Anchoring threaded rod, bolts, rebar dowels and smooth dowels into concrete, grout filled block and unreinforced masonry

Transcription

1

2

3 ANCHORING & DOWELING Ultrabond 1 Ultrabond 1 Epoxy Anchoring Gel is a two component (1:1 ratio), high modulus, structural epoxy gel. It is a solvent free, no odor, high strength, moisture insensitive, non-sag epoxy system. Anchoring threaded rod, bolts, rebar dowels and smooth dowels into concrete, grout filled block and unreinforced masonry Seismic anchoring and bracing Exceptional strength Long working time (20 minutes at 75 F) Easy to use & can be used with any standard caulking gun Load time in as little as 4 hrs for applications Gel Time 14 minutes 4 hours Temperature Range 35 F 115 F Ultrabond 2 Ultrabond 2 Epoxy Anchoring Gel is a two component (1:1 ratio), 100% solids, high modulus epoxy gel. It is a solvent free, high strength, moisture insensitive, non-sag epoxy system. Ultrabond 2 Epoxy Anchoring Gel is formulated for anchoring threaded rod, bolts, rebar and smooth dowels into concrete, grout filled block, and unreinforced masonry. Ultrabond 2 has been tested in accordance with AC58 and is acceptable for long term tensile loads. It may also be used for short term tensile load anchors, which includes wind and seismic forces. Seismic anchoring and bracing High strength epoxy system Non-Sag formula Easy to use (1:1 ratio) system Long working time Great for setting anchors in elevated temperature environments Concrete Gel Time 75 F) 15 minutes Load Time 10 hours Temperature Range 40 F 110 F with Deep Embedment Anchors D.O.T. Doweling Runway Doweling Rail Anchoring Ultrabond 365 Low Temperature Cure Acrylic Adhesive Ultrabond 365 is a two-component, (10:1 ratio), methyl methacrylate adhesive. It is a high strength, moisture insensitive, non-sag paste adhesive system. Ultrabond 365 Acrylic Adhesive is a low temperature cure product that is formulated for anchoring threaded rods, bolts, and fasteners into concrete, grout filled block, hollow block, and unreinforced masonry as well as anchoring rebar dowels and Ultrabond 1300 Ultrabond 1300 Epoxy Anchoring Gel is a two-component (1:1 ratio), 100% solids, high modulus, structural, epoxy gel. It is a solvent free, no odor, high strength, moisture insensitive, non-sag epoxy system. smooth dowels into pavement/concrete. Ultrabond 365 has been tested in accordance with AC-58 for creep, seismic, freeze-thaw, in-service temperature and damp/wet-hole applications. Anchoring/Fastening into solid-base materials: Stadium seating, Pallet racking & Airport runway/taxi-way expansion Anchoring/Fastening into hollow-base materials with screen) and can be used in damp holes Non- sag adhesive. Fastening in grout filled block and unreinforced masonry Anchoring and bracing for short term tensile load where dynamic, vibratory, wind or intermittent loads exist Doweling applications for rebar and tie bars for full depth concrete Bulk dispensing flowability for efficient application High strength Non-sag epoxy system Easy to use (1:1 ratio) system Exceptional strength Extended temperature range allows for setting of anchors in extreme environments for both elevated and low temperature applications Working Time (75 F) 6 min min. Temperature Range 0 F 100 F Gel Time 75 F) 14 min. 2 hrs. Temperature Range 35 F 110 F

4 Ultrabond 2300 Ultrabond 2300 is a two-component, 100% solids, high strength epoxy bonding adhesive. It is a solvent free, high modulus, moisture insensitive, non-sag epoxy system. Ultrabond 2300 is ideal for use in temperatures ranging from 60 F F. Acceptable uses for the Ultrabond 2300 include rebar dowel and anchor installations where dynamic, vibratory or intermittent loads exist. Ultrabond 2300 can also be used for bonding fresh/plastic concrete to hardened concrete and other substrates or projects that require a nonsag epoxy with a long working time. Bonding fresh concrete to hardened concrete Bonding hardened concrete to hardened concrete Anchoring threaded rod fasteners and rebar dowels Mortar Repair Material (when mixed with dry silica sand) High Strength Epoxy Adhesive Non-Sag Epoxy System Easy to Use (1:1 ratio) Moisture Insensitive Epoxy Concrete Gel Time (75 F) 32 minutes 10 hours Temperature Range 60 F 110 F Ultrabond SpeedSet2 Doweling Adhesive Ultrabond SpeedSet2 Doweling Adhesive is a twocomponent, (10:1 ratio), polyester blend adhesive. It is a solvent free, high modulus, high strength, non-sag adhesive system Ultrabond SpeedSet2 can be applied at temperatures ranging from 25 F to 120 F. Rebar dowel installations where dynamic, vibratory or intermittent loads exist Vertical, horizontal and screen applications Use in concrete, hollow block, brick, clay and stone Exceptional strength allowing usage in damp environments Minimum loading time of 1 hour at 78 F, which is great for applications that require minimum down times Concrete Gel Time (60g 75 F) 7 minutes 60 minutes Temperature Range 25 F 120 F Ultrabond RT66 Rebar and Doweling Adhesive Ultrabond RT66 is a new 2-component Hybrid Ester-Blend formula designed for doweling applications in both cold and elevated temperatures, 25 F to 120 F. It is a high strength, high modulus and moisture insensitive adhesive for installations in damp environments. Ultrabond HS200 Doweling Adhesive Ultrabond HS200 Epoxy Anchoring Gel is a two component (2:1 ratio), 100% solids, high modulus, structural epoxy gel. It is a solvent free, no odor, high strength, moisture insensitive, non-sag epoxy system. HS-200 has been tested in accordance with ICC - AC58 and is acceptable for long term sustained loads as well as short term loading. Anchoring threaded rod and rebar doweling where dynamic, vibratory or intermittent loads exist Perfect for horizontal, vertical and screen applications May be used in concrete, brick, stone, clay and hollow block Rebar dowel installations where dynamic, vibratory or intermittent loads exist High strength, non-sag structural Hybrid Ester blend system Minimum down time with a very fast cure time for installations in damp holes 100% solvent free system means low VOC content Seismic anchoring and bracing for long term sustained loads in accordance to ICC AC-58 Tested for long term creep at elevated temperatures, static loads, seismic / wind loading. Freeze-thaw conditions, damp holes A solvent free system means low VOC content High Strength Color Concrete Gel Time 75 F) 10 minutes 4 hours Temperature Range 35 F 110 F Medium Gel Time (60g 75 F) 8 min. 1 hr. Temperature Range 25 F 120 F Used for the seismic retrofit of the Golden Gate Bridge. Ultrabond 4CC Rebar and Doweling Adhesive Ultrabond 4CC is a high performance epoxy adhesive for anchoring and doweling applications in both cracked and uncracked concrete. It s TESTED IN ACCORDANCE TO ICC-ES AC-308 and Meets 2009 IBC requirements. Refer to ICC-ES ESR-3218 Evaluation Report. Anchoring threaded rods, bolts and fasteners into grout filled masonry, solid brick or either cracked or uncracked concrete Anchoring rebar dowels and smooth dowels into pavement/concrete Suitable for long term sustained loads and seismic bracing Can be used dry, water-saturated or water-filled and submerged applications with no load reductions Airport runways and taxi-way expansions, stadium seating, pallet racking Concrete traffic barriers to concrete bridge decks Non-sag epoxy gel anchoring High strength Color Working Time (70 F) 15 minutes Cure Time 24 hours Temperature Range 70 F 110 F

5 BONDING & COATING Healer/Sealers, Injection Repairs, Grouting & Patching for applications Miracle Bond 1350 Multi-Purpose Repair Epoxy Miracle Bond 1350 is a two-component, high strength, high modulus, moisture insensitive, non-sag, ceramic blend epoxy system. It s ideal for use as a bonding agent for almost any material, including metal, concrete, brick, wood, stone, block and other substrates. Color Concrete Non-Sag Gel Gel Time (75 F) 8 minutes Cure Time 2 75 F Temperature Range 40 F 100 F Crackbond JF311 Polyurea Joint Filler Crackbond JF-311 is a 2-component, rapid curing, elastomeric, polyurea joint filler. It is designed for heavy duty traffic and freezer applications. Joint filler for control joints or new construction saw joints Specifically formulated for industrial floor applications receiving heavy-duty vehicle traffic. Crackbond LR-321 Low Epoxy Crackbond LR-321 is formulated for use as an injection resin for cracks in structural concrete, masonry & wood. It s also perfect for an epoxy grout, healer/sealer or as a mortar when mixed with sand. It has the viscosity of light oil and low surface tension, allowing it to deeply penetrate fine cracks. It cures to a solid with no shrinkage, bonds to both surfaces of the crack, bonding the structure back to its original monolithic strength. Repairing holes and spalls in concrete Repairing rotted wood Bonding fresh concrete to hardened concrete Bonding hardened concrete to hardened concrete Capping paste sealer around ports and cracks for crack injection process Non-sag patching material for cracks and small spalls Bonds to a multitude of substrates Non-sag, high strength epoxy makes it great for overhead and vertical repair Easy to use (1:1 ratio) system 100% solvent free system means low VOC content system-can be used on damp surface Self leveling 100% solids Flexible system that provides 10-15% movement of installed joint width Can be used at temperatures between -40 F F Rapid cure allows repaired joints to be opened to traffic within 90 minutes (at 72 F) Concrete of Resin 77 F Gel Time (72 ) 3 minutes Cure Time (72 ) 90 minutes Temperature Range -40 F 120 F Pressure injection of fine to medium size cracks (3mm to ¼ ) Primer for industrial coatings Bonding agent for new to old concrete repair Resin binder for epoxy mortar patching using addition of aggregate Sealer for interior slabs and exterior above-ground slabs from water, chlorides and mild chemical attack Gravity feed structural crack repair in horizontal concrete, masonry and wood in fine to medium size cracks High strength system-can be used on damp surfaces 100% solvent free system means zero VOC content Low epoxy system ideal for gravity feed crack injection applications for applications for applications For LR-321 Amber When Mixed cps Gel Time (ASTM 60g mass) 20 minutes Initial Cure Time (30 mil thin film) 6 hrs. and 30 min. Temperature Range 40 F 100 F Also Available Crackbond LR-321G Low Thixotropic Formula This unique formula will flow as a liquid when being pumped with a dispensing tool but will cease flowing within (or out) of the crack when pumping stops. This characteristic makes it perfect for blind side crack repairs. Visit our website for all the complete technical data. Crack-Kit Crack Injection and Concrete Repair Kit Our new and improved patented T-Port System with observation windows is everything you need to perform crack injection and concrete repair to multiple applications. KEY CRACK-KIT ADVANTAGES Latex Storage Pod delivers constant injection pressure and indicates if more injection is required Flexible T-Port absorbs disturbances during installation helping to eliminate reattaching ports Leak free direct port/nozzle connection keeps epoxy resin in while allowing air and water to escape Observation windows allows installer to view and confirm the flow of resin within the injected crack KEY USES Crack injection Concrete crack and spall repair Bonding concrete to concrete Patching Material Primer for industrial coatings Healer Sealer Epoxy Grouting Gravity fed structural crack repair Mortar when mixed with sand Capping paste sealer Fix Cracks Rotted Wood Loose Railing Broken Steps Broken Concrete

6 Crackbond SLV-302 Super Low Epoxy Resin Crackbond SLV-302 is formulated for use as an injection resin for cracks in concrete/wood structures and as a penetrating healer/sealer/primer. It has the viscosity of a very light oil, and low surface tension, allowing it to deeply penetrate fine/hairline cracks. It cures to a solid with no shrinkage, bonds to both surfaces of the crack, bonding the structure back to its original monolithic strength. Pressure injection of hairline to fine cracks Primer for industrial coatings Gravity feed structural crack repair in horizontal concrete, masonry and wood in fine cracks Epoxy resin binder for epoxy mortar patching and overlay of interior surface using addition of aggregate Sealer for interior slabs and exterior above-ground slabs, decks, patios, driveways, parking garages and other structures from water, chlorides and mild chemical attack Shear fracture repairs on interior/exterior concrete slabs Bonding agent for new to hardened or hardened to hardened concrete Crackbond SLV-302 is a moisture insensitive product and can be used in damp environments Super low viscosity and low surface tension allows it to deeply penetrate hairline to fine cracks Cures to a solid with no shrinkage and bonds to all surfaces of the crack bonding the structure back to its original monolithic strength 100% solids, solvent free system with zero VOC content. Amber 190 cps Gel Time (ASTM 60g mass at 75 F) 10 minutes Initial Cure Time (30 mil thin film) 7 hours Temperature Range 50 F 100 F Ultrabond 2100, Crackbond LR321 LPL, Ultrabond 2100 LPL Epoxy Bonding/Coating Adhesives - Extended tack free time PRODUCT DESCRIPTION The three featured products in this section are all two component, solvent free, high strength, moisture insensitive self leveling epoxies. The main differences between the products can be found in their color, mixing ratios, viscosity, cure and tack free times. Bonding fresh concrete to hardened concrete Bonding hardened concrete to hardened concrete Mortar repair material (when mixed with dry silica sand) Gravity feed crack repairs Deep hole anchoring Ultrabond 2100 Crackbond LR321 LPL Ultrabond 2100 LPL Mixed (cps) 3, ,000 Gel time (60 gm sample at 75 F) min Tack Free Time 30 mil thin film 3 hrs, 40 min 8-10 hrs 5 hrs, 15 min. Tensile Strength psi 7 days-astm D638 7,210 8,000 3,511 Heat Deflection Temperature F ASTM D Compressive Strength-psi 7 days ASTM D695 10,100 10,800 9,146 Bond Strength-psi 14 day ASTM C882 1,690 3,300 2,600 Mixing Ratio 1:1 2:1 1:1 Color Amber ASTM C881, Type I, II, IV & V, Grade 2, Class B & C X ASTM C881, Type I, II, IV & V, Grade 1, Class B & C X ASTM C881, Type I, II & V, Grade 2, Class C X Crackbond CSR Rapid Cure Polyurethane Crack/Spall Repair Crackbond CSR is a specially formulated very low viscosity two-part hybrid polyurethane rapid cure concrete repair material. Repair spalls & cracks in high traffic areas Repair floors prior to floor grinding/polishing Rebuild spalled floor joints and concrete edges Repair concrete on bridge & parking decks Repair of interior and exterior hairline cracks Penetrating super low viscosity provides high bond strength Reaches 4,900 psi in 1 hour Use in temperatures down to 0 F Cures in 20 minutes Self-leveling Provides excellent results when polished Add aggregate for use as mortar for applications Black, then light gray 60cps mixed Gel Time (75 F) 2.5 minutes Cure Time 20 minutes Temperature Range 0 F 115 F Crackbond FE-2315 Flexible Pick-Proof Epoxy Crackbond FE-2315 is a pick-proof, two component (1:1 ratio), semi-flexible, epoxy adhesive. It is a solvent-free, no odor, moisture insensitive, non-sag epoxy adhesive. Seals joints in facilities requiring pick-proof and tamper resistance Adhesive for marine applications Hollow block joint repairs Sealing joints in concrete to prevent water intrusion Crack sealer/filler Capping gel for crack-injection Pick-proof, tamper resistance (windows, doors, etc.), Ideal for correctional facilities Great for bonding metal to metal for applications. 25 Off-White Gel Time (60g 75 F) 35 minutes Full Cure Time (Pick-Proof) 72 hours Temperature Range 40 F 110 F

7 SPECIALTY PRODUCTS High Strength Grout, Cementitious Products, Concrete Demolition Ultrabond EGP High Strength Grouting System Ultrabond EGP is a three component, 100% solids, high performance, high strength epoxy grouting system. It is a solvent-free, low-odor, moisture insensitive, prepackaged epoxy grout system. EGP is ideal for precision seating of baseplates, and grouting under heavy-duty equipment. It is ideal as an epoxy grout for concrete patching and overlays. EGP can be mixed to three different consistencies: 1) Trowelable 2) Plastic/Flowable 3) Pourable/Self-Leveling High strength grouting vibratory, high impact, heavy load conditions Patch and Spall repair Patching/repairing warehouse, office and garage floors Machine Base Grouting (heavy impact and vibratory machinery, reciprocating engines, compressors and pumps) Grouting under crane rails Fast strength gain Low exotherm Oil and Chemical Resistant Pre-proportioned kit High strength epoxy grout High effective bearing area Corrosion and impact resistant High vibration resistance Non-shrink Variable ratio fill system: ratio of special blend aggregate to total liquids Tan Thick Grout Gel Time (60g 77 F) minutes Cure Time 24 hrs. Temperature Range 40 F 110 F Hard-Rok Anchoring Cement HARD-ROK Anchoring cement is a high strength, fast setting, non-shrink, nonmetallic cementitious product used for anchoring and grouting applications. This hydraulic cement is quickly and easily mixed with water to either a pourable or putty-like consistency. Anchoring Threaded Rods, Bolts and Rebar Dowels Anchoring Railing, Signs, Posts and Parking Meters Anchoring Machinery Patching Holes and Cracks in Concrete High Strength Fast cure anchoring cement: fast initial set of 15 minutes at 75 F when mixed to fluid consistency Ideal for interior and exterior applications Contains no metals to rust and cause unsightly stains Compressive strength of 7,200 psi in 28 days insures a firm bed in grouting applications Mixed to a free flowing consistency: Flows like pancake batter eliminating the labor required in Roding or vibrating to eliminate voids. See rendering of building in this brochure for applications. 33 Hard-Rok Jet Patch used for runway repair. Hard-Rok Jet Patch JET PATCH is a Portland Cement blend of specialty aggregates and admixtures providing a rapid setting, high strength, durable concrete repair for use on airport runways, taxiways, concrete floors, highway pavements, bridge decks and other applications requiring early resumption of traffic or use. Jet Patch is formulated to meet the requirements of ASTM C928 Packaged, Dry, Rapid Hardening Cementitious Material for Concrete Repair. Excellent for all types of concrete repair applications: bridge decks, concrete pavements and joints, airport runways and taxiways, industrial floors, loading docks, pre-stressed and precast concrete Specifically designed for those applications requiring very rapid strength gain For deeper spalls ( >3 ) add pea gravel. See Installation Instructions for details Thermal expansion & contraction similar to concrete, Freeze-thaw resistant For repairing depths between 1/2 to 3 use as packaged, mixed with water Flowable and Self Compacting Sulfate resistant High early strength with low permeability The Cracker Non-Explosive Cracking Agent The Cracker is a non-explosive cracking agent that can crack any hard rock or reinforced concrete. The Cracker is a universal product which may not only be substituted for explosives, hydraulic wedges, rock-breakers, and concrete-crackers, but can also be used in many places where other methods are impractical. Produced in powder form, The Cracker need only be mixed with water and poured into predrilled holes for dramatic results. KEY USAGE FACTS You ll need to know the following to determine how much product you ll need. What is the size and shape of the object to be demolished? What size pieces are you looking to create? Is there a free edge? Will the substrate be over or under 72 F? Is the substrate reinforced? What is the substrate psi? For complete info, watch our Cracker video on our website and download the Cracker technical manual. SAFE - High safety factor when compared to other methods of demolition QUIET - Ideal for use in or near occupied buildings NON-TOXIC - 100% biodegradable after activated POWERFUL - Breaks concrete from 8 inches to 10 feet thick This brochure is intended to be used as a quick reference guide only. Information is subject to change without notice. Copyright 2013, Adhesives Technology Corp. 0113