COPYRIGHT 2001 BY: GAMETIME REVISED: 08/09/01

Transcription

1

2

3

4

5 COPYRIGHT 2 BY: GAMETIME REVISED: 8/9/ 627 FITKID PARALLEL BAR NOTE: 627 2'-6" PARALLEL BAR 628 3' PARALLEL BAR 629 3'-" PARALLEL BAR 63 3'-6" PARALLEL BAR 63 3'-" PARALLEL BAR 632 '-2" PARALLEL BAR 633 '-6" PARALLEL BAR SPECIFICATIONS PARALLEL BAR: Shall be -7/8" O.D. gauge (.2") wall galvanized steel pipe. The bar shall have a powder coat finish. S PECIFICATIONS: GAMET IME has a policy of continuous improvement and reserves the right to discontinue or change specifications without notice. q Check for and repair damage caused by wear or vandalism, a major factor in injury-causing situations. q G AMETIME P ROVIDES ITS CUSTOMERS WITH COMPLETE S PECIICATION SHEETS AND INSTALLATION INSTRUCTIONS. TH E SPECIFICATION SHEET CONTAINS THE LISTING OF EVERY PART USED IN A PIECE OF EQUIPMENT AND SHOULD BE KEPT IN THE CUSTOMER'S F ILES FOR ACCURATE REFERENCE WHEN REPLACEMENT PARTS ARE NEEDED. q Never add components not intended for use with this product. q Proper maintenance of GAMET IME equipment requires regular tightening of all bolts, nuts, and set screws. q Never use GAMETIME playground equipment around or in conjunction with swimming pools, ponds, lakes or any other bodies of water. REPLACEMENT PARTS REF. NO. REQ'D. PART WEIGHT EA. NO. DESCRIPTION NO. LBS. KGS. Parallel Bar Parallel Bar Parallel Bar Extension 6" [5. cm] Extension " [25. cm] Extension '-2"[36. cm] Extension '-6"[6. cm] Hardware Complete /8" x 2" B.H.C.S *.9. 3/8" Lockwasher *.. 3/8" Tee-Nut (Spanner) *.3. UNLESS OTHERWISE SPECIFIED, ALL UNITS OF MEASURE ARE EACH *INCLUDED IN HARDWARE

6 LEGEND 9'--/8" [ cm] PART REFERENCE CONCRETE REQUIREMENT.39 CUBIC YARDS [.3 CUBIC METERS) DIM. 'B' DIM. 'A' NOTE: HOLE DEPTHS INDICATED ON ALL GROUND PLANS ARE MEASURED FROM THE FINISHED SURFACE. SEE FOOTING DETAILS. ALL FOOTING DIMENSIONS ARE BASED ON LEVEL FINISHED SURFACE. '-6" [5.72 cm] DIA. x 2'-6" [76.2 cm] DEEP ( PLACES) GROUND PLAN FINAL NO. DIM. 'A' DIM. 'B' DIM. 'C' 627 '--7/8" [35.3 cm] 9'--5/6" [32. cm] 2'-6" [76.2 cm] 628 '-3-7/8" [.39 cm] 9'--3/6" [32.68 cm] 3'-" [9. cm] 629 '-5-7/8" [5.7 cm] 9'--7/6" [33. cm] 3'-" [.6 cm] 63 '-7-7/8" [5.55 cm] 9'--3/" [3.2 cm] 3'-6" [6.68 cm] 63 '-9-7/8" [55.63 cm] '--/8" [35.9 cm] 3'-" [6.8 cm] 632 '--7/8" [6.7 cm] '--/2" [36.5 cm] '-2" [27. cm] 633 2'--7/8" [65.79 cm] '--5/6" [37. cm] '-6" [37.6 cm] DIM. 'C' DIM. 'A' FINISHED SURFACE EARTH S HOCK ABSORBING PROPERTIES OF SURFACING MATERIALS VARY. IF YOU DETERMINE THAT LESS THAN '-" [3.8 CM] OF SURFACING IS REQUIRED, M AKE UP THE DIFFERENCE IN ELEVATION WITH EARTH, BEFORE APPLYING SURFACING. SUGGESTED MINIMUM CONCRETE RATING: 3 PSI '-" [3.8 cm] 3.9"[. cm] MAX. SLOPED FOOTING IS A REQUIREMENT OF EUROPEAN STANDARD EN76-. '-6" [5.72 cm] 5 O MIN. DIM. 'A' DIMENSIONED TO TOP OF BRICK OR EQUIVALENT BRICK OR EQUIVALENT '-6" [5.66 cm] TYPICAL DETAIL "A" EARTH CONCRETE DIM. 'C' '-" [3.8 cm] FINISHED SURFACE EARTH 3.9"[. cm] MAX. '-6" [5.72 cm] 5 O MIN. 2 DIMENSIONED TO TOP OF BRICK OR EQUIVALENT BRICK OR EQUIVALENT '-6" [5.66 cm] DIAMETER (TYPICAL) DETAIL "B" EARTH CONCRETE

7 3/8" x 2" B.H.C.S. (855) 3/8" LOCKWASHER (8733) PARALLEL BAR 3/8" TEE-NUT (SPANNER) (8556) EXTENSION DETAIL "C" 2 SEE DETAIL 'C' ASSEMBLY DRAWING N OTE: Do not overtighten bolts. To overtighten may cause buckling or dimpling of some parts. NOTE: Read installation instructions thoroughly before starting assembly. Pour concrete only after final assembly is completed. Bracing material is required during assembly. N OTE: Assembly and leveling time will be greatly reduced if a transit is used to set location and depth of ground holes. N OTE: Place a brick or equivalent at the bottom of ground holes (where shown), to provide a solid foundation. Allow for this in the hole depth. STEP : Dig holes according to Ground Plan. NOTE: Due to extremes in weather and soil conditions, hole size may have to be increased to meet local conditions. SET-UP INSTRUCTIONS 3 S TEP 2: Attach the Extensions (if required) to the Parallel Bars using Detail 'C'. Place Parallel Bars into holes making sure they rest on the brick. S TEP 3: Level Parallel Bars using sway bracing. N OTE: It is recommended that 2" x " braces be cut the same lengths as the distance between each set of Parallel Bars noted on Assembly Drawing. Use the braces between bars to hold distance until concrete is poured and cured. STEP : Pour concrete according to the footing details. Allow 8 hours minimum for concrete to harden before using and removing sway braces. NOTE: Use loctite (supplied by others) on all threaded hardware.

8 TOP VIEWS SCALE: "='-" [:2] '-" [3.5 M] '-" [3.5 M] 627 '-3-3/6" [. M] '-5-3/6" [.5 M] 628 '-" [3.5 M] '-" [3.5 M] '-7-3/6" [.5 M] 629 '-9-3/6" [.55 M] 63 '-" [3.5 M] '-" [3.5 M] '--3/6" [.6 M] 2'--3/6" [.66 M] '-" [3.5 M] 2'-3-3/6" [.7 M] 633

9 R A Company INSTALLATION = DETAIL = PARTS LIST REFERENCE 3 2 8'-2 /6" [29.2 cm] '-5 /6" [.95 cm] TOP VIEW E5 E 32 E5 3 E ASSEMBLY DRAWING 2 FINISHED SURFACE 32 '-6 /" [6. cm] EACH END SIDE ELEVATION 3 E5 2'- 7/6" [6.57 cm] '-6" [5.72 cm] '-7 7/8" [9.97 cm] 6'-7 /8" [2.95 cm] 5'-" [52. cm] 5'- 5/6" [57.35 cm] GROUND PLAN FINISHED SURFACE '-3 7/6" [39. cm] '-2" [35.56 cm] X 2'-6" [76.2 cm] DEEP (5 REQUIRED) END ELEVATION NOTES:.) HOLE DEPTHS INDICATED ON ALL GROUND PLANS ARE MEASURE FROM THE FINISHED SURFACE. SEE DETAIL 32. ALL FOOTING DIMENSIONS ARE BASED ON LEVEL FINISHED SURFACE. 2.) CONCRETE REQUIRED:.3 CUBIC YARDS [.23 CUBIC METERS].

10 INSTALLATION INSTRUCTIONS.) Before starting assembly, review the General Installation Instructions at the beginning of this Installation Guide and the Typical Assembly Details in the back. 2.) Determine proper location for Sit-Up Station. Refer to Equipment Layout Plan provided and any applicable project site drawings. 3.) Dig footings for bench supports. Maintain footing spacing, size and depth as indicated on the ground plan. Refer to Detail 32. Allow for depth of desired Finished Surface..) Attach four legs to the bench. Refer to Detail E. 5.) Attach footrail assembly to bench. See Detail E5. 6.) Position assembled bench in footings; align, plumb, and brace bench in place. Pour concrete as shown on Detail 32. Be sure to hold top of concrete footing '-6" [5.2cm] down from the Finished Surface. Slope top of concrete for proper drainage. 7.) Refer to Sign Frame Installation Sheet for instructions on Sign mounting. 8.) Allow concrete a minimum of 8 hours to cure and harden before using bench. SPECIFICATIONS BENCH LEG: Shall be made of -7/8" O.D. galvanized pipe. BENCH ASSEMBLY: Shall be fabricated of punched steel metal with a plastisol coating. FOOTRAIL ASSEMBLY: Shall be an all-welded construction fabricated of 3-/2" O.D. (3 gauge) galvanized pipe, -5/6" O.D. galvanized pipe, 3/6" x 3" H.R. flat steel, and galvanized pipe cap. Final assembly shall also include cast aluminum caps and self-sealing pop rivets. FINISH: The Bench Legs, Footrail Assembly and Handrail Assembly shall all have a powder coat finish. HARDWARE: All nuts, bolts, screws, inserts, and lockwashers used in the assembly of all play equipment, shall be stainless steel, yellow dichromate plated steel, blue-coat plated steel, mechanically galvanized or powder coated/yellow dichromate plated steel. All primary fasteners shall be 3 series stainless steel. Fasteners with yellow dichromate treatment have an electro deposited, 99.9% pure zinc substrate applied from a specially formulated solution sealed with a yellow dichromate top coat designed to work in conjunction with the zinc plating. Yellow dichromate has a 32% longer life to white corrosion and 275% longer to red corrosion than does hot-dip galvanizing. SPECIFICATIONS: GAMETIME has a policy of continuous improvement and reserves the right to discontinue or change specifications without notice. ITEM 2 3 PARTS LIST DESCRIPTION BENCH LEG (3'- /2" [2.65cm]) PUNCHED STEEL BENCH ASS'Y FOOTRAIL ASS'Y SIT-UP STATION SIGN HARDWARE COMPLETE /2" ANCHOR ROD ('-" [3.8cm]) 3/8" x /" B.H.C.S. 3/8" FLAT WASHER ( /" O.D.) 3/8" LOCKWASHER 3/8" HEX NUT QTY PART NUMBER ** * 85* 872* 8733* 853* Unless Otherwise Specified, All Units of Measure are Each * Included in Hardware **Sign Frame with Hardware Sold Separately Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete. PAGE 2

11 INCH IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM DIMENSIONED TO TOP OF BRCK OR EQUIVALENT '-" [3.3 cm] '-6" [5.72cm] REFER TO OVERALL UNIT GROUND PLAN SHOCK ABSORBING PROPERTIES OF SURFACING MATERIALS M,AY VARY. IF YOU DETERMINE THAT LESS THAN '-" [3.8cm] OF SURFACING IS REQUIRED, MAKE UP THE DIFFERENCE IN ELEVATION WITH EARTH BEFORE APPLYING SURFACING. CONCRETE BRICK OR EQUIVALENT RESILIENT SURFACING CONFORMING TO APPLICABLE STANDARDS FOR EQUIPMENT FALL HEIGHT. ANCHOR ROD (WHERE APPLICABLE) SUBSTANTIAL COMPACTED SUBGRADE NOTES: -RESILIENT SURFACING AND SUBSTANTIAL COMPACTED SUBGRADE DEPTHS DEPEND ON SOIL CONDITIONS ANDRESILIENT SURFACING TYPE. -SLOPED FOOTINGS IS A REQUIREMENT OF EUROPEAN STANDARD EN76- ONLY -SUGGESTED MINIMUM CONCRETE RATING 3PSI. 3/8" HEX NUT (853) 3/8" LOCKWASHER (8733) 3/8" LOCKWASHER (8733) 3/8" FLATWASHER (872) BENCH ASSEMBLY 3/8" HEX NUT (853) BENCH ASSEMBLY BENCH LEG 3/8" FLATWASHER (872) 3/8" x /" B.H.C.S. (85) HANDRAIL ASSEMBLY 3/8" FLATWASHER (872) 3/8" x /" B.H.C.S. (85) PAGE 3

12 GTFit 325 R A Company ISSUED/REVISED: 3//6 CAPTAINS CHAIR INSTALLATION = DETAIL = PARTS LIST REFERENCE CAPTAINS CHAIR (SURFACE MOUNT) CAPTAINS CHAIR (FOOTING) CAPTAINS CHAIR (IN GROUND) 325S 325F 325I INSTALLATION INSTRUCTIONS. Before assembling this equipment, read the enclosed INSTALLER INSTRUCTIONS IN THE INSTALLATION BOOKLET; follow all the instructions during installation. 2. Using Captains Chair Machine as template, mark hole locations for 3/" Wedge Anchors. (See Anchor Detail) 2'-8 5/6" [8.99cm] 3 2'-5 5/6" [75.98cm] TOP VIEW ASSEMBLY DRAWING REF 2 3 CAPTAINS CHAIR DESCRIPTION FOOTBUCK WELD ASS'Y 3 /2" BASE COVER HARDWARE COMPLETE HARDWARE COMPLETE HARDWARE COMPLETE 3/" x 2" HEX HEAD CAP SCREW 3/" LOCKWASHER 3/" FLATWASHER (2" O.D.) 3/" HEX NUT 3/" ANCHOR BOLT 3/" x /" WEDGE ANCHOR Parts List 325S 325F I PART NUMBER * 8735* 872* 858* 8* 26358* /2" ANCHOR ROD * Unless Otherwise Specified, All Units of Measure are Each * Included in Hardware Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.

13 GTFit 325 R A Company ISSUED/REVISED: 3//6 LEG PRESS INSTALLATION = DETAIL = PARTS LIST REFERENCE LEG PRESS (SURFACE MOUNT) LEG PRESS (FOOTING) LEG PRESS (IN GROUND) 325S 325F 325I INSTALLATION INSTRUCTIONS. Before assembling this equipment, read the enclosed INSTALLER INSTRUCTIONS IN THE INSTALLATION BOOKLET; follow all the instructions during installation. 2. Using Leg Press Machine as template, mark hole locations for 3/" Wedge Anchors. (See Anchor Detail) 3'-8 3/8" [2.76 cm] 2 '- 5/6" [58.2 cm] TOP VIEW ASSEMBLY DRAWING REF 2 LEG PRESS DESCRIPTION 3 /2" BASE COVER FOOTBUCK WELD ASS'Y HARDWARE COMPLETE HARDWARE COMPLETE HARDWARE COMPLETE 3/" x 2" HEX HEAD CAP SCREW 3/" LOCKWASHER 3/" FLATWASHER (2" O.D.) 3/" HEX NUT 3/" ANCHOR BOLT 3/" x /" WEDGE ANCHOR Parts List 325S 325F I PART NUMBER * 8735* 872* 858* 8* 26358* /2" ANCHOR ROD * Unless Otherwise Specified, All Units of Measure are Each * Included in Hardware Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.

14 STOP IMPORTANT PRODUCT INFORMATION AND SAFETY WARNINGS STOP Installation over a hard surface such as concrete, asphalt, or packed earth may result in serious injury or death from fails. Especially all elevated upper-body strength building equipement. ALWAYS FOLLOW INSTALLATION INSTRUCTIONS WHEN ERECTING EQUIPMENT. Worn surfaces around equipment should be restored. Concrete footings should never be exposed. Surface depth should comply with installation instructions. Equipment should be placed to eliminate conflicting traffic patterns. All equipment should be free of rust and repainted whenever necessary to deter rusting. All protruding nuts and bolts should be covered; sharp edges on pipes should be capped or removed. Check for bent, broken or severely worn pipe and replace. Test overall stability and rigidity of all exercise equipment. Check for proper assembly, installation and ground anchoring. Check for and repair damage caused by wear or vandalism, a major factor in injury-causing situations. GameTime PROVIDES ITS CUSTOMERS WITH COMPLETE SPECIFICATION SHEETS AND INSTALLATION INSTRUCTIONS. THE SPECIFICATION SHEET CONTAINS THE LISTING OF EVERY PART USED IN A PIECE OF EQUIPMENT AND SHOULD BE KEPT IN THE CUSTOMER'S FILES FOR ACCURATE REFERENCE WHEN REPLACEMENT PARTS ARE NEEDED. Never add components not intended for use with this product. Regular checking of all parts, castings, etc. should be made. If a part is broken or worn it should be replaced immediately. Proper maintenance of GameTime equipment requires regular tightening of all bolts, nuts, and set screws. Check to be sure all fittings are tight and that the bars and pipes do not move. PAGE 2

15 SPECIFICATIONS BACKREST: The Backrest shall be constructed from injection molded Nylon W6. BASE COVER: The Base Cover shall be constructed from aluminum and powder coated. BOLT CAP: The Bolt Cap shall be constructed from aluminum and powder coated. FOOTREST: The Footrest shall be constructed from injection molded Nylon W6. HANDLE GRIP: The Handle Grip shall be constructed from injection molded PVC. INSTRUCTIONS: The Instructions shall be constructed from aluminum produced by silk-screen printing. MAIN PIPE: The main frame shall be an all welded assembly fabricated from SPP (carbon steel pipe) and dual phase steel plate. The frame shall be powder coated. MODULE CASE: The Module Case shall be constructed from stainless steel and powder coated. POST CAP: The Post Cap shall be constructed from injection molded Polyethylene. SADDLE: The Saddle shall be constructed from injection molded Nylon W6. HARDWARE: All nuts, bolts, screws, and lock washers used in the assembly shall be stainless steel, yellow dichromate plated steel, blue-coat plated steel, mechanically galvanized or powder coated/yellow dichromate plated steel. All primary fasteners shall be 3 alloy stainless steel. Fasteners with yellow dichromate treatment have an electro-deposited, 99.9% pure zinc substrate applied from a specially formulated solution sealed with a yellow dichromate top coat designed to work in conjunction with the zinc plating. PAGE 3

16 3/" LOCKWASHER (8735) 3/" x /" WEDGE ANCHOR (26358) BASE PLATE RESILIENT SURFACING CONFORMING TO APPLICABLE STANDARDS FOR EQUIPMENT FALL HEIGHT. WIRE MESH SUBSTANTIAL COMPACTED SUBGRADE NOTES: -LOOSE FILL SURFACING NOT RECOMMENDED FOR SURFACE MOUNT. EXISTING CONCRETE MUST BE MINIMUM 3, PSI, " MINIMUM DEPTH, WITH WIRE MESH REINFORCEMENT. MINIMUM 7 DAYS CURE-FULL CURE AFTER 28 DAYS. -RESILIENT SURFACING AND SUBSTANTIAL COMPACTED SUBGRADE DEPTHS DEPEND ON SOIL CONDITIONS AND RESILIENT SURFACING TYPE. SURFACE MOUNT 3/" HEX NUT (858) 3/" LOCKWASHER (8735) 3/" FLATWASHER (2"O.D.) (872) 3/" ANCHOR BOLT (8) 2'-" [6.96 cm] BASE PLATE RESILIENT SURFACING CONFORMING TO APPLICABLE STANDARDS FOR EQUIPMENT FALL HEIGHT. CONCRETE REQUIRED:.23 CUBIC YARDS.8 CUBIC METERS SUBSTANTIAL COMPACTED SUBGRADE NOTES: -RESILIENT SURFACING AND SUBSTANTIAL COMPACTED SUBGRADE DEPTHS DEPEND ON SOIL CONDITIONS AND RESILIENT SURFACING TYPE. -SUGGESTED MINIMUM CONCRETE RATING 3 PSI. 2'-" [6.96 cm] DIAMETER FOOTING DETAIL CONCRETE (CURE 7 DAYS MIN.) PAGE

17 2'-" [6.96 cm] 2'-" [6.96 cm] RESILIENT SURFACING CONFORMING TO APPLICABLE STANDARDS FOR EQUIPMENT FALL HEIGHT. '-" [3.8 cm] 3/" x 2" HEX HEAD CAP SCREW (8533) 3/" FLATWASHER (2" O.D.) (872) BASE PLATE 3/" LOCKWASHER (8735) 3/" HEX NUT (858) R3.9" [. cm] MAX. VARIES (REFER TO OVERALL UNIT GROUND PLAN) 5 MIN. 2'-" [6.96 cm] CONCRETE DIMENSIONED TO TOP OF BRICK OR EQUIVALENT. SUBSTANTIAL COMPACT SUBGRADE CONCRETE NOTES: -RESILIENT SURFACING AND SUBSTANTIAL COMPACTED SUBGRADE DEPTHS DEPEND ON SOIL CONDITIONS AND RESILIENT SURFACING TYPE. -SLOPED FOOTING IS A REQUIREMENT OF EUROPEAN STANDARD EN76- ONLY 2'-" [6.96 cm] FOOTBUCK WELD ASS'Y BRICK OR EQUIVALENT CONCRETE REQUIRED.3 CUBIC YARDS [.23 CUBIC METERS] SHOCK ABSORBING PROPERTIES OF SURFACING MATERIALS VARY. IF YOU DETERMINE THAT LESS THAN '-" [3.8cm] OF SURFACING IS REQUIRED, MAKE UP THE DIFFERENCE IN ELEVATION WITH EARTH, BEFORE APPLYING SURFACING. -SUGGESTED MINIMUM CONCRETE RATING 3 PSI. IN-GROUND MOUNT PAGE 5

18 INCH DETAILS for 325S IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM /" HEX NUT 3/" LOCKWASHER (8735) 3/" FLATWASHER DRILL 3/" x 2 /2" HOLE IN CONCRETE TO RECEIVE WEDGE ANCHORS 3/" x /" WEDGE ANCHOR (26358) SURFACE MOUNT ASS'Y DETAIL PAGE 6

19 INCH DETAILS for 325F IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM /" HEX NUT (858) 3/" LOCKWASHER (8735) 3/" FLATWASHER (2" O.D.) (872) 3/" FLATWASHER (2" O.D.) (872) 3/" HEX NUT (858) 3/" ANCHOR BOLT (8) FOOTER ASS'Y DETAIL PAGE 7

20 INCH DETAILS for 325I IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM /" x 2" HEX HEAD CAP SCREW (8533) 3/" FLATWASHER (2" O.D.) (872) 3/" LOCKWASHER (8735) 3/" HEX NUT (858) /2" ANCHOR ROD (3538) IN-GROUND ASS'Y DETAIL PAGE 8

21 INCH DETAILS for 325 IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM BASE COVER NUT EQUIPMENT POST BASE COVER BASE COVER BOLT BASE COVER BOLT BASE COVER NUT BASE COVER BASE COVER DETAIL PAGE 9

22 INCH DETAILS for 325 IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM CHAIR PIPE ASS'Y SPACER LARGE WASHER (M2-x3T) WASHER (M2) NYLON NUT (M2) NUT CAP (M2) SQUARE BAR & MAIN SHAFT ASS'Y HINGE ASS'Y MAIN POST ASS'Y LOCKWASHER (M 2) CAP WASHER (M2) SQUARE WASHER CHAIR PIPE ASS'Y DETAIL PAGE

23 GTFit 3255 R A Company ISSUED/REVISED: 3//6 ELLIPTICAL INSTALLATION = DETAIL = PARTS LIST REFERENCE ELLIPTICAL (SURFACE MOUNT) ELLIPTICAL (FOOTING) ELLIPTICAL (IN GROUND) 3255S 3255F 3255I INSTALLATION INSTRUCTIONS. Before assembling this equipment, read the enclosed INSTALLER INSTRUCTIONS IN THE INSTALLATION BOOKLET; follow all the instructions during installation. 2. Using Elliptical Machine as template, mark hole locations for 3/" Wedge Anchors. (See Anchor Detail) '-6 5/8" [7.25cm] 3'-9 7/6" [5.cm] 2 TOP VIEW ASSEMBLY DRAWING REF ELLIPTICAL DESCRIPTION FOOTBUCK WELD ASS'Y HARDWARE COMPLETE HARDWARE COMPLETE HARDWARE COMPLETE 3/" x 2" HEX HEAD CAP SCREW 3/" LOCKWASHER 3/" FLATWASHER (2" O.D.) 3/" HEX NUT 3/" ANCHOR BOLT 3/" x /" WEDGE ANCHOR /2" ANCHOR ROD Parts List 3255S 3255F I 2 PART NUMBER * 8735* 872* 858* 8* 26358* 3538* Unless Otherwise Specified, All Units of Measure are Each * Included in Hardware Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.

24 STOP IMPORTANT PRODUCT INFORMATION AND SAFETY WARNINGS STOP Installation over a hard surface such as concrete, asphalt, or packed earth may result in serious injury or death from fails. Especially all elevated upper-body strength building equipement. ALWAYS FOLLOW INSTALLATION INSTRUCTIONS WHEN ERECTING EQUIPMENT. Worn surfaces around equipment should be restored. Concrete footings should never be exposed. Surface depth should comply with installation instructions. Equipment should be placed to eliminate conflicting traffic patterns. All equipment should be free of rust and repainted whenever necessary to deter rusting. All protruding nuts and bolts should be covered; sharp edges on pipes should be capped or removed. Check for bent, broken or severely worn pipe and replace. Test overall stability and rigidity of all exercise equipment. Check for proper assembly, installation and ground anchoring. Check for and repair damage caused by wear or vandalism, a major factor in injury-causing situations. GameTime PROVIDES ITS CUSTOMERS WITH COMPLETE SPECIFICATION SHEETS AND INSTALLATION INSTRUCTIONS. THE SPECIFICATION SHEET CONTAINS THE LISTING OF EVERY PART USED IN A PIECE OF EQUIPMENT AND SHOULD BE KEPT IN THE CUSTOMER'S FILES FOR ACCURATE REFERENCE WHEN REPLACEMENT PARTS ARE NEEDED. Never add components not intended for use with this product. Regular checking of all parts, castings, etc. should be made. If a part is broken or worn it should be replaced immediately. Proper maintenance of GameTime equipment requires regular tightening of all bolts, nuts, and set screws. Check to be sure all fittings are tight and that the bars and pipes do not move. PAGE 2

25 SPECIFICATIONS BASE COVER: The Base Cover shall be constructed from aluminum and powder coated. BOLT CAP: The Bolt Cap shall be constructed from aluminum and powder coated. FOOTREST: The Footrest shall be constructed from injection molded Nylon W6. HANDLE GRIP: The Handle Grip shall be constructed from injection molded PVC. INSTRUCTIONS: The Instructions shall be constructed from aluminum produced by silk-screen printing. MAIN PIPE: The main frame shall be an all welded assembly fabricated from SPP (carbon steel pipe) and dual phase steel plate. The frame shall be powder coated. SADDLE: The Saddle shall be constructed from injection molded Nylon W6. HARDWARE: All nuts, bolts, screws, and lock washers used in the assembly shall be stainless steel, yellow dichromate plated steel, blue-coat plated steel, mechanically galvanized or powder coated/yellow dichromate plated steel. All primary fasteners shall be 3 alloy stainless steel. Fasteners with yellow dichromate treatment have an electro-deposited, 99.9% pure zinc substrate applied from a specially formulated solution sealed with a yellow dichromate top coat designed to work in conjunction with the zinc plating. PAGE 3

26 3/" LOCKWASHER (8735) 3/" x /" WEDGE ANCHOR (26358) BASE PLATE RESILIENT SURFACING CONFORMING TO APPLICABLE STANDARDS FOR EQUIPMENT FALL HEIGHT. WIRE MESH SUBSTANTIAL COMPACTED SUBGRADE NOTES: -LOOSE FILL SURFACING NOT RECOMMENDED FOR SURFACE MOUNT. EXISTING CONCRETE MUST BE MINIMUM 3, PSI, " MINIMUM DEPTH, WITH WIRE MESH REINFORCEMENT. MINIMUM 7 DAYS CURE-FULL CURE AFTER 28 DAYS. -RESILIENT SURFACING AND SUBSTANTIAL COMPACTED SUBGRADE DEPTHS DEPEND ON SOIL CONDITIONS AND RESILIENT SURFACING TYPE. SURFACE MOUNT 3/" HEX NUT (858) 3/" LOCKWASHER (8735) 3/" FLATWASHER (2"O.D.) (872) 3/" ANCHOR BOLT (8) 2'-" [6.96 cm] BASE PLATE RESILIENT SURFACING CONFORMING TO APPLICABLE STANDARDS FOR EQUIPMENT FALL HEIGHT. CONCRETE REQUIRED:.23 CUBIC YARDS.8 CUBIC METERS SUBSTANTIAL COMPACTED SUBGRADE NOTES: -RESILIENT SURFACING AND SUBSTANTIAL COMPACTED SUBGRADE DEPTHS DEPEND ON SOIL CONDITIONS AND RESILIENT SURFACING TYPE. -SUGGESTED MINIMUM CONCRETE RATING 3 PSI. 2'-" [6.96 cm] DIAMETER FOOTING DETAIL CONCRETE (CURE 7 DAYS MIN.) PAGE

27 2'-" [6.96 cm] 2'-" [6.96 cm] RESILIENT SURFACING CONFORMING TO APPLICABLE STANDARDS FOR EQUIPMENT FALL HEIGHT. '-" [3.8 cm] 3/" x 2" HEX HEAD CAP SCREW (8533) 3/" FLATWASHER (2" O.D.) (872) BASE PLATE 3/" LOCKWASHER (8735) 3/" HEX NUT (858) R3.9" [. cm] MAX. VARIES (REFER TO OVERALL UNIT GROUND PLAN) 5 MIN. 2'-" [6.96 cm] CONCRETE DIMENSIONED TO TOP OF BRICK OR EQUIVALENT. SUBSTANTIAL COMPACT SUBGRADE CONCRETE NOTES: -RESILIENT SURFACING AND SUBSTANTIAL COMPACTED SUBGRADE DEPTHS DEPEND ON SOIL CONDITIONS AND RESILIENT SURFACING TYPE. -SLOPED FOOTING IS A REQUIREMENT OF EUROPEAN STANDARD EN76- ONLY 2'-" [6.96 cm] FOOTBUCK WELD ASS'Y BRICK OR EQUIVALENT CONCRETE REQUIRED.3 CUBIC YARDS [.23 CUBIC METERS] SHOCK ABSORBING PROPERTIES OF SURFACING MATERIALS VARY. IF YOU DETERMINE THAT LESS THAN '-" [3.8cm] OF SURFACING IS REQUIRED, MAKE UP THE DIFFERENCE IN ELEVATION WITH EARTH, BEFORE APPLYING SURFACING. -SUGGESTED MINIMUM CONCRETE RATING 3 PSI. IN-GROUND MOUNT PAGE 5

28 INCH DETAILS for 3255S IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM /" HEX NUT 3/" LOCKWASHER (8735) 3/" FLATWASHER DRILL 3/" x 2 /2" HOLE IN CONCRETE TO RECEIVE WEDGE ANCHORS 3/" x /" WEDGE ANCHOR (26358) SURFACE MOUNT ASS'Y DETAIL PAGE 6

29 INCH DETAILS for 3255F IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM /" HEX NUT (858) 3/" LOCKWASHER (8735) 3/" FLATWASHER (2" O.D.) (872) 3/" FLATWASHER (2" O.D.) (872) 3/" HEX NUT (858) 3/" ANCHOR BOLT (8) FOOTER ASS'Y DETAIL PAGE 7

30 INCH DETAILS for 3255I IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM /" x 2" HEX HEAD CAP SCREW (8533) 3/" FLATWASHER (2" O.D.) (872) 3/" LOCKWASHER (8735) 3/" HEX NUT (858) /2" ANCHOR ROD (3538) IN-GROUND ASS'Y DETAIL PAGE 8

31 INCH DETAILS for 3255 IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM BASE COVER NUT EQUIPMENT POST BASE COVER BASE COVER BOLT BASE COVER BOLT BASE COVER NUT BASE COVER BASE COVER DETAIL PAGE 9

32 R GTFit A Company ISSUED/REVISED: //6 INSTALLATION = DETAIL = PARTS LIST REFERENCE CHIN UP STATION '-9 /6" [22.98 cm] '-3 /2" [3.8 cm] TOP VIEW HIGH 96" [23.8cm] LOW 8" [23.36cm] '-" [2.87 cm] ACCESSIBLE 63" [6.2cm] NOTE: REFER TO OVERALL TOP VIEW TO DETERMINE HIGH, LOW OR ACCESSIBLE INSTALLATION ASSEMBLY DRAWING SIDE ELEVATION '-6" [5.72 cm] x 2'-6" [76.2cm] DEEP (TYP) CONCRETE REQUIRED:.2 CUBIC YARDS [.5 CUBIC METERS] NOTE: HOLE DEPTHS INDICATED ON ALL GROUND PLANS ARE MEASURED FROM THE FINISHED SURFACE. SEE DETAIL 32. ALL FOOTING DIMENSIONS ARE BASED ON LEVEL FINISHED SURFACE. '-" [2.92 cm] GROUND PLAN

33 INSTALLATION INSTRUCTIONS NOTE: THIS INSTALLATION BOOKLET SHOULD BE KEPT IN CUSTOMER'S FILE FOR FUTURE REFERENCE. NOTE: Do not overtighten bolts. To overtighten may cause buckling or dimpling of some parts. NOTE: Read installation instructions thoroughly before starting assembly. Pour concrete only after final assembly is complete. Bracing material may be required during assembly. NOTE: Do not tighten any nuts, bolts, rods, etc. until the unit is completely assembled. NOTE: Assembly and leveling time will be greatly reduced if a transit is used to set location and depth of ground holes. NOTE: Due to extremes in weather and soil conditions, hole sizes may have to be increased to meet local conditions. STEP : Mark hole locations using Chin-Up Bars as template. STEP 2: Dig required holes and place a brick or equivalent at the bottom of holes (where shown) to provide a solid foundation. Allow for this in hole depth. See Detail 32. STEP 3: Lay all legs on ground arranged as required. Begin assembly Bars using Detail 86. After all Bars are in place, set the legs in the holes. Level all legs and cross bars and support them with wood or wire guys until the unit is ready for use. Be sure each leg is standing on a solid foundation block. STEP : Pour concrete to within '-" [3.8cm] of ground level and fill remaining with compacted subgrade and surfacing, Per Detail 32. Allow a minimum of 8 hours for concrete to cure and harden before using Chin-Up Station. SPECIFICATIONS NOTE: THIS INSTALLATION BOOKET SHOULD BE KEPT IN CUSTOMER'S FILE FOR FUTURE REFERENCE. NOTE: Read installation instructions thoroughly before starting assembly. Pour concrete only after final assembly is complete. Bracing material may be required during assembly. NOTE: Do not overtighten bolts. To overtighten may cause buckling or dimpling of some parts. NOTE: Do not tighten any nuts, bolts, rods, etc. until the unit is completely assembled. CHIN-UP BAR: The Chin-Up Bar assembly shall be constructed of.35" O.D. (2 GA) galvanized pipe,.29 O.D. galvanized pipe and 3/6" stainless steel tabs. The Crossbar shall be an all welded construction and coated with a custom formula of TGIC polyester powder coating after fabrication. HARDWARE: All nuts, bolts, screws, inserts, and lockwashers used in the assembly of all play equipment, shall be stainless steel, yellow dichromate plated steel, blue-coat plated steel, mechanically galvanized or powder coated/yellow dichromate plated steel. All primary fasteners shall be 3 series stainless steel. Fasteners with yellow dichromate treatment have an electro deposited, 99.9% pure zinc substrate applied from a specially formulated solution sealed with a yellow dichromate top coat designed to work in conjunction with the zinc plating Yellow dichromate has a 32% longer life to white corrosion and 275% longer to red corrosionthan does hot-dip galvanizing. SPECIFICATIONS: GAMETIME has a policy of continuous improvement and reserves the right to discontinue or change specifications without notice. Parts List REF. DESCRIPTION CHIN-UP BAR WELD ASS'Y HARDWARE COMPLETE 3/8" x /" B.H.C.S. 3/8" LOCKWASHER 2 CHIN-UP STATION NAME PLATE POP RIVET /2" ANCHOR ROD QTY 2 2 PART NUMBER * 8733* 2769* 3768* 3538* Unless Otherwise Specified, All Units of Measure are Each * Included in Hardware Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete. Note: Loctite (supplied by others) should be used on any non-patch hardware. PAGE 2

34 STOP IMPORTANT PRODUCT INFORMATION AND SAFETY WARNINGS STOP Installation over a hard surface such as concrete, asphalt, or packed earth may result in serious injury or death from fails. Especially all elevated upper-body strength building equipement. ALWAYS FOLLOW INSTALLATION INSTRUCTIONS WHEN ERECTING EQUIPMENT. Worn surfaces around equipment should be restored. Concrete footings should never be exposed. Surface depth should comply with installation instructions. Equipment should be placed to eliminate conflicting traffic patterns. All equipment should be free of rust and repainted whenever necessary to deter rusting. All protruding nuts and bolts should be covered; sharp edges on pipes should be capped or removed. Check for bent, broken or severely worn pipe and replace. Test overall stability and rigidity of all exercise equipment. Check for proper assembly, installation and ground anchoring. Check for and repair damage caused by wear or vandalism, a major factor in injury-causing situations. GameTime PROVIDES ITS CUSTOMERS WITH COMPLETE SPECIFICATION SHEETS AND INSTALLATION INSTRUCTIONS. THE SPECIFICATION SHEET CONTAINS THE LISTING OF EVERY PART USED IN A PIECE OF EQUIPMENT AND SHOULD BE KEPT IN THE CUSTOMER'S FILES FOR ACCURATE REFERENCE WHEN REPLACEMENT PARTS ARE NEEDED. Never add components not intended for use with this product. Regular checking of all parts, castings, etc. should be made. If a part is broken or worn it should be replaced immediately. Proper maintenance of GameTime equipment requires regular tightening of all bolts, nuts, and set screws. Check to be sure all fittings are tight and that the bars and pipes do not move. PAGE 3

35 INCH DETAILS for 3285 IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM UPRIGHT 3/8" LOCKWASHER (8733) INSTRUCTION PLATE 3/8" x " P.B.H.C.S. w/patch (825) CLIMBER POP RIVET (3768) DIMENSIONED TO TOP OF BRCK OR EQUIVALENT '-" [3.3 cm] '-6" [5.72cm] REFER TO OVERALL UNIT GROUND PLAN SHOCK ABSORBING PROPERTIES OF SURFACING MATERIALS M,AY VARY. IF YOU DETERMINE THAT LESS THAN '-" [3.8cm] OF SURFACING IS REQUIRED, MAKE UP THE DIFFERENCE IN ELEVATION WITH EARTH BEFORE APPLYING SURFACING. 32 SUBSTANTIAL COMPACTED SUBGRADE CONCRETE BRICK OR EQUIVALENT RESILIENT SURFACING CONFORMING TO APPLICABLE STANDARDS FOR EQUIPMENT FALL HEIGHT. ANCHOR ROD (WHERE APPLICABLE) NOTES: -RESILIENT SURFACING AND SUBSTANTIAL COMPACTED SUBGRADE DEPTHS DEPEND ON SOIL CONDITIONS ANDRESILIENT SURFACING TYPE. -SLOPED FOOTINGS IS A REQUIREMENT OF EUROPEAN STANDARD EN76- ONLY -SUGGESTED MINIMUM CONCRETE RATING 3PSI. PAGE

36 R GTFit A Company INSTALLATION = DETAIL = PARTS LIST REFERENCE '-9 /6" [22.98 cm] TOP VIEW 3'-9 3/6" [6.32 cm] APPLY LABEL IN APPROXIMATE LOCATION SHOWN ASSEMBLY DRAWING NOTE: REFER TO OVERALL TOP VIEW TO DETERMINE HIGH OR LOW INSTALLATION SIDE ELEVATION HIGH 32" [ 8.28cm] LOW 2" [3.8cm] '-6" [5.72 cm] x 2'-6" [76.2cm] DEEP (TYP) CONCRETE REQUIRED:.2 CUBIC YARDS [.5 CUBIC METERS] NOTE: HOLE DEPTHS INDICATED ON ALL GROUND PLANS ARE MEASURED FROM THE FINISHED SURFACE. SEE DETAIL 32. ALL FOOTING DIMENSIONS ARE BASED ON LEVEL FINISHED SURFACE. '-" [2.92 cm] GROUND PLAN

37 INSTALLATION INSTRUCTIONS NOTE: THIS INSTALLATION BOOKLET SHOULD BE KEPT IN CUSTOMER'S FILE FOR FUTURE REFERENCE. NOTE: Do not overtighten bolts. To overtighten may cause buckling or dimpling of some parts. NOTE: Read installation instructions thoroughly before starting assembly. Pour concrete only after final assembly is complete. Bracing material may be required during assembly. NOTE: Do not tighten any nuts, bolts, rods, etc. until the unit is completely assembled. NOTE: Assembly and leveling time will be greatly reduced if a transit is used to set location and depth of ground holes. NOTE: Due to extremes in weather and soil conditions, hole sizes may have to be increased to meet local conditions. STEP : Mark hole locations using Push-Up Bars as template. STEP 2: Dig required holes and place a brick or equivalent at the bottom of holes (where shown) to provide a solid foundation. Allow for this in hole depth. See Detail 32. STEP 3: Lay all legs on ground arranged as required. Begin assembly Bars using Detail 86. After all Bars are in place, set the legs in the holes. Level all legs and cross bars and support them with wood or wire guys until the unit is ready for use. Be sure each leg is standing on a solid foundation block. STEP : Pour concrete to within '-" [3.8cm] of ground level and fill remaining with compacted subgrade and surfacing, Per Detail 32. Allow a minimum of 8 hours for concrete to cure and harden before using Chin-Up Station. SPECIFICATIONS NOTE: THIS INSTALLATION BOOKET SHOULD BE KEPT IN CUSTOMER'S FILE FOR FUTURE REFERENCE. NOTE: Read installation instructions thoroughly before starting assembly. Pour concrete only after final assembly is complete. Bracing material may be required during assembly. NOTE: Do not overtighten bolts. To overtighten may cause buckling or dimpling of some parts. NOTE: Do not tighten any nuts, bolts, rods, etc. until the unit is completely assembled. PUSH-UP BAR: The Push-Up Bar assembly shall be constructed of.35" O.D. (2 GA) galvanized pipe,.29 O.D. galvanized pipe and 3/6" stainless steel tabs. The Crossbar shall be an all welded construction and coated with a custom formula of TGIC polyester powder coating after fabrication. HARDWARE: All nuts, bolts, screws, inserts, and lockwashers used in the assembly of all play equipment, shall be stainless steel, yellow dichromate plated steel, blue-coat plated steel, mechanically galvanized or powder coated/yellow dichromate plated steel. All primary fasteners shall be 3 series stainless steel. Fasteners with yellow dichromate treatment have an electro deposited, 99.9% pure zinc substrate applied from a specially formulated solution sealed with a yellow dichromate top coat designed to work in conjunction with the zinc plating Yellow dichromate has a 32% longer life to white corrosion and 275% longer to red corrosionthan does hot-dip galvanizing. SPECIFICATIONS: GAMETIME has a policy of continuous improvement and reserves the right to discontinue or change specifications without notice. REF. DESCRIPTION PUSH-UP BAR WELD ASS'Y HARDWARE COMPLETE 3/8" x /" B.H.C.S. 3/8" LOCKWASHER /2" ANCHOR ROD USAGE/WARNING LABEL Parts List QTY 2 PART NUMBER * 8733* 3538* 2762* Unless Otherwise Specified, All Units of Measure are Each * Included in Hardware Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete. Note: Loctite (supplied by others) should be used on any non-patch hardware. PAGE 2

38 STOP IMPORTANT PRODUCT INFORMATION AND SAFETY WARNINGS STOP Installation over a hard surface such as concrete, asphalt, or packed earth may result in serious injury or death from fails. Especially all elevated upper-body strength building equipement. ALWAYS FOLLOW INSTALLATION INSTRUCTIONS WHEN ERECTING EQUIPMENT. Worn surfaces around equipment should be restored. Concrete footings should never be exposed. Surface depth should comply with installation instructions. Equipment should be placed to eliminate conflicting traffic patterns. All equipment should be free of rust and repainted whenever necessary to deter rusting. All protruding nuts and bolts should be covered; sharp edges on pipes should be capped or removed. Check for bent, broken or severely worn pipe and replace. Test overall stability and rigidity of all exercise equipment. Check for proper assembly, installation and ground anchoring. Check for and repair damage caused by wear or vandalism, a major factor in injury-causing situations. GameTime PROVIDES ITS CUSTOMERS WITH COMPLETE SPECIFICATION SHEETS AND INSTALLATION INSTRUCTIONS. THE SPECIFICATION SHEET CONTAINS THE LISTING OF EVERY PART USED IN A PIECE OF EQUIPMENT AND SHOULD BE KEPT IN THE CUSTOMER'S FILES FOR ACCURATE REFERENCE WHEN REPLACEMENT PARTS ARE NEEDED. Never add components not intended for use with this product. Regular checking of all parts, castings, etc. should be made. If a part is broken or worn it should be replaced immediately. Proper maintenance of GameTime equipment requires regular tightening of all bolts, nuts, and set screws. Check to be sure all fittings are tight and that the bars and pipes do not move. PAGE 3

39 INCH IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM UPRIGHT 3/8" LOCKWASHER (8733) 3/8" x " P.B.H.C.S. w/patch (825) CLIMBER '-" [3.3 cm] RESILIENT SURFACING CONFORMING TO APPLICABLE STANDARDS FOR EQUIPMENT FALL HEIGHT. ANCHOR ROD (WHERE APPLICABLE) DIMENSIONED TO TOP OF BRCK OR EQUIVALENT '-6" [5.72cm] REFER TO OVERALL UNIT GROUND PLAN SHOCK ABSORBING PROPERTIES OF SURFACING MATERIALS M,AY VARY. IF YOU DETERMINE THAT LESS THAN '-" [3.8cm] OF SURFACING IS REQUIRED, MAKE UP THE DIFFERENCE IN ELEVATION WITH EARTH BEFORE APPLYING SURFACING. SUBSTANTIAL COMPACTED SUBGRADE CONCRETE BRICK OR EQUIVALENT NOTES: -RESILIENT SURFACING AND SUBSTANTIAL COMPACTED SUBGRADE DEPTHS DEPEND ON SOIL CONDITIONS ANDRESILIENT SURFACING TYPE. -SLOPED FOOTINGS IS A REQUIREMENT OF EUROPEAN STANDARD EN76- ONLY -SUGGESTED MINIMUM CONCRETE RATING 3PSI. PAGE

40 R GTFit A Company INSTALLATION = DETAIL = PARTS LIST REFERENCE CENTER OF PIPE '-2" [27cm] FINISHED GRADE CENTER OF PIPE APPLY USAGE/WARNING LABEL IN APPROXIMATE LOCATION SHOWN TOP SURFACE '-" [2.92cm] '-6" [5.72cm] FINISHED GRADE ASSEMBLY DRAWING 6'- 3/" [8.79 cm] '-3 /2" [3.8 cm] TOP VIEW

41 '-6" [5.72 cm] x '-" [58.2cm] DEEP 2'-" [6.96 cm] 5'- 3/6" [62.96 cm] '- /2" [5.3 cm] CONCRETE REQUIRED:.3 CUBIC YARDS [.23 CUBIC METERS] NOTE: HOLE DEPTHS INDICATED ON ALL GROUND PLANS ARE MEASURED FROM THE FINISHED SURFACE. SEE DETAIL 32 AND ELEVATION VIEW. ALL FOOTING DIMENSIONS ARE BASED ON LEVEL FINISHED SURFACE. GROUND PLAN '-6" [5.72 cm] x 2'-6" [76.2cm] DEEP (2 PLACES) '-" [2.92 cm] PAGE 2

42 INSTALLATION INSTRUCTIONS NOTE: THIS INSTALLATION BOOKLET SHOULD BE KEPT IN CUSTOMER'S FILE FOR FUTURE REFERENCE. NOTE: Do not overtighten bolts. To overtighten may cause buckling or dimpling of some parts. NOTE: Read installation instructions thoroughly before starting assembly. Pour concrete only after final assembly is complete. Bracing material may be required during assembly. NOTE: Do not tighten any nuts, bolts, rods, etc. until the unit is completely assembled. NOTE: Assembly and leveling time will be greatly reduced if a transit is used to set location and depth of ground holes. NOTE: Due to extremes in weather and soil conditions, hole sizes may have to be increased to meet local conditions. STEP : Mark hole locations using Ground Plan. STEP 2: Dig required holes and place a brick or equivalent at the bottom of holes (where shown) to provide a solid foundation. Allow for this in hole depth. See Detail 32 and Elevation View. STEP 3: Lay all legs on ground arranged as required. Begin assembly Bars using Detail 86. After all Bars are in place, set the legs in the holes. Level all legs and cross bars and support them with wood or wire guys until the unit is ready for use. Be sure each leg is standing on a solid foundation block. STEP : Attach Top Covers to Plyometric Frame using Detail 323. IMPORTANT: Make sure when attaching the Top Cover to place the Diamond Texture facing up. STEP 5: Attach /2" Anchor Rod to Plyometric Frame. STEP 6: Pour concrete to within '-" [3.8cm] of ground level and fill remaining with compacted subgrade and surfacing, Per Detail 32 and Elevation View. Allow a minimum of 8 hours for concrete to cure and harden before using. SPECIFICATIONS NOTE: THIS INSTALLATION BOOKET SHOULD BE KEPT IN CUSTOMER'S FILE FOR FUTURE REFERENCE. NOTE: Read installation instructions thoroughly before starting assembly. Pour concrete only after final assembly is complete. Bracing material may be required during assembly. NOTE: Do not overtighten bolts. To overtighten may cause buckling or dimpling of some parts. NOTE: Do not tighten any nuts, bolts, rods, etc. until the unit is completely assembled. PULL-UP BAR: The Pull-Up Bar assembly shall be constructed of.35" O.D. (2 GA) galvanized pipe and 3/6" stainless steel tabs. The Crossbar shall be an all welded construction and coated with a custom formula of TGIC polyester powder coating after fabrication. TOP COVER: Shall be 3/" HDPE Diamond Texture Sheet. PLYOMETRIC FRAME: Shall have a 5" (.2w) galvanized pipe with a 2Ga. hot rolled steel top. HARDWARE: All nuts, bolts, screws, inserts, and lockwashers used in the assembly of all play equipment, shall be stainless steel, yellow dichromate plated steel, blue-coat plated steel, mechanically galvanized or powder coated/yellow dichromate plated steel. All primary fasteners shall be 3 series stainless steel. Fasteners with yellow dichromate treatment have an electro deposited, 99.9% pure zinc substrate applied from a specially formulated solution sealed with a yellow dichromate top coat designed to work in conjunction with the zinc plating Yellow dichromate has a 32% longer life to white corrosion and 275% longer to red corrosionthan does hot-dip galvanizing. SPECIFICATIONS: GAMETIME has a policy of continuous improvement and reserves the right to discontinue or change specifications without notice. REF. 2 3 DESCRIPTION Parts List HORIZONTAL PULL-UP WELD ASS'Y TOP COVER 8" PLYOMETRIC FRAME HARDWARE COMPLETE 3/8" x 3/" P.B.H.C.S. w/patch 3/8" x /" B.H.C.S. 3/8" LOCKWASHER 3/8" BARREL NUT 3/8" FLAT WASHER /2" ANCHOR ROD USAGE/WARNING LABEL QTY 8 3 PART NUMBER * 85* 8733* 88* 87* 3538* 2756* Unless Otherwise Specified, All Units of Measure are Each * Included in Hardware Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete. Note: Loctite (supplied by others) should be used on any non-patch hardware. PAGE 3

43 STOP IMPORTANT PRODUCT INFORMATION AND SAFETY WARNINGS STOP Installation over a hard surface such as concrete, asphalt, or packed earth may result in serious injury or death from fails. Especially all elevated upper-body strength building equipement. ALWAYS FOLLOW INSTALLATION INSTRUCTIONS WHEN ERECTING EQUIPMENT. Worn surfaces around equipment should be restored. Concrete footings should never be exposed. Surface depth should comply with installation instructions. Equipment should be placed to eliminate conflicting traffic patterns. All equipment should be free of rust and repainted whenever necessary to deter rusting. All protruding nuts and bolts should be covered; sharp edges on pipes should be capped or removed. Check for bent, broken or severely worn pipe and replace. Test overall stability and rigidity of all exercise equipment. Check for proper assembly, installation and ground anchoring. Check for and repair damage caused by wear or vandalism, a major factor in injury-causing situations. GameTime PROVIDES ITS CUSTOMERS WITH COMPLETE SPECIFICATION SHEETS AND INSTALLATION INSTRUCTIONS. THE SPECIFICATION SHEET CONTAINS THE LISTING OF EVERY PART USED IN A PIECE OF EQUIPMENT AND SHOULD BE KEPT IN THE CUSTOMER'S FILES FOR ACCURATE REFERENCE WHEN REPLACEMENT PARTS ARE NEEDED. Never add components not intended for use with this product. Regular checking of all parts, castings, etc. should be made. If a part is broken or worn it should be replaced immediately. Proper maintenance of GameTime equipment requires regular tightening of all bolts, nuts, and set screws. Check to be sure all fittings are tight and that the bars and pipes do not move. PAGE

44 INCH IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM UPRIGHT 3/8" LOCKWASHER (8733) 3/8" x " P.B.H.C.S. w/patch (825) CLIMBER '-" [3.3 cm] RESILIENT SURFACING CONFORMING TO APPLICABLE STANDARDS FOR EQUIPMENT FALL HEIGHT. ANCHOR ROD (WHERE APPLICABLE) DIMENSIONED TO TOP OF BRCK OR EQUIVALENT '-6" [5.72cm] REFER TO OVERALL UNIT GROUND PLAN SHOCK ABSORBING PROPERTIES OF SURFACING MATERIALS M,AY VARY. IF YOU DETERMINE THAT LESS THAN '-" [3.8cm] OF SURFACING IS REQUIRED, MAKE UP THE DIFFERENCE IN ELEVATION WITH EARTH BEFORE APPLYING SURFACING. SUBSTANTIAL COMPACTED SUBGRADE CONCRETE BRICK OR EQUIVALENT NOTES: -RESILIENT SURFACING AND SUBSTANTIAL COMPACTED SUBGRADE DEPTHS DEPEND ON SOIL CONDITIONS ANDRESILIENT SURFACING TYPE. -SLOPED FOOTINGS IS A REQUIREMENT OF EUROPEAN STANDARD EN76- ONLY -SUGGESTED MINIMUM CONCRETE RATING 3PSI. PAGE 5

45 INCH IMPORTANT TO REDUCE THE RISK OF CLOTHING ENTANGLEMENT IN COMPLIANCE WITH ASTM F87, ANY BOLT END PROTRUDING MORE THAN TWO FULL THREADS BEYOND THE FACE OF THE NUT SHALL BE CUT-OFF FLUSH, FILED SMOOTH AND TREATED TO PREVENT CORROSION. NOTE: LOCTITE (SUPPLIED BY OTHERS) SHOULD BE USED ON ALL THREADED HARDWARE. NOTE: AFTER ASSEMBLY IS COMPLETE, PEEN TEE-NUTS AND FLATWASHERS TO MATCH RADIUS OF PIPE CM /8" BARREL NUT (88) IMPORTANT: MAKE SURE WHEN ATTACHING THE TOP COVER TO PLACE THE DIAMOND TEXTURE FACING UP. FRAME PAGE 6