AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A AAMA TEST REPORT SUMMARY

Size: px

Start display at page:

Download "AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A AAMA TEST REPORT SUMMARY"

Frederica Lynne Parks
5 years ago
Views:

1 AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A AAMA TEST REPORT SUMMARY Rendered to: GIESSE NORTH AMERICA 2014 Holston Industrial Drive Blountville, TN PRODUCT TYPE: XO Sliding Glass Door SERIES/ MODEL: GOS-S Lift and Slide Door Title Primary Product Designator AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A Positive Design Pressure Negative Design Pressure Operating Force (in motion max ) Air Infiltration Water Penetration Resistance Test Pressure Uniform Load Structural Test Pressure Forced Entry Resistance AAMA Summary of Results Class AW-PG50: Size tested 3124 x 2416 mm (123 x in) - SD SD-AW x 2416 (123 x ) Pa (+50.0 psf) Pa (-50.0 psf) 35.6 N (8 lbf) Prior to and After cycling 0.1 L/s/m 2 (0.01 cfm/ft 2 ) Prior to and After cycling 730 Pa (15.0 psf) ±3600 Pa (75.0 psf) ASTM F Grade 10 Pass Pass Test Completed: 08/08/13 Revision Date: 09/17/13 Reference must be made to Report No. NCTL dated 09/05/13 for complete test specimen description and data. For National Certified Testing Laboratories Jay Leader Technician 1 of 23

2 AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A AAMA STRUCTURAL TEST REPORT NCTL REPORT TO: GIESSE NORTH AMERICA 2014 HOLSTON INDUSTRIAL DRIVE BLOUNTVILLE, TN REPORT NUMBER: NCTL REPORT DATE: 09/05/13 REVISION DATE: 09/17/13 PRODUCT: GOS-S LIFT AND SLIDE DOOR TYPE XO SLIDING GLASS DOOR 2 of 23

3 Report Number NCTL Report Date 09/05/13 Revision Date 09/17/13 Report To Giesse North America 2014 Holston Industrial Drive Blountville, TN Test Date 08/08/13 Specification Performance Results AAMA/WDMA/CSA 101/I.S.2/A NAFS North American Fenestration Standard/Specification for windows, doors, and skylights AAMA/WDMA/CSA 101/I.S.2/A Standard/Specification for Windows, Doors, and Unit Skylights AAMA Voluntary Life Cycle Specifications and Test Methods for Architectural Grade Windows and Sliding Glass Doors AAMA/WDMA/CSA 101/I.S.2/A Class AW-PG50: Size tested 3124 x 2416 mm (123 x in) - SD AAMA/WDMA/CSA 101/I.S.2/A SD-AW x 2416 (123 x ) Description of Specimen Tested Note: All dimensions are in the order (Width x Height x Thickness) unless otherwise noted. Model/ Series GOS-S Lift and Slide Door Configuration OX Sliding Glass Door Overall Frame Size mm x mm (123 x ) Active Panel Size mm x mm ( x ) Fixed Panel Size mm x mm ( x ) Viewing Area 1397 mm x mm (55 x 85.5 ) Frame & Panel Joint Construction Glazing Components Overall Glass Thickness Spacer /Size Glazing System Extruded aluminum with reinforced nylon thermal breaks Frame (1) Screw, mitered, aluminum corner gusset Panel Mitered, slide-fitted double aluminum corner keys mm (0.911 ) Nominal (2) Lites of 6 mm (0.222 ) nominal tempered glass mm (0.467 ) Aluminum desiccant-filled spacer ( A1-D) Interior glazed with interior, exterior glazing gaskets and a silicone heel bead 3 of 23

4 Giesse North America NCTL Weatherstrip (2) Strips bulb-vinyl Jamb stiles, top and bottom rails (1) Strip bulb-vinyl Meeting stiles (1) Strip center fin Size 6.35 mm (0.250 ) Meeting stiles Operating Hardware Locks Keeper Auxiliary Reinforcement Single-handle (3)-point integrated lock system mm (39.25 ) From the bottom of the active lock stile (2)-Point integrated lock system Fixed jamb stile Metal Active and fixed lock jambs at the lock location Rigid vinyl weatherstrip adapter/ interlock Meeting stiles secured with evenly spaced screws Rigid vinyl filler Head and jambs Rigid vinyl track cover with roller guide Interior and exterior sill tracks Plastic end-cap with felt-wrapped foam Each end of the fixed meeting stile Plastic end-cap Each end of the active meeting stile Metal adjustable dual tandem rollers with metal housing mm (9.5 ) From each end of the active bottom rail Aluminum retainer Exterior of the head and interior of the sill secured with evenly spaced screws Plastic end cap Each end of the head and sill retainer Plastic block Each end of the top rails Rubber bumper Each end of the jamb stiles Aluminum cover Meeting stiles and interior head face (2) Aluminum interlock clips Midspan of each meeting stile, each clip was secured with (3) screws Plastic head adapter with felt-wrapped foam Midspan of the head secured with (4) screws No reinforcement employed 4 of 23

5 Giesse North America NCTL Weep Description Custom weep assembly box with felt-wrapped foam secured with (4) screws Midspan of the sill Interior/ Exterior Surface Finish Sealant Material Insect Screen Installation Method Silver painted aluminum Frame and panel corners Silicone No screen employed The door was installed in a 50.8 mm x mm (2 x 12 ) wood buck and was encased with steel. The door was secured to the buck with (1) #8 x mm (2.75 ) flat head screw. At the active jamb, interior track screws were located at mm (6 ) from each end and mm (12 ) on center thereafter. At the fixed jamb, exterior track screws were located at mm (6 ) from each end and mm m (12 ) on center thereafter. From the active jamb, screws were located at mm (6 ) from the end and mm (12 ) on center thereafter at the interior head track to the head midspan. From the fixed jamb, screws were located at mm (6 ) from the end and mm (12 ) on center thereafter at the exterior head track to the head midspan. The sill was pressure-fitted over (6) evenly spaced aluminum plates. Each plate was secured to the buck with (2) #8 x 38.1 mm (1.5 ) flat head screws. The sill was bedded in silicone and the exterior perimeter was sealed with silicone. Test Results - AAMA/WDMA/CSA 101/I.S.2/A & 2005 Paragraph Test 5.2 Operating Force and Force to Latch - Method B (Force Gauge) ASTM E (08) Prior to and After cycling Initiate Motion = 62 N (14 lbf) Allowed (AW Rating 05/08 ) = 178 N (40 lbf) Maintain Motion - Opening = <27 N (<6 lbf) Maintain Motion - Closing = 36 N (8 lbf) Allowed (AW Rating 05/08 ) = 111 N (25 lbf) Latches = 31 N (7 lbf) Allowed = 100 N (22.5 lbf) NOTE: The results above represent the maximum force among all sash tested. Paragraph Test Air Leakage Resistance ASTM E283-04(12) The tested specimen meets or exceeds the performance levels specified in AAMA/WDMA/CSA 101/I.S.2/A and 2005 for air infiltration at 300 Pa (6.2 psf). Prior to and After cycling Maximum Allowable = 1.5 L/s/m 2 (0.3 cfm/ft 2 ) Extraneous Air Leakage Total Air Leakage = 9.86 L/s (20.9 cfm) = L/s (22.1 cfm) 5 of 23

6 Giesse North America NCTL Air Infiltration Rate = 0.1 L/s/m 2 (0.01 cfm/ft 2 ) Paragraph Test Water Penetration Resistance ASTM E547-00(09) and ASTM E331-00(09) Prior to and After Cycling No Leakage after 4 cycles of 5 minutes at 730 Pa (15.0 psf) No Leakage after 1 cycle of 15 minutes at 730 Pa (15.0 psf) NOTE: Tested without insect screen Paragraph Test Uniform Load Deflection at Design Pressure ASTM E330-02(10) No damage after positive No damage after negative 2880 Pa (60.0 psf) held for 10 seconds 2880 Pa (60.0 psf) held for 10 seconds Measured Deflection Positive = mm (0.444 inches) Measured Deflection Negative = 7.47 mm (0.294 inches) Maximum Allowed (L/175 AW) = mm (0.527 inches) Paragraph Test Uniform Load Structural Test ASTM E330-02(10) No damage after positive No damage after negative 3600 Pa (75.0 psf) held for 10 seconds 3600 Pa (75.0 psf) held for 10 seconds Measured Permanent Set Positive = 0.71 mm (0.028 inches) Measured Permanent Set Negative = 0.41 mm (0.016 inches) Maximum Allowed (0.2%) = 4.70 mm (0.185 inches) NOTE: Deflection and Permanent Set measurements taken on the meeting stile over a mm (92.25 ) span. Paragraph Test Forced Entry Resistance ASTM F A SGD Assembly/Grade 10: = Pass Test Results Allowed Hardware Manipulation Test No Entry No Entry Test A1 No Entry No Entry Test A2 No Entry No Entry Test A3 No Entry No Entry Test A4 No Entry No Entry Test A5 No Entry No Entry Test A6 No Entry No Entry Hardware Manipulation Test No Entry No Entry D SGD Assembly/Grade 10: = Pass Test Results Allowed Test D1 No Entry No Entry Test D2 No Entry No Entry Test D3 No Entry No Entry Hardware Manipulation Test No Entry No Entry 6 of 23

7 Giesse North America NCTL NOTE: 1. T1 = 5 minutes, L1 = 1334 N (300 lbf), L2 = 778 N (175 lbf), L3 = 133 N (30 lbf), L4 = 222 N (50 lbf) plus weight of panel. 2. Loads were held for 60 seconds. Paragraph Test Thermoplastic Corner Weld Test (PVC products only) - Pass Paragraph Test Deglazing Test ASTM E987-88(09) Active Panel Stiles 320 N (70.0 lbf) Results Allowed Jamb Stile 22.4% <90% (<100%) Meeting Stile 23.6% <90% (<100%) Rails 230 N (50.0 lbf) Results Allowed Top Rail 14.8% <90% (<100%) Bottom Rail 15.8% <90% (<100%) NOTE: The glass bite was approximately 12.7 mm (0.5 ) This test report was prepared by National Certified Testing Laboratory (NCTL), for the exclusive use of the above named client and it does not constitute certification of this product. The results are for the particular specimen tested and do not imply the quality of similar or identical products manufactured or installed from specifications identical to the tested product. The test specimen was supplied to NCTL by the above named client. No conclusions of any kind regarding the adequacy or inadequacy of the glass in the test specimen are to be drawn from the ASTM E330-02(10) test. Forced entry resistance test equipment used is in compliance with Section 7 of ASTM F test method. Foam tape is mounted to the perimeter of the test buck prior to clamping to the test wall. NCTL is a testing lab and assumes that all information provided by the client is accurate and does not guarantee or warranty any product tested or installed. The results in this report are actual tested values and are applicable to the specimen tested only, using the components and construction methods described herein. 7 of 23

8 Giesse North America NCTL Detailed drawings were available for laboratory records and compared to the test specimen at the time of this report. Component drawings were reviewed for product verification. The bill of materials contains details with any deviations noted. Ambient conditions during the referenced testing are available upon request. A copy of this report along with representative sections of the test specimen will be retained by NCTL. This report does not constitute certification or approval of the product, which may only be granted by a certification program validator or recognized approval entity. All tests were conducted in full compliance with the referenced specifications and/or test methods. This report is the joint property of National Certified Testing Laboratories Inc. and the Client to whom it is issued. Permission to reproduce this report by anyone other than National Certified Testing Laboratories Inc and the Client must be granted in writing by both of the above parties. This report may not be reproduced, except its entirety, without the written consent of NCTL. National Certified Testing Laboratories Jay Leader Technician Robert H. Zeiders, P.E. Vice-President Engineering & Quality NJL/ hl Attachments Appendix A Revision Summary Appendix B Drawings 8 of 23

9 Appendix A Section 1: Component Drawings, with Applicable Part Numbers, Manufacturing and Modeling Details, were Reviewed (as submitted) for Product Verification (Reference: NCTL ) See Attached Documentation; any deviations noted. Note: The above referenced component drawings (if applicable) along with representative sections of the test specimen will be retained per procedure by NCTL. This testing facility assumes that all information provided by the client is accurate. Section 2: Identification Date Page & Revision Original Issue 09/05/13 Not Applicable Revision 01 09/17/13 Replaced drawings at client request 9 of 23

10 Appendix B Drawings 10 of 23

11 11 of 23

12 12 of 23

13 13 of 23

14 14 of 23

15 15 of 23

16 16 of 23

17 17 of 23

18 18 of 23

19 19 of 23

20 20 of 23

21 21 of 23

22 22 of 23

23 23 of 23

AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A TEST REPORT SUMMARY. Rendered to:

AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A TEST REPORT SUMMARY. Rendered to: AAMA/WDMA/CSA 101/I.S.2/A440-08 AAMA/WDMA/CSA 101/I.S.2/A440-05 TEST REPORT SUMMARY Rendered to: AluminTechno LLC. 12 Selitskog Street, Room 211 FEZ Minsk, Minsk District, Minsk Region 220075 Republic