Versa-Span Installation Guide

Transcription

1 TAYLOR METAL PRODUCTS Installation Guide BUTYL INJECTED SEAL (AVAILABLE) 13 4"

2

3 Flashings and Details Guide NOTESTODESIGNER/INSTALLER pg.435 VS-1 EAVE DETAIL HANDLING/STORAGE&SAFETY..pg.6 EAVEDETAIL..pg.7 OFFSET CLEAT (VOC) TRIM CLEAT (VTC) EAVE (VES) HOOKEAVEWITHGUTTERDETAIL pg.8 STANDARDRIDGEDETAIL pg.9 VENTEDRIDGEDETAIL pg.10 STANDARDVALLEYDETAIL.pg.11 ALTERNATEVALLEYDETAIL pg.12 STANDARDGABLEDETAIL pg.13 ALTERNATEGABLEDETAIL..pg.14 SIDEWALLDETAIL.pg.15 RIDGEENDCAPDETAIL.pg.16 VENTEDRIDGEENDCAPDETAIL.pg.17 ROOFPITCHTRANSITIONDETAIL pg.18 ROOFHEADDETAIL..pg.19 VENTEDROOFHEADDETAIL.pg.20 SAWCUTROOFHEADDETAIL..pg.21 BACKPAN/CRICKETISODETAIL pg.22 CURBSIDEWALLDETAIL..pg.23 CURBHEADDETAIL..pg.24 CURBBACKPAN..pg.25 PIPEPENATRATIONDETAIL1.pg.26 PIPEPENATRATIONDETAIL2.pg.27 PIPEPENETRATIONMIDPANEL pg.28 ROOFENDDAMASSEMBLY pg.29 FLASHINGSELECTION.pg

4 STRUCTURAL SNAP-LOCK Features & Benefits 14-5/8" and 18" Standard Panel Width 1-3/4" Snap Lock Seam Custom Lengths 2'0" to 300'0" Concealed Clip System - No Seaming Required Minimum Slope 2 : 12 UL 580 Class 90 Wind Uplift UL Certified for Cons No. 254, 255, 261, 303, 343, 414, 508A Structural Panel Suitable For Open Purlin System up to 4' Tested For: ASTM Structural Perforation Performance ASTM 1646 Water Infiltration ASTM 1680 Air Infiltration Available Options Flat Pan / Ribs / Striations * 12" - 24" Panel Widths Weather tightness Warranty (Contact Taylor Metal Representative for cost and requirements) Factory Injected Butyl Sealant On-site roll forming available (Contact Taylor Metal Representative) Material Specifications 24 gauge Kynar 500 Painted Steel.0236" Steel (thickness prior to painting) Per ASTM A G-90 Galvanizing 24 gauge Zincalume.0236" Steel AZ55 - Clear Acrylic Coating Per ASTM A-792 Available Options 22 gauge Kynar 500 Painted Steel.029" Steel (thickness prior to painting) Per ASTM A G-90 Galvanizing AZ50 Zincalume Per ASTM and 20 ounce Copper Per ASTM B-370 Finishes Panel is available in a wide variety of Cool baked on Kynar colors. See color chart or inquire for availability. Kynar 500 Paint System - the ultimate in exterior durability and color retention Top of the line, two-coat, 70% resin finish, applied to a 1 mil. thickness 30-year 20 commercial paint warranty paint includes: warranty 30 fading year residential paint warranty fading chalking chalking chipping chipping cracking cracking peeling peeling PANEL PROFILE *Striations reduce the appearance of oil canning

5 Flashings and Details Guide Notes to Designer/Installer Taylor Commercial Products is providing the following details as an aid in design. The details in this guide are not inclusive to all design situations. The designer/installer is responsible for modifications and should take into consideration all aspects of the project including climate conditions, such as, snow and wind, as well as, building code requirements, building design, building usage and maintenance requirements. Installation should be performed only by qualified installers familiar with metal roofing systems and industry standards. For details not shown in this guide, refer to the Sheet Metal and Air Conditioning Contractors National Association (SMACNA) architectural sheet metal manual for proper design. The Standard gauge for all products in this guide is 24 gauge and the standard finish is Kynar 500 /Hylar We recommend specifying all flashings be the same gauge, color, and finish as the panels to insure long-term durability and color match. Substrates Details in the manual are all shown over solid substrate. can be used over spaced purlins. For solid substrate, Taylor Commercial Products recommends 5/8 plywood or metal decking. Underlayments Minimum underlayment requirements are 30 lb. ASTM rated felt, a synthetic underlayment with Class A and ASTM UV protection technology or a high temperature self-adhering rubberized membrane. When choosing the underlayment, consider the roof slope, roof design, roof panel, and the climate. Drag Load Requirements All panels must be pinned at the top to resist the drag load caused by snow loads, live loads, and the weight of the panel. Drag load is a function of roof slope, actual load and length of panels. Contact Taylor Commercial Products for specific drag load requirements. 4

6 Flashings and Details Guide Ventilation/Insulation It is the responsibility of the designer to determine the material types needed to control condensation and to insulate and ventilate the roof system. Applications over rigid insulation may require blocking for solid attachment and framing the perimeter for installation of perimeter flashings. Oil Canning Flat metal surfaces will display waviness commonly referred to as oil canning. Oil canning is caused by a variety of conditions: Steel mill tolerances, variations in or uneven substrates and roofing underlayments. Oil canning is a characteristic of metal roofing, not a defect and is not a cause for rejection. Taylor Commercial Products with striations or accent ribs to help minimize oil canning. Thermal Movement The Panels and the flashings must be allowed to expand and contract, especially with longer length panels. The panel may need to have a slight gap where the panel hooks the offset cleat to allow for thermal movement of the panels. Snow Design The following details do not address all conditions for snow environments. Consult with the designers, engineers, and others for acceptable details to accommodate your project and climate conditions. When possible, gutters, valleys, pitch changes or other penetrations should be minimized in snow areas. All roof penetrations should be located as close to the ridge or top of roof. Snow country requires special designs for valleys to accommodate accumulation of snow and ice from uphill panels. Roof design should be considered in snow areas. Roof design should help resist the melting and freezing of snow and ice. A fit for purpose roof design has the greatest impact on maintaining a damage free roof system in snow areas. Please contact a Taylor Commercial Products representative for assistance in detail designs and appropriate panel selection for specific climate and building conditions. 5

7 Flashings and Details Guide Handling / Storage & Safety Handle materials with care when off-loading or moving materials to avoid damage to panels or flashings. Long panels may require two or more pick-up points, properly spaced to avoid damaging panels. Plan ahead; contact Taylor Commercial Products for recommendations on handling/hoisting long panels. Store the panels, flashings and accessories in a dry, well ventilated area, off the ground. If covering, allow ventilation around panels. Elevate one end of bundle to allow drainage of wet materials. Wear clean, soft-soled shoes when walking on roofing panels to avoid damage to the painted finish. Take care that sand, gravel, dirt, etc. sticking to your shoes is not carried onto the roof, scratching or otherwise damaging the finish on the roofing material. Walking on asphalt impregnated felt paper, especially on a hot day, can cause the asphalt to stick to your shoes and be tracked on to the roofing material. Take care when painting to avoid getting over spray on the roofing material. Remember that wind can carry paint particles some distance. Over spray can cause the finish of the roofing material to look dull and may void your warranty. Secure materials, especially when leaving the site, on the ground or roof to prevent winds from moving the materials. Wind-blown materials may cause damage to the material, property or persons. Always use proper safety equipment and attire to minimize risk of cuts or other injuries. Do not walk on panels that have not been completely installed. Do not walk on major ribs of panels. Metal roofs that are wet or dusty can be extremely slippery. Wear soft soled shoes and a safety harness to minimize risk of falling. Avoid installing metal panels in windy conditions. Safety considerations are the responsibility of the installer and his crew. Be sure to use common sense and generally accepted safety practices when installing roofing materials. 6

8 Flashing and Details Guide EAVE HOOK (VEH) HOOK EAVE EAVE HOOK (VEH) EAVE STANDARD (VEH) EAVE HOOK (VSEH) EAVE STANDARD (VSES) 7

9 HOOK VS-1 EAVE WITH DETAIL GUTTER Flashings and Details Guide BOX GUTTER (VBG) (VSBG) OFFSET CLEAT (VOC) TRIM CLEAT (VTC) EAVE (VES) 5 8

10 Flashing and Details Guide RIDGE STANDARD (VRS) STANDARD RIDGE 3 RIDGE (VSRS) 9

11 Flashing and Details Guide VENTED RIDGE (VRFV) VENTED RIDGE 3 VENTED RIDGE (VSRFV) 10

12 Flashing and Details Guide 6 OFFSET CLEAT (VOC) VALLEY FLASHING (VVF) STANDARD VALLEY 3 6 VALLEY FLASHING (VSVF) 11

13 Flashing and Details Guide 6 VALLEY FLASHING (VVF) ALTERNATE VALLEY 3 6 VALLEY FLASHING (VSVF) 12

14 $ $ Flashing and Details Guide STANDARD GABLE GABLE STANDARD GABLE (VGS) SUPPORT FLASHING (VSF) STANDARD'GABLE'(VSGS1) STANDARD$GABLE$(VGS)$ Standard Gable (VSGS1) SUPPORT FLASHING (VSF) (VGS) $ Color ALT'L'CLOSURE'(VSLF) ALT$L$CLOSURE$(VAGL)$ $$$$$$$$$$$$$$$$$NEOPRENE$WASHERED$SCREW$12 $OC Color CURB$SIDE$(VCS) CURB'SIDEWALL'(VSSWC) CURB SIDEWALL Color 13 GABLE'SUPPORT'(VSGSF) GABLE$SUPPORT$(VGC)$ BACK'PAN'(VSPAN) BACK$PAN$(VPAN)$ Color END'DAM'(VSED) END$DAM$ Varies per pa

15 OFFSET CLEAT (VOC) SUPPORT FLASHING (VSF) MS200 Flashing and Details Guide and Details Guide Flashings VS-1 EAVE DETAIL ALTERNATE GABLE TRIM CLEAT (VTC) ALT CLOSURE L CLOSURE(VSLF) (VAGL) EAVE (VES) ALT GABLE GABLE (VSGS2) ALT (VAGS) 5 14 Taylor Metal Products - Phone: or or ~ Fax: ~ 14 Taylor Metal Products - Phone: ~ Fax: ~ 15

16 VS-1 SIDE EAVE DETAIL WALL Flashings and Details Guide OFFSET CLEAT (VOC) TRIM CLEAT (VTC) EAVE (VES) SUPPORT FLASHING (VSF) SIDE WALL (VSW) (VSSW) 5 15

17 Flashing and Details Guide RIDGE END CAP (VREC) RIDGE END CAP RIDGE END CAP (VREC) 3 RIDGE END CAP (VSREC) 16

18 VENTED RIDGE END CAP VS-1 EAVE DETAIL Flashings and Details Guide OFFSET CLEAT (VOC) TRIM CLEAT (VTC) EAVE (VES) VENTED RIDGE END CAP (VVREC) VENTED ENDWALL (VEWV) VENTED RIDGE END (VSRECV) 5 17

19 Flashing and Details Guide ENDWALL (VEW) ROOF PITCH TRANSITION ENDWALL (VEW) ENDWALL (VSEW) 18

20 Flashing and Details Guide END WALL ENDWALL (VEW) 3 ENDWALL (VSEW) 19

21 VENTED END WALL VENTED ENDWALL (VEWV) (VSWV) 20 Flashing and Details Guide

22 ENDWALL (VEW) (VSRF) SAW CUT ROOF HEAD 3 21 Flashing and Details Guide REGLET (VSRF) (VRF)

23 OFFSET CLEAT (VOC) Flashings and Details Guide BACK PAN VS-1 EAVE DETAIL TAB SIDE WALL TO RECEIVE BACK PAN TRIM CLEAT (VTC) EAVE (VES) BACK PAN (VSPAN) PAN FLASHING FLASHING(VPAN) (VPAN) PAN TAB SIDE WALL TO RECEIVE BACK PAN 5 22

24 CURB SIDE WALL TURNSIDEOFPANELUP 23 CURB CURB SIDEWALL (VSSWC) (VCS) Flashing and Details Guide

25 VS-1 CURB EAVE HEAD DETAIL Flashings and Details Guide OFFSET CLEAT (VOC) TRIM CLEAT (VTC) EAVE (VES) CURB CURB HEAD (VSCH) (VCD) 5 24

26 Flashing and Details Guide CURB PAN/CRICKET 25

27 Flashing and Details Guide PIPE PENETRATION 26

28 Flashing and Details Guide PIPE PENETRATION 27

29 VS-1 PIPE EAVE PENETRATION DETAIL Flashings and Details Guide OFFSET CLEAT (VOC) TRIM CLEAT (VTC) EAVE (VES) 5 28

30 Flashing and Details Guide END DAM NOTESTODESIGNER/INSTALLER pg.233 HANDLING/STORAGE&SAFETY..pg.4 EAVEDETAIL..pg.5 OFFSET CLEAT (VOC) TRIM CLEAT (VTC) EAVE (VES) HOOKEAVEWITHGUTTERDETAIL pg.6 STANDARDRIDGEDETAIL pg.7 HOOKRIDGEDETAIL pg.8 VENTEDRIDGEDETAIL pg.9 STANDARDVALLEYDETAIL.pg.10 ALTERNATEVALLEYDETAIL pg.11 STANDARDGABLEDETAIL pg.12 ALTERNATEGABLEDETAIL..pg.13 RADIUSGABLEDETAIL pg.14 SIDEWALLDETAIL.pg.15 RIDGEENDCAPDETAIL.pg.16 VENTEDRIDGEENDCAPDETAIL.pg.17 ROOFPITCHTRANSITIONDETAIL pg.18 ROOFHEADDETAIL..pg.19 VENTEDROOFHEADDETAIL.pg.20 SAWCUTROOFHEADDETAIL..pg.21 BACKPAN/CRICKETISODETAIL pg.22 CURBSIDEWALLDETAIL..pg.23 CURBHEADDETAIL..pg.24 PIPEPENATRATIONDETAIL1.pg.25 PIPEPENATRATIONDETAIL2.pg.26 ROOFENDDAMASSEMBLY pg.27 FLASHINGSELECTION.pg

31 Versa Span Flashings Versa Span Flashings are 10' TAYLOR METAL PRODUCTS EAVE STANDARD ( VSES ) IF PAINTED, THIS SIDE EAVE HOOK ( VSEH ) IF PAINTED, THIS SIDE OFFSET CLEAT ( VSOC ) 3 3 8" 4 3 8" SPECIFY PITCH SPECIFY PITCH 1 2 " 1 1 2" 1 1 2" 1 1 2" 5 8 " 5 8 " 1 2 " 1 2 " SCALE 1:2 S.O. 6" WEIGHT: 4.9 LBS. SCALE 1:2 S.O. 8" WEIGHT: 6.5 LBS. SCALE 1:2 S.O. 3" WEIGHT: 2.5 LBS. BOX GUTTER ( VSBG ) SUPPORT FLASHING ( VSSF ) GABLE STANDARD ( VSGS ) 1 3 4" 1 1 2" 1 2 " 1 2 " 5 1 2" 4 3 8" 3 1 4" 1 2 " 1 2 " 1 7 8" 1 8 " 3" 5 8 " 4" 1 2 " SCALE 1:3 S.O " WEIGHT: 13.3 LBS. SCALE 1:3 S.O " WEIGHT: 6 LBS. SCALE 1:3 S.O. 9.25" WEIGHT: 7.6 LBS. ALT GABLE ( VSAG ) GABLE SUPPORT ( VSGC ) ALT L CLOSURE ( VSALC ) 2 1 2" 1 2 " 4 3 8" 4 1 4" 1 1 2" 1 2 " 5 8 " 1 2 " 1 2 " SCALE 1:3 S.O. 8.5" WEIGHT: 7 LBS. SCALE 1:3 S.O. 5.75" WEIGHT: 4.7 LBS. SCALE 1:3 S.O. 3" WEIGHT: 2.5 LBS. 30

32 Versa Span Flashings Versa Span Flashings are 10' TAYLOR METAL PRODUCTS STANDARD RIDGE ( VSRS ) RIDGE FULL VENTED ( VSRFV ) IF PAINTED, THIS SIDE 7" 7" IF PAINTED, THIS SIDE 8" SPECIFY PITCH 8" SPECIFY PITCH 1 2 " 1 1 2" 5 8 " 5 8 " 1 1 2" 1 2 " SCALE 1:4 S.O. 16" WEIGHT: 13.1 LBS. SCALE 1:5 S.O " WEIGHT: 17.4 LBS. VALLEY FLASHING ( VSVF ) ZEE CLOSURE ( VSZC ) 1 IF PAINTED, THIS SIDE SPECIFY PITCH " SCALE 1:6 S.O. 24" WEIGHT: 19.7 LBS. RIDGE END CAP ( VSREC ) SPECIFY PITCH VENTED RIDGE END ( VSRECV ) SCALE 1:3 S.O " WEIGHT: 3 LBS. SPECIFY PITCH SUPPORT CLEAT ( VSRECC / VSVRECC ) IF PAINTED, THIS SIDE 7" IF PAINTED, THIS SIDE 6" 5 3 8" 1 1 2" 5 8" 6" Vented " Standard " 1 2" 5 8" 5 8" 1 2" 1 2" 1 2 " SCALE 1:4 S.O. 14.5" WEIGHT: 11.9 LBS. SCALE 1:4 S.O " WEIGHT: 12.9 LBS. SCALE 1:3 S.O " / 6.75" WEIGHT: 6 LBS. BACK PAN ( VSPAN ) 5 1 2" S.O. 24" WEIGHT: 21.3 LBS " SCALE 1:4 31

33 Versa Span Flashings Versa Span Flashings are 10' TAYLOR METAL PRODUCTS VALLEY WIDE FLASHING ( VSVFW ) S.O. 34.5" SPECIFY PITCH IF PAINTED, THIS SIDE " " WEIGHT: 28.2 LBS. SCALE 1:5 CURB ENDWALL ( VSCH ) REGLET ( VSRF ) 1 2 " (Varies) 5" 3 5 8" 6" SCALE 1:4 S.O. 12" WEIGHT: 9.8 LBS. CURB SIDEWALL ( VSCSW ) 1 2 " SCALE 1:3 S.O " WEIGHT: 4.6 LBS. PERFORATED STRIP ( VSPS ) 4" 4" 4" 1 1 2" 1 2" SCALE 1:4 S.O. 10" WEIGHT: 8.2 LBS. ENDWALL ( VSEW ) VENTED ENDWALL ( VSEWV ) SCALE 1:2 S.O. 4" WEIGHT: 3.3 LBS. SIDE WALL ( VSSW ) 5" 4 3 8" 4 1 4" SPECIFY PITCH SPECIFY PITCH 1 3 4" 6" 5" 1 1 2" 5 8" 1 2 " 1 1 2" 1 2" SCALE 1:4 S.O. 12" WEIGHT: 9.8 LBS. SCALE 1:4 S.O. 12" WEIGHT: 10.7 LBS. SCALE 1:3 S.O. 8" WEIGHT: 6.6 LBS. 32

34 Versa Span Flashings Versa Span Flashings are 10' TAYLOR METAL PRODUCTS VERSA-SPAN END DAM 1 5 8" " *END DAM IS EXAMPLE ONLY. SEE SPECIFIC END DAM DETAIL SHEET FOR DIMENSIONS (SEPARATE FORM) " S.O. VARIES 2" WEIGHT: VARIES SCALE 1:8 33

35 Custom Trim Order Customer Name: Job Name: Drawing #: Pitch: # of Pieces: Description: Hems: Open Closed Slightly Open Drawing #: Pitch: # of Pieces: Description: Hems: Open Closed Slightly Open Drawing #: Pitch: # of Pieces: Description: Hems: Open Closed Slightly Open Drawing #: Pitch: # of Pieces: Description: Hems: Open Closed Slightly Open Please provide a drawing for each flashing with precise measurements and angles Fax to: Ridge Dr NE Salem OR Phone: or

36 Fax to: Order Form New Order Add-on Order PO# Date: Inside Sales: Sold To: Job Name: Ship To: Order Contact: Phone # Fax # Will Call Delivery Date: Panels with need Pattern Choice * Color: 12" Easy-Lock* Shadow Line* 16" Easy-Lock* Soffit* 16" StreamLine* Smoothwall* Pattern Choices: T-3 Flat Striations Tuff Rib Ribs Notched? Y N Panel & Flashing Items Marion R Panel HR-34 GR7 GR5 PBR 12-3/4" MS150* 2-1/2" Corrugated 16-5/8" MS150* Classic 7/8" Corrugated 14-5/8"MS200* Pattern Choices: Ribs Flat Pitch: Striations Gauge Clip Relief? Y N Sealant? Y N Notched? Y N 14-5/8" Versa Span* 18" Versa Span* 18" MS200* *All Kynar, Easy-Lock, Soffit, & Smoothwall, Clip Lock, MS150, Versa Span, MS200 flashings are 10' *All Armor Tech 26 and 29 Gauge. StreamLine, T-3, Tuff Rib, GR7, PBR, Corrugated, & GR5 flashings are 12'6" Quantity Length Item Description Quantity Length Item Description Forgetting Anything? Underlayment? Screws? Clips? Caulking? Closures? 4566 Ridge Dr NE Salem, OR F: P

37

38

39

40 TAYLOR METAL PRODUCTS QUALITY PRODUCTS EXCEPTIONAL SERVICE SALEM BRANCH 4566 Ridge Drive NE Salem, OR Office: Toll Free: Fax: MCCLELLAN BRANCH 5711 Perrin Ave McClellan, CA Office: Toll Free: Fax: WOODINVILLE BRANCH th St. SE Woodinville, WA Office: Toll Free: Fax: AUBURN BRANCH 710 A St. NW Suite 101 Auburn, WA Office: Toll Free: Fax: RIVERSIDE BRANCH 4880 Felspar St. Riverside, CA Office: Toll Free: Installation Guide Taylor Metal Products