Seem 4 LED Perimeter FSM4L_FL2

Transcription

1 Seem 4 LED Perimeter FSM4L_FL2 MUST BE INSTALLED PRIOR TO DRYWALL /HARD CEILING READ ALL INSTALLATION INSTRUCTIONS BEFORE BEGINNING INSTALLATION focal point parts key attention 3 power off power on 4 parts list outside corner housing 2 inside corner sliding sleeve (ss) (SHIPPED INSTALLED. SSB INDICATES A SLIDING SLEEVE AT BOTH ENDS) 3 j-rail 4 finish plate tie-wire/grid bracket 3 corner j-rail 4 hardware bag by others tie-wire bracket 7 joiner bracket 8 joiner bracket 9 lens end piece 0 lens tool GRID CEILING - /" or 9/" flat tee main runner required for finish edge. housing types (4' shown) WALL/CEILING PREP individual (may include sliding sleeves) j-rail must be flush with wall texture 7.37 overall height start (shown with sliding sleeve) wall texture must extend to bottom of j-rail 2.0 intermediate ceiling line end (shown with sliding sleeve) drywall/hard ceilings mount below housing. grid ceiling - /" or 9/" flat tee main runner required for finish edge. IS039 REV. E 208 Focal Point, LLC 44S. Pulaski Rd., Chicago, IL of

2 BASIC INSTALLATION STEPS - SLIDING SLEEVES SEE PG 3 CORNERS SEE PG 4 2 FOCAL POINT RECOMMENDS STARTING WITH CORNER INSTALLATION IF APPLICABLE SLIDING SLEEVE PAIRS (SSB) START & END WITH A SLIDING SLEEVE 3 GRID 4 MOUNT J-RAIL TO WALL hardware by others AVOID ALL CONTACT WITH LED SURFACE, LEDs ARE EASILY DAMAGED! DRYWALL/HARD CEILING bend tee tabs use caution: damage may result if housing impacts wall GRID lift housing into place engaging j-rail and tee grid level houisng and secure to structure above with tie-wire 7 8 x4 9 x4 0 repeat steps 2 - for each housing section IS039 REV. E 208 Focal Point, LLC 44S. Pulaski Rd., Chicago, IL of

3 2 3 REFERENCE INSTRUCTIONS ON INCLUDED TOOL FOR LENS INSTALLATION. 4 DRYWALL/HARD CEILING drywall/hard ceiling mounts below housing (structure by others) EMERGENCY SEE BATTERY MANUFACTURER INSTRUCTIONS emergency maximum mounting height: 3.00 SLIDING SLEEVES MAX LENGTH 2" PER SLEEVE SLIDING SLEEVES & CORNERS DO NOT INTEGRATE SINGLE SLIDING SLEEVE (SS): EXAMPLE: 2' run length - 20' housing = 2" sliding sleeve SLIDING SLEEVE PAIR (SSB): EXAMPLE: (2' run length - 20' housing) / 2 = " sliding sleeve on each end 2" " " IS039 REV. E 208 Focal Point, LLC 44S. Pulaski Rd., Chicago, IL of

4 remove knockouts for 2 3 electrical access if necessary 4 CUT FINISH PLATE TO DETERMINED LENGTH 7 8 CORNERS 4" MIN / " MAX PER SIDE INSIDE CORNER: 4"min/"max OUTSIDE CORNER: CORNERS & SLIDING SLEEVES DO NOT INTEGRATE INSIDE CORNER 4"min/"max."min."max OUTSIDE CORNER IS039 REV. E 208 Focal Point, LLC 44S. Pulaski Rd., Chicago, IL of

5 2 3 4 INSIDE CORNER SHOWN hardware by others lift housing into place engaging j-rail 7 remove knockouts for electrical access if necessary SECURE TO STRUCTURE ABOVE WITH TIE-WIRE ION each run requires electrical connection CUT FINISH PLATE TO DETERMINED LENGTH 2 3 IS039 REV. E 208 Focal Point, LLC 44S. Pulaski Rd., Chicago, IL of

6 DRIVER SERVICE 2 AVOID ALL CONTACT WITH LED SURFACE, LEDs ARE EASILY DAMAGED! Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC is prohibited. IS039 REV. E 208 Focal Point, LLC 44S. Pulaski Rd., Chicago, IL of