PROJECT TITLE PAGE ORANGEWALLstudios

Transcription

1 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 DOCUMENT PROJECT TITLE PAGE PROJECT MANUAL VOLUME 1 Project: Fred Wahl Marine Boat Shop Client: Jim Zimmer Fred Wahl Marine, Inc. 135 Shipyard Way, Reedsport, Oregon Phone: Web Site: Owner s Representative: Dave Morris, SE McGee Engineering, Inc NW Buchanan Avenue, Corvallis, Oregon PO Box 1067, Corvallis, Oregon Phone: Web Site: Civil and Structural Engineer: Dave Morris, SE McGee Engineering, Inc NW Buchanan Avenue, Corvallis, Oregon PO Box 1067, Corvallis, Oregon Phone: Web Site: Mechanical and Electrical Engineer: Fred Shaub, PE Environmental & Engineering Services, Inc. 917 NW Grant Avenue, Corvallis, Oregon Phone: Web Site: Specification Consultant Orangewall Studios 240 N Broadway #308 Portland, OR Phone: Joseph Readdy Issued: 17 April 2017 Copyright 2017 ORANGEWALLstudios. All rights reserved. END OF DOCUMENT PROJECT TITLE PAGE ORANGEWALLstudios

2 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 DOCUMENT TABLE OF CONTENTS PROJECT MANUAL VOLUME 1 Construction Documents Review Set - Not for Construction DIVISION 00 Procurement and Contracting Requirements Introductory Information Project Title Page Table of Contents List of Drawing Sheets Procurement Requirements Instructions to Bidders Geotechnical Data Preliminary Schedules Bid Form (Single-Prime Contract) Health and Safety Requirements Wage Rate Requirements DIVISION 01 General Requirements Summary Summary General Requirements Price and Payment Procedures Alternates Substitution Procedures Contract Modification Procedures Payment Procedures Owner-furnished Products Submittal Procedures DIVISION 02 Existing Conditions (Not used) DIVISION 03 Concrete Concrete Cast-in-place Concrete Concrete Formwork Concrete Anchors Concrete Reinforcement Division 04 Masonry (not used) DIVISION 05 Metals Metals Structural Steel Steel Joist Framing Steel Decking Cold-formed Metal Framing Metal Fabrications, Metal Pan Stairs and Railings TABLE OF CONTENTS ORANGEWALLstudios

3 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 Division 06 Woods, Plastics, and Composites (Not used) Division 07 Thermal and Moisture Protection Insulation Thermal Insulation Metal Standing-seam Metal Roof Panels Formed Metal Wall Panels Sheet Metal Flashing and Trim Division 08 Openings Hollow Metal Doors and Frames Overhead Coiling Doors Stainless Steel Windows Door Hardware Division 09 Finishes Gypsum Board Resilient Base and Accessories Interior Painting Division 10 Specialties Toilet, Bath, and Laundry Accessories Division 11 Equipment (Not used) Division 12 Furnishings (Not used) Division 13 Special Construction (Not used) Division 14 Conveying Equipment (Not used) Division 21 Fire Suppression Fire Suppression Automatic Sprinkler System Division 22 Plumbing Plumbing Materials & Methods Plumbing Specialties Plumbing Domestic Division 23 Heating, Ventilating, and Air Conditioning Mechanical Materials & Methods Heating, Ventilating, and Air-conditioning Fuel Piping TABLE OF CONTENTS ORANGEWALLstudios

4 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 Division 26 Electrical Electrical Materials, Methods, & Basic Requirements Conductors & Cables Raceways & Boxes Vibration & Seismic Control for Electrical Systems Identification for Electrical Systems Switchboards Panelboards Panel Distribution Units Wiring Devices Low Voltage Circuit Protective Devices Enclosed Switches & Circuit Breakers Lighting Control Devices Lighting Division 31 Earthwork Earthwork Driven Pipe Pilings Division 32 Exterior Improvements Asphalt Paving Division 33 Utilities Site Water Site Sanitary Sewer Site Storm Drainage APPENDIX A Geotechnical Report by Foundation Engineering. Copyright 2017 ORANGEWALLstudios. All rights reserved. END OF DOCUMENT TABLE OF CONTENTS ORANGEWALLstudios

5 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 DOCUMENT LIST OF DRAWING SHEETS 1.1 LIST OF DRAWINGS A. Drawings: Drawings consist of the Contract Drawings and other drawings listed on the Table of Contents page of the separately bound drawing set titled Fred Wahl Marine Boat Shop, dated 17 April 2017 as modified by subsequent Addenda and Contract modifications. B. List of Drawings: Drawings consist of the following Contract Drawings and other drawings of type indicated: Cover Sheet; Site Plan; General Notes; Project Directory; Index to the Drawings 0.0 Cover Sheet C1.1 Site Civil/ Existing Conditions C1.2 Site Grading Plan C1.3 Site Utility Plan C2.1 Site Work Details 1.0 Overall Site Plan 1.1 First Floor Plan 1.2 Second Floor Plan 1.3 Main Stairs and Restrooms 1.4 Main Stair Details 1.5 Secondary Stairs 1.6 Roof Plan Restroom Plan 2.1 Building Elevations 2.2 Building Section 2.3 Siding and Roofing Details S1.0 Specifications and Design Loads S1.1 Foundation Plan S1.2 Floor Framing Plan S1.3 Lower Roof Framing Plan S1.4 Crane Level Framing Plan S1.5 Upper Roof Framing Plan LIST OF DRAWING SHEETS ORANGEWALLstudios

6 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 S2.1 Section at Braced Frames S2.2 Section at Unbraced Frames S2.3 Longitudinal Section S2.4 Structural Elevation Side Walls S2.5 South End Wall S2.6 North End Wall S2.7 North Door Details S2.8 South Door Details S2.9 Roof Truss Details S3.1 Foundation Details S3.2 Steel Connections S3.3 Floor Framing Details S3.4 Roof Framing Details S3.5 Braced Frame Details S3.6 Steel Connections MP1.0 Mechanical/ Plumbing/ Utilities Site Plan FS-1.1 First Floor Fire Sprinkler Plan FS-1.2 Second Floor Fire Sprinkler Plan FS-2.1 Fire Sprinkler Section MP 1.0 Mechanical/Plumbing Site Plan M1.1 HVAC Plan M6.1 Mechanical Equipment List P1.1 Plumbing Plan 31.0 Electrical Site Plan E1.1 Power Plan E1.2 Lighting Plan E2.1 Lighting Section E3.1 Lighting Section LIST OF DRAWING SHEETS ORANGEWALLstudios

7 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 E6.1 One Line and Schedules E6.2 Panel Schedules E6.3 Panel Schedules END OF DOCUMENT LIST OF DRAWING SHEETS ORANGEWALLstudios

8 Wahl Marine Boat Procurement and Contracting Requirements 17 April INVITATION TO BID 1.1 PROJECT INFORMATION A. Notice to Bidders: Selected bidders are invited to submit bids for Project as described in this Document according to the Instructions to Bidders. B. Project Identification: Fred Wahl Marine Boat Shop Owner: Fred Wahl Marine, Inc. Address: 135 Shipyard Way, Reedsport, Oregon Phone: Web Site: Owner's Representative: Dave Morris, SE C. Civil and Structural Engineer: McGee Engineering, Inc. Address: 8040 NW Buchanan Avenue, Oregon Phone: Web Site: Project Manager: Dave Morris, SE D. Project Description: Project consists of Bid Package A, to be bid separately, that includes excavation and furnishing and driving of pilings; and Bid Package B that includes all other work as described on plans. See Section for a more detailed description. 1. Bid includes a deductive alternate for the design and construction of the structural steel frame, insulated steel wall assemblies, and insulated steel roof assemblies. See Section for a more detailed description. E. Construction Contract: Bids will be received for the following Work: 1. Bid Package B - General Contract (all trades). 1.2 BID SUBMITTAL AND OPENING A. Owner will receive sealed bids until the bid time and date at the location indicated below. Owner will consider bids prepared in compliance with the Instructions to Bidders issued by Owner, and delivered as follows: 1. Bid Date: Wednesday 17 May Bid Time: 4:00 pm Pacific Daylight Time. 3. Location: McGee Engineering, Inc., 8040 NW Buchanan Avenue, Oregon B. Bids will be thereafter privately opened. 1.3 BID SECURITY A. Not required. No bids may be withdrawn for a period of 60 days after opening of bids. Owner reserves the right to reject any and all bids and to waive informalities and irregularities. INVITATION TO BID ORANGEWALLstudios

9 Wahl Marine Boat Procurement and Contracting Requirements 17 April 2017 B. PREBID CONFERENCE 1. A prebid conference for all bidders will be held at the jobsite. on Wednesday, 26 April 2017 at 10:00 a.m Pacific Daylight Time. Prospective bidders are requested to attend. 1.4 DOCUMENTS A. Procurement and Contracting Documents: Obtain after 17 April 2017 by contacting McGee Engineering. Documents will be provided in electronic format. Documents will be provided to prime bidders only; only complete sets of documents will be issued. Contractors are responsible for distributing copies to Subcontractors. 1.5 TIME OF COMPLETION A. Bidders shall begin the Work on receipt of the Notice to Proceed and shall complete the Work within the Contract Time: 15 April BIDDER'S QUALIFICATIONS A. Bidders must have been preselected by Owner. B. Bidders must be properly licensed under the laws governing their respective trades and be able to obtain insurance and bonds required for the Work. A Performance Bond, a separate Labor and Material Payment Bond, and Insurance in a form acceptable to Owner will be required of the successful Bidder. 1.7 PREVAILING WAGE A. The project is being partially funded by a grant from the Oregon Department of Transportation and is subject to prevailing wage requirements. END OF DOCUMENT INVITATION TO BID ORANGEWALLstudios

10 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 DOCUMENT INSTRUCTIONS TO BIDDERS 1.1 INSTRUCTIONS TO BIDDERS A. AIA Document A701, "Instructions to Bidders," is hereby incorporated into the Procurement and Contracting Requirements by reference. 1. A copy of AIA Document A701, "Instructions to Bidders," is bound in this Project Manual. END OF DOCUMENT INSTRUCTIONS TO BIDDERS ORANGEWALLstudios

11 Wahl Marine Boat Project Schedule 07 April 2017 DOCUMENT PROJECT SCHEDULE 1.1 PROJECT SCHEDULE A. This Document with its referenced attachments is part of the Procurement and Contracting Requirements for Project. They provide Owner's information for Bidders' convenience and are intended to supplement rather than serve in lieu of Bidders' own investigations. They are made available for Bidders' convenience and information, but do not affect Contract Time requirements. This Document and its attachments are not part of the Contract Documents. B. Milestone Dates: 1. Bid Date: May 17, Anticipated Award Date: June 1, Anticipated date of Building Permit Issuance: June 23, Project Completion Date: April 15, 2018 C. Related Requirements: 1. Document "Bid Form - Stipulated Sum (Single-Prime Contract)" 2. Document "Administrative Requirements" 3. Document Project Management and Coordination for Contractor's construction schedule requirements. END OF DOCUMENT PROJECT SCHEDULE ORANGEWALLstudios

12 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 DOCUMENT GEOTECHNICAL DATA A. GEOTECHNICAL REPORT 1. Bolon Island Boat Shop Geotechnical Report by Foundation Engineering dated April 10, 2017 is included in this project manual and is part of the specification. END OF DOCUMENT HEALTH AND SAFETY REQUIREMENTS ORANGEWALLstudios

13 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 DOCUMENT BID FORM - STIPULATED SUM (SINGLE-PRIME CONTRACT) 1.1 BID INFORMATION A. Bidder:. B. Project Name: Fred Wahl Marine Boat Shop C. Project Location: 135 Shipyard Way, Reedsport, Oregon D. Owner: Fred Wahl Marine E. Engineer: McGee Engineering, Inc. F. Engineer Project Number: CERTIFICATIONS AND BASE BID A. Base Bid, Single-Prime (All Trades) Contract: The undersigned Bidder, having carefully examined the Procurement and Contracting Requirements, Conditions of the Contract, Drawings, Specifications, and all subsequent Addenda, as prepared by McGee Engineering, Inc. and Engineer's consultants, having visited the site, and being familiar with all conditions and requirements of the Work, hereby agrees to furnish all material, labor, equipment and services, including all scheduled allowances, necessary to complete the construction of the above-named project, according to the requirements of the Procurement and Contracting Documents, for the stipulated sum of: 1. Dollars $. 2. The above amount may be modified by amounts indicated by the Bidder on the attached Document "Alternates Form." 1.3 ALTERNATES A. Alternate 1: The undersigned Bidder agrees to provide a deductive alternative to the base bid that includes design, engineering, fabrication, and erection of a structural steel frame as described in Section and compatible with the basis of design shown on the Drawings. Indicate amount to be deducted from contract amount if Alternate is accepted: 1. Dollars (- $ ). B. Alternate 2: The undersigned Bidder agrees to provide an additive alternative to the base bid that includes placing two 50 lengths of crane rails furnished by others and setting the two 70 bridge cranes on the rails. Indicate amount to be added two the contract amount if Alternate is accepted: 2. Dollars ($ ). 1.4 BID GUARANTEE A. The undersigned Bidder agrees to execute a contract for this Work in the above amount and to furnish surety as specified within 10 days after a written Notice of Award, if offered within 60 days after receipt of bids. BID FORM - STIPULATED SUM ORANGEWALLstudios

14 Wahl Marine Boat Procurement and Contracting Documents 17 April SUBCONTRACTORS AND SUPPLIERS A. The following companies shall execute subcontracts for the portions of the Work indicated: 1. Concrete Work:. 2. Masonry Work:. 3. Roofing Work:. 4. Plumbing Work:. 5. HVAC Work:. 6. Electrical Work:. 1.6 TIME OF COMPLETION A. The undersigned Bidder proposes and agrees hereby to commence the Work of the Contract Documents on a date specified in a written Notice to Proceed to be issued by Owner s Representative, and shall fully complete the Work on, or before, 30 April ACKNOWLEDGEMENT OF ADDENDA A. The undersigned Bidder acknowledges receipt of and use of the following Addenda in the preparation of this Bid: 1. Addendum No. 1, dated. 2. Addendum No. 2, dated. 3. Addendum No. 3, dated. 4. Addendum No. 4, dated. 1.8 BID SUPPLEMENTS A. The following supplements are a part of this Bid Form and are attached hereto. 1. Bid Form Supplement - Alternates. 1.9 CONTRACTOR'S LICENSE A. The undersigned further states that it is a duly licensed contractor, for the type of work proposed, in the State of Oregon, the County of Douglas County, and the City of Reedsport, and that all fees, permits, etc., pursuant to submitting this proposal have been paid in full SUBMISSION OF BID A. Respectfully submitted this day of, B. Submitted By: (Name of bidding firm or corporation). C. Authorized Signature: (Handwritten signature). D. Signed By: (Type or print name). BID FORM - STIPULATED SUM ORANGEWALLstudios

15 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 E. Title: (Owner/Partner/President/Vice President). F. Witness By: (Handwritten signature). G. Attest: (Handwritten signature). H. By: (Type or print name). I. Title: (Corporate Secretary or Assistant Secretary). J. Street Address:. K. City, State, Zip:. L. Phone:. M. License No.:. N. Federal ID No.: (Affix Corporate Seal Here). END OF DOCUMENT BID FORM - STIPULATED SUM ORANGEWALLstudios

16 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 DOCUMENT HEALTH AND SAFETY REQUIREMENTS A. HEALTH AND SAFETY REQUIREMENTS 1. The contractor shall at all times conduct work in such a manner as to comply with all Occupational Safety and Health Administration (OSHA) requirements, shall minimize the possibility of accident or injury of any workers or the general public, and shall conduct the work, maintain operations, and provide all reasonable safeguards so as to protect public and private property as well as to protect persons from injury. 2. If in the opinion of the Owner s authorized representative the contractor is in violation of the above safety practices, the Owner s authorized representative may issue and post a stop-work order if the contractor, after being informed of such violation, refuses to comply immediately. The Owner s authorized representative will also notify the OSHA of such action. 3. The Owner s authorized representative s role is not one of supervision or safety management, but of observation only. Nothing contained in this section or elsewhere in this document shall be interpreted to obligate the City to act in any situation, nor shift the applicant s responsibility for safety compliance to the Owner. No responsibility for the safety of the work or for construction means, methods, techniques, sequences, or procedures shall attach to the Owner by virtue of either action or inaction. END OF DOCUMENT HEALTH AND SAFETY REQUIREMENTS ORANGEWALLstudios

17 Wahl Marine Boat Procurement and Contracting Documents 17 April 2017 DOCUMENT WAGE RATE REQUIREMENTS 1.1 WAGE RATE REQUIREMENTS A. The Contractor is solely responsible to determine the applicable wage rates and to be in compliance. 1. ORS 279C.800 et seq., to ensure that contractors compete on their ability to perform work competently and efficiently while maintaining community established compensation standards, to encourage the training and education of workers in industry skill standards and to encourage employers to use the funds required by the PWR law for fringe benefits for the actual purchase of such benefits. ORS 279C The Bureau of Labor and Industries (BOLI) is responsible for administering and enforcing the PWR law and for educating contractors, subcontractors and public agencies about its requirements. B. This guide focuses on PWR requirements and BOLI enforcement. Underpaid employees as well as contractors, subcontractors, or other interested parties may file complaints with BOLI s Wage and Hour Division, or file a civil suit for damages against a violator of the PWR law. END OF DOCUMENT WAGE RATE REQUIREMENTS ORANGEWALLstudios

18 Wahl Marine Boat General Requirements 17 April 2017 SECTION SUMMARY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Project information. 2. Work Covered by Contract Documents. 3. Work Under Separate Contracts. 4. Owner-furnished Products. 5. Access to site. 6. Coordination with Occupants. 7. Work Restrictions 8. Specification and Drawing conventions. B. Related Requirements: 1. Section "Temporary Facilities and Controls" for limitations and procedures governing temporary use of Owner's facilities. 1.3 PROJECT INFORMATION A. Project Identification: Fred Wahl Marine Boat Shop 1. Project Location: 135 Shipyard Way, Reedsport, Oregon B. Owner: Fred Wahl Marine, 135 Shipyard Way, Reedsport, Oregon Owner's Representative: Dave Morris McGee Engineering, Inc NW Buchanan Avenue, Corvallis, Oregon Phone: Dave Morris <davemorris@mcgee-engineering.com> 1.4 WORK COVERED BY CONTRACT DOCUMENTS A. The Work of Project as defined by the Contract Documents consists of all work required to construct a 155 x 200 steel frame building with two 41 x200 concrete floors. For the purposes of Contracting the work is broken up into two packages. 1. Package A: Excavation and Pile Driving. This package includes excavating the building pad to subgrade elevation and furnishing and installing pipe piling. This package does not include pile cutoffs and capping. This work will be handled directly by the Owner and is not offered for bid. SUMMARY ORANGEWALLstudios

19 Wahl Marine Boat General Requirements 17 April Package B: All work not specifically included in Package A included but not limited to: a. Pile cutoffs and connections to foundation b. Placing crushed aggregate base material and backfilling foundations c. Concrete foundations d. Structural steel, steel joists, steel decking and deck concrete. e. Stairs and railings f. Framing for restrooms and mechanical room g. Mechanical and plumbing systems. h. Automatic fire sprinkler system. i. Lighting and Power. j. Secondary wall and roof framing. k. Roofing, siding and building insulation. l. Man doors, coiling doors and windows m. Install Owner furnished items including overhead bridge crane and large doors in North and south end walls. B. Type of Contract: 1. Project will be constructed under a single prime contract for a stipulated price. 2. Permit Fees: a. Owner will directly pay the regulating authority having jurisdiction for the following: b. The Contractor will pay the following permit fees. The Owner will compensate the Contractor as a direct expense at cost upon presentation of invoices: 1) Grading permit, if required. 2) Building permit. 3) Mechanical and plumbing permit, if deferred submittal. 4) Electrical permit, if deferred submittal. 5) Fire sprinkler permit. 1.5 WORK UNDER SEPARATE CONTRACTS A. General: Cooperate fully with separate contractors so work on those contracts may be carried out smoothly, without interfering with or delaying Work under this Contract or other contracts. Coordinate the Work of this Contract with work performed under separate contracts. B. Preceding Work: Owner will award separate contract(s) for the following construction operations at Project site. Those operations are scheduled to be substantially complete before Work under this Contract begins. 1. Package A : Fred Wahl Marine Construction. 1.6 OWNER-FURNISHED PRODUCTS A. Owner will furnish products indicated. The Work includes receiving, unloading, handling, storing, protecting, and installing Owner-furnished products. B. Owner-Furnished Products: 1. Two 70 span 25 ton bridge cranes. Work includes only setting cranes on rail supplied by others. No electrical or mechanical connections are required. SUMMARY ORANGEWALLstudios

20 Wahl Marine Boat General Requirements 17 April wide x 65 tall sliding hangar type doors x50 hinged doors 1.7 ACCESS TO SITE A. General: Contractor shall have limited use of Project site for construction operations as indicated on Drawings by the Contract limits and as indicated by requirements of this Section. B. Use of Site: Limit use of Project site to areas within the Contract limits indicated. Do not disturb portions of Project site beyond areas in which the Work is indicated. 1. Limits: Confine construction operations to the extent indicated on the Construction Documents. 2. Limit site disturbance, including earthwork and clearing of vegetation, to 40 feet (12.2 m) beyond building perimeter; 10 feet (3 m) beyond surface walkways, patios, surface parking, and utilities less than 12 inches (300 mm) in diameter; 15 feet (4.5 m) beyond primary roadway curbs and main utility branch trenches; and 25 feet (7.6 m) beyond constructed areas with permeable surfaces (such as pervious paving areas, stormwater detention facilities, and playing fields) that require additional staging areas in order to limit compaction in the constructed area. 3. Driveways, Walkways and Entrances: Keep driveways, service areas, loading areas, and entrances serving premises clear and available to Owner, Owner's employees, and emergency vehicles at all times. Do not use these areas for parking or for storage of materials. a. Schedule deliveries to minimize use of driveways and entrances by construction operations. b. Schedule deliveries to minimize space and time requirements for storage of materials and equipment on-site. C. Condition of Existing Building: Maintain portions of existing building affected by construction operations in a weathertight condition throughout construction period. Repair damage caused by construction operations. D. Condition of Existing Grounds: Maintain portions of existing grounds, landscaping, and hardscaping affected by construction operations throughout construction period. Repair damage caused by construction operations. 1.8 COORDINATION WITH OCCUPANTS A. Full Owner Occupancy: Owner will occupy a portion of the site and adjacent buildings during the period of construction. Cooperate with Owner during construction operations to minimize conflicts. Perform the Work so as not to interfere with Owner's day-to-day operations. 1.9 WORK RESTRICTIONS A. Work Restrictions, General: Comply with restrictions on construction operations. 1. Comply with limitations on use of public streets and with other requirements of authorities having jurisdiction. B. On-Site Work Hours: Limit work in the existing building to normal business working hours of 8:00 a.m. to 5:00 p.m., Monday through Friday, unless otherwise indicated. For work on the new structure: 1. Weekend Hours: Coordinate with Owner. 2. Early Morning Hours: Comply with Local ordinances. No start before 7:00 a.m. without prior approval of Owner. SUMMARY ORANGEWALLstudios

21 Wahl Marine Boat General Requirements 17 April 2017 C. Existing Utility Interruptions: Do not interrupt utilities serving facilities occupied by Owner or others unless permitted under the following conditions and then only after providing temporary utility services according to requirements indicated: 1. Notify Owner s Representative not less than two days in advance of proposed utility interruptions. 2. Obtain Owner's written permission before proceeding with utility interruptions. D. Noise, Vibration, and Odors: Coordinate construction operations that may result in high levels of noise and vibration, odors, or other disruption to Owner occupancy with Owner. 1. Notify Owner s Representative not less than two days in advance of proposed disruptive operations. 2. Obtain Owner's written permission before proceeding with disruptive operations. 3. Nonsmoking Site: Smoking is not permitted on site. 4. Retain remaining paragraphs to correspond to Owner's requirements. Revise to suit Project. Where Owner's requirements are extensive, see and insert Owner policy and procedure documents in the Project Manual SPECIFICATION AND DRAWING CONVENTIONS A. Specification Content: The Specifications use certain conventions for the style of language and the intended meaning of certain terms, words, and phrases when used in particular situations. These conventions are as follows: 1. Imperative mood and streamlined language are generally used in the Specifications. The words "shall," "shall be," or "shall comply with," depending on the context, are implied where a colon (:) is used within a sentence or phrase. 2. Specification requirements are to be performed by Contractor unless specifically stated otherwise. B. Division 01 General Requirements: Requirements of Sections in Division 01 apply to the Work of all Sections in the Specifications. C. Drawing Coordination: Requirements for materials and products identified on Drawings are described in detail in the Specifications. One or more of the following are used on Drawings to identify materials and products: 1. Terminology: Materials and products are identified by the typical generic terms used in the individual Specifications Sections. 2. Abbreviations: Materials and products are identified by abbreviations published as part of the U.S. National CAD Standard and scheduled on Drawings. 3. Keynoting: Materials and products are identified by reference keynotes referencing Specification Section numbers found in this Project Manual. PART 2 - PRODUCTS (Not Used) PART 3 - EXECUTION (Not Used) END OF SECTION SUMMARY ORANGEWALLstudios

22 Wahl Marine Boat General Requirements 17 April 2017 SECTION ALTERNATES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section includes administrative and procedural requirements for alternates. 1.3 DEFINITIONS A. Alternate: An amount proposed by bidders and stated on the Bid Form for certain work defined in the bidding requirements that may be added to or deducted from the base bid amount if the Owner decides to accept a corresponding change either in the amount of construction to be completed or in the products, materials, equipment, systems, or installation methods described in the Contract Documents. 1. Alternates described in this Section are part of the Work only if enumerated in the Agreement. 2. The cost or credit for each alternate is the net addition to or deduction from the Contract Sum to incorporate alternates into the Work. No other adjustments are made to the Contract Sum. 1.4 PROCEDURES A. Coordination: Revise or adjust affected adjacent work as necessary to completely integrate work of the alternate into Project. 1. Include as part of each alternate, miscellaneous devices, accessory objects, and similar items incidental to or required for a complete installation whether or not indicated as part of alternate. B. Execute accepted alternates under the same conditions as other work of the Contract. C. Schedule: A schedule of alternates is included at the end of this Section. Specification Sections referenced in schedule contain requirements for materials necessary to achieve the work described under each alternate. PART 2 - PRODUCTS (Not Used) PART 3 - EXECUTION 3.1 ALTERNATE 1 A. At the Contractors option a bid may be provided for Alternate No.1. The Contractor is not required to provide a price for this item. ALTERNATES ORANGEWALLstudios

23 Wahl Marine Boat General Requirements 17 April 2017 B. Description of Alternate 1: Provide a design-build, pre-engineered braced steel frame structure with insulated sheet metal wall sheathing with integral vision panels and insulated roof sheathing. 1. Bracing may be Special Concentric Braced frames as shown on the plans or alternate braced system including buckling restrained braced frames. Moment resisting frames are not acceptable. 2. Alternate designs may include alternate girts and purlins provided they are designed to meet the loads required by code and shown on the plans. 3. Alternate designs must include support for the elevated concrete floor slab, stairs and openings. 4. Alternate designs must provide vertical and lateral support for the bridge crane and doors. 5. Alternate floor joists may be proposed provided they meet strength and deflection limits shown on the plans under the loads shown on the plans. 6. Roofing, siding and trim systems must be a complete system resisting the loads required by the plans and the framing the openings shown on the plans. C. For Contractors providing a price for alternate 1 attach supplemental information along with the bid form providing a general description of the proposed alternate structural system. 1. Proposed lateral bracing system. 2. Proposed roofing and siding systems 3. Proposed alternate girt and purlin systems 4. Any other proposed member changes 5. Changes to the foundation which may be required to accommodate the proposed system. D. In the event that Alternate 1 is selected the Contractor shall provide stamped engineering drawings and calculations for any work redesigned due to the alternate. 3.2 ALTERNATE 2 A. Alternate 2: Provide lump sum additional cost to place two 50 lengths of crane rail and set the two 70 bridge cranes on the rails. The cranes are to be secured in place but no electrical or mechanical connections are to be performed by the contractor. END OF SECTION ALTERNATES ORANGEWALLstudios

24 Wahl Marine Boat General Requirements 17 April 2017 SECTION SUBSTITUTION PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section includes administrative and procedural requirements for substitutions. B. Related Requirements: 1. Section "Allowances" for products selected under an allowance. 2. Section "Alternates" for products selected under an alternate. 3. Section "Product Requirements" for requirements for submitting comparable product submittals for products by listed manufacturers. 1.3 DEFINITIONS A. Substitutions: Changes in products, materials, equipment, and methods of construction from those required by the Contract Documents and proposed by Contractor. 1. Substitutions for Cause: Changes proposed by Contractor that are required due to changed Project conditions, such as unavailability of product, regulatory changes, or unavailability of required warranty terms. 2. Substitutions for Convenience: Changes proposed by Contractor or Owner that are not required to meet other Project requirements but may offer advantage to Contractor or Owner. 1.4 ACTION SUBMITTALS A. Substitution Requests: Submit three copies of each request for consideration. Identify product or fabrication or installation method to be replaced. Include Specification Section number and title and Drawing numbers and titles. 1. Substitution Request Form: Use CSI Substitution Request Form or as approved by Owner s Representative. 2. Documentation: Show compliance with requirements for substitutions and the following, as applicable: a. Statement indicating why specified product or fabrication or installation method cannot be provided, if applicable. b. Coordination of information, including a list of changes or revisions needed to other parts of the Work and to construction performed by Owner and separate contractors that will be necessary to accommodate proposed substitution. c. Detailed comparison of significant qualities of proposed substitutions with those of the Work specified. Include annotated copy of applicable Specification Section. Significant qualities may include attributes, such as performance, weight, size, durability, visual effect, sustainable design characteristics, warranties, and specific features and requirements indicated. Indicate deviations, if any, from the Work specified. SUBSTITUTION PROCEDURES ORANGEWALLstudios

25 Wahl Marine Boat General Requirements 17 April 2017 d. Product Data, including drawings and descriptions of products and fabrication and installation procedures. e. Samples, where applicable or requested. f. Certificates and qualification data, where applicable or requested. g. List of similar installations for completed projects, with project names and addresses as well as names and addresses of owners. h. Material test reports from a qualified testing agency, indicating and interpreting test results for compliance with requirements indicated. i. Research reports evidencing compliance with building code in effect for Project. j. Detailed comparison of Contractor's construction schedule using proposed substitutions with products specified for the Work, including effect on the overall Contract Time. If specified product or method of construction cannot be provided within the Contract Time, include letter from manufacturer, on manufacturer's letterhead, stating date of receipt of purchase order, lack of availability, or delays in delivery. k. Cost information, including a proposal of change, if any, in the Contract Sum. l. Contractor's certification that proposed substitution complies with requirements in the Contract Documents, except as indicated in substitution request, is compatible with related materials and is appropriate for applications indicated. m. Contractor's waiver of rights to additional payment or time that may subsequently become necessary because of failure of proposed substitution to produce indicated results. 3. Owner s Representative's Action: If necessary, Owner s Representative will request additional information or documentation for evaluation within three business days of receipt of a request for substitution. Owner s Representative will notify Contractor of acceptance or rejection of proposed substitution within 10 days of receipt of request, or seven days of receipt of additional information or documentation, whichever is later. a. Forms of Acceptance: Change Order, Construction Change Directive, or Owner s Representative's Supplemental Instructions for minor changes in the Work. b. Use product specified if Owner s Representative does not issue a decision on use of a proposed substitution within time allocated. 1.5 QUALITY ASSURANCE A. Compatibility of Substitutions: Investigate and document compatibility of proposed substitution with related products and materials. Engage a qualified testing agency to perform compatibility tests recommended by manufacturers. 1.6 PROCEDURES A. Coordination: Revise or adjust affected work as necessary to integrate work of the approved substitutions. 1.7 SUBSTITUTIONS A. Substitutions for Cause: Submit requests for substitution immediately on discovery of need for change, but not later than 15 days prior to time required for preparation and review of related submittals. 1. Conditions: Owner s Representative will consider Contractor's request for substitution when the following conditions are satisfied. If the following conditions are not satisfied, Owner s Representative will return requests without action, except to record noncompliance with these requirements: a. Requested substitution is consistent with the Contract Documents and will produce indicated results. b. Requested substitution provides sustainable design characteristics that specified product provided for compliance with ASHRAE requirements. SUBSTITUTION PROCEDURES ORANGEWALLstudios

26 Wahl Marine Boat General Requirements 17 April 2017 c. Substitution request is fully documented and properly submitted. d. Requested substitution will not adversely affect Contractor's construction schedule. e. Requested substitution has received necessary approvals of authorities having jurisdiction. f. Requested substitution is compatible with other portions of the Work. g. Requested substitution has been coordinated with other portions of the Work. h. Requested substitution provides specified warranty. i. If requested substitution involves more than one contractor, requested substitution has been coordinated with other portions of the Work, is uniform and consistent, is compatible with other products, and is acceptable to all contractors involved. B. Substitutions for Convenience: Not allowed. PART 2 - PRODUCTS (Not Used) PART 3 - EXECUTION (Not Used) END OF SECTION SUBSTITUTION PROCEDURES ORANGEWALLstudios

27 Wahl Marine Boat General Requirements 17 April 2017 SECTION CONTRACT MODIFICATION PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section includes administrative and procedural requirements for handling and processing Contract modifications. B. Related Requirements: 1. Section "Substitution Procedures" for administrative procedures for handling requests for substitutions made after the Contract award. 1.3 MINOR CHANGES IN THE WORK A. Owner s Representative will issue supplemental instructions authorizing minor changes in the Work, not involving adjustment to the Contract Sum or the Contract Time, on AIA Document G710, included in Project Manual. 1.4 PROPOSAL REQUESTS A. Owner-Initiated Proposal Requests: Owner s Representative will issue a detailed description of proposed changes in the Work that may require adjustment to the Contract Sum or the Contract Time. If necessary, the description will include supplemental or revised Drawings and Specifications. 1. Work Change Proposal Requests issued by Owner s Representative are not instructions either to stop work in progress or to execute the proposed change. 2. Within time specified in Proposal Request or 20 days, when not otherwise specified, after receipt of Proposal Request, submit a quotation estimating cost adjustments to the Contract Sum and the Contract Time necessary to execute the change. a. Include a list of quantities of products required or eliminated and unit costs, with total amount of purchases and credits to be made. If requested, furnish survey data to substantiate quantities. b. Indicate applicable taxes, delivery charges, equipment rental, and amounts of trade discounts. c. Include costs of labor and supervision directly attributable to the change. d. Include an updated Contractor's construction schedule that indicates the effect of the change, including, but not limited to, changes in activity duration, start and finish times, and activity relationship. Use available total float before requesting an extension of the Contract Time. e. Quotation Form: Use forms provided by Owner. B. Contractor-Initiated Proposals: If latent or changed conditions require modifications to the Contract, Contractor may initiate a claim by submitting a request for a change to Owner s Representative. CONTRACT MODIFICATION PROCEDURES ORANGEWALLstudios

28 Wahl Marine Boat General Requirements 17 April Include a statement outlining reasons for the change and the effect of the change on the Work. Provide a complete description of the proposed change. Indicate the effect of the proposed change on the Contract Sum and the Contract Time. 2. Include a list of quantities of products required or eliminated and unit costs, with total amount of purchases and credits to be made. If requested, furnish survey data to substantiate quantities. 3. Indicate applicable taxes, delivery charges, equipment rental, and amounts of trade discounts. 4. Include costs of labor and supervision directly attributable to the change. 5. Include an updated Contractor's construction schedule that indicates the effect of the change, including, but not limited to, changes in activity duration, start and finish times, and activity relationship. Use available total float before requesting an extension of the Contract Time. 6. Comply with requirements in Section "Substitution Procedures" if the proposed change requires substitution of one product or system for product or system specified. 7. Proposal Request Form: Use form provided by Owner. 1.5 ADMINISTRATIVE CHANGE ORDERS A. Allowance Adjustment: See Section "Allowances" for administrative procedures for preparation of Change Order Proposal for adjusting the Contract Sum to reflect actual costs of allowances. B. Unit-Price Adjustment: See Section "Unit Prices" for administrative procedures for preparation of Change Order Proposal for adjusting the Contract Sum to reflect measured scope of unit-price work. 1.6 CHANGE ORDER PROCEDURES A. On Owner's approval of a Work Change Proposal Request, Owner s Representative will issue a Change Order for signatures of Owner and Contractor on AIA Document G CONSTRUCTION CHANGE DIRECTIVE A. Construction Change Directive: Owner s Representative may issue a Construction Change Directive on AIA Document G714. Construction Change Directive instructs Contractor to proceed with a change in the Work, for subsequent inclusion in a Change Order. 1. Construction Change Directive contains a complete description of change in the Work. It also designates method to be followed to determine change in the Contract Sum or the Contract Time. B. Documentation: Maintain detailed records on a time and material basis of work required by the Construction Change Directive. 1. After completion of change, submit an itemized account and supporting data necessary to substantiate cost and time adjustments to the Contract. 1.8 WORK CHANGE DIRECTIVE A. Work Change Directive: Owner s Representative may issue a Work Change Directive on EJCDC Document C-940. Work Change Directive instructs Contractor to proceed with a change in the Work, for subsequent inclusion in a Change Order. 1. Work Change Directive contains a complete description of change in the Work. It also designates method to be followed to determine change in the Contract Sum or the Contract Time. CONTRACT MODIFICATION PROCEDURES ORANGEWALLstudios

29 Wahl Marine Boat General Requirements 17 April 2017 B. Documentation: Maintain detailed records on a time and material basis of work required by the Work Change Directive. 1. After completion of change, submit an itemized account and supporting data necessary to substantiate cost and time adjustments to the Contract. PART 2 - PRODUCTS (Not Used) PART 3 - EXECUTION (Not Used) END OF SECTION CONTRACT MODIFICATION PROCEDURES ORANGEWALLstudios

30 Wahl Marine Boat General Requirements 17 April 2017 SECTION PAYMENT PROCEDURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section includes administrative and procedural requirements necessary to prepare and process Applications for Payment. B. Related Requirements: 1. Section "Allowances" for procedural requirements governing the handling and processing of allowances. 2. Section "Contract Modification Procedures" for administrative procedures for handling changes to the Contract. 3. Section "Construction Progress Documentation" for administrative requirements governing the preparation and submittal of the Contractor's construction schedule. 1.3 DEFINITIONS A. Schedule of Values: A statement furnished by Contractor allocating portions of the Contract Sum to various portions of the Work and used as the basis for reviewing Contractor's Applications for Payment. 1.4 SCHEDULE OF VALUES A. Coordination: Coordinate preparation of the schedule of values with preparation of Contractor's construction schedule. 1. Coordinate line items in the schedule of values with items required to be indicated as separate activities in Contractor's construction schedule. 2. Submit the schedule of values to Owner s Representative at earliest possible date, but no later than seven days before the date scheduled for submittal of initial Applications for Payment. 3. Subschedules for Phased Work: Where the Work is separated into phases requiring separately phased payments, provide subschedules showing values coordinated with each phase of payment. 4. Subschedules for Separate Elements of Work: Where the Contractor's construction schedule defines separate elements of the Work, provide subschedules showing values coordinated with each element. 5. Subschedules for Separate Design Contracts: Where the Owner has retained design professionals under separate contracts who will each provide certification of payment requests, provide subschedules showing values coordinated with the scope of each design services contract, as described in Section "Summary." B. Format and Content: Use Project Manual table of contents as a guide to establish line items for the schedule of values. Provide at least one line item for each Specification Section. PAYMENT PROCEDURES ORANGEWALLstudios

31 Wahl Marine Boat General Requirements 17 April Identification: Include the following Project identification on the schedule of values: a. Project name and location. b. Name of Owner s Representative. c. Owner s Representative's Project number. d. Contractor's name and address. e. Date of submittal. 2. Arrange schedule of values consistent with format of AIA Document G Arrange the schedule of values in tabular form, with separate columns to indicate the following for each item listed: a. Related Specification Section or Division. b. Description of the Work. c. Name of subcontractor. d. Name of manufacturer or fabricator. e. Name of supplier. f. Change Orders (numbers) that affect value. g. Dollar value of the following, as a percentage of the Contract Sum to nearest one-hundredth percent, adjusted to total 100 percent. Round dollar amounts to whole dollars, with total equal to Contract Sum. 1) Labor. 2) Materials. 3) Equipment. 4. Provide a breakdown of the Contract Sum in enough detail to facilitate continued evaluation of Applications for Payment and progress reports. Provide multiple line items for principal subcontract amounts in excess of five percent of the Contract Sum. 5. Provide a separate line item in the schedule of values for each part of the Work where Applications for Payment may include materials or equipment purchased or fabricated and stored, but not yet installed. Differentiate between items stored on-site and items stored off-site. 6. Allowances: Provide a separate line item in the schedule of values for each allowance. Show line-item value of unit-cost allowances, as a product of the unit cost, multiplied by measured quantity. Use information indicated in the Contract Documents to determine quantities. 7. Purchase Contracts: Provide a separate line item in the schedule of values for each purchase contract. Show line-item value of purchase contract. Indicate Owner payments or deposits, if any, and balance to be paid by Contractor. 8. Overhead Costs: Include total cost and proportionate share of general overhead and profit for each line item. 9. Overhead Costs: Show cost of temporary facilities and other major cost items that are not direct cost of actual work-in-place as separate line items. 10. Closeout Costs. Include separate line items under Contractor and principal subcontracts for Project closeout requirements in an amount totaling five percent of the Contract Sum and subcontract amount. 11. Schedule of Values Revisions: Revise the schedule of values when Change Orders or Construction Change Directives result in a change in the Contract Sum. Include at least one separate line item for each Change Order and Construction Change Directive. 1.5 APPLICATIONS FOR PAYMENT A. Each Application for Payment following the initial Application for Payment shall be consistent with previous applications and payments as certified by Owner s Representative and paid for by Owner. B. Payment Application Times: The date for each progress payment is indicated in the Agreement between Owner and Contractor. The period of construction work covered by each Application for Payment is the period indicated in the Agreement. PAYMENT PROCEDURES ORANGEWALLstudios