K5 AQUAPLUG A FAST SETTING PLUGGING COMPOUD FOR STOPPAGE OF RUNNING WATER

Transcription

1 ISO COMPANY K5 AQUAPLUG A FAST SETTING PLUGGING COMPOUD FOR STOPPAGE OF RUNNING WATER DESCRIPTION K5 AQUAPLUG is a fast setting hydraulic compound which stops running water instantly. K5 AQUAPLUG sets with in 1 to 3 minutes depending on temperature and the surface to which it is applied. Lower temperature will retard the setting time and higher temperature accelerates the setting time. USES It can be used for stop running water and seepage through concrete and masonry walls, dams, and wall and floor junctions. It can be used as a grout around pipes. ADVANTAGES Stops running water instantly. Sets under water. Non-shrink, non-metallic. Chloride free. High structural strength Easy to use. APPLICATION INSTRUCTIONS SURFACE PREPARATION: Chisel out masonry around the hole or crack to a depth and width not less than 25 mm. Ensure that the hole is wider with in the wall than at the surface. (Inverted 'V' Groove). If the water pressure is high at the area to be patched, make weep holes at the base of the wall to relieve the pressure. MIXING: K5 AQUAPLUG should be mixed with a trowel in small quantities 1:4 by volume or 1:5 by weight (water to K5 AQUARPLUG). APPLICATION: Hold the mixed K5 AQUAPLUG in the gloved hand until heat generation is felt and force the material in to the crack or void and hold tightly with palm of the hand for 3 minutes until K5 AQUAPLUG sets.

2 PACKING & COVERAGE 5 kg bag. SHELF LIFE 12 months storage life when stored in original unopened container at between 5 ºC to 45 ºC in a dry and shaded place. HEALTH & SAFETY K5 AQUAPLUG is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves water should be worn. In the case of contact with eyes, rinse immediately with plenty of and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting. NOTE All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

3 ISO COMPANY K5 WATERGUARD INS Electrometric, acrylic polymer based Insulating coating DESCRIPTION K5 WATERGUARD INS. is a two component, polymer based waterproofing coating with insulating property to cool down inner temperature and ensures the flexibility to cover the thermal stresses. It has an excellent frost resistance. Can be used on vertical and horizontal surfaces. This system also has certain waterproofing properties and is able to bridge hairline cracks caused by thermal movements. USES Application Areas Include: Concrete or metal roofs Asbestos sheet and other metal surfaces External and internal walls Cold storage facilities Terrace and balconies. ADVANTAGES Excellent flexibility at both high and low temperatures. Excellent adhesion to most building substrates. Non conductive property saves air conditioning energy cost. Flexible high elongation characteristics. Excellent resistance to water provides good insulation property. Breathable allows water vapour to escape. Easy to apply APPLICATION INSTRUCTIONS SURFACE PREPARATION: Substrate must be sound, clean and free from loose particles or laitance or contamination and preferably be wire brushed. Where cracks are present, cracks must be treated first depending on the type of crack. MIXING : Pour liquid in to suitable clean containers. Then slowly add powder while stirring with a mechanical mixer, carefully mix K5 WATERGUARD INS for a few minutes making sure that no powder remains stuck to the sides or the bottom of the container. Keep stirring until a perfectly homogenous mix is obtained. Use a low speed mixer for this operation to avoid much air being dragged in to the mix.

4 APPLICATION : The prepared surface must be thoroughly wetted with water for absorption and excess water to be removed. Apply mixed K5 WATERGUARD INS by brush at a maximum thickness of 1 to 2 mm per layer. The second coat must be applied when the previous one is dry ( after 8 10 hours.) The mixed material to be used with in 20 minutes. PACKING & COVERAGE 10 kg powder + 5 ltr. Liquid will cover 5 m 2 to 7 m 2 SHELF LIFE 12 months storage life when stored in original unopened container at between 5 ºC to 45 ºC in a dry and shaded place. HEALTH & SAFETY K5 WATERGUARD INS is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting. NOTE All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

5 ISO COMPANY K5 AQUAGUARD WM (F) CEMENTITIOUS FIBER REINFORCED WATERPROOFING RENDER DESCRIPTION K5 AQUAGUARD WM (F) is a single component fiber reinforcement cementitious water proofing render. Normally to be used in conjunction with K5 AQUAGUARD A as a primer. USES It can be used for terrace slab, Basement, Water Tank, Reservoirs etc. For water proofing and protection of all structures, foundations, retaining walls, swimming pools, bridges Lift shafts, Tunnels, Dock gates, Dams etc. ADVANTAGES Pre packed easy to use by trowel. Can resist hydrostatic pressures. Ensures perfect water proofing. Economical and cost effective waterproofing system. Fiber reinforced mortar so increase the compressive and tensile strength. Compensates the shrinkage and ensures perfect bond with the substrates. APPLICATION INSTRUCTIONS SURFACE PREPARATION: Substrate must be sound, clean and free from loose particles or laittances or contamination and preferably be wire brushed. MIXING: K5 AQUAGUARD WM (F) must be mixed with a mechanical mixer using an electric drill paddle attachment. Place the required amount of water in the container (3.2 to 3.5 ltrs. of water / 25 kg bag) and whilst mixing add the powder slowly and mix till homogeneous trowel able consistency is obtainer. APPLICATION: Apply K5 AQUAGUARD A (see separate data sheet) by brush as a primer coat. When K5 AQUAGUARD A is wet apply the K5 AQUAGUARD WM (F) at thickness of 10mm to 15 mm and finish the surface by trowel. After 2 hour one coat apply K5 AQUAGUARD A as a sealing coat. PACKING & COVERAGE 25 kg bags yield approx. 11 ltrs. Covers 1.4 m 2 for 10 mm thickness.

6 SHELF LIFE 6 months storage life when stored in original unopened container at between 5 ºC to 45 ºC in a dry and shaded place. HEALTH & SAFETY K5 AQUAGUARD WM (F) is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting. NOTE All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

7 ISO COMPANY K5 WATERGAURD CL SINGLE PACK ELASTOMERIC READY TO USE MULTI COLOURED WATERPROOFING COATING DESCRIPTION K5 WATERGUARD CL is a single component ready to use waterproofing coating contains special waterproofing fillers to ensure waterproofing. It also provides extremely tough decorative waterproof coating, which allows breathing the surface. USES Can be used in all types of slab, Vertical/Horizontal Surfaces, etc. ADVANTAGES Single pack, ready to use. Available in various colours. Can be applied on vertical & horizontal surfaces. Gives insulation properties. Abrasion resistant. Allows the surface to breathe. Flexible. Cost effective. Easy to apply. Excellent water tightness. PROPERTIES Surface finish: Matt. Application Temperature: 30C to 400C. Dry Time: 30 minutes two to three coats are recommended for perfect waterproof. Colour: Biscuit, Cream, Pista, Grey, White (Special shades on request). Insulation: Two coats of K5 WATERGUARD CL will ensure 2 to 30C less temperature (and light shade 3 to 40C less temperature) APPLICATION INSTRUCTIONS SURFACE PREPARATION: Substrate must be sound, clean and free from loose particles or laittances or contamination and preferably be wire brushed. Where cracks are present, cracks must be treated first depending on the type of crack.

8 APPLICATION: The prepared surface must be thoroughly wetted with water for absorption and excess water to be removed. K5 WATERGUARD CL must be applied by brush in 2/3 uniform coats. PACKING & COVERAGE 1, 5 and 20 kg. Plastic bucket. 1 kg. K5 WATERGUARD CL will cover 4 to 5 m 2 SHELF LIFE 12 months storage life when stored in original unopened container at between 5 ºC to 45 ºC in a dry and shaded place. HEALTH & SAFETY K5 WATERGUARD CL is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting. NOTE All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

9 ISO COMPANY K5 WATERGUARD TR A TROWEL APPLIED SINGLE PACK FIBRE REINFORCED WATERPROOF CEMENTITIOUS RENDER DESCRIPTION K 5 WATERGUARD TR is a prepacked cementitious water proofing render which is to be troweled on as a 5mm thick render normally used In conjunction with K5 AQUAGUARD A as a primer. K 5 WATERGUARD TR is cementitious fibre reinforced waterproofing mortar for watertank, basement etc. Where hydrostatic pressure exists. USES For waterproofing and protection of all structures; like Basements, Water tanks, Foundations, Retaining walls, Swimming Pools, Bridge Decks, Lift shafts, Tunnels, Dock Gates, Dams, Reservoirs. Where very high hydrostatic pressure exists, K 5 WATERGUARD TR must be applied in 2 coats of 5mm thickness. ADVANTAGES Economical and easy to use Prepacked factory controlled ready to use mortar. Only precise quantity of water to be added Can resist hydrostatic pressures Ensures perfect water tightness Fiber reinforced mortar ensures long durability and water tightness. APPLICATION INSTRUCTIONS SURFACE PREPARATION (1) All leaks and water jets must be stopped using WATERPLUG Compound. (Refer relevant Data Sheet). (2) All surfaces must be sound, clean and free from oil and contamination. All loose particles must be removed by wire brushing. (3) All surfaces must be wetted thoroughly with water to allow surface absorption and excess water to be removed before application of K 5 WATERGUARD TR. MIXING K 5 WATERGUARD TR must be mixed in a mechanical mixer using an electric drill paddle attachment. Place the required amount of water in the

10 Container (5 to 5.5 Liters of water / 25 kg bag) and during mixing add the powder slowly and mix till homogeneous trowellable consistency is obtained. (Mixing of k FIBRE 125 gm / 25 Kg bag of K 5 WATERGUARD TR is recommended to ensure perfect bond and water proofing). APPLICATION K5AQUAGUARD A as a primer coat and when K5AQUAGUARD A is wet apply 5mm thick K 5 WATERGUARD TR mortar. Normally K 5 WATERGUARD TR is used for same thickness treatment. (See WATERGUARD WM (F) application guide.) CURING The K 5 WATERGUARD TR applied surface must be kept under water at least for 7 days and only after that the surface should be brought to use. CLEANING All tools must be cleaned with water immediately after use. PACKING & COVERAGE 25 Kg HDPE bags. 25 Kg bag yields approximately 13 Litres which covers 2.6 sq. m. for 5 mm thickness. SHELF LIFE 6 months storage life when stored in original unopened container at between 5 ºC to 45 ºC in a dry and shaded place. HEALTH & SAFETY K5 WATERGUARD TR is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting. NOTE All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

11 ISO COMPANY K5 WATERGUARD AS AN EASILY BRUSH APPLIED SINGLE PACK ACRYLIC BASED PENETRATING WATER PROOF COATING BENEFITS Economical and easy to use Excellent adhesion Allows surface to breath Excellent waterproofing characteristics. Seals the porous surface and will not allow water to penetrate. Colourless coating. Flexible. Resists efflorescence. Penetrates into the concrete and seals the surface. Long life. Resists ultra violet radiation. Prevent staining and ingress of dirt, grime, oil or grease, rust spotting, pitting dusting and discolouration. PRODUCT A single pack acrylic base waterproof coating which can be easily applied by brush or roller which ensures excellent waterproofing properties. USES For all structures which are required to be waterproofed and to be protected against the ingress of moisture. Basements, Lift Shafts, Swimming Pools, Sewage Tanks, Sunk slab, Balconies, Terrace State, marble, paving, brick, quarry tiles, terrazzo and exposed aggregate panels and paving etc.

12 DESCRIPTION K5WATERGUARD AS is a colourless acrylic based coating which can be applied by brush or roller. Two coats of K5 WATERGUARD AS will ensure micron film thickness. K5 WATERGUARD AS should be applied without any dilution. The product starts curing immediately on exposure to air due to the built-in catalyst and the curing will complete within 24 hrs of application, K5 WATERGUARD AS gives a totally dry elastic film within 24 hrs. PROPERTIES K5 WATERGUARD AS when used as recommended two coats to form an impermeable coating by blocking the capillaries and pores. Appearance - Clear white Liquid. 25 O C. Cps S.g SURFACE PREPARATION All leaks and water jets must be stopped using AQUA PLUG plugging compound. Substrate must be sound, clean and free from loose particle or laitance or contamination and present cracks must be treated first depending on the type of crack. Before application of K5 WATERGUARD AS surface should be DRY. MIXING K5 WATERGUARD AS is a ready to use product. No solvents or other diluents should be use. Before application of K5 WATERGUARD AS shake well the container. APPLICATION On the prepared surface two to three uniform coats should be applied by brush or roller. Left over materials should be properly packed in the tin for future use.

13 CLEANING All tools must be cleaned with SEAL CORE TOOL CLEANER immediately after use. PACKING & COVERAGE 1, 5, 10, 20 Liter. Carbouy, 1 liter of K5 WATERGUARD AS will cover 5-6 m 2 /per coat, (However coverage is depends on the porosity of surface). SHELF LIFE K5 WATERGUARD AS has a shelf life of 12 months when stored unopened in original sealed container under shade in dry conditions. HEALTH & SAFETY Gloves must be worn while handling epoxy resin based product, to prevent skin irritation. QUALITY ASSURANCE Krishna colours manufactures entire range of construction chemicals under compliance of ISO TECHNICAL SERVICES While new advances and changes will take place one thing will never change is quality and meeting special needs of customer. We are eager to work with you in development of new product and solve your problem.

14 ISO COMPANY K5 AQUAGUARD A TWO COMPONENT POLYMER MODIFIED WATER PROOFING COATING DESCRIPTION K5 AQUAGUARD A is a two component, flexible polymer modified brush applied cementitious coating for the protection of waterproofing of concrete surfaces, balconies, terraces, bathrooms and swimming pools. USES Waterproofing bathrooms, showers, balconies, terraces, swimming pools etc. Waterproofing for retaining walls or pre cast concrete elements embedded in the ground. All structures that are required to be waterproofed and protected against the ingress of moisture like Basements, Water tanks, Swimming Pools, Retaining Walls, Bridge Walls, Tunnels, Lift Shafts, Sewage Tanks, Reservoirs, Dams, Dock gates etc. Protection of concrete surfaces which may come into contact with sea water, de-icing salts, such as sodium or calcium chloride and sulphates. ADVANTAGES Pre packed easy to use water proofing coating. Excellent adhesion to most of the construction materials. Economical and cost effective waterproofing system. Excellent flexibility allows surfaces to breath. APPLICATION INSTRUCTIONS SURFACE PREPARATION: Substrate must be sound, clean and free from loose particles or laitance or contamination and preferably be wire brushed. Where cracks are present, cracks must be treated first depending on the type of crack. MIXING: Pour liquid in to suitable clean containers. Then slowly add powder while stirring with a mechanical mixer, carefully mix K5 AQUAGUARD A for a few minutes making sure that no powder remains stuck to the sides or the bottom of the container. Keep stirring until a perfectly homogenous mix is obtained. Use a low speed mixer for this operation to avoid much air being dragged in to the mix.

15 APPLICATION: The prepared surface must be thoroughly wetted with water for absorption and excess water to be removed. Apply mixed K5 AQUAGURAD A by brush at a maximum thickness of 1 to 2 mm per layer. The second coat must be applied when the previous one is dry (after 8 10 hours.) The mixed material to be used with in 20 minutes. PACKING & COVERAGE 18 kg powder + 10 ltr. Liquid will cover 16.5m 2 to 25 m 2 9 kg powder + 5 liquid will cover8.25 m 2 to 12.5 m 2 SHELF LIFE 9 months storage life when stored in original unopened container at between 5 ºC to 45 ºC in a dry and shaded place. HEALTH & SAFETY K5 AQUAGUARD A is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting. NOTE All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

16 ISO COMPANY K5 AQUAGUARD AN EASILY BRUSH APPLIED SINGLE PACK CEMENTITIOUS WATER PROOFING COATING DESCRIPTION K 5 AQUAGUARD is a prepacked single component powder based waterproofing system ensures the total and permanent solution to water leakage, ingress, or seepage in concrete structures or any cementitious substrate. The formation and development of insoluble crystals into water bearing capillaries and interstices effectively blocks the further passage of water and ensures permanent water tightness for the life of the structure. USES All structures which are required to be waterproofed and protected against the ingress of moisture. Basements, Lift Shafts, Water tanks, Swimming Pools, Sewage Tanks, Retaining Walls, Reservoirs, Bridge Pilers, Dams, Tunnels, Dock gates etc. Water tanks / towers Reservoirs Tunnels Swimming pools and water treatment works Dams and canals Concrete pipes Bridge decks Retaining walls and foundations ADVANTAGES Economical and easy to use Excellent adhesion Non toxic Allows surface to breath Excellent waterproofing characteristics. Provides total and permanent waterproofing properties. Non-toxic or tainting.

17 PROPERTIES K 5 AQUAGUARD when used as recommended combines with water and cement to form an impermeable coating by blocking the capillaries and pores. i.e. waterproofing by crystallization. APPLICATION INSTRUCTIONS SURFACE PREPARATION : All leaks and water jets must be stopped using K5 AQUAPLUG plugging compound. Substrate must be sound, clean and free from loose particles or laitance or contamination and present cracks must be treated with K5CRACKSEAL (See separate data sheet). MIXING: K 5 AQUAGUARD should preferably be mixed mechanically by using an electric drill and paddle attachment. Pour 8 to 9 liters of water in the container first and add powder slowly while mixing continuously until an even homogeneous mix of brushing consistency is obtained. APPLICATION: The prepared surface must be thoroughly wetted with water for absorption and excess water should be removed. K 5 AQUAGUARD must be applied in 2/3 uniform coats at an application rate of kg/m 2 per coat on the water pressure side of the structure. Mixed K 5 AQUAGUARD will remain workable for 20 minutes. Mixing in small quantities is recommended. CLEANING: All tools must be cleaned with water immediately after use. PACKING & COVERAGE 1 kg, 5 kg, 25 kg bag. Cover m2 at a rate of Kg / m 2, depends on the porosity of the surface. Two or three coats are recommended.

18 SHELF LIFE: 12 months storage life when stored in original unopened container at between 5 ºC to 45 ºC in a dry and shaded place. HEALTH & SAFETY: K5 AQUAGUARD is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting. NOTE: All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

19 ISO COMPANY K 5 WATERGAURD FLX TWO COMPONENTS HIGH PERFORMANCE POLYMER MODIFIED WATER PROOFING COATING FOR CONCRETE AND MASONRY SURFACES DESCRIPTION K5 WATERGUARD FLX is a two component acrylic polymer modified electrometric waterproofing coating which consists of powder and liquid. K5 WATERGUARD FLX has an excellent weather resistance. Can be used on vertical and horizontal surfaces. USES K5 WATERGUARD FLX provides a seamless, waterproof coating suitable for use in water tanks, reservoirs, swimming pools, roofs and ensure water tightness. Waterproofing for retaining walls or pre cast concrete elements embedded in the ground. All structures that are required to be waterproofed and protected against the ingress of moisture like Basements, Water tanks, Swimming Pools, Retaining Walls, Bridge Walls, Tunnels, Lift Shafts, Sewage Tanks, Reservoirs, Dams, Dock gates etc. ADVANTAGES Pre packed easy to use water proofing coating. Excellent adhesion to most of the construction materials. Economical and cost effective waterproofing system. Excellent flexibility allows surfaces to breath. Minimum surface preparation needed low labor costs. Applied directly to the damp concrete and masonry. Non toxic ideal for potable water tanks. Excellent for concrete roof, leaking brick and masonry walls. APPLICATION INSTRUCTIONS SURFACE PREPARATION: Substrate must be sound, clean and free from loose particles or laitance or contamination and preferably be wire brushed. Where cracks are present, cracks must be treated first depending on the type of crack.

20 MIXING : Pour liquid in to suitable clean containers. Then slowly add powder while stirring with a mechanical mixer, carefully mix K5 WATERGUARD FLX for a few minutes making sure that no powder remains stuck to the sides or the bottom of the container. Keep stirring until a perfectly homogenous mix is obtained. Use a low speed mixer for this operation to avoid much air being dragged in to the mix. APPLICATION : The prepared surface must be thoroughly wetted with water for absorption and excess water to be removed. Apply mixed K5 WATERGUARD FLX by brush at a maximum thickness of 1 to 2 mm per layer. The second coat must be applied when the previous one is dry (after 8 10 hours.) The mixed material to be used with in 20 minutes. PACKING & COVERAGE 10 kg powder + 5 liter. Liquid will cover 5 m 2 to 7 m 2 SHELF LIFE 9 months storage life when stored in original unopened container at between 5 ºC to 45 ºC in a dry and shaded place. HEALTH & SAFETY K5 WATERGUARD FLX is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting. NOTE All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

21 ISO COMPANY K5 WATERREPELLS HYDROPHOBIC IMPREGNANT SILANE BASE WATER REPELLENT DESCRIPTION K 5 WATERREPELLS is supplied as ready to use. On porous surfaces K 5 WATERREPELLS provides an invisible barrier to water penetration and remains effective for many years. K 5 WATERREPELLS prolongs the clean appearance of buildings, reduces chemical attack, minimizes efflorescence. Thermal and sound insulation are improved by keeping the wall dry and the risk of frost damage is reduced. It will be effective on treated clay brickwork, calcium silicate brickwork, cement-based materials and all types of natural stone masonry, including limestone.. The life of the treatment will depend on the extent of weathering to The treatment does not block the pores and therefore 'breathing' properties of the wall are unaffected. Trapped moisture can easily dry out. K 5 WATERREPELLS is extremely effective and most surfaces require a single coat applicationwhich the surface is exposed. Due to the excellent water-repellent properties of K 5 WATERREPELLS, dirt and other atmospheric impurities are washed off, by rain and its clean appearance is maintained for a longer period. The application of K 5 WATERREPELLS will considerably reduce efflorescence and because the structure remains dry, thermal and sound insulation are improved. The risk of spelling by frost action is minimized USES K 5 WATERREPELLS is suitable for external application to exterior walls of brick or concrete blocks, cement renderings, asbestos cement, concrete and all types of stone, including limestone. Also used as an injection damp coarse fluid To provide a durable barrier to water penetration of porous surfaces.

22 ADVANTAGES Pre packed easy to use water proofing coating. Easily applied water repellent treatment giving a self cleaning, hydrophobic surface to masonary, concrete and asbestos sheeting Effective water repellence Minimises efflorescence Economical Very easy to apply Colourless hence maintains natural colour of walls. Non toxic vapours. Environmentally friendly. Highly penetrative. Crack bridging. APPLICATION INSTRUCTIONS 1) COVERAGE RATES : One litre of K 5 WATERREPELLS will cover between 4 and 5 m 2 of surface depending upon porosity and surface texture. Normally one coat is sufficient, but very porous surfaces may require a further coat. 2) PREPARATION OF SURFACE : All surfaces to be treated must be sound, clean and dry. Any defects and cracks, other than hair line cracks, should be made good. Dirty surfaces should be thoroughly cleaned and organisms such as algae or lichens should be removed. In no circumstances should detergents be used as they may reduce the efficiency of the treatment. The surface should be allowed to dry before the application of K 5 WATERREPELLS. K 5 WATERREPELLS should not be applied over mastics surfaces Glass, etc. should be protected against splashing during application. 3) K 5 WATERREPELLS is supplied ready for use. Apply by brush or low pressure spray. The K 5 WATERREPELLSshould be applied liberally so that it runs freely down the surface to about six inches below the point of application. When applying by spray, the pressure should be kept as low as possible to avoid excessive misting, and the nozzle held close to the surface. K 5 WATERREPELLS dries within a few hours and becomes fully resistant to water 24 hours after application. Brushes, spray equipment, etc. may be cleaned with water.

23 PACKING & COVERAGE 1, 5, 10, 50, 100 Ltrs carbuoys.1 Ltr of K 5 WATERREPELLS will cover approx. 4 to 5 m 2 of surface depending upon porosity and surface texture. Normally one coat is sufficient. SHELF LIFE 24 months storage life when stored in original unopened container at between 5 ºC to 45 ºC in a dry and shaded place. HEALTH & SAFETY K5 WATERREPELLS is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting. NOTE All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.