LIGHTING TECHNICAL SHEET

Transcription

1 GENERAL INFORMATION LIGHTING TECHNICAL SHEET SMECO's Business Solutions program is designed to help commercial and industrial customers maximize energy efficiency and manage energy costs. With cost-saving financial incentives and expert technical assistance, SMECO's Business Solutions program identifies the right energy efficiency measures for your business. 1. Pre-approval is required for each of the following prior to purchasing and installing equipment is required: Retrofit Lighting applications that exceed $1,000 in incentives. Applications submitted pre-installation, regardless of incentive amount. Retrofit Lighting applications where s 153, 173, 183, 193, and/or 194 are applied for. New Construction Performance Lighting applications. A pre-installation inspection may also be required. 2. Upon receipt of approval, the Customer may begin project installation. Projects must be completed by the date indicated on the pre-approval letter. Customers must notify SMECO upon completion. If the project is completed in a manner different than what was indicated in the approved application, the Customer shall provide an explanation of what and why changes were made. Incentives will be determined based upon the actual qualified equipment installed. Copies of invoices for all work and equipment purchased are required. 3. A post-installation inspection may be required. 4. Upon final approval of the project, incentives will be paid to the Customer (account holder), or their designee, within four (4) weeks. To apply, please visit the Application Center. RETROFIT LIGHTING INSTRUCTIONS 1. Complete the room-by-room inventory worksheet using the Excel-based Retrofit Lighting Worksheet found on SMECO s Web site. Rated wattages for various existing luminaire types are found in SMECO s Lighting System Rated Wattage Table (included on the Retrofit Lighting Worksheet). 2. Meet measure code eligibility requirements. 3. Upload the completed electronic copy of the worksheet, as well as specification sheets (for all fixtures, lamps, and ballasts) under the tasks tab of your project in the Application Center. GENERAL LINEAR FLUORESCENT LAMP AND BALLAST REQUIREMENTS High-Performance T8 (HPT8), -Wattage T8, T5/T5HO lamps and qualifying ballasts are permitted for all measure codes unless specified otherwise in the lighting system eligibility requirements. 32w 4-ft T8 lamps and T8 ballasts must be listed on the Consortium for Energy Efficiency (CEE) product list or must meet CEE standards. Visit for further information. -wattage T8 lamps are acceptable provided they are on CEE s -Wattage T8 list. 8-ft T8 and 8-ft T5 lamps are not eligible for prescriptive lighting incentives. 17w 2-ft T8 lamps must have minimum efficacy of 75 mean lumens/watt. 32w U-bend T8 lamps must have minimum efficacy of 79 mean lumens/watt. Installing fewer lamps than what the fixture is designed for (i.e. installing a single lamp in a 2-lamp fixture) is not permissible without applying for and meeting Permanent Delamping, even in cases of lamp for lamp retrofits. GENERAL LED REQUIREMENTS LED replacement lamps, LED luminaires, and LED retrofit kits must be listed on the Design Lights Consortium or ENERGY STAR Qualified Products list. LED luminaires - Use of an LED interior fixture measure code requires Design Lights Consortium (DLC)-listed equipment to be selected from the Interior luminaire product category. Use of an exterior LED fixture measure code requires DLC-listed equipment to be selected from the Outdoor luminaire product category. LED retrofit kits - Use of an LED interior retrofit kit measure code requires DLC-listed equipment to be selected from the Interior Retrofit Kit product category. Use of an exterior LED retrofit kit measure code requires DLC-listed equipment to be selected from the Outdoor Retrofit Kit product category. Linear LED lamp replacements (TLEDs) - Use of an LED Linear Lamps measure code requires DLC-listed equipment to be selected from the Linear Replacement Lamp product category. Type B TLEDs, which contain an internal driver and are connected to line voltage (120/277v) through an existing fluorescent lampholder (i.e. tombstone ) are not permitted with this program. Please see measure code technical requirements for additional information. Installing fewer lamps than what the fixture is designed for (i.e. installing a single lamp in a 2-lamp fixture) is not permissible without applying for and meeting Permanent Delamping, even in cases of lamp for lamp retrofits. GENERAL CONTROL REQUIREMENTS Exterior luminaires are not eligible for control incentives. Contact us with any questions: Phone Fax Business@smeco.coop 01/06/2016 Page 1 of 11

2 NEW CONSTRUCTION PERFORMANCE LIGHTING ELIGIBILITY REQUIREMENTS LIGHTING TECHNICAL SHEET All projects must meet the following additional requirements to qualify for Performance Based Lighting incentives. Provide maintained lighting levels in accordance with the recommendations of the Illuminating Engineering Society of North America (IESNA). Provide high-quality lighting achieving appropriate levels of glare control, color rendering, lighting uniformity and other lighting quality parameters deemed necessary by SMECO. Major renovation projects must involve: o Removal of the entire existing lighting system and wiring o Redesign of the entire existing lighting system o Significant change to the actual function of the building through significant renovation, i.e., projects where a licensed professional architect or engineer has prepared and certified building plans for the change of use and reconstruction of an existing or vacant building or space. All project submittals must include the following supporting documentation: Lighting layout plans. Site-specific photometric reports or point-by-point lighting calculations, if deemed necessary by SMECO. Manufacturer s specification sheets for all luminaires, lamps and ballasts. Lighting fixture schedule including manufacturer, model number and rated wattage. Supporting calculations demonstrating installed lighting wattage. Project submittals must contain COMCHECK or equivalent reports to substantiate Lighting Power Density (LPD) claims. Incentives may be provided for reducing the LPD in watts per square foot from the baseline lighting design that complies with the Interior Power Lighting Allowance obtained from ASHRAE/IESNA Wattage reduction for either the space-by-space or building-area method must be at least 10% more efficient than code requirements to qualify for incentives. NEW CONSTRUCTION PERFORMANCE LIGHTING EQUIPMENT GUIDE All Performance Lighting calculations must be captured through the equipment section of the online application. No Performance Lighting Worksheet is required. The table below outlines the definition of the attributes that are required when submitting an application through the Application Center. Product Name Attribute Meaning Building Method Space Method AREA_LIT BUILDING_TYPE_SEL ELEC_UTIL_CUST_INCENTIVE ELIGIBILITY_STATUS_SEL HRS_OF_USE LOCATION NUMBER OF FIXTURES PROJECT TYPE Lighted Building Area (sq. ft.) Building Type Total Incentive Fixture Level of Achievement Estimated Annual Hours of Operation Lighting Location Interior / Exterior Total Number of Fixtures Leave Blank QUANTITY This should always be "1" WATTAGE_NEW AREA_LIT BUILDING_TYPE_SEL CAVITY_RATIO CONTROL_TYPE_SEL ELEC_UTIL_CUST_INCENTIVE GEOMETRY_ADJUSTED_SPACES HRS_OF_USE LOCATION MANUFACTURER NUMBER OF FIXTURES Installed Wattage (W) Lighted Area for Space Type (sq ft.) Business Type Space Room Cavity Ratio or Corridor Width in Feet Control Method Total Incentive Lighted Area for Geometry Adjustment Spaces (sq ft.) Estimated Annual Hours of Operation Lighting Location Interior / Exterior Leave Blank Total Number of Fixtures Quantity This should always be "1" SPACE_TYPE_SEL WATTAGE_NEW WATTS_CONTROLLED Individual Space Types Installed Wattage (W) Lighting Power Under Control (watts) 01/06/2016 Page 2 of 11

3 RETROFIT LIGHTING MEASURES AND INCENTIVES FLUORESCENT SOLUTIONS FLUORESCENT LAMP AND BALLAST RETROFITS 11c Relamp & Reballast with HPT8, RWT8, or T5/T5HO Lamps & Ballasts (Existing 1- & 2- lamp 4-ft fixtures, including U-bends) 10 $15/Fixture 11d Relamp & Reballast with HPT8, RWT8, or T5/T5HO Lamps and Ballasts (Existing 3- & 4-lamp 4-ft fixtures) 15 $25/Fixture 12c Relamp & Reballast with HPT8 / RWT8 Ballasts, or T5/T5HO Lamps and Ballasts (Existing T8, 1- & 2-Lamp, 2-ft and 3-ft fixtures, including U-bends) 10 $10/Fixture All Relamp & Reballast s require a lamp-for-lamp replacement and installation of a new, compatible ballast in existing fixtures. 12d Relamp & Reballast with HPT8 or RWT8 Ballasts, or T5/T5HO Lamps and Ballasts (Existing T8, 3- & 4-Lamp, 2-ft and 3-ft fixtures) 15 $15/Fixture 12e Relamp & Reballast with HPT8, RWT8, or T5/T5HO Lamps and Ballasts (Existing T8, 6-lamp 4-ft fixtures) 25 $35/Fixture 12f Relamp & Reballast with HPT8, RWT8, or T5/T5HO Lamps and Ballasts (Existing T8, 8-lamp 4-ft fixtures) 25 $35/Fixture 01/06/2016 Page 3 of 11

4 15a 15b 15c 15d De-lamp/Retrofit with HPT8 or T5/T5HO 4- ft Lamps and Ballasts with existing 4-ft fixtures containing two, three, or four 4-ft lamps or existing 8-ft fixtures containing one or two 8-ft lamps or existing fixtures with U-bends De-lamp/Retrofit with HPT8 or T5/T5HO 4- ft Lamps and Ballasts with existing 4-ft and 8-ft fixtures with three or four 4-ft or 8-ft lamps De-lamp/Retrofit with HPT8 or T5/T5HO Lamps and Ballasts and Retrofit Kit with existing 5- to 8-lamp 4-ft fixtures De-lamp/Retrofit with HPT8 or T5/T5HO Lamps & Ballasts with existing 2- and 4- lamp fixtures including those with U-bend lamps PERMANENT DELAMPING 28 $25/Fixture 30 $40/Fixture 65 $60/Fixture 20 $25/Fixture Luminaires must be permanently delamped through the use of UL / CSA-listed retrofit kits specifically for this purpose; lamps must be re-centered in luminaires. Light levels may be affected; therefore, delamping may not be appropriate for all applications. Reflectors, if specified, shall have a minimum reflectivity of 90% and should be used if necessary to provide proper lighting levels or quality. COMMODITY FIXTURES 20a New Fixture with Qualifying T8 Lamps, HPT8, RWT8 Lamps and Ballasts, or T5/T5HO Lamps and Ballasts (1 or 2, 2-ft or 3-ft Lamps) 10 $20/Fixture 20b New Fixture with Qualifying T8 Lamps, HPT8, RWT8 Lamps and Ballasts, or T5/T5HO Lamps and Ballasts (3 or 4, 2-ft and 3-ft Lamps) 15 $25/Fixture 20c 20d 20e New Fixture with Qualifying HPT8, RWT8, or T5/T5HO Lamps and Ballasts (1 or 2, 4-ft Lamps and U-Bend Lamps) New Fixture with Qualifying HPT8, RWT8, or T5/T5HO Lamps and Ballasts (3 or 4, 4-ft New Fixture with HPT8, RWT8, or T5/T5HO Lamps and Ballasts (5 to 8, 4-ft Lamps) 15 $25/Fixture 20 $30/Fixture 65 $35/Fixture Commodity-grade fixtures include most standard troffers, strips, wraps, and vapor-tight fixtures 20f New Fixture with HPT8, RWT8, or T5/T5HO Lamps and Ballasts (> 8, 4-ft Lamps) 65 $40/Fixture 25 New Self-Contained Fixture with Qualifying HPT8, RWT8 Lamps and Ballast, or T5/T5HO Lamps and Ballasts (1 or 2, 2-ft, 3-ft, or 4-ft Lamps, or 1 or more CFLs with Integral Occupancy Sensor Controlling Some Lamps) N/A $50/Fixture Installation of self-contained, occupancy-based luminaires in in a stairwell Eligible fixtures contain onboard, factory-furnished occupancy controls and are designed for stairwells and other seldom- occupied spaces Standby (unoccupied) mode may be accomplished with the use of separate low-wattage fluorescent or CFL lamp or step- dimming ballast The total wattage of the proposed fixture cannot be more than the existing fixture FLUORESCENT HIGH BAY FIXTURES 62 New Fluorescent T5HO/HPT8 High/Low Bay Fixture; Replacing a total lamp wattage of 251Ww 400w HID. 70 $55/Fixture Luminaires must be installed greater than or equal to 15-ft above finished floor (AFF). Overall fixture efficiency must be > 80%. 01/06/2016 Page 4 of 11

5 63 New Fluorescent T5HO/HPT8 High Bay Fixture; Replacing a total lamp wattage of > 401w HID. FLUORESCENT HIGH BAY FIXTURES CONT. 200 $85/Fixture COMPACT FLUORESCENT 71a New CFL Fixture 42w 12 $25/Fixture 71b New CFL Fixture > 42w 60w 12 $30/Fixture 71c New CFL Fixture > 60w 12 $35/Fixture 71d New CFL Fixture with Dimmable Ballast 12 $40/Fixture 71e Retrofit with CFL 42w 12 $15/Fixture 71f Retrofit CFL > 42w to 60w 12 $20/Fixture 71g Retrofit CFL > 60w 12 $25/Fixture LED INTERIOR SOLUTIONS Screw in CFL lamps are not eligible Integral LED replacement lamps - Specialty (candelabra, globe, tip) Integral LED replacement lamps - PAR, BR, R, MR less than size 30 Integral LED replacement lamps - PAR, BR, R greater than or equal to size 30 Integral LED replacement lamps - Standard A Line LED INTEGRAL REPLACEMENT LAMPS 5 $5/Lamp 5 $5/Lamp 5 $10/Lamp 5 $3/Lamp LED LINEAR LAMPS (TLEDS) 116 Replacement of an existing linear fluorescent lamp with a Type A LED linear lamp & new fluorescent ballast 10 $5/Lamp Type A LED linear lamps are powered by a fluorescent ballast. Existing fluorescent ballast must be removed and replaced with a compatible, energy-efficient ballast. DLC Primary Use Requirement DLC-listed equipment must be classified with the following Primary Use designation: o Replacement Lamps ( Plug and Play ) (UL Type A) It is encouraged that a label be affixed to the interior of the fixture in a prominent location. Label should indicate that the fixture has been retrofitted with TLEDs and that fluorescent lamps should not be installed as replacements. Incentive capped at 4 lamps / $20 per fixture. 117 Replacement of an existing linear fluorescent lamp with a Type C LED linear lamp & new LED driver 10 $10/Lamp Type C LED linear lamps are powered by an external driver. Existing fluorescent ballast must be removed and replaced with a compatible external driver. DLC Primary Use Requirement DLC-listed equipment must be classified with one of the following Primary Use designations : o 2-lamp External Driver Lamp-Style Retrofit Kits (UL Type C) o 3-lamp External Driver Style Retrofit Kits (UL Type C) o 4-lamp External Driver Lamp-Style Retrofit Kits (UL Type C) Technical specifications (manufacturer s cut sheet) for the driver must be submitted with the application. Incentive capped at 4 lamps / $40 per fixture. 01/06/2016 Page 5 of 11

6 LED LINEAR LAMPS (TLEDS) CONT. 118 Permanent Delamping/Retrofit: Retrofit existing linear fluorescent fixture with a retrofit kit containing LED linear lamps (Type A or Type C only) 40 $50/Fixture All technical requirements for s 116 and 117 apply for 118. If proposing to install TLEDs in existing fixtures using a delamping approach (e.g. installing 2 TLEDs in place of 4 fluorescent lamps), the luminaires must be permanently delamped and the TLEDs re-centered in luminaires through the use of UL/CSA-listed retrofit kits specifically-made for this purpose. No additional incentives shall be offered for delamping using TLED technology. Light levels may be affected; therefore, delamping may not be appropriate for all applications. If you have a delamping scenario and are not able to meet the wattage reduction requirement, you may apply for s 116 or 117 and receive an incentive per lamp instead. If this option is exercised, you must still meet the for MC 118 (installation of a UL/CSA-listed retrofit kit, etc.). LED RETROFIT KITS 121 LED retrofit kit for downlights 5 $15/Fixture Trim kits may be installed in recessed cans less than 8 in diameter. 122 LED retrofit kit (replacing fixtures containing 2 lamps) 25 $40/Fixture Must use this measure code for the following installed retrofit kit dimensions: 2x2 and 1x4. Must use this measure code if existing 2x4 fixtures contain 2 lamps. May apply for recessed trim retrofit kits with this measure code if installing in recessed cans 8 or greater in diameter or utilizing high output trim kits. 123 LED retrofit kit (replacing fixtures containing 3 or more lamps) 40 $60/Fixture Retrofit Kits o Must use this measure code if existing 2x4 fixtures contain 3 or more lamps or if installed retrofit kit dimension is 4x4. HID Replacement Lamps (HLEDs) o Type C HLED lamps are powered by an external driver. o Existing HID ballast must be removed and replaced with a compatible external driver. o DLC Primary Use Requirement DLC-listed equipment for HID replacement lamps (HLEDs) must be selected with one of the following primary use designations: Replacement Lamps for High-Bay Luminaires (Type C) Replacement Lamps for Low-Bay Luminaires (Type C) LED RECESSED/SURFACE-MOUNTED/SUSPENDED LUMINAIRES 90 LED exit signs 5 $10/Sign 01/06/2016 Page 6 of 11

7 LED RECESSED/SURFACE-MOUNTED/SUSPENDED LUMINAIRES CONT. 95 LED strip fixture for reach-in coolers/freezers N/A $45/Strip DLC Primary Use Requirement DLC-listed equipment must be selected with one of the following primary use designations: o Vertical Refrigerated Case Luminaires (center/end) o Horizontal Refrigerated Case Luminaires 131 New LED recessed or surface-mounted downlight 15 $40/Fixture Recessed downlight fixtures must have a new housing installed to qualify. 133 New LED surface-mounted or industrial suspended fixture 25 $60/Fixture Examples of linear LED surface-mounted luminaires include: wrap, vaportight, and strip fixtures (non-cooler). 134 New LED linear recessed troffer/panel fixture (replacing fixtures containing 2 lamps) 25 $60/Fixture Must use this measure code for the following installed fixture dimensions: 2x2 and 1x4. Must use this measure code if existing 2x4 fixtures contain 2 lamps. 135 New LED linear recessed troffer/panel fixture (replacing fixtures containing 3 or more lamps) 50 $90/Fixture Must use this measure code for existing 2x4 fixtures that contain 3 or more lamps and installed 4x4 fixtures. 136 New LED stairwell fixture containing factory-installed integrated occupancy/vacancy control NA $115/Fixture Installation of self-contained occupancy-based luminaires in stairwells. Eligible fixtures contain on-board, factory-installed occupancy controls and are designed for stairwells and other seldom-occupied spaces. The total wattage of the proposed fixture cannot be more than the existing fixture. Control incentive is included. May not apply for additional incentives for the control. LED DECORATIVE/ ARCHITECTURAL/ SUSPENDED LIGHTING 141 New LED decorative pendant fixture 15 $40/Fixture 142 New LED track fixture 15 $40/Head 143 New LED wall sconce 25 $60/Fixture Decorative pendant fixtures must be self-contained. This measure code may not be used if installing a new fixture designed to carry an LED replacement lamp. In that scenario, you may only apply for an applicable replacement lamp measure code. Track fixtures must be self-contained. This measure code may not be used if installing a new fixture designed to carry an LED replacement lamp. In that scenario, you may only apply for an applicable replacement lamp measure code. Wall sconce fixtures must be self-contained. This measure code may not be used if installing a new fixture designed to carry an LED replacement lamp. In that scenario, you may only apply for an applicable replacement lamp measure code. 144 New LED suspended architectural-style fixture 5 $20/Foot Fixture must be considered an architectural-style fixture. A wattage reduction of 5 watts per foot is required for every foot installed (Ex: 4 ft. fixture requires a wattage reduction of 20 watts). 01/06/2016 Page 7 of 11

8 LED LOW/HIGH BAY LUMINAIRES New LED Low/High Bay fixture replacing a fixture containing total lamp wattage less than or equal to 175W New LED Low/High Bay fixture replacing a fixture containing total lamp wattage 176W - 400W 60 $100/Fixture 150 $200/Fixture DLC Primary Use Requirement For s , DLC-listed equipment must be selected with one of the following primary use designations: o Low-bay Luminaires for Commercial and Industrial Building o High-bay Luminaires for Commercial and Industrial Buildings o High-bay Aisle Luminaires Luminaires must be installed greater than or equal to 15- ft. above finished floor (AFF). 153 New LED Low/High Bay fixture replacing a fixture containing total lamp wattage greater than or equal to 401W 500 $400/Fixture LED EXTERIOR SOLUTIONS Pre-approval Requirement - MC 153 Pre-approval required for use of this measure code, regardless of quantity applied for. May not remove existing fixtures or purchase new fixtures until Preapproval is obtained. 161 New LED pathway/landscape fixture (includes mini-bollards) LED PATHWAY/PERIMETER LUMINAIRES & RETROFIT KITS 10 $15/Fixture 162 New LED soffit/overhang fixture 25 $50/Fixture 163 New LED perimeter fixture/retrofit kit replacing total lamp wattage less than or equal to 50W 30 $60/Fixture Perimeter Luminaires Qualified fixtures can include bollards, canopy fixtures not installed in fuel station canopies or parking garages, wall sconces, etc. LED wall sconces must be self-contained and may only apply using MC 163, regardless of existing lamp wattage. Retrofit Kits 164 New LED perimeter fixture/retrofit kit replacing total lamp wattage greater than or equal to 51W 45 $90/Fixture Recessed downlight retrofit trim kits are not permitted under these s. These trim kits must be applied for using s 121 or 122 (based on ). HID Replacement Lamps (HLEDs) Type C HLED lamps are powered by an external driver. Existing HID ballast must be removed and replaced with a compatible external driver. DLC Primary Use Requirement DLC-listed equipment for HID replacement lamps (HLEDs) must be selected with one of the following primary use designations: o Replacement Lamps for Outdoor Pole/Arm- Mounted and Roadway Luminaires (Type C) o Replacement Lamps for Outdoor Pole-Arm- Mounted Decorative Luminaires (Type C) o Replacement Lamps for Outdoor Full-Cutoff Wallmounted Area Luminaires (Type C) o Replacement Lamps for Parking Garage Luminaires (Type C) o Replacement Lamps for Fuel Pump Canopy Luminaires (Type C) 01/06/2016 Page 8 of 11

9 LED FLOOD LIGHTS/ WALLPACKS 171 New LED flood light or wallpack replacing an existing fixture containing total lamp wattage less than or equal to 175W 35 $60/Fixture New LED flood light or wallpack replacing an existing fixture containing total lamp wattage of 176W - 400W New LED flood light or wallpack replacing an existing fixture containing total lamp wattage greater than or equal to 401W 125 $130/Fixture 300 $250/Fixture All building-mounted fixtures that are non-decorative in nature should apply using these measure codes. Decorative fixtures, such as wall sconces, must be applied for using 163. Pre-approval Requirement - MC 173 Pre-approval required for use of this measure code, regardless of quantity applied for. May not remove existing fixtures or purchase new fixtures until Preapproval is obtained. LED PARKING GARAGE/ GAS STATION CANOPY LUMINAIRES New LED parking garage or gas station canopy fixture replacing a fixture containing total lamp wattage less than or equal to 175W New LED parking garage or gas station canopy fixture replacing a fixture containing total lamp wattage 176W - 250W New LED parking garage or gas station canopy fixture replacing a fixture containing total lamp wattage greater than 251W 50 $100/Fixture 150 $175/Fixture 250 $275/Fixture Fixtures must be physically installed in a parking garage (area where vehicles are physically parked) or fuel pump canopy. DLC Primary Use Requirement For s , DLC-listed equipment must be selected with one of the following primary use designations: o Parking Garage Luminaires (for parking garage installations) o Fuel Pump Canopy Luminaires (for fuel pump canopy installations) Pre-approval Requirement - MC 183 Pre-approval required for use of this measure code, regardless of quantity applied for. May not remove existing fixtures or purchase new fixtures until Preapproval is obtained. LED POLE-MOUNTED PARKING LOT/ AREA LUMINAIRES 191 New LED pole-mounted parking lot/area fixture replacing a fixture containing total lamp wattage of less than or equal to 250W 60 $100/Fixture New LED pole-mounted parking lot/area fixture replacing a fixture containing total lamp wattage 251W - 400W New LED pole-mounted parking lot/area fixture replacing a fixture containing total lamp wattage 401W - 750W 150 $225/Fixture 250 $275/Fixture Pre-approval Requirement - MC 193 and MC 194 Pre-approval required for use of these measure codes, regardless of quantity applied for. May not remove existing fixtures or purchase new fixtures until Preapproval is obtained. 194 New LED pole-mounted parking lot/area fixture replacing a fixture containing total lamp wattage greater than or equal to 751W 500 $400/Fixture 01/06/2016 Page 9 of 11

10 81 82 Occupancy Control Wall Mount wall switch Occupancy Control Ceiling/Wall Mount (Remote) LIGHTING CONTROLS 25 $25/Control 75 $75/Control 83 Occupancy Control Fixture Mounted 25 $25/Control Daylight Control Continuous dimming dimming ballasts Daylight Control On/off control standard ballasts Occupancy Controls LED Reach-in freezer or cooler lighting Occupancy Controls with Step-Dimming Capability N/A 40 $40/Ballast or Driver $75/Ballast or Driver $9/Door $40/Ballast or Driver Hardwired wall switch occupancy control; passive infrared, ultrasonic or dual technology Occupancy controls with manual on override are not eligible for incentives Hardwired or wireless ceiling or wall-mounted remote occupancy control; passive infrared, ultrasonic or dual technology Occupancy controls with manual on override are not eligible for incentives Hardwired fixture-mounted occupancy controls; passive infrared, ultrasonic or dual technology Controls may be furnished as new equipment by fixture manufacturer or installed on existing fixtures in retrofit applications Control must dim lamps in response to ambient daylight Control must extinguish lamps in response to ambient daylight Control must be designed to operate refrigerated case strips Controls may be installed at end of aisle or on individual cases Occupancy control design to reduce light levels to pre-set levels based on occupancy NEW CONSTRUCTION PERFORMANCE LIGHTING MEASURES AND INCENTIVES NEW CONSTRUCTION Tier 1 > 10% below Base LPD $0.40 per watt* Tier 2 > 20% below Base LPD $0.80 per watt* Tier 1 Tier 2 All Performance Lighting calculations will be performed through the equipment section of the application. No Performance Lighting Worksheet is required. Refer to the guide on page 2 on how to select the appropriate equipment in the Application Center. *Subject to a $30/fixture cap ** All New Construction Performance Lighting applications require pre-approval Contact us with any questions: Phone Fax Business@smeco.coop This program supports EmPOWER Maryland. 01/06/2016 Page 10 of 11

11 TERMS & CONDITIONS 1. ELIGIBILITY: Incentives are available to SMECO non-residential Customers for the purchase and installation of qualifying energy conservation measures (ECMs) in the SMECO service territory, subject to these Terms and Conditions (T&Cs). SMECO reserves the right to deny any application that may result in SMECO exceeding its program budget. Incentives are offered on a first-come, first served basis and are subject to project and Customer eligibility and availability of funds. 2. AUTHORIZATION, PROGRAM CHANGES, SUSPENSION, OR CANCELLATION: SMECO may change the program requirements, incentives or T&Cs, including suspending acceptance of applications or terminating the program, at any time without notice. In the event of a program change, pre-approved applications will be processed to completion under the T&Cs in effect at time of pre-approval. Submission of a completed application does not entitle the Customer to program participation. For projects requiring pre-approval entitlement to program participation, SMECO s obligation to pay incentives will occur only after SMECO has granted written authorization, which SMECO may approve or disapprove at its sole discretion. 3. PROJECT APPROVAL: Pre-approval is required for all Custom projects as well as all Prescriptive projects qualifying for a total incentive greater than $1,000. SMECO reserves the right to pre-inspect any project prior to pre-approval. No project-related ECMs may be ordered or installed prior to the date of SMECO s pre-approval. Prescriptive projects qualifying for a total incentive of less than $1,000 must be purchased within 3 months of the date SMECO receives the application. 4. PROOF OF PURCHASE: Prior to SMECO s verification of the ECM installation, the Customer must provide copies of all invoices or other reasonable documentation that verify the costs of purchasing and installing the ECMs, including all material, labor, and equipment discounts. Invoices must indicate a verifiable breakout of all ECMs purchased for installation under this application. 5. PROJECT VERIFICATION: SMECO is not obligated to pay any incentive until it has performed a satisfactory post-installation inspection. If SMECO determines that ECMs were not installed in a manner consistent with the approved application, or if an unapproved ECM was installed, or if the installation was not consistent with generally accepted engineering practices, changes may be required before payment is issued. 6. CUSTOMER TAX OBLIGATION: The Customer or its designated contractor is responsible for declaring and paying any and all applicable federal, state, and local taxes that may be owed on any incentive payment. 7. COMPLIANCE: The Customer is responsible for obtaining any and all necessary licenses and permits related to the installation of ECMs. The Customer also agrees to comply with all federal, state, and local laws and regulations related to the installation and disposal of all equipment. 8. REMOVAL OF EQUIPMENT: The Customer agrees to remove and dispose of the equipment being replaced by the ECMs in accordance with all legal requirements. The Customer agrees not to re-install any of this equipment in the SMECO service territory or transfer it to any other party for such installation. 9. REPLACEMENT OF FAILED EQUIPMENT: Customers who install ECMs are expected to replace any of the ECMs that fail with similar or superior energy-saving equipment at the Customer s expense. 10. EVALUATION FOLLOW-UP VISITS: With advance notice, SMECO reserves the right to make follow-up visits to Customer facilities during the 36 months following the actual completion of the project to provide SMECO with an opportunity to review the operation of the ECMs for program evaluation purposes. 11. CONTRACTOR SELECTION: The Customer may select any contractor to perform the work contemplated by the application, whether a SMECO Trade Ally or not. However, SMECO reserves the right, in its sole reasonable discretion, to prohibit specific contractors from program participation. 12. NO WARRANTIES: SMECO does not endorse, guarantee, or warrant any particular manufacturer or product, and SMECO provides no warranties, expressed or implied, for any products or services. SMECO is not liable or responsible for any act or omission of any contractor hired by the Customer (if any) whether or not said contractor is a participating SMECO Trade Ally. The Customer s reliance on warranties is limited to any warranties that may arise from or be provided by contractors, vendors, etc. The Customer acknowledges that neither SMECO nor any of its consultants is responsible for ensuring that the design, engineering, and construction of the facility or installation of the ECMs is proper or complies with any particular laws (including patent laws), codes, or industry standards. SMECO does not make any representations of any kind regarding the results to be achieved by the ECMs or the adequacy of safety of such measures. 13. LIMITATION OF LIABILITY: SMECO s sole liability is limited to paying the properly qualified rebates specified herein. SMECO shall not be liable to the Customer or any other party for any indirect, consequential, or incidental damages, regardless of the theory of recovery, caused by or arising from any activities associated with this program. 14. OBLIGATIONS BETWEEN THE PARTIES: Customer acknowledges that any contractor selected by the Customer is not an agent, contractor, or subcontractor of SMECO and is an independent contractor engaged by the Customer, and that SMECO does not manage or control the contractor s performance. SMECO shall have no obligation to maintain, remove, or perform any work whatsoever on the ECMs installed. SMECO shall have no liability for contractor s failure to perform, for failure of the ECMs to function, for any damage to the Customer s premises caused by the contractor, or for any and all damages to property or injuries to persons caused by the ECMs. 15. ENERGY BENEFITS: SMECO is entitled to 100% of the energy benefits associated with the ECMs, excluding the value of energy cost savings realized by the Customer, but including all rights to all associated PJM Energy, Capacity and Reserves Products, and applicable environmental credits. The Customer agrees to provide SMECO with such further documentation as SMECO may request to confirm SMECO s ownership of such benefits and products. 16. MISCELLANEOUS: These T&Cs and this application constitute the entire agreement between the parties and supersede all other communications and representations. 01/06/2016 Page 11 of 11