Pre-Demolition Hazardous Building Materials Survey

Size: px
Start display at page:

Download "Pre-Demolition Hazardous Building Materials Survey"

Transcription

1 Pre-Demolition Hazardous Building Materials Survey Commercial and Residential Property 212 and 210 Street East Peterborough, Ontario K9L 2A3 Presented to: City of Peterborough 500 George Street North Peterborough, Ontario K9H 3R9 May 2014 OHE Project No: Submitted by: Occupational Hygiene & Environment 311 Matheson Blvd Mississauga, Ontario L4Z 1X8 Head Office: 311 Matheson Blvd. East, Mississauga, ON, L4Z 1X8 Tel: Fax: Toll Free: OHE 4 EOH Offices in British Columbia, Alberta, Quebec, Nova Scotia, Ajax, Peterborough

2 TABLE OF CONTENTS 1. INTRODUCTION AND REGULATORY REQUIREMENTS INTRODUCTION AND SCOPE APPLICABLE REGULATIONS AND GUIDELINES Designated Substances Asbestos Lead Silica PCBs METHODOLOGY SURVEY METHODOLOGY METHODOLOGY FOR BULK SAMPLE ANALYSIS METHODOLOGY FOR LEAD ANALYSIS RESULTS FINDINGS ACMS Sprayed Fireproofing Texture Finishes Mechanical Systems Insulation Ceiling Tiles Plaster Materials Vinyl Floor Tiles / Vinyl Sheet Flooring Drywall Joint Compound Roofing Materials Other ACMs LEAD MERCURY SILICA ISOCYANATES VINYL CHLORIDE BENZENE ACRYLONITRILE COKE OVEN EMISSIONS ARSENIC ETHYLENE OXIDE PCBS DISCUSSION ASBESTOS LEAD MERCURY SILICA PCBS RECOMMENDATIONS GENERAL STATEMENT OF LIMITATIONS APPENDIX A: Drawings APPENDIX B: Results of Sampling and Testing for: Asbestos Lead PCBs APPENDIX C: Background Information on Designated Substances APPENDIX D: Laboratory Analysis Report APPENDIX E: Site Photographs

3 EXECUTIVE SUMMARY OHE Project No.: (OHE) was retained by the City of Peterborough to perform a pre-demolition hazardous building materials survey for the residential property and commercial property located at 212 and 210 Street East, Peterborough, Ontario (herein referred to as the Commercial Property and Residential Property, respectively). The field work was carried out on May 6 and May 7, 2014 by Mr. Fahim Hassan, Project Specialist and Mr. Ricardo Romero, Project Consultant, of OHE. The survey consisted of a review of existing environmental reports (where available), visual inspection for the presence of hazardous building materials including designated substances and Polychlorinated Biphenyls (PCBs), and testing and sampling of materials suspected to contain hazardous building materials, particularly asbestos, lead and PCBs. A summary of the hazardous building materials identified during the survey is presented below: Asbestos Asbestos-containing white paper wrap was identified on the ductwork in the basement at the Residential Property. This material is suspected to be present on the ductwork throughout the Residential Property. Asbestos-containing Vinyl Floor Tiles (VFTs) were identified in the kitchen and east washroom at the Residential Property. Asbestos-containing texture coat was identified on the ceiling of the north storage room adjacent to the kitchen and on the ceiling of the entertainment room at the Residential Property. Asbestos-containing heat shield was identified on the light fixture in the entertainment room at the Residential Property. Asbestos-containing window putty was identified on the exterior window frames at the Residential Property. Asbestos-containing white caulking was identified on the exterior window frames at the Residential Property. Asbestos-containing grey caulking was identified on the exterior window frames at the Commercial Property. Asbestos-containing black caulking was identified on the exterior window frames at the Commercial Property. Suspect asbestos-containing electrical wire insulation was observed throughout the Residential Property and Commercial Property. Lead Lead-containing paint was identified in various colours and at various locations at the Residential Property and Commercial Property. A detailed description of the colours and locations is Page i

4 EXECUTIVE SUMMARY OHE Project No.: presented in Table B.2 found in Appendix B. It is assumed that the results presented apply to all paint(s) of the same colour. Lead may be present in wiring connectors and electric cable sheathing. Lead may be present in solder joints on copper piping. Lead is often present in ceramic building products such as floor or wall tiles. Mercury Mercury-containing thermostats were observed in the kitchen at the Residential Property and in the main office area at the Commercial Property during the survey. Mercury is present in fluorescent tubes and may be present as a component in electrical equipment, such as silent, position dependent switches. PCBs Fluorescent light fixtures were observed throughout the Residential Property and Commercial Property during the survey. Eighteen (18) light ballasts were inspected as part of the survey and based on their labels, are not suspected to contain PCBs with the exception of one (1) ballast which based on its label is suspected to contain PCBs. Silica Silica is presumed to be present in materials such as fillers for paints and mastic and in bricks, ceramics, masonry, concrete and mortar. Hazardous building materials may be present in areas not accessible for view and identification. In situations where the hazardous building materials extend into a non-accessible area, the materials were assumed to also be present in those areas and have been reported as such. Contractors and maintenance personnel should be warned of the possibility of undisclosed hazardous building materials when breaking into enclosed areas or concealed wires inside the conduits. All hazardous building materials discovered in these areas should be treated as a hazardous building material until proven otherwise as per all applicable regulation and guidelines. OHE s recommendations, based on the findings of the survey, are as follows: Provide a copy of this report to contractors bidding on or performing work within the Residential Property and Commercial Property; Remove all asbestos-containing materials that are likely to be disturbed during planned renovations or demolition; Page ii

5 EXECUTIVE SUMMARY OHE Project No.: Removal of asbestos-containing white paper wrap will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 2 Operation if < 1 m 2 or Type 3 Operation if > 1 m 2 ); Removal of asbestos-containing VFTs will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 1 Operation); Removal of asbestos-containing texture coat will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 2 Operation if < 1 m 2 or Type 3 Operation if > 1 m 2 ); Removal of asbestos-containing heat shield will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 1 Operation); Removal of the asbestos-containing window putty will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 1 Operation); Removal of the asbestos-containing window caulking will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 1 Operation); Removal of suspect asbestos-containing electrical wire insulation will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 1 Operation); Remove all lead-containing materials that are likely to be disturbed during planned renovations or demolition; Removal of or work with lead-containing materials shall be carried out in accordance with the following requirements: o Guideline: Lead on Construction Projects (issued by Ontario Ministry of Labour); o Ontario Regulation 490/09 Designated Substances (O. Reg. 490/09); and o Ontario Regulation 213/9 Construction Projects (O. Reg. 213/91); Removal of mercury-containing equipment or components shall be carried out in a manner to minimize potential for spills in accordance with the following regulations: o O. Reg. 490/09; and, o O. Reg. 213/91; Renovations and/or demolition operations that are likely to generate silica-containing dust shall be carried out in accordance with the following requirements: o Guideline: Silica on Construction Projects (issued by Ontario Ministry of Labour); o O. Reg. 490/09; and Page iii

6 EXECUTIVE SUMMARY OHE Project No.: o O. Reg. 213/91; Examine all light ballasts after dismantling and prior to disposal to determine their PCB content. PCB-containing light ballasts should be disposed of following procedures specified in applicable regulations; Hazardous materials waste shall be transported and disposed of in accordance with all applicable regulations and guidelines; and Should suspect hazardous materials be discovered during any demolition or renovation work in the above mentioned location, the contractor shall stop all work and immediately notify personnel from both the City of Peterborough and. This executive summary provides a brief overview of the survey findings. It is not intended to substitute for the complete survey report, nor does it discuss specific issues documented in the report. The executive summary should not be used as a substitute to reading the complete report. Page iv

7 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May INTRODUCTION AND REGULATORY REQUIREMENTS 1.1 Introduction and Scope (OHE) was retained by the City of Peterborough to perform a pre-demolition hazardous building materials survey for the residential property and commercial property located at 212 and 210 Street East, Peterborough, Ontario (herein referred to as the Residential Property and Commercial Property, respectively). In accordance with Section 30 of the Ontario Occupational Health and Safety Act, Designated Substances and other potentially hazardous building materials must be identified prior to construction or demolition that may disturb such materials. The Designated Substances include: Asbestos Lead Mercury Silica Isocyanates Vinyl Chloride Benzene Acrylonitrile Coke Oven Emissions Arsenic Ethylene Oxide In addition to Designated Substances, the scope of this survey also included the identification of PCBs, which are subject to Ontario Ministry of Environment regulations. 1.2 Applicable Regulations and Guidelines Designated Substances A Designated Substances report is completed to fulfil the Owner's requirements under Section 30 of the Ontario Occupational Health and Safety Act. A copy of the report must be provided to the general contractor who in turn must submit the report to all subcontractors prior to the commencement of any demolition, construction or renovation work. There are no specific Ministry of Labour regulations for control of the other Designated Substances on construction projects. However, the Ministry of Labour actively enforces the general duty clause of the Health and Safety Act which protects workers and provides guidance on exposure monitoring, permissible exposure levels, medical monitoring, etc. for all Designated Substances in an industrial setting. Page 1

8 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May Asbestos Ontario Regulation 278/05 applies to buildings with regards to maintenance, renovations or demolition work where Asbestos-Containing Materials (ACMs) are or may be disturbed. The major requirements of the asbestos management program for the building owner include: Preparation and maintenance of a record of the location of asbestos-containing materials in the building; Notification of the building's tenants of the location of such material; Establishment of a training program for those employees of the owner who may work in close proximity to and disturb the material; Periodic inspection of the material to determine its condition; Remedial action on material that has deteriorated following the precautions and procedures prescribed by the regulation as Type 1, Type 2 and Type 3; and Removal of asbestos-containing materials to the extent practicable prior to demolition of a building or part thereof. The regulation prescribes work to be conducted according to three procedure types. The procedure to be followed depends on the type of material and the regulation provides instruction on how the work must be performed. Three regulations govern the control, handling, transport and disposal of asbestos in Ontario: Ontario Regulation 278/05, Asbestos on Construction Projects and in Buildings and Repair Operations, made under the Occupational Health and Safety Act (O. Reg. 278/05); Ontario Regulation 347 General-Waste Management (as amended) under the Environmental Protection Act; and The Regulations Respecting the Handling and Offering for Transport and Transporting of Dangerous Goods Lead Guideline: Lead on Construction Projects (issued by Ontario Ministry of Labour) has been prepared to raise the awareness of employers and workers to the hazards posed by lead in construction and the measures and procedures that should be taken to control those hazards. Page 2

9 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May 2014 The document provides information on the following: Health effects associated with lead exposure; Methods for controlling the lead hazard; Classification of work; and, Measure and procedures for working with lead. The guideline classifies operations involving lead-containing materials into three groups, Type 1, Type 2 and Type 3 operations. The procedure to be followed depends on the anticipated airborne concentration of lead generated during the operation, which is dependent on the type of work performed. The guideline also provides instruction on how the work must be performed Silica Guideline: Silica on Construction Projects (issued by Ontario Ministry of Labour) has been prepared to raise the awareness of employers and workers to the hazards posed by silica in construction and the measures and procedures that should be taken to control those hazards. The document provides information on the following: Health effects associated with silica exposure; Methods for controlling the silica hazard; Classification of work; and, Measure and procedures for working with silica. The guideline classifies operations involving silica-containing materials into three groups, Type 1, Type 2 and Type 3 operations. The procedure to be followed depends on the anticipated airborne concentration of silica generated during the operation, which is dependent on the type of work performed. The guideline also provides instruction on how the work must be performed PCBs Ontario Regulation 362, Waste Management-PCBs, made under the Environmental Protection Act, controls the waste management and transfer of PCBs. Page 3

10 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May METHODOLOGY 2.1 Survey Methodology The fieldwork was conducted by Mr. Fahim Hassan, Project Specialist and Mr. Ricardo Romero, Project Consultant, of OHE on May 6 and May 7, Identification of materials suspected of containing hazardous substances was performed by the surveyors who, through their knowledge (from published literature and past experience), were able to identify the potential presence of such materials in buildings. The fieldwork consisted of surveying all accessible areas in order to obtain an overall representation of the hazardous materials present. OHE followed the protocols outlined in O. Reg. 278/05 for collecting and analyzing bulk samples of materials suspected to contain asbestos. Visual assessment of the material was the primary method of identification with occasional physical contact for the purpose of collecting bulk samples or examining for underlying layers. Representative bulk samples were collected of materials suspected of containing asbestos. The tools used by the investigator to collect the bulk samples were cleaned after each sample was collected to avoid cross contamination. Samples were placed in plastic sealable containers, marked with a unique sample number and transported to an independent accredited laboratory for analysis. 2.2 Methodology for Bulk Sample Analysis Bulk samples of suspect ACMs were analyzed in accordance with a US EPA method for the determination of asbestos content in bulk materials, EPA Method 600/R-93/116. The EPA Method requires that the samples be analyzed using the Polarized Light Microscopy (PLM) technique. The percentage of asbestos in the sample is measured as perceived by the analyst in comparison to standard area projections and is greatly influenced by the analyst s experience. The method is useful for the qualitative identification of asbestos (type) and the semi-quantitative (% estimates) determination of asbestos content in bulk samples. The asbestos bulk samples were analyzed by EMSL Analytical, Inc. (EMSL), an independent and NVLAP accredited laboratory. 2.3 Methodology for Lead Analysis Testing for lead in paint was carried out using an X-ray Fluorescence (XRF) Spectrum Analyser. Painted surfaces contain concentrations of various elements which the XRF can detect using lowlevel radioactivity. The XRF unit is positioned against the exposed painted surface and the radiation from the XRF is directed at the painted surface. The radiation is absorbed by the painted Page 4

11 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May 2014 surface and emits energy back to the analyzer as fluorescence. The level of fluorescence will be distinctive to a particular element present in the paint. Lead emissions are measured by the analyzer, and then converted into an electrical signal. The analyzer uses this electric signal to calculate and display the lead concentration in the paint surface. The low levels of radiation provide for accurate readings with the precision of 0.05 mg/cm 2 when measuring lead concentrations. The XRF is equipped with a depth index that indicates where the lead is located within the paint layers. The detection limit of the instrument varies with depth and ranges from mg/cm 2 to 0.05 mg/cm 2. The analyzer used by OHE performs an automatic self-calibration/quality control check when the unit is switched on. 3. RESULTS The results of the survey for asbestos, lead and PCBs are presented in Appendix B. The results are presented in the form of summary tables for each of the materials. Bulk sample locations for suspect ACMs are shown on Drawing 1.1 to 1.8 presented in Appendix A. XRF spot testing locations for lead in paint are shown on Drawing 2.1 to 2.6 presented in Appendix A. The locations of the friable asbestos-containing materials are shown on Drawing 3.1 to 3.2 presented in Appendix A. The locations of the non-friable asbestos-containing materials are shown on Drawing 4.1 to 4.2 presented in Appendix A. The laboratory analysis results are presented in Appendix D. Selected site photographs are shown in Appendix E. 4. FINDINGS 4.1 ACMs Sprayed Fireproofing Sprayed fireproofing was not observed at the Residential Property or the Commercial Property. Page 5

12 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May Texture Finishes Texture Coat Texture finishes were observed on the west wall of the north washroom, ceiling of the north storage room adjacent to the main floor kitchen, west wall of the living room and ceiling of the entertainment room at the Residential Property. Four (4) sample sets, consisting of twelve (12) samples (OHE Samples A to C, A to C, A to C and A to C), of the texture finishes were collected during the survey. OHE Sample A, collected from the ceiling of the north storage room adjacent to the main floor kitchen was found to contain 1% Chrysotile asbestos. OHE Sample A, collected from the ceiling of the entertainment room was found to contain 1% Chrysotile asbestos. The remaining samples in the sample set were not analyzed as per O. Reg. 278/05. Asbestos was not detected in the remaining six (6) samples collected and analyzed Mechanical Systems Insulation White Paper Wrap White paper wrap was observed on the air handling unit in the basement at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the white paper wrap was collected during the survey. OHE Sample A, collected from the basement air handling unit was found to contain 60% Chrysotile asbestos. The remaining samples in the sample set were not analyzed as per O. Reg. 278/05. This material is suspect to be present on the ductwork throughout the Residential Property. Wrap Paper Wrap paper was observed on the pipes around storage tank in the basement at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the wrap paper was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Page 6

13 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May Ceiling Tiles Ceiling tiles were not observed at the Residential Property or the Commercial Property Plaster Materials Plaster Plaster was observed on the walls and the ceilings throughout the Residential Property. Five (5) sample sets, consisting of twenty-nine (29) samples (OHE Samples A to G, A to E, A to G, A to E and A to E), of the plaster were collected during the survey. Asbestos was not detected in the twenty-nine (29) samples collected and analyzed. Cement Parging Cement parging was observed on the exterior walls at the Residential Property. One (1) sample set, consisting of seven (7) samples (OHE Samples A to G), of the cement parging was collected during the survey. Asbestos was not detected in the seven (7) samples collected and analyzed Vinyl Floor Tiles / Vinyl Sheet Flooring Three (3) distinct styles of Vinyl floor tiles (VFTs) were observed in the kitchen, east washroom and west bedroom at the Residential Property. Three (3) sample sets, consisting of nine (9) samples (OHE Samples A to C, A to C and A to C), of the VFTs were collected during the survey. OHE Sample A, collected from the main floor kitchen was found to contain 3% Chrysotile asbestos. The remaining samples in the sample set were not analyzed as per O. Reg. 278/05. Asbestos was not detected in the remaining six (6) samples collected and analyzed. Sixteen (16) distinct types of Vinyl Sheet Flooring (VSF) were observed in various locations at the Residential Property. Sixteen (16) sample sets, consisting of forty-eight (48) samples (OHE Samples A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C and A to C), of the VSF were collected during the survey. Asbestos was not detected in the forty-eight (48) samples collected and analyzed. Page 7

14 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May Drywall Joint Compound Drywall joint compound (DJC) was observed on the walls and the ceiling throughout the Residential Property and the Commercial Property. Seven (7) sample sets, consisting of twentythree (23) samples (OHE Samples A to C, A to E, A to C, A to C, A to C, A to C and A to C), of the DJC were collected during the survey. Asbestos was not detected in the twenty-three (23) samples collected and analyzed Roofing Materials Roof Shingles Roofing materials were observed at the Residential Property and Commercial Property. Twelve (12) sample sets, consisting of thirty six (36) samples (OHE Samples, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C, A to C and A to C), of the roof shingles were collected during the survey. Asbestos was not detected in the thirty six (36) samples collected and analyzed. Roof Felt Roof felt was observed throughout the Residential Property and Commercial Property. Seven (7) sample sets, consisting of twenty-one (21) samples (OHE Samples, A to C, A to C, A to C, A to C, A to C, A to C and A to C), of the roof felt were collected during the survey. Asbestos was not detected in the twenty-one (21) samples collected and analyzed. Black Flashing Black flashing was observed on the roof at the Commercial Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the black flashing was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Page 8

15 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May Other ACMs Yellow Flex Joint Yellow flex joint was observed on the air handling unit in the basement at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the yellow flex joint was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Black Paper Backing Black paper backing was observed underneath the carpet on the staircase leading to the basement at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the black paper backing was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Compressed Board Backing Compressed board backing was observed on the walls throughout the Residential Property. One (1) sample set, consisting of seven (7) samples (OHE Samples A to G), of the compressed board backing was collected during the survey. Asbestos was not detected in the seven (7) samples collected and analyzed. Mastic Black mastic was observed underneath the VFTs in the kitchen at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the black mastic was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Yellow mastic was observed under the carpet in the south section of the main floor at the Commercial Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the yellow mastic was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Tar Paper Tar paper was observed behind the wallpaper in the north storage room adjacent to the kitchen at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples Page 9

16 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May A to C), of the tar paper was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Paper Backing Paper backing was observed above the ceiling wooden panels in the living room at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the paper backing was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Black paper backing was observed on the wall and the ceiling at the Commercial Property. Two (2) sample sets, consisting of six (6) samples (OHE Samples A to C and A to C), of the black paper backing were collected during the survey. Asbestos was not detected in the six (6) samples collected and analyzed. Heat Shield A heat shield was observed on the light fixture in the entertainment room at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the heat shield was collected during the survey. OHE Sample A, collected from the main floor entertainment room was found to contain 80% Chrysotile asbestos. The remaining samples in the sample set were not analyzed as per O. Reg. 278/05. Window Glazing Window glazing was observed on the west window frame in the living room at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the window glazing was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Window Putty Window putty was observed on the exterior window frames at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the window putty was collected during the survey. OHE Sample A, collected from the east exterior window frame was found to contain 1% Chrysotile asbestos. The remaining samples in the sample set were not analyzed as per O. Reg. 278/05. Page 10

17 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May 2014 Caulking Grey caulking was observed on the south exterior door frames at the Residential Property and Commercial Property. Two (2) sample sets, consisting of six (6) samples (OHE Samples A to C and A to C), of the grey caulking were collected during the survey. OHE Sample A, collected from the south door frame of the Commercial Property was found to contain 2% Chrysotile asbestos. The remaining samples in the sample set were not analyzed as per O. Reg. 278/05. Asbestos was not detected in the remaining three (3) samples collected and analyzed. White caulking was observed on the exterior window frames, door frames and siding at the Residential Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the white caulking was collected during the survey. OHE Sample A, collected from the exterior west window frame was found to contain 10% Chrysotile asbestos. The remaining samples in the sample set were not analyzed as per O. Reg. 278/05. Black caulking was observed on the exterior of the window frames at the Commercial Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the black caulking was collected during the survey. OHE Sample A, collected from the north section of the exterior window frame was found to contain 2% Chrysotile asbestos. The remaining samples in the sample set were not analyzed as per O. Reg. 278/05. Levelling Compound Levelling compound was observed on the southeast section of the main floor at the Commercial Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the levelling compound was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Paper Wrap Paper Wrap was observed on the south entrance door at the Commercial Property. One (1) sample set, consisting of three (3) samples (OHE Samples A to C), of the paper wrap was collected during the survey. Asbestos was not detected in the three (3) samples collected and analyzed. Electrical Wire Insulation Electrical wire insulation was observed throughout the Residential Property and Commercial Property. Samples were not collected due to the live electrical system within the properties. The Page 11

18 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May 2014 electrical wire insulation is assumed to be asbestos-containing until sampling and analysis proves otherwise. 4.2 Lead Lead-containing paint was identified in various colours and at various locations at the Residential Property and Commercial Property. A detailed description of the colours and locations is presented in Table B.2 found in Appendix B. It is assumed that the results presented apply to all paint(s) of the same colour. Lead may be present in wiring connectors and electric cable sheathing. Lead may be present in solder joints on copper piping. Lead is often present in ceramic building products such as floor or wall tiles. No special handling or disposal procedures are required for this material. Workers performing demolition or alterations to these tiles should be informed of the potential for lead to be present. 4.3 Mercury Mercury-containing thermostats were observed in the kitchen at the Residential Property and in the main office area at the Commercial Property during the survey. Mercury is present in fluorescent tubes and may be present as a component in electrical equipment, such as silent, position dependent switches. 4.4 Silica Silica is presumed to be present in materials such as fillers for paints and mastic and in brick, concrete and mortar. 4.5 Isocyanates The material was not identified during the site visit and is not expected to be found. 4.6 Vinyl Chloride The material was not identified during the site visit and is not expected to be found. Page 12

19 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May Benzene The material was not identified during the site visit and is not expected to be found. 4.8 Acrylonitrile The material was not identified during the site visit and is not expected to be found. 4.9 Coke Oven Emissions The material was not identified during the site visit and is not expected to be found Arsenic The material was not identified during the site visit and is not expected to be found Ethylene Oxide The material was not identified during the site visit and is not expected to be found PCBs Fluorescent light fixtures were observed throughout the Residential Property and Commercial Property during the survey. Eighteen (18) light ballasts were inspected as part of the survey and based on their labels, are not suspected to contain PCBs with the exception of one (1) ballast which based on its label is suspected to contain PCBs. 5. DISCUSSION 5.1 Asbestos Prior to disturbance of ACMs, the materials should be removed using the appropriate type of asbestos removal operation as per O. Reg. 278/ Lead Prior to disturbance of lead-containing materials, the material should be removed using the appropriate type of removal operation as specified in the applicable guidelines and regulations. Page 13

20 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May Mercury Prior to the disturbance of mercury-containing materials, the materials should be removed using applicable guidelines and regulations. Simple personal hygiene practices will be sufficient to protect workers from possible mercury exposure. 5.4 Silica Silica-containing materials should be handled using the appropriate type of operation as specified in the applicable guidelines and regulations. No adverse effects from exposure to silica are likely to occur unless silica in the material is reduced to a respirable size and the airborne concentrations exceed the 8-hour time-weighted average. 5.5 PCBs Prior to the disturbance of PCB-containing materials, the materials should be removed using applicable guidelines and regulations. Hazardous building materials may be present in areas not accessible for view and identification. In situations where the hazardous building materials extend into a nonaccessible area, the materials were assumed to also be present in those areas and have been reported as such. Contractors and maintenance personnel should be warned of the possibility of undisclosed hazardous building materials when breaking into enclosed areas or concealed wires inside the conduits. All hazardous building materials discovered in these areas should be treated as a hazardous building material until proven otherwise as per all applicable regulation and guidelines. 6. RECOMMENDATIONS OHE s recommendations, based on the findings of the survey, are as follows: Provide a copy of this report to contractors bidding on or performing work within the Residential Property and Commercial Property; Remove all ACMs that are likely to be disturbed during planned renovations or demolition; Removal of asbestos-containing white paper wrap will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 2 Operation if < 1 m2 or Type 3 Operation if > 1 m2); Page 14

21 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May 2014 Removal of asbestos-containing VFTs will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 1 Operation); Removal of asbestos-containing texture coat will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 2 Operation if < 1 m2 or Type 3 Operation if > 1 m2); Removal of asbestos-containing heat shield will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 1 Operation); Removal of the asbestos-containing window putty will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 1 Operation); Removal of the asbestos-containing window caulking will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 1 Operation); Removal of suspect asbestos-containing electrical wire insulation will require removal operation procedures as specified in Ontario Regulation 278/05 (Type 1 Operation); Remove all lead-containing materials that are likely to be disturbed during planned renovations or demolition; Removal of or work with lead-containing materials shall be carried out in accordance with the following requirements: o Guideline: Lead on Construction Projects (issued by Ontario Ministry of Labour); o Designated Substances Regulation, O. Reg. 490/09; and o Regulation for Construction Projects, O. Reg. 213/91; Removal of mercury-containing equipment or components shall be carried out in a manner to minimize potential for spills in accordance with the following regulations: o Designated Substances Regulation, Ontario Regulation 490/09; and, o Regulation for Construction Projects, Ontario Regulation 213/91; Renovations and/or demolition operations that are likely to generate silica-containing dust shall be carried out in accordance with the following requirements: o Guideline: Silica on Construction Projects (issued by Ontario Ministry of Labour); o Designated Substances Regulation, O. Reg. 490/09; and o Regulation for Construction Projects, O. Reg. 213/91; Page 15

22 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May 2014 Examine all light ballasts after dismantling and prior to disposal to determine their PCB content. PCB-containing light ballasts should be disposed of following procedures specified in applicable regulations; Hazardous materials waste shall be transported and disposed of in accordance with all applicable regulations and guidelines; and Should suspect hazardous materials be discovered during any demolition or renovation work in the Residential Property and Commercial Property, the contractor shall stop all work and immediately notify personnel from both the City of Peterborough and OHE Consultants. Page 16

23 Pre-Demolition Hazardous Building Materials Survey Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: May GENERAL STATEMENT OF LIMITATIONS The information and opinions rendered in this report are for use exclusively by the City of Peterborough. OHE reserves the right to review and comment on any interpretation of the data or conclusions derived by the City of Peterborough. No other representation, either expressed or implied, is included in this report. The survey did not consider current or past use of the property or occupant articles within the building (i.e. furniture, stock items, etc.), nor does it report on possible contaminants in the soil and groundwater of the site, vessels, drums, underground storage tanks, etc. The survey consisted of accessible areas only; samples were not collected if accessibility was restricted. The field observations and analysis are considered sufficient in detail and scope to form a reasonable basis for the findings presented in this report. OHE warrants that the findings and conclusions contained herein have been made in accordance with generally accepted evaluation methods in the industry and applicable regulations at the time of the performance of the survey. It is possible, due to the nature of building construction, that conditions may exist which could not be reasonably identified within the scope of the survey or which were not apparent during the site investigation. OHE believes that the information collected during the survey period concerning the property is reliable. No other warranties are implied or expressed. Dated May 2014 Occupational Hygiene & Environment Digitally signed by Ricardo Romero DN: cn=ricardo Romero, o=, ou, =rromero@ohecon sultants.com, c=ca Prepared by: Ricardo Romero, CHSO Project Consultant Digitally signed by Kelly Fernandes DN: cn=kelly Fernandes, o=.com, ou, =kfernandes@ohec onsultants.com, c=ca Reviewed by: Kelly Fernandes, M.Sc., EP, CIH. Senior Technical Reviewer/Occupational Hygienist Digitally signed by Farid Atrash DN: cn=farid Atrash, o=, ou, =fred@oheconsult ants.com, c=ca Reviewed by: Fred Atrash, M.H.Sc., ROH, CIH Director/Senior Consultant Page 17

24 APPENDIX A DRAWINGS

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43 APPENDIX B RESULTS OF SAMPLING AND TESTING FOR: Asbestos Lead PCBs

44 Table B.1 Summary of Bulk Samples Analysis Results for the Presence of Asbestos by Polarized Light Microscopy (PLM) with Dispersion Staining Collected on May 6 and May 7, 2014 OHE Sample Number Sample Description A Plaster Wall (Interior) B Plaster Wall (Interior) C Plaster Wall (Interior) D Plaster Wall (Interior) E Plaster Wall (Interior) F Plaster Wall (Interior) G Plaster Wall (Interior) A Yellow Flex Joint B Yellow Flex Joint C Yellow Flex Joint A White Paper Wrap B White Paper Wrap C White Paper Wrap A B C Black Paper Backing Underneath Carpet Black Paper Backing Underneath Carpet Black Paper Backing Underneath Carpet A Plaster Ceiling B Plaster Ceiling C Plaster Ceiling D Plaster Ceiling E Plaster Ceiling A Plaster Wall (Exterior) B Plaster Wall (Exterior) Sample Location Basement, West Wall of Staircase, Main Floor, Kitchen, South Wall, Main Floor, North Washroom Adjacent to Kitchen, East Wall, Main Floor, Living Room, West Wall, Main Floor, Entertainment Room, East Wall, Main Floor, South Vestibule Area, East Wall, Main Floor, South Vestibule Area, West Wall, Basement, Air Handling Unit, 212 Basement, Air Handling Unit, 212 Basement, Air Handling Unit, 212 Basement, Air Handling Unit, Basement, Air Handling Unit, Basement, Air Handling Unit, Basement, Staircase, 212 Basement, Staircase, 212 Basement, Staircase, 212 Main Floor, Kitchen, 212 Main Floor, North Washroom Adjacent to Kitchen, 212 Main Floor, Living Room Above Wooden Joists, Main Floor, Entertainment Room, Northeast Section, 212 Main Floor, Entertainment Room, Southwest Section, 212 Main Floor, Living Room, South Wall, Main Floor, Living Room, West Wall, Analysis Results (% and Type of Asbestos) 60% Chrysotile Stop Positive (Not Analyzed) Stop Positive (Not Analyzed)

45 Table B.1 Continued OHE Sample Number Sample Description C Plaster Wall (Exterior) D Plaster Wall (Exterior) E Plaster Wall (Exterior) F Plaster Wall (Exterior) G Plaster Wall (Exterior) A Compressed Board Backing B Compressed Board Backing C Compressed Board Backing D Compressed Board Backing E Compressed Board Backing F Compressed Board Backing G Compressed Board Backing A B C Vinyl Floor Tile (VFT) 1-12 x12 - White with Stone Patterns Vinyl Floor Tile (VFT) 1-12 x12 - White with Stone Patterns Vinyl Floor Tile (VFT) 1-12 x12 - White with Stone Patterns A Black Mastic underneath VFT B Black Mastic underneath VFT C Black Mastic underneath VFT A B C A-Floor Tile Vinyl Sheet Flooring (VSF) 1 Brown Ceramic Pattern Vinyl Sheet Flooring (VSF) 1 Brown Ceramic Pattern Vinyl Sheet Flooring (VSF) 1 Brown Ceramic Pattern VSF 2 Yellowish Blue with Yellow Mastic Sample Location Main Floor, Entertainment Room, South Wall, Main Floor, Entertainment Room, East Wall, 2 nd Floor, Northeast Room, East Wall, 2 nd Floor, East Room, East Wall, 2 nd Floor, West Room, West Wall, Main Floor, Kitchen, South Wall, Main Floor, Living Room, South Wall, Main Floor, Living Room, East Wall, Main Floor, Entertainment Room, East Wall, Main Floor, North Washroom Adjacent to Kitchen, West Wall, Main Floor, South Vestibule Area, Underneath Staircase, East Wall, 2 nd Floor, West Room, East Wall, Main Floor, Kitchen, 212 Main Floor, Kitchen, 212 Main Floor, East Washroom, Main Floor, Kitchen, 212 Main Floor, Kitchen, 212 Main Floor, Kitchen, 212 Main Floor, North Washroom Adjacent to Kitchen, 212 Main Floor, North Washroom Adjacent to Kitchen, 212 Basement, Kitchen, Main Floor, North Washroom Adjacent to Kitchen, 212 Basement, Kitchen, Main Floor, North Washroom Adjacent to Kitchen, 212 Analysis Results (% and Type of Asbestos) 3% Chrysotile Stop Positive (Not Analyzed) Stop Positive (Not Analyzed)

46 Table B.1 Continued OHE Sample Number A-Mastic B-Floor Tile B-Mastic C-Floor Tile C-Mastic Sample Description VSF 2 Yellowish Blue with Yellow Mastic VSF 2 Yellowish Blue with Yellow Mastic VSF 2 Yellowish Blue with Yellow Mastic VSF 2 Yellowish Blue with Yellow Mastic VSF 2 Yellowish Blue with Yellow Mastic A Texture Coat B Texture Coat C Texture Coat A Drywall Joint Compound (DJC) B Drywall Joint Compound (DJC) C Drywall Joint Compound (DJC) A Texture Coat B Texture Coat C Texture Coat A Tar Paper Behind Wall Paper B Tar Paper Behind Wall Paper C Tar Paper Behind Wall Paper A VSF 3 Faded Blue B VSF 3 Faded Blue Sample Location Main Floor, North Washroom Adjacent to Kitchen, 212 Main Floor, North Washroom Adjacent to Kitchen, 212 Main Floor, North Washroom Adjacent to Kitchen, 212 Main Floor, North Washroom Adjacent to Kitchen, 212 Main Floor, North Washroom Adjacent to Kitchen, 212 Main Floor, North Washroom Adjacent to Kitchen, West Wall, Main Floor, North Washroom Adjacent to Kitchen, West Wall, Main Floor, North Washroom Adjacent to Kitchen, West Wall, Main Floor, North Washroom Adjacent to Kitchen, Around Pipe Penetration, Main Floor, North Washroom Adjacent to Kitchen, Around Pipe Penetration, Main Floor, North Washroom Adjacent to Kitchen, Around Pipe Penetration, Main Floor, North Storage Room Adjacent to Kitchen, Ceiling, Main Floor, North Storage Room Adjacent to Kitchen, Ceiling, Main Floor, North Storage Room Adjacent to Kitchen, Ceiling, Main Floor, North Storage Room Adjacent to Kitchen, South Wall, Main Floor, North Storage Room Adjacent to Kitchen, East Wall, Main Floor, North Storage Room Adjacent to Kitchen, West Wall, Main Floor, North Storage Room Adjacent to Kitchen, 212 Main Floor, North Storage Room Adjacent to Kitchen, 212 Analysis Results (% and Type of Asbestos) 1% Chrysotile Stop Positive (Not Analyzed) Stop Positive (Not Analyzed)

47 Table B.1 Continued OHE Sample Number Sample Description C VSF 3 Faded Blue A B C A B C VSF 4 Red and Green Flower Pattern VSF 4 Red and Green Flower Pattern VSF 4 Red and Green Flower Pattern VSF 5 Grey with White and Dark Grey Spots VSF 5 Grey with White and Dark Grey Spots VSF 5 Grey with White and Dark Grey Spots A Texture Coat B Texture Coat C Texture Coat A DJC B DJC C DJC D DJC E DJC A B C Paper Backing Above Wooden Panels Paper Backing Above Wooden Panels Paper Backing Above Wooden Panels A Heat Shield B Heat Shield C Heat Shield A B C A VSF 6 Brown with Light Beige and White Pattern VSF 6 Brown with Light Beige and White Pattern VSF 6 Brown with Light Beige and White Pattern VSF 7 Dark Green Flower Pattern Sample Location Main Floor, North Storage Room Adjacent to Kitchen, 212 Main Floor, North Storage Room Adjacent to Kitchen, 212 Main Floor, North Storage Room Adjacent to Kitchen, 212 Main Floor, North Storage Room Adjacent to Kitchen, 212 Main Floor, Living Room, 212 Main Floor, Living Room, 212 Main Floor, Living Room, 212 Main Floor, Living Room, West Wall, Main Floor, Living Room, West Wall, Main Floor, Living Room, South Wall, Main Floor, Living Room, West Wall, Main Floor, Living Room, South Wall, Main Floor, Living Room, South Wall, Main Floor, Entertainment Room, North Wall, Above Door Frame, Main Floor, Entertainment Room, South Wall, Above Window Frame, Main Floor, Living Room, 212 Main Floor, Living Room, 212 Main Floor, Living Room, 212 Main Floor, Entertainment Room, Main Floor, Entertainment Room, Main Floor, Entertainment Room, Main Floor, Entertainment Room, Main Floor, Entertainment Room, Main Floor, Entertainment Room, Main Floor, Entertainment Room, Analysis Results (% and Type of Asbestos) 80% Chrysotile Stop Positive (Not Analyzed) Stop Positive (Not Analyzed)

48 Table B.1 Continued OHE Sample Number B C Sample Description VSF 7 Dark Green Flower Pattern VSF 7 Dark Green Flower Pattern A Texture Coat B Texture Coat C Texture Coat A B C A B C VSF 8 Yellow with Black Pattern VSF 8 Yellow with Black Pattern VSF 8 Yellow with Black Pattern VSF 9 Beige with Light Beige and Brown Pattern VSF 9 Beige with Light Beige and Brown Pattern VSF 9 Beige with Light Beige and Brown Pattern A Insulation Wrap Paper B Insulation Wrap Paper C Insulation Wrap Paper A B C VSF 10 Black and White Square Pattern VSF 10 Black and White Square Pattern VSF 10 Black and White Square Pattern A VSF 11 Red Flower Pattern B VSF 11 Red Flower Pattern C VSF 11 Red Flower Pattern A B C VSF 12 Blue Diagonal Streak Pattern VSF 12 Blue Diagonal Streak Pattern VSF 12 Blue Diagonal Streak Pattern A VSF 13 Black Flower Pattern B VSF 13 Black Flower Pattern C VSF 13 Black Flower Pattern A VFT 2 12 x12 - Light Grey B VFT 2 12 x12 - Light Grey Sample Location Main Floor, Entertainment Room, Main Floor, Entertainment Room, Main Floor, Entertainment Room, Ceiling, Main Floor, Entertainment Room, Ceiling, Main Floor, Entertainment Room, Ceiling, Main Floor, North Vestibule Area, Main Floor, North Vestibule Area, Main Floor, North Vestibule Area, Main Floor, North Vestibule Area, Main Floor, North Vestibule Area, Main Floor, North Vestibule Area, Basement, Pipes around Storage Tank, Basement, Pipes around Storage Tank, Basement, Pipes around Storage Tank, 2 nd Floor, South Storage Room, 2 nd Floor, South Storage Room, 2 nd Floor, Adjacent to Staircase, 2 nd Floor, Northeast Room, nd Floor, Northeast Room, nd Floor, Northeast Room, nd Floor, East Room, nd Floor, East Room, nd Floor, East Room, nd Floor, East Room, nd Floor, East Room, nd Floor, East Room, nd Floor, West Room, nd Floor, West Room, 212 Analysis Results (% and Type of Asbestos) 1% Chrysotile Stop Positive (Not Analyzed) Stop Positive (Not Analyzed)

49 Table B.1 Continued OHE Sample Number Sample Description C VFT 2 12 x12 - Light Grey A B C VFT 3 12 x12 - Brown with Grey Stone Pattern VFT 3 12 x12 - Brown with Grey Stone Pattern VFT 3 12 x12 - Brown with Grey Stone Pattern A Plaster Wall (Interior) B Plaster Wall (Interior) C Plaster Wall (Interior) D Plaster Wall (Interior) E Plaster Wall (Interior) A Plaster Ceiling B Plaster Ceiling C Plaster Ceiling D Plaster Ceiling E Plaster Ceiling A VSF 14 Blue Flower Pattern B VSF 14 Blue Flower Pattern C VSF 14 Blue Flower Pattern A Cement Parging B Cement Parging C Cement Parging D Cement Parging E Cement Parging F Cement Parging G Cement Parging A Window Glazing B Window Glazing Sample Location 2 nd Floor, West Room, nd Floor, West Room, nd Floor, West Room, nd Floor, West Room, nd Floor, South Storage Room, South Wall, 2 nd Floor, Northeast Room, East Wall, 2 nd Floor, East Room, North Wall, 2 nd Floor, West Room, South Wall, 2 nd Floor, Staircase, East Wall, 2 nd Floor, South Storage Room, 2 nd Floor, Northeast Room, nd Floor, East Room, nd Floor, West Room, nd Floor, Adjacent to Staircase, 2 nd Floor, Northeast Room, nd Floor, Northeast Room, nd Floor, East Room, 212 North Exterior Wall, 212 North Exterior Wall, 212 West Exterior Wall, 212 West Exterior Wall, 212 West Exterior Wall, 212 South Exterior Wall, 212 East Exterior Wall, 212 Interior, Window Frame, Living Room, West Wall, 212 Interior, Window Frame, Living Room, West Wall, 212 Analysis Results (% and Type of Asbestos)

50 Table B.1 Continued OHE Sample Number Sample Description C Window Glazing A Window Putty B Window Putty C Window Putty A Grey Caulking B Grey Caulking C Grey Caulking A White Caulking B White Caulking C White Caulking A B C A B C VSF 15 Green with Small Dots of Yellow and Red Flower VSF 15 Green with Small Dots of Yellow and Red Flower VSF 15 Green with Small Dots of Yellow and Red Flower VSF 16 Light Brown with Green, Red and Brown Squares VSF 16 Light Brown with Green, Red and Brown Squares VSF 16 Light Brown with Green, Red and Brown Squares A Top Layer Shingle B Top Layer Shingle C Top Layer Shingle A Top Layer Shingle B Top Layer Shingle C Top Layer Shingle A Top Layer Shingle B Top Layer Shingle C Top Layer Shingle A Top Layer Shingle Sample Location Interior, Window Frame, Living Room, West Wall, 212 Exterior, East Window Frame Adjacent to North Entrance, Exterior, East Window Frame Adjacent to North Entrance, Exterior, West Window Frame Adjacent to North Entrance, Exterior, South Entrance Door Frame, Exterior, South Entrance Door Frame, Exterior, South Entrance Door Frame, Exterior, West Window Frame, Exterior, West Door Frame, 212 Exterior, West Siding, nd Floor, East Room, nd Floor, East Room, nd Floor, East Room, nd Floor, South Storage Room, 2 nd Floor, South Storage Room, 2 nd Floor, South Storage Room, North Roof, East Section, 212 North Roof, Middle Section, 212 North Roof, West Section, 212 East Roof, North Section, 212 East Roof, Middle Section, 212 East Roof, South Section, 212 South Main Roof, East Section, South Main Roof, Middle Section, South Main Roof, West Section, South Entrance Roof, East Section, Analysis Results (% and Type of Asbestos) 1% Chrysotile Stop Positive (Not Analyzed) Stop Positive (Not Analyzed) 10% Chrysotile Stop Positive (Not Analyzed) Stop Positive (Not Analyzed)

51 Table B.1 Continued OHE Sample Number Sample Description B Top Layer Shingle C Top Layer Shingle A Bottom Layer Shingle B Bottom Layer Shingle C Bottom Layer Shingle A Bottom Layer Shingle B Bottom Layer Shingle C Bottom Layer Shingle A Bottom Layer Shingle B Bottom Layer Shingle C Bottom Layer Shingle A Bottom Layer Shingle B Bottom Layer Shingle C Bottom Layer Shingle A Roof Felt B Roof Felt C Roof Felt A Roof Felt B Roof Felt C Roof Felt A Roof Felt B Roof Felt C Roof Felt A Roof Felt B Roof Felt C Roof Felt A DJC B DJC Sample Location South Entrance Roof, Middle Section, South Entrance Roof, West Section, North Roof, East Section, 212 North Roof, Middle Section, 212 North Roof, West Section, 212 East Roof, North Section, 212 East Roof, Middle Section, 212 East Roof, South Section, 212 South Main Roof, East Section, South Main Roof, Middle Section, South Main Roof, West Section, South Entrance Roof, East Section, South Entrance Roof, Middle Section, South Entrance Roof, West Section, North Roof, East Section, 212 North Roof, Middle Section, 212 North Roof, West Section, 212 East Roof, North Section, 212 East Roof, Middle Section, 212 East Roof, South Section, 212 South Main Roof, East Section, South Main Roof, Middle Section, South Main Roof, West Section, South Entrance Roof, East Section, South Entrance Roof, Middle Section, South Entrance Roof, West Section, Ceiling, 2 nd Floor, North Section, 210 Ceiling, 2 nd Floor, Middle Section, 210 Analysis Results (% and Type of Asbestos)

52 Table B.1 Continued OHE Sample Number Sample Description C DJC A DJC B DJC C DJC A Black Paper Backing B Black Paper Backing C Black Paper Backing A DJC B DJC C DJC A Black Paper Backing B Black Paper Backing C Black Paper Backing A DJC B DJC C DJC A DJC B DJC C DJC A B C Yellow Mastic Underneath Carpet Yellow Mastic Underneath Carpet Yellow Mastic Underneath Carpet A Leveling Compound B Leveling Compound C Leveling Compound A Black Caulking B Black Caulking C Black Caulking Sample Location Ceiling, 2 nd Floor, South Section, 210 North Wall, 2 nd Floor, 210 East Wall, 2 nd Floor, 210 South Wall, 2 nd Floor, 210 North Wall, 2 nd Floor, 210 East Wall, 2 nd Floor, 210 South Wall, 2 nd Floor, 210 Ceiling, Main Floor, North Section, 210 Ceiling, Main Floor, Middle Section, 210 Ceiling, Main Floor, South Section, 210 Ceiling, Main Floor, North Section, 210 Ceiling, Main Floor, Middle Section, 210 Ceiling, Main Floor, South Section, 210 North Wall, Main Floor, 210 East Wall, Main Floor, 210 South Wall, Main Floor, 210 Column, South Section, Main Floor, 210 Column, South Section, Main Floor, 210 Column, South Section, Main Floor, 210 South Section, Main Floor, 210 South Section, Main Floor, 210 South Section, Main Floor, 210 Southeast Section, Main Floor, 210 Southeast Section, Main Floor, 210 Southeast Section, Main Floor, 210 Window Frames, North Section, Exterior, 210 Window Frames, East Section, Exterior, 210 Window Frames, South Section, Exterior, 210 Analysis Results (% and Type of Asbestos) 2% Chrysotile Stop Positive (Not Analyzed) Stop Positive (Not Analyzed)

53 Table B.1 Continued OHE Sample Number Sample Description A Grey Caulking B Grey Caulking C Grey Caulking A Black Flashing B Black Flashing C Black Flashing A Roof Felt B Roof Felt C Roof Felt A Roof Shingles B Roof Shingles C Roof Shingles A Roof Shingles B Roof Shingles C Roof Shingles A Roof Felt B Roof Felt C Roof Felt A Roof Shingles B Roof Shingles C Roof Shingles A Roof Felt B Roof Felt C Roof Felt A Roof Shingles B Roof Shingles C Roof Shingles Sample Location South Door Frame, Exterior, 210 South Door Frame, Exterior, 210 South Door Frame, Exterior, 210 East Side Roof, Exterior, 210 East Side Roof, Exterior, 210 East Side Roof, Exterior, 210 Lower Roof, North Section, Exterior, 210 Lower Roof, Middle Section, Exterior, 210 Lower Roof, South Section Exterior, 210 Main Roof, North Section Exterior, 210 Main Roof, Middle Section, Exterior, 210 Main Roof, South Section Exterior, 210 North Shed Roof, North Section, Exterior North Shed Roof, Middle Section, Exterior North Shed Roof, South Section, Exterior North Shed Roof, North Section, Exterior North Shed Roof, Middle Section, Exterior North Shed Roof, South Section, Exterior Middle Shed Roof, North Section, Exterior Middle Shed Roof, Middle Section, Exterior Middle Shed Roof, South Section, Exterior Middle Shed Roof, North Section, Exterior Middle Shed Roof, Middle Section, Exterior Middle Shed Roof, South Section, Exterior South Shed Roof, North Section, Exterior South Shed Roof, Middle Section, Exterior South Shed Roof, South Section, Exterior Analysis Results (% and Type of Asbestos) 2% Chrysotile Stop Positive (Not Analyzed) Stop Positive (Not Analyzed)

54 OHE Sample Number Sample Description Table B.1 Continued Sample Location Analysis Results (% and Type of Asbestos) A Paper Wrap South Entrance, B Paper Wrap South Entrance, C Paper Wrap South Entrance, 210 Table B.2 Summary of Analysis of Lead in Paint OHE Sample Number Sample Description Sample Location Contains Lead Yes/No L1 White Paint L2 Yellow Paint L3 Yellow Paint L4 Black Paint L5 Wallpaper L6 Light Green Paint L7 Wallpaper L8 Blue Paint L9 Blue Paint L10 Off-White Paint L11 Olive Green Paint L12 Green Wallpaper L13 Light Green Paint West Wall, Basement, South Wall, Kitchen, Main Floor, 212 North Wall, North Storage Room, Main Floor, South Wall, North Storage Room, Main Floor, South Wall, North Storage Room, Main Floor, South Wall, Living Room, Main Floor, 212 West Wall, Living Room, Main Floor, 212 West Wall, Entertainment Room, Main Floor, 212 East Wall, Entertainment Room, Main Floor, 212 Ceiling, North Vestibule Area, Main Floor, West Wall, South Vestibule Area, Main Floor, East Wall, South Vestibule Area, Main Floor, East Wall, South Vestibule Area, Main Floor, No No

55 Table B.2 (Continued) OHE Sample Number Sample Description Sample Location Contains Lead Yes/No L14 Neon Light Blue Paint L15 Light Blue Paint L16 Blue Paint L17 Light Blue Paint L18 White Paint L19 White Paint L20 White Paint L21 Green Paint L22 Light Green Paint L23 Beige Paint L24 Yellow Paint L25 Brown Paint L26 Beige Paint L27 Red Paint L28 Dark Brown Paint L29 Green Paint L30 Beige Paint L31 Dark Brown Paint L32 Blue Paint L33 White Paint South Wall, South Vestibule Area, 2 nd Floor, East Wall, Northeast Room, 2 nd Floor, 212 East Wall, East Room, 2 nd Floor, 212 Ceiling, East Room, 2 nd Floor, South Wall, West Room, 2 nd Floor, 212 South Wall, West Room, 2 nd Floor, 212 Window Frame, East Room, 2 nd Floor, 212 Window Frame, East Room, 2 nd Floor, 212 Baseboard South Vestibule Area, Main Floor, North Wall, Kitchen; adjacent to Washroom, Main Floor, 212 Door Frame, East Washroom in North Vestibule Area, Main Floor, Door Frame, South Vestibule Area, Main Floor, Door Frame, North Vestibule Area, Main Floor, Brick Floor, North Porch, Main Floor, 212 North Exterior Wall, 212 Exterior Window Frame, Exterior Window Frame, Exterior Wood Siding, West Wall, 2 nd Floor, 210 East Wall, 2 nd Floor, No No No No No

56 Table B.2 (Continued) OHE Sample Number Sample Description Sample Location Contains Lead Yes/No L34 Grey Paint L35 Grey Paint L36 White Paint L37 White Paint L38 White Paint L39 Grey Paint L40 Grey Paint L41 Neon Green Paint L42 Grey Paint L43 Light Green Paint L44 Beige Paint L45 Brown Paint L46 Brown Paint L47 White Paint L48 Beige Paint L49 Yellow Paint L50 Yellow Paint Door to Stairwell, 2 nd Floor, 210 Door Frame to Stairwell, 210 East Window Frame, 2 nd Floor, 210 East Wall, Main Floor, 210 Ceiling, South Section, Main Floor, 210 West Window Frame, North Section, Main Floor, 210 Door, North Exit, Main Floor, 210 Cabinets, North Section, Main Floor, 210 Cabinets, North Section, Main Floor, 210 East Window Frame, Main Floor, 210 East Entrance Door, Main Floor, 210 East Structural Column, 210 East Wall, Exterior, 210 East Window Frame, 210 North Window Frame, 210 North Exterior Wall, 210 East Exterior Wall, Middle Shed No No No 0.02 No Note: Classification of lead results is based on the actual XRF readings. Positive results are expressed as the actual concentration of the lead in the paint (mg/cm 2 ). Negative results are expressed as No and are indicative of lead concentration below the limit of detection of the XRF.

57 Table B.3 Summary of the Visual Inspection of the Light Ballasts for PCBs Content Manufacturer Philips Cat. No. R-2C34-TPC Advance Cat. No. R-2E75-S-TPC Philips Cat. No. SM-2E75-S-TPC Alliance Cat. No. 17A297EW Quantity Verified Philips Cat. No. R-2E75-S-TPC 2 Canadian GE Electric Cat. No. 17A297TW 2 Sylvania Cat. No. MB2x96/120 IS Location North Vestibule Area, Street East Upholstery Work Area, 210 Street East Upholstery Work Area, 210 Street East Upholstery Work Area, 210 Street East Main Office Area, 210 Street East Main Office Area, 210 Street East Main Office Area, 210 Street East Markings Labeled Labeled Labeled Labeled Labeled Labeled Labeled Containing PCBs No No No No No Suspect No

58 APPENDIX C BACKGROUND INFORMATION ON DESIGNATED SUBSTANCES

59 ASBESTOS Asbestos is a naturally occurring mineral. Asbestos is divided into two mineral groups: Serpentine and Amphibole. The division between the two types of asbestos is based upon the crystalline structure. The fibers of asbestos are long and thin, easily distinguishable when compared with non-asbestos minerals. The construction industry has been using asbestos for many years because of the ability of asbestos to withstand high temperatures as well as its strength and resistance to corrosive chemicals. When asbestos-containing material is disturbed dust is released into the air that contains asbestos fibers that have the potential to be inhaled into the lungs. Depending on the size of the individual fibers inhaled, some fibers can make their way deep into the air sacs (alveoli) of the lungs. Exposure to asbestos fibers may result in scarring of the lung tissue (asbestosis), cancer of the chest cavity (mesothelioma) or other asbestos related cancers. ACRYLONITRILE Acrylonitrile is explosive, flammable and toxic, found as a colorless or yellow clear liquid. It is used to produce a variety of products including plastics, adhesives, gaskets, seals and hoses. Health effects resulting in acute exposure to acrylonitrile vary from minor symptoms such as eye irritation, itching skin, blisters, headaches, sneezing and vomiting. Chronic exposure may cause cancers of the stomach, lymph system and brain. ARSENIC The common form of arsenic is grey in color with a metallic appearance. Arsenic has been used in the manufacturing of glass to eliminate the green color resulting from the impurities of iron compounds. It was also used in the productions of poisons. Arsenic is poisonous in doses significantly larger than 65 mg (1 grain), and poisoning can arise from a single large dose or from repeated small doses. BENZENE Benzene is an aromatic organic hydrocarbon existing either as a clear liquid or a vapour. Benzene is highly flammable and volatile material and was primarily a by-product in petroleum refineries. However, it has also been commonly used to produce styrene, synthetic rubbers, plastics, resins and solvents. Serious health effects can occur from exposure to benzene, mainly as a result of inhalation of vapours and mists. Ingestion by swallowing and absorption through the skin are also possible routes of exposure. Health effects can result from ingesting food or drink contaminated with benzene. Symptoms can range from irritated eyes, red blistering skin, headaches, nausea and drowsiness. Benzene exposure can also induce blood and bone marrow toxicity. Page 1

60 COKE OVEN EMISSIONS Coke oven emissions can be either in a condensed form as a brownish thick liquid, or uncondensed form as a vapour. Coke oven emissions are a mixture of coal tar, coal tar pitch, and creosote and contain chemicals such as benzo(a)pyrene, benzanthracene, chrysene, and phenanthrene. Chronic (long-term) exposure to coke oven emissions in humans results in conjunctivitis, severe dermatitis, and lesions of the respiratory and digestive systems. Epidemiologic studies of coke oven workers have reported an increase in cancer of the lung, trachea, bronchus, kidney, prostate, and other sites. ETHYLENE OXIDE Sources of ethylene oxide emissions into the air include uncontrolled emissions or venting with other gases in industrial settings. Other sources of ethylene oxide air emissions include automobile exhaust and its release from commodity-fumigated materials. Individuals may be exposed to ethylene oxide through breathing contaminated air or from smoking tobacco or being in the proximity to someone who is smoking. Ethylene Oxide has been linked to reproductive damage, including spontaneous abortions; cytogenetic damage; neurological effects ranging from nausea and dizziness to peripheral paralysis; and tissue irritation. ISOCYANATES Isocyanates are compounds that contain a group of atoms consisting of Nitrogen (N), Carbon (C), and Oxygen (O), which make isocyanates very useful in the manufacturing industry. Isocyanates are commonly used in the production of plastics, foams, and coatings. Health effects associated with exposure to isocyanates are: decreased lung function, cold and flu-like symptoms, fever and shortness of breath. Exposure to isocyanates can be through inhalation of vapour, mist or dust, or by direct contact. LEAD For thousands of years lead has been used industrially because of its poor conductive property. Lead has been commonly used for electric storage batteries, pigments, paints, and rubber compounds. Health effects associated with lead exposure can result in damage to the kidneys, gastrointestinal system, nervous system and reproductive system. Symptoms range from vomiting, and abdominal cramps to pains in joints and muscles. MERCURY At room temperature mercury is in the form of a silver colored liquid. Mercury can exist in three forms: elemental, the pure form; organic, where mercury is bonded to a carbon molecule; or inorganic, where mercury is bonded to a molecule other than carbon. Page 2

61 Mercury can be absorbed into the body by inhalation, ingestion or absorption through the skin. As a health hazard mercury can affect the respiratory system resulting in coughing and chest pains. Mercury poisoning can also cause kidney damage, skin irritation and may even harm the nervous system. SILICA Silica can be found naturally in two forms, crystalline or amorphous material. Crystalline silica is regulated due to its significant toxicity over the amorphous silica. The three most common forms of crystalline silica in the workplace are: quartz, cristobalite and tridymite. The physical properties of silica make it a valuable substance for use in a variety of different industries and processes such as an abrasive and scouring compound, fillers for paint and mastic and optical equipment. Health effects resulting from exposure to crystalline silica range from eye and skin irritation, coughing and sneezing to silicosis a progressive lung disease. VINYL CHLORIDE Vinyl chloride is required in the manufacture of polyvinyl chloride (PVC) and at room temperature is present as a colorless, flammable gas. Vinyl chloride is also known as chloroethene, chloroethylene, and ethylene monochloride, and can result from the breakdown of other substances such as trichloroethane, trichloroethylene, and tetrachloroethylene. Common exposure is a result of inhaling vinyl chloride from industrial leaks, hazardous waste sites and landfills. Symptoms of breathing vinyl chloride are sleepiness, dizziness or labored breathing. Chronic exposure can cause liver and nerve damage or cancer. Page 3

62 APPENDIX D LABORATORY ANALYSIS REPORT

63 APPENDIX E SITE PHOTOGRAPHS

64 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph No. 1: View of the Residential Property located at Street East, Peterborough, Ontario (Subject Location). Photograph 2: View of the asbestos-containing white paper wrap on the ductwork at the Residential Property.

65 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 3: View of the asbestos-containing 12 x12 white with stone pattern VFTs observed at the Residential Property. Photograph 4: View of the asbestos-containing texture coat on the ceiling of the north storage room adjacent to the kitchen at the Residential Property.

66 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 5: View of the asbestos-containing heat shield in the entertainment room at the Residential Property. Photograph 6: View of the asbestos-containing texture coat on the ceiling of the entertainment room at the Residential Property.

67 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 7: View of the asbestos-containing window putty exterior on the east window frame at the Residential Property. Photograph 8: View of the asbestos-containing black caulking on the north section of exterior window frame at the Commercial Property.

68 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 9: View of the asbestos-containing grey caulking on the exterior south door frame at the Commercial Property. Photograph 10: View of the suspect asbestos-containing electrical wire sheathing observed throughout the Residential and Commercial properties.

69 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 11: View of the lead-containing off-white paint observed on the ceiling of the north vestibule area of the Residential Property. Photograph 12: View of the lead-containing brown paint observed on the west wall and light green paint observed on the baseboard in the south vestibule area of the Residential Property.

70 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 13: View of the lead-containing beige paint observed on the north wall of the kitchen adjacent to the washroom at the Residential Property. Photograph 14: View of the lead-containing red paint observed on the north porch of the Residential Property.

71 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 15: View of the lead-containing green paint and beige paint observed on the exterior window frames of the Residential Property. Photograph 16: View of the lead-containing neon green paint observed on the shelves and grey paint observed on the door observed in the main office area of the Commercial Property.

72 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 17: View of the lead-containing yellow paint observed on the metal panel on the north exterior wall of the Commercial Property. Photograph 18: View of the mercury-containing thermostat observed on the south wall of the kitchen of the Residential Property.

73 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 19: View of the mercury-containing thermostat observed on the south wall of the main office area of the Commercial Property. Photograph 20: View of the Philips (Cat. No. R-2E75-S-TPC) light ballast observed at the Commercial Property marked with a label indicating Non-PCB.

74 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 21: View of the Advance (Cat. No. R-2E75-S-TPC) light ballast observed at the Commercial Property marked with a label indicating Non-PCB. Photograph 22: View of the Philips (Cat. No. SM-2E75-S-TPC) light ballast observed at the Commercial Property marked with a label indicating Non-PCB.

75 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 23: View of the Alliance (Cat. No. 17A297EW) light ballast observed at the Commercial Property marked with a label indicating Non-PCB. Photograph 24: View of the Canadian GE Electronics (Cat. No. 17A297TW) light ballast observed at the Commercial Property and based on its label is suspected to contain PCBs.

76 Site Photograph Residential and Commercial Property, 212 and 210 Street East, Peterborough, Ontario Project No.: Photograph 25: View of the Sylvania (Cat. No. MB2.96/120 IS) light ballast observed at the Commercial Property marked with a label indicating Non-PCB. Photograph 26: View of the Philips (Cat. No. R-2C34-TPC) light ballast observed at the Residential Property marked with a label indicating Non-PCB.