlines to the shut off valves. Tighten with an adjustable wrench until snug. Ensure handle is in the off position Turn on water supplies and check for leaks. NOTE In the event longer waterlines than those supplied are required, installer must purchase additional parts separately STEP 8 Turn faucet on and ensure proper flow. Pull out faucet head and look for any leak. Turn faucet off.

9 STEP 9 Remove spray head and hold tip of spray hose. Turn faucet on for 1 minute to flush any debris. Turn faucet off and reconnect spray head. Legal Disclaimer All technical data and information provided in this publication is done as a public service to customers of MoSER Sinks and Faucets (MoSER) and consumers of its products. All names, designs, and model numbers of products are the property of MoSER. Prices and specifications of MoSER products are subject to change without notice or obligation. MoSER may also change or discontinue models of its products without notice or obligation. While MoSER endeavors to provide accurate information and descriptions of its products, accuracy and completeness cannot be guaranteed. MoSER is not responsible for, nor does it have any liability for any mistakes or typographical errors, including liability for incidental, consequential, or special damages. All products should be inspected and measured promptly upon delivery and certainly before any improvements or alterations are done in anticipation of or preparation for installation. MoSER assumes no liability for the use of such information or for any damages incurred through its use or applications. Nothing contained in this publication is to be construed as contractual or providing any form of warranty or representation on the part of MoSER. MoSER MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE, AS TO THE INFORMATION CONTAINED HEREIN OR THE PRODUCTS DESCRIBED HEREIN. mosersinks.com