Polimar FCS Sealer Coat

Transcription

1 Polimar FCS Sealer Coat Product Data Sheet May 2014 Polimar FCS Sealer Coat is used as a topcoat or sealer layer for Polimar FCS systems. Description Polimar FCS Sealer Coat is a high-grade, mechanically durable finish that can be supplied in any colour and can even be used for creating patterns or lettering. Different toppings can be incorporated into the system to achieve the desired slip-resistant properties. Material A two-component, fast-reactive, flexibilised, pigmented and filled PMMA-based (polymethyl methacrylate) sealing resin. Features and Benefits Available in most RAL colours Can be used in any colour to create desired patterns (e.g. tiled look, lettering) Toppings (deco chips, quartz sand) can be incorporated into the system to create the desired slip resistant properties Abrasion-resistant Permanently weather-resistant (UV-, hydrolysis- and alkali-resistant) Easy and fast application Fast-curing Solvent-free Areas of Application Polimar FCS Sealer Coat is used as a finish on most Polimar FCS systems. The surfaces of the system can be designed in any colour and pattern. The appropriate slip resistant properties are achieved by using the appropriate wear layer or surfacing depending on the application and specification for each project. Packaging kg Polimar FCS Sealer Coat Must be mixed with 2 bags of Polimar FCS Catalyst Colours Polimar FCS Sealer Coat is available in the following standard colours: RAL 7030 Mid grey RAL 7032 Light grey RAL 7043 Dark grey Other RAL colours are available on request. Storage Store products sealed in their original airtight container and in a cool, dry and frost-free place. Unopened products have a shelf life of at least 6 months. Direct sunlight on the containers should be avoided, including on site. After removing some of the contents, reseal the containers so they are airtight. Application conditions Temperature Product Temperature range, in C Air Substrate* Material Polimar FCS Sealer Coat -5 to to +40* +3 to +30 * The substrate temperature must be at least 3 C above the dew point during application and curing.

2 Moisture The relative humidity must be 90 %. The surface to be coated must be dry and ice-free. The surface must be protected from moisture until the coating has hardened. Reaction times Polimar FCS Sealer Coat (at 20 C, 2 % catalyst) Pot life: approx. 15 minutes Rain-proof after: approx. 45 minutes Can be walked on / overcoated after: approx. 60 minutes Curing time approx. 3 hours Higher temperatures or greater proportions of catalyst will reduce reaction times, while lower temperatures and smaller proportions of catalyst will increase reaction times. Consumption rates Approx. 0.5 kg/m 2 over smooth and aggregated areas Technical data Density: 1.04 to 1.20 g/cm³ Product Application Application equipment / tools For mixing the product: Twin-paddle stirrer Cleaning For applying the product: Finishing roller (sheepskin roller, minimal shedding) Rubber blade, hard (for applying finish to topped surfaces) Substrate preparation Polimar FCS Sealer Coat can be applied to hardened primer, waterproofing or to the self-levelling mortar, depending on the specification. Polimar FCS Sealer Coat must be used as a topcoat on Polimar FCS Wear Course. Mixing First stir the tub contents thoroughly. Then add Polimar FCS Catalyst (2 bags) while stirring the resin at the slow-speed setting and mix for 2 minutes. Make sure that the product on the base and sides of the container is mixed in. At product temperatures < 10 C the product should be stirred for 4 minutes, as the catalyst will take longer to dissolve. Application Use the finish roller to apply an even layer of the mixed material (approx. 0.5 kg/m2). Avoid fluctuating layer thicknesses. Finish Design Options Finish design using Polimar FCS Deco Chips (suitable for low ultilised areas such as balconies where enhanced slip resistance is required use aggregated wear or surfacing layers depending on specification) Use a hopper gun to apply Polimar FCS Deco Chips to the freshly applied finish while it is still wet. A maximum of 50 g/m2 can be applied, depending on the look you want to achieve. There should not be any excess chips (surface completely covered with chips) at any point. If work is interrupted or when it is completed, clean the tools thoroughly with Polimar Acetone Cleaner within the pot life of the material (approx. 10 minutes). This can be done with a brush. Do not use the tools again until the

3 Acetone Cleaner has evaporated fully. Simply immersing the tools in the Acetone Cleaner will not prevent the material from hardening. Safety Information Please refer to the safety data sheets for the products used. General Information The above information, especially information about application of the products, is based on extensive development work as well as many years of experience and is provided to the best of our knowledge. However, the wide variety of requirements and conditions on site mean that it is necessary for the product to be tested to ensure that it is suitable for the intended purpose. Only the most recent version of the document is valid. We reserve the right to make changes to reflect advances in technology or improvements to our products. IKO PLC Literature Enquiries Tel: Website: Sales Support Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB Tel: Fax: Technical & Design Services Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB Tel: Fax: Whilst every care is taken to see that the information given in this literature is correct and up to date it is not intended to form part of any contract or give rise to any collateral liability, which is hereby specifically excluded. Intending purchasers of our materials should therefore verify with the company whether any changes in our specification or application details or otherwise have taken place since this literature was issued. Company Registered in England No Registered Office: Appley Lane North, Appley Bridge, Wigan, Lancashire, WN6 9AB

4 Polimar FCS Waterproofing & Detailing Product Data Sheet May 2014 Two-component, fast-reactive and highly flexible PMMA-based (polymethyl methacrylate) waterproofing resins Description Polimar FCS Waterproofing & Detailing are high-grade, PMMA-based waterproofing resins with low-temperature flexibility and are used to provide durable reinforced waterproofing in areas such as roofing, balconies, walkways and car parks as part of the Polimar FCS Systems. Liquid application allows seamless waterproofing systems to be applied to large areas, and even the most complex roof penetrations and details to be securely incorporated. Features and Benefits Highly flexible and crack-bridging even at extreme sub-zero temperatures Permanently weather-resistant (UV-, hydrolysis- and alkali-resistant) Fully bonded to the substrate, therefore no flow paths for water under the membrane Easy and fast application The most complex roof penetrations can be securely incorporated in the seamless waterproofing system Fast-curing Can also be applied at sub-zero temperatures Can be applied to almost all substrates, including variable substrates (when combined with Polimar FCS Primers) Solvent-free Test certificates and technical approvals (ETA, AbP) for the areas of roof waterproofing and the waterproofing of joints on water-impermeable concrete units Areas of Application Polimar FCS Waterproofing is applied together with Polimar FCS Fleece reinforcement for waterproofing large areas and details on roofs, balconies, walkways and car parks. For utilised areas such as balconies, walkways and car parks Polimar FCS Waterproofing is applied in conjunction with Polimar FCS wearing and surfacing layers depending on the application and specification for each particular project. Polimar FCS Detailing is a variant of Polimar FCS Waterproofing that is more viscous / thixotropic to reduce runoff when applied to sloping and vertical surfaces. It is therefore used primarily for the waterproofing of details. Product Details kg Polimar FCS Waterproofing / Detailing Must be mixed with 2 bags of Polimar FCS Catalyst Storage Store products sealed in their original airtight container and in a cool, dry and frost-free place. Unopened products have a shelf life of at least 6 months. Direct sunlight on the containers should be avoided, including on site. After removing some of the contents, reseal the containers so they are airtight.

5 Application conditions Product Temperature range, in C Air Substrate* Material Polimar FCS Waterproofing -5 to to +50* +3 to +30 Polimar FCS Detailing -5 to to +50* +3 to +30 * The substrate temperature must be at least 3 C above the dew point during application and curing. The substrate temperature must not be less than +3 C if a topping is applied to the surface. Reaction problems can occur at lower temperatures. Moisture The relative humidity must be 90 %. The surface to be coated must be dry and ice-free. The surface must be protected from moisture until the coating has hardened. Reaction times Polimar FCS Waterproofing / Polimar FCS Detailing (at 20 C, 2 % catalyst) Pot life: approx. 15 minutes Rain-proof after: approx. 30 minutes Can be walked on / overcoated after: approx. 1 hour Curing time approx. 3 hours Higher temperatures or greater proportions of catalyst will reduce reaction times, while lower temperatures and smaller proportions of catalyst will increase reaction times. Consumption rates Waterproofing layer reinfotced with Polimar FCS Fleece: approx kg/m² Technical data Density: 1.22 g/cm³ Water vapour diffusion resistance factor: 8150 [-] Product Application Application equipment / tools For mixing the product: Twin-paddle stirrer For applying the product: Sheepskin roller Brush (only for areas not accessible with the sheepskin roller) Substrate to be coated Apply the waterproofing resin to the cured Polimar FCS Primer or suitably prepared substrate. Mixing First stir the tub contents thoroughly. Then add Polimar FCS Catalyst (2 bags) while stirring the resin at the slow-speed setting and mix for 2 minutes. Make sure that the product on the base and sides of the container is mixed in. At product temperatures < 10 C the product should be stirred for 5 minutes, as the catalyst will take longer to dissolve. Application Use Polimar FCS Waterproofing for waterproofing horizontal areas, Polimar FCS Detailing is used for vertical surfaces (e.g. upstands on details). Apply a generous and even layer of the mixed material to the entire area (at least 1.5 kg/m 2 ), then immediately embed Polimar FCS Fleece, using the roller to smooth out and remove any trapped air bubbles and creases. Immediately apply further material (wet on wet) on top of the fleece up to the required coverage rate. Fleece overlaps must be a minimum of 50mm.

6 Preparation for subsequent layers such as bonded tiles or loose-laid surfacing a) Fully bonded surfacing (e.g. tiles) Once the waterproofing has cured, apply an additional covering layer of Polimar FCS Waterproofing (approx. 1.5 kg/m2) and top with a generous amount of sand while still wet (quartz sand mm). Vacuum off the excess/loose sand after the surface has hardened. The topping gives the surface the necessary roughness that allows the subsequent surfacing supplied by others to be bonded onto the base. Never apply the topping to the waterproofing layer. Only use dry quartz sand. b) Loose-laid surfacing (e.g. stone slabs) Once the waterproofing has cured, apply an additional covering layer of Polimar FCS Waterproofing (approx. 1.5 kg/m2). This protects the waterproofing layer against the mechanical loads of the surfacing supplied by others. Cleaning If work is interrupted or when it is completed, clean the tools thoroughly with Polimar Acetone Cleaner within the pot life of the material (approx. 10 minutes). This can be done with a brush. Do not use the tools again until the Acetone Cleaner has evaporated fully. Simply immersing the tools in the Acetone Cleaner will not prevent the material from hardening. Safety Information Please refer to the safety data sheets for the products used. General Information The above information, especially information about application of the products, is based on extensive development work as well as many years of experience and is provided to the best of our knowledge. However, the wide variety of requirements and conditions on site mean that it is necessary for the product to be tested to ensure that it is suitable for the intended purpose. Only the most recent version of the document is valid. We reserve the right to make changes to reflect advances in technology or improvements to our products. IKO PLC Literature Enquiries Tel: marketing@ikogroup.co.uk Website: Sales Support Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB Tel: Fax: sales@ikogroup.co.uk Technical & Design Services Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB Tel: Fax: technical@ikogroup.co.uk

7 Polimar FCS Low Odour Waterproofing Product Data Sheet May 2014 High-grade, highly flexible low-odour PMMA-based waterproofing resin for Polimar FCS systems. Description Polimar FCS Low Odour Waterproofing is a high-grade, highly flexible, low-odour PMMA-based waterproofing resin for Polimar FCS systems. It is used for the durable and reliable waterproofing of buildings. Depending on crack-bridging requirements, it can be applied either with or without fleece reinforcement. Due to its low-odour properties during application, this waterproofing product is also suitable for odour-sensitive areas. Its liquid application allows seamless waterproofing systems to be applied to large areas, and even the most complex roof penetrations and details to be securely incorporated. Features and Benefits Highly flexible and crack-bridging even at extreme sub-zero temperatures Low odour Permanently weather-resistant (UV-, hydrolysis- and alkali-resistant) Fully bonded to the substrate, therefore no flow paths for water under the membrane Easy and fast application The most complex roof penetrations can be securely incorporated in the seamless waterproofing system Fast-curing Can also be applied at sub-zero temperatures Can be applied to almost all substrates, including variable substrates (when combined with Polimar FCS Primers) Solvent-free Areas of Application Polimar FCS Low Odour Waterproofing is a product that belongs to the Polimar FCS system and is used for the waterproofing of buildings. As part of the Polimar FCS system, it serves as a highly flexible waterproofing layer and is applied either with or without fleece reinforcement, depending on the crack-bridging requirements. It is used to waterproof main areas and details on garages, bridges, balconies, terraces and access balconies. Product Details kg Polimar FCS Low Odour Waterproofing Must be mixed with 2 bags of Polimar FCS Catalyst (2 x 0.1 kg) kg Storage Store products sealed in their original airtight container and in a cool, dry and frost-free place. Unopened products have a shelf life of at least 6 months. Direct sunlight on the containers should be avoided, including on site. After removing some of the contents, reseal the containers so they are airtight. Application conditions Product Temperature range, in C Air Substrate* Material Polimar FCS Low Odour Waterproofing -5 to to +50* +5 to +30 * The substrate temperature must be at least 3 C above the dew point during application and curing.

8 Moisture The relative humidity must be 90 %. The surface to be coated must be dry and ice-free. The surface must be protected from moisture until the coating has hardened. Reaction times Polimar FCS Low Odour Waterproofing (at 20 C, 2 % catalyst) Pot life: approx. 15 minutes Rain-proof after: approx. 45 minutes Can be walked on / overcoated after: approx. 1.5 hours Curing time approx. 3 hours Higher temperatures or greater proportions of catalyst will reduce reaction times, while lower temperatures and smaller proportions of catalyst will increase reaction times. Consumption rates As flexible layer (without fleece): at least 1.60 kg/m² As reinforced layer (with fleece): at least 2.40 kg/m² As sole waterproofing with fleece: approx. 3.20kg/ m² Technical data Density: 1.56 g/cm³ Product Application Application equipment / tools For mixing the product: Twin-paddle stirrer For applying the product: a) Application without fleece Rubber squeegee with serrated edge (6mm thick, notch spacing 7mm, e.g. Polyplan notch size no.7) and Metal spiked roller b) Application with fleece Sheepskin roller Substrate to be coated Apply the waterproofing resin to the cured Polimar FCS Primer or suitably prepared substrate. Use Polimar FCS Low Odour Waterproofing for waterproofing horizontal areas. Mixing First stir the tub contents thoroughly. Then add the catalyst while stirring the resin at the slow-speed setting and mix for 2 minutes. Make sure that the product on the base and sides of the container is mixed in. At product temperatures < 10 C the product should be stirred for 5 minutes, as the catalyst will take longer to dissolve. Application Waterproofing with embedded fleece Apply a generous and even layer of the mixed material to the entire area (at least 1.8kg/ m²), then immediately embed the Polimar FCS fleece and use a sheepskin roller to remove any air bubbles. Apply the remaining material directly (wet on wet) up to the required consumption rate. In each case use a sheepskin roller to spread the material over the surface. Fleece overlaps must be at least 5cm wide. Preparation for subsequent layers None required.

9 Cleaning If work is interrupted or when it is completed, clean the tools thoroughly with Polimar Acetone Cleaner within the pot life of the material (approx. 10 minutes). This can be done with a brush. Do not use the tools again until the Acetone Cleaner has evaporated fully. Simply immersing the tools in the Acetone Cleaner will not prevent the material from hardening. Safety Information Please refer to the safety data sheets for the products used. General Information The above information, especially information about application of the products, is based on extensive development work as well as many years of experience and is provided to the best of our knowledge. However, the wide variety of requirements and conditions on site mean that it is necessary for the product to be tested to ensure that it is suitable for the intended purpose. Only the most recent version of the document is valid. We reserve the right to make changes to reflect advances in technology or improvements to our products. IKO PLC Literature Enquiries Tel: marketing@ikogroup.co.uk Website: Sales Support Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB Tel: Fax: sales@ikogroup.co.uk Technical & Design Services Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB Tel: Fax: technical@ikogroup.co.uk Whilst every care is taken to see that the information given in this literature is correct and up to date it is not intended to form part of any contract or give rise to any collateral liability, which is hereby specifically excluded. Intending purchasers of our materials should therefore verify with the company whether any changes in our specification or application details or otherwise have taken place since this literature was issued. Company Registered in England No Registered Office: Appley Lane North, Appley Bridge, Wigan, Lancashire, WN6 9AB

10 Polimar FCS Primer Product Data Sheet May 2014 Polimar FCS Primer is a fast-reactive, multi-purpose primer for porous, bitumen and mineral substrates such as concrete, timber, bitumen felt and asphalt. Description Polimar FCS Primer is a 2-component, fast-reactive and flexibilised PMMA-based (polymethyl methacrylate) resin primer Features and Benefits Reliable and rapid coating of porous, bitumen and mineral substrates (concrete, timber, bitumen felt, asphalt etc) Easy to apply Can also be applied at sub-zero temperatures Fast-curing Hydrolysis - and alkali-resistant Solvent-free Areas of Application Polimar FCS Primer is a multi-purpose primer for application to all areas including details and upstands. It allows absorbent substrates (concrete, screed, timber etc.) as well as asphalt substrates, bitumen coatings and polymer-bitumen sheeting to be pre-treated (primer and barrier) so that a Polimar FCS waterproofing system can be applied. Packaging 10.00kg Polimar FCS Primer Must be mixed with 2 bags of Polimar FCS Catalyst Colour Polimar FCS Primer is unpigmented. Storage Store products sealed in their original airtight container and in a cool, dry and frost-free place. Unopened products have a shelf life of at least 6 months. Direct sunlight on the containers should be avoided, including on site. After removing some of the contents, reseal the containers so they are airtight. Application conditions Product Temperature range, in C Air Substrate Material Polimar FCS Primer -5 to to +50* +3 to +30 * The substrate temperature must be at least 3 C above the dew point during application and curing. Moisture The relative humidity must be 90 %. The surface to be coated must be dry and ice-free. The surface must be protected from moisture until the coating has hardened.

11 Reaction times Polimar FCS Primer (at 20 C, 3 % catalyst) Pot life: approx. 10 minutes Rain-proof after: approx. 30 minutes Can be walked on / overcoated after: approx. 45 minutes Curing time approx. 3 hours Higher temperatures or greater proportions of catalyst will reduce reaction times, while lower temperatures and smaller proportions of catalyst will increase reaction times. Consumption rates Substrate Consumption Smooth 0.40 kg/m2 Fine-sandy 0.50 kg/m2 Rough 0.80 kg/m2 Technical data Density: 1.03 g/cm³ Product Application Application equipment / tools For mixing the product: Twin-paddle stirrer For applying the product: Sheepskin roller Brush (only for areas not accessible with the sheepskin roller) Substrate preparation The primer must only be applied to a prepared substrate. Please refer to the appropriate application guide for information about correct surface preparation. Mixing First stir the tub contents thoroughly. Then add the catalyst while stirring the resin at the slow-speed setting and mix for 2 minutes. Make sure that the product on the base and sides of the container is mixed in. At product temperatures < 10 C the product should be stirred for 5 minutes, as the catalyst will take longer to dissolve. Application Use the sheepskin roller to apply an even film-forming coat of primer. Avoid creating puddles of primer. Once the coating has cured, apply a second coat to cover any defects (bubbles, areas not fully coated). Preparation for subsequent layers For the subsequent application of Polimar FCS Levelling Mortar: Once the primer has hardened, apply a second layer and top with a little quartz sand ( kg/m2 at mm) while the primer is still wet. The sand topping creates the necessary key, i.e. roughness, for application of the mortar. Never apply the sand topping to the first coat of primer. Cleaning If work is interrupted or when it is completed, clean the tools thoroughly with Polimar Acetone Cleaner within the pot life of the material (approx. 10 minutes). This can be done with a brush. Do not use the tools again until the Acetone Cleaner has evaporated fully. Simply immersing the tools in the Acetone Cleaner will not prevent the material from hardening.

12 Polimar FCS Fleece & Polimar FCS Detailing Fleece Product Data Sheet May 2014 Polimar FCS Fleeces are synthetic-fibre fleeces specially designed for use with Polimar FCS waterproofing and detailing resins. Description Polimar FCS Fleeces are synthetic-fibre fleece specially designed for use with Polimar FCS waterproofing and detailing resins. The fleece enables the layer thickness to be controlled when applying waterproofing resins and also has a strengthening and crack-bridging effect in the hardened waterproofing layer. Material Mechanically strengthened and heat-set special synthetic-fibre fleece with a weight per unit area of 110 g/m2 Features and Benefits High tear strength and tear-propagation resistance High elongation at break Specially designed for use with Polimar FCS waterproofing and detailing resins in terms of material properties, thickness and degree of density Facilitates easy and reliable application of waterproofing with layer thickness control function Areas of Application Polimar FCS Fleeces are used as reinforcement and to ensure a minimum layer thickness for Polimar FCS waterproofing resins to create high-quality, flexible and crack-bridging waterproofing systems. Packaging Polimar FCS Detailing Fleece Polimar FCS Fleece Roll (W x L) 26cm x 50m 105cm x 50m Colours White. Storage Store Polimar FCS Fleeces in a dry place, protected against moisture and dirt, and if possible, in a horizontal position. Product Application A single layer of the fleece is fully saturated with Polimar FCS waterproofing or detailing resins according to the specification. Overlaps in Polimar FCS Fleece must be a minimum of 50mm. For further information please refer to the product information sheets for Polimar FCS waterproofing and detailing resins.

13 Polimar FCS Filler Product Data Sheet May 2014 Polimar FCS Filler is a fast reactive and flexible product used to fill small cracks and joints as well as to smooth out areas of minor unevenness. Description Polimar FCS Filler is a fast reactive and flexible product used to fill small cracks and joints as well as to smooth out areas of minor unevenness. It is used mainly to prepare the substrate before Polimar waterproofing and surfacing systems are applied. Material A two-component, fast-reactive, filled and flexible PMMA-based (polymethyl methacrylate) sealing resin. Features and Benefits Easy to apply Can also be applied at sub zero temperatures Fast curing Hydrolysis and alkali resistant Solvent free Areas of Application Polimar FCS Filler is used to fill small cracks and joints in order to prepare the substrate before Polimar waterproofing and surfacing systems are applied. The product can also be used to smooth out fleece overlaps in the waterproofing layer. Packaging kg Polimar FCS Filler Must be mixed with 2 bags of Polimar FCS Catalyst Colours Polimar FCS Filler is available in the following standard colour: RAL 7032 Light grey Storage Store products sealed in their original airtight container and in a cool, dry and frost-free place. Unopened products have a shelf life of at least 6 months. Direct sunlight on the containers should be avoided, including on site. After removing some of the contents, reseal the containers so they are airtight. Application conditions Temperature Product Temperature range, in C Air Substrate* Material Polimar FCS Filler -5 to to +50* +3 to +30 * The substrate temperature must be at least 3 C above the dew point during application and curing. Moisture The relative humidity must be 90 %. The surface to be coated must be dry and ice-free. The surface must be protected from moisture until the coating has hardened.

14 Reaction times Polimar FCS Filler (at 20 C, 3 % catalyst) Pot life: approx. 15 minutes Rain-proof after: approx. 30 minutes Can be walked on / overcoated after: approx. 45 minutes Curing time approx. 3 hours Higher temperatures or greater proportions of catalyst will reduce reaction times, while lower temperatures and smaller proportions of catalyst will increase reaction times. Consumption rates Substrate Smoothing fleece overlaps Filling Technical data Density: Consumption 0.30 kg/m run 1.70 kg/l 1.71 g/cm³ Product Application Cleaning Application equipment / tools For mixing the product: Twin-paddle stirrer For applying the product: Smoothing trowel or finishing trowel Substrate preparation Apply the Polimar FCS Filler to the hardened Polimar FCS Primer. Mixing First stir the tub contents thoroughly. Then add Polimar FCS Catalyst (2 bags) while stirring at the slowspeed setting and mix for 2 minutes. Make sure that the product on the base and sides of the container is mixed in. At product temperatures < 10 C the product should be stirred for 4 minutes, as the catalyst will take longer to dissolve. Application Fill in small cracks or joints using a pointing trowel or finishing trowel. Use the pointing trowel to smooth over minor differences in height. Preparation for subsequent layers None required If work is interrupted or when it is completed, clean the tools thoroughly with Polimar Acetone Cleaner within the pot life of the material (approx. 10 minutes). This can be done with a brush. Do not use the tools again until the Acetone Cleaner has evaporated fully. Simply immersing the tools in the Acetone Cleaner will not prevent the material from hardening. Safety Information Please refer to the safety data sheets for the products used.

15 Polimar FCS Reinforced Filler Product Data Sheet May 2014 Polimar FCS Reinforced Filler is a highly flexible, fibre-filled waterproofing product for sealing minor penetrations. Description Polimar FCS Reinforced Filler is a highly flexible, fibre-filled waterproofing product for sealing small and intricate details where fleece reinforced waterproofing is difficult to use. It allows these areas to be waterproofed and incorporated safely into the waterproofing system. Material A two-component, fast-reactive, highly flexible, thixotropic and fibre-filled waterproofing material. Features and Benefits Reliable incorporation of small, geometrically complex shapes in the seamless Polimar FCS reinforced waterproofing system Highly flexible, even at extreme sub-zero temperatures Permanently weather-resistant (UV-, hydrolysis- and alkali-resistant) Fully bonded to the substrate, therefore no flow paths for water Easy and fast application Fast-curing Can also be applied at sub-zero temperatures Can be applied to almost all substrates, including variable substrates (when combined with Polimar FCS Primers) Solvent-free Areas of Application Polimar FCS Reinforced Filler is used for the waterproofing of small, geometrically complex details with limited crack movement, Its use is restricted to the waterproofing of details that cannot be sealed using fleecereinforced Polimar FCS waterproofing products on account of the geometric shape of those details. With Polimar FCS Reinforced Filler these details can be securely incorporated in the fleece-reinforced waterproofing for the main area. Packaging 10.00kg Polimar FCS Reinforced Filler Must be mixed with 2 bags of Polimar FCS Catalyst Colours Polimar FCS Reinforced Filler is supplied in the standard colour of 7032 Light grey. Storage Store the products sealed in their original airtight container and in a cool, dry and frost-free place. Unopened products have a shelf life of at least 6 months. Direct sunlight on the containers should be avoided, including on site. After removing some of the contents, reseal the containers so they are airtight. Application conditions Temperature Product Temperature range, in C Air Substrate* Material Polimar FCS Reinforced Filler -5 to to +50* +3 to +30 * The substrate temperature must be at least 3 C above the dew point during application and curing.

16 Moisture The relative humidity must be 90 %. The surface to be coated must be dry and ice-free. The surface must be protected from moisture until the coating has hardened. Reaction times Polimar FCS Reinforced Filler (at 20 C, 3% catalyst) Pot life: approx. 10 minutes Rain-proof after: approx. 20 minutes Can be walked on / overcoated after: approx. 45 minutes Curing time approx. 2 hours Higher temperatures or greater proportions of catalyst will reduce reaction times, while lower temperatures and smaller proportions of catalyst will increase reaction times. Consumption rates 1.4 kg/m² per mm layer thickness Technical data Density: 1..22g/cm³ Product Application Application equipment / tools For mixing the product: Twin-paddle stirrer Cleaning For applying the product: Brush Substrate preparation Apply the Polimar FCS Reinforced Filler to the cured Polimar FCS Primer or suitably prepared substrate. Mixing First stir the tub contents thoroughly. Then add Polimar FCS Catalyst (2 bags) while stirring the resin at the slow-speed setting and mix for 2 minutes. Make sure that the product on the base and sides of the container is mixed in. At product temperatures < 10 C the product should be stirred for 4 minutes, as the catalyst will take longer to dissolve. Application With a brush, apply a thick layer to the detail to be waterproofed and smooth over. Make sure that a layer thickness of at least 1.5 mm is achieved in all areas. If necessary, apply a second layer once the first one has hardened. Preparation for subsequent layers: None required. If work is interrupted or when it is completed, clean the tools thoroughly with Polimar Acetone Cleaner within the pot life of the material (approx. 10 minutes). This can be done with a brush. Do not use the tools again until the Acetone Cleaner has evaporated fully. Simply immersing the tools in the Acetone Cleaner will not prevent the material from hardening.

17 Polimar FCS Levelling Mortar Product Data Sheet May 2014 Polimar FCS Levelling Mortar is a fast-reactive repair and levelling mortar used for filling and smoothing over faults and cavities in the substrate. Description Polimar FCS Levelling Mortar is a fast-reactive repair and levelling mortar used for filling and smoothing over faults and cavities in the substrate. Material A two-component, fast-reactive, highly filled PMMA-based (polymethyl methacrylate) repair and levelling mortar with a formulated, activated filler mix. Features and Benefits Easy to apply Can also be applied at sub-zero temperatures Fast-curing Thermoplastic behaviour Stable under pressure Abrasion-resistant Watertight (subject to correct intermediate compression) Resistant to frost Largely resistant to acids, alkali solutions and diesel UV-, hydrolysis- and alkali-resistant Solvent-free Areas of Application Polimar FCS Levelling Mortar is used as a repair and levelling mortar as well as to even out gradients on cement-bound and bitumen-bound substrates. Consequently it can be used as a reprofiling mortar under IKO Polimar FCS products, as a replacement for mastic asphalt or asphalt concrete. Packaging 1.00kg resin (Component A) 9.00kg aggregate mix (Component B) Note: The aggregate mix (Component B) contains catalyst and no additional Polimar FCS Catalyst is required Colours Polimar FCS Levelling Mortar is asphalt black. Storage Store products sealed in their original packaging and in a cool, dry and frost-free place. Avoid warm storage areas (>30 C) even for brief periods, for example on site. Consequently the products must not be exposed to direct sunlight or kept in a vehicle. Unopened products have a shelf life of at least 3 months. After removing some of the contents, reseal the containers so they are airtight. Application conditions Temperature Product Temperature range, in C Air Substrate* Material Polimar FCS Levelling Mortar -5 to to +50* +3 to +30 * The substrate temperature must be at least 3 C above the dew point during application and curing. Moisture The relative humidity must be 90 %. The surface to be coated must be dry and ice-free. The surface must be protected from moisture until the coating has hardened.

18 Reaction times Polimar FCS Levelling Mortar (at 20 C) Pot life: approx. 15 minutes Rain-proof after: approx. 30 minutes Can be walked on / overcoated after: approx. 1 hour Curing time approx. 3 hours Higher temperatures or greater proportions of catalyst will reduce reaction times, while lower temperatures and smaller proportions of catalyst will increase reaction times. Consumption rates 2.2 kg/m² per mm layer thickness Technical data Density: Polimar FCS Levelling Mortar Resin Activated filler mix 2.19 g/cm³ 0.99 g/cm³ 2.61 g/cm³ Product Application Cleaning Application equipment / tools For mixing the product: Stirrer with spiral mixer head For applying the product: Smoothing trowel Substrate preparation The mortar is applied to the hardened Polimar FCS Primer. Mixing Shake the resin component and add all of it to the sand mixture. Then stir fully for 3 minutes using a compulsory mixer (spiral mixer head). There must be no lumps or nodules and all the material on the base and walls of the container must be incorporated. To ensure that this is done, it is helpful to repot the material once during the mixing process. N.B. Catalyst does not need to be added. The catalyst is already included in the aggregate component. Application Pour the mortar onto the primed surface, compress and finish immediately with a smoothing trowel. The mortar can be applied in layer thicknesses of up to 50 mm in a single operation. Please note: Make sure that the mortar is worked well into the corners (compressed). Preparation for subsequent layers None required If work is interrupted or when it is completed, clean the tools thoroughly with Polimar Acetone Cleaner within the pot life of the material (approx. 10 minutes). This can be done with a brush. Do not use the tools again until the Acetone Cleaner has evaporated fully. Simply immersing the tools in the Acetone Cleaner will not prevent the material from hardening.

19 Polimar FCS Catalyst Product Data Sheet April 2014 Description Polimar FCS Catalyst is an essential component of PMMA-based Polimar products. It both starts and adjusts the curing reaction. The speed of the reaction is adjusted to the ambient conditions by modifying the amount of catalyst added. Material Oxygen-rich, powdered peroxide-based compound Features and Benefits Easily soluble Highly effective Areas of Application Polimar FCS Catalyst is mixed with Polimar PMMA products to enable the curing process to take place. It both initiates and controls the speed of the curing reaction. The reaction speed can be influenced by adjusting the amount added, and this method is used to adapt the reaction to the ambient conditions (temperatures). Packaging 0.10 kg in plastic bag Colours Polimar FCS Catalyst is a white powder. Storage The catalyst must only be stored in closed containers and in dry areas, away from heat and ignition sources, and at temperatures below +30 C. In the original packaging it has a minimum shelf life of 6 months. The influence of heat can cause the powder clump together and can reduce its effectiveness. The powder can selfignite if it is heated to a higher temperature, e.g. by direct sunlight. Consequently direct sunlight should also be avoided on site. Required amounts of catalyst The amount of catalyst required is dependent on the product used, the quantity of product and the temperature conditions. For further details about the recommended quantities of catalyst please refer to the product information sheets for Polimar PMMA-based products. Technical data Density: Apparent density: 1.23 g/cm³ 0.65 g/cm³ Product Application Application equipment / tools For mixing the product: Twin-paddle stirrer Mixing Add the catalyst to the PMMA-based product while stirring, as the stirring action causes the catalyst to dissolve and ensures an even distribution. For exact details please refer to the product information sheets of the PMMA-based products.

20 Polimar FCS Deco Chips Product Data Sheet May 2014 Description Polimar FCS Deco Chips are toppings specifically designed for Polimar FCS products. They offer design options for the finished surface, while also optimising its non-slip property. Material Acrylate-based topping Features and Benefits Receiver-compatible topping chips Can be used as a single colour or multiple colours Areas of Application Polimar FCS Deco Chips are applied to the sealing layer to enhance the appearance of the finish and enhance the slip-resistant properties of the surface. A slip-resistance level of up to R 10 can be achieved. Packaging 1.00kg in tub Colours Black, white & grey Storage Store the chips in a cool and dry area. Consumption Up to 50 g/m2 depending on the desired appearance Product Application Application equipment / tools Hopper spray gun Application Use the hopper spray gun to apply Polimar FCS Deco Chips to the sealer while the coating is still wet. Depending on the required design of the surface, the coloured chips can first be mixed and a greater or lesser amount applied. However, applying an excess quantity should be avoided, i.e.in their final position the chips applied should not form a continuous coating at any point.

21 General Information The above information, especially information about application of the products, is based on extensive development work as well as many years of experience and is provided to the best of our knowledge. However, the wide variety of requirements and conditions on site mean that it is necessary for the product to be tested to ensure that it is suitable for the intended purpose. Only the most recent version of the document is valid. We reserve the right to make changes to reflect advances in technology or improvements to our products. IKO PLC Literature Enquiries Tel: Website: Sales Support Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB Tel: Fax: Technical & Design Services Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB Tel: Fax: Whilst every care is taken to see that the information given in this literature is correct and up to date it is not intended to form part of any contract or give rise to any collateral liability, which is hereby specifically excluded. Intending purchasers of our materials should therefore verify with the company whether any changes in our specification or application details or otherwise have taken place since this literature was issued. Company Registered in England No Registered Office: Appley Lane North, Appley Bridge, Wigan, Lancashire, WN6 9AB