Precise Aerial Roof Measurement Report

Transcription

1 Precise Aerial Roof Measurement Report Prepared for you by RC Roofing & heet Metal LLC 6101 Morriss Rd, Flower Mound, TX RC Roofing & heet Metal LLC 01 W. Walcott t. Pilot Point, TX 7658 Rico Lara tel

2 TABLE OF CONTENT Images...1 Length Diagram... Pitch Diagram...5 Area Diagram...6 Notes Diagram...7 Penetrations Diagram...8 Report ummary...9 MEAUREMENT In this D model, facets appear as semi-transparent to reveal overhangs. Total Roof Area =60,9 sq ft Total Roof Facets =7 Predominant Pitch =0/1 Number of tories >1 Total Ridges/Hips =867 ft Total Valleys =609 ft Total Rakes =78 ft Total Eaves =1,608 ft Total Penetrations =6 Total Penetrations Perimeter = 58 ft Total Penetrations Area = 69 sq ft PREPARED FOR Contact: Rico Lara Company: RC Roofing & heet Metal LLC Address: 01 W. Wacott t. Pilot Point, TX 7658 Phone: Measurements provided by

3 IMAGE The following aerial images show different angles of this structure for your reference. Top View PAGE 1

4 IMAGE North ide outh ide PAGE

5 IMAGE East ide West ide PAGE

6 15 LENGTH DIAGRAM Total Line Lengths: Ridges = 7 ft Hips = 95 ft Valleys = 609 ft Rakes = 78 ft Eaves = 1,608 ft Flashing = 18 ft tep flashing = 799 ft Parapets = 1,59 ft EagleView Technologies, Inc E N W Note: This diagram contains segment lengths (rounded to the nearest whole number) over 5 feet. In some cases, segment labels have been removed for readability. Plus signs preface some numbers to avoid confusion when rotated (e.g. +6 and +9). PAGE

7 PITCH DIAGRAM Pitch values are shown in inches per foot, and arrows indicate slope direction. The predominant pitch on this roof is 0/ F 1 1 F F F F 017 EagleView Technologies, Inc F E N W Note: This diagram contains labeled pitches for facet areas larger than 0 square feet. In some cases, pitch labels have been removed for readability. Blue shading indicates a pitch of /1 and greater. Gray shading indicates flat, 1/1 or /1 pitches. If present, a value of "F" indicates a flat facet (no pitch). PAGE 5

8 AREA DIAGRAM Total Area = 60,9 sq ft, with 7 facets EagleView Technologies, Inc E N W Note: This diagram shows the square feet of each roof facet (rounded to the nearest foot). The total area in square feet, at the top of this page, is based on the non-rounded values of each roof facet (rounded to the nearest square foot after being totaled). PAGE 6

9 NOTE DIAGRAM Roof facets are labeled from smallest to largest (A to Z) for easy reference. AM AL AK AF AE AZ BO J H Q M N G RI BT BL BM DF B V Z AA T Y AB U AE C A L K P O AI BI AR AX AQ AP AOAY AT AU AWAV BP BR B BGBH BQ AN BN 017 EagleView Technologies, Inc. BE BD BF BC BJ BABB X W AD AC AG AH AJ BK E N W PAGE 7

10 PENETRATION NOTE DIAGRAM Penetrations are labeled from smallest to largest for easy reference. Total Penetrations = 6 Total Penetrations Perimeter = 58 ft Total Penetrations Area = 69 sq ft Total Roof Area Less Penetrations = 59,870 sq ft EagleView Technologies, Inc. E N W PAGE 8

11 W E REPORT UMMARY Areas per Pitch Roof Pitches 0/1 1/1 /1 /1 /1 1/1 18/1 Area (sq ft) % of Roof.% 1.6%.8% 6.8% 1.% 1.1% 19.1% The table above lists each pitch on this roof and the total area and percent (both rounded) of the roof with that pitch. Waste Calculation Table Waste % 0% 10% 1% 15% 17% 0% % Area (sq ft) 60,9 66,7 67,580 69,90 70,597 7,07 7,61 quares This table shows the total roof area and squares (rounded up to the nearest decimal) based upon different waste percentages. The waste factor is subject to the complexity of the roof, individual roofing techniques and your experience. Please consider this when calculating appropriate waste percentages. Note that only roof area is included in these waste calculations. Additional materials needed for ridge, hip, valley, and starter lengths are not included. Penetrations Area (sq ft) Perimeter (ft) Any measured penetration smaller than x feet may need field verification. Accuracy is not guaranteed. The total penetration area is not subtracted from the total roof area. Total Roof Facets = 7 Total Penetrations =6 N 017 EagleView Technologies, Inc. Lengths, Areas and Pitches Ridges = 7 ft (7 Ridges) Hips = 95 ft (5 Hips). Valleys = 609 ft ( Valleys) Rakes * = 78 ft (50 Rakes) Eaves/tarter ** = 1,608 ft (68 Eaves) Drip Edge (Eaves + Rakes) =,9 ft (118 Lengths) Parapet Walls = 1,59 (9 Lengths). Flashing = 18 ft (1 Lengths) tep flashing = 799 ft (8 Lengths) Total Area = 60,9 sq ft Total Penetrations Area = 69 sq ft Total Roof Area Less Penetrations = 59,870 sq ft Total Penetrations Perimeter = 58 ft Predominant Pitch = 0/1 Property Location Longitude = Latitude = Notes This was ordered as a commercial property. There were no changes to the structure in the past four years. Parapet Wall Area Table Wall Height (ft) * Rakes are defined as roof edges that are sloped (not level). ** Eaves are defined as roof edges that are not sloped and level. PAGE 9

12 Vertical Wall Area This table provides common parapet wall heights to aid you in calculating the total vertical area of these walls. Note that these values assume a 90 degree angle at the base of the wall. Allow for extra materials to cover cant strips and tapered edges. Online Maps Online map of property Directions from RC Roofing & heet Metal LLC to this property Mound,TX, PAGE 10