Application Instructions and Code Approvals

Transcription

1 Application Instructions and Code Approvals

2 A Valuable Component to Your Roof System The addition of Invinsa Roof Board to a single ply or SBS roof system increases the roof s resistance to damage from various sources, including but not limited to hail, foot traffic, construction loads and normal roof maintenance. Invinsa is engineered as an integral part of the roof system, providing a protective layer for the insulation below and working with the membrane above to improve performance. Invinsa may be specified for new, re-roof and re-cover applications. Product Advantages High resistance to indentation, compression and crushing during installation of the roof system and during periodic maintenance, once the roof is completed Rigidity to support the roof membrane Increased resistance to moisture absorption Dimensional stability Compatibility with PVC, TPO, EPDM and SBS roofing systems UL, FM Global and other important building agency approvals Single Ply Systems Single Ply Fully Adhered Systems Invinsa Roof Board, New Construction and Re-Roof SBS Self-Adhering Base Ply Systems JM PVC with DuPont Elvaloy KEE, JM TPO or JM EPDM, Fully Adhered Invinsa Roof Board, JM PVC with DuPont Elvaloy KEE or JM TPO Invinsa Roof Board, JMCleanBond Base Sheet JMCleanBond Cap Sheet TopGard Base Coat and TopGard 5000 Reflective Coating (Optional) New Construction and Re-Roof New Construction and Re-Roof SBS Cold Adhesive Applied Various Roof Systems Invinsa Roof Board JM Two-Part Urethane Insulation Adhesive DynaBase Base Sheet DynaGlas FR CR Cap Sheet Invinsa Roof Board JM PVC with DuPont Elvaloy KEE, JM TPO or JM EPDM Roofing Membrane Cold Application Adhesive 18 to 22 Gauge Existing Built-Up Roof Existing Modified Bitumen Roof Existing Single Ply Roof New Construction and Re-Roof 1

3 In fully adhered, mechanically fastened and self-adhering SBS systems, Invinsa Roof Board protects the insulation and works with the membrane to enhance the total system properties. Patterns for Mechanical Fastening 3 5 /Board 8 /Board 8 /Board " 5 /Board 18" 12 /Board 16 /Board (1 per 2 ft 2 ) Adhesive Patterns for Fully Adhering Invinsa Roof Board To adhere to using Urethane Insulation Adhesive, JM Two-Part Urethane Insulation Adhesive, JM Green Two-Part Urethane Insulation Adhesive and other adhesives. 1. Apply adhesive to the ENRGY 3 layer and set Invinsa on top of adhesive pattern. 2. Follow instructions on respective adhesives with regard to application rates, open times, setting times and board weighting. 3. All ENRGY 3 boards run parallel to the 8' edge of a 4' x 8' Invinsa board with a 2' offset. Note: For detailed information about perimeter and corner installation, please refer the fastening pattern UA-12 available on the JM Roofing Web site or in current JM Commercial/Industrial Roof Systems Manuals. 4' x 8' Boards (with 4' offset) 4' x 8' Invinsa Roof Boards (with 2' offset to ENRGY 3) 2

4 Standard Adhesive Pattern For all adhered Invinsa systems. Adhesive Pattern Under 4' x 8' Invinsa Roof Board Adhesive Ribbons Set on Centers 4' x 8' Heavy-Duty Adhesive Pattern For systems in which membrane wrinkling is a concern, including high deck non-uniformity and self-adhering membranes. 3" Adhesive Pattern Under Two 4' x 8' Invinsa Roof Boards 4" 3" 5" Edge Ribbons Set on Centers 4" 3" Adhesive Ribbons Set on Centers Note: For detailed information about perimeter and corner installation, please refer the fastening pattern UA-12 available on the JM Roofing Web site or in current JM Commercial/Industrial Roof Systems Manuals. 3

5 FM Global Approvals JM TPO Systems FM Rating Application Standing Seam 1A-105 1A-120 1A-135 1A-210 Max. Slope in./ft (mm/m) 0.5" (13 mm) Attachment Attachment Rate Attachment Rate UF/UF 5/board XHL/XHL 7.5' (2.29 m) - (31 cm) o.c /board - 1 per 5.33 ft 2 (0.5 m 2 ) UF/UF ft 2 (0.37 m 2 ) 0.5" (13 mm) (125) LL ' (1.52 m) - (15 cm) o.c. 0.5" (13 mm) /board 10' (3.05 m) - (15 cm) o.c XHL/XHL 7.5' (2.29 m) - (31 cm) o.c /board - 1 per 5.33 ft 2 (0.5 m 2 ) ' (3.05 m) - (15 cm) o.c ' (1.52 m) - (31 cm) o.c. 0.5" (13 mm) UF/UF 5/board HL/HL 7.5' (2.29 m) - (15 cm) o.c. 0.5" (13 mm) ' (1.52 m) - 18" (46 cm) o.c PF/RR 10' (3.05 m) - (15 cm) o.c UF/UF 5/board PF/XHL ' (1.52 m) - (31 cm) o.c. 1A-135 PF/RR A-165 PF/HL ' (1.52 m) - (15 cm) o.c. 1A-240 PF/RR NC A-135 FM Rating Application 1A-60 1A ft 2 (0.37 m 2 ) UF/UF 5/board 5' (1.52 m) - (15 cm) o.c FM Global Approvals JM TPO Systems Fully Adhered Adhesives = UIA = BA = CAA = PCA = G = Max. Slope in./ft (mm/m) 0.25 (21) 0.25 (21) 0.25 (21) 0.25 (21) JM Two-Part Urethane Insulation Adhesive JM Urethane Insulation Adhesive MBR Bonding Adhesive Cold Application Adhesive Premium Cold Application Adhesive JM Green Two-Part Urethane Insulation Adhesive LL UF/UF UF/UF and Plates UF = UltraFast HL = High Load PBS = Polymer Batten Strips XHL = Extra High Load AP = All Purpose PF = Purlin Fastener RR = RhinoPlate 4 ft 2 (0.37 m 2 ) ¾" (19 (31 cm) o.c. 16/board - 1 per ¾" (19 (31 cm) o.c. SB WB SB WB 1.67 gal/100 ft gal/100 ft 2 (3.37 l/m 2 ) 1.67 gal/100 ft gal/100 ft 2 (3.37 l/m 2 ) LVOC 1.67 gal/100 ft SB WB SB WB 0.84 gal/100 ft 2 (3.37 l/m 2 ) 1.67 gal/100 ft gal/100 ft 2 (3.37 l/m 2 ) Membrane Adesives SB = JM TPO Membrane Adhesive (Solvent Based) WB = JM TPO Membrane Adhesive (Water Based) LVOC = JM TPO Membrane Adhesive (Low VOC) Insulation and Cover Boards LL = Loose Laid

6 FM Global Approvals JM PVC Systems FM Rating Application Standing Seam 1A-75 1A-105 1A-135 1A-210 NC A-135 Max. Slope in./ft (mm/m) 5' (1.52 m) - 18" " (13 mm) UF/UF 5/board (46 cm) o.c ' (3.05 m) (15 cm) o.c /board - 1 per 5.33 ft 2 (0.5 m 2 ) " (13 mm) UF/UF 5/board 6/board - 1 per 5.33 ft 2 (0.5 m 2 ) 10' (3.05 m) (15 cm) o.c ' (1.52 m) UF/UF 5/board 0.5" (13 mm) (31 cm) o.c " (13 mm) 4 ft 2 (0.37 m 2 ) (83) LL 5' (1.52 m) UF/UF 5/board 0.5" (13 mm) (15 cm) o.c ft 2 (0.37 m 2 ) ' (1.52 m) - (15 cm) o.c PF/RR 5' (1.52 m) - 18" PF/HL (46 cm) o.c ' (3.05 m) rows UF/UF 5/board (15 cm) o.c A-105 PF/HL 5' (1.52 m) A-135 PF/RR (31 cm) o.c A-150 PF/HL 5' (1.52 m) A-240 PF/RR (15 cm) o.c Adhesives = UIA = BA = CAA = PCA = G = JM Two-Part Urethane Insulation Adhesive JM Urethane Insulation Adhesive MBR Bonding Adhesive Cold Application Adhesive Premium Cold Application Adhesive JM Green Two-Part Urethane Insulation Adhesive and Plates UF = UltraFast HL = High Load PBS = Polymer Batten Strips XHL = Extra High Load AP = All Purpose PF = Purlin Fastener RR = RhinoPlate Insulation and Cover Boards LL = Loose Laid 5

7 FM Global Approvals JM PVC Systems Fully Adhered FM Rating Application Slope NC A-90 NC A-225 LL UF/UF 2" (51 mm) UF/UF 4 ft 2 (0.37 m 2 ) LL AP/UF 16/board - 1 per (31 cm) o.c. 16/board - 1 per LVOC 1.67 gal/100 ft (83) " (51 mm) AP/UF 4 ft 2 (0.37 m 2 ) (31 cm) o.c gal/100 ft (31 cm) o.c. WB (2.68 l/m 2 ) / UIA UIA, BA LVOC 1.67 gal/100 ft gal/100 ft BA (6.01 l/m 2 ) FM Global Approvals JM PVC Fleece-Backed Systems Fully Adhered FM Rating Application Slope 1A " (13 mm) UF/UF 16/board - 1 per LL LVOC 1.67 gal/100 ft 2 (8.15 l/m 2 ) NC A-90 1 (83) AP/UF WB 2 gal/100 ft 2 (8.15 l/m 2 ) / (31 cm) o.c. (31 cm) o.c. LVOC 1.67 gal/100 ft FM Global Approvals JM EPDM Systems Fully Adhered FM Rating Application Slope 1A-75 NC A-165 Adhesives = UIA = BA = CAA = PCA = G = JM Two-Part Urethane Insulation Adhesive JM Urethane Insulation Adhesive MBR Bonding Adhesive Cold Application Adhesive Premium Cold Application Adhesive JM Green Two-Part Urethane Insulation Adhesive and Plates UF = UltraFast HL = High Load PBS = Polymer Batten Strips XHL = Extra High Load AP = All Purpose PF = Purlin Fastener RR = RhinoPlate Insulation and Cover Boards LL = Loose Laid Membrane Adesives SB = JM EPDM Bonding Cement (Solvent Based) WB = JM PVC Membrane Adhesive (Water Based) LVOC = JM PVC Membrane Adhesive (Low VOC) 1.5 (125) 16/board - 1 per LL UF/UF 1.67 gal/100 ft SB (167) BA, UIA, G G 1.5 (125) G (31 cm) o.c. (31 cm) o.c

8 FM Global Approvals JM SBS Systems Cold Adhesive Applied FM Rating Application Slope LL Attachment Attachment Rate Attachment Rate Notes UF/UF AP/UF 16/board - 1 per 2 ft 2 (0.19 m 2 ) CAA 2 gal/100 ft 2 (8.15 l/m 2 ) Ply (CAA) Ply (CAA) Ply (CAA) Ply (CAA) Ply (CAA) Ply (CAA) FM Global Approvals JM SBS Systems Self-Adhering FM Rating Application Slope Attachment Rate Attachment Rate Attachment Roof Nav 16/board - 1 per 2 ft (0.19 m 2 ) 1 (83) LL UF/UF plastic 2-Ply (HW) 32/board - 1 per 1 ft 1A-165 2" (51 mm) (0.09 m 2 ) Self-Adhering UIA UIA, BA (31 cm) o.c. 2-Ply (SA) 0.75 (63) (31 cm) o.c. UIA, NC A-225 BA 1.5 gal/100 ft 2 (6.04 l/m 2 ) ALL, 2-Ply (SA) Notes UL External Fire Resistance (UL 790) Major Approvals Invinsa Roof Board New Construction Class Max. Slope in./ft (mm/m) Insulation Membrane Attachment Method UL * 1 (83) ENRGY 3 EPDM-42 JM EPDM EPDM-43 2 (167) Fully Adhered JM PVC Fleece PVC-18 1 (83) PVC-28 JM PVC 2 (167) PVC-36 Noncombustible A Fully Adhered TPO-17 JM TPO 1 (83) ENRGY 3 (Optional) TPO-33 SBS-Hot-9 JM SBS Self-Adhering SBS-Hot-39 Fully Adhered SBS-Cold-3 Combustible JM BUR BUR-14 *UL refers to constructions (paragraph) in JM s UL 790 listing. Adhesives and Plates = JM Two-Part Urethane Insulation Adhesive UF = UltraFast UIA = JM Urethane Insulation Adhesive HL = High Load BA = MBR Bonding Adhesive PBS = Polymer Batten Strips CAA = Cold Application Adhesive XHL = Extra High Load PCA = Premium Cold Application Adhesive AP = All Purpose G = JM Green Two-Part Urethane Insulation Adhesive PF = Purlin Fastener RR = RhinoPlate Insulation and Cover Boards LL = Loose Laid Membrane Notes PVC-FB = Fleece-Backed PVC MP = Any Multi-Ply Cover (existing roof) ALL = Any Membrane Cover (existing roof) HW = Heat Weld SA = Self-Adhering SP = Any Single Ply Cover (existing roof) For more detailed application or code and approval information, please contact your JM representative or call us at (800)

9 Product Warranties Johns Manville designs roofing products that work together to provide a one-source comprehensive roofing system solution. Total roofing system guarantees are available under the JM Peak Advantage Guarantee Program. To learn more about our standard guarantee terms and conditions, visit our Web site at or talk to your local JM sales representative. JM Peak Advantage Guarantees are available only on qualified JM roofing systems containing JM roofing products. JM standard product terms and conditions will apply to include a one-year limited product warranty. Limited product warranty information is available at JM/Terms and Conditions. Peak Advantage Contractor Program To ensure quality workmanship and top-notch installation, JM offers its Peak Advantage Contractor Program. Contractors selected to participate are proven to be best of class, having lived up to the highest performance standards. These contractors have access to JM s strongest guarantees. To be assured of the best possible results on the roofing system you specify, make sure it s installed by a JM Peak Advantage contractor th St. Denver, CO (800) RS (Replaces 3-06)