Installation Manual Montageanleitung Instructions de montage Istruzioni per il montaggio

Transcription

1 Installation Manual Montageanleitung Instructions de montage Istruzioni per il montaggio

2 Product Data Installation Product Specifications Geberit Model No..08.xx. Features Water consumption: Dual flush system allows for 0.8 GPF ( l) or.6 GPF (6 l) For wall-hung washdown toilets see -->www. geberit.us for compatibility listing 8 mm ESG tempered safety glass Concealed water supply cupc listed X Material Determination Recommended material for wall surface construction ( x /" or x /8"): Gypsum / green board Cement board Tile backer board Ceramic tile surface Warranty Limited lifetime warranty on tank and frame. 0 year warranty on fill valve and flush valve. Dimensions ll dimensions are inches unless otherwise specified. X H Seat Height ~Rim Height H X Installation Requirements To install Geberit Monolith, a x 6" or x 4" wood frame or metal frame construction is required. Studs must be placed where Geberit Monolith will be positioned. Reference only! lways consult ceramic manufacturers data sheets for latest fixture dimensions.

3 Drainage elbow installation Centerline of new Geberit Monolith installation Water supply installation Stub out water supply line. ngle stop valve to be installed later. Top view 8½" FF Center of HDPE 90 degree elbow (supplied) X Front view 5" " For ½" copper supply Top view x 4 wall " Sch 40 PVC Up through floor. Connect with Flexible coupling (supplied) Hole through floor, minimum dimensions ½" square Water supply lternate position (same dimensions) 8½" " FF ¾" to center of " PVC and 90 degree elbow Top view x 6 wall Hole through floor, minimum dimensions ½" square ½" to center of " PVC and 90 degree elbow Install protection plug (yellow)

4 Frame installation 8½" Option : Tile wall CUTION High torque forces Structure may be damaged Do not overtighten hex nuts. ø /8 '' 8 / 85 / 5 4" 4" " 5" 7½" FF ½" 59 /4 5" () x 4 to ceiling OR () x 6 to ceiling with centers as shown Strap drainage elbow to studs to prevent from falling back into wall. F.F. 0 /4 5 /4 5 /4 Finish wall surface construction. mm 4 ttach supplied angle valve. /4 Outlet of valve must point to 6 o clock position! Option : Tile wall see page 4 Option : Painted wall see page 6 4

5 Be sure this mark is lined up at elevation "X". It should also be equal to center of drainage elbow. T 0 X 5 Fine leveling adjustment. Raise or lower sides as needed. + /8 5 mm - /8 4 6 mm 5

6 7 ø /8 '' Option : Painted wall CUTION High torque forces Structure may be damaged Do not overtighten hex nuts. 8 / 8 / ø /64 '' 8 5 /4 mm ø /8 '' F.F. /4 5 /4 5 /4 mm 4 To complete the installaton continue on page 8. /4 6

7 Be sure this mark is lined up at elevation "X". It should also be equal to center of drainage elbow. T 0 X 5 Fine leveling adjustment. Raise or lower sides as needed. mm 4 4 /4 6 mm 7

8 7 ø /64 '' Common installation steps (tile and painted wall) CUTION High torque forces Structure may be damaged Do not overtighten hex nuts. mm 8 mm mm 8

9 5 H H H H 4 6 CUTION Leaking connection Do not forget sealing washer. 9

10 7 5 mm 00:00: For water supply on right (B), filling valve can remain in position as supplied. For water supply on left (), filling valve must be repositioned (see next steps). () (B) 0

11 Use ceramic or data sheet to find dimension T. T 4 Hand tight + /4 turn. Larger diameter end Smaller diameter end T 7

12 5 Check that inserts are fully unlocked before inserting into Geberit Monolith. 6 7 Glass must have even offset all around. PH ~ /6 ~ /6 80

13 8 9 B B B 0 T T X T T X + /8 4

14 4 4

15 5 8 9 mm 6 5 mm 9 7 Click 5

16 Geberit 00 Clearwater Drive, Des Plaines, IL Phone: 847/ Fax: 847/ For Technical ssistance 800/TEC-TRUE (800/8-878) Geberit International G Schachenstrasse 77 CH-8645 Jona dokumentation@geberit.com (00)