Missouri S&T Bullman Showers Date: February 13, 2017 Project No SECTION PLASTIC SHOWER AND DRESSING COMPARTMENTS

Transcription

1 SECTION PLASTIC SHOWER AND DRESSING COMPARTMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Solid-plastic compartments. 1.3 ACTION SUBMITTALS A. Product Data: For each type of product. 1. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes. B. Shop Drawings: For shower and dressing compartments. 1. Include plans, elevations, sections, and attachment details. 2. Show locations of cutouts for compartment-mounted accessories. C. Samples for Verification: For the following products, in manufacturer's standard sizes unless otherwise indicated: 1. Each type of material, color, and finish required for compartments, preparedon6-inchsquare Samples of same thickness and material indicated for the Work. 2. Each type of hardware and accessory. 1.4 INFORMATIONAL SUBMITTALS A. Product Certificates: For each type of shower and dressing compartment. 1.5 CLOSEOUT SUBMITTALS A. Maintenance Data: For shower and dressing compartments to include in maintenance manuals. 1.6 FIELD CONDITIONS A. Field Measurements: Verify actual locations of fixtures, drains, walls, columns, ceilings, and other construction contiguous with shower and dressing compartments by field measurements before fabrication. PLASTIC SHOWER AND DRESSING COMPARTMENTS

2 PART 2 - PRODUCTS 2.1 PERFORMANCE REQUIREMENTS A. Surface-Burning Characteristics: Comply with ASTM E 84 or UL 723; testing by a qualified testing agency. Identify products with appropriate markings of applicable testing agency. B. Accessibility Standard: Comply with applicable provisions in the U.S. Architectural & Transportation Barriers Compliance Board's ADA-ABA Accessibility Guidelines for Buildings and Facilities for shower and dressing compartments designated as accessible. 2.2 SOLID-PLASTIC COMPARTMENTS < (REF. DRAWINGS FOR QUANTITY AND LOCATIONS)> A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: B. Basis-of-Design Product: Subject to compliance with requirements, provide Scranton Shower Dividers or comparable product by one of the following: 1. Accurate Partitions Corporation. 2. General Partitions Mfg. Corp. 3. Scranton Products. C. Configuration: Shower compartment. D. Enclosure Style: Overhead braced. E. Panel and Pilaster Construction: Solid, high-density polyethylene (HDPE) panel material, not less than 1 inch thick, seamless, with eased edges and with homogenous color and pattern throughout thickness of material. 1. Integral Hinges: Configure doors and pilasters to receive integral hinges. 2. Color and Pattern: One color and pattern in each room; as selected by Architect from manufacturer's full range See Appendix A Interior Finish Key. 3. Height of dividing panels to align with overhead bracing F. Door Construction: Match panels. Equip door and pilasters with manufacturer's standard nosightline system. G. Pilaster Shoes and Sleeves (Caps): Manufacturer's standard design; stainless steel. 1. Plastic Color and Pattern: Match pilaster. 2.3 MATERIALS A. Aluminum Castings: ASTM B 26/B 26M. B. Aluminum Extrusions: ASTM B 221. PLASTIC SHOWER AND DRESSING COMPARTMENTS

3 2.4 ACCESSORIES A. Door Hardware and Accessories: Manufacturer's standard design, heavy-duty, operating hardware and accessories. Mount to panels with through-bolts. 1. Material: Clear-anodized aluminum. 2. Hinges: Manufacturer's standard, integral hinge for solid-plastic doors, allowing emergency access by lifting door. 3. Latch and Keeper: Manufacturer's standard, surface-mounted latch unit designed for emergency access and with combination rubber-faced door strike and keeper. Provide units that comply with regulatory requirements for accessibility at compartments designated as accessible. B. Overhead Bracing: Manufacturer's standard, continuous, extruded-aluminum headrail or cap with antigrip profile; in manufacturer's standard finish. C. Headrail with Hooks: Manufacturer's standard, continuous, extruded-aluminum headrail or cap with curtain hooks running in concealed track; with antigrip profile; in manufacturer's standard finish. D. Curtain Rod with Hooks: Manufacturer's standard, 1-inch- diameter, stainless-steel curtain rod with matching hooks. E. Anchorages and Fasteners: Manufacturer's standard, exposed fasteners of stainless steel, chrome-plated steel, or solid brass, finished to match the items they are securing; with theftresistant-type heads. Provide sex-type bolts for through-bolt applications. Use countersunk, flush-type bolt heads or otherwise make fasteners inconspicuous if exposed on opposite side of panel from hardware or accessory item. For concealed anchors, use stainless steel, hot-dip galvanized steel, or other rust-resistant, protective-coated steel. 2.5 FABRICATION A. Overhead-Braced Compartments: Manufacturer's standard, corrosion-resistant supports, leveling method, and anchors at pilasters and walls to suit floor and wall conditions. Provide shoes at pilasters to conceal supports and leveling method. B. Door Sizes and Swings: Unless otherwise indicated, provide 24-inch- wide, doors for standard shower compartments, and 36-inch- wide, outswinging doors with a minimum 32-inch- wide, clear opening for compartments designated as accessible. PART 3 - EXECUTION 3.1 INSTALLATION A. General: Comply with manufacturer's written installation instructions. Install compartments rigid, straight, level, and plumb. Secure compartments in position with manufacturer's recommended anchoring devices. 1. Clearances for Dressing Compartments: Maximum 1/2 inch between pilasters and panels; 1 inch between panels and walls. PLASTIC SHOWER AND DRESSING COMPARTMENTS

4 2. Full-Height (Continuous) Brackets for Compartments: Secure panels to walls and to pilasters with full-height brackets. a. Locate bracket fasteners so holes for wall anchors occur in masonry or tile joints. b. Align brackets at pilasters with brackets at walls. B. Overhead-Braced Compartments: Secure pilasters to floor, and level, plumb, and tighten. Set pilasters with anchors penetrating not less than 1-3/4 inches into structural floor unless otherwise indicated in manufacturer's written instructions. Secure continuous headrail to each pilaster with no fewer than two fasteners. Hang doors to align tops of doors with tops of panels, and adjust so tops of doors are parallel with overhead brace when doors are in closed position. C. Curtains: Install curtains to specified length, and verify that they hang vertically without stress points or diagonal folds. 3.2 ADJUSTING A. Curtain Adjustment: After hanging curtains, test and adjust each track or rod to produce unencumbered, smooth operation. Steam and dress down curtains as required to produce creaseand wrinkle-free installation. Remove and replace curtains that are stained or soiled or that have stress points or diagonal folds. B. Hardware Adjustment: Adjust and lubricate hardware according to hardware manufacturer's written instructions for proper operation. Set hinges on inswinging doors to hold doors open approximately 30 degrees from closed position when unlatched. Set hinges on outswinging doors to return doors to fully closed position. END OF SECTION PLASTIC SHOWER AND DRESSING COMPARTMENTS

5 SECTION TOILET, BATH, AND LAUNDRY ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Public-use washroom accessories. 2. Public-use shower room accessories. 3. Warm-air dryers. 1.3 COORDINATION A. Coordinate accessory locations with other work to prevent interference with clearances required for access by people with disabilities, and for proper installation, adjustment, operation, cleaning, and servicing of accessories. B. Deliver inserts and anchoring devices set into concrete or masonry as required to prevent delaying the Work. 1.4 ACTION SUBMITTALS A. Product Data: For each type of product. 1. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes. 2. Include anchoring and mounting requirements, including requirements for cutouts in other work and substrate preparation. 3. Include electrical characteristics. B. Product Schedule: Indicating types, quantities, sizes, and installation locations by room of each accessory required. 1.5 INFORMATIONAL SUBMITTALS A. Sample Warranty: For manufacturer's special warranty. 1.6 CLOSEOUT SUBMITTALS A. Maintenance Data: For accessories to include in maintenance manuals. TOILET, BATH, AND LAUNDRY ACCESSORIES

6 PART 2 - PRODUCTS 2.1 PERFORMANCE REQUIREMENTS A. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application. 2.2 PUBLIC-USE WASHROOM ACCESSORIES A. Grab Bar: GB18 & GB48 on drawings (Ref. drawings for quantity, lengths and locations): 1. Manufacturers: Subject to compliance with requirements, provide products by the following: 2. Basis-of-Design Product: Subject to compliance with requirements, provide Bobrick; B5806 x 48 horizontal and B5806 x 18 vertical or comparable product by one of the following: 3. Mounting: Flanges with concealed fasteners. 4. Material: Stainlesssteel,0.05 inch thick. a. Finish: Smooth, No. 4 finish (satin). 5. Outside Diameter: 1-1/4 inches. 6. Mounting Height: Horizontal grab bars 2'-10" to top of bar. Vertical grab bar 39" to center of bottom mounting flange. B. Mirror Unit (Ref. drawings for quantity, lengths and locations): 1. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 2. Basis-of-Design Product: Subject to compliance with requirements, provide product indicated on Drawings Bobrick, B290-24x36 or comparable product by one of the following: 3. Frame: Stainless-steel angle, 0.05 inch thick. a. Corners: Manufacturer's standard. 4. Hangers: Produce rigid, tamper- and theft-resistant installation, using method indicated below. a. One-piece, galvanized-steel, wall-hanger device with spring-action locking mechanism to hold mirror unit in position with no exposed screws or bolts. 5. Size: 24"w X 36"h. TOILET, BATH, AND LAUNDRY ACCESSORIES

7 6. Mounting Height: 3'-4" max to bottom of reflective surface 2.3 PUBLIC-USE SHOWER ROOM ACCESSORIES A. Source Limitations: Obtain public-use shower room accessories from single source from single manufacturer. B. Shower Curtain Rod: SR on drawings (Ref. drawings for quantity, lengths and locations): 1. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 2. Basis-of-Design Product: Subject to compliance with requirements, provide Bobrick; B207 Heavy Duty Shower Curtain Rod with Concealed Mounting or comparable product by one of the following: 3. Description: 1-inch OD; fabricated from nominal inch- thick stainless steel. 4. Mounting Flanges: Chrome plated plastic. Bright polished finish. 5. Finish: Stainless steel, No. 4 finish (satin). 6. Mounting Height: 77" above finished floor to top of curtain rod C. Shower Curtain and Stainless Steel Shower Curtain Hooks: SR on drawings (Ref. drawings for quantity, lengths and locations) : 1. Basis-of-Design Product: Subject to compliance with requirements, provide Bobrick - Vinyl Shower Curtain Model 204 andstainless Steel Shower Curtain Hooks or comparable product by one of the following: 2. Size: Minimum 12 inches wider than opening by 72 inches high. 3. Material: Vinyl, minimum inch thick, opaque, matte. 4. Color: White. D. Folding Shower Seat: FSS on drawings (Ref. drawings for quantity, lengths and locations): 1. Manufacturers: Subject to compliance with requirements, provide products by the following: 2. Basis-of-Design Product: Subject to compliance with requirements, provide Bobrick, Reversible Solid Phenolic Folding Shower Seat, B-5181 or comparable product by one of the following: 3. Configuration: L-shaped seat, designed for wheelchair access. TOILET, BATH, AND LAUNDRY ACCESSORIES

8 4. Seat: Solid Phenolic with matte finish, antique white-colored surfaces and black phenolic resin core of slat-typeconstruction in color as selected by Architect. 5. Mounting Mechanism: Stainless steel, No. 4 finish (satin). 6. Dimensions: <33"x22-5/16">. 7. Mounting Height: 17" to top of seat (when folded down) E. Robe Hook : RH on drawings (Ref. drawings for quantity and locations) : 1. Manufacturers: Subject to compliance with requirements, provide products by the following: 2. Basis-of-Design Product: Subject to compliance with requirements, provide Bobrick, Surfaces Mounted Robe Hook, B6827 or comparable product by one of the following: 3. Description: Single-prong unit. 4. Material and Finish: Stainless steel, No. 4 finish (satin). 5. Mounting height: 38" above finished floor to top of wall plate 2.4 PRIVATE-USE BATHROOM ACCESSORIES A. Towel Shelf: S on drawings (Ref. drawings for quantity and locations, designated as S on drawings): 1. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 2. Basis-of-Design Product: Subject to compliance with requirements, provide Bobrick Stainless Steel Shelf, B-295x16 or comparable product by one of the following: 3. Description: Surface-mounted, guest-towel shelf with four 3/16" dia.holes 3 stainlesssteel tubes mounted in support arms. 4. Length: 16 inches. 5. Material and Finish: 18 guage stainless steel with satin finish. 2.5 WARM-AIR DRYERS A. Source Limitations: Obtain warm-air dryers from single source from single manufacturer. B. High-Speed Warm-Air Dryer (Ref. drawings for quantity and locations): 1. Manufacturers: Subject to compliance with requirements, provide products by the following: 2. Basis-of-Design Product: Subject to compliance with requirements, provide XLERATOR XL- GR or comparable product by one of the following: a. Excel Dryer Inc. TOILET, BATH, AND LAUNDRY ACCESSORIES

9 3. Description: High-speed, warm-air hand dryer for rapid hand drying. 4. Mounting: Surface mounted. 5. Operation: Electronic-sensor activated with operation time of 10 to 20 seconds. 6. Cover Material and Finish: Die cast zinc alloy with epoxy textured paint. 7. Electrical Requirements: V. 8. Mounting Height: 37" from floor to bottom of dyer for ADA 2.6 EMATERIALS A. Galvanized-Steel Sheet: ASTM A 653/A 653M, with G60 hot-dip zinc coating. B. Galvanized-Steel Mounting Devices: ASTM A 153/A 153M, hot-dip galvanized after fabrication. C. Fasteners: Screws, bolts, and other devices of same material as accessory unit and tamper-andtheft resistant where exposed, and of galvanized steel where concealed. 2.7 FABRICATION A. General: Fabricate units with tight seams and joints, and exposed edges rolled. Hang doors and access panels with full-length, continuous hinges. Equip units for concealed anchorage and with corrosion-resistant backing plates. B. Keys: Provide universal keys for internal access to accessories for servicing and resupplying. Provide minimum of six keys to Owner's representative. PART 3 - EXECUTION 3.1 INSTALLATION A. Install accessories according to manufacturers' written instructions, using fasteners appropriate to substrate indicated and recommended by unit manufacturer. Install units level, plumb, and firmly anchored in locations and at heights indicated. 3.2 ADJUSTING AND CLEANING A. Adjust accessories for unencumbered, smooth operation. Replace damaged or defective items. B. Remove temporary labels and protective coatings. C. Clean and polish exposed surfaces according to manufacturer's written instructions. END OF SECTION TOILET, BATH, AND LAUNDRY ACCESSORIES

10 This Page Left Intentionally Blank