Table of Contents 1/7. Standard Number

Transcription

1 1 C4-04(2014) Standard Specification for Clay Drain Tile and Perforated Clay Drain Tile 2 C12-16a Standard Practice for Installing Vitrified Clay Pipe Lines 3 C14-15a Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe 4 C14M-15a Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe 5 C32-13 Standard Specification for Sewer and Manhole Brick (Made From Clay or Shale) 6 C34-13 Standard Specification for Structural Clay Load-Bearing Wall Tile 7 C55-16 Standard Specification for Concrete Building Brick 8 C56-13 Standard Specification for Structural Clay Nonloadbearing Tile 9 C62-13a Standard Specification for Building Brick (Solid Masonry Units Made From Clay or Shale) 10 C67-16 Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile 11 C73-14 Standard Specification for Calcium Silicate Brick (Sand-Lime Brick) 12 C76-16 Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe 13 C76M-16 Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe 14 C90-16a Standard Specification for Loadbearing Concrete Masonry Units 15 C Standard Specification for Concrete Pipe for Irrigation or Drainage 16 C118M-15 Standard Specification for Concrete Pipe for Irrigation or Drainage 17 C Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units 18 C129-14a Standard Specification for Nonloadbearing Concrete Masonry Units 19 C Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes 20 C140/C140M-17 Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units 21 C Standard Specification for Aggregate for Masonry Mortar 22 C159-06(2016) Standard Specification for Vitrified Clay Filter Blocks 23 C Standard Specification for Structural Clay Facing Tile 24 C Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale) 25 C220-91(2015) Standard Specification for Flat Asbestos-Cement Sheets 26 C221-98(2014) Standard Specification for Corrugated Asbestos-Cement Sheets 27 C222-97(2014) Standard Specification for Asbestos-Cement Roofing Shingles 28 C223-98(2014) Standard Specification for Asbestos-Cement Siding 29 C270-14a Standard Specification for Mortar for Unit Masonry 30 C279-13a Standard Specification for Chemical-Resistant Masonry Units 31 C287-98(2012) Standard Specification for Chemical-Resistant Sulfur Mortar 32 C296/C296M-00(2015) Standard Specification for Asbestos-Cement Pressure Pipe 33 C Standard Test Methods for Vitrified Clay Pipe 34 C315-07(2016) Standard Specification for Clay Flue Liners and Chimney Pots 35 C321-00(2012) Standard Test Method for Bond Strength of Chemical-Resistant Mortars 36 C Standard Specification for Reinforced Concrete Low-Head Pressure Pipe 37 C361M-16 Standard Specification for Reinforced Concrete Low-Head Pressure Pipe 38 C386-93(2012) Standard Practice for Use of Chemical-Resistant Sulfur Mortar 39 C395-01(2012) Standard Specification for Chemical-Resistant Resin Mortars 40 C397-00(2012) Standard Practice for Use of Chemically Setting Chemical-Resistant Silicate and Silica Mortars 41 C398-98(2012) Standard Practice for Use of Hydraulic Cement Mortars in Chemical-Resistant Masonry 42 C399-98(2012) Standard Practice for Use of Chemical-Resistant Resin Mortars 43 C Standard Specification for Aggregates for Masonry Grout 44 C Standard Specification for Industrial Floor Brick 45 C Standard Specification for Concrete Drain Tile 46 C412M-15 Standard Specification for Concrete Drain Tile 47 C414-03(2012) Standard Test Method for Working, Setting, and Service Strength Setting Times of Chemically Setting Chemical-Resistant Silicate and Silica Mortars 48 C425-04(2013) Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings 49 C Standard Test Method for Linear Drying Shrinkage of Concrete Masonry Units 50 C428/C428M-05(2011)e1 Standard Specification for Asbestos-Cement Nonpressure Sewer Pipe 1/7

2 51 C Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets 52 C443M-11 Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets 53 C444-03(2009) Standard Specification for Perforated Concrete Pipe 54 C444M-03(2009) Standard Specification for Perforated Concrete Pipe 55 C458/C458M-98(2011)e1 Standard Test Method for Organic Fiber Content of Asbestos-Cement Products 56 C459/C459M-97(2011)e1 Standard Test Methods for Asbestos-Cement Flat Products 57 C466-03(2012) Standard Specification for Chemically Setting Silicate and Silica Chemical-Resistant Mortars 58 C Standard Specification for Grout for Masonry 59 C478-15a Standard Specification for Circular Precast Reinforced Concrete Manhole Sections 60 C478M-15a Standard Specification for Circular Precast Reinforced Concrete Manhole Sections 61 C479-04(2013) Standard Specification for Vitrified Clay Liner Plates 62 C497-16a Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile 63 C497M-16 Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile 64 C500/C500M-07(2011)e1 Standard Test Methods for Asbestos-Cement Pipe 65 C Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints 66 C505M-15 Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints 67 C506-16b Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe 68 C506M-16b Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe 69 C Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe 70 C507M-16 Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe 71 C508/C508M-00(2015) Standard Specification for Asbestos-Cement Underdrain Pipe 72 C Standard Specification for Structural Clay Nonloadbearing Screen Tile 73 C541/C541M-98(2011)e1 Standard Specification for Linings for Asbestos-Cement Pipe 74 C551/C551M-07(2011)e1 Standard Specification for Asbestos-Cement Fiberboard Insulating Panels 75 C Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale) 76 C Standard Specification for Porous Concrete Pipe 77 C654M-15 Standard Specification for Porous Concrete Pipe 78 C Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe 79 C655M-15 Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe 80 C658-98(2012) Standard Specification for Chemical-Resistant Resin Grouts for Brick or Tile 81 C659-90(2014) Standard Specification for Asbestos-Cement Organic-Foam Core Insulating Panels 82 C663-98(2014) Standard Specification for Asbestos-Cement Storm Drain Pipe 83 C668-98(2014) Standard Specification for Asbestos-Cement Transmission Pipe 84 C Standard Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated 85 C723-98(2012) Standard Practice for Chemical-Resistant Resin Grouts for Brick or Tile 86 C725-90(2014) Standard Specification for Semidense Mineral Fiber Siding 87 C Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units 88 C746-90(2014) Standard Specification for Corrugated Asbestos-Cement Sheets for Bulkheading 89 C780-16a Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry 90 C Standard Terminology Relating to Concrete Pipe and Related Products 91 C825-06(2011) Standard Specification for Precast Concrete Barriers 92 C828-11(2016) Standard Test Method for Low-Pressure Air Test of Vitrified Clay Pipe Lines 93 C Standard Practice for Minimum Structural Design Loading for Underground Precast Concrete Utility Structures 94 C858-10e1 Standard Specification for Underground Precast Concrete Utility Structures 95 C875-98(2014) Standard Specification for Asbestos-Cement Conduit 96 C Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections 97 C877M-16 Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections 2/7

3 98 C Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar 99 C Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water and Wastewater Structures 100 C Standard Practice for Installation of Underground Precast Concrete Utility Structures 101 C Standard Terminology Relating to Clay Products 102 C Standard Specification for Prefabricated Masonry Panels 103 C Standard Specification for Pedestrian and Light Traffic Paving Brick 104 C904-01(2012) Standard Terminology Relating to Chemical-Resistant Nonmetallic Materials 105 C905-01(2012) Standard Test Methods for Apparent Density of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes 106 C Standard Specification for Precast Concrete Water and Wastewater Structures 107 C915-79(2010) Standard Specification for Precast Reinforced Concrete Crib Wall Members 108 C923-08(2013)e1 Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals 109 C923M-08b(2013) Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals 110 C Standard Specification for General Requirements for Prestressed Concrete Poles Statically Cast 111 C936/C936M-16 Standard Specification for Solid Concrete Interlocking Paving Units 112 C Standard Practice for Construction of Dry-Stacked, Surface-Bonded Walls 113 C947-03(2016) Standard Test Method for Flexural Properties of Thin-Section Glass-Fiber-Reinforced Concrete (Using Simple Beam With Third-Point Loading) 114 C948-81(2016) Standard Test Method for Dry and Wet Bulk Density, Water Absorption, and Apparent Porosity of Thin Sections of Glass-Fiber Reinforced Concrete 115 C Standard Test Method for Bond Strength of Mortar to Masonry Units 116 C966-98(2014) Standard Guide for Installing Asbestos-Cement Nonpressure Pipe 117 C969-02(2009) Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines 118 C969M-02(2009) Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines 119 C980-13a Standard Specification for Industrial Chimney Lining Brick 120 C Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe 121 C985M-15a Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe 122 C990-09(2014) Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants 123 C990M-09(2014) Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants 124 C (2013) Standard Test Method for Splitting Tensile Strength of Masonry Units 125 C Standard Test Method for Sampling and Testing Grout 126 C Standard Practice for Inspection of Underground Precast Concrete Utility Structures 127 C e1 Standard Test Methods for Measurement of Masonry Flexural Bond Strength 128 C (2014) Standard Specification for Asbestos-Cement Products Other Than Fill For Cooling Towers 129 C (2014) Standard Specification for Asbestos-Cement Corrugated Fill For Use in Cooling Towers 130 C (2014) Standard Specification for Asbestos-Cement Flat Sheet for Cooling Tower Fill 131 C Standard Specification for Thin Veneer Brick Units Made From Clay or Shale 132 C Standard Specification for Spun Cast Prestressed Concrete Poles 133 C a(2013) Standard Test Method for Hydrostatic Infiltration Testing of Vitrified Clay Pipe Lines 134 C ae1 Standard Practice for Accreditation of Testing Agencies for Masonry 135 C1096/C1096M-07(2011)e1 Standard Test Method for Determination of Wood Fiber in Asbestos Cement 136 C Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines 137 C1103M-14 Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines 138 C (2012) Standard Test Methods for Chemical Resistance and Physical Properties of Carbon Brick 139 C1119/C1119M-90(2015) Standard Test Method for Vacuum Drainage of Asbestos-Cement Mixes 140 C1120/C1120M-98(2011)e1 Standard Test Method for Wash Test of Asbestos 141 C1121/C1121M-04(2015) Standard Test Method for Turner and Newall (T and N) Wet-Length Classification of Asbestos 142 C1122/C1122M-90(2015) Standard Test Method for Wet Volume of Asbestos 3/7

4 143 C1123/C1123M-90(2015) Standard Test Method for Compressibility and Recovery of Asbestos 144 C1124/C1124M-90(2015) Standard Test Method for Kerosene Retention of Asbestos 145 C (2015) Standard Test Method for Penetration Index of Asbestos 146 C (2015) Standard Practice for Least Cost (Life Cycle) Analysis of Concrete Culvert, Storm Sewer, and Sanitary Sewer Systems 147 C (2013) Standard Specification for Extended Life Mortar for Unit Masonry 148 C a(2014) Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar 149 C (2016) Standard Terminology for Non-Asbestos Fiber-Reinforced Cement Products 150 C (2012) Standard Specification for Sulfur Polymer Cement and Sulfur Modifier for Use in Chemical- Resistant, Rigid Sulfur Concrete 151 C (2012) Standard Specification for Chemical-Resistant Carbon Brick 152 C1162/C1162M-90(2015) Standard Test Method for Loose Density of Asbestos 153 C Standard Specification for Clay Roof Tiles 154 C Standard Terminology of Mortar and Grout for Unit Masonry 155 C (2016) Standard Test Methods for Sampling and Testing Non-Asbestos Fiber-Cement Flat Sheet, Roofing and Siding Shingles, and Clapboards 156 C (2016) Standard Specification for Flat Fiber-Cement Sheets 157 C (2011) Standard Test Method for Compressive Strength of Architectural Cast Stone 158 C (2011) Standard Test Method for Absorption of Architectural Cast Stone 159 C a Standard Test Method for In Situ Compressive Stress Within Solid Unit Masonry Estimated Using Flatjack Measurements 160 C a Standard Test Method for In Situ Measurement of Masonry Deformability Properties Using the Flatjack Method Standard Specification for Vitrified Clay Pipe and Joints for Use in Microtunneling, Sliplining, Pipe 161 C1208/C1208M-16a Bursting, and TunnelsC Standard Test Method for Concrete Pipe Sewerlines by Negative Air Pressure (Vacuum) Test Method 162 C1214M-13 Standard Test Method for Concrete Pipe Sewerlines by Negative Air Pressure (Vacuum) Test Method 163 C (2016) Standard Specification for Fiber-Cement Roofing Shingles, Shakes, and Slates 164 C Standard Specification for Precast Concrete Septic Tanks 165 C (2015) Standard Practice for Preparing Coupons for Flexural and Washout Tests on Glass Fiber Reinforced Concrete 166 C (2015) Standard Test Method for Determination of Glass Fiber Content in Glass Fiber Reinforced Concrete (GFRC) (Wash-Out Test) 167 C (2015) Standard Test Method for Performing Tension Tests on Glass-Fiber Reinforced Concrete (GFRC) Bonding Pads 168 C a Standard Terminology of Masonry 169 C (2017) Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill 170 C1244M-11(2017) Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill 171 C Standard Specification for Firebox Brick for Residential Fireplaces 172 C1262/C1262M-16 Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units 173 C b Standard Specification for Heavy Vehicular Paving Brick 174 C Standard Practice for Installing Clay Flue Lining 175 C Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets 176 C (2013) Standard Guide for Design and Construction of Brick Liners for Industrial Chimneys 177 C (2012) Standard Practice for Making and Conditioning Chemical-Resistant Sulfur Polymer Cement Concrete Test Specimens in the Laboratory 178 C Standard Test Method for Compressive Strength of Masonry Prisms 179 C Standard Specification for Concrete Grid Paving Units 180 C Standard Test Method for Examination and Analysis of Hardened Masonry Mortar 181 C Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units 182 C e1 Standard Specification for Architectural Cast Stone 183 C (2012) Standard Test Method for Determining Chemical Resistance of Aggregates for Use in Chemical- Resistant Sulfur Polymer Cement Concrete and Other Chemical-Resistant Polymer Concretes 184 C Standard Specification for Dry-Cast Segmental Retaining Wall Units 4/7

5 185 C a Standard Specification for Admixtures for Masonry Mortars 186 C Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls 187 C Standard Test Method for Rate of Water Absorption of Masonry Mortars 188 C Standard Specification for Glazed Brick (Single Fired, Brick Units) 189 C Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design 190 C1417M-15 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design 191 C b Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers 192 C1433M-16b Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers 193 C1447/C1447M-04(2014) Standard Specification for Non-Asbestos Fiber-Cement Underdrain Pipe 194 C1448/C1448M-05(2014) Standard Specification for Non-Asbestos Fiber-Cement Conduit 195 C1449/C1449M-05a(2014) Standard Specification for Non-Asbestos Fiber-Cement Nonpressure Sewer Pipe 196 C1450/C1450M-04(2014) Standard Specification for Non-Asbestos Fiber-Cement Storm Drain Pipe 197 C (2014) Standard Specification for Performance of Non-Asbestos Fiber-Reinforced Cement Shake, Shingle, and Slate Roofing Systems 198 C (2013) Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals 199 C1478M-08a(2013) Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals 200 C Standard Practice for Installation of Precast Concrete Sewer, Storm Drain, and Culvert Pipe Using Standard Installations 201 C1479M-16 Standard Practice for Installation of Precast Concrete Sewer, Storm Drain, and Culvert Pipe Using Standard Installations 202 C Standard Specification for Concrete Roof Pavers 203 C (2016) Standard Specification for Concrete Roof Tile 204 C Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains 205 C1504M-16 Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains 206 C1530/C1530M-04(2014) Standard Specification for Non-Asbestos Fiber-Cement Roofing Shakes, Shingles, and Slates with Designed Varying Profiles and Thicknesses 207 C Standard Test Methods for In Situ Measurement of Masonry Mortar Joint Shear Strength Index 208 C1532/C1532M-12 Standard Practice for Selection, Removal, and Shipment of Manufactured Masonry Units and Masonry Specimens from Existing Construction 209 C Standard Practice for Capping Concrete Masonry Units, Related Units and Masonry Prisms for Compression Testing 210 C (2016) Standard Test Method for Hot Water Accelerated Aging of Glass-Fiber Reinforced Cement- Based Composites 211 C (2013) Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Mechanical Uplift Resistance Method) 212 C (2016) Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Wind Tunnel Method) 213 C (2016) Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Air Permeability Method) 214 C Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD 215 C (2011) Standard Guide for Quality Assurance of Mortars 216 C1587/C1587M-15 Standard Practice for Preparation of Field Removed Manufactured Masonry Units and Masonry Specimens for Testing 217 C a Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces 218 C Standard Specification for Precast Concrete Grease Interceptor Tanks 219 C Standard Test Method for Concrete Sanitary Sewer Pipe by Negative (Vacuum) or Positive Air Pressure 220 C1618M-13 Standard Test Method for Concrete Sanitary Sewer Pipe by Negative (Vacuum) or Positive Air Pressure 221 C Standard Specification for Elastomeric Seals for Joining Concrete Structures 222 C Standard Specification for Manufactured Concrete Masonry Lintels 223 C Standard Specification for Joints for Concrete Gravity Flow Sewer Pipe, Using Rubber Gaskets 5/7

6 224 C Standard Specification for Concrete Facing Brick 225 C (2011) Standard Specification for Resilient Connectors Between Reinforced Concrete On-Site Wastewater Tanks and Pipes 226 C Standard Test Method for Freeze-thaw and De-icing Salt Durability of Solid Concrete Interlocking Paving Units 227 C Standard Specification for Thin-bed Mortar for Autoclaved Aerated Concrete (AAC) Masonry 228 C1666/C1666M-08(2015) Standard Specification for Alkali Resistant (AR) Glass Fiber for GFRC and Fiber-Reinforced Concrete and Cement 229 C1670/C1670M-16 Standard Specification for Adhered Manufactured Stone Masonry Veneer Units 230 C (2015) Standard Practice for Installation of Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers 231 C a Standard Specification for Joints for Concrete Box, Using Rubber Gaskets 232 C Standard Practice for Installation and Testing of Reinforced Autoclaved Aerated Concrete (AAC) Units 233 C Standard Specification for Unreinforced Autoclaved Aerated Concrete (AAC) Masonry Units 234 C Standard Practice for Construction and Testing of Autoclaved Aerated Concrete (AAC) Masonry 235 C Standard Specification for Autoclaved Aerated Concrete (AAC) 236 C Standard Specification for Reinforced Autoclaved Aerated Concrete (AAC) Elements 237 C1704/C1704M-09a(2016) Standard Test Method for Sampling and Testing Structural Cementitious Panels 238 C1705/C1705M-09(2016) Standard Specification for Structural Cementitious Panels 239 C Standard Specification for Mortars for the Repair of Historic Masonry 240 C1714/C1714M-16 Standard Specification for Preblended Dry Mortar Mix for Unit Masonry 241 C1715/C1715M-15 Standard Test Method for Evaluation of Water Leakage Performance of Masonry Wall Drainage Systems 242 C1716/C1716M-16 Standard Specification for Compression Testing Machine Requirements for Concrete Masonry Units, Related Units, and Prisms 243 C Standard Test Methods for Conducting Strength Tests of Masonry Wall Panels 244 C Standard Test Method for Installed Precast Concrete Tanks and Accessories by the Negative Air Pressure (Vacuum) Test Prior to Backfill 245 C Standard Specification for Concrete Floor Tile 246 C Standard Practice for Installation of Concrete Floor Tiles 247 C1745/C1745M-11 Standard Test Method for Measurement of Hydraulic Characteristics of Hydrodynamic Stormwater Separators and Underground Settling Devices 248 C1746/C1746M-12 Standard Test Method for Measurement of Suspended Sediment Removal Efficiency of Hydrodynamic Stormwater Separators and Underground Settling Devices 249 C Standard Specification for Steel Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe 250 C1776/C1776M-17 Standard Specification for Wet-Cast Precast Modular Retaining Wall Units 251 C a Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer 252 C1781/C1781M-15 Standard Test Method for Surface Infiltration Rate of Permeable Unit Pavement Systems 253 C1782/C1782M-16 Standard Specification for Utility Segmental Concrete Paving Slabs 254 C Standard Specification for Segmental Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD 255 C Standard Specification for Fly Ash Facing Brick 256 C Standard Guide for Reduction of Efflorescence Potential in New Unit Pavement Systems 257 C e1 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures 258 C e1 Standard Specification for Spun Cast Prestressed Concrete Bases for Tapered Steel Lighting Poles 259 C1814/C1814M-16 Standard Test Method for Measurement of Hydraulic Characteristics of Stormwater Filtration Elements 260 C Standard Specification for Synthetic Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe 261 C1821/C1821M-16 Standard Practice for Installation of Underground Circular Precast Concrete Manhole Structures 262 C e1 Standard Test Method for Full Scale Bending Test of Spun Prestressed Concrete Bases for Tapered Steel Lighting Poles 263 C Standard Specification for Production of Dry Cast Concrete Used for Manufacturing Pipe, Box, and Precast Structures 264 D299/D299M-04(2009)e1 Standard Specification for Asbestos Yarns 265 D315/D315M-95(2009)e1 Standard Specification for Woven Asbestos Tape 6/7

7 266 D375/D375M-95(2009)e1 Standard Specification for Asbestos Roving 267 D628/D628M-95(2009)e1 Standard Specification for Asbestos Tubular Sleeving 268 D1061/D1061M-95(2009)e1 Standard Specification for Asbestos Lap 269 D1118/D1118M-95(2009)e1 Standard Test Method for Magnetic Rating of Asbestos Fiber and Asbestos Textiles 270 D1571/D1571M-95(2009)e1 Standard Specification for Woven Asbestos Cloth 271 D1573/D1573M-95(2009)e1 Standard Test Method for Heat Aging of Asbestos Textiles 272 D1918/D1918M-95(2009)e1 Standard Test Method for Asbestos Content of Asbestos Textiles 273 D2100/D2100M-95(2009)e1 Standard Specification for Asbestos Textiles Used for Electrical Insulating Purposes 274 D2589/D2589M-88(2011)e1 Standard Test Method for McNett Wet Classification of Dual Asbestos Fiber 275 D2590/D2590M-98(2011)e1 Standard Test Method for Sampling Chrysotile Asbestos 276 D2752/D2752M-88(2011)e1 Standard Test Methods for Air Permeability of Asbestos Fibers 277 D (2010) Standard Terminology for Asbestos and Asbestos-Cement Products 278 D2947/D2947M-88(2011)e1 Standard Test Method for Screen Analysis of Asbestos Fibers 279 D2985/D2985M-92(2011)e1 Standard Test Method for Color of Asbestos 280 D2987/D2987M-88(2011)e1 Standard Test Method for Moisture Content of Asbestos Fiber 281 D3639/D3639M-92(2011)e1 Standard Test Method for Classification of Asbestos by Quebec Standard Test 282 D (2011) Standard Test Method for Strength Imparted by Asbestos to a Cementitious Matrix 283 D3880/D3880M-90(2009)e1 Standard Test Method for Asbestos Strength Units 284 E514/E514M-14a Standard Test Method for Water Penetration and Leakage Through Masonry 285 E518/E518M-15 Standard Test Methods for Flexural Bond Strength of Masonry 286 E519/E519M-15 Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages 7/7