Contents. MAGO Anchor Channel. Copyrights. Anchor Channel. Hot-Rolled Anchor Channel - ACH. Stainless steel Cold rolled Anchor channel ACF-S

Transcription

1 Contents MAGO Anchor Channel Anchor Channel Hot-Rolled Anchor Channel - ACH Stainless steel Cold rolled Anchor channel ACF-S Standard lengths and anchor spacing T-bolt Tightening Torque Framing Channels Channel Profiles Channel Nuts and Set Screws Allowable loads Dynamic oading Spacings and edge distances Reduced edge distances ar for maximum allowable pull out loads FZ MAGO Reduced edge distances ae for maximum allowable loads FZ and FQ Failure Method for Mago Channel and T-Bolt 1 In lean CEN / TS Copyrights Any reproduction in whole or in part, in any form by any means, electronic or mechanical, or by information storage and retrieval systems without prior written consent from MAGO is strictly prohibited and will lead to legal prosecution. The information contained in this catalog is considered accurate. No warranty; however, is expressed or implied regarding its accuracy or the results to be obtained from the use thereof. The user shall determine the suitability of a product prior to its use for the intended application and assume all risk and liability in connection therewith. While all due care and attention has been taken in this catalog, due to product developments it may occur that some of the data included is no longer valid. Should you wish to be updated with our latest product information, please contact us.

2 MAGO Anchor Channel Anchor channel is a flexible and effective solution to fix various items to precast concrete, The Anchor channels are made of C-shaped channels with anchor bolts swaged on to transfer the load into the concrete. load ranges and different channel lengths cover most of the typical applications. Polyethylene foam filler is filled in the channel to prevent the ingress of concrete during pouring. Cold rolled Anchor channel - ACF ØD Ød ACF Profile Dimensions t Profile ACF 2/1 W 2 h 1 Dimensions () g t 2. 4 D d oad Class ().00 g w ACF 40/2 & 49/0 & 4/ ØD h ACF / ACF 40/2 ACF 49/ t Ød ACF 4/ ACF 2/ g w h ACF 2/1 & /1 The cold Rolled Anchor Channel is made from Cold-rolled Profile (St), zinc-plated or hot-dip Galvanized. it s an economical and simple solution for most applications. Features: 1. Mechanical swaged anchors ensure the maximum performance of the channel. 2. One Piece Polythene foam makes it easier and faster to remove the foam for installation of fixings,as well as keeping a clean work enviroment.. Hot-dip Galvanization is availlable for better anti-corrosion performance. MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0 1

3 MAGO Hot-Rolled Anchor Channel - ACH ACF Profile Dimensions Profile W h Dimensions () g t D d oad Class () ACH 40/ ACH 0/ ACH 2/ ACH / ACH 2/ The Hot Rolled Anchor Channel is made from Hot-rolled Profile, which provides better performances for dynamic loads and shock loads. Features: 1. Hot-Rolled Profile provides better performance for dynamic loads and shock loads. 2. The Mechanical swaged anchors ensures the maximum Performance of the Hot-rolled profile.. One Piece Polythene foam makes it easier and faster to remove the foam for installation of fixings, as well as keeping a clean work environment. ØD ØD Ød Ød t t h h g g w w ACH 40/ & 2/4 ACH 0/0 2 MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0

4 MAGO Stainless steel Cold rolled Anchor channel ACF-S The Stainless Steel cold rolled Anchor Channel is made from Stainless steel Profile (AISI 04/1) with mechanical swaged anchors. All stainless steel guarantees no rust leakage for good. Features: 1. Both the profile and the mechanical swaged anchors are stainless steel, 0% prevent the facades from any leakage of rust. 2. The Stainless steel Mechanical swaged anchors ensure the maximum Performance of the Stainless steel profile.. One Piece Polythene foam makes it easier and faster to remove the foam for installation of fixings, as well as keeping a clean work environment. MAGO Standard lengths and anchor spacing Channel ength () Spacer between centres > Note: ong length upto meters available with all our types of anchor channels (ACF-C Carbon steel Cold rolled profile, ACF-S Stainless steel and ACH Hot rolled profile. MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0

5 MAGO T-bolt 2 types of T-Bolts cover the full range of our anchor channels: Flat Head T-Bolts (T2 & T) to cover the profile sizes 2/1 and /1 and Hook Head T-Bolts (T4 & T) for all other profile sizes. Material: Normal steel bolt grade 4./., Zinc-plated / Hot-dip Galvanized Stainless steel grade 04-1-A4 Anchor Channel T Bolt Type d () Head ength I () Head Width w () Head Thickness t () ength () Bolt Tension oad () Bolt Shear oad () ACF 2 / 1 ACF 1 / ACF 2 / 40 ACH 2 / 40 ACF 4 / ACH 2 / 4 ACF 49 / 0 ACH 0 / 0 ACH / 42 ACF 2 / 4 ACH 2 / 4 T 2 T T 4 T M M M M M M M M M M M M M M M Note: When The Bolt Allow. oad is bigger than that of the Anchor channel. the Allow. oad of the Anchor channel must not be exceeded. Type T4 Type T2 & T & T HDG Z.Plated 04-1-A4 4 MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0

6 Tightening Torque Connecting Plate Connecting Plate 1-A4-0 Washer 4. 1-A4-0 1-A4-0 F A4-0 1-A4-0 F4-0 ACF 2 / 1 ACF / 1 ACH 40 / ACF 40 / 2 ACH 0 / 0 ACF 0 / 0 ACH 2 / 4 ACF 4 / ACH / 42 ACH 2 / 4 ACF 2 / 4 MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0

7 MAGO Framing Channels Mago framing channel system provides an efficient and economical solution for structur support and attachment with its full adjustability and detachability. It can be used for supporting almost all kinds of building services such as piping, cabling and ducting etc. With our complete range of channels, fasteners and brackets, even no welding or drilling on site is needed. Channel Profiles 2 basic channel profiles are available for different load capacities. NC x NC x Single Profile Description Material /Finish Width Height Weight kg/m Cross section cm 2 Max. Allowable Point oading oad at span < Bending Capacity () at Span 0.m 1.0m 1.m NC x NC x NC x Double NC x 21 Double Double Profile Description Material /Finish Width Height Weight kg/m Cross section cm 2 Max. Allowable Point oading oad at span < Bending Capacity () at Span 0.m 1.0m 1.m NC x NC x MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0

8 MAGO Perforatd Channel Profiles NC x Slotted NC x 21 Slotted Single Profile Description Material /Finish Width Height Weight kg/m Cross section cm 2 Max. Allowable Point oading oad at span < Bending Capacity () at Span 0.m 1.0m 1.m NC x NC x MAGO Channel Nuts and Set Screws types of channel nuts are used to meet different application needs: long, short and plain spring types. All types can be supplied in M, M and M thread. GNR GNR SR GNR S GNR fo channel NC x and x21 Ref. No. GNR fo channel NC x Ref. No. GNR fo channel NC x 21 Ref. No. Material /Finish Thread size Nut thickness t Nut width b Max. central pull load Max. longitudinal oad GNR -M GNR -M GNR -M M GNR -M GNR -M GNR -M M GNR -M GNR -M GNR -M M 20.1 GNR -M GNR -M GNR -M M 20. With above channel nuts most fixing jobs can done with standard fasteners such as hex bolts, washers, hex nuts, threaded rods etc... MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0

9 MAGO Allowable loads The allowable loads are determined by the following tables (Pull and shear loads) by choosing the right anchor channels and bolts. Also the load can be individually calculated by using the concrete capacity design (CCD) procedure taking into account the concrete strength, the anchor depth and the edge and center spacings. Allowable direct pull out and angled pull out oads FZ angle ong lengths Short length Point loads oad pairs Point loads oad pairs Channel , > 20 = / / / 40/ /0 0/0 2/4 4/ 20 / / Note: Please contact MAGO engineering department for any technical support for special individual application. MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0

10 Allowable transverse shear and angled shear oads FQ FQ angle 1 ong lengths Short length Point loads oad pairs Point loads oad pairs Channel , /1.. / / 40/2 49/0 0/0 2/4 4/ / / Note: 1. The above allowable loads are for concrete 2Mpa. For lower concrete strength 1Mpa or 20Mpa, the load shall be reduced by a factor of 0. or 0. respectively. 2. The above allowable loads might be bigger than the allowable loads of the bolts, to reach the allowable loads, other bolts must be used.. For concrete strength > Mpa, additional crack prevention reinforcement (min. bars grade BSt00S around each anchor channel) must be applied. MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0 9

11 MAGO Dynamic oading. The Hot-Rolled Anchor Channel ACH is suitable for dynamic loading. The adjacent table gives the allowable cyclic loads (Tenion) under N= 2x, Anchor Channel Size ACH 40/ ACH 0/0 ACH 2/4 Allowable Amplitude (Tensile oading) 2,0 2,4,0 Note: ACH 2/4 w/t I shaped anchor welded on. Spacings and edge distances The spacings and edge distances given in the table below are for reinforced concrete min. strength 2Mpa, standard reinfocement is required for the element. ar aa ar ae ar1 af a1 ar1 Center spacing and edge distances (cm) ae Channel ar aa ae af ar1 a1 2/ / /2 0/ / / /4 4/ /42 4/ Note: 1. For unreinforced concrete, the min. spacings should be increased by 0% for the values given in the table. 2. For a transverse or diagonal load, the edge distance of the unloaded edge ar may be reduced to min. cm provided additional reinforcement is applied.. The thickness of the concrete element depends on the length of the anchor and the necessary conrete cover "c" shown the in table below. C2 Anchor Channel Size 2/1 /1 40/2 40/ 49/0 0/0 2/4 4/ /42 2/4 C1 Concrete Cover c1 () >40 >40 >0 > >0 > >0 c2 can be according to DIN 4 MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0

12 MAGO Reduced edge distances ar for maximum allowable pull out loads FZ For thin walls or beams, the edge distance a r can be reduced to cm, provided additional reinforcement is applied as shown in the following figures. Anchor channel Straight reinforcement bar diameter U-shaped reinforcement bar Thin wall or beam ae Minimum allow. bend diameter as per DIN 4 As b,net (DIN4) 4 e e+ Requ. As [cm²]: cross-sectional area of reinforcement Requ. As= allow. 4xσs Note: σs = Allow. steel stress, Allow. [] = Allowable loadas. MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0

13 MAGO Reduced edge distances ae for maximum allowable loads FZ and FQ For anchor channels 2/1, /1 and 40/2, The end edge distance ae can be reduced for applications like in thin and long reinforced concrete columns, provided 2 additional reinforcement bars (see figures below) are installed just above and below the length of the anchor channel. The distance from the edge of the concrete column to the centre of the anchor must be at least 42. Straight reinforcement bar diameter 1 Slender column Anchor channel Additional reinforcement bar diameter F 2 2. ae a a a a a Allowable loads FZ, FQ and load spacing a oad spacing a Max Min Anchor channel oad angle Allowable loads F [] 2/1 FQ /1 FQ /2 FQ MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0

14 Notes Failure Method for Mago Channel and T-Bolt In lean CEN / TS Tension Shear Steel Concrete Steel Concrete Anchor break Eventually Pull-out T-Bolt failure Concrete side break Connection failure Concrete failure Anchor connection failure Concrete edge failure Bending of the channel lip Splitting Anchor shaft failure T-Bolt failure Concrete side break Bending of the channel lip Deformation failure MAGO Befestingungstechnik GmbH. Innotech Center / Top 1.1e. Salurnerstr.. A-0 Kufstein. Austria Tel.: Fax.: info@mago.at Bank Austria: IBAN = AT / BIC = BKAUATWW FN 2 z. Sitz Kufstein. Firmenbuchgeicht: andesgericht Innsbruck. UID: ATU 0 1