Notified Body No.: 0575

Transcription

1 DNV GL EC- EXAMINATION CR i IHCATE (MODULE ) Certificate No: MED162 Revision No: 1 Application of: Council Directive 96/98/EC of 2 December 1996 on Marine Equipment as amended by directive (EU) 215/559, issued as "Forskrift om Skipsutstyr" by the Norwegian Maritime Directorate This Certificate is issued by DNV GL AS under the authority of the Government of the Kingdom of Norway This is to certify: That the "A" Class divisions, fire integrity with type designation(s) Steel Deck A-6 Issued to SAINT-GOAIN ISOVER G+H AG Ludwigshafen am Rhein Rheinland-Pfalz, Germany is found to comply with the requirements in the following Regulations/Standards: Annex A1, item No A1/311a and Annex, Module in the Directive; SOLAS 74 as amended, Regulation 11-2/325 and IMO 21 FTP Code Further details of the equipment and conditions for certification are given overleaf This Certificate is valid until Issued at Hovik on DNV GL local station: Approval Engineer: Tessa iever Notified ody No: 575 for DNV GL AS Digitady Signed y: Hoff, lyyind Location: DNV GL Heyik, Norway Signing Date: 76216, on behalf of Vidar Dolonen Head of Notified ody A US Coast Guard approval number will be assigned to the equipment when the production module has been completed and will appear on the production module certificate (module D, E or F), as allowed by the "Agreement between the United States of America and the EEA EFTA states on the mutual recognition of Certificates of Conformity for Marine Equipment" signed 17 October 25 The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production-surveillance module (D, E or F) of Annex of the MED is fully complied with and controlled by a written inspection agreement with a Notified ody The product liability rests with the manufacturer or his representative in accordance with Council Directive 96/98/EC, as amended NCAMMAN ACAMOMON PROO 1 This certificate is valid for equipment, which is conform to the approved type The manufacturer shall inform DNV GL AS of any changes to the approved equipment Should the specified regulations or standards be amended during the validity of this certificate, the product is to be re-approved before being placed on board a vessel to which the amended regulations or standards apply Form code: MED 11NOR Revision: DNV GL 214 DNV GL and the Horizon Graphic are trademarks of DNV GL AS wwwdnvglcom Page 1 of 5

2 Job Id: Certificate No: MED162 Product description "Steel Deck A-6" Construction 1: "U SeaProtect 36/7 + 76/25" Composed of a stiffened steel deck insulated underneath with 7 mm mineral wool of type U SeaProtect 36 (density 36 kg/m3) from SAINT-GOAIN ISOVER G+H AG 25 mm mineral wool of type U SeaProtect 76 (density 76 kg/m3) from SAINT-GOAIN ISOVER G+H AG is fitted around the stiffeners Insulation (U SeaProtect 76) is fitted inside the void of the stiffeners maximum 3 mm Construction 2: "U SeaProtect 36/7 + 36/7" Composed of a stiffened steel deck insulated underneath with 7 mm mineral wool of type U SeaProtect 36 (density 36 kg/m3) from SAINT-GOAIN ISOVER G+H AG 7 mm mineral wool of type U SeaProtect 36 is fitted around the stiffeners Insulation is fitted inside the void of the stiffeners maximum 3 mm Construction 3: "U SeaProtect 66/5 + 76/25" Composed of a stiffened steel deck insulated underneath with 5 mm mineral wool of type U SeaProtect 66 (density 66 kg/m3) from SAINT-GOAIN ISOVER G+H AG 25 mm mineral wool of type U SeaProtect 76 (density 76 kg/m3) from SAINT-GOAIN ISOVER G+H AG is fitted around the stiffeners Insulation (U SeaProtect 76) is fitted inside the void of the stiffeners maximum 3 mm Application/Limitation Approved for use as horizontal fire retarding division of Class A-6 The insulation thickness may be increased up to a maximum area weight of 528 g/m2 Insulation density may be increased up to 66 kg/m3 or a maximum area weight of 528 g/m2 (whichever comes first) The insulation materials and adhesives used have to be approved according to the Marine Equipment Directive and bear the Mark of Conformity This requirement may also be applicable for surface materials used, if required by relevant rules and regulations Each product is to be supplied with its manual for installation and maintenance Form code: MED 11NOR Revision: wwwdnvglcom Page 2 of 5

3 Job Id: Certificate No: MED162 Type Examination documentation Test report no 4P438-1 dated 12 August 214 from SP Technical Research Institute of Sweden, oräs, Sweden (U SeaProtect 36/7 + 76/25) Test report no PGA1521 dated 24 September 214 from Danish Institute of Fire and Security Technology (DI), Hvidovre, Denmark (U SeaProtect 66/5 + 76/25) Assessment report nos PHA1498b (alternative insulation an stiffeners) dated 15 January 215, PHA1498c (minimum thickness and density) dated 13 October 214, PHA1498d (position of joints) dated 16 December 214, PHA1498e (mounting methods for insulation an stiffeners) dated 24 November 214, PHA1498g (pin pattern) dated 28 November 214 All from Danish Institute of Fire and Security Technology (DI), Hvidovre, Denmark Drawing no AK237 (4 pages) dated 11 December 214 from SAINT-GOAIN ISOVER G+H AG Tests carried out Tested according to IMO 21 FTP Code part 3 Marking of product The product or packing is to be marked with name of manufacturer, type designation, fire technical rating, the MED Mark of Conformity and USCG Approval Number if applicable (see page 1) Form code: MED 11NOR Revision: wwwdnvglcom Page 3 of 5

4 Job Id: Certificate No: MED162 Appendix Rev No to MED L A Layout type A immer , U Layout type SAINT-GOARIISOVER Steel Deck Class A-15, A-3 and A-6 General or restricteol Application DrawIng for EC-type exarenneon (Modul CertIfIcate A KÖN, AK237 1/ x 4 WM; L2 b % nover SAINT-GORAINISOVER Steel Deck Class A-15, A-3 and A-6 General or restricted Application Liraring for EC-type exanimation (Modul 5) Certlficate A Kanter "71a311 1' 2/4 Form code: MED 11NOR Revision: wwwdnvglcom Page 4 of 5

5 Job Id: Certificate No: MED162 I 2 I 3 1 I A 46t4 11 % Attedit 44 ti4,» e it )i i \ '1(32(\ A 114, 46 ve 4 4 II, 4 e W ,,, 1, Telb - 6 I e H ' 1 a H 73 3 will, d a P 1_,, r-- - ierter t,_- H ---) :;at tit r - Z5 P e VP! H p : 3 _ E ' e; 1184 F H' - - "('-) H p e -= 41 ie" ISOVer SAINT-GOAIN ISOVER Steel Deck Class A-15, A-3 and A-6 General er restricteol Application Drawing for EC-type examination (Modul ) Certificate A Keder AK237 3/ F Cif Wära H G a db G IG nty when the insulation oh the fat surfale ahoi an -ehe stir-feners is the same 1= 3 1 ISOVer SAINT-GOAIN ISOVER Steel Deck Class A-15, A-3 and A-6 General or restricteol Application Drawing for EC-type examination (Modul 13) Certificate A Runter '' 2,3 11 ' 4/ Form code: MED 11NOR Revision: wwwdnvglcom Page 5 of 5