Technical Specification Sprayfiber-F Fire Protection Department

Transcription

1 INABENSA INABENSA Technical Specification Fire Protection Department

2 Technical Characteristics

3 is a mortar made by mineral wool and hydraulic binders, dry and inorganic, manufactured by Inabensa Protisa, developed specifically for fire protection of building elements. It is manufactured through a rigorous quality control that ensures the product is always equal to what was being tested in accredited official laboratories. In addition to its excellent properties in terms of passive fire protection, it provides excellent sound absorption, works as a condensation control element and it is an excellent thermal insulation product.

4 It is applied by spraying directly onto the support, quickly and easily using special pneumatic machine. Because of its flexibility is ideally suited to protect any support without cracks, one great advantage over traditional mortars. Adhesion is perfect in any support, no intermediate fixing mesh is necessary below 70 mm. thickness. Features: Grayish white. Uniform rough appearance. Various finishing options: raw, smoothed with a roller Paintable product. Excellent elastic thermal barrier without seams or joints. Protects against steel corrosion. Not toxic or pathogenic, is exempt from asbestos and crystalline silica in the free state. It does not emit toxic gases or hazardous in case of fire. It does not contains gypsum plaster. It is not attacked by fungi or rodents. Highly effective sound absorber Recommended uses: Construction: In edification it is used principally for fire protection of steel structures, composite slabs, concrete slabs, etc

5 General Application: is applied by a pneumatic spraying machine Depends of thickness it will be applied in two or more layers, applying successive layers of approximately 15 mm. each one. The preparation of steel prior to application of the primer is done according to the criteria defined in the data sheet for that product. Steel support must be clean, dust free, grease free, free oil and totally dry for a perfect mortar adherence. In case of old support, it must be free oxide and without corrosion. If corrosion exists, it must be removed by mechanical means, preferably by sandblasting, and should be applied an epoxi primer or similar. Although it is not necessary, support adherence could be improved using appropriate union bridges.

6 Finish: It is possible to get a final flat finish with trowel or similar few minutes after it had been projected. If needed a product with greater mechanical resistance to impacts and scratches, you can apply a finish layer by spraying special hardeners products. If it is necessary it could be used a compatible paint to protect from aggressive environment or just for aesthetic purposes.

7 Technical Characteristics: Powder bulk density (kg/m3) 200 ± 10% Bulk density setting (kg/m3) 250 ± 15% Thermal conductivity (Kcal / m h ºC) 25 ºC. 0,055 Compressive strength (Kg/mm2) 0,98 Anti-condensation (grams of water per gram of product) 2 Colour Fire reaction Grayish White A1 Acoustic Absorption: Thick Coefficient x 10-2 (Kz) Coef. 0,125 0,2 0, NCR 15mm 4 15, , mm 6 24,5 60, , Presentation. is presented in pallets of 24 bags, 24 Kg per bag. Bags are made with double leaf of Krafft paper with a polyethylene inner sheet. Storage. It should be stored off the ground, in a dry and covered place, protected from humidity and temperatures below 4ºC. With a correct storage the product is suitable for use during 12 months after manufacturing. Over this time limit, suitable use will depend of storage conditions and client responsibility. Security. To manipulate the product use dust mask, gloves and safety glasses. The product safety data sheet describes the security considerations

8 Main Tests: Fire resistance. Steel structure fire resistance tested with normative UNE EN :2005 Test method for determining the contribution to fire resistance of structural elements. Part 4: Protections applied to steel elements. Performed in Laboratory AFITI LICOF. Fire stability up to 240 minutes. Protection of composite floors concrete/steel according to UNE ENV :2005, performed in APPLUS Official Laboratory. Fire resistance up to 180 minutes depending of the composite floor. Fire resistance of perimeter fringe according to UNE EN :2000 based on the 2267 RD fire safety in industrial plants, performed in APPLUS Official Laboratory. Fire resistance of 60 and 90 minutes. Fire protection of Power Room containers according to UNE EN :2009 performed in APPLUS Official Laboratory. Fire resistance up to 180 minutes. Fire protection of sheet metal cover according to UNE :79 and UNE :81 performed in AFITI LICOF Official Laboratory. No Toxicity - National Research Council (Institute of Ceramics and Glass). I-61/91 Ref. Insulation - Ministry of Industry and Energy. Ref 46-83/EC Acoustic Absorption - Center of Applied Physics Torres Quevedo. Ref AC3D6.83 Main References: Bilbao Guggenheim Museum. Liceo Theater of Barcelona Campus Ciudad Financiera Santander, Boadilla del Monte. House Burning with Caja Madrid, Madrid. Hangars and facilities of Iberia in the Muñoza, Madrid. Industrial Building Fabrica de la Moneda, Madrid. National Cancer Research Center, Madrid

9 Instalaciones Inabensa - Protisa MADRID Los vascos, 17 2ª planta. protisa@abengoa.com Telf.: Inabensa Protisa has a system of quality assurance according to UNE EN ISO 9002 that ensures the product is free of defects. The information in this data sheet is based in our experience and technical knowledge, obtained from laboratory tests and bibliography. Protisa reserves the right to introduce any change without notice it. As use of this product is beyond our control, we only commit to replace or restore any product our laboratory find defective. We do not assume any responsibility or economical obligation beyond the purchase price of our products. Any other express or implied warranty is given. Any other use of this information beyond the stated purpose of this data sheet will not be Inabensa-Protisa s Responsibility