Reference: FT MOPOLY-es Date: 27/10/14 Revision: 2 Page: 1 of 9

Transcription

1 Denomination: POLYESTER CHEMICAL MORTAR Codes: MOPOLY, MOPOLYP, MOPOLYW Reference: FT MOPOLY-es Date: 27/10/14 Revision: 2 Page: 1 of 9 CHARACTERISTICS Easy assembly. For use in non-cracked concrete, hollow and solid partitioning. For use with medium-heavy loads. For use with static or quasi-static loads. Versions in bichromated steel, stainless steel A2 and A4. Polyester resin for all types of materials. Range of temperatures for use: -40ºC to +80ºC (long term maximum temperature +50ºC). APPLICATIONS For fixing stone cladding. Rehabilitation of façades. For fixing notices, air conditioning supports, boilers, awnings, signs, balconies, shelving units, railings, etc. View Web profile: BASE MATERIAL RECOMMENDED TENSION RESISTANCES VALID FOR MEASUREMENTS M8 - M24 DRILL HOLE CONDITION APPLICATION EXAMPLES

2 Denomination: POLYESTER CHEMICAL MORTAR Codes: MOPOLY, MOPOLYP, MOPOLYW Reference: FT MOPOLY-es Date: 27/10/14 Revision: 2 Page: 2 of 9 1. RANGE ITEM CODE MEAS. PHOTO COMPONENT MATERIAL 1 MOPOLY170 MOPOLY300 MOPOLY ml. 300 ml. 410 ml. POLYESTER MORTAR Polyester resin with styrene. Presentation: 170, 300 and 410 ml cartridges MOPOLYP300 MOPOLYP ml. 410 ml. POLYESTER MORTAR STONE COLOUR Polyester resin with styrene in stone colour. Presentation: 300 and 410 ml cartridges MOPOLYW300 MOPOLYW ml. 410 ml. POLYESTER MORTAR WINTER Polyester resin with styrene. Low temperature applications. Presentation: 410 ml cartridges ACCESSORIES ITEM CODE PHOTO COMPONENT MATERIAL MOPISSI Gun for standard 170 and 300 ml cartridges. 1 MOPISTO APPLICATION GUNS Gun for 410 ml coaxial cartridges MOPISPR Professional gun for 410 ml coaxial cartridges Dieses Produkt wird nicht in Deutschland 2 MO-ES EQ-AC EQ-A2 EQ-A4 STUDS Threaded steel studs, class 5.8 ISO Threaded steel studs, class 5.8 ISO Threaded Stainless steel studs A2-70 Threaded Stainless steel studs A MORCEPKIT CLEANING BRUSHES Kit of 3 cleaning brushes of ø14, ø20 and ø29 mm. 4 MOBOMBA CLEANING PUMP Pump for cleaning dust and drill hole fragments 5 MORCANU MIXING NOZZLE Plastic. Helix static mixer 6 MO-TN NYLON SLEEVE Plastic. Available in white or grey 7 MO-TR METAL THREADED SLEEVE Metal threaded sleeve M8, M10, M12, zinc plated. 8 MO-TM METAL SLEEVE Metal sleeve Ø12, Ø16 and Ø22

3 Denomination: POLYESTER CHEMICAL MORTAR Codes: MOPOLY, MOPOLYP, MOPOLYW Reference: FT MOPOLY-es Date: 27/10/14 Revision: 2 Page: 3 of 9 3. INSTALLATION DATA 3.1. CONCRETE FIXINGS MEASUREMENT M8 M10 M12 M16 M20 M24 d 0 : nominal diameter [mm] d f : fixture hole diameter [mm] T ins : torque [Nm] Circular cleaning brush diameter Ø14 Ø20 Ø29 h ef,min = 8d h 1 : drill hole depth [mm] s cr,n : critical spacing [mm] c cr,n : critical edge distance [mm] c min : minimum distance to edge [mm] : minimum spacing [mm] h min : minimum concrete thickness [mm] Standard Stud h 1 : drill hole depth [mm] s cr,n : critical spacing [mm] c cr,n : critical edge distance [mm] c min : minimum distance to edge [mm] : minimum spacing [mm] h min : minimum concrete thickness [mm] h ef,max = 12d h 1 : drill hole depth [mm] s cr,n : critical spacing [mm] c cr,n : critical edge distance [mm] c min : minimum distance to edge [mm] : minimum spacing [mm] h min : minimum concrete thickness [mm] Bichromated Stud Code EQAC08110 EQAC10130 EQAC12160 EQAC16190 EQAC20260 EQAC24300 Stainless Steel Stud Code A2 / A4 EQA EQA EQA EQA EQA EQA EQA EQA EQA EQA EQA EQA The h ef depth value may be selected by the user ranging between h ef,min = 8d and h ef,max = 12d. Any intermediate values may be interpolated. Critical distances are those where anchors in a group of anchors are not influenced by one another with regard to tension load effects. For smaller distances, down to minimum distances, corresponding reduction coefficients must be applied. Standard studs are available for each measurement, as shown in the table.

4 Reference: FT MOPOLY-es Date: 27/10/14 Revision: 2 Page: 4 of SOLID OR HOLLOW BRICK FIXINGS TYPES OF BRICKS Brick nº 1 Hollow baked clay brick HLz 12-1, 0-2DF according to EN mm / 112 mm / 115 mm f b 12 N/mm 2 / ρ 1,0 kg/dm 3 Brick nº 2a Hollow sillico calcareous brick KSL 12-1, 4-3DF according to EN mm / 175 mm / 113 mm f b 12 N/mm 2 / ρ 1,4 kg/dm 3 Brick nº 2b Hollow sillico calcareous brick KSL 12-1, 4-2DF according to EN Brick nº mm / 240 mm / 237 mm f b 12 N/mm 2 / ρ 1,4 kg/dm 3 Brick nº 3 Solid baked clay brick Mz 12-2, 0-NF according to EN Length / width / height: 240 mm / 116 mm / 71 mm f b 12 N/mm 2 / ρ 2,0 kg/dm Solid sillico calcareous brick KS 12-2, 0-NF according to EN mm / 115 mm / 70 mm f b 12 N/mm 2 / ρ 2,0 kg/dm Brick nº 5 Hollow baked clay brick HLzW 6-0,7-8DF according to EN mm / 240 mm / 240 mm f b 6 N/mm 2 / ρ 0,8 kg/dm 3 Brick nº 6 Hollow lightweight concrete block Hbl 2-0,45-10DF according to EN mm / 300 mm / 248 mm f b 2,0 N/mm 2 / ρ 0,45 kg/dm 3 Brick nº 7 Hollow lightweight concrete block Hbl 4-0, 7-8DF according to EN mm / 240 mm / 248 mm f b 4,0 N/mm 2 / ρ 0,7 kg/dm 3 Brick nº 8 Concrete block Hbn 4-12DF according to EN mm / 240 mm / 238 mm f b 4 N/mm 2 / ρ 1,2 kg/dm 3

5 Reference: FT MOPOLY-es Date: 27/10/14 Revision: 2 Page: 5 of INSTALLATION PARAMETERS For fixings in hollow bricks, a nylon or metal sleeve should be used to keep the resin in place and to prevent it from seeping through interior holes. MEASUREMENT M8 M10 M12 Nylon Sleeve ls d Mortar volume per sleeve [ml] h 1 : drill hole depth [mm] h nom : sleeve installation depth [mm] h ef : stud bolt depth [mm] t fix : thickness of material to be fixed [mm] h c : base material thickness [mm] d f : metal sheet diameter [mm] T ins : torque [Nm] Circular brush ø20 Stud Code MOES08110 MOES10115 MOES12110 Sleeve Code MOTN15085 MOTN15085 MOTN20085 Critical/Minimum spacing and distance to edge c min s cr c min s cr c min s cr Brick number 1 [mm] Brick number 2 [mm] Brick number 3 [mm] Brick number 4 [mm] Brick number 5 [mm] Brick number 6 [mm] Brick number 7 [mm] Brick number 8 [mm] In some cases to perform installations in bricks where a stud is required to be threaded, a metal sleeve with an internal thread can be used for fixing. In this case, the metal sleeve with internal thread must be inside a plastic sleeve. The parameters are indicated in the following table: MEASUREMENT M8 M10 M12 Metal internal threaded sleeve 12x80 14x80 16x80 Plastic sleeve ls d Mortar volume per sleeve [ml] h 1 : drill hole depth [mm] h nom : sleeve installation depth [mm] h ef : stud bolt depth [mm] t fix : thickness of material to be fixed [mm] h c : base material thickness [mm] d w : metal sheet diameter [mm] T ins : torque [Nm] Circular brush ø20 Stud code MOES08110 MOES10115 MOES12110 Sleeve Code MOTN15085 MOTN15085 MOTN20085 Metal Internal Threaded Sleeve code MOTRO08 MOTRO10 MOTRO12 Critical/Minimum spacing and distance to s s edge c cr min c cr min c min s cr Brick number 1 [mm] Brick number 2 [mm] Brick number 3 [mm] Brick number 4 [mm] Brick number 5 [mm] Brick number 6 [mm] Brick number 7 [mm] Brick number 8 [mm]

6 Reference: FT MOPOLY-es Date: 27/10/14 Revision: 2 Page: 6 of 9 4. PRODUCT INSTALLATION PROCEDURE 4.1. INSTALLATION IN CONCRETE 1. DRILLING Check the concrete base is compact and porosity is insignificant. Suitable for wet, dry or flooded drill holes. Cartridge installation temperature: 5 ºC. Base material installation temperature: MOPOLY, MOPOLYP 5 ºC MOPOLYW -5 ºC Use drill in hammer mode. Drill to the specified diameter and depth values BLOW AND CLEAN Clear the drill holes completely of dust and fragments by following the procedure shown in the picture. If the drill hole is flooded, the water must be removed before mortar is injected. A B* C. OPEN CARTRIDGE Screw the nozzle into the cartridge and place the assembly in the application gun. Squeeze on the trigger repeatedly until the mortar comes out of the nozzle in a uniform grey colour. Any iridescence indicates improper mixing. Always discard the first two doses of each cartridge: these are never to be used for fixing. *For 170 and 300 ml cartridges, cut end of bag, behind seal clip. 7. INJECT MORTAR Insert the nozzle to the bottom of the drill hole and apply mortar: gradually remove the nozzle, ensuring there are no air bubbles. Fill the hole to ½ and ¾ of its depth. In the event of not fully using the cartridge, leave nozzle attached. Only change if using again and handling time has expired, remembering to discard the first two doses of mortar. 8. INSTALLATION Introduce the stud to be installed by screwing it lightly down to the installation depth value manually; ensuring the mortar covers the stud thread. The introduction of the anchor must take place within the handling time. The mortar must seep from the top of the drill hole to ensure it is completely full and there are no gaps between the stud and the drill hole. TYPE BASE MATERIAL TEMPERATURE [ºC] HANDLING TIME [min] CURING TIME [min] MOPOLY / MOPOLYP MOPOLYW min to to to to to to min to to to to APPLY TORQUE Once the curing time has elapsed, apply torque, never exceeding the values indicated in the table in section 3.1.

7 Reference: FT MOPOLY-es Date: 27/10/14 Revision: 2 Page: 7 of INSTALLATION IN BRICKS 1. DRILLING Check the concrete base is compact and porosity is insignificant. Suitable for wet, dry or flooded drill holes. Cartridge installation temperature: 5 ºC. Base material installation temperature: MOPOLY, MOPOLYP 5 ºC MOPOLYW -5 ºC Use drill in rotation mode. Drill to the specified diameter and depth values BLOW AND CLEAN Clear the drill holes completely of dust and fragments by following the procedure shown in the picture. If the drill hole is flooded, the water must be removed before mortar is injected 4. POSITION SLEEVE(s) Insert the metal or plastic sleeve into the drill hole so it is level with the surface of the base material. Remove any plaster, mortar, etc, so that the sleeve border is level with the brick surface. A B* C. OPEN CARTRIDGE Screw the nozzle into the cartridge and place the assembly in the application gun. Squeeze on the trigger repeatedly until the mortar comes out of the nozzle in a uniform grey colour. Any iridescence indicates improper mixing. Always discard the first two doses of each cartridge: these are never to be used for fixing. *For 170 and 300 ml cartridges, cut end of bag, behind seal clip. 5. INJECT MORTAR Insert the nozzle to the bottom of the drill hole and apply mortar: gradually remove the nozzle, ensuring there are no air bubbles. Fill the hole to ½ and ¾ of its depth. In the event of not fully using the cartridge, leave nozzle attached. Only change if using again and handling time has expired, remembering to discard the first two doses of mortar. 6. INSTALLATION Introduce the stud to be installed by screwing it lightly down to the installation depth value manually; ensuring the mortar covers the stud thread. The introduction of the anchor must take place within the handling time. The mortar must seep from the top of the drill hole to ensure it is completely full and there are no gaps between the stud and the drill hole. TYPE BASE MATERIAL TEMPERATURE [ºC] HANDLING TIME [min] CURING TIME [min] MOPOLY / MOPOLYP MOPOLYW min to to to to to to min to to to to APPLY TORQUE Once the curing time has elapsed, apply torque, never exceeding the values indicated in the table in section

8 Denomination: POLYESTER CHEMICAL MORTAR Codes: MOPOLY, MOPOLYP, MOPOLYW Reference: FT MOPOLY-es Date: 27/10/14 Revision: 2 Page: 8 of 9 5. STORAGE CONDITIONS Keep the product stored in a cool, dry place, away from direct sunlight and heat sources, at an average temperature between +5 ºC and +25 ºC. Shelf life of unopened cartridge: 18 months from the date of manufacture. The expiration date is indicated on the cartridge. 6. RESISTANCES 6.1. CONCRETE FIXINGS Characteristic resistances for C20/25 concrete for an isolated anchor (without considering anchor-to-anchor or anchor-to-edge distance effects) and class 5.8 studs are shown in the table below: DIAMETER M8 M10 M12 M16 M20 M24 Bichromated Stainless Steel h ef,min = 8d N Rk [kn] 15,2 22,6 30,8 51,5 75,4 101,3 Tension Standard stud N Rk [kn] 19,1 25,4 35,2 51,5 80,1 110,8 h ef,max = 12d N Rk [kn] 18 33,9 46,1 77,2 113,1 152,0 Specific Value τ Rk [N/mm 2 ] 9, ,5 7 Shear All depths V Rk [kn] h ef,min = 8d N Rk [kn] 15,2 22,6 30,8 51,5 75,4 101,3 Tension Standard stud N Rk [kn] 19,1 25,4 35,2 51,5 80,1 110,8 h ef,max = 12d N Rk [kn] 22,9 33,9 46,1 77,2 113,1 152,0 Specific Value τ Rk [N/mm 2 ] 9, ,5 7 Shear All depths V Rk [KN] KN 100 kg For tension resistance values for intermediate depths, apply the following formula: N Rk = τ Rk π d h ef The values underlined and in italics indicate steel failure. The other values indicate pull-out failure. These are coefficients for tension loads in high-resistance concrete types: Recommended Safety Values C30/37 C40/50 C50/60 1,12 1,19 1,30 SAFTEY COEFFICIENTS RESISTANCE REDUCTION COEFFICIENT Pull-out Failure Steel Failure SAFETY COEFFICIENT FOR LOADS Bichromated Stainless Tension 1,80 1,50 Shear -- 1,25 Tension 1,80 -- Shear -- 1,56 1,40

9 Reference: FT MOPOLY-es Date: 27/10/14 Revision: 2 Page: 9 of BRICK FIXINGS Base Material* *Consult brick type on Page 4 or Section Threaded Studs Tension and Shear [kn] Metal threaded sleeve Tension and Shear [kn] M8 M10 M12 M8 M10 M12 Brick number 1 2,5 2,0 2,0 1,5 2,5 2,5 Brick number 2 0,75 1,2 1,5 -- 0,75 0,4 Brick number 3 1,5 1,5 3,0 2,0 3,0 4,0 Brick number 4 0,75 0,9 1,5 2,0 1,5 0,9 Brick number 5 1,2 1,2 0,9 0,9 1,5 0,6 Brick number 6 0,6 0,2 -- 0,5 0,3 0,75 Brick number 7 0,6 1,5 1,2 -- 0,4 0,6 Brick number 8 2,5 1,5 2,5 0,6 1,2 0,9 Safety Coefficient OFFICIAL DOCUMENTATION INDEX Fixing Systems have made the following technical documents available through our official website: MOPOLY-es Safety Data Sheet. European Technical Approval ETE 13/0752 for installation in non-cracked concrete according to ETAG 001 Guide, option 7, for M8 to M24. Classified A+ according to French Regulation DEVL A relative to the emission of volatile pollutants for indoor use. LEED MOPOLY Certification of emission of volatile pollutants. EC Certification 1020-CPD Declaration of Performance DoP MOPOLY-en. INDEXCal Anchor Calculation Software. INDEXSOFT MOR Cartridge Calculation Needs Software.