Facestock physical properties. Value. Adhesive physical properties. Value. Type: Solvent Acrylic Caliper: inches 25.

Transcription

1 Page 1 of 1 DURABLE PORTFOLO 2 Mil Matte Chrome Polyester TC/S815/5# SCK ABC Product Data Sheet Spec#: 7666 Facestock 2 Mil Matte Chrome Polyester TC is a matte finished metallic film featuring excellent tear strength, heat resistance, dimensional stability, opacity and chemical resistance. Designed for printing with most solvent and some water-based flexographic inks. Suitable for thermal transfer printing applications with select thermal transfer ribbons. Specific testing required. Adhesive S815 adhesive is a high strength clear adhesive featuring high initial tack, adhesion and shear. Offers strong permanent bonding to a wide variety of substrates including high surface energy (HSE), low surface energy (LSE) and Facestock physical properties mperial Units Caliper: ASTM D1 Tensile: ASTM D882 Metric Units.2 inches 5.8 micron MD 22,7 PS 1,596 kg/sq cm CD 29,8 PS 2,95 kg/sq cm Adhesive physical properties mperial Units Metric Units Type: Solvent Acrylic Caliper:.1 inches 25.4 micron ASTM D1 Standard Coat 32 g/sq m Wt: Minimum Appl 45 F 7 C Temp: Service Min -3 F -34 C

2 Page 2 of 1 powder coat substrates. Excellent chemical and UV resistance. Liner 5#SCK is a bleached, supercalendered paper stock with very good diecutting and matrix stripping properties. Supplied with an Anti Block Coating ("ABC") on the backside of the liner to control adhesive and label transfer to the backside of the liner in finished, wound rolls. This liner should not be used in fanfolded label applications and is not recommended for back printability. Temp Range: Max 3 F 149 C Loop Tack Stainless Steel: PSTC oz/in 121. N/1mm Liner physical properties mperial Units Caliper: ASTM D1 Basis Wt: TAPP T41 * (24" x 36" 5 sheets) Tensile: ASTM D882 Tear: TAPP T414 Metric Units.32 inches micron 54.5 lbs/ream 88.8 g/sq m MD 48. lbs/inch N/25 mm CD 26. lbs/inch N/25 mm MD 1.8 ounces 49.9 grams CD 2.1 ounces 58.2 grams Liner Release: Total Construction Caliper (approximate): TML 9 o removal of Liner from Facestock. Rate of Removal Grams/2" Width 4 inches/min inches (6.2 mils; micron)

3 Page 3 of 1 DURABLE PORTFOLO Product Data Sheet Features and Benefits Opaque metallized facestock with very good hiding power and physical strength Glossy clear top coat that accepts most flexographic, letterpress, and rotary screen inks Very good thermal transfer printability with most wax/resin and resin ribbons Top coat and adhesive have excellent chemical resistance Applications and Uses This product is suitable for wide variety of durable labeling applications such as: Product identification labels Barcodes and rating plates Work in progress labels (WP) Property identifcation and asset tags Durable goods labeling Automotive exterior or underhood labels Meets GM6121M Type A & B; Daimler Chrysler MS-CG121 Type A, B, & D; Ford WSS-M99P34 Types A, A2, A3, & A4 UL Rating plates. This product is UL and UL-c recognized for indoor and outdoor use (see appendix). For specific information, see UL file # MH1725 for conditions of recognitions Printing and Converting The top coat is designed for printing by flexography with most solvent and some water based inks. Specially formulated inks are normally not needed, however, testing is recommend prior to final ink selection. Suitable for thermal transfer printing applications with select ribbons and printer models. This product can be die cut and stripped at high speeds on standard web-fed

4 Page 4 of 1 presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems. RoHS/Regulation 22/95/EU The substances listed in article 4 lid 1 of 22/95/EU (RoHS) are not intentionally used in this product. The concentration limits of these substances will not exceed the set maximum concentration limits as provided in the proposed amendment for 22/95/EU. Shelf Life Unless specified otherwise in this document, one year when stored at 72 F at 5% RH Note: The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under enduse conditions to ensure it meets the requirements of the specific application.

5 Page 5 of 1 DURABLE PORTFOLO Product Data Sheet Appendix Performance Data: The following technical data should be considered representative or typical only and should not be used for specification purposes. Surface 1. Stainless Steel 2. Aluminum 3. Polypropylene nitial (15 minute dwell) 72 Hours at Room Temperature 72 Hours at 12 F 96 Hours at 15 F (65 C) & 8% Relative Humidity oz/in N/1mm oz/in N/1mm oz/in N/1mm oz/in N/1mm HDPE LDPE ABS Plastic Environmental Performance: Chemical Resistance test results The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 18 peel. Adhesion to Stainless Steel Visual Edge

6 Page 6 of 1 Chemical oz/in N/1mm Appearance Penetration mm 1. 7% PA Tide Detergent 3. Engine Oil (1W3) Water Ammonia - ph Cleaner 7. Toluene 8. Brake Fluid 9. Reference Fuel C Kerosene K1 11. Heptane Compliance Recognition: UL, C-U Underwriters Laboratories, nc. Minimum Maximum Temperature Temperature Substrates o o o o (=ndoor F C F C Only =ndoor & Outdoor) 1. Stainless Steel Polyphenylene Oxide 3. Polyester Powder Paint

7 Page 7 of 1 4. Unsat Thermoset Polyester 5. ABS Plastic 6. Galvanized Steel 7. Epoxy Paint 8. Porcelain 9. Alkyd Enamel 1. Aluminum 11. Epoxy Powder Paint Polyester Paint Acrylic Powder Paint 14. Acrylic Paint 15. Phenolic 16. Polycarbonate 17. Nylon Polyethylene 19. Polypropylene 2. and others Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR6", Astro Med nc "R-5", Astro Med "RF", Astro Med "RY", Coding Prds "594", Dai Nippon "R-3", Dai Nippon "R-51", imak "SP- 41", imak "SP-33", imak "Primemark", ntermec "TMX 15", ntermec "TMX 32", TW "R1, TW "B324", Japan Pulp & Paper "Resin 1", Japan Pulp & Paper "Sigma P", Kurz "K3", Kurz "K5", Kurz "K51", Mid City Columbia "CGL- 8HE", Mid City Columbia "MCCHE", NCR "Promark 3", NCR "Perma Max", NCR "K3", Ricoh "B11C", Ricoh

8 Page 8 of 1 "B11CX", Ricoh "B11CR", Ricoh "12EC", Sato Corp. "Premier 1", Sony "TR47", Sony "TR475", Sony "TR57", Sony "TR67", Sony "TR675", Sony "Signature Series Resin", Union Chemicar "US3", Zebra "595", Zebra "51", Zebra "5175", Zebra "5463", Zebra "5555", Zebra "Z- 41", and others. Tested by Underwriters Laboratories, nc. to meet the requirements of the Canadian Standards Association for labeling materials Minimum Maximum Temperature Temperature Substrates o o o o (=ndoor F C F C Only =ndoor & Outdoor) 1. Metals Electrostatic Paints 3. Plastics Group 4. Plastics Group Plastics Group 6. Plastics Group V Plastics Group V 8. Plastics Group V Plastics Group V 1. Plastics Group

9 Page 9 of 1 V Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR6", Astro Med "RY", Dai Nippon "R-3", Dai Nippon "R-51", Japan Pulp & Paper "Resin 1", Kurz "K5", Mid City Columbia "CGL- 8HE", Mid City Columbia "MCCHE", NCR "Promark 3", Ricoh "B11C", Ricoh "B11CR", Sato Corp. "Premier 1", Sony "TR47", Sony "TR57", Sony "TR67", Sony "TR675", Sony "Signature Series Resin", Union Chemicar "US3", Zebra "51", and others. 49 is a registered trademark of the Clorox Company Tide is a registered trademark of the Procter & Gamble Company The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing.

10 Page 1 of 1 Warranty All statements, technical information and recommendations about AVERY DENNSON products are based upon tests believed to be reliable but do not constitute a guarantee or warranty. All AVERY DENNSON products are sold with the understanding that PURCHASER has independently determined suitability of such products for its purposes. AVERY DENNSON products are warranted to the original purchaser to be free from defects in material or workmanship for a period of one year from date of shipment. Purchaser's sole and exclusive remedy for breach of this warranty shall be the replacement of the defective products or, at AVERY DENNSON's option, the issuance of a credit or refund in an amount up to the purchase price of the defective product. n no event shall AVERY DENNSON be responsible for claims beyond the purchase price of the defective product. THE WARRANTY SPECFCALLY SET FORTH ABOVE S N LEU OF ANY OTHER WARRANTES, EXPRESS OR MPLED, NCLUDNG, BUT NOT LMTED TO, ANY MPLED WARRANTES OR MERCHANTABLTY, FTNESS FOR ANY PARTCULAR USE AND/OR NON-NFRNGEMENT. AVERY DENNSON SPECFCALLY DSCLAMS AND EXCLUDES ALL OTHER SUCH WARRANTES. N NO EVENT SHALL AVERY DENNSON BE LABLE TO PURCHASER OR ANY OTHER PARTY FOR NDRECT, CONSEQUENTAL, NCDENTAL, SPECAL OR PUNTVE DAMAGES. No representative or agent of AVERY DENNSON is authorized to give any guarantee or warranty or make any representation contrary to the above. No waiver, alteration, addition or modification of the foregoing conditions shall be valid unless made in writing and signed by an executive officer of AVERY DENNSON. Avery Dennison Fasson Roll North America 88 Norton Parkway Mentor, OH (US & Canada) (Mexico)