Thermo Proof installation system

Transcription

1 IAL SE AL A N T EC SP Thermo Proof installation system UD INCL ED Z Heavy-duty distance installation for ETICS, clinker or on flat roofs Aqua-Stop provides effective protection from façade rotting due to damp Stainless steel prevents unattractive spots of rust Approval for use by the construction supervisory authority Practically no energy loss Simple and speedy installation You Tube.com/toxgermany www. Infinitely adjustable Iso-Spacer insulation sleeve For insulation up to 200 Description & application Thermo Proof is a heavy-duty distance installation system for heat insulated façades (ETICS) comprising: Iso-Spacer with large support surface and SW24 drive for improved transfer of force Aqua-Stop special sealant for outside use; incl. dosing tip; 80ml capacity; transparent in colour Steel parts made from rust-free A4 quality stainless steel; M12 thread; length 300 Perforated sleeve for secure anchorage in perforated brick; centres the threaded rod; optimised grid structure for effective distribution of the injection mortar in the construction material; diameter 20 and length 85 Static mixer extension for deep drill holes Handling & installation Drill through heat installation 1. Drill 6. Fill with injection mortar 2. Measure out and shorten if necessary 7. Insert threaded rod 3. Drill completely 8. Allow the mortar to cure 4. Clean thoroughly 9. Seal with Aqua-Stop 5. Insert perforated sleeve 10. Secure the object to be mounted Measure out heat installation Make drill hole in building material and remove layer of plaster if necessary Clean drill hole If necessary, shorten the threaded rod (length = of drill hole + layer of insulation + object to be mounted + 20 ) and screw on the Iso-Spacer In perforated brick, only with perforated sleeve. Place this fully in the drill hole Fill the drill hole in the substrate up to 2/3 full with injection mortar or fill the perforated sleeve fully Insert the threaded rod with pre-installed Iso-Spacer into the drill hole by turning it slightly Allow the injection mortar to cure Screw on the Iso-Spacer until just before the plaster Seal the gap with Aqua-Stop Install the object to be mounted 122

2 Building materials & load bearing values Concrete noncracked Thermo Proof C 20/25 Load bearing values 4 (per fixing point with no marginal influence) Drill hole 3 Anchorage Drill Ø Concrete cracked C 20/ kg* 500 kg* Perforated brick2 Hlz 4; Hlz 6; Hlz kg (60 kg) 1, 2 40 kg (80 kg) 1, kg Sand-lime perforated brick KSL 4; KSL 6; KSL kg (60 kg) 1, 2 40 kg (80 kg) 1, 2 85 kg Hbl light concrete Hbl 2; Hbl 4 30 kg 2 60 kg 2 Hbn concrete Hbn 4 60 kg 2 Sand-lime solid brick KS 12; KS kg kg Clay brick MZ ** 90 ** 90 ** 90 ** 100 (90 )** 100 (85 )** ** 85 ** 85 ** 85 ** 110 (130 )* 110 (130 )* 14 (20 in the plaster) 20 (25 in the plaster) 20 (25 in the plaster) 20 (25 in the plaster) 14 (20 in the plaster) 20 (25 in the plaster) Fastening torque 20 Nm 2 Nm 2 Nm 2 Nm 2 Nm 2 Nm 2 Nm 170 kg 14 (20 in the plaster) The load bearing values take into account the partial safety factors in the approvals as well as a partial safety factor of y = 1.4 for the effect. F 1 Value in brackets applies to the drill holes created by rotary drilling. 2 Not included in approvals. 3 Applies to the drill hole in the construction material. The size of the insulation and the layer of plaster are still to be added. 4 When taking measurements, the complete approval notice Z must be taken into account. * Corresponds to the permitted bearing load of the Iso Spacer. ** With perforated sleeve. Packaging Size / Tightening Art. no. Contents Drive Drill Ø contents torque Thermo Proof Thermo Proof per pack 1x Aqua Stop 80 ml 2x Iso Spacer 2x threaded rods 2x perforated sleeves 1x extension per pack Nm 80 ml SW24 (Concrete/ solid M12 x x x Nm ø drill hole anchorage Max. strength size of Insulation object to be layer mounted tetics 14 1) 70 / / / (Concrete*/ (Concrete*/ (Concrete*/ (Concrete*/ (Concrete*/ solid brick**) solid brick**) solid brick**) solid brick**) solid brick**) 20 1) ** ø 90 ** 85 ** 190 ** tetics 2 ** x Aqua Stop 80 ml 16x Iso Spacer 16x threaded rods 16x perforated sleeves 4x extensions 80 ml SW24 (Concrete/ solid M12 x x x ) 70 / / / (Concrete*/ (Concrete*/ (Concrete*/ (Concrete*/ (Concrete*/ solid brick**) solid brick**) solid brick**) solid brick**) solid brick**) 20 1) ** 90 ** 85 ** 190 ** 2 ** 1 If necessary, remove layer of plaster with Ø 20 drill 2 When taking measurements, the complete approval notice Z must be taken into account. * Used with Liquix Pro 1 ** Used with Liquix Plus 7 Shear forces... at full loads α=2 of a fixing point with no marginal influence Thickness of the non-load bearing layer (insulation & plaster) Shear forces 98 kg 81 kg 68 kg 58 kg 51 kg 46 kg 41 kg 38 kg tetics t fi x L = Length of threaded rod 123

3 Thermo Proof Plus installation system SPECIAL INCLUDED SE AL ANT www. You Tube.com/toxgermany Description & application Heavy duty distance fixing for insulation, clinker and flat roofs A4 stainless steel ensures virtually no energy loss and no thermal bridges Approval for use by the construction supervisory authority for all distance installations Simple and speedy installation For insulation up to 215 Z Ideal complement to Liquix injection mortar (universal approval for installation in cracked and non-cracked concrete as well as in solid brick and perforated brick masonry) Variable 10 series and 12 series threaded rod connection Only permitted distance fixing with M10 thread connection used as standard for French balconies, for instance Up to 250% more power than competitive products Suitable for thick layers of insulation and distance installations up to 220 Aqua-Stop provides effective protection from façade rotting due to damp A4 stainless steel provides secure protection against rust Handling & installation Drill through heat insulation (ø 30 ) Measure out heat installation Make drill hole in building material and remove layer of plaster if necessary Clean drill hole If necessary, shorten the threaded rod (length = of drill hole + layer of insulation + object to be mounted + 20 ) and screw on the Iso Spacer In perforated brick, only with perforated sleeve. Place this fully in the drill hole Fill the drill hole in the substrate up to 2/3 full with injection mortar or fill the perforated sleeve fully Insert the threaded rod with pre-installed Iso-Spacer into the drill hole by turning it slightly Allow the injection mortar to cure Screw on the Iso-Spacer until just before the plaster Seal the gap with Aqua-Stop Install the object to be mounted 1. Drill 6. Insert the perforated sleeve, fill with injection mortar 2. Drill through insulation 7. Insert threaded rod 3. Measure out and shorten if necessary 8. Allow the mortar to cure 4. Drill completely 9. Seal with Aqua-Stop 5. Clean thoroughly 10. Secure the object to be mounted 124

4 Building materials & load bearing values Thermo Proof Plus Concrete C 20/25 cracked & non-cracked Connection M10 Concrete C 20/25 cracked and non-cracked Connection M12 Load bearing values (per fixing point with no marginal influence) 1380 kg 660 kg Drill hole 3 Anchorage Drill Ø Tightening torque Perforated brick1 Hlz 4; Hlz 6; Hlz kg (60 kg) 1, 2 40 kg (80 kg) 1, kg Sand-lime perforated brick KSL 4; KSL 6; KSL kg (60 kg) 1, 2 40 kg (80 kg) 1, 2 85 kg Hbl light concrete Hbl 2; Hbl 4 30 kg 2 60 kg 2 Hbn concrete Hbn 4 60 kg 2 Sand-lime solid brick KS 12; KS kg kg Clay brick Mz 12; Mz kg 2 70 kg ** 90 ** 90 ** 90 ** 100 (90 )** 100 (90 )** ** 85 ** 85 ** 85 ** 100 (85 )** 100 (85 )** 18 (30 in the plaster) 20 (30 in the plaster) 20 (30 in the plaster) 20 (30 in the plaster) 20 (30 in the plaster) 18 (30 in the plaster) 20 Nm 2 Nm 2 Nm 2 Nm 2 Nm 2 Nm 2 Nm 18 (30 in the plaster) The load bearing values take into account the partial safety factors in the approvals as well as a partial safety factor of y = 1.4 for the effect. F 1 Value in brackets applies to the drill holes created by rotary drilling. 3 Applies to the drill hole in the construction material. The size of the insulation and the layer of plaster are still to be added. ** With perforated sleeve. 2 Not included in approvals. Packaging Size / Tightening Art. no. Contents Drive Drill Ø contents torque Thermo Proof Plus per pack 1x Aqua Stop 80 ml 2x Iso Spacer 2x threaded rods A4 2x screws A4 2x screws A4 2x perforated sleeves 1x extension 80 ml - - SW24 M16 x 300 M10x40 SW M12x40 SW 20 x x Nm 20 (Concrete/ solid 2 ø 18 1) (Concrete*/ solid brick**) 20 1) ** drill hole 80 / 125 (Concrete*/ solid brick**) 90 ** anchorage 80 / 125 (Concrete*/ solid brick**) 85 ** Max. strength size of Insulation object to be layer mounted tetics 215 / 180 (Concrete*/ solid brick**) 190 ** 2 (Concrete*/ solid brick**) 2 ** 1 30 in the plaster 2 When taking measurements, the complete approval notice Z must be taken into account. * Used with Liquix Pro 1 ** Used with Liquix Plus 7 Shear forces... on fixing point with no marginal influence Thickness of the non-load bearing layer (insulation & plaster) Thread connection M kg 120 kg 98 kg 83 kg 72 kg 63 kg 56 kg 51 kg 47 kg Thread connection M12 60 kg 60 kg 60 kg 60 kg 60 kg 60 kg 56 kg 51 kg 47 kg with a full load (group fixing) with no marginal influence Thickness of the non-load bearing layer (insulation & plaster) Thread connection M kg 120 kg 120 kg 120 kg 120 kg 120 kg 117 kg 100 kg 93 kg Thread connection M12 60 kg 60 kg 60 kg 60 kg 60 kg 60 kg 60 kg 60 kg 60 kg tetics t fi x L = Length of threaded rod 125

5 Wallix masonry set Liquix Sleeve Stix A4 stainless steel Universal heavy duty fixing set with no expansion pressure Approved by the construction supervisory authority for use in conjunction with injection mortars Liquix Pro 1 and Plus 7 for concrete and porous brick masonry A4 stainless steel ensures no rust and virtually no energy loss or thermal bridges www. You Tube.com/toxgermany Description & application Ideal complement to Liquix injection mortar Made from non-rusting steel, with hexagonal bolt, washer and perforated sleeve 20x85 The Stix anchor rod is included in the approvals for Liquix injection mortar Handling & installation Anchor rod made from stainless A4 steel May be used in dry internal areas, moist areas and external areas including in industrial atmospheres and close to the sea Use perforated sleeve in perforated brick Pre-positioned installation 1. Drill 4. Inject the injection mortar 2. Clean drill hole 5. Screw in the threaded rod 3. Insert the perforated sleeve Result in concrete 126

6 Packaging Contents Size / contents Wallix per pack 2x Stix A4 M12x115 Drive Tightening torque Drill Ø drill hole Nm ø size of anchorage object to be mounted Approval Brunnenstraße 31 (D) Krauchenwies TOX-Dübel-Technik GmbH E Art. no. Building materials & load bearing values WALLIX SW ø 20 INOX A4 P Tinst 2 Nm Art M12/115 ø20/85 2x M12/115 ø20/85 2x Art tfix WALLIX 14* 70* (Concrete) (Concrete) (Concrete) (Concrete) SW x sleeves 20 x 85 - / approval 20 * * Used with Liquix Pro 1 d1 tfix 127

7 Liquix Pro 1 injection mortar 0756 TOX-Dübel-Technik GmbH Brunnenstraße 31 D Krauchenwies 09 ETA-09/0258 ETAG , Option CPD-0276 TVM-STV-K M8 - M TOX-Dübel-Technik GmbH Brunnenstraße 31 D Krauchenwies 13 ETA-13/0047 ETAG 029, use category b,c,w/w 0756-CPD-0533 TVM-STV-K M8 - M12 Liquix Mix Liquix Sleeve Liquix Pro ml A single solution or everything: Approved by the construction supervisory authority for cracked and non-cracked concrete, perforated brick and solid brick LEED and emissions tested: for ecological and healthy living Standard threaded rods* may be used Earthquake tested Can be used even at extremely low temperatures (down to -10 C) Can be used in wet and water-logged drill holes Low axis and edge distance due to anchorage with no expansion pressure Secures heavy loads up to 13.8 tonnes in weight Can also be used above the head Fire resistance class F120 Opened cartridges can be re-used by changing the static mixer Variable anchorage saves time and materials * in accordance with approval www. You Tube.com/toxgermany Description & application Liquix Pro 1 is a styrene-free vinyl ester injection mortar available in various cartridge types and cartridge sizes with a Liquix Mix static mixer For fixings subject to approval in cracked and noncracked concrete and masonry Handling & installation A perforated sleeve should be used when working in perforated brick Cleaning of the drill holes Screw the static mixer securely to the cartridge If the insertion deviates from the standard, mark this on the anchor rod Discard approximately the first 10 cm of the injection mortar and do not use it for fixing Starting at the bottom of the drill hole, fill the cleaned drill hole approximately up to 2/3 with injection mortar, or completely full if using a perforated sleeve Insert the anchor rod by turning it slightly until the defined insertion is reached Note the torque and curing time specified under each applicable approval The mortar can be used in dry or moist concrete as well as in water-filled drill holes The Liquix Blaster and Liquix Blaster Pro dispenser guns should be used when working with coaxial, peeler and blown film cartridges; for side-by-side cartridges, use the Liquix Blaster Plus dispenser gun 1. Drill 4. Screw in the threaded rod 2. Clean drill hole In perforated brick: Insert perforated sleeve 3. Inject the injection mortar Result in concrete Result in perforated brick 128

8 Building materials & load bearing values In concrete C20/25 M8 M10 M12 M16 M20 M24 M27 M30 Effective anchorage Permitted centric tensile load of an individual fixing with no marginal influence Nperm. Non-cracked concrete C20/25 Zinc-plated threaded rod, strength class kg kg kg kg kg kg kg kg Threaded rod A4, strength class 50 M kg kg kg kg kg kg kg kg Permitted shear force on a single fixing with no marginal influence Vperm. Zinc-plated threaded rod, strength class kg 860 kg 1200 kg 2230 kg 3490 kg kg kg kg Threaded rod A4, strength class 50 M kg 920 kg 1370 kg 2520 kg 3940 kg kg 3450 kg 4200 kg cracked concrete C20/25 Permitted centric tensile load of an individual fixing with no marginal influence Nperm. Zinc-plated threaded rod, strength class kg kg kg kg kg kg Threaded rod A4, strength class 50 M kg kg kg kg kg kg Permitted shear force on a single fixing with no marginal influence Vperm. Zinc-plated threaded rod, strength class kg 2230 kg kg kg kg kg Threaded rod A4, strength class 50 M kg kg kg kg 3450 kg 4200 kg When taking measurements, the complete ETA 09/0258 approval document must be taken into account The loads indicated relate to anchoring individual fixings in dry and damp concrete and anchoring at temperatures between -40 C up to +24 C (and up to +40 C for short periods) The partial safety factors for resistance regulated in the approval and a partial safety factor of yf = 1.4 are taken into account 1 The anchorage may be freely selected between the values min and max. Packaging Art. no. Type Contents Cartridge Drill Ø drill hole insertion Size of object to be mounted Approval Liquix Pro 1 styrene-free per pack ø ml 1x Liquix Pro 1 2x Liquix Mix 4x Liquix Sleeve coaxial ml 1x Liquix Pro 1 2x Liquix Mix 4x Liquix Sleeve peeler Liquix Pro 1 styrene-free per pack ø ml 12x Liquix Pro 1 24x Liquix Mix peeler ml 12x Liquix Pro 1 24x Liquix Mix side-by-side d1 129

9 Liquix Plus 7 injection mortar 0756 TOX-Dübel-Technik GmbH Brunnenstraße 31 D Krauchenwies 13 ETA-13/0053 ETAG 029, use category b,c,w/w 0756-CPD-0536 TVM-PSF M8 - M TOX-Dübel-Technik GmbH Brunnenstraße 31 D Krauchenwies 13 ETA-13/0052 ETAG , Option CPD-0535 TVM-PSF M8 - M24 Liquix Plus ml www. You Tube.com/toxgermany Liquix Mix Description & application Liquix Sleeve Cost-effective alternative to standard heavy load applications! Low axis and edge distance due to anchorage with no expansion pressure Standard threaded rods* may be used Styrene-free Can be used even in low temperatures (down to -5 C) Can be used in wet and water-logged drill holes Secures heavy loads up to 3.7 tonnes in weight Opened cartridges can be re-used by changing the static mixer * in accordance with approval The mortar can be processed in dry and wet concrete In the case of above-the-head installation, the threaded rod must be fixed in accordance with the processing time Handling & installation A perforated sleeve should be used when working in perforated brick Cleaning of the drill holes Screw the static mixer securely to the cartridge If the insertion deviates from the standard, mark this on the anchor rod Discard approximately the first 10 cm of the injection mortar and do not use it for fixing Starting at the bottom of the drill hole, fill the cleaned drill hole approximately up to 2/3 with injection mortar, or completely full if using a perforated sleeve Insert the anchor rod by turning it slightly until the defined insertion is reached Note the torque and curing time specified under each applicable approval The mortar can be used in dry concrete The Liquix Blaster and Liquix Blaster Pro dispenser guns should be used when working with coaxial, peeler and blown film cartridges; for side-by-side cartridges, use the Liquix Blaster Plus dispenser gun 1. Drill 4. Screw in the threaded rod 2. Clean drill hole Result in concrete 3. Inject the injection mortar Result in perforated brick 130

10 Building materials & load bearing values In concrete M8 M10 M12 M16 M20 M24 Effective anchorage Permitted centric tensile load Nperm. of an individual fixing with no marginal influence in non-cracked concrete C20/25 Zinc-plated threaded rod, strength class kg 1380 kg 1390 kg 1980 kg 2980 kg 3770 kg Threaded rod A4, strength class kg 1380 kg 1390 kg 1980 kg 2980 kg 3770 kg Permitted shear force on a single fixing with no marginal influence Vperm. Zinc-plated threaded rod, strength class kg 860 kg 1200 kg 2230 kg 3490 kg 5030 kg Threaded rod A4, strength class kg 920 kg 1370 kg 2520 kg 3940 kg 5680 kg Permitted bending moment Mperm. Zinc-plated threaded rod, strength class Nm 21.2 Nm 37.7 Nm 94.8 Nm Nm Nm Threaded rod A4, strength class Nm 23.8 Nm Nm Nm Nm Nm Component dimensions and installation figures minimum axis distance smin minimum edge distance cmin Minimum component thickness hmin Drill hole diameter Drill hole Clearance hole to the component to be attached df Torque when anchoring Tinst 10 Nm 20 Nm 40 Nm 60 Nm 120 Nm 150 Nm The loads indicated relate to anchoring individual fixings in dry and damp concrete and anchoring at temperatures between -40 C and +24 C (or for a short period up to +40 C) When taking measurements, the complete declaration of performance 0756-CPD-0535 must be taken into account The partial safety factors for resistance regulated in the approval and a partial safety factor of γ F = 1.4 are taken into account Approved fixings must be used for mountings where safety is a factor (see also fixing 1x1) The technical instructions for working in masonry using perforated sleeves can be found on page 131 Packaging Art. no. Type Contents Cartridge Drill Ø drill hole insertion Size of object to be mounted Approval Liquix Plus 7 styrene-free per pack ø 1x Liquix Plus ml 2x Liquix Mix 6x Liquix Sleeve tubular film x Stix Liquix Plus 7 styrene-free per pack ø ml 12x Liquix Plus 7 24x Liquix Mix coaxial ml 12x Liquix Plus 7 24x Liquix Mix tubular film ml 12x Liquix Plus 7 24x Liquix Mix side-by-side d1 131

11 2C repair adhesive Liquix SOS NEW PRODUCT Static mixer Sieve sleeve Suitable for many construction materials, e.g. concrete, wood, tiles, natural stone Also suitable for insulation materials, such as EPS or PUR Repairing compound for wood perfect for pulled out bore holes Optimal for renovations Can be sanded and painted over Gluing in fixings and anchor rods Bridge gaps up to 10 Quick hardening after 5 min. at 23 C Can also be used as body filler Highest stability Liquix SOS Packaging Order no. Type Content Cartridge min. Depth of bore hole min. Anchoring max. Strength Insulation layer Strength attachment part Approval Liquix SOS per package ø tfix ETA 1x Liquix SOS 25ml ml 4x Sieve sleeve x Static mixer

12 Materials & Retaining values Description & Area of application For fastening of light shelves, curtain rods, towel holders, etc. For repairing pulled out hinges, bore holes that are too large, wooden doors, etc. Temperature resistant from -20 C to +60 C after hardening Fast reacting 2-component repair adhesive with very high strength Can bridge gaps of up to 10 and after hardening it can be grinded and painted Quick hardening guarantees quick post-processing (5 min. at 23 C) Ideal handling at 23 C cartridge temperature Suitable for interior and exterior use Overhead installation Handling & Installation For fastening: Clean bore hole For perforated construction material, board material and perforated bricks, always use sieve sleeve Remove cap and attach static mixer Do not use the first 5 cm of the adhesive for fastening Fill bore hole entirely with repair adhesive Approx. 5 minutes after filling the bore hole, screw the screw into the hardened material The contents of the cartridge (25 ml) are sufficient for at least 4 bore holes (with 10 diameter and 50 ) The mostly expansion pressure free anchoring prevents damaging of tiles and plastering For repair: Pulled out fittings, hinges or wooden pieces just fill it up with Liquix SOS After hardening, remove protruding mass with a suitable tool (e.g. knife and drill) and sand over 1. Clean bore hole 2. Fill bore hole 3. Let it harden 4. Fix object

13 Contact chemical anchor 1109 TOX-Dübel-Technik GmbH Brunnenstraße 31 D Krauchenwies 10 ETA-09/0077 ETAG , Option CPD-0048 TVA M8 - M24 Fast, non-complicated use due to precisely defined volume per drill hole High loads with a small drill diameter Approved by the construction supervisory authority Anchorage with no expansion pressure Small anchorage enables speedy installation Water-tight fixing www. You Tube.com/toxgermany Description & application Glass cartridge chemical anchor with separate components For use in combination with threaded rod TGS ETA approval option 8 For fixing steel constructions, railings, high racks, based plates, columns and wooden constructions with no expansion pressure Handling & installation Clean drill hole Insert the mortar cartridge into the drill hole Slowly turn the threaded rod with a drill so that it vibrates and any excess mortar is visible The prescribed torque and curing time must be observed 1. Drill 4. Screw in the threaded rod Further technical details can be found in performance statement 1109-BPR-0048 Pre-positioned installation 2. Clean drill hole 5. STOP turning if mortar overflows 3. Insert cartridge 6. Screw on the object to be mounted 132

14 Building materials & load bearing values Contact M8 M10 M12 M16 M20 M24 Effective anchorage Permitted centric tensile load of an individual fixing with no marginal influence Nperm. Non-cracked concrete C20/ kg 1200 kg 1600 kg 2000 kg 3000 kg 3600 kg Permitted shear force on a single fixing with no marginal influence Vperm. Zinc-plated, strength class kg 800 kg 1200 kg 2230 kg 3500 kg 5300 kg A4, strength class kg 910 kg 1320 kg 2520 kg 3900 kg 5600 kg Permitted bending moment Zinc-plated, strength class Nm 21.1 Nm 37.1 Nm 94.9 Nm Nm Nm A4, strength class Nm 23.8 Nm 42.1 Nm 106 Nm 207 Nm 359 Nm Component dimensions and installation figures minimum axis distance smin minimum edge distance cmin Minimum component thickness hmin Drill hole diameter Drill hole Clearance hole to the component to be attached df Torque when anchoring Tinst 10 Nm 20 Nm 40 Nm 80 Nm 120 Nm 180 Nm When taking measurements, the complete declaration of performance 1109-BPR-0048 must be taken into account The partial safety factors for resistance regulated in the approval and a partial safety factor of yf = 1.4 are taken into account Approved fixings must be used for mountings where safety is a factor (see also fixing 1x1) Packaging Art. no. Type Fixing contents Screw contents Cartridge Ø Cartridge length Screw size Drill Ø drill hole insertion Size of object to be mounted Approval Contact per pack per pack M8 10x M10 10x M12 10x M16 10x M20 6x M24 6x - ø 9 80 M M M M M M24 / d1 ø 10 / / / / / / d1 133

15 Stix threaded rod Stix Approved for use with Contact chemical anchor and Liquix injection mortar 0756 TOX-Dübel-Technik GmbH Brunnenstraße 31 D Krauchenwies 09 ETA-09/0258 ETAG , Option CPD TOX-Dübel-Technik GmbH Brunnenstraße 31 D Krauchenwies 10 ETA-09/0077 ETAG , Option CPD-0048 Stix Tool Made from A4 rust-free stainless steel... or in cost-effective zinc-plated versions TVM-STV-K M8 - M30 TVA M8 - M TOX-Dübel-Technik GmbH Brunnenstraße 31 D Krauchenwies 13 ETA-13/0047 ETAG 029, use category b,c,w/w 0756-CPD-0533 TVM-STV-K M8 - M TOX-Dübel-Technik GmbH Brunnenstraße 31 D Krauchenwies 13 ETA-13/0053 ETAG 029, use category b,c,w/w 0756-CPD-0536 TVM-PSF M8 - M TOX-Dübel-Technik GmbH Brunnenstraße 31 D Krauchenwies 13 ETA-13/0052 ETAG , Option CPD-0535 TVM-PSF M8 - M24 www. Steel galvanised and zinc-plated anchor rod for use in dry rooms only Anchor rod make from non-rusting A4 steel may be used in dry internal areas, moist areas and external areas including in industrial atmospheres and close to the sea Pre-positioned installation You Tube.com/toxgermany Handling & installation Used with Liquix 1. Drill 1. Drill 2. Clean drill hole 2. Clean drill hole Used with Contact 3. Inject the injection mortar 3. Insert cartridge 4. Screw in the threaded rod 4. Screw in the threaded rod Result in concrete 5. STOP turning if mortar overflows 6. Screw on the object to be mounted 134

16 M8/ Art Building materials Description & application Made from galvanised zinc-plated steel (Stix-VZ) or nonrusting steel (Stix-A4) with external hexagonal drive, insertion marking, rooftop-shaped tip, hexagonal bolt, washer and setting tool The Stix anchor rod is included in the approvals for the Contact chemical anchor and Liquix Pro 1 and Liquix Plus 7 injection mortars For use with chemical anchor and injection mortar Packaging Art. no. Type TGS contents TGS-S contents Thread Ø TGS length Width across Drill Ø drill hole insertion Size of object to be mounted Approval Stix-A4 per pack per pack M8x110 10x 1x M10x130 10x 1x M12x160 10x 1x M16x190 10x 1x Stix-VZ per pack per pack M8x110 10x 1x 1 2 M8 110 SW13/SW5 M SW16/SW7 M SW19/SW8 M SW24/SW M8 110 SW13/SW5 / d1 ø 10 / 9 60 (105) 60 (80) 36 (16) 12 / (105) 60 (90) 55 (25) 14 / / / d1 ø 10 / 9 60 (105) 60 (80) 36 (16) M10x130 10x 1x M SW16/SW7 12 / (105) 60 (90) 55 (25) M10x165 10x 1x M SW16/SW7 12 / (105) 60 (90) 90 (60) M12x160 10x 1x M SW19/SW8 14 / M12x250 10x 1x M SW19/SW8 14 / M16x165 10x 1x M SW24/SW12 18 / M16x190 10x 1x M SW24/SW12 18 / M16x250 10x 1x M SW24/SW12 18 / M20x220 6x 1x M SW30/SW12 24 / M20x260 6x 1x M SW30/SW12 24 / M24x300 6x 1x M SW36/SW13 28 / Stix Stix-VZ per pack per pack 1 2 / d1 ø M8x110 8x 1x M10x130 6x 1x M10x165 4x 1x M8 110 SW13/SW5 M SW17/SW7 M SW17/SW7 10 / 9 60 (105) 60 (80) 36 (16) 12 / (105) 60 (90) 55 (25) 12 / (105) 60 (90) 90 (60) () Masonry work d1 sw1 sw2 135

17 Liquix Sleeve perforated sleeve Liquix Sleeve Plus Liquix Sleeve Pro Liquix Sleeve Is included in approvals for Liquix Automatic centring of the anchor rod as dictated by the construction Liquix Sleeve Plus: Optimum grid structure to reduce mortar usage and optimise fit Liquix Sleeve Pro: For bridging of non-load bearing layers www. You Tube.com/toxgermany Description & application Perforated sleeves specially for use with TOX injection mortars The perforated sleeves are used in masonry in conjunction with the Liquix injection systems Liquix Sleeve and Liquix Sleeve Plus perforated sleeves are included in the approvals for the injection mortar The Liquix Sleeve Pro perforated sleeve is used to bridge nonload carrying layers or achieve high anchorage s Handling & installation Perforated sleeves are not required in solid construction materials 1. Drill 4. Inject the injection mortar Perforated sleeves must be used when working in perforated brick and cavity blocks 2. Clean drill hole 5. Screw in the threaded rod 3. Insert perforated sleeve Result in perforated brick 136

18 D TVM-Z-SHK ø 16/ 85 ø 16 M10 system LIQUIX tvm system LIQUIX tvm TVM-Z-SHK ø 16/ 85 8x Art Building materials & load bearing values Load bearing values in masonry when used with Liquix Pro 1 and Liquix Plus 7 Liquix Sleeve Plus Used with Liquix Pro 1 Threaded rod M8 Perforated sleeve 13x100 Liquix Sleeve Plus Used with Liquix Pro 1 Threaded rod M10 Perforated sleeve 15x100 Liquix Sleeve Used with Liquix Pro 7 M6 M8 M10 M12 Perforated brick HLZ 4 30 kg 30 kg 30 kg 30 kg 30 kg 30 kg HLZ 6 40 kg 40 kg 40 kg 40 kg 40 kg 40 kg HLZ kg 80 kg 70 kg 80 kg 80 kg 80 kg Sand-lime perforated brick KSL 4 30 kg 30 kg 30 kg 30 kg 30 kg 30 kg KSL 6 40 kg 40 kg 40 kg 40 kg 40 kg 40 kg KSL kg 80 kg 70 kg 80 kg 80 kg 80 kg Sand-lime solid brick KS kg 170 kg 50 kg 170 kg 170 kg 170 kg Clay brick Mz kg 170 kg 50 kg 170 kg 170 kg 170 kg Hollow block light concrete HBL kg 30 kg 30 kg 30 kg HBL kg 60 kg 60 kg 60 kg Hollow block concrete Hbn kg 60 kg 60 kg 60 kg Porous concrete PP2 40 kg 40 kg PP4 80 kg 80 kg PP6 160 kg 160 kg Installation data recoended cleaning brush Brush Light {Brush M10} Brush Light {Brush M12} Brush Brush Brush Brush with perforated Anchorage of anchor rod sleeve 80 { - } 90 { - } without perforated sleeve 80 {100 } 90 {100 } Drill hole with perforated sleeve 105 { - } 105 { - } without perforated sleeve 85 {100 } 85 {100 } Drill diameter with perforated sleeve without perforated sleeve Clearance hole in the component to be attached Installation torque Tinst 2 Nm 2 Nm 2 Nm 2 Nm 2 Nm 2 Nm When taking measurements, the relevant complete approval notice must be taken into account. d1 Anchoring is also possible in solid brick without a perforated sleeve For optimum hold strength, the following drill hole cleaning is required as a minimum: 2x blasting, 2x brushing, 2x blasting { } Porous concrete Packaging Art. no. Type Fixing contents Screw contents Perforated sleeve Ø Perforated sleeve length Drill Ø Thread rod drill hole insertion Size of object to be mounted Approval Liquix Sleeve Plus per pack per pack x100 20x x100 20x / d1 ø Stix ø 14 / 10 M / 12 M Liquix Sleeve per pack per pack x50 20x x80 20x x85 20x x130 20x x85 20x / d1 ø Stix ø 12 / 7-9 M6-M / 9 M / 9-12 M / 9-12 M / M12-M x Art TOX-Dübel-Technik GmbH D Krauchenwies Liquix Sleeve per pack per pack / d1 ø Stix ø Sleeve 8x / 12 M Liquix Sleeve Pro per pack per pack / d1 ø Stix ø Sleeve Pro 1x / 7-10 M6-M Sleeve Pro 1x / M10-M Sleeve Pro 1x / M12-M

19 Liquix injection mortar accessories Liquix Longa Liquix Impact www. You Tube.com/toxgermany Liquix Mix Special Liquix Impact: Designed for standard metric screws The component to be attached can be released and attached without releasing the fixing Special Liquix Mix: Approved by the construction supervisory authority For optimum mixing of TOX injection mortar Special Liquix Longa: Simple extension for the static mixer For filling deep drill holes Description & application The Liquix Impact internal thread anchor is designed for standard metric screws and threaded rods in sizes M8 and M10 Liquix Impact Following removal of the object to be mounted, the internal thread anchor is flush with the wall Liquix Impact: For use with injection mortar Liquix Mix static mixer is included in the approvals by the construction supervisory authority for injection mortar Liquix Mix for use with new or opened TVM cartridges Liquix Mix: The static mixer is needed for use with injection mortar. The two components in the cartridge are mixed in the static mixer, which serves to 'activates' them Liquix Mix: Included in the following approvals: General approvals by the construction supervisory authority Z and Z as well as in European Technical Approval ETA 09/0258, ETA , ETA , ETA

20 TVM-Z-SM 200 4x Art system LIQUIX tvm Art no Building materials Packaging Art. no. Type Fixing contents Screw contents Ø length Drill Ø Perforated sleeve drill hole insertion Size of object to be mounted Approval LIQUIX TVM-IGA M10x80 10x Liquix Impact per pack per pack Sleeve / / df ø SHK ø M8x80 10x / 14 / 9 15x M10x80 10x / 16 / 12 20x Liquix Mix per pack per pack / df ø ø Mix 25x Liquix Mix per pack per pack / df ø ø Mix 4x Liquix Longa per pack per pack / df ø ø Longa 10x d1 139

21 Liquix Blaster dispenser gun Liquix Blaster Liquix Blaster Pro Liquix Blaster Plus Little effort and speedy processing regardless of the outside temperature Especially for using injection mortar cartridges thanks to a conversion ratio of 1:17 Ergonomic, anti-slip handle Stable metal design Special Liquix Blaster: Cost-effective alternative to professional models under normal requirements Conversion ratio of up to 1:20 www. You Tube.com/toxgermany Description & application Liquix Blaster: Feed rod guidance: The plastic in the core guarantees smooth gliding Feeder: Two thin metal layers with a plastic interlayer for problem-free dosing of the injection mortar Riveted frame: Robust enough to meet normal demands For the use of injection mortar with coaxial cartridges. Liquix Blaster Pro / Plus: Feed rod guidance: The metal core guarantees precise gliding throughout the entire life cycle due to low wear and tear Feeder: Patented and mass-produced single sheet metal plate made from special alloy; allows precise dosing of the injection mortar Riveted frame: Optimal robustness to meet the professional demands of day-to-day use over the long term Liquix Blaster Pro: For the use of injection mortar with coaxial cartridges. Liquix Blaster Plus: For the use of injection mortar with side-by-side cartridges. Handling & installation The temperature in the anchoring base and the processing and curing times must be noted. Details can be found on the cartridge label Use in concrete: Use in perforated brick: The first 10 cm of every container should be discarded and not used for anchoring 140

22 Building materials Packaging Art. no. Suitable for Contents Ø length Drill Ø Injection mortar drill hole insertion Size of object to be mounted Approval Liquix Blaster per pack ø Liquix Pro 1 / Plus ml coaxial 280 ml peeler 300 ml tubular film 1x ml 280 ml 300 ml Liquix Blaster Pro per pack ø Liquix Pro 1 / Plus ml coaxial 280 ml peeler 300 ml tubular film 1x ml 280 ml 300 ml Liquix Blaster Plus per pack ml side-by-side 1x ø Liquix Pro 1 / Plus ml

23 Brush NEW PRODUCT Brush Tool Brush XL Brush Light Brush Plastic grip Brush T-Grip For optimum retaining values Its use is prescribed in many approvals by the building authority Ergonomic plastic handle Long-lasting and dimensionally stable brush material Special Brush: The cleaning brush for a thorough cleaning of concrete and full brick Special Brush Light: Cleaning brush from nylon suitable for breakable construction material such as perforated brick Special Brush Tool: Bore attachment / adapter for machine cleaning Special Brush XL: Brush extension for cleaning deep bore holes Packaging Order no. Type Content Ø Length Drill Ø Liquix min. Depth of bore hole min. setting Strength attachment part Approval Brush (For concrete and full per package per package M8 1x 1x M10 1x 1x M12 1x 1x M16 1x 1x ø Liquix tfix ETA Brush and Brush Light (for hollow and perforated per package per package M8 - M10 1x 1x M12+M16 1x 1x ø Liquix tfix ETA Brush Tool per package ø Liquix tfix ETA x M Brush XL per package ø Liquix tfix ETA x M Handling & Installation Exact cleaning processes, according to approval, e.g. Liquix or Contact All components with M6 connection thread Use in concrete Use in perforated brick

24 Air blower Taifun Taifun For optimum retaining values Its use is prescribed in many approvals by the building authority Ergonomic handle Flexible plunger, turnable by 360 Suitable for all construction materials www. You Tube.com/toxgermany Packaging Order no. Type Content Ø Length Drill Ø Liquix Taifun per package ml 1x ml 1x ø ø Length Liquix min. Depth of bore hole min. setting Strength attachment part tfix Approval ETA Handling & Installation Blow out bore hole from the inside of the hole Optimum results in combination with the cleaning Brush Use in concrete