CRESTON FAMILY DENTISTRY Addendum #3 June 26, 2014

Transcription

1 CRESTON FAMILY DENTISTRY: ADDENDUM #3 JUNE 26, 2014 CRESTON FAMILY DENTISTRY Addendum #3 June 26, 2014 Creston, Iowa The following items have been assembled as changes, corrections, clarification to the drawings and specifications for this project dated February 27, These changes shall be a part of the contract documents and bids for this project and shall include all costs or credits involved with these items. Contractors shall acknowledge this addendum on their bid proposal form. Changes, corrections or clarifications to the DRAWINGS and SPECIFICATIONS include the following: GENERAL NOTES: 1. General Contractor s Bidders List: No other bids will be accepted. Breiholz Construction, Des Moines IA, , domf@breiholz.com Cornerstone Contractors, Corning IA, , Jason.kentner@cornercc.com Downing Construction, Indianola IA, , kens@downingconstruct.com 2. Addendum #4 will be out early next week. Lower level HVAC ducts will have a few modifications. 3. Clarification: All cabinets and countertops are by Owner. EXCEPTION: Reception Desk countertop, as per noted in drawing details shall be p-lam and by General Contractor. 4. Grace Ice Water Shield or ICF manufacturers recommendation, below grade to footing and up wall 12 above grading, to be compatible with ICF insulation and approved by Architect. 5. REFERENCE Stone Sill and Horizontal Stone look on drawings: A. Stone to set on ICF Brick Ledge blocks. See attached drawings Addendum #3 Sheets 3-1, 3-2 (typical). B. See Stone Cladding Specification Section (See attached) 6. Clarification: Aluminum Doors to be narrow style. 7. Design loads for the entire office area on the main level is 50 psf. The joists noted give a deflection limit of L/600 for floor rigidity and to meet the Commercial Floor Deflection Limit. 1 o f 2 LAUGERMAN ARCHITECTS, INC. ADDENDUM #3

2 CRESTON FAMILY DENTISTRY: ADDENDUM #3 JUNE 26, 2014 REFERENCE PROJECT MANUAL: Reference Specifications A. ADD Section Stone Cladding (See Attached) B. ADD Section Air Barrier (See Attached) C. ADD Section Luxury Vinyl Tile (See Attached) D. REFERENCE Section Table of Contents a. ADD Section Stone Cladding, 2 PGS b. ADD Section Air Barrier, 7 PGS c. ADD Section Luxury Vinyl Tile, 17 PGS E. REFERENCE Section Insulating Concrete Forming, Part 2, Item 2.01, a. ADD (as approved product) Nudura Insulated Concrete Form Wall Systems. Contact , vstevenart@nudura.com b. ADD (as approved product) Flexx Block Insulated Concrete Forms, Contact , dhall@liteform.com F. REFERENCE Section Glazing, Part 2, Item 2.01, ADD (as approved product) Yates & Yates Glass , afton@yatesglass.com G. REFERENCE Section Signage, Part 1, Item 1.01 a. DELETE #2 Letters and hardware necessary to install exterior cast letters. b. ADD #2 To include ADA required: restroom signage, entry signage, and egress signage. REFERENCE LARGE ARCHITECTURAL DRAWINGS: 1. REFERENCE Sheet A2.1, East Elevation, DELETE Stone above overhead garage doors. See Attached Addendum #3 Sheets 3-3, 3-4 East Elevation revision. 2. NOTE: Full set, ADD brick ledge ICF block to foundation walls in to support exterior stone cladding. See Addendum #3 Sheets 3-1, 3-2 (typical). a. Brick Ledge block shall be below grad with stone extending below grade min. 6 b. Grace Ice water shield or equal shall extend from footing to above grade, up wall 12. c. ICF manufacturer block size shall determine footing depth (designed with 16 ¾ block heights), with a minimum footing bearing at 4-0 below grade and step down accordingly along perimeter of building. 3. REFERENCE SHEET A5.0 Vinyl Sheet Flooring See Attached Section END OF DOCUMENT 2 o f 2 LAUGERMAN ARCHITECTS, INC. ADDENDUM #3

3 page 1 Waterford Stone Masonry Unit Specifications Part 1: General Submittal A. Submit product literature, unit shop drawings, certification, test reports, full size sample(s) of each color selected Quality Assurance A. All high density concrete masonry units shall be Waterford Stone masonry units manufactured by an Oldcastle Company. All units shall conform to ASTM C90-11b and shall have a hand chiseled finish with a range of colors as specified. B. Field Constructed Mock-up: Construct a sample panel, no less than 4 x 4, of units of the color to be used in the project. The cleaning agent and method should also be determined and applied at the same time the sample panel is constructed Delivery, Storage and Handling A. Concrete Stone Masonry Veneer: Waterford Stone Masonry Units as manufactured and distributed by Oldcastle Companies. B. Solid units with physical dimensions and characteristics complying with ASTM C55-11 and the physical properties of ASTM C568/C568M-10, Class II. C. Color: Minimum of three variegated color blending as selected from manufacturer s standard selections. D. Size: 4 inches in width nominal with face dimensions selected from a minimum of 15 face sizes to match ashlar pattern indicated on drawings or established in the approved mock-up. E. Anchors: Provide anchors to suit design requirements for material and installation requirements. F. Mortar Materials: Provide mortar to suit design requirements for material and installation requirements Project/Site Conditions and Handling A. Cover walls each day after installation to keep open walls protected and dry. Part 2: Products Product Name A. Waterford Stone Masonry Units Manufacturer A. Oldcastle Architectural 900 Ashwood Parkway, Suite 600 Atlanta, GA (PH) (FAX) Part 3: Execution Laying Masonry Walls A. Coursings: Install masonry construction anchored solidly to backing, properly aligned, plumb and true in required layout, making straight, level courses, unless otherwise indicated. 01. Place varying size of stones to provide a random ashlar pattern as approved. 900 Ashwood Parkway, Suite 600, Atlanta, GA Oldcastle. All Rights Reserved. ART

4 page Maintain mortar joint thickness of 3/8 (10mm) to 3/4 (19mm) either horizontally or vertically. 03. Tool joints as follows: a. Flush b. Concave c. Recessed B. Placing and Bonding: Lay masonry in full bed of mortar with full head joints, properly jointed with other work. Buttering corners of joints, deep or excessive furrowing of mortar joints is not permitted. 01. Back-bevel bed joints to remove excess mortar droppings in cavity as work progresses. 02. Fully bond intersections and external corners. 03. Isolate masonry partitions from vertical structural framing members with a control joint as indicated. 04. Provide for expansion and control joints as indicated on the drawings. 05. Do not adjust masonry units after placing. Where resetting of masonry is required, remove, clean units, and place in new mortar. 06. Leave joints under shelf angles and elsewhere as indicated or required open to receive sealant. C. Anchors: Provide anchors to suit design requirements indicated or required. 01. Masonry backing: Wire anchors or adjustable anchors. Minimum spacing 18 inches (450 mm) horizontally and 32 inches (800 mm) vertically. 02. Steel stud backing: Adjustable anchors attached with corrosion-resistant screws having a minimum nominal shank diameter of 0.19 inch (4.8 mm). Minimum spacing 18 (450 mm) horizontally and 32 (800 mm) vertically. 03. Wood stud backing: Corrugated sheet metal anchors, wire anchors or adjustable anchors. Attach to backing with a corrosion-resistant 8d common nail, or a fastener with equivalent or greater pullout strength. Minimum spacing 18 inches (450 mm) horizontally and 32 inches (800 mm) vertically. 04. Increase quantity of wall ties around perimeter of openings, at wall terminations and corners, and along parapet walls, placed within 8 inches (203 mm) of openings and edges of masonry. D. Built-in items furnished by other trades, and leave accurate openings necessary for subsequent installation of other work to maintain required strength and appearance of masonry construction. 01. Fill solidly with mortar around conduit and sleeves passing through masonry work. 02. Build-in loose steel angle lintels, providing bearing indicated in full mortar bed. E. Prevent grout, mortar, and soil from staining face of masonry. Remove grout and mortar from these surfaces immediately. F. Protect base of masonry walls from rain splashed mud and mortar splatters. G. Install weep holes in veneer masonry at maximum 24 (610 mm) on center horizontally above through-wall flashing, above shelf angles, lintels, bottom of walls, and elsewhere as indicated on drawings. H. Do not permit mortar to drop or accumulate into cavity air space or to plug weeps Installation A. Lighting: Provide adequate lighting for masonry work by placing all lighting a reasonable distance from the wall for even illumination. Do not use trough lighting. B. Cutting: Make all unit cuts, including those for bonding, holes, boxes, etc., with motor driven masonry saws, using either an abrasive or diamond blade. Cut neatly for best appearance. 900 Ashwood Parkway, Suite 600, Atlanta, GA Oldcastle. All Rights Reserved. ART

5 page Inspection A. The facing shall be free from chips, cracks, crazes or any other imperfection that would detract from the overall appearance of the finished wall when viewed from a distance of fifteen (15) feet at right angles to the wall with normal lighting Flashing of Masonry Work A. Install flashing at locations shown in the plans and in strict accordance with the details and the best masonry flashing practices Weep Holes and Vents A. Install weep holes and vents at proper intervals (32 O.C.) at courses above grade, above flashing, and at any water stops (32 O.C.) over windows, doors, and beams Cleaning A. Keep walls clean daily during installation using brushes, rags, and burlap squares. Do not allow excess mortar lumps or smears to harden on the finished surfaces. Remove green mortar with burlap or a dry cloth. Harsh cleaning methods after walls have been erected may mar the surface of the units Final Clean down A. No acid or acid base solutions shall be used in the cleaning of Waterford Stone units. A detergent masonry cleaner shall be used following the manufacturer s instructions and the surface shall be thoroughly rinsed with clean water Maintenance A. Waterford Stone units, when properly installed and cleaned, need virtually no maintenance other than routine cleaning with standard commercial grade cleaning agents. Graffiti, paint or dye stains may need special cleaning methods and products. Contact manufacturer for specific cleaning recommendations Installation Recommendations A. Cavity wall construction is recommended for exterior walls, with proper flashing, venting and weep holes. B. A complimentary or matching mortar color is recommended when using Waterford Stone units. C. A water repellent mortar additive is highly recommended for all exterior walls. D. Control joint spacing should be approximately max. and located at inside corners, 2-4 from outside corners, wall height changes and at one or both sides of windows or large openings Limitations A. The facing is not intended for use as an impervious surface. B. Muriatic acid should not be used as a cleaning agent or in direct contact with the facing. C. The facing should not be continuously exposed to temperatures above 250 F. END OF SECTION 900 Ashwood Parkway, Suite 600, Atlanta, GA Oldcastle. All Rights Reserved. ART

6 PROSOCO R-GUARD Spray Wrap Fluid-Applied Membrane Air & Water-Resistive Barrier Specification Specifier Note: The information provided below is intended to guide the Architect in developing specifications for products manufactured by PROSOCO, Inc. and should not be viewed as a complete source of information about the product(s). The Architect should always refer to the Product Data Sheet and MSDS for additional recommendations and for safety information Specifier Note: Paragraphs below are for PART 2 PRODUCTS, Manufacturers and Products. Manufacturer: PROSOCO, Inc., 3741 Greenway Circle, Lawrence, KS Phone: (800) ; Fax: (785) CustomerCare@prosoco.com Product Description PROSOCO R-GUARD Spray Wrap is a fluid applied air and water-resistive barrier that stops air and water leakage in cavity wall, masonry veneer construction, as well as in stucco, EIFS and most other building wall assemblies. The easily applied liquid quickly dries into a rubberized, highly durable, water-resistant, vapor-permeable membrane. R-GUARD Spray Wrap provides superior protection against water intrusion while minimizing potential for condensation within walls and allowing accumulated moisture to dry while reducing energy costs and lowering the risk of mold and mildew. R-GUARD Spray Wrap is compatible with most paints, sealants and selfadhered waterproofing or air barrier components. Use PROSOCO R-GUARD Spray Wrap as a high-performing water-resistive barrier or as part of a continuous, building-wide air barrier system. Appropriate for vertical, above-grave applications to exterior sheathing, CMU, cast concrete and most other common building materials. TYPICAL TECHNICAL DATA FORM: light red, viscous liquid, mild odor SPECIFIC GRAVITY: greater than 1.0 ph: 7.5 to 10.0 WEIGHT/GALLON: 12.7 pounds ACTIVE CONTENT: No Data TOTAL SOLIDS: 62 percent by volume (ASTM D2369) VOC CONTENT: 28 grams per Liter. Complies with all known national, state and district AIM VOC regulations. FLASH POINT: greater than 200 degrees Fahrenheit (greater than 93 degrees Celsius) FREEZE POINT: 32 degrees Fahrenheit (0 degrees Celsius) SHELF LIFE: 1 year in tightly-sealed, unopened container Limitations Do not apply when surface or air temperatures are below 40 degrees Fahrenheit (4 degrees Celsius) or above 110 degrees Fahrenheit (43 degrees Celsius). Many gypsum sheathing products require additional material to achieve hide and the desired mil thickness for a pinhole free coating. Actual coverage rates must be determined through mock-up applications. Not for application below-grade or in locations designed to be continuously immersed in water. Specifier Note: Paragraphs below are for PART 3 EXECUTION, Installation. SPECIFIER NOTE: Prepare all joints, seams cracks, fastener penetrations and rough openings prior to application of the primary air barrier. See appropriate product data sheets and R- GUARD Installation Guidelines for more information.

7 Installation Before applying, read Preparation and Safety Information sections in the Manufacturer s Product Data Sheet for PROSOCO R-GUARD Spray Wrap. Refer to the Product Data Sheet for additional information about application. Do not dilute or alter R-GUARD Spray Wrap, except for use in sprayers. The product may need thinning with up to 5 percent fresh water, based on surface, drying conditions and equipment. Mix well before use with a low-speed drill and clean mixing paddle. Avoid mixing air into the membrane. Application: Exterior Sheathing (Gypsum, Plywood, OSB) 1. Spray or roller apply sufficient Spray Wrap to achieve a continuous, pinhole free coating. Some gypsum sheathing will require additional material due to varying substrate porosity. 2. When spray applying, back roll as necessary to ensure there are no pinholes, voids or gaps in the membrane. 3. Inspect membrane before covering. Repair any punctures or damaged areas by applying additional Spray Wrap. Overlap repairs, penetration treatments, transitions, rigid flashing and other air barrier components to ensure positive drainage and continuity of the air and water-resistive barrier. Application: CMU Wall Construction 1. Spray or roller apply sufficient Spray Wrap to fill and cover the entire face of the exterior wall assembly. Let dry. 2. Spray or roller-apply a second coat of Spray Wrap to achieve hide. The finished application must be continuous and free of voids and pinholes. Back roll spray application to achieve a void- and pinhole-free surface. Take special care to achieve full coverage around wall ties or surface irregularities. 3. Inspect membrane before covering. Repair any punctures or damaged areas by applying additional Spray Wrap. Overlap repairs, penetration treatments, transitions, rigid flashing and other air barrier components to ensure positive drainage and continuity of the air and water-resistive barrier. Curing and Drying Complete drying times vary with temperature, humidity and surface conditions. Protect from rain or freezing until completely dry. At 70 F (21 C) and 50% relative humidity, R-GUARD Spray Wrap dries to touch and can be over coated in 2-4 hours. Coverage Coverage rates may vary depending on surface porosity, moisture uptake and other factors. Unless otherwise required by the referenced test method, performance test results were achieved when the product was applied at 10 wet mils to DensGlass gold fiberglass mat gypsum sheathing. Many gypsum sheathing products require additional material to achieve hide and the desired mil thickness for a pinhole free coating. Actual rates must be determined through mockup applications. Exterior Gypsum Board, OSB & Plywood: 50 to 100 square feet per gallon CMU: 30 to 60 square feet per gallon per coat Cleanup Clean tools and equipment with water immediately after use. Dried material must be removed mechanically.

8 Thermal & Moisture Protection Air Barriers Fluid Applied Membrane Air Barriers Air Barrier Coatings Weather Barriers PRODUCT DATA SHEET Spray Wrap fluid-applied air & water-resistive barrier R-GUARD Spray Wrap is part of the family of PROSOCO R-GUARD products developed to prevent the unwanted movement of water and air through building envelopes. Utilize Spray Wrap as the primary air barrier over above grade wall assemblies prepared with R-GUARD Joint & Seam Filler and FastFlash. OVERVIEW PROSOCO R-GUARD Spray Wrap is a fluid-applied air and water-resistive barrier that stops air and water leakage in cavity wall, masonry veneer construction, as well as in stucco, EIFS and most other building wall assemblies. Once on the substrate, the easily applied liquid quickly dries into a rubberized, highly durable, water-resistant, vapor-permeable membrane. Compared to self-adhered or mechanically-fastened sheet wraps, easy-to-use R-GUARD Spray Wrap provides superior protection against water intrusion, while minimizing potential for condensation within walls. R-GUARD Spray Wrap minimizes the potential for condensation and allows accumulated moisture to dry while reducing energy costs and lowering the risk of mold and mildew. Use Spray Wrap as a high-performing water-resistive barrier or as part of a continuous, building-wide air barrier system. The durable membrane conforms and adheres to common building surfaces and is compatible with most paints, sealants and selfadhered waterproofing or air barrier components. Appropriate for vertical, above-grade applications to exterior sheathing, CMU, cast concrete and most other common building materials. SPECIFICATIONS For all PROSOCO product specifications visit www. prosoco.com. ADVANTAGES Reduces condensation and energy loss caused by air leaks through the wall assembly. Minimizes risk of water damage to sheathing and associated repair or replacement costs. Allows moisture which accumulates within the wall assembly to dry. Fast and easy installation reduces labor costs. No air leakage or water intrusion between the sheathing and R-GUARD Spray Wrap stable under air and wind pressure loads. Seamless no tears, holes, or improperly lapped joints to compromise performance. Combines the durability and flexibility of a rubberized coating with the speed and ease of a water-based, fluid-applied application. Won t tear or lose effectiveness when exposed to weather during construction. May be exposed to weather for up to 6 months without compromising performance. Time-saving, single component is easy to install with conventional spray equipment. Long pot life. Water cleanup. Color Coded simplifies inspection and quality control. Low odor and non-toxic. Complies with all VOC regulations. Compatible with most paints, sealants and coatings. Limitations Not for use at surface or air temperatures below 40 F (4 C) or above 110 F (43 C) unless Hot Weather Precautions are followed. See Surface and Air Temperatures. Not for use below-grade or in locations which are designed to be continuously immersed in water. REGULATORY COMPLIANCE VOC Compliance PROSOCO R-GUARD Spray Wrap is compliant with the following national, state and district AIM VOC regulations: X US Environmental Protection Agency X California Air Resources Board SCM Districts X South Coast Air Quality Management District X Maricopa County, AZ X Northeast Ozone Transport Commission Product Data Sheet Page 1 of 4 Item #70010 RGSW PROSOCO

9 PRODUCT DATA SHEET Spray Wrap TYPICAL TECHNICAL DATA R-GUARD SPRAY WRAP FORM SPECIFIC GRAVITY >1.0 WT/GAL ACTIVE CONTENT Light red viscous liquid, mild odor ph lbs No Data TOTAL SOLIDS 62% by volume ASTM D 2369 VOC CONTENT FLASH POINT FREEZE POINT 28 g/l >200 F (>93 C) 32 F (0 C) SHELF LIFE 1 year in tightly sealed, unopened container Performance When Applied at 10 Wet Mils* Air Infiltration Air Leakage of Air Barrier Assembly Meets and exceeds air barrier performance requirements (ASTM E2178) Passed: L / s m 2 at 75 Pa (ASTM E2357) Water Penetration No water penetration (ASTM E331) (Static Pressure) Fastener No water infiltration (ASTM D1970) Sealability Flame Spread: 15 (ASTM E84) Smoke Developed: 40 Surface Buring NFPA and ICC Class A Building Material *Unless otherwise required by the referenced test method, test results cited were achieved when the product was applied at 10 wet mils to DensGlass gold fiberglass mat gypsum sheathing. Please obtain the PROSOCO R-GUARD Spray Wrap Product Test Results sheet for a complete list of performance test results. Illustrations depiciting the use of PROSOCO R-GUARD products are available at by downloading the R-GUARD Installation Guidelines. PREPARATION To ensure best results, apply to clean surfaces free of contaminants. Chemical residues, surface coatings or films may adversely affect adhesion. Protect people, vehicles, property, plants and all other surfaces not intended to receive Spray Wrap. Remove and replace damaged sheathing. Surfaces to be coated must be continuous. On exterior sheathing, repair cracks larger than ½ inch. On CMU or concrete, fill cracks larger than ½ inch with mortar. Consult a structural engineer for all moving cracks, and repair as needed. Fill, Bridge & Flash Uses: R-GUARD GypPrime + R-GUARD Joint & Seam Filler + R-GUARD FastFlash 1. Fill surface defects and over driven fasteners with R-GUARD Joint & Seam Filler. Fill open joints, seams and cracks measuring up to ½ inch (13 mm) with R-GUARD Joint & Seam Filler. 2. Consolidate and seal cut edges of gypsum board sheathing in rough openings with fast-drying R-GUARD GypPrime. Gun and spread R-GUARD Joint & Seam Filler into all inside corners, cracks, open joints and seams in rough openings. Allow Joint & Seam Filler to skin over. 3. Gun and spread R-GUARD FastFlash to create an opaque, monolithic flashing membrane over the inside of all rough openings and extending 4 6 inches ( mm) over the face of the exterior wall assembly. Allow FastFlash to skin over. Use FastFlash to create a continuous waterproof membrane which is free of voids or pinholes. See individual product data sheets and R-GUARD Installation Guidelines for more information. Let all joint and seam fillers and rough opening treatments skin over before applying R-GUARD Spray Wrap. Surface and Air Temperatures Surface and ambient temperatures should be 40 F (4 C) and rising and below 110 F (43 C) during application and drying. Wind and high temperatures will accelerate drying. ALWAYS TEST ALWAYS TEST a small area of each surface to confirm suitability and desired results before starting overall application. Test with the same equipment, recommended surface preparation and application procedures planned for general application. Hot Weather Precautions: If air or surface temperatures exceed 95 F (35 C), apply to shaded surfaces and before daytime air and surface temperatures reach their peak. Hot surfaces may be cooled with a mist of fresh water. Surfaces may be damp but must be free of standing water before application. Keep containers closed and out of direct sunlight when not in use. Cover open pails with a wet towel as needed to prevent skinning. Equipment Mix R-GUARD Spray Wrap with a low-speed drill and clean mixing paddle. When roller applying, use a 3/4 inch (19 mm) nap roller. R-GUARD Spray Wrap is compatible with GRACO and Titan airless spray equipment with the following specifications: Minimum 1 gallon per minute output. Minimum hose width of 3/8 inch. NOTE: A ¼ x 3 whip hose may be used for ergonomic purposes. Run 3/8 ID hose all the way to the 3 whip hose. Minimum tip size of Minimum pressure requirement to spray of 2,000 psi at the gun with an airless sprayer rated no lower than 3,300 psi. Remove all filters in sprayer and gun before application. Product Data Sheet Page 2 of 4 Item #70010 RGSW PROSOCO

10 Spray Wrap PRODUCT DATA SHEET Storage and Handling Store in a cool dry place. Keep container tightly closed when not dispensing. Do not open container until preparation work is complete. Do not mix or alter with other chemicals. When stored at or below 80 F (27 C) R-GUARD Spray Wrap has a shelf life of 12 months after the date of manufacture. This shelf life assumes upright storage of factory sealed containers. Do not double stack pallets. Dispose of unused product and containers in accordance with local, state and federal regulations. APPLICATION Before use, read Preparation and Safety Information. Dilution & Mixing Do not dilute or alter, except for use in sprayers. The product may need thinning with up to 5 percent fresh water, based on surface, drying conditions and equipment. Mix well before use with a low-speed drill and clean mixing paddle. Avoid mixing air into the membrane. Coverage Rates Coverage rates will vary depending on surface porosity, moisture uptake, and other factors. Unless otherwise required by the referenced test method, test results cited on the Product Test Data were achieved when the product was applied at 10 wet mils to DensGlass gold fiberglass mat gypsum sheathing. Many gypsum sheathing products require additional material to achieve hide and the desired mil thickness for a pinhole free coating. In some cases two coats may be required. Actual rates must be determined through mock-up applications. For more information regarding coverage rates as it pertains to glass-mat sheathing, please consult the AMT Laboratories Technical Bulletin available at PROSOCO R-GUARD Spray Wrap is packaged in 5-gallon containers. R-GUARD Spray Wrap Exterior Gypsum Board OSB Plywood CMU Coverage Rates sq.ft. per gallon sq.ft. per gallon per coat Prepare all joints, seams, cracks, fastener penetrations and rough openings prior to application of the primary air barrier. See appropriate product data sheets and R-GUARD Installation Guidelines for more information. Application: Exterior Sheathing 1. Apply Spray Wrap to Gypsum, Plywood and OSB sheathing to achieve a continuous, pinhole free coating. Some gypsum sheathing will require additional material due to varying substrate porosity. 2. When spray applying, back roll as necessary to ensure there are no pinholes, voids or gaps in the membrane. 3. Inspect membrane before covering. Repair any punctures or damaged areas by applying additional Spray Wrap. Overlap repairs, penetration treatments, transitions, rigid flashing and other air barrier components to ensure positive drainage and continuity of the air and water-resistive barrier. Application: CMU Wall Construction 1. Apply sufficient Spray Wrap to fill and cover the entire face of the exterior wall assembly. Let dry. 2. Apply a second coat of Spray Wrap to achieve hide. The finished application must be continuous and free of voids and pinholes. If necessary, back roll spray to achieve a void- and pinhole-free surface. Take special care to achieve full coverage around wall ties or surface irregularities. 3. Inspect membrane before covering. Repair any punctures or damaged areas by applying additional Spray Wrap. Overlap repairs, penetration treatments, transitions, rigid flashing and other air barrier components to ensure positive drainage and continuity of the air and water-resistive barrier. Curing and Drying Complete drying times vary with temperature, humidity and surface conditions. Protect from rain or freezing until completely dry. At 70 F (21 C) and 50% relative humidity, R-GUARD Spray Wrap dries to touch and can be over coated in 2-4 hours. Cleanup Clean tools and equipment with water immediately after use. Mechanically remove dried material. BEST PRACTICES PROSOCO R-GUARD Joint & Seam Filler, FastFlash and AirDam are recommended for improved performance of all R-GUARD air- and water-resistive barrier coatings. Though R-GUARD Spray Wrap can be located anywhere in the wall assembly, the ideal location is on the cavity-facing side of the exterior sheathing or CMU backup. This positions the air barrier to accommodate transitions with other building components. It also lets the air barrier perform as a water-resistive barrier. It is not necessary to apply R-GUARD Spray Wrap to the inside of rough openings prepared with FastFlash. Always use two coats of R-GUARD Spray Wrap on CMU walls. Hot Weather Precautions: If air or surface temperatures exceed 95 F (35 C), apply to shaded surfaces and before daytime air and surface temperatures reach their peak. Hot surfaces may be cooled with a mist of fresh water. Surfaces may be damp but must be free of standing water before application. Keep containers closed and out of direct sunlight when not in use. Cover open pails with a wet towel as needed to prevent skinning. Coverage rates will vary depending on surface porosity, moisture uptake, and other factors. Many gypsum sheathing products require additional material to achieve hide and the desired mil thickness for a pinhole free coating. In some cases two coats may be required. Actual rates must be determined through mock-up applications. For more information regarding coverage rates as it pertains to glass-mat sheathing, please consult the AMT Laboratories Technical Bulletin available at Common installation guidelines depicting use of PROSOCO R-GUARD products are available at To schedule field technical support, contact your PROSOCO Technical Customer Care toll-free at Field visits by PROSOCO personnel are for the purpose of making technical recommendations only. PROSOCO is not responsible for providing job site supervision or quality control. Proper application is the responsibility of the applicator. Product Data Sheet Page 3 of 4 Item #70010 RGSW PROSOCO

11 Spray Wrap SAFETY INFORMATION PROSOCO R-GUARD Spray Wrap contains silicon dioxide, titanium dioxide, calcium carbonate. May cause skin irritation with prolonged contact. Use with adequate ventilation, safety equipment and job site controls during application and handling. Read the full label and MSDS for precautionary instructions before use. First Aid Ingestion: Do not induce vomiting. If vomiting occurs, keep victim s head lower than waist to prevent aspiration. Seek medical attention. Eye Contact: Rinse thoroughly for 15 minutes. Get medical assistance if irritation persists. Skin Contact: Remove contaminated clothing and rinse thoroughly. Get medical attention if irritation persists. Launder contaminated clothing before reuse. Inhalation: Remove to fresh air. Get medical attention as necessary. 24-Hour Emergency Information: INFOTRAC at WARRANTY Information and recommendations are based on our research and the research of others, and are believed to be accurate. No guarantee of their accuracy is made because we cannot anticipate every application or variations encountered in masonry surfaces, job conditions and methods used. The purchasers shall make their own tests to determine the suitability of such products for a particular purpose. PROSOCO, Inc. warrants this product to be free from defects. Where permitted by law, PROSOCO makes no other warranties with respect to this product, express or implied, including without limitation the implied warranties of merchantability or fitness for particular purpose. PROSOCO s liability shall be limited in all events to supplying sufficient product to re-treat the specific areas to which defective product has been applied. Acceptance and use of this product absolves PROSOCO from any other liability, from whatever source, including liability for incidental, consequential or resultant damages whether due to breach of warranty, negligence or strict liability. This warranty may not be modified or extended by representatives of PROSOCO, its distributors or dealers. PRODUCT DATA SHEET CUSTOMER CARE Factory personnel are available for product, environmental and job-safety assistance with no obligation. Call and ask for Customer Care - technical support. Factory-trained representatives are established in principal cities throughout the continental United States. Call Customer Care at , or visit our web site at for the name of the PROSOCO R-GUARD representative in your area. Product Data Sheet Page 4 of 4 Item #70010 RGSW PROSOCO

12 PRODUCT TEST RESULTS Spray Wrap ICC-ES AC212 1 Acceptance Criteria for Water-Resistive Coatings Used as Water-Resistive Barriers Over Exterior Sheathing Test Method Criteria Results Tensile Bond ASTM C 297 Minimum 15 psi (105 kpa) Pass Freeze-Thaw ICC-ES AC212 No cracking, checking, crazing, erosion, delamination or other deleterious effects Water Resistance ASTM D 2247 No cracking, checking, crazing, erosion, delamination, or other deleterious effects Pass Pass Water Vapor Transmission ASTM E 96 Wet Cup Measure 10.5 perms Water Penetration ASTM E 331 No visible water penetration at the sheathing joints as viewed from the back of the panel Pass Structural, Racking, Restrained Environmental Conditioning & Water Penetration ASTM E 1233 A ASTM E 72 ICC-ES AC212 ASTM E 331 No cracking of the coating Pass Weathering ICC-ES AC212 AATCC No cracking of the coating; no water penetration Pass Air Permeance ASTM E L / s m 2 at 75 Pa ( cfm / ft 2 at 1.57 psf) Pass: L / s m 2 at 75 Pa ( cfm / ft 2 at 1.57 psf) ABAA: Air Barrier Association of America Acceptance Criteria for Liquid Applied Membranes Test Method Criteria Results Air Permeance ASTM E L / s m 2 at 75 Pa ( cfm / ft 2 at 1.57 psf) Air Leakage of Air Barrier Assemblies ASTM E L / s m 2 at 75 Pa ( 0.04 cfm / ft 2 at 1.57 psf) Water Resistance AATCC No water infiltration after exposure to 55 cm head of water for 5 hours Pass: L / s m 2 at 75 Pa ( cfm / ft 2 at 1.57 psf) Pass: L / s m 2 at 75 Pa (0.003 cfm / ft 2 at 1.57 psf) Pass Fastener Sealability ASTM D 1970 No water infiltration Pass Pull Adhesion ASTM D kpa (16 psi) or substrate failure Pass ICC-ES AC212 Entire Suite of Tests Pass Pass Water Vapor Permeance at applied thickness ASTM E 96 Report in Ng/(Pa s m 2 ) Wet: 600 Ng/(Pa s m 2 ) Fire Testing Test Method Criteria Results Fire Propagation Characteristics of Exterior Non-Load-Bearing Wall Assemblies NFPA Must resist flame propagation and flame spread Pass 4 Determining Ignitability of Exterior Wall Assemblies NFPA Cannot exhibit sustained flaming when exposed to radiant heat flux of 12.5 kw/m 2 ± 5% for 20 minutes Pass Surface Burning Characteristics ASTM E 84 Criteria for ICC and NFPA Class A Building Material: Flame Spread 25 Smoke Developed 450 Meets Class A Building Material: Flame Spread: 15 Smoke Developed: 40 Other Resistance to Mold Growth ASTM D 3273 No mold growth after 28 days Pass NOTES: 1: International Code Council Evaluation Service Acceptance Criteria 212 2: American Association of Textile Chemists and Colorists 3: National Fire Protection Association 4: Sealant Waterproofing & Restoration Institute Project No Product Test Results Page 1 of 1 Item #70010 RGSW PROSOCO

13 amtico technical specifications Style Construction Wear layer thickness Overall thickness Amtico Collection - Stone Luxury Vinyl Tile with bevelled edges 40 mil (1mm) (2.5mm) Sizes (style dependent) 305 x 305mm (12 x 12 ), 305 x 457mm (12 x 18 ), 305 x 610mm (12 x 24 ), 457 x 457mm (18 x 18 ) Other sizes available - refer to brochure matrix for specific product sizes Pieces per carton 45 pcs of 12 x pcs of 12 x pcs of 12 x pcs of 18 x 18 Coverage per carton Specification (ASTM F-1700) Heat stability (ASTM F-1514) Stain & chemical resistance (ASTM F-925) 45 sq. ft. Depends on the size of product Class 3 Type A & B Wear Group Classification (EN 685) 23/34/43 Third Party Certification Rapidly Renewable Resource Content FloorScore Abrasion Resistance (EN 660) Group T Flammability/Smoke Emissions (EN ASTM E648, ASTM E662) N.B.S. smoke chamber test (ASTM-E-662) Slip Resistance (DIN 51130, EN 13893, ASTM C1028) Residual Indentation (EN 433, ASTM F1914) Light Stability (ISO 105-B02, ASTM F1515) Dimensional Stability (EN 434, ASTM F2199) Curl (EN 434) Flexibility (EN 435, ASTM F137) Castor Chair Resistance (EN 425) Electrostatic Performance (EN 1815, ISO 6356) Sound Reduction (DIN 52210, EN ISO 140-8/EN ISO 717-2) Thermal Resistance (EN 12664) Thermal Conductivity (DIN 52612) NF-UPEC Classification (NF189 certificate No ) Static Load Limit (ASTM 970) Resistance to Heat (ASTM 1514) 4% by total product weight Bfl-s1 Class 1, < 450 (non-flaming mode) <450 (non-flaming mode) R9, Class DS, 1.0 (dry coefficient or friction), ADA complaint Residual > 7, < 2kV 4 db m2k/w (underfloor heating suitable) 0.4 to 0.65 W/mK 3.0 to 4.5 BTU/in/ft2/ F U4P3E2C2 (Armstrong PSI): Pass Surface Sealing Emissions (CDPH section 01350, DIBt/AgBB, AFSSET) PUR-Beschichtung manningtoncommercial.com AMTICO_STONE_TECH_SPEC.indd 1 1/21/13 7:18 AM

14 STONE

15 DESIGNED IN ENGLAND AND MADE IN THE USA, THE AMTICO COLLECTION EMBODIES AESTHETIC BEAUTY AND SUPERIOR PERFORMANCE.

16 FRAGMENT Astro AROSFR33, Comet AR0SFR78 and Meteor AROSFR44 COVER: Fossil Limestone AROSFL33

17 WARM DARK Stria Sand AR0SMS47 in Broken Bond Layout

18 NEUTRAL DARK Stria Basalt AR0SMS43, Stria Lava AR0SMS44 and Stria Silt AR0SMS40

19 COOL DARK Graphite Slate AR0SSL23 COOL LIGHT Exposed Concrete AR0SEC30 in Brick Block Layout

20 Product Name Product Code Price Point Surface Finish Available in Cross Grain 12 x 12 (305 x 305mm) 12 x 18 (305 x 457mm) 18 x 18 (457 x 457mm) 12 x 24 (305 x 610mm) Straight Grain 18 x 24 (457 x 610mm) Xtra 18 x 36 (457 x 915mm) Xtra 18 x 48 (457 x 1220mm) Xtra 7.2 x 48 (183 x 1220mm) Xtra 9 x 48 (229 x 1220mm) Xtra 3 x 36 (76 x 915mm) 4.5 x 36 (114 x 915mm) 6 x 36 (152 x 915mm) 9 x 36 (229 x 915mm) Cross Grain 18 (457mm) & 36 (915mm) in length 24 (610mm) & 48 (1220mm) in length Stripping option Amtico Custom Design Signature & Choice Layouts Signature & Choice Borders & Motifs Buckland Stone AR0SST42 S Ceramic Cadence Aeria AR0SPB31 S Ceramic Cadence Atlas AR0SPB42 S Ceramic Cadence Delta AR0SPB32 S Ceramic AMTICO COLLECTION STONE PRODUCT AVAILABILITY Cadence Dune AR0SPB44 S Ceramic Cadence Montis AR0SPB22 S Ceramic Cadence Savannah AR0SPB43 S Ceramic Caspian Limestone AR0SLC74 S Ceramic City Marble AR0SEM33 S Ceramic Composite Calcium AR0SGN11 A Ceramic Composite Flint AR0SGN32 A Ceramic Composite Pumice AR0SGN31 A Ceramic Corinthian Marble** AR0STV13 S Ceramic Crema Marfil AR0SMF47 S Ceramic Cumbrian Slate** AR0SSL32 S Ceramic Doric Marble AR0STV14 S Ceramic Exposed Concrete AR0SEC30 S Ceramic Fossil Limestone AR0SFL33 S Ceramic Fragment Abyss AR0SFR22 A Riven Marble Fragment Astro AR0SFR33 A Riven Marble Fragment Comet AR0SFR78 A Riven Marble Fragment Meteor AR0SFR44 A Riven Marble Fragment Nova AR0SFR11 A Riven Marble Fragment Orion AR0SFR38 A Riven Marble Graphite Slate** AR0SSL23 S Ceramic Honed Limestone Natural AR0SLH11 S Ceramic Jura Beige AR0SJA33 S Ceramic Jura Grey AR0SJA34 S Ceramic Jura Yellow AR0SJA75 S Ceramic Limestone AR0SLK14 S Ceramic Limestone Biscuit AR0SLN14 S Ceramic Limestone Calico AR0SLK36 S Ceramic Lulworth Stone AR0SST41 S Ceramic Mica Mix Bisque AR0SMM42 A Ceramic Mica Mix Earth AR0SMM44 A Ceramic Mica Mix Eggshell AR0SMM41 A Ceramic Mirabelle Bleu AR0SMB34 S Ceramic Mirabelle Creme AR0SMB14 S Ceramic Riverstone Chalk AR0SRS14 S Ceramic Riverstone Mantle AR0SRS44 S Ceramic Riverstone Quarry AR0SRS43 S Ceramic Riverstone Tundra AR0SRS40 S Ceramic Sedimentary Grey Stone AR0SSG31 S Ceramic Slate Noire AR0SSL22 S Riven Marble Stria Ash AR0SMS13 S Ceramic Stria Basalt AR0SMS43 S Ceramic Stria Canyon AR0SMS48 S Ceramic Stria Crater AR0SMS45 S Ceramic Stria Lava AR0SMS44 S Ceramic Stria Mineral AR0SMS15 S Ceramic Stria Rock AR0SMS33 S Ceramic Stria Sand AR0SMS47 S Ceramic Stria Sediment AR0SMS14 S Ceramic Stria Silt AR0SMS40 S Ceramic Stria Volcanic AR0SMS42 S Ceramic Travertine Honey AR0STV32 S Ceramic Travertine Ivory AR0STV31 S Ceramic Travertine Romano** AR0STV33 S Ceramic Upton Stone AR0SST43 S Ceramic Urban Marble** AR0SEM30 S Ceramic Welsh Slate AR0SSL21 S Riven Marble Worn Concrete AR0STL39 S Ceramic Price Point Guide: S - Standard and Standard Xtra, A - Advanced and Advanced Xtra New Products for 2013 ** Cross Grain as standard All products are urethane coated and bevelled as standard

21 AMTICO TECHNICAL SPECIFICATIONS Style Construction Wear layer thickness Overall thickness Amtico Collection - Stone Luxury Vinyl Tile with bevelled edges 40 mil (1mm) (2.5mm) Sizes (style dependent) 305 x 305mm (12 x 12 ), 305 x 457mm (12 x 18 ), 305 x 610mm (12 x 24 ), 457 x 457mm (18 x 18 ) Other sizes available - refer to brochure matrix for specific product sizes Pieces per carton 45 pcs of 12 x pcs of 12 x pcs of 12 x pcs of 18 x 18 Coverage per carton Specification (ASTM F-1700) Heat stability (ASTM F-1514) Stain & chemical resistance (ASTM F-925) 45 sq. ft. Depends on the product and product size Class 3 Type A & B Wear Group Classification (EN 685) 23/34/43 Third Party Certification Rapidly Renewable Resource Content FloorScore Abrasion Resistance (EN 660) Group T Flammability/Smoke Emissions (EN ASTM E648, ASTM E662) N.B.S. smoke chamber test (ASTM-E-662) Slip Resistance (DIN 51130, EN 13893, ASTM C1028) Residual Indentation (EN 433, ASTM F1914) Light Stability (ISO 105-B02, ASTM F1515) Dimensional Stability (EN 434, ASTM F2199) Curl (EN 434) Flexibility (EN 435, ASTM F137) Castor Chair Resistance (EN 425) Electrostatic Performance (EN 1815, ISO 6356) Sound Reduction (DIN 52210, EN ISO 140-8/EN ISO 717-2) Thermal Resistance (EN 12664) Thermal Conductivity (DIN 52612) NF-UPEC Classification (NF189 certificate No ) Static Load Limit (ASTM 970) Resistance to Heat (ASTM 1514) 4% by total product weight Bfl-s1 Class 1, < 450 (non-flaming mode) <450 (non-flaming mode) R9, Class DS, 1.0 (dry coefficient or friction), ADA complaint Residual > 7, < 2kV 4 db m2k/w (underfloor heating suitable) 0.4 to 0.65 W/mK 3.0 to 4.5 BTU/in/ft2/ F U4P3E2C2 (Armstrong PSI): Pass Emissions (CDPH section 01350, DIBt/AgBB, AFSSET) manningtoncommercial.com

22 AMTICO MULTI-PERFORMANCE SYSTEM (MPS) The Amtico Collection s finishes innovatively combine texture, color, and pattern to create a vibrant product ideal for expressing any design vision. Our diverse product collection includes wood, stone, and abstract visuals. The Amtico Collection is extremely durable and highly flexible, allowing for design creativity and proven performance. Our floors are constructed using our world leading Multi-Performance System (MPS), providing the most durable and highest fidelity offering in LVT, backed by our 20 year commercial warranty. URETHANE COATING Our proprietary surface treatment provides exceptional wear resistance to ensure the floor retains its authentic aesthetics for years to come. Added slip, scuff, stain resistance, in addition to lower maintenance, translates to an overall lower total cost of ownership. PERFORMANCE WEAR LAYER 1 Ceramic infused for improved slip resistance and durability. (R9 rating) PERFORMANCE WEAR LAYER 2 High-density layer. Engineered to withstand indentations and protect against everyday wear and tear. AESTHETIC LAYER Our in-house design team creates aesthetic visuals with remarkable realism and clarity, by utilizing the latest technology in imaging, texturing, and finishing. BACKING LAYERS The final supporting layers provide a foundation for the aesthetic layers, to guarantee high performance for years to come. Amtico LVT contains rapidly renewable and pre-consumer recycled content, and is 100% recyclable.

23 technical services Amtico Installation Guidelines General The installation of Amtico is straightforward and similar to the installation procedures that apply to all quality resilient tile floors. Good preparation is essential for a trouble-free installation. Do not install Amtico until jobsite testing and subfloor preparations are finished and the work of all other trades is complete. Site conditions must comply with the relevant building codes and local, state and national regulations. Documentation of Moisture and ph test results is required when processing claims. For guidance about subfloor testing and Amtico installation recommendations. Contact Mannington Technical Services at Amtico is recommended for use over properly prepared concrete, suspended wood, metal and other suitable substrates. Amtico can be used with radiant heating systems (maximum subfloor surface temperature of 81 F). Amtico is not suitable for external installation or unheated locations. Amtico tiles, adhesive, jobsite and subfloor must be acclimated to a stable condition before installation. Following installation, Amtico should be protected from traffic for 24 hours, point loads and rolling traffic for 48 hours and should not be washed for 5 days. The flooring should remain at a temperature between F (13-27 C) during its service life. Always follow other manufacturers written recommendations when using their proprietary materials for subfloor preparation. A. Material Receiving, Handling & Storage 1. Immediately remove any shrink wrapping and verify materials delivered are correct style, color and quantity. 2. Report discrepancies immediately to Technical Services at Labor claims for installation of products installed with visual defects or incorrect style will not be honored. 3. Store all materials off the floor (keep cartons flat) in a weather-tight enclosure between F (13-27 C). 4. Acclimate tile, adhesive and jobsite to a stable condition between F (18-27 C) and 50% +/- 10% RH for 48 hours before, during and after installation. Acclimate all materials onsite and off stack tile cartons to a single layer keeping cartons flat. Temporary heating and cooling should be used if permanent HVAC is not operational. 5. Tiles should not be stored close to exterior walls, in direct sunlight or near HVAC vents. B. Jobsite Testing 1. Before jobsite testing, the building envelope must be sealed (walls, roofing, windows, doorways etc., installed). 2. Anticipated environmental conditions must be maintained or 75 F +/- 10 F (24 C +/- 6 C) and 50% +/- 10% RH a minimum of 48 hours before and during testing (ASTM F 710). 3. Test sites must be properly prepared and protected for the duration of testing to achieve valid results. 4. Surface Flatness for all Subfloors: The surface shall be flat to 1/8 in 10 ft (3 mm in 3 m). To check flatness, place a 10 ft straight edge on the surface and measure the gap or use another suitable method. 5. Concrete Subfloors: a. Concrete subfloors must be finished and cured without additives, curing compounds, hardeners or surface treatments that may prevent proper bonding of the flooring materials (ACI and ASTM F710). b. Randomly check concrete subfloor for porosity using the drop water test. Place a 1 inch diameter drop of water directly onto the concrete subfloor. If the water droplet does not dissipate within 60 to 90 seconds the subfloor is considered non-porous. c. Concrete subfloors must have a minimum compressive strength of 3000 psi. d. Concrete subfloors shall not consist of lightweight concrete or gypsum with less than 100 lbs. /cubic foot density. e. Moisture Testing: Perform either the preferred In-situ Relative Humidity (RH) Test (ASTM F2170) or the acceptable Moisture Vapor Emission Rate (MVER) Test (ASTM F1869). Internal RH readings above 80% or MVER readings above 5 lb/1000 SF/24 hours require a moisture suppressant system. f. Alkalinity: Must test surface alkalinity (ASTM F710). A 7.0 to 10.0 ph is acceptable. Reduce higher ph by mopping on a vinegar/water solution: 1 pint vinegar to 2 gallons water. 6. Wood Subfloors and underlayment panels shall have the moisture content tested using a suitable wood pin meter. Readings between the wood subfloor and underlayment panels should be within 3% and have a maximum moisture content of 14% or less. Effective moisture control in basements and crawlspaces is essential for achieving a successful long term installation. C. Moisture Suppressant System Concrete subfloors that exceed 80% RH or 5 lbs MVER require a Moisture Suppressant System. Due to complexities associated with moisture vapor transmission, emissions and movement of soluble salts (alkalinity) in concrete subfloors, we do not offer, recommend or warranty a specific solution for excess moisture in concrete slabs. However, there are many companies that offer solutions with warranties for excess moisture in concrete slabs. Choices that Work manningtoncommercial.com