Hamilton International Air Cargo Logistics Facility Section November 2014 Page 1 of 4

Transcription

1 Hamilton International Air Cargo Logistics Facility Section METAL TOILET COMPARTMENTS Page 1 of 4 Part 1 General 1.1 SECTION INCLUDES.1 Metal toilet compartments, floor mounted. 1.2 RELATED SECTIONS.1 Section Toilet And Bath Accessories. 1.3 REFERENCES.1 ASTM A167 - Stainless and Heat Resisting Chromium-Nickel Steel Plate, Sheet and Strip..2 ASTM A424 - Steel Sheet for Porcelain Enameling..3 ASTM A653/A653M - Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy- Coated (Galvannealed) by the Hot-Dip Process. 1.4 SUBMITTALS.1 Shop Drawings: Indicate partition plan, elevation views, dimensions, details of wall and floor supports and door swings..2 Product Data: Provide data on panel construction, hardware and accessories. 1.5 REGULATORY REQUIREMENTS.1 Conform to applicable code for access for the handicapped. 1.6 FIELD MEASUREMENTS.1 Verify that field measurements are as indicated on shop drawings. 1.7 COORDINATION.1 Coordinate the work with placement of support framing and anchors in wall. Part 2 Products 2.1 ACCEPTABLE MANUFACTURERS.1 Hadrian Manufacturer Ltd..2 Substitutions: as approved by Architect. 2.2 MATERIALS.1 Steel Sheet: ASTM A424, Type I, commercial quality.

2 Hamilton International Air Cargo Logistics Facility Section METAL TOILET COMPARTMENTS Page 2 of ACCESSORIES.1 Pilaster Shoe: Formed chromed steel with satin finish, 75 mm high, with adjustable screw jack..2 Attachments, Screws, and Bolts: Stainless steel; heavy duty extruded aluminum brackets..3 Hardware: Chrome plated non-ferrous cast metal:.1 Pivot hinges, gravity type, adjustable for door close positioning..2 Nylon bearings..3 Thumb turn door latch with exterior emergency access feature..4 Door strike and keeper with rubber bumper..5 Coat hook with rubber bumper..6 Door pull for outswinging doors. 2.4 FABRICATION.1 Fabricate components of steel sheet as follows:.1 Panel and Door Faces: 0.9 mm, 20 gauge..2 Pilaster Faces: 1.2 mm, 18 gauge..3 Reinforcement: 2.5 mm, 12 gauge..2 Doors and Panels:.1 Thickness: 25 mm..2 Door Width: 610 mm..3 Door Width for Handicapped Use: 915 mm, out-swinging..4 Height: mm..3 Pilasters: 32 mm thick, of sizes required to suit cubicle width and spacing..4 Door, Panel and Pilaster Construction: Sheet steel face, pressure bonded to sound deadening core, form and close edges, mitre and weld corners, grind smooth..5 Internal Reinforcement: Provide in areas of attached hardware and fittings. Mark locations of reinforcement for partition mounted washroom accessories. 2.5 FINISHING.1 Clean, degrease and neutralize panels..2 Follow immediately with a phosphatizing treatment, prime coat and two finish coats baked enamel..3 Single Colour: Hadrian/ 621 Slate/ Powder Coated.4 Stainless Steel Surfaces: No. 4 finish.

3 Hamilton International Air Cargo Logistics Facility Section METAL TOILET COMPARTMENTS Page 3 of 4 Part 3 Execution 3.1 EXAMINATION.1 Verify correct spacing of and between plumbing fixtures..2 Verify correct location of built-in framing, anchorage and bracing. 3.2 INSTALLATION.1 Install partitions secure, rigid, plumb, and level in accordance with manufacturer's instructions..2 Maintain 9 to 13 mm space between wall and panels and between wall and end pilasters..3 Attached panel brackets securely to walls using anchor devices..4 Attach panels and pilasters to brackets with tamper proof through bolts and nuts..5 Install 760 mm, mm high stainless steel protective splash panels on partitions adjacent to urinals. Fasten with stainless steel screws spaced 20 mm on centre..6 Provide adjustment for floor variations with screw jack through steel saddles integral with pilaster. Conceal floor fastenings with pilaster shoes..7 Support pilasters from built-in framing using two adjustable hanging studs providing vertical leveling. Conceal ceiling fastenings with pilaster shoe..8 Equip each door with two hinges, one door latch, one coat hook and bumper; outswinging door with pull..9 Install door strike and keeper with door bumper on each pilaster in alignment with door latch..10 Field touch-up of scratches or damaged enamel finish will not be permitted..11 Replace damaged or scratched materials with new materials. 3.3 ERECTION TOLERANCES.1 Maximum Variation From True Position: 6 mm..2 Maximum Variation From Plumb: 3 mm. 3.4 ADJUSTING.1 Adjust and align hardware to uniform clearance at vertical edge of doors, not exceeding 5 mm..2 Adjust hinges to position doors in partial opening position when unlatched. Return out swinging doors to closed position.

4 Hamilton International Air Cargo Logistics Facility Section METAL TOILET COMPARTMENTS Page 4 of 4.3 Adjust adjacent components for consistency of line or plane. END OF SECTION

5 Chamberlain Architect Services Limited Page 1 of 5 Part 1 General 1.1 SECTION INCLUDES.1 Toilet, shower and washroom accessories..2 Grab bars..3 Attachment hardware. 1.2 RELATED SECTIONS.1 Section Ceramic Wall Tiling: Ceramic accessories..2 Section Metal Toilet Compartments. 1.3 REFERENCES.1 ASTM A123/A123M - Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products..2 ASTM A167 - Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet and Strip..3 ASTM A269 - Seamless and Welded Austenitic Stainless Steel Tubing for General Service..4 ASTM A1008/A1008M - Steel, Sheet, Cold-Rolled Carbon, Structural, High- Strength Low Alloy and High Strength Low Alloy with Improved Formability..5 ASTM B456 - Electrodeposited Coatings of Copper Plus Nickel Plus Chromium and Nickel Plus Chromium. 1.4 SUBMITTALS.1 Shop Drawings: Indicate partition plan, elevation views, dimensions, details of wall, and ceiling supports, door swings..2 Product Data: Provide data on panel construction, hardware, and accessories..3 Manufacturer's Installation Instructions: Indicate special procedures, perimeter conditions and requiring special attention. 1.5 REGULATORY REQUIREMENTS.1 Conform to applicable code for access for the handicapped. 1.6 FIELD MEASUREMENTS.1 Verify that field measurements are as instructed by the manufacturer.

6 Chamberlain Architect Services Limited Page 2 of COORDINATION.1 Coordinate the work with the placement of internal wall reinforcement and to receive anchor attachments. Part 2 Products 2.1 MANUFACTURERS.1 Refer to schedule.2 Manufacturers offering equivalent products..1 Bobrick Washroom Equipment, Inc..2 Hafele America Co. (HEWI).3 American Specialties, Inc. (ASI).4 Gamco, A Bobrick Company.3 Substitutions: as approved by Architect. 2.2 MATERIALS.1 Sheet Steel: ASTM A Stainless Steel Sheet: ASTM A167, Type 304. Unless shown otherwise, all exposed stainless steel to have a #4 Satin finish or Satin chrome finish where applicable with all elements of a unit to have brushing in one direction.3 Tubing: ASTM A269, stainless steel..4 Fasteners, Screws, and Bolts: Hot dip galvanized, tamper-proof and security type..5 Expansion Shields: Fibre, lead, or rubber as recommended by accessory manufacturer for component and substrate..6 Exposed surfaces to be protected with a factory applied PVC film to be left in place until final clean-up. 2.3 FABRICATION.1 Weld and grind joints of fabricated components, smooth..2 Form exposed surfaces from single sheet of stock, free of joints. Form surfaces flat without distortion. Maintain surfaces without scratches or dents..3 Fabricate grab bars of tubing, free of visible joints, return to wall with end attachment flanges. Knurl grip surfaces..4 Shop assemble components and package complete with anchors and fittings..5 Provide steel anchor plates, adapters, and anchor components for installation.

7 Chamberlain Architect Services Limited Page 3 of KEYING.1 Supply two (2) keys for each accessory to Owner..2 Master key all accessories. 2.5 FINISHES.1 Galvanizing: ASTM A123 to [380] g/sq m. Galvanize ferrous metal and fastening devices..2 Shop Primed Ferrous Metals: Pre-treat and clean, spray apply one coat primer and bake..3 Enamel: Pre-treat to clean condition, apply one coat primer and minimum two coats epoxy electrostatic baked enamel..4 Chrome/Nickel Plating: ASTM B456, Type SC 2 satin finish..5 Stainless Steel: No. 4 satin luster finish..6 Back paint components where contact is made with building finishes to prevent electrolysis. Part 3 Execution 3.1 EXAMINATION.1 Verify that site conditions are ready to receive work and dimensions are as instructed by the manufacturer..2 Verify exact location of accessories for installation. 3.2 PREPARATION.1 Deliver inserts and rough-in frames to site for timely installation..2 Provide templates and rough-in measurements as required. 3.3 INSTALLATION.1 Install accessories in accordance with manufacturers' instructions and ANSI A Install plumb and level, securely and rigidly anchored to substrate.

8 Chamberlain Architect Services Limited Page 4 of 5 SCHEDULE Item Description Manufacturer/Model Toilet Tissue Dispenser Satin Stainless Steel. Support-arm flanges lock to concealed stainless steel wall pate. Chrome-plated plastic spindle holds rolls up to 5½ (140mm) diameter(1800 sheets). Unit (320 x 50mm) projects 100mm Bobrick B-6867 Surface Mounted Paper Towel Dispenser/ Waste Receptacle Soap Dispenser Feminine Napkin Dispenser Seat-Cover Dispenser Sanitary Napkin Disposal Mirrors Grab Bars from wall. Satin-finish stainless steel. Door has 90 degree return, conceals flange. Dispenses 800 multifold or 1100 single-fold towels. Removable, leakproof, 24-L waste container. Rough wall opening: 290 x 1360 x 145mm. Corrosion-resistant valve dispenses commercially marketed all-purpose hand soaps. Container is satin-finish Type 316 stainless steel. Capacity: 1.2L. 178 x 156 x 84mm. 355mm W x 710mm H. Flat door design with 90 degree return to conceal flange. Push-button operation. Empty product indicator automatically blocks coin slot. Holds 30 tampons, 20 napkins. Two tumbler door locks keyed like other Bobrick accessories. Separately keyed coin box lock for management access. Type 304 satin-finish stainless steel on exposed surfaces. Satin-finish stainless steel. Dispenses 250 single- or half foldedtoilet seat covers. Fills from bottom. Unit 400 x 285 x 55mm. Satin-finish stainless steel. Cover is drawn, one-piece construction; secured to cabinet with full-length stainless steel piano-hinge. Capacity: 3.8L. 190 x 255 x 95mm. 610 x 914 mm. One-piece 13 x 13 x 9.5mm channel-frame. Type 430 stainless steel with bright-polished finish. Mitered corners. No. 1 quality, 6mm glass mirror. Galvanized steel back. Secured to concealed wall hanger with theft-resistant mounting. 760mm & 610mm long, 32mm dia. Tubing. Constructed of 18 gauge (1.2mm), type 304 satin-finish Bobrick B-3803 Trim Line Series Recessed Bobrick Contura Series Surface Mounted Bobrick B Trim Line Series Recessed Bobrick B-4221 Bobrick B-270 Contura Series Surface Mounted Bobrick B Bobrick B-5806 x 30, B-5806 x 24

9 Chamberlain Architect Services Limited Page 5 of 5 stainless steel tubing. Concealed mounting flange 3mm thick, type 304 stainless steel plate (50 x 80mm), with screw holes for concealed anchors. Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 85mm diameter. Cover snaps over mounting flange to conceal screws. Clothes Hook 11-gauge (3.2mm), type 304 stainless steel, satin finish. Hook is 30 x 30mm and projects 30mm from Bobrick B-233 Hat and Coat Hook (Intended for towel/ clothes hanging) Hook Strip Shelf wall. Unit is 55mm high. Bright-polished stainless steel. Flange is 50 x 50mm. Hook 25 x 165mm; projects 80mm from wall. Concealed wall plate. Type 304 stainless steel, satin finish. Hooks are 25 x 165mm; project 55mm from wall. Mounting strip is 100mm high and has 6mm return. Type 304, 18-gauge (1.2mm) stainless steel with satin finish. 19mm return edges for maximum rigidity. Front edge is hemmed for safe handling. Mounting brackets are type 304, 16-gauge (1.6mm) stainless steel with satin finish. Welded to back return of shelf and secured inside front hem of shelf. Unit 455 x 205mm. Bobrick B-682 Bobrick B-232 x 24 Bobrick B-298 END OF SECTION