THE CRAFTSMAN MODEL SILVESTRI GROUP

Transcription

1 05, Inc. DESIGN GRO PROJET # THE RAFTSMAN FOR GRO ANY HANGES TO THESE DRAWINGS MUST BE REPORTED TO DESIGN GRO, IN. IMMEDIATELY IN WRITING. DESIGN GRO, IN ASSUMES NO RESPONSIBILITY FOR HANGES TO THE DRAWINGS THAT ARE NOT REPORTED TO THE ARHITET. LOWER LEVEL PLAN FIRST FLOOR PLAN SEOND FLOOR PLAN (OPTION ) DRAWING INDEX A0-0 A-0 A- A- A-3 A3- A3- A4- E-0 E- E- M-0 M- M- OVER SHEET LOWER LEVEL PLAN FIRST FLOOR PLAN SEOND FLOOR PLAN WALL SETIONS STAIR SETION / WALL BRAING METHOD S-PF GENERAL NOTES / STRUTURAL NOTES / LIGHT AND VENT SHEDULE LOWER LEVEL ELETRIAL PLAN FIRST FLOOR ELETRIAL PLAN SEOND FLOOR ELETRIAL PLAN LOWER LEVEL MEHANIAL PLAN FIRST FLOOR MEHANIAL PLAN SEOND FLOOR MEHANIAL PLAN, LIENSE # EXPIRATION DATE: /3/05 OVER SHEET SALE: N.T.S. A0-0

2 05, Inc. FOUNDATION NOTES ALL 8" FOUNDATION WALLS SHALL HAVE A MINIMUM 6" x 8" ONTINUOUS POURED ONRETE FOOTING. ALL " FOUNDATION WALLS SHALL HAVE A MINIMUM 0" x 8" ONTINUOUS POURED ONRETE FOOTING. REFER TO STRUTURAL NOTES SHEET FOR GENERAL STRUTURE STEEL DIA. PIPE SIZES TO BE: 3" DIA. =.6 (OUTSIDE DIA. = 3.5") & 4" DIA. =.37 (OUTSIDE DIA. = 4.5") BUILDER TO VERIFY THAT ALL STRUTURAL LOADS TRANSFER TO FOUNDATION. EILING HEIGHTS IN BASEMENTS SHALL NOT BE LESS THAN 7-6" LEAR, EXEPT UNDER BEAMS, DUTS OR OTHER OBSTRUTIONS WHERE THE LEAR HEIGHT SHALL BE 6-8" MINIMUM. ALL PREFABRIATED ONRETE LINTELS AT FOOTING LEVEL HANGES SHALL HAVE 8" MINIMUM BEARING AT EAH END. WINDOW WELLS WITH A VERTIAL DEPTH OF 44" SHALL BE EQUIPPED WITH A PERMANENTLY AFIXED LADDER OR STEPS USABLE WITH THE WINDOWS IN THE FULLY OPEN POSITION. LADDER OR RUNGS SHALL HAVE AN INSIDE WIDTH OF AT LEAST 3" FROM THE WALL AND SHALL BE SPAED NOT MORE THAN 8" O.. VERTIALLY FOR THE FULL HEIGHT OF THE WINDOW WEL FOUNDATION WALL REINFORING SALE: /" = -0" MIN. PLANS GRADE /" DIA. ANHOR 6-0" O.. MAX. OR PER DWGS. SEE 6" HEIGHT OF WALL /" LEAR HORIZONTAL REINFORING PER HART VERT. REINFORING PER HART FREE DRAINING GRANULAR FILL DRAIN TILE, SEE WALL SETIONS OPTIONAL FINISHED #4 4" O.. OR 4"x4" ONTINUOUS KEYWAY TO TIE WALL INTO FOUNDATION. NOT REQUIRED IF FLOOR SLAB IS POURED TIGHT TO WALL WALL THIKNESS FOUNDATION WALL DESIGN - POURED WALLS ONRETE = f c MIN.= 3,000 PSI REINFORING fy MIN. = 60,000 PSI MAXIMUM EQUIVALENT SOIL PRESSURE = 55 PSF WALL MAX HEIGHT WALL THIKNESS 8" WALL 0" WALL " WALL 47-0" BATH RI R 8R 7-0" NONE NONE NONE 8-0" 9-0" 0-0" REINFORING 4" O.. 3" O.. 6" O.. NONE 40" O.. NONE NONE 4" O.. 3" O.. HORIZONTAL REINFORING: WALLS LESS THAN OR EQUAL TO 8-0" IN HEIGHT REQUIRE () #4 BAR WITHIN " OF TOP OF WALL AND AT MID HEIGHT. FOR WALLS GREATER THAN 8-0", PROVIDE () #4 BAR WITHIN " OF TOP OF WALL AND AT THIRD POINTS OF THE WAL UNEXAVATED STRUTURAL LEGEND TRUSS / JOIST / RAFTER INDIATOR UNFINISHED ONRETE FOOTER, " DEEP (SEE PLAN FOR SIZE) STEEL OLUMN POINT LOAD LOATION DIRETION OF ROOF PITH UNEXAVATED SEE SHEET A4- FOR STRUTURAL NOTES # DATE ISSUED WITH / HANGE DESRIPTION 57-8" RAFTSMAN GRO LOWER LEVEL PLAN LOWER LEVEL PLAN SALE: /4" = -0" A-0

3 05, Inc SLIDER FLOOR PLAN NOTES ALL DOORS SHALL BE 6" FROM ADJAENT WALL UNLESS NOTED OTHERWISE. LOSET DOORS TO BE ENTERED IN LOSET U.N.O. ALL EXTERIOR AND INTERIOR STUD WALLS TO BE x4 6" O.. U.N.O. ALL DIMENSIONS TO INTERIOR WALLS ARE TO FAE OF STUD. DIMENSIONS TO EXTERIOR WALLS ARE TO FAE OF SHEATHING A READILY AESSIBLE ATTI AESS FRAMED OPENING NOT LESS THAN " x 30" SHALL BE PROVIDED TO ANY ATTI AREA HAVING A LEAR HEIGHT OVER 30". REFER TO STRUTURAL NOTES SHEET FOR GENERAL STRUTURE ALL WORK SHALL BE PERFORMED IN AORDANE WITH ALL APPLIABLE NATIONAL, STATE AND LOAL ODES AND REGULATIONS. ONTRATOR SHALL VERIFY ALL ONDITIONS AND DIMENSIONS AT SITE BEFORE BEGINNING. ANY DISREPANIES SHALL BE REPORTED IMMEDIATELY TO DESIGN GRO IN WRITING FOR JUSTIFIATION AND/OR ORRETION BEFORE PROEEDING WITH WORK. ONTRATORS SHALL ASSUME RESPONSIBILITY FOR ERRORS THAT ARE NOT REPORTED. ALL DIMENSIONS SHALL BE READ OR ALULATED AND NEVER SALED. ONTRATOR SHALL ENSURE OMPATIBILITY OF THE BUILDING WITH ALL SITE REQUIREMENTS. ALL WOOD, ONRETE, AND STEEL MEMBERS SHALL MEET OR EXEED ALL NATIONAL, STATE, AND LOAL BUILDING ODES WHERE APPLIABLE. ALL WOOD IN LOATIONS SUBJET TO TERMITE DEAY SHALL BE PRESSURE TREATED (A) OR BE OF AN APPROVED DEAY RESISTANT SPEIES. THIS INLUDES, BUT IS NOT LIMITED TO, ALL EXTERIOR DEKS, SILLS AND SLEEPERS ON ONRETE OR MASONRY, OR IN DIRET ONTAT WITH GROUND. WALL STUDS SHALL BE ONE PIEE FULL HEIGHT. PROVIDE A MINIMUM OF STUDS AT EAH SIDE OF ALL OPENINGS. ALL BEDROOM WINDOWS SHALL MEET ODE REQUIREMENTS FOR EGRESS. EGRESS LEAR OPENINGS SHALL BE A MINIMUM OF 5.7 SQ. FT. WITH A MINIMUM LEAR OPENING HEIGHT OF 4" AND A MINIMUM LEAR OPENING WIDTH OF 0". SILL HEIGHT SHALL NOT EXEED 44" ABOVE THE FINISH FLOOR. ALL ANGLED WALLS ARE 45 DEGREES U.N.O. DINETTE 5-0" x -" FAMILY 9-8" x 8-5" KITHEN 5-0" x 5-9" DW R 668 PANTRY SHELVES OVEN REF 068 DN 8R STRUTURAL LEGEND L 868 L L L TRUSS / JOIST / RAFTER INDIATOR POWDER " BI-PASS D MUD ROOM/ LAUNDRY 3068 GARAGE -4" x 34-4" ONRETE FOOTER, " DEEP (SEE PLAN FOR SIZE) STEEL OLUMN 3068 W POINT LOAD LOATION 668 DIRETION OF ROOF PITH STUDY 3-0" x -5" PORH SEE SHEET A4- FOR STRUTURAL NOTES # DATE ISSUED WITH / HANGE DESRIPTION RAFTSMAN GRO FIRST FLOOR PLAN,459 S.F. FIRST FLOOR PLAN SALE: /4" = -0" A-

4 05, Inc. FLOOR PLAN NOTES ALL DOORS SHALL BE 6" FROM ADJAENT WALL UNLESS NOTED OTHERWISE. LOSET DOORS TO BE ENTERED IN LOSET U.N.O. ALL EXTERIOR AND INTERIOR STUD WALLS TO BE x4 6" O.. U.N.O. ALL DIMENSIONS TO INTERIOR WALLS ARE TO FAE OF STUD. DIMENSIONS TO EXTERIOR WALLS ARE TO FAE OF SHEATHING A READILY AESSIBLE ATTI AESS FRAMED OPENING NOT LESS THAN " x 30" SHALL BE PROVIDED TO ANY ATTI AREA HAVING A LEAR HEIGHT OVER 30". REFER TO STRUTURAL NOTES SHEET FOR GENERAL STRUTURE ALL WORK SHALL BE PERFORMED IN AORDANE WITH ALL APPLIABLE NATIONAL, STATE AND LOAL ODES AND REGULATIONS. ONTRATOR SHALL VERIFY ALL ONDITIONS AND DIMENSIONS AT SITE BEFORE BEGINNING. ANY DISREPANIES SHALL BE REPORTED IMMEDIATELY TO DESIGN GRO IN WRITING FOR JUSTIFIATION AND/OR ORRETION BEFORE PROEEDING WITH WORK. ONTRATORS SHALL ASSUME RESPONSIBILITY FOR ERRORS THAT ARE NOT REPORTED. ALL DIMENSIONS SHALL BE READ OR ALULATED AND NEVER SALED. ONTRATOR SHALL ENSURE OMPATIBILITY OF THE BUILDING WITH ALL SITE REQUIREMENTS. ALL WOOD, ONRETE, AND STEEL MEMBERS SHALL MEET OR EXEED ALL NATIONAL, STATE, AND LOAL BUILDING ODES WHERE APPLIABLE. ALL WOOD IN LOATIONS SUBJET TO TERMITE DEAY SHALL BE PRESSURE TREATED (A) OR BE OF AN APPROVED DEAY RESISTANT SPEIES. THIS INLUDES, BUT IS NOT LIMITED TO, ALL EXTERIOR DEKS, SILLS AND SLEEPERS ON ONRETE OR MASONRY, OR IN DIRET ONTAT WITH GROUND. WALL STUDS SHALL BE ONE PIEE FULL HEIGHT. PROVIDE A MINIMUM OF STUDS AT EAH SIDE OF ALL OPENINGS. ALL BEDROOM WINDOWS SHALL MEET ODE REQUIREMENTS FOR EGRESS. EGRESS LEAR OPENINGS SHALL BE A MINIMUM OF 5.7 SQ. FT. WITH A MINIMUM LEAR OPENING HEIGHT OF 4" AND A MINIMUM LEAR OPENING WIDTH OF 0". SILL HEIGHT SHALL NOT EXEED 44" ABOVE THE FINISH FLOOR. ALL ANGLED WALLS ARE 45 DEGREES U.N.O. 9-0" EILING W.I MASTER BATH -0" EILING MASTER BEDROOM 5-4" x 8-7" 48"x48" PAN BENH 668 BATH 068 BI-FOLD LINEN BEDROOM -4" x -0" 36"x36" PAN LINEN " WALL HEIGHT DN R 7R 8-0" EILING 668 OPEN BELOW L L 668 DN 7R W.I.. BONUS ROOM 5-8" x -" STRUTURAL LEGEND " EILING TRUSS / JOIST / RAFTER INDIATOR " WALL HEIGHT ONRETE FOOTER, " DEEP (SEE PLAN FOR SIZE) BEDROOM -0" x -8" BATH BEDROOM -6" x -6" STEEL OLUMN POINT LOAD LOATION DIRETION OF ROOF PITH SEE SHEET A4- FOR STRUTURAL NOTES # DATE ISSUED WITH / HANGE DESRIPTION RAFTSMAN GRO SEOND FLOOR PLAN,600 S.F. SEOND FLOOR PLAN SALE: /4" = -0" A-

5 05, Inc. NOTES. ONTRATOR TO DETERMINE NUMBER, SIZE AND LOATION OF DOWNSPOUTS PER APPLIABLE ODE(S) FOR PROPER ROOF DRAINAGE.. PROVIDE RIKETS AS NEESSARY FOR PROPER WATER DRAINAGE 3. REFER TO STRUTURAL NOTES SHEET FOR GENERAL STRUTURE 4. TRUSS MANUFATURER TO ENSURE TRUSSES ARE DESIGNED SO THAT FASIA S ALIGN PER. 5. ALL RAFTERS SHALL BE NAILED TO EILING JOISTS TO FORM A ONTINUOUS TIE BETWEEN EXTERIOR WALLS WHERE JOISTS ARE PARALLEL TO THE RAFTERS. WHERE NOT PARALLEL, RAFTERS SHALL BE TIED WITH A RAFTER TIE, LOATED AS NEAR THE PLATE AS PRATIAL RAFTER TIES SHALL NOT BE SPAED MORE THAN 4-0" O... RAFTERS SHALL BE FRAMED TO RIDGE BOARD, OR TO EAH OTHER, WITH GUSSET PLATES AS A TIE. 6. RIDGE BOARDS SHALL BE AT LEAST " NOMINAL THIKNESS AND NOT LESS IN DEPTH THAN THE UT END OF THE RAFTER. WHEN THE UT END OF THE RAFTER EXEEDS /4" THE RIDGE BOARD SHALL BE ONSTRUTED OF A SOLID x WITH AN ADDITIONAL x (AS REQ D) FURRED TO THE BOTTOM EDGE OF THE x. 7. VALLEY AND HIP RAFTERS SHALL NOT BE LESS THAN " NOMINAL THIKNESS AND NOT LESS IN DEPTH THAN THE UT ENDS OF THE RAFTERS. 8. HIP AND VALLEY RAFTERS SHALL BE SPORTED AT THE RIDGE BY A BRAE TO A SPORTING PARTITION WALL, OR BE DESIGNED TO ARRY/ DISTRIBUTE THE SPEIFI LOAD AT THAT POINT. 9. FALSE HIMNEYS, DORMERS, OLAS, AND OTHER SIMILAR FEATURES, SHOULD NOT BE FRAMED AS A BOX ON THE ROOF. THE BOX SHOULD BE FRAMED DOWN INTO THE ROOF TO EILING JOIST LEVEL AND STRUTURALLY TIED INTO THE ADJAENT RAFTERS AND EILING JOISTS, OR TRUSSES. THE EXTERIOR SHEATHING SHOULD EXTEND DOWN TO THIS LEVEL OTHER THAN WHERE A METAL FLU NEEDS TO GO THROUGH FROM THE FIREBOX. STRUTURAL LEGEND TRUSS / JOIST / RAFTER INDIATOR ONRETE FOOTER, " DEEP (SEE PLAN FOR SIZE) STEEL OLUMN POINT LOAD LOATION DIRETION OF ROOF PITH SEE SHEET A4- FOR STRUTURAL NOTES # DATE ISSUED WITH / HANGE DESRIPTION RAFTSMAN GRO SALE: /4" = -0" A-3

6 05, Inc. WINDOW DETAIL x6 TRIM WINDOW WINDOW FRONT ONLY FALSE SHUTTERS EL = 9-7/8" x4 TRIM 6-0" A.F.F. OLUMN DETAIL EL = - 3/4" FINISH SEOND FLOOR EL = 0 - /8" 6-0" A.F.F. EL = 00-0" 0" 8-6" VERIFY IN FIELD GRADE, OORDINATE IN FIELD, TYP. EL = 88-6 /8" 3 /" REAR ELEVATION ELEVATION LEGEND DIMENSIONAL SINGLES SYNTHETI STONE VENEER HORIZONTAL SIDING BOARD AND BATTEN SIDING EL = 9-7/8" 6-0" A.F.F. 4-0" # DATE ISSUED WITH / HANGE DESRIPTION EL = - 3/4" EL = 0 - /8" FINISH SEOND FLOOR 6-0" A.F.F. RAFTSMAN GRO EL = 00-0" 0" GRADE, OORDINATE IN FIELD, TYP. SYNTHETI STONE WATER TABLE W/ STONE AP TO BOTTOM OF WINDOW FRONT ELEVATION EL = 88-6 /8" SALE: /4" = -0"

7 05, Inc. WINDOW DETAIL x6 TRIM WINDOW EL = 9-7/8" WINDOW FRONT ONLY FALSE SHUTTERS x4 TRIM 6-0" A.F.F. OLUMN DETAIL EL = - 3/4" FINISH SEOND FLOOR EL = 0 - /8" 6-0" A.F.F. EL = 00-0" 0" 8-6" VERIFY IN FIELD GRADE, OORDINATE IN FIELD, TYP. SYNTHETI STONE WATER TABLE W/ STONE AP TO BOTTOM OF WINDOW EL = 88-6 /8" 3 /" RIGHT ELEVATION ELEVATION LEGEND DIMENSIONAL SINGLES SYNTHETI STONE VENEER HORIZONTAL SIDING BOARD AND BATTEN SIDING EL = 9-7/8" 6-0" A.F.F. # DATE ISSUED WITH / HANGE DESRIPTION EL = - 3/4" EL = 0 - /8" FINISH SEOND FLOOR 6-0" A.F.F. RAFTSMAN GRO EL = 00-0" GRADE, OORDINATE IN FIELD, TYP. LEFT ELEVATION EL = 88-6 /8" SALE: /4" = -0"