DIVISION 10 SPECIALITIES

Transcription

1 DIVISION SANITARY ACCESSORIES 01.1 Manufacturer: As noted on Drawings. Provide wall blocking as required. Provide accessories if required on Drawings Grab bars: one 42 behind and on side of water closet and one 18 mounted vertically. Rails to be 1 ¼ to 1 ½ diameter stainless steel pipe in accordance with ANSI A117.1.See drawings for mounting locations Mirror: 24 x36 with stainless steel frame located above lavatory, 40 maximum above floor. (Verify on Drawings.) 01.4 Barrier Free Requirements: Locate as per Barrier Free Accessibility requirements Pipe Covers: See Plumbing Section Public Rest Rooms: See Drawings for accessories Hand Dryer in Rest Rooms XLERATOR Hand Dryer by EXCEL Dryer, Inc., Model #XL- C, (208V) surface mounted, with 1.1 diameter nozzle. Phone: (Alternate: Sloan XLERATOR by Sloan Valve Company, Model EDH-503-CP, surface mounted. Phone: VALVE-9.) ITEMS SUPPLIED BY WAWA, INC. AND INSTALLED BY GENERAL CONTRACTOR 02.1 General Contractor to install the following items: A. Bulletin Boards (minimum of 4). B. Produce Bag Holders. C. Lockers: Bolt Lockers top and bottom. D. Job Aid Holders and Clipboards. E. License Board. 10-1

2 F. Complete Graphics Package including LCD Monitors, copper rail, etc. LED monitors that are in portrait mode should always be oriented with the bottom of the screen to the right. Remove LED monitor logos from all units using a Philips screwdriver. G. Soap Dispensers in Food Service and Wash Areas. H. Toilet Tissue Dispensers. I. Paper Towel Dispenser in Food Service Area. J. CSR Filter System, See Section K. Safes (G.C. to bolt safes to floor). L. Mop Holder M. Hose Holder N. Air Delight Dispenser Economizer 9000, model # (attach with screws) and Air Delight Micro-Burst 9000 refills (two per Restroom) O. Sanitizer Neat Seat Dispenser (one per restroom stall) P. Wawa Toilet Bowl Cleaner #89 Spray Bottle shelf manufactured by Chemstar Q. Trusses R. Steel S. Door Frames T. Bollards U. Hardware (except Overhead Door) V. Clocks W. Clipboard Racks X. Charity Collector at Checkout Counter Y. Ship Ladders into trusses Z. Broom Holders (2) 10-2

3 AA. Trash Bag Holders (2) BB. BAS CC. LCD Screens ITEMS SUPPLIED BY WAWA, INC., INSTALLED BY OTHERS, AND COORDINATED BY GENERAL CONTRACTOR 03.1 Items to be installed by others: A. Storefront B. Glazing C. Graphics D. Cabinets E. Refrigeration F. Trash Compactors G. First Aid Kit H. Sanitary Equipment I. Fire Extinguishers J. Intercom System & Muzak K. ATM s L. Soda & FCB Equipment M. Coffee Equipment & Espresso N. Milkshake Equipment O. Iced Coffee Equipment P. Phones 10-3

4 Q. CAT System R. Computers S. Register & Cash System T. Office Furniture U. Self-Serve Beverage System WIRE SHELVING 01.1 Location: At Three Compartment Sink (4-36 x12 required), and elsewhere as shown on Drawings. General Contractor to install wire shelves above Three Compartment Sink with lip at front of shelving facing upwards toward ceiling Materials: Vinyl coated, open-wire construction Blocking as indicated in the drawings TOILET PARTITIONS 05.1 General Summary A. Section Includes: 1. Plastic toilet compartment partitions for following applications: a. Toilet enclosures. b. Sight screens. c. Urinal screens. B. Related Requirements: 1. Division 05 Section "Metal Fabrications" for miscellaneous structural and support metal components required to secure compartments. 2. Division 06 Section "Rough Carpentry" for compartment anchorage to frame walls. 10-4

5 05.2 References A. International Code Council (ICC)/American National Standards Institute (ANSI): 1. ICC/ANSI A Accessible and Usable Buildings and Facilities, as applicable to toilet compartments designated as accessible. B. United States Department of Justice: 1. ADA - Americans with Disabilities Act, Excerpt from 28 CFR Part 36 - ADA Standards for Accessible Design. C. GREENGUARD Environmental Institute (GREENGUARD): 05.3 Action Submittals 1. GREENGUARD certified low emitting products. A. Product Data: Manufacturer's data sheets for each type of product indicated. Include fabrication details, description of materials and finishes. 1. Product Test Reports: When requested by Architect, submit documentation by qualified independent testing agency indicating compliance of products with requirements. B. Shop Drawings: Include overall product dimensions, floor plan, elevations, sections, details, and attachments to other work. Include choice of options with details Informational Submittals A. Warranty: Sample of special warranty Closeout Submittals A. Maintenance and cleaning instructions Quality Assurance A. Manufacturer Qualifications: Approved manufacturer listed in this section, with minimum 5 years experience in the manufacture of toilet compartments. B. Accessibility Requirements: Comply with requirements of ICC/ANSI 117.1, and with requirements of authorities having jurisdiction. C. Surface-Burning Characteristics: As determined by testing identical products according to ASTM E 84 by qualified testing agency. Identify products with appropriate markings of applicable testing agency. 1. Flame-Spread Index: Not greater than Smoke-Developed Index:

6 D. Indoor Environmental Quality Certification: Provide certificate indicated that products have been certified under the following programs, or a comparable certification acceptable to Owner: 1. GREENGUARD Indoor Air Quality Certified Delivery, Storage, And Handling A. Do not deliver toilet compartments to site until building is enclosed and HVAC systems are in operation Warranty 1. Deliver toilet compartments in manufacturer's original packaging. 2. Store in an upright condition. A. Special Manufacturer s Warranty: Provide manufacturer's standard form in which manufacturer agrees to repair or replace products that fail in materials or workmanship during the following period after substantial completion: 05.9 Products Manufacturers 1. Plastic Toilet Partitions: Against corrosion, breakage, and delamination: 15 years. A. Basis-of-Design Manufacturer: Subject to compliance with requirements, provide products of Bradley Corporation, The Mills Company, Menomonee Falls, WI Materials 1. Contact Information: (800) , fax (262) ; Info@BradleyCorp.com; Website A. Plastic Panels: High density polyethylene (HDPE) suitable for exposed applications, waterproof, non-absorbent, and graffiti-resistant textured surface, Class C. B. Provide panels with minimum 30 percent pre-consumer recycled content. C. Zinc Aluminum Magnesium and Copper Alloy (Zamac): ASTM B 86. D. Stainless Steel Sheet: ASTM A 240 or A 666, 300 series. E. Stainless Steel Castings: ASTM A 743/A 743M. F. Aluminum: ASTM B Plastic Toilet Compartments A. Toilet Compartment Type: 1. Overhead braced. 10-6

7 B. Sight Screen Type: a. Basis of Design Product: Bradley, Mills Partitions, No Site Partition System 1. Floor anchored. C. Urinal Screen Style: a. Basis of Design Product: Bradley, Mills Partitions, Floor Braced, with continuous brackets 1. Wall hung with brackets: a. Basis of Design Product: Bradley, Mills Partitions, Wall-Hung with continuous Brackets. D. Door, Panel, and Pilaster Construction, General: HDPE, with a 3/16" (4.8mm) radiused edge. 1. Provide exposed surfaces free of pitting, visible seams and fabrication marks, stains, or other imperfections. 2. Provide aluminum heat sink at bottom edge of panels and doors. E. Provide No Site Partition System F. Door Construction: 1 inch (25 mm) thick. G. Panel Construction: 1 inch (25 mm) thick. H. Pilaster Construction: 1 inch (25 mm) thick. I. Headrail: Extruded anodized aluminum headrail with anti-grip profile. Clamps around pilaster and is secured to the wall with plastic brackets. J. Shoes: 4 inches (76 mm) high minimum, 300 series stainless steel with No. 4 satin brushed finish. K. Urinal-Screen Construction: Matching toilet compartment panel construction L. Brackets (Fittings): 1. Full-Height (Continuous) Type: Manufacturer's standard design; stainless steel. M. Plastic Panel Finish: Manufacturer's standard impregnated finish, with one color in each room Hardware 1. Color: CANTON GRANITE M244 A. Hardware, Heavy Duty: Manufacturer's heavy-duty stainless steel, including stainless steel tamper-resistant fasteners: 10-7

8 1. Hinges: Self-closing integral, nylon, gravity-cam type adjustable to hold doors open at any angle up to 90 degrees, with emergency access by lifting door. 2. Latch and Keeper: Surface-mounted slide latch keeper, with provision for emergency access, meeting requirements for accessibility at accessible compartments. 3. Coat Hook: Combination hook and rubber-tipped stop, sized to prevent door from hitting compartment-mounted accessories. Provide wall bumper where door abuts wall. Provide formed L-shaped hook without stop at outswing doors. Mount with stainless steel through-bolts. 4. Door Pull: Standard unit on outside of inswing doors. Provide pulls on both sides of outswing doors Fabrication Overhead-Braced Units: Provide manufacturer's standard corrosion-resistant supports, leveling mechanism, and anchors at pilasters to suit floor conditions. Provide shoes at pilasters to conceal supports and leveling mechanism. Door Size and Swings: Unless otherwise indicated, provide 26-inch (660-mm) wide, in-swinging doors for standard toilet compartments and 32-inch- (813-mm-) wide, out-swinging doors with a minimum 32- inch- (813-mm-) wide clear opening for compartments designated as accessible. See Architectural drawing for exact door sizes and swings Execution Examination A. Examine work area to verify that measurements, substrates, supports, and environmental conditions are in accordance with manufacturer's requirements to allow installation Installation 1. Proceed with installation once conditions meet manufacturer's requirements. A. General: Comply with manufacturer's written installation instructions. Install units rigid, straight, level, and plumb. Secure units in position with manufacturer's recommended anchoring devices. B. Install toilet partitions and screens in spaces with operating, temperature controlled HVAC systems. Shield partitions and screens from direct sunlight. C. Clearances: Install with clearances indicated on Drawings. Where clearances are not indicated, allow maximum 1/2 inch (13 mm) between pilasters and panels, and 1 inch (25 mm) between panels and walls Adjusting 10-8

9 A. Hardware Adjustment: Adjust and lubricate hardware according to hardware manufacturer's written instructions for proper operation. Set hinges on in-swinging doors to hold doors open approximately 15 degrees from closed position when unlatched. Set hinges on out-swinging doors to return doors to fully closed position Final Cleaning A. Remove packaging and construction debris and legally dispose of off-site. B. Clean partition and screen surfaces with materials and cleansers in accordance with manufacturer's recommendations. Manufacturer Bradley Phone: BRADLEY TOILET ROOM ACCESSORIES Toilet Room Accessories: (General Contractor to install as per Drawings) Manufacturers Bobrick: Bradley: BRADLEY ROLLER SHADE 07.1 Retail Area - Flexshade XD Manual Roller Shade for all Gas Stores as required on drawings. Fabric: SW2710-P28, Openness Factor of 10%, Color: Oyster/Charcoal. Length of shade to center of horizontal mullion. A cord tensioning device must be installed to all looped operating cords. Provide metal covers for rollers to match storefront Office - Flexshade XD Manual Roller Shade as required on drawings. Fabric: SW2701-P28, Openness Factor of 1%.Color: Oyster/Charcoal. Length of shade to top of window sill. A cord tensioning device must be installed to all looped operating cords. Provide metal covers for rollers to match storefront. 10-9

10 07.3 All Shades: Internal hem bar. Clutches, color: Vanilla, with stainless steel chain and child safety tension device, color: Vanilla Manufacturer: Draper Tracy Linville Phone: Alternate Manufacturer Roll-A-Shade Phone: OUTDOOR SHEDS x 7 Shed: Rubbermaid Big Max 1V30, Model # Color: Tan/Brown. See drawings for location x 8' Shed: US Leisure Stonghold 10 ft. x 8 ft. Resin Storage Shed, Model #157479, Color: One color (Brown).See drawings for location. 1. Alternate: Duramax-Woodbridge 10.5 ft. x 8 Vinyl Storage Shed #00211.Model # Color: Beige COAT HOOKS 09.1 General Contractor to provide Coat Hooks on painted wood trim at locations shown on drawings KNOX BOX 10.1 General Contractor to furnish & install Knox-Box. Coordinate location w/ Fire-Marshall in the jurisdiction where the project is located Provide: KNOX-BOX 3200 SERIES END OF SECTION END OF DIVISION 10-10