1/7. Standard Number 17 C126-15

Transcription

1 1 C4-04(2014) Standard Specification for Clay Drain Tile and Perforated Clay Drain Tile 2 C12-14 Standard Practice for Installing Vitrified Clay Pipe Lines 3 C14-15a Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe 4 C14M-15a Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe 5 C32-13 Standard Specification for Sewer and Manhole Brick (Made From Clay or Shale) 6 C34-13 Standard Specification for Structural Clay Load-Bearing Wall Tile 7 C55-14a Standard Specification for Concrete Building Brick 8 C56-13 Standard Specification for Structural Clay Nonloadbearing Tile 9 C62-13a Standard Specification for Building Brick (Solid Masonry Units Made From Clay or Shale) 10 C67-14 Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile 11 C73-14 Standard Specification for Calcium Silicate Brick (Sand-Lime Brick) 12 C76-15a Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe 13 C76M-15 Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe 14 C90-15 Standard Specification for Loadbearing Concrete Masonry Units 15 C Standard Specification for Concrete Pipe for Irrigation or Drainage 16 C118M-15 Standard Specification for Concrete Pipe for Irrigation or Drainage 17 C Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units 18 C129-14a Standard Specification for Nonloadbearing Concrete Masonry Units 19 C Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes 20 C140/C140M-15ae1 Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units 21 C Standard Specification for Aggregate for Masonry Mortar 22 C159-06(2011) Standard Specification for Vitrified Clay Filter Blocks 23 C Standard Specification for Structural Clay Facing Tile 24 C Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale) 25 C220-91(2015) Standard Specification for Flat Asbestos-Cement Sheets 26 C221-98(2014) Standard Specification for Corrugated Asbestos-Cement Sheets 27 C222-97(2014) Standard Specification for Asbestos-Cement Roofing Shingles 28 C223-98(2014) Standard Specification for Asbestos-Cement Siding 29 C270-14a Standard Specification for Mortar for Unit Masonry 30 C279-13a Standard Specification for Chemical-Resistant Masonry Units 31 C287-98(2012) Standard Specification for Chemical-Resistant Sulfur Mortar 32 C296/C296M-00(2015) Standard Specification for Asbestos-Cement Pressure Pipe 33 C Standard Test Methods for Vitrified Clay Pipe 34 C315-07(2011) Standard Specification for Clay Flue Liners and Chimney Pots 35 C321-00(2012) Standard Test Method for Bond Strength of Chemical-Resistant Mortars 36 C361-14a Standard Specification for Reinforced Concrete Low-Head Pressure Pipe 37 C361M-14 Standard Specification for Reinforced Concrete Low-Head Pressure Pipe 38 C386-93(2012) Standard Practice for Use of Chemical-Resistant Sulfur Mortar 39 C395-01(2012) Standard Specification for Chemical-Resistant Resin Mortars 40 C397-00(2012) Standard Practice for Use of Chemically Setting Chemical-Resistant Silicate and Silica Mortars 41 C398-98(2012) Standard Practice for Use of Hydraulic Cement Mortars in Chemical-Resistant Masonry 42 C399-98(2012) Standard Practice for Use of Chemical-Resistant Resin Mortars 43 C Standard Specification for Aggregates for Masonry Grout 44 C Standard Specification for Industrial Floor Brick 45 C Standard Specification for Concrete Drain Tile 46 C412M-15 Standard Specification for Concrete Drain Tile 47 C414-03(2012) Standard Test Method for Working, Setting, and Service Strength Setting Times of Chemically Setting Chemical-Resistant Silicate and Silica Mortars 48 C425-04(2013) Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings 49 C426-15e1 Standard Test Method for Linear Drying Shrinkage of Concrete Masonry Units 50 C428/C428M-05(2011)e1 Standard Specification for Asbestos-Cement Nonpressure Sewer Pipe 1/7

2 51 C Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets 52 C443M-11 Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets 53 C444-03(2009) Standard Specification for Perforated Concrete Pipe 54 C444M-03(2009) Standard Specification for Perforated Concrete Pipe 55 C458/C458M-98(2011)e1 Standard Test Method for Organic Fiber Content of Asbestos-Cement Products 56 C459/C459M-97(2011)e1 Standard Test Methods for Asbestos-Cement Flat Products 57 C466-03(2012) Standard Specification for Chemically Setting Silicate and Silica Chemical-Resistant Mortars 58 C Standard Specification for Grout for Masonry 59 C478-15a Standard Specification for Circular Precast Reinforced Concrete Manhole Sections 60 C478M-15a Standard Specification for Circular Precast Reinforced Concrete Manhole Sections 61 C479-04(2013) Standard Specification for Vitrified Clay Liner Plates 62 C Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile 63 C497M-15 Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile 64 C500/C500M-07(2011)e1 Standard Test Methods for Asbestos-Cement Pipe 65 C Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints 66 C505M-15 Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints 67 C506-16a Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe 68 C506M-16a Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe 69 C Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe 70 C507M-15 Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe 71 C508/C508M-00(2015) Standard Specification for Asbestos-Cement Underdrain Pipe 72 C Standard Specification for Structural Clay Nonloadbearing Screen Tile 73 C541/C541M-98(2011)e1 Standard Specification for Linings for Asbestos-Cement Pipe 74 C551/C551M-07(2011)e1 Standard Specification for Asbestos-Cement Fiberboard Insulating Panels 75 C Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale) 76 C Standard Specification for Porous Concrete Pipe 77 C654M-15 Standard Specification for Porous Concrete Pipe 78 C Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe 79 C655M-15 Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe 80 C658-98(2012) Standard Specification for Chemical-Resistant Resin Grouts for Brick or Tile 81 C659-90(2014) Standard Specification for Asbestos-Cement Organic-Foam Core Insulating Panels 82 C663-98(2014) Standard Specification for Asbestos-Cement Storm Drain Pipe 83 C668-98(2014) Standard Specification for Asbestos-Cement Transmission Pipe 84 C Standard Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated 85 C723-98(2012) Standard Practice for Chemical-Resistant Resin Grouts for Brick or Tile 86 C725-90(2014) Standard Specification for Semidense Mineral Fiber Siding 87 C Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units 88 C746-90(2014) Standard Specification for Corrugated Asbestos-Cement Sheets for Bulkheading 89 C780-15a Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry 90 C Standard Terminology Relating to Concrete Pipe and Related Products 91 C825-06(2011) Standard Specification for Precast Concrete Barriers 92 C Standard Test Method for Low-Pressure Air Test of Vitrified Clay Pipe Lines 93 C Standard Practice for Minimum Structural Design Loading for Underground Precast Concrete Utility Structures 94 C858-10e1 Standard Specification for Underground Precast Concrete Utility Structures 95 C875-98(2014) Standard Specification for Asbestos-Cement Conduit 96 C Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections 97 C877M-02(2009) Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections 2/7

3 98 C Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar 99 C Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water and Wastewater Structures 100 C Standard Practice for Installation of Underground Precast Concrete Utility Structures 101 C Standard Terminology Relating to Clay Products 102 C Standard Specification for Prefabricated Masonry Panels 103 C Standard Specification for Pedestrian and Light Traffic Paving Brick 104 C904-01(2012) Standard Terminology Relating to Chemical-Resistant Nonmetallic Materials 105 C905-01(2012) Standard Test Methods for Apparent Density of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes 106 C Standard Specification for Precast Concrete Water and Wastewater Structures 107 C915-79(2010) Standard Specification for Precast Reinforced Concrete Crib Wall Members 108 C923-08(2013)e1 Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals 109 C923M-08b(2013) Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals 110 C Standard Specification for General Requirements for Prestressed Concrete Poles Statically Cast 111 C936/C936M-15 Standard Specification for Solid Concrete Interlocking Paving Units 112 C Standard Practice for Construction of Dry-Stacked, Surface-Bonded Walls 113 C947-03(2009) Standard Test Method for Flexural Properties of Thin-Section Glass-Fiber-Reinforced Concrete (Using Simple Beam With Third-Point Loading) 114 C948-81(2009) Standard Test Method for Dry and Wet Bulk Density, Water Absorption, and Apparent Porosity of Thin Sections of Glass-Fiber Reinforced Concrete 115 C Standard Test Method for Bond Strength of Mortar to Masonry Units 116 C966-98(2014) Standard Guide for Installing Asbestos-Cement Nonpressure Pipe 117 C969-02(2009) Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines 118 C969M-02(2009) Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines 119 C980-13a Standard Specification for Industrial Chimney Lining Brick 120 C Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe 121 C985M-15a Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe 122 C990-09(2014) Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants 123 C990M-09(2014) Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants 124 C (2013) Standard Test Method for Splitting Tensile Strength of Masonry Units 125 C Standard Test Method for Sampling and Testing Grout 126 C (2015) Standard Practice for Inspection of Underground Precast Concrete Utility Structures 127 C e1 Standard Test Methods for Measurement of Masonry Flexural Bond Strength 128 C (2014) Standard Specification for Asbestos-Cement Products Other Than Fill For Cooling Towers 129 C (2014) Standard Specification for Asbestos-Cement Corrugated Fill For Use in Cooling Towers 130 C (2014) Standard Specification for Asbestos-Cement Flat Sheet for Cooling Tower Fill 131 C Standard Specification for Thin Veneer Brick Units Made From Clay or Shale 132 C Standard Specification for Spun Cast Prestressed Concrete Poles 133 C a(2013) Standard Test Method for Hydrostatic Infiltration Testing of Vitrified Clay Pipe Lines 134 C a Standard Practice for Accreditation of Testing Agencies for Masonry 135 C1096/C1096M-07(2011)e1 Standard Test Method for Determination of Wood Fiber in Asbestos Cement 136 C Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines 137 C1103M-14 Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines 138 C (2012) Standard Test Methods for Chemical Resistance and Physical Properties of Carbon Brick 139 C1119/C1119M-90(2015) Standard Test Method for Vacuum Drainage of Asbestos-Cement Mixes 140 C1120/C1120M-98(2011)e1 Standard Test Method for Wash Test of Asbestos 141 C1121/C1121M-04(2015) Standard Test Method for Turner and Newall (T and N) Wet-Length Classification of Asbestos 142 C1122/C1122M-90(2015) Standard Test Method for Wet Volume of Asbestos 3/7

4 143 C1123/C1123M-90(2015) Standard Test Method for Compressibility and Recovery of Asbestos 144 C1124/C1124M-90(2015) Standard Test Method for Kerosene Retention of Asbestos 145 C (2015) Standard Test Method for Penetration Index of Asbestos 146 C (2015) Standard Practice for Least Cost (Life Cycle) Analysis of Concrete Culvert, Storm Sewer, and Sanitary Sewer Systems 147 C (2013) Standard Specification for Extended Life Mortar for Unit Masonry 148 C a(2014) Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar 149 C (2011) Standard Terminology for Non-Asbestos Fiber-Reinforced Cement Products 150 C (2012) Standard Specification for Sulfur Polymer Cement and Sulfur Modifier for Use in Chemical- Resistant, Rigid Sulfur Concrete 151 C (2012) Standard Specification for Chemical-Resistant Carbon Brick 152 C1162/C1162M-90(2015) Standard Test Method for Loose Density of Asbestos 153 C Standard Specification for Clay Roof Tiles 154 C Standard Terminology of Mortar and Grout for Unit Masonry 155 C (2012) Standard Test Methods for Sampling and Testing Non-Asbestos Fiber-Cement Flat Sheet, Roofing and Siding Shingles, and Clapboards 156 C (2012) Standard Specification for Flat Fiber-Cement Sheets 157 C (2011) Standard Test Method for Compressive Strength of Architectural Cast Stone 158 C (2011) Standard Test Method for Absorption of Architectural Cast Stone 159 C a Standard Test Method for In Situ Compressive Stress Within Solid Unit Masonry Estimated Using Flatjack Measurements 160 C a Standard Test Method for In Situ Measurement of Masonry Deformability Properties Using the Flatjack Method 161 C1208/C1208M-11 Standard Specification for Vitrified Clay Pipe and Joints for Use in Microtunneling, Sliplining, Pipe Bursting, and Tunnels 162 C Standard Test Method for Concrete Pipe Sewerlines by Negative Air Pressure (Vacuum) Test Method 163 C1214M-13 Standard Test Method for Concrete Pipe Sewerlines by Negative Air Pressure (Vacuum) Test Method 164 C (2012) Standard Specification for Fiber-Cement Roofing Shingles, Shakes, and Slates 165 C Standard Specification for Precast Concrete Septic Tanks 166 C (2015) Standard Practice for Preparing Coupons for Flexural and Washout Tests on Glass Fiber Reinforced Concrete 167 C (2015) Standard Test Method for Determination of Glass Fiber Content in Glass Fiber Reinforced Concrete (GFRC) (Wash-Out Test) 168 C (2015) Standard Test Method for Performing Tension Tests on Glass-Fiber Reinforced Concrete (GFRC) Bonding Pads 169 C a Standard Terminology of Masonry 170 C Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill 171 C1244M-11 Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill 172 C Standard Specification for Firebox Brick for Residential Fireplaces 173 C Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units 174 C Standard Specification for Heavy Vehicular Paving Brick 175 C Standard Practice for Installing Clay Flue Lining 176 C Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets 177 C (2013) Standard Guide for Design and Construction of Brick Liners for Industrial Chimneys 178 C (2012) Standard Practice for Making and Conditioning Chemical-Resistant Sulfur Polymer Cement Concrete Test Specimens in the Laboratory 179 C Standard Test Method for Compressive Strength of Masonry Prisms 180 C Standard Specification for Concrete Grid Paving Units 181 C Standard Test Method for Examination and Analysis of Hardened Masonry Mortar 182 C Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units 183 C Standard Test Methods for Evaluating Masonry Bond Strength 184 C Standard Specification for Architectural Cast Stone 185 C (2012) Standard Test Method for Determining Chemical Resistance of Aggregates for Use in Chemical- Resistant Sulfur Polymer Cement Concrete and Other Chemical-Resistant Polymer Concretes 4/7

5 186 C a Standard Specification for Dry-Cast Segmental Retaining Wall Units 187 C a Standard Specification for Admixtures for Masonry Mortars 188 C Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls 189 C Standard Test Method for Rate of Water Absorption of Masonry Mortars 190 C Standard Specification for Glazed Brick (Single Fired, Brick Units) 191 C Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design 192 C1417M-15 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design 193 C a Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers 194 C1433M-16a Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers 195 C1447/C1447M-04(2014) Standard Specification for Non-Asbestos Fiber-Cement Underdrain Pipe 196 C1448/C1448M-05(2014) Standard Specification for Non-Asbestos Fiber-Cement Conduit 197 C1449/C1449M-05a(2014) Standard Specification for Non-Asbestos Fiber-Cement Nonpressure Sewer Pipe 198 C1450/C1450M-04(2014) Standard Specification for Non-Asbestos Fiber-Cement Storm Drain Pipe 199 C (2014) Standard Specification for Performance of Non-Asbestos Fiber-Reinforced Cement Shake, Shingle, and Slate Roofing Systems 200 C (2013) Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals 201 C1478M-08a(2013) Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals 202 C Standard Practice for Installation of Precast Concrete Sewer, Storm Drain, and Culvert Pipe Using Standard Installations 203 C1479M-13 Standard Practice for Installation of Precast Concrete Sewer, Storm Drain, and Culvert Pipe Using Standard Installations 204 C Standard Specification for Concrete Roof Pavers 205 C (2009) Standard Specification for Concrete Roof Tile 206 C Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains 207 C1504M-16 Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains 208 C1530/C1530M-04(2014) Standard Specification for Non-Asbestos Fiber-Cement Roofing Shakes, Shingles, and Slates with Designed Varying Profiles and Thicknesses 209 C Standard Test Methods for In Situ Measurement of Masonry Mortar Joint Shear Strength Index 210 C1532/C1532M-12 Standard Practice for Selection, Removal, and Shipment of Manufactured Masonry Units and Masonry Specimens from Existing Construction 211 C Standard Practice for Capping Concrete Masonry Units, Related Units and Masonry Prisms for Compression Testing 212 C (2009) Standard Test Method for Hot Water Accelerated Aging of Glass-Fiber Reinforced Cement- Based Composites 213 C (2013) Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Mechanical Uplift Resistance Method) 214 C (2009) Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Wind Tunnel Method) 215 C (2009) Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles(Air Permeability Method) 216 C Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD 217 C (2011) Standard Guide for Quality Assurance of Mortars 218 C1587/C1587M-15 Standard Practice for Preparation of Field Removed Manufactured Masonry Units and Masonry Specimens for Testing 219 C a Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces 220 C Standard Specification for Precast Concrete Grease Interceptor Tanks 221 C Standard Test Method for Concrete Sanitary Sewer Pipe by Negative (Vacuum) or Positive Air Pressure 222 C1618M-13 Standard Test Method for Concrete Sanitary Sewer Pipe by Negative (Vacuum) or Positive Air Pressure 223 C Standard Specification for Elastomeric Seals for Joining Concrete Structures 224 C Standard Specification for Manufactured Concrete Masonry Lintels 5/7

6 225 C Standard Specification for Joints for Concrete Gravity Flow Sewer Pipe, Using Rubber Gaskets 226 C Standard Specification for Concrete Facing Brick 227 C (2011) Standard Specification for Resilient Connectors Between Reinforced Concrete On-Site Wastewater Tanks and Pipes 228 C1645/C1645M-15 Standard Test Method for Freeze-thaw and De-icing Salt Durability of Solid Concrete Interlocking Paving Units 229 C Standard Specification for Thin-bed Mortar for Autoclaved Aerated Concrete (AAC) Masonry 230 C1666/C1666M-08(2015) Standard Specification for Alkali Resistant (AR) Glass Fiber for GFRC and Fiber-Reinforced Concrete and Cement 231 C1670/C1670M-15 Standard Specification for Adhered Manufactured Stone Masonry Veneer Units 232 C (2015) Standard Practice for Installation of Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers 233 C a Standard Specification for Joints for Concrete Box, Using Rubber Gaskets 234 C Standard Practice for Installation and Testing of Reinforced Autoclaved Aerated Concrete (AAC) Units 235 C Standard Specification for Unreinforced Autoclaved Aerated Concrete (AAC) Masonry Units 236 C Standard Practice for Construction and Testing of Autoclaved Aerated Concrete (AAC) Masonry 237 C Standard Specification for Autoclaved Aerated Concrete (AAC) 238 C Standard Specification for Reinforced Autoclaved Aerated Concrete (AAC) Elements 239 C1704/C1704M-09a Standard Test Method for Sampling and Testing Structural Cementitious Panels 240 C1705/C1705M-09 Standard Specification for Structural Cementitious Panels 241 C Standard Specification for Mortars for the Repair of Historic Masonry 242 C1714/C1714M-13a Standard Specification for Preblended Dry Mortar Mix for Unit Masonry 243 C1715/C1715M-15 Standard Test Method for Evaluation of Water Leakage Performance of Masonry Wall Drainage Systems 244 C1716/C1716M-14 Standard Specification for Compression Testing Machine Requirements for Concrete Masonry Units, Related Units, and Prisms 245 C Standard Test Methods for Conducting Strength Tests of Masonry Wall Panels 246 C Standard Test Method for Installed Precast Concrete Tanks and Accessories by the Negative Air Pressure (Vacuum) Test Prior to Backfill 247 C Standard Specification for Concrete Floor Tile 248 C Standard Practice for Installation of Concrete Floor Tiles 249 C1745/C1745M-11 Standard Test Method for Measurement of Hydraulic Characteristics of Hydrodynamic Stormwater Separators and Underground Settling Devices 250 C1746/C1746M-12 Standard Test Method for Measurement of Suspended Sediment Removal Efficiency of Hydrodynamic Stormwater Separators and Underground Settling Devices 251 C Standard Specification for Steel Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe 252 C Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer 253 C1781/C1781M-15 Standard Test Method for Surface Infiltration Rate of Permeable Unit Pavement Systems 254 C Standard Specification for Segmental Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD 255 C Standard Specification for Fly Ash Facing Brick 256 C Standard Guide for Reduction of Efflorescence Potential in New Unit Pavement Systems 257 C e1 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures 258 C e1 Standard Specification for Spun Cast Prestressed Concrete Bases for Tapered Steel Lighting Poles 259 C1814/C1814M-16 Standard Test Method for Measurement of Hydraulic Characteristics of Stormwater Filtration Elements 260 C Standard Specification for Synthetic Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe 261 C1821/C1821M-16 Standard Practice for Installation of Underground Circular Precast Concrete Manhole Structures 262 C e1 Standard Test Method for Full Scale Bending Test of Spun Prestressed Concrete Bases for Tapered Steel Lighting Poles 263 D299/D299M-04(2009)e1 Standard Specification for Asbestos Yarns 264 D315/D315M-95(2009)e1 Standard Specification for Woven Asbestos Tape 265 D375/D375M-95(2009)e1 Standard Specification for Asbestos Roving 266 D628/D628M-95(2009)e1 Standard Specification for Asbestos Tubular Sleeving 267 D1061/D1061M-95(2009)e1 Standard Specification for Asbestos Lap 6/7

7 268 D1118/D1118M-95(2009)e1 Standard Test Method for Magnetic Rating of Asbestos Fiber and Asbestos Textiles 269 D1571/D1571M-95(2009)e1 Standard Specification for Woven Asbestos Cloth 270 D1573/D1573M-95(2009)e1 Standard Test Method for Heat Aging of Asbestos Textiles 271 D1918/D1918M-95(2009)e1 Standard Test Method for Asbestos Content of Asbestos Textiles 272 D2100/D2100M-95(2009)e1 Standard Specification for Asbestos Textiles Used for Electrical Insulating Purposes 273 D2589/D2589M-88(2011)e1 Standard Test Method for McNett Wet Classification of Dual Asbestos Fiber 274 D2590/D2590M-98(2011)e1 Standard Test Method for Sampling Chrysotile Asbestos 275 D2752/D2752M-88(2011)e1 Standard Test Methods for Air Permeability of Asbestos Fibers 276 D (2010) Standard Terminology for Asbestos and Asbestos-Cement Products 277 D2947/D2947M-88(2011)e1 Standard Test Method for Screen Analysis of Asbestos Fibers 278 D2985/D2985M-92(2011)e1 Standard Test Method for Color of Asbestos 279 D2987/D2987M-88(2011)e1 Standard Test Method for Moisture Content of Asbestos Fiber 280 D3639/D3639M-92(2011)e1 Standard Test Method for Classification of Asbestos by Quebec Standard Test 281 D (2011) Standard Test Method for Strength Imparted by Asbestos to a Cementitious Matrix 282 D3880/D3880M-90(2009)e1 Standard Test Method for Asbestos Strength Units 283 E514/E514M-14a Standard Test Method for Water Penetration and Leakage Through Masonry 284 E518/E518M-15 Standard Test Methods for Flexural Bond Strength of Masonry 285 E519/E519M-15 Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages 7/7