ASSEMBLY INSTRUCTIONS

Transcription

1 ASSEMBLY INSTRUCTIONS 8mm CURVED GLASS DOOR FOR OFFSET(EXTENDED) ITEMS,DECIDE WHICH HAND IS REQUIRED BEFORE INSTALLATION. V06/06/2014

2 BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION 1) General Information Please inspect this product upon delivery. any missing parts or manufacturing defects must be reported immediately to the supplier. Damage of defects reported later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS-AVOID HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE. Glass breakage claims will not be accepted after the product has been unpacked. Please note--alumimium is a soft metal, and undergoes a series of extrusion. fabrication, polishing and anodising processes in order to create your finished shower enclosure. Some light surface marks are normal, and is a result of the manufacturing processes. Quality control has ensured that this item is of a good standard, and is fit for purpose. 2) Addition notes Please read these instructions carefully before starting installation. Special care should be taken when drilling walls to avoid hidden pipes or electrical cables. Note: this product is heavy and may require two people to install. TOOLS REQUIRED DESCRIPTION PART IMAGE DESCRIPTION PART IMAGE Tape measure Drill Spirit level Flat-head Screwdriver Pencil Cross head Screwdriver Ø6mm Drill bit Hammer Ø3mm Drill bit Silicone Sealant This product is heavy and may require two people to install. 1

3 ASSEMBLY INSTRUCTIONS-DRAWING (28) (27) (26) (25) (24) (23) (22) (21) (20) (19) (18) (1) (2) (3) (4) (17) (16) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (1) (2) (3) (4) (5) 8x Wall Plugs 2x Wall Posts 8x Screws 4x30 (Pan Head) 6x Screw Cover Cap Washers 6x Screws 4x12 (11) (12) (13) 2x Bottom Seals 1xDrip Strip 2x Moving Doors (14) 2x Screw Cover Caps (15) 2x Screws 4X30 (Round Head) (21) (22) (23) (24) (25) 4x Screws (Sink Head) 2x Washers(Top Rail) 2x Glass Fixing Part A 2x Glass Fixing Part B 1x Guide Rail (6) (7) (8) (9) 6x Screw Cover Caps 2x Fixed Panels 2x Vertical Seal(Fixed Panel) 2x Bottom Guide Blocks (16) (17) (18) (19) 2x Magnet Seals 2x Handles 2x Cover Caps(Wall Post) 2x Cover Caps(Vertical Profile) (26) (27) (28) 3x Door Stops 4x Rollers 4x Safety Knobs (10) 2x Vertical Seal (Moving Door) (20) 2x Cover Caps(Top Rail) 2

4 ASSEMBLY INSTRUCTIONS If you require help, we advise you firstly contact a competent plumber Installation Steps Step 1 THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL R550 3

5 Step 2 MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS SHOWER PANEL / DOOR. Take care not to damage wall surface x4 x4 6mm x4 x4 Ø6mm x4 15 x4 4x30 x4 x4 4x30 Step 3 4

6 Step 4 Make sure the glass frame is now central between the wall profiles Step 5 x2 Ø3mm x2 x2 x2 x2 5

7 Step 6 Step 7 6

8 Step 8 Step 9 x6 How to adjust the width of the Quad Maximum adjustment x6 Glass panel Vertical profile Wall profile A A Wall x6 Minimum 10mm internal overlap required Minimum adjustment x6 Glass panel Vertical profile Wall profile Wall Take care not to drill to the glass 7

9 Step 10 Step 11 Silicone Silicone INSIDE VIEW INSIDE VIEW 8

10 Step 12 A B Step 13 A B 9

11 Step 14 Silicone (outside edge only) where the vertical profiles meet the wall, and the fixed glass panels meet the tray 10

12 CARE AND MAINTENANCE 1) AFTER CARE INSTRUCTIONS Regularly clean your shower product with warm soapy water to prevent lime scale build up. Do not use abrasive cleaning fluids or materials, or strong chemical cleaners as this will damage the product surface. 2) MAINTENANCE Clean the plastic parts with a cloth and mild detergent. Never use any abrasive creams, dissolvents, acetone or detergents and disinfectants that contain chlorine. The supplier accepts no liability for any type of use of care other than those contained in these instructions. The supplier reserves the right to introduce technical changes without notice. COMMITMENT TO QUALITY It is our intention that the quality and functions of this product are of the highest standard. If you require help we advise you firstly contact a competent plumber. However we understand that this may not always be the case, so should you experience any problems please contact out customer services quoting the following: Product name: 8mm Quad Enclosure Product code: QDD8008 QDD9008 OQD1288 OQD1298 Customer help line number:

13 HFLQ888/ HFLQ888R/ HFLQ899/HFLQ899R, KEY6157, SPA

14 The packaging you have received with your product is 100% recyclable. It must be disposed of in a safe and environmentally friendly way. We suggest you take it to the local landfill site and discard in the designated bins.