PRODUCT CATALOGUE. Your repair is our care HUWA ROMACON ROMACON PETRO GEKAVE HEGAWA

Transcription

1 1 PRODUCT CATALOGUE HUWA Your repair is our care ROMACON ROMACON PETRO GEKAVE HEGAWA HEGAWA KERKDIJK-ZUID 11A 5492 HW SINT-OEDENRODE P.O. BOX AD SINT-OEDENRODE THE NETHERLANDS T +31 (0) F +31 (0) E HEGAWA@HEGAWA.NL HUWA KERKDIJK-ZUID 11A 5492 HW SINT-OEDENRODE P.O. BOX AD SINT-OEDENRODE THE NETHERLANDS T +31 (0) F +31 (0) E SALES@HUWA.COM HEGAWA HUWA

2 X United Pipeline Products 3 is ready for the future Our machinery has been up-dated and our entire building is equipped with all the latest environmentally friendly technologies: Left: Twan van Heesch and right: Piet van de Warenburg As a group we also ensure that our products meet the current international standards for drinking water pipes, gas supply, repair clamps, we use only high quality stainless steel ets and flanges company. Our experienced staff is educated and fully trained to help customers solve all possible issues related to pipe repair and hot tapping as well as providing useful advice. Our special products division has skilled and certified welders that guarantee high quality results for our specially engineered products. At the same time we moved to a new location and united our forces, we also streamlined and adjusted production processes where necessary. INTRODUCTION After years of integration and relocations, we would now sector in which our independent businesses operate. Since 19 November 2010, United Pipeline Products has been made up of the following companies: in response to the changing international environment in the water, gas, oil and energy markets. independently, since this has proved very successful over the future.

3 HUWA ON THE JOB HUWA REPAIR CLAMP SNAP 5 HUWA Snap Clamps are used for the permanent repair of damaged pipes above ground uids Following types of damage can be repaired: Cracks / Local damage Pit holes Application: Snap Clamps provide a fast and economic repair to small damages in pipes up to DN 300. They are applied on board of ships and by plumbers for repairs above ground. The rubber partially covers the inside of the band and allows the repair of small holes caused by corrosion or frost. The clamps can be used on following pipe types: - Ductile Iron (DI) - Copper - Cast Iron (CI) - Steel (St.) Pressure ratings: - Pipe OD mm 16 bar - Pipe OD mm 10 bar - Pipe OD mm 6 bar Maximum pressure for gas pipes is 4 bar (for all pipe od's up to incl. 329 mm) Available sizes: Snap Clamps are available for pipes up to DN 300 and length 75, 150 and 225 mm. We will send you a price-list with all available ranges upon request. For larger ranges we can supply double band snap clamps. cation: Lugs: ductile iron GGG 40 acc. to Din 1693 or malleable iron GTW 40 acc. to Din 1692, surface sheradized with 15 microns zinc. Band: stainless steel acc. to AISI 304. Bolts: special mushroom head square neck bolts. Bolt size M10 up to 2 and M12 for larger sizes. Material acc. to class 4.6, surface galvanized with 5 microns zinc. Hexagon nuts: acc. to Din 934 class 5, surface galvanized with 5 microns zinc. Washer: acc. to Din 125a, surface galvanized with 5 microns zinc. Rubber (standard): waed EPDM, NBR on request; acc. to ISO gas and water pipelines.

4 HUWA REPAIR CLAMP TYPE HUWA-Q 7 HUWA stainless steel repair clamps style HUWA-Q are used for permanent repairs of damaged pipes uids Following types of damage can be repaired: Cracks / Local damage Pit holes The HUWA-Q Clamp is designed for pipes of DN 20 up to and including DN 200 HUWA-Q clamps can be used as an economical alternative to HUWA-10 clamps, but only for local damages. The clamps can be used to repair the following pipe types: - Ductile Iron (DI) - PE coated steel - Cast Iron (CI) - PVC* - Steel (St.) - GRP* - Asbestos Cement (AC) - PE* * If pipe repair clamps are to be used on plastic pipes, please always contact HUWA or a HUWA distributor for more information regarding the application and restrictions on these pipe types. Available sizes: HUWA-Q clamps are available in several dierent working ranges for pipes of DN 20 up to and including DN 200. Please consult our price-list for more details on the working ranges. Available lengths: 100 / 150 and 200 mm. Pressure ratings: Pressure ratings for water ** depend on the type of break or damage, pipe OD, medium etc. In general, HUWA-Q clamps can resist a working pressure of 16 bar for pipes up to DN 150 and 10 bar for pipes with DN > 150. cation: All metal parts: stainless steel AISI 304. Metal parts have been deburred and are passivated to restore the corrosion resistance to its original state after the welding process. Single band (one section) half circle clamp with a working range between 4 and 11 mm, depending on the diameter. For an overview of all working ranges please see our price-list. ed rubber gaskets EPDM or NBR. The rubber is tapered and has a wae pattern. U-shaped lifter bar. Stainless steel, electrolytic zinc plated nuts to prevent galling. Stainless steel washers. No loose parts that may get lost during installation. No special tools required: a simple wrench will do the job. x the rubber gasket to exible bre thread to withstand hot and humid conditions and guarantee a long storage capability. Under most circumstances the clamps can be installed without releasing the pressure on the pipe. The clamps are packed into strong double-rib cartons. For export overseas we use strong, seaworthy crates Available rubber gaskets: HUWA-Q clamps can be supplied with the following types of rubber: EPDM EPDM HT NBR ed to European standards, such as ACS (France) and WRAS (UK). Please contact us for a detailed list of current cations. - natural gas VITON - several chemicals pls. contact HUWA max 60 degr. C. max 150 degr. C. max 70 degr. C. max 200 degr. C. ** Please contact HUWA or your distributor for more information regarding pressures on gas pipes.

5 HUWA REPAIR CLAMP TYPE HUWA-QS 9 HUWA stainless steel repair clamps style HUWA-QS are used for permanent repairs of broken and damaged pipes uids Following types of damage can be repaired: Pipe longitudinal connection Damage due to broken pipes Longitudinal crack Cracked pipe after hot tap Misaligned pipes The clamps can be used to repair the following pipe types: - Ductile Iron (DI) - PE coated steel - Cast Iron (CI) - PVC* - Steel (St.) - GRP* - Asbestos Cement (AC) - PE* * If pipe repair clamps are to be used on plastic pipes, please always contact HUWA or a HUWA distributor for more information regarding the application and restrictions on these pipe types. HUWA repair clamps should be used under following conditions: - For PVC pipes, the width of the clamps should be 50 % longer and bolt torque should be reduced by 50 %. We prefer that you consult your HUWA distributor. - The maximum allowable distance between two pipe ends should not exceed 10 mm. - The maximum ection is 2 degrees. - The maximum allowable oset should not exceed 3 mm. The HUWA-QS repair clamp is in fact a small version of the HUWA-10 repair clamp, having a range of max. 4 mm. The clamp is used on pipes for which HUWA-10 clamps are not available due to the small pipe diameter. cation: All metal parts: stainless steel AISI 304. Metal parts have been deburred and are passivated to restore the corrosion resistance to its original state after the welding process. Single band (one section) with a workingrange of max. 4 mm. For an overview of all working ranges please see our price-list. ed rubber gaskets EPDM or NBR. The rubber is tapered and has a wae pattern. Seamless rubber lining for every clamp diameter. Bridge plate is vulcanized into the rubber gasket. U-shaped lifter bar. Stainless steel, electrolytic zinc plated nuts to prevent galling. Stainless steel washers. No loose parts that may get lost during installation. No special tools required: a simple wrench will do the job. x the rubber gasket to exible bre thread to withstand hot and humid conditions and guarantee a long storage capability. Under most circumstances the clamps can be installed without releasing the pressure on the pipe. The clamps are packed into strong double-rib cartons. For export overseas we use strong, seaworthy crates Available sizes: HUWA-QS clamps are available in several dierent working ranges from to Please consult our price-list for more details on the working ranges. Available lengths: 75, 100 and 150 mm. Pressure ratings: Pressure ratings for water ** depend on the type of break or damage, pipe OD, medium etc. In general, HUWA-QS clamps can resist a working pressure of 16 bars. ** Please contact HUWA or your distributor for more information regarding pressures on gas pipes. Available rubber gaskets: HUWA-QS clamps can be supplied with the following types of rubber: EPDM NBR - natural gas The vulcanized bridge plate guarantees a leakproof sealing ed to European standards, such as ACS (France) and WRAS (UK). Please contact us for a detailed list of current cations. max 60 degr. C. max 70 degr. C. HUWA-QS is available for pipe nominal diameters 1/2" up to 2". Pit holes Available length 75, 100 and 150 mm

6 HUWA REPAIR CLAMP TYPE HUWA HUWA stainless steel repair clamps style HUWA-10 are used for permanent repairs of broken and damaged pipes uids Following types of damage can be repaired: Pipe Longitudinal connection Damage due to broken pipes Longitudinal cracks Cracked pipe after hot tap Misaligned pipes The clamps can be used to repair the following pipe types: - Ductile Iron (DI) - PE coated steel - Cast Iron (CI) - PVC* - Steel (St.) - GRP* - Asbestos Cement (AC) - PE* * If pipe repair clamps are to be used on plastic pipes, please always contact HUWA or a HUWA distributor for more information regarding the application and restrictions on these pipe types. HUWA repair clamps should be used under following conditions: - The width of the clamp should be equal to at least the pipe OD. - The width of the clamp should be 150 mm greater than the length of any crack on pipes with an outside diameter up to 350 mm. On larger pipes this should be at least 200 mm. - For PVC pipes, the width of the clamps should be 50 % longer and bolt torque should be reduced by 50 %. We prefer that you consult your HUWA distributor. - The maximum allowable distance between two pipe ends should not exceed 10 mm. - ection is 2 degrees. - The maximum allowable oset should not exceed 3 mm. cation: All metal parts: stainless steel AISI 304 or AISI 316L. Metal parts have been deburred and are passivated to restore the corrosion resistance to its original state after the welding process. Single band (one section) with a working range of 7-11 mm depending on the diameter. For an overview of all working ranges please see our price-list. ed rubber gaskets EPDM or NBR. The rubber is tapered and has a wae pattern. Seamless rubber lining for every clamp diameter. Bridge plate is vulcanized into the rubber gasket. U-shaped lifter bars. Stainless steel, electrolytic zinc plated nuts to prevent galling. Stainless steel washers. No loose parts that may get lost during installation. No special tools required: a simple wrench will do the job. x the rubber gasket to the exible and reinforced bre thread to withstand hot and humid conditions and guarantee a long storage capability. Under most circumstances the clamps can be installed. without releasing the pressure on the pipe. The clamps are separately packed into strong double-rib cartons. For export overseas we use strong, seaworthy crates. Other: Also available with grip for easier installation. Available sizes: HUWA-10 clamps are available in many dierent working ranges for pipes of DN 40 - DN 350. Please consult our price-list for more details on the working ranges. Available lengths: 150 / 200 / 250 / 300 / 400 / 500 / 600 mm. Pressure ratings: Pressure ratings for water ** depends on the type of break or damage, pipe OD, medium etc. Pipe DN 40 up to and including DN 150: 16 bar Pipe DN 175 up to and including DN 300: 10 bar ed to cope with higher working pressures. ** Please contact HUWA or your distributor for more information regarding pressures on gas pipes. Available rubber gaskets: The vulcanized bridge plate guarantees a leakproof sealing. Huwa-10 clamps can be supplied with the following types of rubber: EPDM EPDM HT NBR ed to European standards, such as ACS (France) and WRAS (UK). Please contact us for a detailed list of current cations. - natural gas VITON - several chemicals pls. contact HUWA max 60 degr. C. max 150 degr. C. max 70 degr. C. max 200 degr. C. Pit holes

7 HUWA REPAIR CLAMP TYPE HUWA HUWA stainless steel repair clamps style HUWA-20 are used for permanent repairs of broken and damaged pipes uids Following types of damage can be repaired: Pipe Longitudinal connection Damage due to broken pipes Longitudinal cracks Cracked pipe after hot tap Misaligned pipes The clamps can be used to repair the following pipe types: - Ductile Iron (DI) - PE coated steel - Cast Iron (CI) - PVC* - Steel (St.) - GRP* - Asbestos Cement (AC) - PE* * If pipe repair clamps are to be used on plastic pipes, please always contact HUWA or a HUWA distributor for more information regarding the application and restrictions on these pipe types. HUWA repair clamps should be used under following conditions: - The width of the clamp should be at least equal to the pipe OD. - The width of the clamp should be 150 mm greater than the length of any crack on pipes with an outside diameter up to 350 mm. On larger pipes this should be at least 200 mm. - For PVC pipes, the width of the clamps should be 50 % longer and bolt torque should be reduced by 50 %. We prefer that you consult your HUWA distributor. - The maximum allowable distance between two pipe ends should not exceed 10 mm. - ection is 2 degrees. - The maximum allowable oset should not exceed 3 mm. cation: All metal parts: stainless steel AISI 304 or AISI 316L. Metal parts have been deburred and are passivated to restore the corrosion resistance to its original state after the welding process. Double band (two sections) with a working range of mm depending on the diameter. For an overview of all working ranges please see our price-list. ed rubber gaskets EPDM or NBR. The rubber is tapered and has a wae pattern. Seamless rubber lining for every clamp diameter. Bridge plates are vulcanized into the rubber gasket. U-shaped lifter bars. Stainless steel, electrolytic zinc plated nuts to prevent galling. Stainless steel washers. No loose parts that may get lost during installation. No special tools required: a simple wrench will do the job. x the rubber gasket to the exible and reinforced bre thread to withstand hot and humid conditions and guarantee a long storage capability. Under most circumstances the clamps can be installed. without releasing the pressure on the pipe. The clamps are separately packed into strong double-rib cartons. For export overseas we use strong, seaworthy crates. Other: Also available with grip for easier installation. Available sizes: HUWA-20 clamps are available in many dierent working ranges for pipes of DN 80 - DN 800. Please consult our price-list for more details on the working ranges. Available lengths: 200 / 250 / 300 / 400 / 500 / 600 mm. Pressure ratings: Pressure ratings for water ** depends on the type of break or damage, pipe OD, medium etc. Pipe DN 80 up to and including DN 150: 16 bar Pipe DN 175 up to and including DN 500: 10 bar ed to cope with higher working pressures. ** Please contact HUWA or your distributor for more information regarding pressures on gas pipes. Available rubber gaskets: The vulcanized bridge plate guarantees a leakproof sealing HUWA-20 clamps can be supplied with the following types of rubber: EPDM EPDM HT NBR ed to European standards, such as ACS (France) and WRAS (UK). Please contact us for a detailed list of current cations. - natural gas VITON - several chemicals pls. contact HUWA max 60 degr. C. max 150 degr. C. max 70 degr. C. max 200 degr. C. Pit holes

8 HUWA REPAIR CLAMP TYPE HUWA HUWA stainless steel repair clamps style HUWA-30 are used for permanent repairs of broken and damaged pipes uids Following types of damage can be repaired: Pipe Longitudinal connection The clamps can be used to repair the following pipe types: - Ductile Iron (DI) - PE coated steel - Cast Iron (CI) - PVC* - Steel (St.) - GRP* - Asbestos Cement (AC) - PE* * If pipe repair clamps are to be used on plastic pipes, please always contact HUWA or a HUWA distributor for more information regarding the application and restrictions on these pipe types. cation: All metal parts: stainless steel AISI 304 or AISI 316L. Metal parts have been deburred and are passivated to restore the corrosion resistance to its original state after the welding process. Triple band (three sections) with a working range of mm depending on the diameter. For an overview of all working ranges please see our price-list. ed rubber gaskets EPDM or NBR. The rubber is tapered and has a wae pattern. Seamless rubber lining for every clamp diameter. Bridge plates are vulcanized into the rubber gasket. U-shaped lifter bars. Stainless steel, electrolytic zinc plated nuts to prevent galling. Stainless steel washers. No loose parts that may get lost during installation. No special tools required: a simple wrench will do the job. x the rubber gasket to the exible and reinforced bre thread to withstand hot and humid conditions and guarantee a long storage capability. Under most circumstances the clamps can be installed without releasing the pressure on the pipe. The clamps are separately packed into strong double-rib cartons. For export overseas we use strong, seaworthy crates. The vulcanized bridge plate guarantees a leakproof sealing Available sizes: HUWA-30 clamps are available in many dierent working ranges for pipes of DN DN Please consult our price-list for more details on the working ranges. Available lengths: 300 / mm. Other lengths possible on request. If you need to repair larger pipes we can oer 4 band or 5 band clamps. Please contact us for more information. Pressure ratings: Pressure ratings for water ** depend on the type of break or damage, pipe OD, medium etc. Pipe DN 250 up to and including DN 500: 10 bar Pipe DN 500 and DN 600: 6 bar Pipe DN 700: 4 bar and Pipe DN 800: 2 bar. Please consult our price-list for working pressures of ed to cope with higher working pressures. ** Please contact HUWA or your distributor for more information regarding pressures on gas pipes. Damage due to broken pipes Longitudinal cracks Cracked pipe after hot tap HUWA repair clamps should be used under following conditions: - The width of the clamp should be at least equal to the pipe OD. - The width of the clamp should be 150 mm greater than the length of any crack on pipes with an outside diameter up to 350 mm. On larger pipes this should be at least 200 mm. - For PVC pipes, the width of the clamps should be 50 % longer and bolt torque should be reduced by 50 %. We prefer that you consult your HUWA distributor. - The maximum allowable distance between two pipe ends should not exceed 10 mm. - ection is 2 degrees. - The maximum allowable oset should not exceed 3 mm. Other: Also available with grip for easier installation. Available rubber gaskets: HUWA-30 clamps can be supplied with the following types of rubber: EPDM EPDM HT NBR - natural gas VITON - several chemicals pls. contact HUWA max 60 degr. C. max 150 degr. C. max 70 degr. C. max 200 degr. C. Misaligned pipes ed to European standards, such as ACS (France) and WRAS (UK). Please contact us for a detailed list of current cations. Pit holes

9 HUWA EMERGENCY REPAIR SET CLAMP COMBINATIONS 17 HUWA 10 (one part): Part Length Plate Clamp Length Min. OD Range Max. OD A B C HUWA stainless steel Emergency Repair sections are used for the permanent repair of damaged pipes uids HUWA 20 (two parts): Part A D 543 E 637 Combined with Length Plate B 700 Clamp Length Min. OD 213 Range Max. OD 233 C Application: Working pressure: D 860 E The function of the Emergency repair set is to reduce the stock that has to be carried by the water companies and to improve the availability of clamps in case of emergency repairs. The pressure for which the clamp can be used varies with the number of sections, pipe diameter, medium etc. Use the following table as a guide: B C 829 D 926 E Especially for larger repair clamps that are relatively seldom used, it is convenient to have the combi repair clamp available so that any required clamp with a diameter between 91 and 780 mm can be assembled from the sections of the combi repair clamp. The sections are packed in a wooden crate and each time that two or more sections are used, the used sections can be re-ordered to complete the crate for the next emergency. The sections, which increase in size, are marked A,B,C,D and E. Standard length is 400 mm Clamp combinations: nd the right combination of clamp sections for the range you need. Nominal working pressure under ideal circumstances. pipe od for water for gas Bar 6 Bar Bar 4 Bar Bar 3 Bar Bar 1 Bar Bar 0,5 Bar Bar 0,5 Bar Available rubber gaskets: HUWA-ERS clamps can be supplied with the following types of rubber: EPDM EPDM HT NBR ed to European standards, such as ACS (France) and WRAS (UK). Please contact us for a detailed list of current cations. - natural gas VITON - several chemicals pls. contact HUWA max 60 degr. C. max 150 degr. C. max 70 degr. C. max 200 degr. C. C D HUWA 30 (three parts): Part A B C D 989 E 1083 E Combined with HUWA 40 (four parts): Part A C Length Plate B and C 1146 B and D 1243 B and E 1337 C and D 1306 Clamp Length Min. OD Range Max. OD 384 C and E D and E C and D 1327 C and E 1466 D and E 1563 D and E Combined with Length Plate B,C and D 1689 B,C and E 1783 B,D and E 1880 Clamp Length Min. OD Range Max. OD 567 D,E and A B C,D and E HUWA 50 (five parts): Part Combined with Length Plate Clamp Length Min. OD Range Max. OD A B,C,D and E

10 HUWA INTERNAL REPAIR CLAMP HUWA SPLIT BARREL 19 HUWA internal repair clamps are used for permanent repairs of broken and damaged pipes from the inside. uids The HUWA split barrel repair clamp is used to repair leaking couplings, broken AC couplings, leaking bell joint connections and high pressure pipes. With the split barrel repair clamp it is possible to repair the pipe without removing the broken coupling. Furthermore it can be easily installed even under rough and wet conditions. No special tools are needed, only a torque wrench. The clamp is suitable for pressures up to 40 bar and on pipes with a diameter up to 1500 mm and length up to mm. The HUWA internal repair clamp oers a cost & labour eective permanent repair solution for the renewal of leaking pipes, in order to conserve water and to protect the environment. The problem: Leakage of pipe joints in the stormwater and sewage watertransportation is a known - and costly fact! The consequences of water loss result in increased pumping & energy cost, including maintenance and lost revenues. Sewage leakage will not only contaminate the surroundings but the waste is also not being transported for proper treatment. The solution: In order to resolve these damaging liabilities concering the ecology, HUWA has found a very simple and functional method, after a two year research program. An ingenious, internal stainless steel repair clamp which is suitable for waste water piping has been designed and tested. The application: The HUWA internal repair clamp can be installed inside pipes of various materials. -20 inch / 500 mm. - or larger - le on the external side of the rubber gasket will ensure a complete sealing surface between the expansion sections and the pipeline to be repaired. ed internal sealing procedure are made of stainless steel 316L quality material and are fully passivated. A very solid and functional expansion system takes care of the proper distribution of the forces on the rubber seal, so that a perfect sealing wil be created. cations Material: stainless steel aisi 304/316. Bolts and nuts: Stainless steel aisi 304/316 with PTFE coating - to avoid galling. Rubber gaskets: NBR or EPDM. Axial gaskets are seated in grooves in each half of the split barrrel. owing out during installation. The initial radial seal is obtained by tightening the end bolts at each end of the barrel. Depending on the size and weight of the product, a hinge construction will be provided to lift the split barrel over the pipe. A vent is installed for testing purpose and to enable the medium to escape during installation. A suitable vent valve is not included. How to order or request prices ll out the "split barrel size request form". This form provides us with all the necessary details to make the quotation and, at a later stage, manufacture the product. We will need to know the pipe diameter, repair situation, pressure and medium as well as the required length. If possible please provide us with a sketch or picture of the repair situation. During the installation of the stainless steel sections one only has to use a screwdriver and a ratchet wrench. In other words, no complicated and costly equipment or installation time is required. The HUWA internal repair clamp has a low amount of parts and is light weight which is an appreciated and welcome feature during installing expansion procedures. ow characteristics can be maintained.

11 HUWA DRILLING SADDLE TYPE RVZ 21 HUWA stainless steel drilling saddle style HUWA-RVZ are used for making connections to valves, t-joints (branch pipes), shut-o valves, pipe ttings, etc. uids Application of the HUWA stainless steel drilling saddle: The HUWA stainless steel drilling saddle can be supplied with special branch pipes (among others, POLVA and branch pipes with male and female threading). cation: All metal parts: stainless steel AISI 304 or AISI 316L. Metal parts have been deburred and are passivated to restore the corrosion resistance to its original state after the welding process. Double band (two sections) with a working range of mm depending on the diameter. For an overview of all working ranges please see our price-list. ed rubber gaskets in the upper scale is NBR, EPDM on request. This rubber is tapered and has a wae pattern. Band gasket is always EPDM. Seamless rubber lining for every clamp diameter. U-shaped lifter bars. Stainless steel, electrolytic zinc plated nuts to prevent galling. Stainless steel washers. No loose parts that may get lost during installation. No special tools required: a simple wrench will do the job. Under most circumstances the clamps can be installed without releasing the pressure on the pipe. Installation details on drilling saddle to prevent wrong installation on site. Available sizes: HUWA-RVZ drilling saddles are available in many dierent working ranges for pipes of DN 80 - DN 350. Please consult our price-list for more details on the working ranges. Length: 150 mm. Pressure ratings: Pressure ratings for water ** depend on the type of break or damage, pipe OD, medium etc. Pipe DN 40 up to and including DN 150: 16 bar Pipe DN 175 up to and including DN 300: 10 bar ** Please contact HUWA or your distributor for more information regarding pressures on gas pipes. Available sizes of the HUWA stainless steel drilling saddle: The HUWA stainless steel drilling saddle can be supplied with branch sizes starting at 1/2" to 2". Special branch sizes can be supplied on request. The saddle can be supplied onwards from DN 80 to DN 350. We can also supply the required branch pipes for blow-forming equipment applications. Available rubber gaskets: HUWA drilling saddles can be supplied with the following types of rubber: NBR - natural gas max 70 degr. C. EPDM max 60 degr. C. Details: ed to European standards, such as ACS (France) and WRAS (UK). Please contact us for a detailed list of current cations.

12 HUWA TAPPING CLAMPS 23 HUWA stainless steel tapping clamps are used to make permanent (hot) taps on dierent pipe types uids HUWA tapping clamps can be equipped with a threaded outlet up to 4". The clamp specications are identical to the specications of the HUWA standard repair clamps. The standard outlets are threaded according to ISO/ DIN or BSP. American CC or IP threads can be supplied upon request. The clamps can be used to repair the following pipe types: - Ductile Iron (DI) - PE coated steel - Cast Iron (CI) - PVC* - Steel (St.) - GRP* - Asbestos Cement (AC) - PE* Size of the threaded outlet or nipple Available on pipe Ø 1/2 " 38mm 150 3/4 " 44mm " 45mm /4 " 60mm /2" 60mm " 82mm /2 " * 110mm " * 130mm " * 155mm 400 Minimum width in mm * Only available on double band clamps, with a reinforced upper scale cation: All metal parts: stainless steel AISI 304 or AISI 316L. Sockets and nipples are threaded according to ISO 7/DIN or BSP. Special designed outlets are available on request. Please contact your distributor. The outlets are 100 % air tested after welding. Metal parts have been deburred and are passivated to restore the corrosion resistance to its original state after the welding process. Single band (one section) or double band (two sections). For detailed working ranges please see our price-list. ed rubber gaskets EPDM or NBR. The rubber is tapered and has a wae pattern. Seamless rubber lining for every clamp diameter. Bridge plate is vulcanized into the rubber gasket. U-shaped lifter bars. Stainless steel, electrolytic zinc plated nuts to prevent galling. Stainless steel washers. No loose parts that may get lost during installation. No special tools required: a simple wrench will do the job. x the rubber gasket to the exible and reinforced bre thread to withstand hot and humid conditions and guarantee a long storage capability. Under most circumstances the clamps can be installed without releasing the pressure on the pipe. Available sizes: HUWA 10 tapping clamps are available from range Available lengths: 150 / 200 / 250 / 300 / mm. HUWA 20 tapping clamps are available from ranges Available lengths: 200 / 250 / 300 / mm. Pressure ratings: Pressure ratings for water ** depend on the type of break or damage, pipe OD, medium etc. Pipe DN 40 up to and including DN 150: 16 bar Pipe DN 175 up to and including DN 300: 10 bar ed to cope with higher working pressures. ** Please contact HUWA or your distributor for more information regarding pressures on gas pipes. Available rubber gaskets: HUWA clamps can be supplied with the following types of rubber: EPDM EPDM HT NBR ed to European standards, such as ACS (France) and WRAS (UK). Please contact us for a detailed list of current cations. - natural gas Viton - several chemicals pls contact HUWA max 60 degr. C. max 150 degr. C. max 70 degr. C. max 200 degr. C. * If pipe tapping clamps are to be used on plastic pipes, please always contact HUWA or a HUWA dis tributor for more information regarding the applica tion and restrictions on these pipe types.

13 HUWA TAPPING TEE TYPE HUWA-T 25 HUWA stainless steel tapping tee type HUWA-T are used for permanent (hot) taps on several pipe types uids anged outlet. The standard working range is 20mm. The upper body is reinforced to accomodate the installation of valves and drilling equipment. Design advantages oered by the HUWA-T tapping sleeve: Inventory reduction: t various classes of steel, PVC, ductile iron, cast iron or asbestos-cement pipe. Easy installation: No specially trained personnel or tools needed. A wrench to tighten bolts is the only tool required to install the sleeve. Full circumferentia seal: dence. No more need for heavy, hard to assemble, cast iron sleeves. Material: Stainless steel AISI 304 or 316 L. Light weight: The high tensile strength of stainless steel allows us to manufacture the lightest tapping sleeve in the industry. easy to handle and less load on the pipe. Reinforces pipe: Full circle design reduces stress on the pipe opposite of the tap. cation: All metal parts: stainless steel AISI 304 or AISI 316L. Metal parts have been deburred and are passivated to restore the corrosion resistance to its original state after the welding process. Double band (two sections). For detailed working ranges please see our price-list. ed rubber gaskets EPDM or NBR. The rubber is tapered and has a wae pattern. Seamless rubber lining for every clamp diameter. Bridge plates are vulcanized into the rubber gasket. U-shaped lifter bars. Stainless steel, electrolytic zinc plated nuts to prevent galling. Stainless steel washers. No loose parts that may get lost during installation. No special tools required: a simple wrench will do the job. x the rubber gasket to the exible and reinforced bre thread to withstand hot and humid conditions and guarantee a long storage capability. The HUWA-T tapping sleeve is designed for under pressure drilling (hot taps). Pressure ratings (for water): Pressure ratings depend on the type of pipe, branch OD, medium etc. In general, HUWA-T tapping Tees are for use on pipes up to and including DN 600 mm and can resist a pressure of 16 bar. Please contact HUWA or your distributor for more information regarding pressures on gas pipes. Flange design: Flanges are drilled acc. to DIN 2576 and NEN The anges up to DN 200 and anges at faced PN 10, but raised faced, ASA and PN 16 anges are available upon request. ange size the branch can be supported by an additional reinforcement. Pipe and valve should always be supported according to standard codes of practice. Size on size tapping sleeves require the use of an undersized shell cutter. Please ask your distributor for more information. The HUWA-T sleeve can be used to repair the following pipe types: - Ductile Iron (DI) - PE coated steel - Cast Iron (CI) - PVC* - Steel (St.) - GRP* - Asbestos Cement (AC) - PE* * If pipe repair clamps are to be used on plastic pipes, please always contact HUWA or a HUWA distributor for more information regarding the application and restrictions on these pipe types. Available sizes: HUWA-T tapping tee clamps are available for pipe diameters from DN 80 up to DN 800. Standard length: 500 mm. Besides our standard program, we are able to manufacture any range or length that you may require. Available rubber gaskets: HUWA clamps can be supplied with the following types of rubber: EPDM EPDM HT NBR - natural gas Viton - several chemicals pls contact HUWA ed to European standards, such as ACS (France) and WRAS (UK). Please contact us for a detailed list cations. max 60 degr. C. max 150 degr. C. max 70 degr. C. max 200 degr. C.

14 HUWA Z-COMBI ALIGNMENT SADDLE (ZC) OTHER SADDLE SOLUTIONS 27 HUWA Z-combi alignment saddles are used to make permanent (hot) taps on existing or new pipe lines for water and gas pipes Characteristics of the HUWA ZC saddle Solid, well thought-out construction. - High quality GGG 50 ductile iron. - Produced according to DIN 3543, Part 1. - Saddle is provided with epoxy coating, EWS epoxy according GSK-diridives RAL-G2-662 DVGW- W-270, which prevents rust. DVGW (G87 e 087) approved. Perfect seal through flat O-ring, which is enclosed in the chamber of the alignment saddle (see illustration). Through a special combination of O- ring and flat ring, a two-fold seal is obtained. Rubber for ring gasket is NBR. - Applicable for various types of material, such as asbestos-cement, cast iron and steel. Very suitable for pipes covered with polyethylene. When the HUWA ZC Saddle is placed, the polyethylene layer does not have to be removed. Test report upon request. Wide, 100% stainless steel lower bracket. Lower bracket provided with a special rubber band. Stainless steel, electrolytic zinc plated nuts, to prevent fretting. Saddles available from DN 40 up to including DN 600. Suitable for alignments under pressure. Applications of the HUWA ZC Saddle The HUWA ZC Saddle can be used to make taps on all pipe types except PE for water and gas applications. This saddle is ideal for pipes covered with polyethylene, but also fits old pipes perfectly. Dimensions of the HUWA ZC Saddle The HUWA ZC Saddle can be supplied with a tapped service outlet of 1/2 up to and including 2. Special service outlets are available upon request. The HUWA ZC Saddle can be supplied from DN 40 up to and including DN 600. Strap width 60 mm available with branch according to Polva 1 1/2 to 2. DN in mm Working Range On Request

15 HUWA INSERTS TOOLS 29 x K Torque Wrench: HUWA stainless steel inserts are used to reinforce PE and PVC pipes from the inside to allow the use of compression couplings HUWA inserts are designed to reinforce pipe ends by providing inside support for PE or PVC pipes when pipe couplings or ange adaptors are used for the connection of these pipes. The inserts are supplied with a wedge to overcome the tolerances in the plastic pipes Its thin wall construction will not disturb the ow characteristics of the medium. Inserts are made of stainless steel AISI 304. PE pipe size length 63 x 3, x 5,8-5, x 8, x 4, x 6,8-6, x 10, x 2,7-2, x 5,4-5, x 8,2-7, x 12, x 6,6-6, x 10,0-9, x 15, x 3,7-3, x 7,4-7, x 11,4 175 PE pipe size length 140 x 12, x 8, x 4,5-3, x 9,5-9, x 14, x 6, x 10,7-10, x 16, x 6, x 11,9-11, x 18, x 6,3-5, x 13,4-12, x 20,5 225 PE pipe size length 250 x 9, x 14,8-14, x 22, x 8, x 16,6-15, x 25, x 9, x 12, x 17, x 18, x 28,6 225 * Please contact HUWA or a HUWA distributor for more information regarding bigger pipe size Inserts. Controlled screw tightening in the most widely used range of tightening on mechanical joints, repair clamps, sleeves, service ange bolts, couplings and hydrants with a range of Nm or lbf. - For use in almost all industrial manufacturing areas. - Release system triggers a tactile and audible signal for perfect installation. - Sturdy, satin chrome-plated tubular steel design, with chrome-plated ratched head and high-quality synthetic components. - Dual scale Nm and lbf below a window with a magnifying glass eect. Deep Socket Set: The Deep Socket set contains 4 socket sizes that help to fasten the most common nut sizes on mechanical joints, repair clamps, ange bolts, couplings and hydrants. Large diameter barrels make fast hand tightening easy. Operates with any 1/2" drive manual or impact wrench. Deep sockets are available individually or in a set. x K Torque Wrench. DoubleShot Wrench Set: exibility in dealing with the most common nut sizes that fasten mechanical joints, repair ange bolts, couplings and hydrants. All of the DoubleShot wrenches have the Bolt-Thru design that lets bolts pass entirely through sockets and arm head so nuts can be secured on any threaded length. They are therefore perfect for installing all of our products. DoubleShot wrenches are available individually or in sets. cally for pipeline, utility, maintenance and construction workers. nd. - Switch located in head reverses action safely and conveniently. - Heavy duty stamped, riveted handle; sockets made of rugged cast metal. Both the handle and socket are coated with electrostatic epoxy paint for durability and easy cleaning. - Each wrench is 34 cm long and weighs 1 kg. - Vinyl grip makes working with this product comfortable and secure. - Guaranteed against defects in material and workmanship for 1 year from delivery date.

16 OTHER PRODUCTS HEGAWA 31 Pipe cleaning strap: Prepares surfaces prior to cutting and drilling. Unique circular blades cut in every direction, allowing free movement of the strap. The pipe cleaning strap is manufactured using anti static belting, which ensures safety when working on any pipeline especially those carrying ammable materials. The cleaning strap is standard, is suitable for cleaning mains up to 12" diameter, however longer versions for larger diameter pipes are available upon request. The user-friendly handles incorporate a shortening device, which allows the operator to reduce the length of the cleaning strap to suit the diameter of the main being cleaned. The handles incorporate a anti-spin handle which is kind to the operators hands. Attached to the anti static belt is a number of specially hardened cleaning buttons. Unlike other models, the HUWA pipe cleaning Strap incorporates cleaning teeth which are circular in design which enables each button to create a cutting action in BOTH directions cleaning the pipe quicker and easier than conventional models. Each circular tooth will also revolve whilst cutting ensuring the full surface area of the tooth is utilised. for pipeline systems become a major supplier of pipeline connection products to the water and gas, shipbuilding and building industries. joints and expansion joints. specially made products, such as gripping couplings and flange adaptors, dismantling joints and expansion joints up to Hegawa is your supplier of the complete range of pipeline this business and have a deep understanding of the problems supply a complete solution that will give our customers the advantages of having one supplier for all the connections they need. Frits Berben, Managing Director Hegawa B.V. For more information please visit our website

17 HEGAWA 33

18 HEGAWA 35

19 HEGAWA 37

20 HEGAWA 39

21 HEGAWA 41

22 HEGAWA 43

23 HEGAWA 45

24 HEGAWA 47

25 HEGAWA 49

26 HEGAWA 51 METAALUNIE CONDITIONS General delivery and payment conditions of Koninklijke Metaalunie (the Dutch organisation for small and medium-sized enterprises in the metal industry), referred to as the METAALUNIE CONDITIONS, formerly referred to as the SMECOMA CONDITIONS, filed with the Court Registry in Rotterdam on 1 January Published by Koninklijke Metaalunie, PO Box 2600, 3430 GA Nieuwegein, the Netherlands. Koninklijke Metaalunie Article 1: Applicability 1.1. These Terms & Conditions apply to all tenders issued by members of Koninklijke Metaalunie, to all agreements concluded by those members and to all agreements that may result therefrom The tendering party/supplier is the Metaalunie member applying these Terms & Conditions, and is referred to as the Supplier. The counterparty is referred to as the Client In the event of any conflicts between the substance of the agreement concluded between the Client and the Supplier on the one hand and these Terms & Conditions on the other, the provisions set out in the agreement have precedence These Terms & Conditions may only be used by members of Koninklijke Metaalunie. Article 2: Tenders 2.1. No obligations are attached to any tenders If the Client supplies the Supplier with data, drawings etc., the Supplier may rely on their accuracy and shall base the tender on that information All prices specified in the tender are based on delivery ex works, in accordance with the Incoterms Prices are stated exclusive of VAT and packing materials If the tender is not accepted, the Supplier is entitled to charge the Client for all costs incurred in order to submit the tender. Article 3: Intellectual property rights 3.1. Unless agreed otherwise in writing, the Supplier retains the copyrights and all industrial property rights to all tenders, designed submitted, illustrations, drawings, trial models, programs, etc The rights listed in Article 3.1 remain the property of the Supplier, regardless of whether costs have been charged to the Client for their production. The relevant information may not be copied, used or shown to third parties without the Supplier s explicit prior consent. The Client will be liable to pay the Supplier a penalty for each instance of violation of this provision, to the amount of 25,000. This penalty may be demanded in addition to any compensation damages awarded by law The Client must return all data provided as meant in Article 3.1 on demand, within the period specified by the Supplier. If this provision is violated, the Client is liable to pay the Supplier a penalty of 1,000 per day. This penalty may be demanded in addition to any compensation damages awarded by law. Article 4: Advice, designs and materials 4.1. The Client cannot derive any rights from advice or information provided by the Supplier that has no direct bearing on the engagement The Client is responsible for all drawings, calculations and designs made by or on behalf of the Client, and for the functional suitability of all materials prescribed by or on behalf of the Client The Client indemnifies the Supplier for any claims from third parties arising in connection with the use of the drawings, calculations, designs, materials, samples, models, etc. provided by or on behalf of the Client The Client may examine (or arrange for the examination of) the materials that the Supplier intends to use before they are processed, at the Client s own expense. Any damages incurred by the Supplier as a result are for the Client s expense. Article 5: Delivery times 5.1. The delivery deadline and/or work period stated by the Supplier are estimates In determining delivery deadlines and/or work periods, the Supplier assumes that the engagement can be carried out under the circumstances as they are known to the Supplier at that moment Delivery deadlines and/or work periods do not commence until the Parties have agreed on all commercial and technical details, all necessary data, final and approved drawings, etc. are in the Supplier s possession, the payment or instalment agreed has been received and the conditions necessary for the performance of the engagement have been met a. In the event of circumstances that are different to those known to the Supplier when the delivery deadline and/or work period were determined, the Supplier may extend the delivery deadline and/or work period by the time that is required in order to perform the engagement under those circumstances. If the work cannot be fitted into the Supplier s work schedule, it will be carried out as soon as the Supplier s schedule permits. b. In the event of contract extras, the delivery deadline and/or work period will be extended by the time required to supply (or arrange for the supply of) the materials and parts necessary for those contract extras and to carry out the contract extras. If the contract extras cannot be fitted into the Supplier s work schedule, they will be carried out as soon as the Supplier s schedule permits. c. In the event that the Supplier s obligations are suspended, the delivery deadline and/or work period will be extended by the duration that the obligations are suspended. If resumption of the work cannot be fitted into the Supplier s work schedule, the work will be carried out as soon as the Supplier s schedule permits. d. In the event of weather conditions that prevent work being carried out, the delivery deadline and/or work period will be extended by the resulting delay If the delivery deadline and/or work period agreed is exceeded, that circumstance does not in any instance entitle the Client to compensation for damages, unless agreed in writing. Article 6: Transfer of risk 6.1. Deliveries are made ex works, in accordance with the Incoterms 2000; the risks attached to the object are transferred at the moment that the Supplier makes the object available to the Client The provisions of Article 6.1 notwithstanding, the Client and the Supplier may agree that the Supplier will arrange transport. The risks attached to the storage, loading, transport and unloading remain with the Client in such instances. The Client may take out insurance to cover those risks In the event that objects are to be exchanged and the Client continues to use the exchangeable object while awaiting delivery of the new object, the risks attached to the exchangeable object remain with the Client until the moment that possession of the object has been relinquished to the Supplier. Article 7: Price changes 7.1. The Supplier may charge any increases in cost-determining factors that arise after the agreement is concluded to the Client if the performance of the agreement has not been completed at the moment of the increase The Client is obliged to pay the price increases as meant in Article 7.1 at the same time as the principal sum or the next instalment is paid If the Client provides goods and the Supplier is prepared to use those goods, the Supplier may charge up to 20% of the market price of the goods provided. Article 8: Impracticability of the engagement 8.1. The Supplier is entitled to suspend the fulfilment of any obligations if any circumstances that could not be foreseen when the agreement was concluded and that are beyond the Supplier s influence temporarily prevent the fulfilment of those obligations Circumstances that the Supplier could not foresee and that are beyond the Supplier s influence are understood to include (but are not limited to) the circumstance that the Supplier s own suppliers and/or subcontractors fail to meet their obligations, or fail to do so in time, the weather, earthquakes, fire, loss or theft of tools, the destruction of materials to be processed, road blocks, strikes or work stoppages and restrictions on import or trade The Supplier is no longer entitled to suspend the fulfilment of any obligations when the temporary impossibility of performance has lasted for more than six months. The agreement may not be dissolved until that term has lapsed, and only in respect of those obligations that have not been fulfilled. In that event, the Parties are not entitled to any compensation for damages incurred as a result of that dissolution. Article 9: Scope of the work 9.1. The Client is responsible for ensuring that all licences, permits, dispensations and other administrative decisions that are needed to carry out the work are obtained in time The price for the work does not include the following: a. the costs of earthwork, pile driving, demolition, foundation work, cementing, carpentry, plastering, painting, wallpapering, repairs or other construction work; b. the costs of connecting gas, water, electricity or other infrastructural facilities; c. the costs of preventing or limiting damages to any objects situated on or near the work site; d. the costs of disposing of materials, building materials or waste products; e. hotel and travelling expenses. Article 10: Changes to the work Any changes to the work will result in contract variations in at least the following instances: a. if the design or the specifications change; b. if the information provided by the Client does not match the actual situation; c. in the event of deviation from estimated quantities by more than 10% Contract extras will be charged based on the value of the cost-determining factors as at the moment that the contract extra is performed. Contract deductions will be settled based on the value of the cost-determining factors as at the moment that the agreement was concluded If the value of the contract deductions exceeds that of the contract extras, the Supplier is entitled to charge the Client for 10% of the difference upon final settlement. This provision does not apply to any contract deductions based on requests from the Supplier. Article 11: Performance of the work The Client is responsible for ensuring that the Supplier can carry out the activities without interruption and at the times agreed, and that the Supplier has access to the necessary facilities when carrying out the activities, such as: - gas, water and electricity; - heating; - lockable and dry storage space; - all facilities required by the laws and regulations governing working conditions The Client is liable for all damages, including those resulti ng from loss, theft, burning or harm, to objects belonging to the Supplier, the Client and/or any third parties, such as tools and materials intended for use in the work that are located on the site where the activities are carried out or at another agreed location If the Client fails to fulfil the obligations as set out in Article 11.1 and 11.2, and that failure causes delays in the performance of the activities, the activities will be carried out as soon as the Client as yet fulfils those obligations and when the Supplier s schedule permits. The Client is liable for all damages that the Supplier incurs as a result of the delay. Article 12: Completion of the work The project will be deemed to have been completed when: a. the Client has approved the work; b. the Client has put the work into use. If the Client puts part of the work into use, that part will be deemed to have been completed; c. the Supplier has notified the Client in writing that the work is finished and the Client has not communicated, within 14 days after than notification, whether or not the work has been approved; d. the Client does not approve the work on grounds of minor defects or missing parts that can be repaired or provided within 30 days and that do not prevent the work from being put into use If the Client does not approve the work, the grounds on which the approval is withheld must be communicated to the Supplier in writing If the Client does not approve the work, the Supplier must be given another opportunity to complete the work. The provisions set out in this Article apply anew The Client indemnifies the Supplier against all claims from third parties for damages to parts of the work that have not yet been completed that are caused by use of parts of the work that have already been completed. Article 13: Liability The Supplier is liable for all damages that the Client incurs that stem directly and exclusively from a shortcoming attributable to the Supplier. However, only those damages for which the Supplier is insured, or should within reason have been insured, qualify for compensation If, when the agreement is concluded, it is impossible for the Supplier to take out insurance as meant in Article 13.1, or impossible to do so at reasonable conditions, or if it is subsequently impossible to renew the insurance policy at reasonable conditions, the maximum compensation payable for damages is the amount that the Supplier charged for the agreement in question (exclusive of VAT) The following damages do not qualify for compensation: a. trading losses, including losses caused by delays and loss of profits. The Client should take out insurance to cover such damages, if such is deemed desirable; b. supervision damages, which are understood to include damages caused, during or as a result of the performance of the work, to objects on which work is being carried out to objects situated in the vicinity of the work site. The Client should take out insurance to cover such damages, if such is deemed desirable; c. damages caused by intent or gross negligence on the part of helpers or non-management employees of the Supplier The Supplier is not liable for damages to materials provided by or on behalf of the Client that result from improper processing. At the Client s request, the Supplier will repeat the process, using materials provided by the Client, at the Client s expense The Client indemnifies the Supplier against all claims from third parties for product liability stemming from defects in products provided by the Client to third parties that consisted of or included products and/or materials provided by the Supplier. Article 14: Guarantees The Supplier guarantees the proper performance of the product or service stipulated for a period of six months after delivery or completion If the product or service stipulated consists of contract work, the Supplier guarantees the soundness of the construction delivered and the materials used, if the Supplier was at liberty to choose those materials, for the period specified in Article If the construction delivered and/or the materials used prove to be unsound, the Supplier will make the necessary repairs or replacement. Those parts that are to be repaired at the Supplier s place of business or are to be replaced by the Supplier must be sent to the Supplier carriage paid. Disassembly and assembly of those parts, plus any hotel and travelling expenses, are for the Client s account If the product or service stipulated (partly) consists of the processing of materials provided by the Client, the Supplier guarantees proper processing for the period specified in Article If any processing proves to have been performed improperly, the Supplier will do one of the following, at the Supplier s discretion: - repeat the process, in which case the Client must provide new materials, at the Client s own expense; - repair the shortcoming, in which case the Client must return the materials to the Supplier carriage paid; - credit the Client for a proportionate part of the invoice If the product or service stipulated consists of the delivery of an object, the Supplier guarantees the soundness of the object delivered for the period specified in Article If the delivery proves to have been defective, the object must be returned to the Supplier carriage paid. The Supplier will then elect either: - to repair the object; - to replace the object; - to credit the Client for a proportionate part of the invoice If the product or service stipulated (partly) consists of the fitting and/or assembling of a delivered object, the Supplier guarantees the soundness of the fitting and/or assembly for the period specified in Article If the fitting and/or assembly prove to be defective, the Supplier will repair the fault. Any hotel and travelling expenses are for the Client s account Factory guarantees apply to those parts for which the Client and the Supplier agree such explicitly and in writing. If the Client has had the opportunity to examine the substance of the factory guarantee, that factory guarantee will replace the guarantees specified in this Article In all situations, the Client must allow the Supplier the opportunity to repair any shortcomings and/or repeat the processing The Client may only invoke guarantees after all obligations in respect of the Supplier have been fulfilled a. No guarantee is given when defects are the result of: - normal wear and tear; - improper use; - lack of proper maintenance; - fitting, assembly, alterations or repairs by the Client or by third parties. b. No guarantee is given for delivered objects that were not new when they were delivered of for objects whose use the Client prescribed or that were provided by or on behalf of the Client. c. No guarantee is given on inspections of and/or repairs to objects belonging to the Client. Article 15: Complaints The Client may not invoke defects in the product or service unless a written complaint has been submitted to the Supplier within fourteen days after the defect was detected or should, within reason, have been detected. Article 16: Failure to take delivery In the event that the Client has not taken delivery of any object after the delivery deadline has passed, those objects will remain available to the Client. Any objects of which the Client has not taken delivery will be stored for the Client s account and risk. The Supplier may at any time invoke the powers granted by Article 6:90 of the Dutch Civil Code. Article 17: Payment Payment must be made at the Supplier s place of business or to an account specified by the Supplier Unless agreed otherwise, payment must be made using one of the following methods: a. for counter sales: cash; b. for payment in instalments: - 40% of the total price when the engagement is granted; - 50% of the total price when the materials have been delivered or, if the engagement does not include delivery of the materials, upon commencement of the activities; - 10% of the total price upon completion; c. in all other instances: within thirty days after the date on the invoice The payment conditions specified notwithstanding, the Client is obliged, at the Supplier s request, to provide security for payment, to the Supplier s satisfaction. Failure on the Client s part to provide such security for payment within the period specified will immediately constitute default. In that event, the Supplier is entitled to dissolve the agreement and recover any damages from the Client The Client s right to offset any claims on the Supplier is excluded, except in the event of the Supplier s bankruptcy or if judicial debt rescheduling is applied in respect of the Supplier The full claim for payment is payable on demand in the following instances: a. if any payment deadline has been exceeded; b. if the Client has been declared bankrupt or requests suspension of payments; c. if any of the Client s assets or claims are seized; d. if the Client (if a company) is dissolved or wound up; e. if the Client (if a natural person) makes a request for judicial debt rescheduling, is placed under guardianship or dies If payment has not been made by the payment deadline specified, the Client is immediately liable to pay the Supplier interest. That interest is payable at a rate of 12% per year, or at the statutory rate if that is higher. For the purposes of calculating the interest, partial months are counted as full months If payment has not been made by the payment deadline specified, the Client is immediately liable to pay the Supplier all extrajudicial costs, to a minimum of 75. The costs are calculated in accordance with the following table: over the first 3,000 15% over the excess up to 6,000 10% over the excess up to 15,000 8% over the excess up to 60,000 5% over the excess from 60,000 3% If the actual extrajudicial costs exceed those based on this formula, the Client is liable to pay the actual costs If judicial proceedings are decided in the Supplier s favour, all costs incurred by the Supplier in connection with those proceedings are for the Client s account. Article 18: Retention of ownership and pledging After delivery, the Supplier remains the owner of the objects delivered for as long as: a. the Client fails or will fail in the fulfilment of the obligations stemming from this agreement or any similar agreements; b. the Client fails or will fail to pay for any work performed or to be performed under such agreements; c. the Client has not paid any claims arising from nonfulfilment of those agreements, such as compensation for damages, penalties, interest and costs As long as any objects are subject to retention of ownership, the Client may not encumber those objects in any way that exceeds the scope of the Client s ordinary activities Having invoked retention of ownership, the Supplier may retrieve the objects delivered. The Client must allow the Supplier to enter the place where those objects are located If the Supplier cannot invoke retention of ownership because the objects delivered have been subject to confusion, deformation or accession, the Client is obliged to give the newly formed objects in pledge to the Supplier. Article 19: Termination If the Client wishes to dissolve the agreement without the Supplier having failed in the performance thereof and if the Supplier so agrees, the agreement will be terminated by mutual consent. In that event, the Supplier is entitled to reimbursement for all financial losses incurred, such as damages, loss of profits and costs. Article 20: Applicable law and competent court These Terms & Conditions are governed by the laws of the Netherlands The Vienna Sales Convention (C.I.S.G.) does not apply to these Terms & Conditions, nor do any other international regulations whose exclusion is permitted Only the Dutch civil court within whose jurisdiction the Supplier s place of business is situated is competent to pass judgment on disputes, unless such is at odds with any mandatory rules of law. The Supplier is entitled to deviate from this jurisdiction clause and apply the statutory rules for jurisdiction The Parties may agree on another form of dispute settlement, such as arbitration or mediation. These conditions are a full translation of the Dutch version of the METAALUNIEVOORWAARDEN as deposited with the Registry of the District Court in Rotterdam on 1 January Explanation and interpretation of the text of these Conditions shall be based on the Dutch text.