Fortina Louvers > Wall > Direct Attachment > Interior/Exterior

Transcription

1 Fortina Louvers > Wall > Direct Attachment > Interior/Exterior. Attaching the Back Rail: Measure and mark the position of your Louvers on the wall. Mark and drill pilot holes in the Back Rail in a diameter smaller than the screw you are using. Attach to wall at pre-marked locations. Attach Endcaps to the Louvers with screws provided before installing the Louvers.. Install the Louver by snapping into the Back Rail.. Secure the Louver to the Back Rail with a screw through the side. Attachment screws by others Back Rail Louver with Endcaps installed Secure Louver to Back Rail with screws provided 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

2 Fortina Louvers > Wall > Direct Attachment > Interior/Exterior > Endcaps. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS Louvers. SNAP-ON Endcap For THS Louvers only On exterior vertical installation, drill two small weep holes on the bottom Endcaps. This will allow for any trapped moisture to drain. 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

3 Fortina Louvers > Ceiling > Direct Attachment > Interior Only. Attaching the Back Rail: Measure and mark the position of your Louvers on the ceiling. Mark and drill pilot holes in the Back Rail in a diameter smaller than the screw you are using. Attach to ceiling at pre-marked locations. Attach Endcaps to the Louvers with screws provided, as shown on the next page, before installing the Louvers.. Install the Louver by snapping into the Back Rail.. Secure the Louver to the Back Rail with a screw through the side. Attachment screw by others Back Rail Louver with Endcaps installed Secure Louver to Back Rail with screws provided 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

4 Fortina Louvers > Ceiling > Direct Attachment > Interior Only > Endcaps. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS-Louvers. SNAP-ON Endcap For THS Louvers only 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

5 Fortina Louvers > Wall > Stringer Mounted > Interior/Exterior Stringers come pre-notched for spacing specified.. Attach BTS Bracket to supporting structure. Support structure by others.. Secure L-Stringer to BTS Brackets with the bolts provided. L-Stringer. Assemble the Louvers onto the Stringers with BTP Clips and tighten to fix them. BTS Bracket with attachment bolts provided Attach Endcaps to the Louvers with screws provided, per instruction on next page. Louver BTP Clip 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

6 Fortina Louvers > Wall > Stringer Mounted > Interior/Exterior Installation With Back Plate Visible Back Panel Notch of 5mm or larger Louver Stringer Back Panel Back Rails require cutting a notch, as shown above. Follow instructions mounting Louvers to Stringers. Cut a 5 mm or larger notch at Back Rail to clear installed BTP clip. Secure Back Rails to Louvers with screws through back or sides, as shown at left. Attach Endcaps to the Louvers with screws provided, as shown on the next page. 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

7 Fortina Louvers > Wall > Stringer Mounted > Interior/Exterior > Endcaps. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS-Louvers. SNAP-ON Endcap For THS Louvers only On exterior Vertical installation, drill two small weep holes on the bottom Endcaps. This will allow for any trapped moisture to drain. 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

8 Fortina Louvers > Ceiling > Stringer Mounted > Interior Only STCL- Stringers are pre-notched per spacing specified. Top channel allows for on-site adjustment of hanging point.. Attach the BTS Bracket to your supporting structure. Secure it to the Stringer with bolts provided. The ceiling attachment point can be adjusted by moving bolt along channel before tightening.. Attach Endcaps to Louvers. Assemble Louvers to Stringer with BTP Clips provided and tighten to fix. Supports to structure by others BTS Bracket and bolt STCL- Stringer BTP Clips Louver 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

9 Fortina Louvers > Ceiling > Stringer Mounted > Interior Only > Endcaps. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS-Louvers. SNAP-ON Endcap For THS Louvers only On exterior Vertical installation, drill two small weep holes on the bottom Endcaps. This will allow for any trapped moisture to drain. 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

10 Track light by others Fortina Louvers > Lighting Louvers > Ceiling > Stringer Mounted > Interior Only Lighting Du Cover where does no Stringer Installation Cross Section Lighting Louver TLD-4080 Profiles Needed Installation Cross Section U-Clips LIGHTING LOUVER LOUVER COVER TLD-4080 TLDU Track light by others IMPORTANT: Attaches with U Clips. Screw-on End Cap is available Lighting Duct Louver Cover where Track light does Track not light by occur. others Stringers come pre-notched for spacing specified. Stringer Lighting Duct Louver Cover where Track light does not occur. Stringers U-Clips Lighting Louver Stringers Cover Track by others IMPORTANT: U-Clips needed to attach TLDU-40 Lighting Duct Cover to Louver. Install Stringer Stringers and Louvers Lighting Louver TLD-4080 per instructions. IMPORTANT: U-Clips U-Clips. Assemble Louvers to needed Stringer Lighting to attach Louver TLDU-40 Cover Track by others Lighting with BTP clips provided and Duct Cover Lighting Louver to Louver tighten TLD-4080 to fix.. Locate and attach Track light U-Clips Tracklights by others (by others) into the Louver. Have your Electrician IMPORTANT: connect to power U-Clips source. needed to attach TLDU-40 U-Clips 4.Attach Lighting Lighting Duct Cover (TLDU-40) Duct Cover to the Louver using to Louver U-Clips provided. Tracklight Lighting Duct Louver TLD-4080 Tracklight Track by others Tracklight by others End Cap Lighting Duct Cover TLDU-40 Suspended With Rods Tracklights by others End Cap 5. Attach Endcaps to Louvers. 6. Connect spot lights to track. Note: Coordinating track is Lytespan by Phillips. Lighting Duct Louver TLD-4080 Track by others Lighting Duct Cover TLDU-40 Tracklight by others 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

11 Fortina Louvers > Lighting Louver > Interior Only > Endcaps. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS-Louvers. SNAP-ON Endcap For THS Louvers only On exterior Vertical installation, drill two small weep holes on the bottom Endcaps. This will allow for any trapped moisture to drain. 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

12 Fortina Louvers > Led Light Louver > Stringers > Interior Only. Attach LED rail TLFB-9 to Louver TLF-4080 with screws provided.. Peel off protective tape cover of LED-tube and place securely in LED rail. LED Tube TFLB-9. Clip in Louver Cover Units where needed. Louver TLF Mount Louvers to Stringer per their installation instructions. Transformer and installation of lights by a licensed Electrician. TLFU-40 Louver Cover STCL- Stringer 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

13 Fortina Louvers > Led Light Louver > Interior Only > Endcap. SCREW-ON Endcap For direct attachment TLKS Louvers and all THS-Louvers. SNAP-ON Endcap For THS Louvers only On exterior Vertical installation, drill two small weep holes on the bottom Endcaps. This will allow for any trapped moisture to drain. 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

14 Fortina Louvers > Floor To Ceiling > Interior Only. Mount L-Brackets to floor and ceiling structure.. Take Louver and slide open side into top and bottom brackets and attach with screws provided. (Louver may need to be cut for perfect fit).. Attach Back Rail to Louvers and secure with screws provided. Attachment fasteners by others TBF Brackets Louver Before Installation of Back Plates Back Rail 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

15 Fortina Louvers > Floor To Ceiling > Interior Only > L-Brackets TBF- L/0/50 6 mm 8 mm TBF- L/0/50 0 mm 0 mm USE WITH LOUVERS: THS-040 THS-060 mm mm mm Ø mm 0 mm USE WITH LOUVERS: THS-050 THS mm 5 mm 5 mm Ø mm 0 mm 0 mm 50 mm 5 mm 5 mm 50 mm 5 mm 5 mm mm mm 0 mm 0 mm 8 mm 6 mm 8 mm 6 mm TBF-5 L/0/50 USE WITH LOUVERS: THS-4040 THS mm 5 mm 0 mm Ø mm mm mm TBF-7 L/0/50 USE WITH LOUVERS: THS-5050 THS mm 5 mm 40 mm Ø mm mm mm 0 mm 0 mm 0 mm 40 mm 5 mm 7 mm 7 mm 6 mm 6 mm 5 mm 50 mm 5 mm 50 mm 5 mm 0 mm 0 mm 8 mm 6 mm 8 mm 4 mm TBF- L5/50/75 USE WITH LOUVERS: THS-080 THS-00 THS-05 THS-570 THS mm 8 mm 0 mm 5 mm 50 mm 5 mm 6 mm TBF-4 L5/50/75 USE WITH LOUVERS: THS-075 THS-080 THS-00 THS-05 0 mm 0 mm 0 mm 5 mm 50 mm 5 mm 0 mm mm mm 75 mm 75 mm 5 mm 5 mm 5 mm 5 mm 8 mm 6 mm 8 mm 6 mm 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

16 Fortina Louvers > Floor To Ceiling> Interior Only > L-Brackets TBF-6 L5/50/75 USE WITH LOUVER: THS mm 5 mm 0 mm 5 mm TBF-8 L5/50/75 USE WITH LOUVERS: THS-500 THS-505 THS-505 THS mm 0 mm 0 mm 5 mm 50 mm 0 mm 50 mm 40 mm 7 mm 7 mm 6 mm 6 mm 5 mm 5 mm 5 mm 75 mm 5 mm 75 mm 5 mm 5 mm 8 mm 6 mm 4 mm 8 mm 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

17 Fortina Slats > Ceiling > Interior/Exterior. Install trim piece (if used) to one side of layout.. Starting from the other side, attach (tongue and groove) Slats to surface. 409 Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

18 Fortina Slats > Ceiling > Interior/Exterior Slat > Acessories mm Trims /Edge Treatment M-6 t=. M-9- t=. Exterior Corner Trim M-70 t=. 4 Interior Corner Trim M-78 t= H Joints M-64 t=. 40 M-7 t= mm/mm Corner Trims M-6 t=.5 M-67 t=. M-68 t=. M M-69 t= LONGITUDINAL SECTION USING M-6 LONGITUDINAL SECTION USING M-9- JOINT DETAIL USING M M-9- M64 M-6 CROSS SECTION USING M-6 CROSS SECTION USING M M68 00 Slat > Installation Examples 0 9 (5) M M-9- INSIDE AND OUTSIDE CORNER USING M DROP CEILING DETAIL USING M M-78 5 S M M M Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

19 Fortina Slats > Wall > Interior/Exterior. Attach trim piece at top of installation location on wall.. Insert Slat into trim piece and attach Slat to wall with screws.. Continue mounting the tongue and groove Slats by inserting into the Slat above, so it lodges in place. Install bottom trim piece to wall with screws at correct location to allow the last Slat to be inserted. 4. Install the last slat by sliding it in, up, and down so it rests in bottom trim piece. No need to screws on the bottom Slat Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47

20 Fortina Slats > Wall > Interior/Exterior Slat > Acessories mm Trims /Edge Treatment M-6 t=. M-9- t=. Exterior Corner Trim M-70 t=. 4 Interior Corner Trim M-78 t= H Joints M-64 t=. 40 M-7 t= mm/mm Corner Trims M-6 t=.5 M-67 t=. M-68 t=. M M-69 t= LONGITUDINAL SECTION USING M-6 LONGITUDINAL SECTION USING M-9- JOINT DETAIL USING M M-9- M64 M-6 CROSS SECTION USING M-6 CROSS SECTION USING M M68 00 Slat > Installation Examples 0 9 (5) M M-9- INSIDE AND OUTSIDE CORNER USING M DROP CEILING DETAIL USING M M-78 5 S M M M Chapin Avenue, Burlingame, California 9400 Tel: (800) 50-47