EC800 Ultra Fast 2.1 Clearcoat NEW Quart Pack Size

Transcription

1 EXHIBIT D-1

2 EXHIBIT D-2

3 EC800 Ultra Fast 2.1 Clearcoat NEW Quart Pack Size March 2013 Product Information: EC800 Ultra Fast 2.1 Clearcoat is now available in a convenient quart pack size. This new pack size offers all of the same features nefits users have come to expect from EC800. Accompanying this new clear pack size is ECH8075 Clearcoat Hardener ECA83 Accelerated Reducer Stard. Both of these are now available in the 8Z pack size which rounds out the components of this popular clearcoat kit. EC800 is an ultra fast, high gloss 2.1 VOC highly productive clearcoat designed specifically for use the ENVIROBASE basecoat system. This clearcoat, its no bake requirement zero flash tween coats, dramatically reduces cycle times while maintaining the quality appearance required by high production shops. From an environmental stpoint, the low 2.1 VOC of EC800 Clearcoat along the high solids resin also decreases clearcoat material usage therefore greatly reduces the overall VOC emissions. Marketing Information: EC800 is designed for use on repairs of 1 4 panels. Easy 3 part mix ratio 4 parts EC800 Ultra Fast 2.1 Clearcoat 1 part ECH8075 Clearcoat Hardener 1 part ECA 81 or ECA 83 Accelerated Reducer Reference Envirobase product data sheet EB 800, for complete mix application recommendations Designed for use over Envirobase Waterborne Basecoat No Flash Time Between Coats S Polish in as little as 30 Minutes Excellent Gloss Appearance Maximize Booth Utilization Ordering Information: EC800 ECH8075 ECA83 Size: 04 8Z 8Z Container: Round Quart Accupour Accupour Packaging: 6 per case 12 per case 12 per case EXHIBIT D-3 ENVIROBASE is a registered trademark of PPG Industries Ohio, Inc.

4 Product Code EC800 ECH8075 ECA83 PPG Ordering Code EC ECH8075 8Z ECA83 8Z Product Launch # Retail Pkg Qty: 1 unit 1 unit 1 unit Pkg Unit of Measure: Carton Carton Carton Retail Pkg Dimensions: x x x x 4.46 Retail Pkg Unit Weight (lbs): 2.60 lbs 0.92 lbs 0.92 lbs Minimum Purchase Quantity Per Each: Each Each Each Containers per Case: Case Dimensions: x x /16 x 8 x 4 5/ /16 x 8 x 4 5/8 Containers per Pallet: Pallet Size: 42 x x x 42 Pallet Height: Cases Per Layer: Point of Sale Description: See first page See first page See first page UPC/Bar Code Lal: (Per product code size) UPC/Bar Code Carton: (Per product code size) Country of Origin: USA USA USA *Package VOC Regulatory: 2.30 lbs/gal (276 g/l).73 lbs/gal (87 g/l) 7.06 lbs/gal (846 g/l) *Package VOC Actual: 1.17 lbs/gal (140 g/l).51 lbs/gal (61 g/l).63 lbs/gal (75 g/l) Shipping Description: UN1263, Paint, 3, PG II, limited quantity UN1263, Paint, 3, PGIII, Ltd Qty UN1263, PAINT RELATED MATERIAL, 3, PGII, LTD QTY Flash Point: 2 F 98 F 6 F Hazard Class Lals/Placards: None None NONE Physical State: Liquid Liquid LIQUID NFPA: NFPA Hazard Class IB, Class B Extinguisher NFPA Hazard Class IC, Class B Extinguisher NFPA Hazard Class IB, Class B Extinguisher Chemical Abstract No.: NA NA NA Chemical Components: Please see MSDS, section 3 Please see MSDS, section 3 Please see MSDS, section 3 VAPOR HARMFUL: Please see MSDS, section 2 Please see MSDS, section 2 Please see MSDS, section 2 EXHIBIT D-4 ENVIROBASE is a registered trademark of PPG Industries Ohio, Inc.

5 EXHIBIT D-5

6 EXHIBIT D-6

7 EXHIBIT D-7

8 EXHIBIT D-8

9 EXHIBIT D-9

10 EXHIBIT D-10

11 Product Information Product Information Product Information Product Information Product Description ENVIROBASE Waterborne ECS21 White, ECS25 Gray, ECS27Basecoat Black LV Sealer ENVIROBASE Waterborne Basecoat ECS21 White, ECS25 Gray, ECS27 Black LV Sealer Product Description LV Sealer ESC21, are premium quality, wet on wet sealers specifically for use ECS21 White, ECS25 Gray, Waterborne ECS27 Black Product Description Basecoat. LV Sealer under ENVIROBASE Envirobase is a premium waterborne color system for use in repair repainting of motor Product Description Envirobase Description is a premium waterborne color system for use in repair repainting of motor Product This fast drying LV Sealerishas superior flow properties excellent vehicles. Industry leading color capability easily achieved when applied as part topcoat of a twoholdout. or three-stage LV Sealer ESC21, 25 are premium quality, wet on wetas sealers for use vehicles. Industry leading color capability is27easily achieved when applied part ofspecifically a two or three-stage A variety of grays can achieved by intermixing of the three packaged sealers. basecoat/clearcoat paint process. Mixed Envirobase color reproduces the original OEM Waterborne Basecoat. under ENVIROBASE basecoat/clearcoat paint process. Mixed Envirobase color reproduces the original OEM Product Description The sealers can applied over un-sed OEM e-coat, sed original finishes /or properly solid, metallic, mica or XIRALLIC paint finish of virtually all OEM manufacturer s worldwide. paint finish of virtually all OEM manufacturer s worldwide. solid, metallic, mica or XIRALLIC Sealer ESC21, 27 are premium quality, wet on wet sealers specifically for use prepared LV treated bare steel,25 aluminum, firglass plastic. This fast drying LV Sealer superior flow properties excellent topcoat holdout. Envirobase products are has engineered to reduce volatile organic compounds (VOC) will Waterborne Basecoat. under ENVIROBASE Envirobase of products areachieved engineered to reduceofvolatile organic compounds by intermixing the three packaged sealers. (VOC) will exceed Aallvariety of today s legislativegrays VOCcan restrictions throughout the United States Canada. exceedthis all of today s restrictions throughout the United States /or Canada. The sealers canlegislative appliedvoc over un-sed OEM e-coat, sed original finishes properly fast drying LV Sealer has superior flow properties excellent topcoat holdout. Preparation of Substrate Envirobase waterborne color system is also capable of producing internal color as well as prepared treated bare steel, aluminum, firglass plastic. A variety of grays can achieved by intermixing of the three packaged sealers. Envirobase waterborne color system alsosoap capable of producing internal color as well as In all cases,information, wash all surfaces to paintedis water, thenfor apply the appropriate interior The color. For additional see Envirobase product bulletins EB145 interior color over un-sed OEM e-coat, sed original finishes /or properly EB510 sealers can applied Cleaner Ensure that the substrate is thoroughly cleanedfor dried both interior color. For ONECHOICE additional information, see Envirobase product bulletins EB145 interior color EB510 for internal color. treated bare steel, aluminum, firglass plastic. prepared after preparation work. for internal color. fore Preparation of Substrate PREPARATION OF SUBSTRATE PREPARATION OFcases, SUBSTRATE In all wash all surfaces to painted soapp400 water, apply the (dry) appropriate PREPARATION OF SUBSTRATE Original Paintwork should sed using / U.S. then 360 grit discs or Cleaner Ensure that the substrate is thoroughly cleaned dried ONECHOICE Preparation of Substrate P600 / U.S. 400 grit paper (wet). Exposed metal should spot-primed both a Apply over original baked finishes or over recommended undercoats. fore after preparation work. In all cases, wash allprimer surfaces tolow). painted soap water, then apply the appropriate suitable bare metal (see Apply over original baked finishes or over recommended undercoats. ONECHOICE Cleaner Ensure that the substrate is thoroughly cleaned dried both Original Paintwork should sed using P400 rust-free / U.S.water. 360 grit discs (dry) or an In all cases, wash all surfaces to painted soap Final clean fore after preparation work. Aluminum, Bare Steel Galvanized Steel must clean, abraded thoroughly In all cases, wash all400 surfaces to painted soapshould water. Final clean an P600 / U.S. grit paper (wet). Exposed metal spot-primed a appropriate waterborne cleaner. Ensure that the substrate is thoroughly cleaned dried using P180 / U.S.cleaner. 180 to P280 / U.S. 240 gritispaper (wet).these appropriate waterborne Ensure that the substrate thoroughly cleaned dried suitable bare metal primer (see low). fore starting repair. Original Paintwork should sed using P400 discs (dry) is or substrates must primed an etch pimer. Additional film/ U.S. build360 overgrit etch primers fore starting repair. P600 / U.S. 400 grit paperof(wet). Exposed should LV spot-primed a strongly recommended, a minimum 1.5 mils of the metal Sealer must applied Aluminum, Bare Steel Galvanized Steel must clean, rust-free abraded thoroughly suitable bare metal primer (see low). in two coats. Apply Envirobase after sing P / using P180 / U.S. 180 to / U.S. 240 grit paper (wet).these Apply Envirobase afterp280 sing P / U.S must 600 grade paper orry s P600 -over 800etch / U.S is600 grade substrates primed etch pimer. Additional film build primers U.S Bare 600 Steel grade paper or thoroughly dry s P / U.S grade Aluminum, Galvanized Steel must clean, rust-free abraded thoroughly Electrodeposition Primer must cleaned may then directly overcoated paper. strongly recommended, asealer minimum 1.5 milsp280 of the LV Sealer must applied paper. using P180 LV / U.S. 180 as to / U.S. 240 gritabrading. paper (wet).these the A -Chromatic aofwet-on-wet Sealer out in two coats. substrates must primed an etch pimer. Additional film build over etch primers is Wash off residues adry thoroughly re-cleaning LV appropriate waterborne strongly recommended, minimum 1.5 fore mils of the Sealer must applied Polyester Body Fillers should dryof sed using 280 / U.S. 240 grit paper. Wash off residues dry thoroughly fore re-cleaning appropriate waterborne substrate cleaner. The must use of tack rag iscleaned recommended. Electrodeposition Primer athoroughly may then directly overcoated in two coats. substrate cleaner. The use of a tack rag is recommended. the A -Chromatic LV Sealer as ased Wet-on-Wet Sealer out Fir Glass SMC should dry using P280abrading. / U.S. 240 grit paper. Electrodeposition Primer must thoroughly cleaned may then directly overcoated Polyester should as dry using Sealer 280 abrading. /au.s. paper. theshould A Body -Chromatic LV Sealer ased Wet-on-Wet out Plastic Fillers dry sed P600 / U.S. 400 (use finer240 grit grit for softer plastics) primed first a PPG Plastic Adhesion Promoter. Fir Glass Fillers SMC should dry sed P280 / U.S. 240grit gritapaper. Before mixing, gently h-shake bottles the toners for few seconds Polyester Body shouldof dryenvirobase sed using using 280 / U.S. 240 Before mixing, gently h-shake bottles ofthe Envirobase toners for paper. a few seconds fore use. Do not place toners or mixed color on shaker or mechanically agitate. fore use. Do not place toners or mixed color on shakerp600 or mechanically agitate. for use Plastic should SMC dry sed dry / U.S. 400 P280 (use a/ U.S. finerdesigned grit for Fir Glass should sed using 240 gritsofter paper. Mixed Envirobase color should thoroughly h-stirred fore application. If not used plastics) primed firstcolor ashould PPG Plastic Adhesion h-stirred Promoter. Mixed Envirobase thoroughly fore application. If not used immediately it should h-stirred again fore use. Plastic should dry sed immediately it should h-stirred again fore use. P600 / U.S. 400 (use a finer grit for softer plastics)paint primed first adesigned PPG Plastic Promoter. paintdesigned for use Use nylon 125 micron filters specially for Adhesion use waterborne materials. Use nylon 125 micron paint filters specially designed for use waterborne paint materials. Designed for use EB-200 8/ PPG Industries EB-200Information 8/14 Product 2012 PPG Industries ENVIROBASE Waterborne Basecoat Industries 2012 PPG Industries 2014 PPG 2014 PPG Industries EXHIBIT D-11 EB-200 8/14EB-143 6/14 Product Description EB-143 6/14 EB-200 8/14 Envirobase is a premium waterborne color system for us vehicles. Industry leading color capability is easily achieved when applied a basecoat/clearcoat paint process. Mixed Envirobase colo

12 APPLICATION GUIDE Mixing Ratio ECS2x LV Sealer : EH391/EH392 Hardener : D87xx/DT18xx Thinner : 4 Vols. 1 Vol. 1 Vol. Thinner Selection D8764 : Fast Compliant Thinner DT1845 Cool Temperature D8774 : Medium Compliant Thinner DT1850 Medium Temperature D8767 : Slow Compliant Thinner DT1855 Hot Temperature Potlife 1 70 F (21 C) Additives SLV814 Universal Flexibilizer Ready-to-Spray ECS2x LV Sealer: SLV814: 10 Vols 1 Vol Spraygun set-up Fluid Tip Spray Viscosity Spray pressure HVLP at air cap Conventional at spray gun Numr of coats 1-2 coats Film build per wet coat Dried film build per coat Flash off at 70ºF / 21ºC Between coats Before baking mm or equivalent seconds #2 70 F (21 C) 10 PSI PSI 2.5 mils 1.0 mils 5-10 minutes 5-10 minutes Before topcoating Drying times Dust-free 70ºF / 21ºC 10 minutes Dry to hle 70ºF / 21ºC 1 hour Tape Time 70ºF / 21ºC 1½ hours F (21 C) for 1 coat F (21 C) for 2 coats After 72 hours, sealer must sed. If sed film is low 1 mil, sealer must reapplied. IR (Infrared) IR medium wave IR short wave 10 minutes 5 minutes EXHIBIT D-12 2 EB-200 8/14

13 Overcoat / Recoat Envirobase Grade wet Grade dry F (21 C) for 1 coat F (21 C) for 2 coats Note: After 72 hours, sealer must sed. If sed film is low 1 mil, sealer must reapplied. P1000 / U.S. 500 grade paper P1000 / U.S. 500 grade paper Guidelines The use of HVLP spray equipment can give an increase in transfer efficiency of around 25% depending upon the make model of equipment use. For all substrates except un-sed electrodeposition primer, ensure that the surface is thoroughly sed to the panel edge or to a distance several centimeters yond the damaged area, whichever is the smaller. Do not attempt spot repair on original or refinish thermoplastic applications, lacquer or 1K finishes. Partially used cans of hardener must carefully closed. Technical Data Total dry film build: Minimum 25μm / 1.0 mil Maximum 37μm / 1.5 mils Film build per wet coat 2.5 mils / 62.5μ Dried film build per coat 1.0 mils / 25μ Theoretical coverage. Theoretical coverage in sq.ft./us gal. ready-to-spray (RTS), 1.0 mil dry film thickness 550 sq. ft.per US gal Percent solids by volume RTS 34.5% ECS2x: EH391: D87xx/DT18xx ECS2x: EH392: D87xx/DT18xx ECS2x: EH391: D87xx/DT18xx ECS2x: EH392: D87xx/DT18xx RTS Combinations: + SLV814 + SLV814 Volume Ratio: 4 : 1 : 1 4 : 1 : 1 4 : 1 : % 4 : 1 : % Applicable Use Category Primer Primer Primer Primer VOC Actual (g/l) VOC Actual (lbs/gal) VOC Regulatory (less water less exempt) (g/l) VOC Regulatory (less water less exempt) (lbs/gal) Density (g/l) Density (lbs/gal) Volatiles wt. % Water wt. % Exempt wt. % Water vol. % Exempt vol. % EB-200 8/14 EXHIBIT D-13 3 EB-200 8/14

14 Gray Mixing Chart LV Sealers This chart can used to mix the LV Sealer. The G1 - G7 ratios will help to achieve tter hiding when used as a guide for mixing the LV Sealer. Mix Ratio By Volume Mix Ratio By Cumulative Weight Grams Parts Mix Ratio ½ Pint Quart ½ Pint Quart ECS G1 EH39X D87xx/DT18xx ECS G2 ECS25 Mix By EH39X Weight Only D87xx/DT18xx ECS G3 ECS EH39X D87xx/DT18xx ECS G4 ECS EH39X D87xx/DT18xx G5 ECS EH39X D87xx/DT18xx ECS G6 ECS EH39X D87xx/DT18xx G7 ECS EH39X D87xx/DT18xx EXHIBIT D-14 4 EB-200 8/14

15 Health Safety See Material Safety Data Sheet Lals for additional safety information hling instructions. The contents of this package may have to blended other components fore the product can used. Before opening the packages, sure you underst the warning messages on the lals MSDS of all the components, since the mixture will have the hazards of all its parts. Improper hling use, for example, poor spray technique, inadequate engineering controls /or lack of proper Personal Protective Equipment (PPE), may result in hazardous conditions or injury. Follow spray equipment manufacturer's instructions to prevent personal injury or fire. Provide adequate ventilation for health fire hazard control. Follow company policy, product MSDS respirator manufacturer s recommendations for selection proper use of respiratory protection. Be sure employees are adequately rained on the safe use of respirators per company regulatory requirements. Wear appropriate PPE such as eye skin protection. In the event of injury, see first aid procedures on MSDS. Always observe all applicable precautions follow good safety hygiene practices. EXHIBIT D-15 5 EB-200 8/14

16 Emergency Medical or Spill Control Information (412) ; In Canada (514) Materials descrid are designed for application by professional, trained personnel using proper equipment are not intended for sale to the general public. Products mentioned may hazardous should only used according to directions, while observing precautions warning statements listed on lal. Statements methods descrid are based upon the st information practices known to PPG Industries. Procedures for applications mentioned are suggestions only are not to construed as representations or warranties as to performance, results, or fitness for any intended use, nor does PPG Industries warrant freedom from patent infringement in the use of any formula or process set forth herein Envirobase; OneChoice; Deltron are trademarks Global of Refinish PPG industries System, Ohio, H 2O-So-Clean Inc. are trademarks of PPG Industries Ohio, Inc. Xirallic is a registered trademark of Merck Kgaa This document This document was printed was printed on on recycled recycled paper. paper. PPG Industries Progress Drive Strongsville, OH PPG Canada Inc Royal Windsor Drive, Unit #6 Mississauga, Ontario L5J 1K PPG Industries EXHIBIT D-16 6 EB-200 8/14

17 PRIMER - SPRAYED - Actual VOC emitted per gallon EXHIBIT D-17

18 PRIMER SURFACER - SPRAYED - Actual VOC emitted per gallon Technical Data (Cont.) RTS Combinations: ECP1X : EH391 ECP1X : EH391: D8764/74/67 ECP1X : EH391: D8764/74/67 + SLV814 Volume Ratio: 4 : 1 4 : 1 : 1 4 : 1 : % Applicable Use Category Primer Primer Primer VOC Actual (g/l) VOC Actual (lbs/gal) VOC Regulatory (less water less exempt) (g/l) VOC Regulatory (less water less exempt) (lbs/gal) Density (g/l) Density (lbs/gal) Volatiles wt. % Water wt. % Exempt wt. % Water vol. % Exempt vol. % EXHIBIT D-18 EB /09