PERFORMANCE REQUIREMENTS AND CRITERIA FOR BASEMENT ENVELOPE SYSTEMS AND TESTING N. SAHAL, E. OZKAN

Size: px
Start display at page:

Download "PERFORMANCE REQUIREMENTS AND CRITERIA FOR BASEMENT ENVELOPE SYSTEMS AND TESTING N. SAHAL, E. OZKAN"

Transcription

1 CIB World Building Congress, April 2001, Wellington, New Zealand Page 1 of 11 PERFORMANCE REQUIREMENTS AND CRITERIA FOR BASEMENT ENVELOPE SYSTEMS AND TESTING N. SAHAL, E. OZKAN Istanbul Technical University, Faculty of Architecture, Istanbul, Turkey ABSTRACT Basement can be a difficult environment in which to build a livable space. It is surrounded by soil that may be damp, wet or frozen. The temperature of the ground surface remains nearly in phase with that of the air, however; below surface, in summer it decreases and in winter it increases linearly with depth. Basements are exposed to dead and live loads of the building as well as the lateral soil loads and sometimes the hydrostatic pressure due to the high levels of groundwater. Therefore, below grade envelope systems are subjected to more temperature changes, structural and moisture loads than that of the above grade; yet, the interior environment is expected to be the same. Basement problems occur because of the poor concordance between users expectations of basements, their construction and the environmental forces with which the basements must meet. Solutions that reduce both building and operational costs while improving indoor environment can only be achieved by establishing performance requirements for basement envelope systems. And also, predicting the behavior of the system under actual in-service conditions by performance test methods. In this paper; the user requirements for basements and the functions of the basement envelope systems are established. The thermal and moisture regimes as well as the structural loads of the basement envelope systems related to the inside and outside environmental agents are identified. The resulting structural and environmental problems are reviewed. How the basement envelope systems are expected to perform under which circumstances are laid out as the performance requirements of the system. The performance criteria of the materials within the envelope system that address the performance requirements is determined. A test method which has been developed to evaluate the performance of strained bituminous waterproofing membranes under hydrostatic pressure is mentioned as an example for performance testing. Finally, the test results are presented and evaluated on the basis of whether the requirement and criteria are attained. KEYWORDS: Performance requirements; performance criteria; performance testing; basement envelope systems; waterproofing. INTRODUCTION Basement is somewhat invisible and the envelope is sometimes ignored component of the building. Until now, the primary concern of the designer and the builder was to meet the safety requirement of the user; therefore, the only function of the basement envelope was established as structural adequacy. The user requirements such as health and comfort were ignored or the environmental agents that affected the basement envelope were not fully recognized; thus, less attention was given to separate the basement indoor climate from the outdoor soil climate. As the basement envelope was exposed to below-grade environmental agents, it often failed to respond to the them and its performance proved to be unacceptable. Leaky and damp basements, cracked walls, frost-heaved walls, the smell of mould and mildew were some of the leading basement problems. These problems not only damaged the basement envelope materials but they also represented a real health hazard. On the other hand, the occupants of most buildings expected that the basement indoor climate would provide a prime living space. In order to achieve an effective control of indoor climate, the occupants took some precautions such as using humidifiers during the winter and dehumidifiers during the summer to maintain an acceptable indoor relative humidity, re-excavating the soil around leaky basements, using extra

2 CIB World Building Congress, April 2001, Wellington, New Zealand Page 2 of 11 equipment for heating and cooling and in extreme cases, rebuilding the basement envelope. In the end, the cost of these precautions passed on to the homeowners. Therefore, the occupants increasingly demanded that the basement envelope should provide an effective environmental separation besides structural adequacy. Today s home buyers want a healthy and energy-efficient home which they can not only afford to buy but, also afford to live in. In order to develop a better understanding of the intended role that is to be played by the basement envelope for the people designing and constructing it, the need to establish performance requirements and criteria as well as developing performance evaluating techniques for the systems and the materials have arisen. PERFORMANCE REQUIREMENTS FOR BASEMENT ENVELOPE SYSTEMS The aim is to build a livable and usable basement indoor environment that satisfies user requirements. The user requirements for basements are determined as thermal comfort, safety and tightness. The other user requirements, such as visual comfort, acoustic comfort, hygiene, etc. are excluded as they are usually treated in the context of the entire building. According to the specified user requirements, the overall function of the basement envelope system, in conjunction with above-grade, is to provide environmental separation, strength and stability to the loads of the building and structural support to the loads that are generated from environmental agents such as groundwater. The basement envelope system can be capable of functioning as intended, if performance requirements are satisfied. Performance requirements for basement envelope systems are developed from the performance analysis of the system; where the environmental agents that affect the system are identified, they are than related to the corresponding properties of the system and the processes involved in the interaction of the system with its environment are analyzed, as the moisture regime, thermal regime and the loads of the system. The moisture regime of the basement envelope system The environment that surrounds the basement envelope is the soil mass and the indoor climate; therefore, the sources of water that build up the moisture regime of basement envelope system are splash water, water vapor in the soil, seepage water, capillary water, groundwater, adsorbed water, moisture in concrete after construction, exterior humid air that enters the basement and condenses on cooler surfaces and water vapor from interior sources, Figure 1. The forces which drive the moisture into the openings in the building envelope from the exterior are, gravitational forces, capillary suction, vapor pressure and differences in air pressure. Differences in air pressure and vapor pressure are also responsible for the penetration of moisture into the openings in the basement envelope from the interior. Figure 1. The Moisture Regime of the Basement Envelope System

3 CIB World Building Congress, April 2001, Wellington, New Zealand Page 3 of 11 Seepage water is the water that drains from the soil after a rainfall by the force of gravity acting on it. Water seeping along the basement wall-soil interface may find an easier path along a crack through the basement wall and penetrate into the basement envelope due to the gravity. When seepage water collects within the pores of the soil on a strata, the forces of gravity cause a build up of hydrostatic pressure within the bulk water. When groundwater stands against the basement walls and floor, hydrostatic pressure will develop which can force large quantities of water through pores of the material used in the envelope into the basement. Capillary water is the water that moves by capillary forces above the water table. This water may be drawn into the porous materials used in the basement envelope under the action of capillary suction. Once in the wall or floor, the capillary water can evaporate to the interior of the basement. Capillary suction is related to the porosity of the materials used in the envelope as well as the fine cracks in the envelope. Dampness of basements is often attributable to capillary water. Splash water may deposit a film of water on the above-grade portion of the basement wall and porous materials may also draw the water into the envelope by capillary suction. The air in the soil and the air in the basement contain water in the form of vapor. At times, vapor can diffuse from the wetter soil through the envelope toward the dryer basement interior, at times from the basement toward the soil and most of the time both kinds of diffusion are found at the same time but in different parts of the basement envelope; the driving force being the vapor pressure differential. In most houses, a stack effect is created when warm air in the basement rises. This induces a negative pressure on the basement and draws vapor in the soil in through any cracks in the basement envelope. Adsorbed water is water that is relatively firmly held by surface forces developed between the polar water molecules and hydrophilic materials. The amount held by a surface in this state depends on the relative humidity of the environment. It is responsible for part of the water diffusion through building materials. It plays an significant part in moisture in construction and seasonal storage of water in building materials. In summer time, basement windows may be opened for fresh air. If the outside air is warm and humid, it will condense on the cool basement wall and floor surfaces. Leakage will occur on the surface of the wall or condensed water will accumulate on the floor. Water added to fresh concrete performs two functions; to provide workability and to react chemically with the cement. Unfortunately, the amount of water required for workability exceed the amount required for chemical reaction. Most of the unreacted water will be lost by drying. The moisture regime of the basement envelope system often results in moisture problems such as decay of organic and inorganic materials, water leaking on walls, standing water on floor, dampness, humid air, odor, mould and mildew, deterioration of basement finishing materials, efflorescence, etc. The thermal regime of the basement envelope system Besides the moisture regime, the thermal regime also influences the performance of basement envelope system. The environmental agents that build up the thermal regime of the system are soil temperature and basement indoor air temperature. Soil temperature is affected by many factors; terrain features such as vegetation and slope orientation, the properties of soil such as thermal conductivity and water content, and meteorological elements, primarily, snow, solar radiation and air temperature. Outdoor air temperature changes from day to night, from day to day and from season to season. Soil temperature also varies, only here the rate of change is slow while the amplitude of change is reduced. Soil temperature change reflects outdoor air temperature change, only here it can take a long time before air temperature change is reflected in the soil; the farther we go from the soil surface the longer it takes. The time lag is due to the thermal inertia of the soil and its water content. The time lag is minimal close to the ground surface. Assuming that the basement air temperature and humidity are the same as those outdoors in winter and in summer and the temperature of the uninsulated basement envelope approaches the temperature of the soil adjacent to it; in winter, the soil temperature between the basement floor and usually one meter below grade is usually higher that the basement air temperature, so that heat flows from the soil into the basement interior. In summer, it is in the opposite direction to the heat flow in winter. In both cases, the energy consumed for heating and air-conditioning increases. The temperature of the soil adjacent to the basement envelope is important not only because of its impact on heating and airconditioning loads but also because it has an effect on the direction of vapor diffusion between the soil and the basement interior. In summer, warm, moist air in the basement interior may condense on cold wall and floor surfaces as the soil temperature may be below the dewpoint temperature of the outdoor

4 CIB World Building Congress, April 2001, Wellington, New Zealand Page 4 of 11 air. Further, in winter, vapor in the relatively warm moist soil may diffuse through the basement envelope into the basement interior, in response to a vapor pressure gradient which is in the opposite direction to the summer gradient. In winter and in summer, the materials used in basement walls will experience different thermal movements varying with depth in response to the variation of soil temperature with depth. Further, the maximum soil temperature difference between winter and summer occurs 0.05 m. below grade; therefore, the basement wall may undergo the highest thermal movement at this depth, Figure 2. If these thermal movements are restrained, stresses may induce within the material or between the materials used in the wall, resulting in deformations such as crack formation. Figure 2. The Thermal Regime of the Basement Envelope System The loads of the basement envelope system The loads that affect the basement envelope system are the dead and live loads of the above-grade structure, lateral soil loads, hydrostatic pressure due to the high level of groundwater and heaving pressures that is generated from frost action. One of the loads acting on basement wall is the sum of the dead, live and wind loads of the above-grade structure which is transferred to it vertically. Besides, the basement wall and floor have self-loads; their own weight and user loads. Basement wall is also exposed to the lateral loads from the soil. The lateral loads on the wall depend on the height of the fill, the soil type, soil moisture content and whether the building is located in an area of low or high seismic activity. If groundwater exists, water may exert hydrostatic pressure against the basement wall and floor area depending on the height of the water table, Figure 3. If the sum of the water pressure and the bearing capacity of the soil which has lessened as much as the water pressure exceed the dead load of the building, the building may float. When the basement envelope can not withstand the vertical, lateral, hydrostatic pressure and self loads and can not transfer the loads to the ground in such a way that the stresses developed in the material are not within the safety limits of strength of these materials and within the safety limits of soil bearing capacity, deformations may occur. The deformations which lead to basement envelope failures are bowing, vertical or horizontal cracking of basement walls or floor and distortion of window and door frames. Frost heaving of unheated basement may occur if the envelope is placed above the frost line. During ice lens growth at the frost line, most of the volume change results in an upward displacement of the frozen layer. The heaving displacements are transmitted to the envelope and displacements of the basement envelope occur unless the dead load of the building exceed the uplift force. Adfreezing may occur if the soil freezes to the surface of the wall of the unheated basement. Heaving pressures developing at the base of the freezing zone are transmitted through the adfreezing bond to the basement wall, producing uplift forces capable of vertical displacements which leads to structural damage.

5 CIB World Building Congress, April 2001, Wellington, New Zealand Page 5 of 11 Figure 3. The Loads of the Building Envelope System Basement problems occur because of the poor concordance between occupants expectations of basements, their design and construction and the environmental agents which the envelope must contend. In order to avoid the failures, how the envelope is expected to perform under the dictated conditions to satisfy the user requirements, must be stated. The statements are the performance requirements for the basement envelope system which are given in Table 1. As there are various building systems, the two functions of the basement envelope system which are to provide strength and stability to the loads of the building and structural support to the loads that are generated from environmental agents are considered separately. In a load-bearing wall structure, the basement wall serves as the structural as well as the external division element; therefore, it must fulfill both functions. On the other hand, in a framed structure, the structural component of the basement wall is the column which must fulfill both functions; while, the external division element must only provide structural support to the loads that are generated from the environmental agents. Durability is a major issue in basement envelope systems. Basement envelope system must create a protective environment for its components where they will be able to preserve their properties without any degradation and perform as intended over the service life of the system. PERFORMANCE CRITERIA FOR THE COMPONENTS OF BASEMENT ENVELOPE SYSTEMS The performance requirements are the key elements of the envelope design. In the design process, the performance requirements that will be addressed must be determined according to the intended use of the basement and the external agents. For instance, if the basement will serve as a structural foundation only, then the envelope must be designed to address the performance requirements related to the structural functions. The floor which separates the basement and indoors is now the envelope that must address all performance requirements. The envelope has a structural component which must resist the vertical loads of the above-grade structure, lateral soil loads, hydrostatic pressure due the groundwater and self-loads and must transfer the loads to the ground safely in such a way that the stresses developed in the material are within the safety limits of the strength of these materials, the bearing capacity of the soil is not exceeded and the settlement of the structure is not excessive. For frost-heaving and adfreezing to occur, there must be three conditions; the soil must be frost-susceptible, water must be available in sufficient quantities and cooling conditions must cause the water and soil to freeze. If any one of these factors can be controlled, frost action can be prevented. Since it is seldom economically possible to control soil temperature, frost action is usually prevented by separating the envelope from the surrounding soil with a drained zone of material such as gravel or a thermal insulation material installed on the exterior of the wall.

6 CIB World Building Congress, April 2001, Wellington, New Zealand Page 6 of 11 The penetration of seepage water into the basement wall can be prevented by controlling the amount of rainwater or surface water entering to the soil adjacent to the basement wall, controlling the number of openings or holes in the wall and/or controlling the driving force which is gravity. In order to control the amount of rain or entering to the soil adjacent to the basement wall, overhangs must be designed around the perimeter of the roof, gutters must collect rainwater falling on the roof and downspouts must direct water away from the soil adjacent to the basement wall. Ground must slope away from basement wall in order to redirect surface runoff. An impermeable material must be used for backfilling the upper portions of the basement wall. Gravity can be controlled by the use of a drain screen immediately adjacent to the basement wall linked to the perimeter subsurface drainage system. The most common examples of the drain screen is free-draining backfill material, drainage mats and thermal insulation materials with drainage properties. A dampproofing material can be installed on the exterior of the basement wall to eliminate the openings or holes in the wall. The dampproofing material must also be linked to the perimeter subsurface drainage system where perforated drainpipes in a gravel bed along the footing or beneath the slab are located to drain water to a sump. These strategies will also prevent the development of groundwater in the soil adjacent to the basement wall and floor; but, in sites where groundwater already exists, the penetration of water into the basement envelope will be prevented by the provision of a continuous waterproofing membrane installed on the exterior of the basement wall and floor. surface drainage must also be provided to prevent the rising of the water table. A designer can prevent the penetration of capillary water into the basement envelope by controlling the availability of capillary water, sealing capillary pores, and/or making capillary pores larger. The traditional way is to use a material that does have any pores such as a dampproofing material applied onto the exterior surface of the wall where it breaks the capillary continuity between the soil and material used in wall; or to use materials that does not support capillarity as a result of their large pore size such as granular pad placed under the floor slab. The control of heat flow is an essential element of environmental separation. All the components of the envelope have more or less thermal resistance and all of them are involved in heat transfer. But, an effective thermal resistance of the assembly can be achieved by the provision of a continuous thermal insulation material with adequate thermal resistance within the envelope. The key question in the design process is whether to place the insulation inside or outside the basement wall and floor. Rigid insulation placed on the exterior surface of a wall and floor has some advantages over the interior placement in that it can provide continuous insulation with no thermal bridges, protects and maintains the other components of the envelope, minimizes moisture condensation problems, prevents thermal movements and does not reduce interior basement floor area. Interior insulation is an alternative to exterior insulation and it is mostly popular for retrofit situations. It is simpler to install on existing wall and floor and thermal insulation material costs may be low since almost any insulation material may be used. In general, vapor diffusion retarders are located on the exterior of the wall to retard the inward flow of vapor by diffusion from the surrounding soil into the basement interior. Dampproofings typically have high resistance to vapor flow; therefore, they act as vapor diffusion retarders. Vapor diffusions from the surrounding soil into the basement wall can also be controlled by thermally insulating the wall from the exterior. Vapor diffusion under the basement floor is controlled by installing a vapor diffusion retarder between the slab and the granular pad. Vapor diffusion from the basement interior into the wall and is controlled by locating a vapor diffusion retarder to the interior of the wall. Interior moisture levels can be controlled as well. Diffusion of construction moisture from concrete walls into the basement interior can be controlled by locating a vapor diffusion retarder at the interior surface of the wall. Another practice is to apply the finishing materials to the interior surface of the wall after the drying of the construction moisture is over. The key factor in the design process is that balance of vapor flow is achieved in every point within the envelope without condensation occurring. The moisture in the soil or basement interior air can also be transported as a result of air movement. The air movement from the surrounding soil into the basement interior or via versa can be controlled by controlling the openings or holes in the assembly as well as air pressure differential. As most of the materials used in the envelope are relatively air impermeable such as polyethylene, concrete, the key factor in the design is to provide the continuity of the materials within the envelope.

7 CIB World Building Congress, April 2001, Wellington, New Zealand Page 7 of 11 In the design process of basement envelope, the achievement of effective environmental separation function is usually a difficult practice as the prevailing conditions such as climate changes on a hourly, daily and seasonal basis. Using one component in the envelope which address a requirement for a prevailing condition at a period may cause failure in the envelope in the following period in which another condition prevails. For example, when the basement air temperature and humidity are the same as those outdoors in winter and in summer and the temperature of the uninsulated basement envelope approaches the temperature of the soil adjacent to it; the heat flow from the soil into the basement interior in winter or the reverse in summer, may be controlled by thermally insulating the wall from the interior. But condensation between the interface of the wall and the thermal insulation material which has high vapor permeability can be expected in the summer. Therefore, in the design process, the roles of each material within the system must be evaluated on a full year basis. Basement envelope system involves multiple materials or system of materials which one of them must at least satisfy one requirement of the system. Some materials address a single requirement; for instance, thermal insulation material placed on the interior of the wall only controls heat loss. Some materials address multiple requirements; for instance, a bituminous liquid applied on the exterior of the wall surface will serve as a dampproofing as well as a vapor diffusion retarder. One material can address most of the requirements depending on how stringent the requirements are for that particular circumstances. For the materials to meet the given role in the envelope system, the expected property or the properties of the material must be stated as the performance criteria of the material. The components of the basement envelope system which address the performance requirements and their expected properties in order to satisfy the requirements, namely, the performance criteria of the components are given in Table 2. The basement envelope as a system will achieve satisfactory performance when all the components that address the needed performance requirements are put together and that all of them work together as intended. PERFORMANCE TESTING: AN EXAMPLE After the fundamental performance requirements for basement envelope systems are derived from the user s needs, the performance criteria for the components of the envelope which address the requirements are established. In order to find out, whether or not the requirements are met by the performance criteria, performance evaluation techniques have to be developed in which the typical conditions of real use are simulated. In the following section, a test method which has been developed to evaluate the performance of bituminous waterproofing membranes under hydrostatic pressure will be mentioned as an example for performance testing, (Sahal, 1999). Basements wall and floor of a new constructed building are sometimes exposed to water that exerts hydrostatic pressure from the outside due to the existence of high level of groundwater. The basement envelope system is expected to resist the hydrostatic pressure loads as well as to prevent the penetration of water under pressure. The structural components of the system resist the hydrostatic pressure loads; therefore, they have to provide strength and stability to the loads. When the groundwater is the concern, the basement wall and floor are designed as reinforced concrete walls and reinforced concrete structural slab. Bituminous membranes are used as one of the waterproofing materials in order to prevent the transmission of water under pressure; therefore, they are expected to have low permeability. To perform satisfactorily, bituminous waterproofing membranes must surround the entire structure continuously. To resist the effects of hydrostatic pressure, the membrane, weak in itself, must be loaded by a mass of material at one side and must be protected from damage at the other side. Therefore, the bituminous membranes are sandwiched between two layers in an external tanking arrangement where the tanking is protected by a protective layer on the excavation side with the structural wall and floor slab internally, Figure 4. In the actual service conditions of the membrane, the membrane remains under compressive pressure between the structural floor slab especially under the columns where the loads are relatively high and the concrete blinding. Thus, the plastic bituminous membranes follows the structural deformation. In external tanking, tensile stresses are developed within the reinforced concrete structural slab in contact with the membrane; therefore, membranes are subjected to tensile stresses and they deform as

8 CIB World Building Congress, April 2001, Wellington, New Zealand Page 8 of 11 the reinforced concrete slab. During construction; after the pumping out of the groundwater is stopped, the rising water will fill the air pockets and push the air to the membrane. The air under pressure will force the membranes which may not be airtight and as a result, air will penetrate through the membranes providing easy access for the water afterwards. The concrete blinding in contact with the membrane, may be attacked by harmful chemicals that are found in the groundwater such as sulphates. Sulphates will react with the hardened cement paste of the concrete to form either ettringite or gypsum which eventually will cause the cracking and spalling of the concrete unless preventive measurements are taken. Shrinkage may occur in concrete building elements when concrete losses its construction moisture. The resultant movement is another cause of cracking on the surface of the structural floor slab and reinforced concrete walls. Due to the cracking, a narrow part of the membrane may strain excessively. Concisely, the mechanical agents that are generated by the construction strain the bituminous membranes excessively. The mechanical properties of the bituminous membranes may withstand the stresses satisfactorily but on the other hand it is not known whether the strained bituminous membranes will still maintain its low permeability property efficiently or lose its watertightness integrity under water pressure. Therefore, the performance of both strained and unstrained bituminous membranes under water that exerts pressure must be determined by a convenient test method. Figure 4. External Tanking Current test methods that determine the resistance of bituminous membranes to water pressure have been examined and it has been found out that these methods were testing for the purpose of quality control, they were not testing for the purpose of predicting in-service performance. Therefore, a test method has been developed where the effects of the mechanical agents on the membranes are simulated, one side of the strained membranes are then exposed to water pressure and whether or not water molecules has penetrated through the membrane is determined from the other side of the membrane. Besides, the amount of transmitted water molecules either in liquid or vapor form is measured in order to calculate the coefficient of permeability constants of the membranes according to the D arcy Law. The test apparatus consists of a hydrostatic testing equipment and a measurement system. Hydrostatic testing equipment includes, a chamber, a rubber gasket, a steel plate which has a gap in the body, a clamping bracket and fasteners to tighten the clamping bracket to the chamber. The strained bituminous membrane is placed between the rubber gasket and the steel plate. The measurement system consists of an absolute humidity sensor, a signal conditioning circuitry and a multimeter. Several tests have been conducted on the commercially available oxidized and modified bituminous membranes; but, the results of the two tests will be mentioned here. The samples used in both tests are polyester reinforced (180 gr/m 2 ), APP modified bituminous membrane with a thickness of 3 mm. In one of the tests, to simulate the strain of the membranes when subjected to the compressive pressure under the column bases, one of the membrane samples was strained at 0.5 N/mm 2 of compressive pressure in an universal testing machine. The same simulation was conducted on the other sample where the compressive pressure was 0.8 N/mm 2. Then one side of the strained membrane sample (0.5 N/mm 2 ) was exposed to a 0.25 N/mm 2 of air pressure for 2 hours; then, the same side was exposed to a 0.25 N/mm 2 of water pressure for 96 hours in the hydrostatic testing equipment. Meanwhile, the amount of water molecules (gr/m 3 ) that have been transmitted through the

9 CIB World Building Congress, April 2001, Wellington, New Zealand Page 9 of 11 membrane to the other side was collected in the steel plate s gap which is tightly sealed from the outer environment and measured per minute for 96 hours with the measurement system. The measured data is recorded and stored in a computer program to be evaluated periodically. The same test was conducted on the other membrane sample. The test result of the membrane sample which was strained at 0.5 N/mm 2 of compressive pressure showed that it maintained its low permeability property under these conditions as there was no increase in the amount of water molecules in the gap. The test result of the membrane sample which was strained at 0.8 N/mm 2 of compressive pressure is given in Figure 5. From the figure, it can be seen that after 77 hours, the membrane has started transmitting water molecules into the gap. Water in the gap condenses depending on the air temperature of the gap. In the test, approximately 14 gr. of water molecules have been transmitted within 4 hours and then condensation had occurred in the gap. In external tanking, the amount of transmitted water molecules in vapor state may increase the moisture content of the reinforced concrete structural slab or water may condense in the slab depending on its temperature. This may lead to the corrosion of the steel reinforcements. In winter, the capillary water may be absorbed by the thermal insulation material depending on its water absorbing property, leading to deterioration of the insulation. In summer, condensed water may dry into the basement interior if the thermal insulation material has high vapor permeability. It can be concluded that the performance criteria of the bituminous membranes will meet the performance requirement of the basement envelope systems when they are only subjected to compressive stresses between N/mm 2. Figure 5. The Performance of Strained Bituminous Membrane Under Hydrostatic Pressure Absolute humidity (gr/m 3 ) 28,00 26,00 24,00 22,00 20,00 18,00 16,00 14,00 12,00 10,00 8, Tim e (hour) CONCLUSION There are many different approaches to building a basement envelope and more are emerging every year. All should be capable of functioning as intended, if performance requirements and criteria are satisfied under the dictated conditions. The benefits of the satisfactory performance of basement envelope system will be creation of more comfortable above-grade spaces, reduction in homeowner s utility bills, creation of more usable, comfortable below-grade spaces as well as avoidance of costly moisture and structural problems. REFERENCES Sahal, N., Ozkan, E Performance of strained bituminous waterproofing membranes under hydrostatic pressure. In Proceedings, 1999 Durability of Building Materials & Components 8,

10 CIB World Building Congress, April 2001, Wellington, New Zealand Page 10 of 11 User Requirements Table 1. Performance Requirements For Basement Envelope Systems, (B.E.S.). Agents Functions of the B.E.S. Main Sub-Agents Agents Performance Requirements To provide structural support to the loads that are generated from environmental agents Dead loads Lateral soil load B.E.S. must resist lateral loads from the soil. Safety To provide strength and stability to the loads of the building To provide structural support to the loads that are generated from environmental agents Loads Gravity Vibration Live loads Soil pressure The loads of the above structure and self-loads User loads Hydrostatic pressure due to the groundwater Seismic loads B.E.S. must transfer load evenly to the soil. B.E.S. must resist the loads of the above structure and must self-support. B.E.S. must resist user loads. B.E.S. must resist the hydrostatic pressure due to the groundwater. B.E.S. must resist the seismic loads. Tightness Thermal Comfort To provide effective environmental separation Water Air Heat Heaving pressures generated from frost action B.E.S. must prevent adfreezing; frost penetration control. Splash water B.E.S. must prevent the penetration of splash water. Capillary water B.E.S. must prevent the penetration of capillary water. Soil Seepage water B.E.S. must prevent the penetration of seepage water. Groundwater B.E.S. must prevent the penetration of groundwater. Water vapor B.E.S. must control the vapor flow and prevent condensation. Basement interior Water vapor B.E.S. must control the vapor flow and prevent condensation. Basement wall and Released moisture of B.E.S. must control the released moisture of the floor construction construction. B.E.S. must control the air movement. Soil temperature B.E.S. must control the heat flow and thermal Basement indoor air temperature bridges must be avoided. Durability.

11 CIB World Building Congress, April 2001, Wellington, New Zealand Page 11 of 11 Table 2. Performance Criteria for the Components of Basement Envelope Systems, (B.E.S.) Performance Requirements Components of the B.E.S. Performance Criteria B.E.S. must resist lateral loads from the soil. B.E.S. must transfer load evenly to the soil. B.E.S. must resist the loads of the above structure and must self-support. B.E.S. must resist user loads. B.E.S. must resist the hydrostatic pressure due to the groundwater. B.E.S. must resist the seismic loads. B.E.S. must prevent adfreezing; frost penetration control. The structural components of the B.E.S The structural components must resist and transfer loads such that strength of materials and soil bearing capacities are within safety limits. Provision of a drain screen, subsurface drainage, thermal insulation material Maximum drainage capacity, effective thermal resistance B.E.S. must prevent the penetration of splash water. Dampproofing, waterproofing, Low capillarity, low permeability B.E.S. must prevent the penetration of capillary Dampproofing, waterproofing, provision of granular Low capillarity, low permeability water. pad B.E.S. must prevent the penetration of seepage water. Dampproofing, waterproofing, provision of surface drainage, drain screen and subsurface drainage Low capillarity, low permeability, maximum drainage capacity B.E.S. must prevent the penetration of groundwater. Waterproofing, provision of surface drainage Low permeability, B.E.S. must control the vapor flow and prevent Vapor retarder, dampproofing, waterproofing, High vapor diffusion resistance condensation, (vapor in the soil) B.E.S. must control the vapor flow and prevent Vapor retarder, provision of thermal insulation High vapor diffusion resistance condensation, (vapor in the interior) B.E.S. must control the released moisture of the Vapor retarder, dampproofing, thermal insulation High vapor diffusion resistance construction. B.E.S. must control the air movement. Air impermeable materials, provision of continuity Low air permeability B.E.S. must control the heat flow and thermal bridges must be avoided. Thermal insulation materials Effective thermal resistance

PERFORMANCE OF STRAINED BITUMINOUS WATERPROOFING MEMBRANES UNDER HYDROSTATIC PRESSURE Performance of bituminous membranes

PERFORMANCE OF STRAINED BITUMINOUS WATERPROOFING MEMBRANES UNDER HYDROSTATIC PRESSURE Performance of bituminous membranes PERFORMANCE OF STRAINED BITUMINOUS WATERPROOFING MEMBRANES UNDER HYDROSTATIC PRESSURE Performance of bituminous membranes N. SAHAL and E. ÖZKAN Istanbul Technical University, Faculty of Architecture, Istanbul,

More information

Insulating Basements: Part 1 Fundamentals

Insulating Basements: Part 1 Fundamentals The Pennsylvania Housing Research Center Insulating Basements: Part 1 Fundamentals Builder Brief: BB0510 Brian Wolfgang, PHRC Fellow INTRODUCTION The perception of a basement has changed significantly

More information

Foundations. Issue. Slab-On-Grade Liquid Water Control (See Figure 2-2) Goals. Guidance

Foundations. Issue. Slab-On-Grade Liquid Water Control (See Figure 2-2) Goals. Guidance www.epa.gov/iaq/moisture Foundations Issue Building foundations are vulnerable to moisture problems for a number of reasons, including: Water from rain and from plumbing leaks is drawn by gravity to foundations,

More information

Background Basement Thermal Behavior

Background Basement Thermal Behavior Kohta Ueno Basement Insulation: What to Do & What Not to Do March 29, 2012 Background Basement Thermal Behavior Basement Insulation: What to Do & What Not to Do 2 Basement/Foundation Energy Use Basement

More information

FirstEnergy Program Overview

FirstEnergy Program Overview FirstEnergy Program Overview Builder incentives $400 per unit + $0.10/kWh in projected savings Eligibility Located in service area of a FirstEnergy Utility Certificate of Occupancy Dates: FirstEnergy Ohio

More information

2/23/2009 R15-R20R20

2/23/2009 R15-R20R20 Foundations What is important to know about foundations? You (probably) won t design it What are the components that make up a properly designed and built foundation? Determine whether house has a good

More information

Thermal Patterns Created By Moisture Accumulation Within Exterior Masonry Walls by A. Colantonio* and G. Desroches ** * Public Works And Government Services Canada, Ottawa, Canada ** Public Works And Government

More information

Priorities for Dealing with Water. Freezing/Frost Heave Issues. Freezing/Frost Heave Issues. Previous Work. Freezing/Frost Heave Issues

Priorities for Dealing with Water. Freezing/Frost Heave Issues. Freezing/Frost Heave Issues. Previous Work. Freezing/Frost Heave Issues Builder's Handbook Review November 15, 2011 Background Kohta Ueno Foundations: Research Results and Builder s Handbook Review November 15, 2011, Minneapolis, MN 2 Foundations w. bulk water issues Background

More information

Basements are Changing. Basements Part of the Enclosure. Basements. Control: Moisture. Moisture: Old ideas. Energy Efficient, Durable, Healthy

Basements are Changing. Basements Part of the Enclosure. Basements. Control: Moisture. Moisture: Old ideas. Energy Efficient, Durable, Healthy Basements are Changing John Straube, Ph.D., P.Eng Basements: New & Retrofit Energy Efficient, Durable, Healthy Building Science Corporation presented by www.buildingscience.com Increasingly used as living

More information

This presentation. Functions of the building enclosure. University of Waterloo and Balanced Solutions. Straube Presentation Building Canada

This presentation. Functions of the building enclosure. University of Waterloo and Balanced Solutions. Straube Presentation Building Canada Hygrothermal Basement Performance, or Why do we get water when we dig holes in the ground? Dr John Straube October, 2004 This presentation What do basements do Examine performance Why problems What solutions

More information

6. Moisture Design. Objectives: 3. Prevent vapor condensation (surface, concealed) 4. Prevent rain penetration

6. Moisture Design. Objectives: 3. Prevent vapor condensation (surface, concealed) 4. Prevent rain penetration 6. Moisture Design Objectives: 3. Prevent vapor condensation (surface, concealed) 4. Prevent rain penetration Vapor Condensation More new bldgs are susciptable to vapor condensation because of: 2. 1. 2.

More information

Building Envelope Solutions, Inc. Identifying solutions for better building performance

Building Envelope Solutions, Inc. Identifying solutions for better building performance Building Envelope Solutions, Inc. Identifying solutions for better building performance The BES/FOAM-TECH AVID System (Air/Vapor/Insulation/Drainage) The AVID System was developed by Building Envelope

More information

Basements: New & Retrofit

Basements: New & Retrofit John Straube, Ph.D., P.Eng Basements: New & Retrofit Energy Efficient, Durable, Healthy Building Science Corporation presented by www.buildingscience.com This presentation Basement functions Basement Performance

More information

2001 National Workshop on State Building Energy Codes July th, 2001 Burlington, Vermont

2001 National Workshop on State Building Energy Codes July th, 2001 Burlington, Vermont 2001 National Workshop on State Building Energy Codes July 16-19 th, 2001 Burlington, Vermont A Systems Engineering Approach to the Design of Energy and Resource Efficient Homes Presented By: Mark LaLiberte

More information

This presentation. Basements: New & Retrofit. Basements Part of the Enclosure. Basements are Changing. Basement functions Basement Performance

This presentation. Basements: New & Retrofit. Basements Part of the Enclosure. Basements are Changing. Basement functions Basement Performance This presentation John Straube, Ph.D., P.Eng Basements: New & Retrofit Energy Efficient, Durable, Healthy Building Science Corporation presented by www.buildingscience.com Basement functions Basement Performance

More information

Sloped Roofs vs Walls. Problems. Review Roof Components. University of Waterloo and Balanced Solutions

Sloped Roofs vs Walls. Problems. Review Roof Components. University of Waterloo and Balanced Solutions Roofs, Cathedral Ceilings, Venting, Non-Vented Dr June, 2005 This presentation Scope: Pitched, Wood, Roofs Performance Problems Vented, cathedral, unvented etc What solutions www.balancedsolutions.com

More information

Smart Vapor Retarders

Smart Vapor Retarders CertainTeed Smart Vapor Retarders Insulation B UILDING S CIENCE SMART VAPOR RETARDERS: A TECHNOLOGY PRIMER For years, builders have relied on a dual climate-zone classification for the placement of vapor

More information

Preventing Mold and Other Moisture Problems

Preventing Mold and Other Moisture Problems Preventing Mold and Other Moisture Problems A Community Workshop presented by William W. Hill, Ph.D. Department of Urban Planning, Ball State University Sponsored by the Community Outreach Partnership

More information

Foundations. Foundations form the major part of a buildings substructure (along with the rising walls, hardcore and ground floors)

Foundations. Foundations form the major part of a buildings substructure (along with the rising walls, hardcore and ground floors) Foundations Foundations form the major part of a buildings substructure (along with the rising walls, hardcore and ground floors) Once the substructure is complete the building is out of the ground and

More information

Welcome to this continuing education seminar. This is the first of two parts of the High- Performance Building series.

Welcome to this continuing education seminar. This is the first of two parts of the High- Performance Building series. Welcome to this continuing education seminar. This is the first of two parts of the High- Performance Building series. 1 3 6 7 8 An enclosure s basic function is to separate the outside from the inside.

More information

The Building Envelope Defined

The Building Envelope Defined Learning Objectives 1. The purpose of the building envelope 2. The energy code s definition of the building envelope 3. The exterior forces that act on the building envelope 4. The interior forces that

More information

Water Management & Damage Prevention: A Guide for Homeowners

Water Management & Damage Prevention: A Guide for Homeowners Water Management & Damage Prevention: A Guide for Homeowners This article provides homeowners with basic information to make these decisions and take the appropriate actions to keep their homes dry and

More information

Crawl Space Moisture Control

Crawl Space Moisture Control Crawl Space Moisture Control Crawl space foundations are found in many homes. Typically, these foundation types are equipped with operable vents designed to provide ventilation for moisture control. Unfortunately,

More information

Groundwater Seepage. Causes of Basement Seepage and Leaks Hydrostatic Pressure

Groundwater Seepage. Causes of Basement Seepage and Leaks Hydrostatic Pressure Groundwater Seepage The following guide can be used by you and your crews when assessing seepage at a property. Bear in mind that this guide is not all-inclusive, and should be used in a supplementary

More information

Of Building Science: From Control Layers to High Performance Enclosures

Of Building Science: From Control Layers to High Performance Enclosures Of Building Science: From Control Layers to High Performance Enclosures Energy Design Conference February 24, 2016 Duluth, MN Patrick H. Huelman Cold Climate Housing Coordinator University of Minnesota

More information

10 EXTREME BASEMENT PANELS

10 EXTREME BASEMENT PANELS 10 EXTREME BASEMENT PANELS On Granular Footings 1. The type of soil is a factor in determining foundation construction details such as footing design, backfill, and drainage provisions. Soils are classified

More information

Mold in Building Constructions in the Nordic Countries With Emphasis on Roofs

Mold in Building Constructions in the Nordic Countries With Emphasis on Roofs Mold in Building Constructions in the Nordic Countries With Emphasis on Roofs Erik Brandt Danish Building Research Institute (SBI) Tommy Bunch Nielsen Danish Roofing Advisory Board (TOR) Roof Consultants

More information

THERMAL PERFORMANCE OF WALL-ROOF INTERSECTION AREAS IN THE EXTERNAL ENVELOPE OF RESIDENTIAL BUILDINGS M.C. ALTUN

THERMAL PERFORMANCE OF WALL-ROOF INTERSECTION AREAS IN THE EXTERNAL ENVELOPE OF RESIDENTIAL BUILDINGS M.C. ALTUN CIB World Building Congress, April 2001, Wellington, New Zealand Page 1 of 9 THERMAL PERFORMANCE OF WALL-ROOF INTERSECTION AREAS IN THE EXTERNAL ENVELOPE OF RESIDENTIAL BUILDINGS M.C. ALTUN Faculty of

More information

Technical Notes 24G - The Contemporary Bearing Wall - Detailing [Dec. 1968] (Reissued Feb. 1987) INTRODUCTION

Technical Notes 24G - The Contemporary Bearing Wall - Detailing [Dec. 1968] (Reissued Feb. 1987) INTRODUCTION Technical Notes 24G - The Contemporary Bearing Wall - Detailing [Dec. 1968] (Reissued Feb. 1987) INTRODUCTION The selection of a wall type and appropriate connection details is one of the most important

More information

Weatherproofing Masonry For Northern Climates

Weatherproofing Masonry For Northern Climates The enduring strength, beauty and performance of a brick wall assembly is critically dependant on three components: design, workmanship and materials. If even one of these factors has not been diligently

More information

What s Gray, Gets Hard, and Holds Up Your Home?

What s Gray, Gets Hard, and Holds Up Your Home? Concrete Foundation Association of North America 1 THE Resource for Contractors, Producers, Engineers and Suppliers in the Concrete Foundation Industry Mission Statement To unite, in common organization,

More information

Thermal Control in Buildings by John Straube (updated )

Thermal Control in Buildings by John Straube (updated ) building science.com 2006 Building Science Press All rights of reproduction in any form reserved. Building Science Digest 011 Thermal Control in Buildings 2006-11-02 by John Straube (updated 2011-12-12)

More information

The ECHO System The basement ventilated and drained insulation system

The ECHO System The basement ventilated and drained insulation system The ECHO System The basement ventilated and drained insulation system 1 Engineered by Indoor Air Technologies Inc Constructed by Licensed Contractors in Canada and the USA The ECHO System TM is made up

More information

Energy Efficiency. Understanding R-value, Mass Walls, Continuous Insulation and Air Tightness By Bautex Systems, LLC

Energy Efficiency. Understanding R-value, Mass Walls, Continuous Insulation and Air Tightness By Bautex Systems, LLC Energy Efficiency Understanding R-value, Mass Walls, Continuous Insulation and Air Tightness By Bautex Systems, LLC R-Value isn t the only variable that affects a building s Energy Efficiency. How to talk

More information

Evolution of Wall Design for Controlling Rain Penetration

Evolution of Wall Design for Controlling Rain Penetration Construction Technology Update No. 9 Evolution of Wall Design for Controlling Rain Penetration by G.A. Chown, W.C. Brown and G.F. Poirier The design of walls to control rain penetration has changed considerably

More information

AIR BARRIER SYSTEMS VAPOR-PERMEABLE AND NON-PERMEABLE. Sealed, Smart, and Sustainable WATERPROOFING & BUILDING PRODUCTS COMMERCIAL PRODUCT

AIR BARRIER SYSTEMS VAPOR-PERMEABLE AND NON-PERMEABLE. Sealed, Smart, and Sustainable WATERPROOFING & BUILDING PRODUCTS COMMERCIAL PRODUCT WATERPROOFING & BUILDING PRODUCTS COMMERCIAL PRODUCT VAPOR-PERMEABLE AND NON-PERMEABLE AIR BARRIER SYSTEMS Sealed, Smart, and Sustainable Environmentally friendly and ecologically sound Effective, efficient

More information

Condensation - Prevention and Control

Condensation - Prevention and Control TECHNICAL NOTES on Brick Construction 47 1850 Centennial Park Drive, Reston, Virginia 20191 www.gobrick.com 703-620-0010 June 2006 Condensation - Prevention and Control Abstract: This Technical Note describes

More information

FOOTINGS AND FOUNDATIONS

FOOTINGS AND FOUNDATIONS DHI_Book15_C01.qxd 28/05/2003 12:37 Page 3 I P A R T O N E FOOTINGS AND FOUNDATIONS We re going to talk about footings and foundations from a performance standpoint. We re looking to see whether they re

More information

New Approaches to Energy Efficiency & Green Building. Who is Icynene Inc.? World-Wide Distribution. The Icynene Insulation System

New Approaches to Energy Efficiency & Green Building. Who is Icynene Inc.? World-Wide Distribution. The Icynene Insulation System The Icynene Insulation System New Approaches to Energy Efficiency & Green Building Control of Air Leakage and Moisture Vapour Transmission Who is Icynene Inc.? Founded in November, 1986 in Toronto Canada

More information

Preventing Water Leakage through Construction Joints using SYNKOFLEX Preformed Compressible Waterstop

Preventing Water Leakage through Construction Joints using SYNKOFLEX Preformed Compressible Waterstop Preventing Water Leakage through Construction Joints using SYNKOFLEX Preformed Compressible Waterstop Introduction A typical problem in most Water Retaining Structures is the leakage of water through Construction

More information

How-to: Commissioning Design Reviews for the Building Envelope

How-to: Commissioning Design Reviews for the Building Envelope AABC Commissioning Group AIA Provider Number 50111116 How-to: Commissioning Design Reviews for the Building Envelope Course Number: CXENERGY1625 Stevan Vinci, BECxP, LEED AP, Morrison Hershfield Maurya

More information

Basement Board High Performance (HP) 70 and 100

Basement Board High Performance (HP) 70 and 100 Basement Board High Performance (HP) 70 and 100 Floor and Wall Insulation - Basements Basement Board HP is a closed cell expanded polystyrene (EPS) insulation board which makes it suitable for use below

More information

2006 Building Science Press All rights of reproduction in any form reserved.

2006 Building Science Press All rights of reproduction in any form reserved. building science.com 2006 Building Science Press All rights of reproduction in any form reserved. Building Science Digest 011 Thermal Control in Buildings 2006-11-07 by John Straube Abstract: Providing

More information

PLATON RUGGED, DIMPLED HIGH-DENSITY POLYETHYLENE (HDPE) MEMBRANE THAT KEEPS FOUNDATIONS AND FLOORING DRY ADVANCED TECHNOLOGY EASY INSTALLATION

PLATON RUGGED, DIMPLED HIGH-DENSITY POLYETHYLENE (HDPE) MEMBRANE THAT KEEPS FOUNDATIONS AND FLOORING DRY ADVANCED TECHNOLOGY EASY INSTALLATION DRAINAGE SOLUTIONS SINCE 1908 PLATON RUGGED, DIMPLED HIGH-DENSITY POLYETHYLENE (HDPE) MEMBRANE THAT KEEPS FOUNDATIONS AND FLOORING DRY ADVANCED TECHNOLOGY EASY INSTALLATION PROVEN PERFORMANCE ARMTEC.COM

More information

About Insulation & R Value - cmhc.ca

About Insulation & R Value - cmhc.ca About Insulation & R Value - cmhc.ca Insulating Your House While previous generations may have been content to live in drafty houses, most people now want comfortable warm houses. A healthy house today

More information

Incorporating Insulating Sheathing into the Design of the Thermal and Moisture Management System of the Building Enclosure

Incorporating Insulating Sheathing into the Design of the Thermal and Moisture Management System of the Building Enclosure Incorporating Insulating Sheathing into the Design of the Thermal and Moisture Management System of the Building Enclosure Peter Baker, Building Science Corporation ABSTRACT With rising utility cost, concerns

More information

Carpenter Level 2 Rev. September 2017

Carpenter Level 2 Rev. September 2017 Level 2 A5 Site Layout II Duration: 14 hours 7 hours 7 hours Upon completion of this unit the apprentice will demonstrate knowledge of site layout tools and equipment and their applications and procedures

More information

STUDY ON WETTING AND DRYING OF CLAY BRICK HAVING SURFACE COATINGS

STUDY ON WETTING AND DRYING OF CLAY BRICK HAVING SURFACE COATINGS 10 th Canadian Masonry Symposium, Banff, Alberta, June 8 12, 2005 STUDY ON WETTING AND DRYING OF CLAY BRICK HAVING SURFACE COATINGS P.J. Kelly Senior Product Quality Manager, Hanson Brick ABSTRACT This

More information

Rainscreen Description Manual

Rainscreen Description Manual Rainscreen Description Manual BUILDING ENVELOPE ENGINEERING 1058 Daley Street Edmonds, WA 98020 Phone: (425) 672-3900 Fax: (425) 712-8608 BEE-Engineers.com Page 2 of 15 TABLE OF CONTENTS History 3 Rainscreen

More information

Index. STP779-EB/Jul. 1982

Index. STP779-EB/Jul. 1982 STP779-EB/Jul. 1982 Index A Absorption of moisture (see Moisture absorption) Adsorption, 191 Capillary versus time, 197 Isotherms For glass fiber, 194, 195 For various materials, 196 Air leakage (exfiltration,

More information

building science.com Building Science Digest 103 Understanding Basements by Joseph Lstiburek

building science.com Building Science Digest 103 Understanding Basements by Joseph Lstiburek building science.com 2006 Building Science Press All rights of reproduction in any form reserved. Building Science Digest 103 Understanding Basements 2006-10-26 by Joseph Lstiburek Abstract: Buildings

More information

August 2008: Issue 1. Non - Residential New Build 4.5 Basements

August 2008: Issue 1. Non - Residential New Build 4.5 Basements Non - Residential New Build 4.5 Basements August 2008: Issue 1 Non-residential new build 4.0 Non-residential New Build Basements Contents Introduction find online page Solution optimiser and pathfinder

More information

Core Building Advances: Introduction to Sustainable Building & Building Science

Core Building Advances: Introduction to Sustainable Building & Building Science Core Building Advances: Introduction to Sustainable Building & Building Science Rob Howard & Mike Mongeon Habitat for Humanity International rhoward@habitat.org mmongeon@habitat.org Introductions Name

More information

Welcome to this continuing education seminar. This is the first of three parts of the Building Enclosure Fundamentals series.

Welcome to this continuing education seminar. This is the first of three parts of the Building Enclosure Fundamentals series. Welcome to this continuing education seminar. This is the first of three parts of the Building Enclosure Fundamentals series. 1 3 6 7 8 The primary reasons to build airtight buildings are to avoid drafts

More information

4. Insulation of external walls

4. Insulation of external walls 4. Insulation of external walls 4.1. Insulation on the internal side of the walls For both internal and external types of insulation the major advantages are the decrease in energy consumption as well

More information

SOLAR GREENHOUSES Calling a greenhouse solar is somewhat redundant, since all greenhouses are solar heated to some extent. The greenhouse itself

SOLAR GREENHOUSES Calling a greenhouse solar is somewhat redundant, since all greenhouses are solar heated to some extent. The greenhouse itself SOLAR GREENHOUSES Calling a greenhouse solar is somewhat redundant, since all greenhouses are solar heated to some extent. The greenhouse itself traps the heat each day, as anyone who has been inside a

More information

Building Science Control Layer Glossary. Façade Visible exterior face of a building, usually vertical or nearly so, but imprecisely used.

Building Science Control Layer Glossary. Façade Visible exterior face of a building, usually vertical or nearly so, but imprecisely used. It is far more important than often appreciated to use precise, unambiguous, clear definitions when describing aspects of buildings, building enclosures, and building science performance. The following

More information

Definition of Wall. A continuous, vertical structure Thin relatively to its length and height

Definition of Wall. A continuous, vertical structure Thin relatively to its length and height Walls & Partition Learning Objectives Briefly explain the functions & functional requirements of walls Differentiate and compare between load bearing and non-load bearing walls Briefly describe the characteristics,

More information

STAYFLEX CORROSION CONTROL AND THERMAL INSULATION SYSTEM

STAYFLEX CORROSION CONTROL AND THERMAL INSULATION SYSTEM STAYFLEX CORROSION CONTROL AND THERMAL INSULATION SYSTEM Installed in Pre-engineered Steel Buildings Provides Lowest Cost Construction Method for CORROSIVE AND WET Environments PREFERRED SOLUTIONS, INC.

More information

United States. Why You Should Insulate Foundations. There is a science to adding value.

United States. Why You Should Insulate Foundations. There is a science to adding value. United States R E S I D E N T I A L Why You Should Insulate Foundations. There is a science to adding value. Built On Science. STYROFOAM extruded polystyrene and polyisocyanurate insulations from Dow are

More information

Senior Design Project for UNO. Design of the International Studies Building: An Environmental Analysis

Senior Design Project for UNO. Design of the International Studies Building: An Environmental Analysis Senior Design Project for UNO Design of the International Studies Building: An Environmental Analysis Design Intent Implement Passive & Active design strategies in order to make the building: More Energy

More information

Total Parking Solutions: From Lowest or Basement Levels to Roof Top Decks

Total Parking Solutions: From Lowest or Basement Levels to Roof Top Decks Contact the Flooring Specialist +91 44 4017 6600 india@flowcrete.com Total Parking From Lowest or Basement Levels to Roof Top Decks Multi-storey car parks are unique buildings, one in which all elements

More information

Controlling Moisture.

Controlling Moisture. . Controlling Against Moisture Damage For Wall Sheathing...3 Sweaty Vents...4 Controlling Condensation In The Home...4 Controlling Against Moisture Damage For Wall Sheathing Moisture can cause many structural

More information

Experimental Study to Evaluate the Performance of Iraqi Passive House in Summer Season

Experimental Study to Evaluate the Performance of Iraqi Passive House in Summer Season Journal of Energy and Power Engineering 9 (2015) 386-392 doi: 10.17265/1934-8975/2015.04.008 D DAVID PUBLISHING Experimental Study to Evaluate the Performance of Iraqi Passive House in Summer Season Ghanim

More information

Insulated Metal Panel (IMP) Systems

Insulated Metal Panel (IMP) Systems METL-SPAN Joseph Lstiburek, Ph.D., P.Eng. November, 2015 Table of Contents 1. Physics of Building Enclosures... 4 2. Physics of Insulated Metal Panels... 12 3. Joint Design... 19 4. Thermal Bridging...

More information

National Research Council Canada. Conseil national de recherches Canada. Canada

National Research Council Canada. Conseil national de recherches Canada. Canada National Research Council Canada Conseil national de recherches Canada In-situ Performance Evaluation of Exterior Insulation Basement System (EIBS) Spray Polyurethane Foam Summary Report M.C. Swinton,

More information

A Design Review of Waterproofing Codes

A Design Review of Waterproofing Codes A Design Review of Waterproofing Codes Section 1807 of Chapter 18 of the International Building Code addresses waterproofing under the section title of Dampproofing and Waterproofing. The section defines

More information

Frost Damage in Roof Tiles in Relatively Warm Areas in Japan

Frost Damage in Roof Tiles in Relatively Warm Areas in Japan Frost Damage in Roof Tiles in Relatively Warm Areas in Japan Water Absorption and Freezing-Thawing Experiments Chiemi IBA Hokkaido Research Organization, Japan Shuichi HOKOI Kyoto University, Japan Introduction

More information

Contents. 1.1 Introduction 1

Contents. 1.1 Introduction 1 Contents PREFACE 1 ANCIENT MASONRY 1 1.1 Introduction 1 1.2 History of Masonry Materials 1 1.2.1 Stone 2 1.2.2 Clay Units 2 1.2.3 Calcium Silicate Units 4 1.2.4 Concrete Masonry Units 4 1.2.5 Mortars 5

More information

CRAWL-SPACE CONSTRUCTION

CRAWL-SPACE CONSTRUCTION CRAWL-SPACE CONSTRUCTION Many basementless houses are built over a crawl space- that is, the grade-level floor is over an excavation which is deep enough to allow a man to gain access to the underfloor

More information

MasterFlow 980 (Formerly known as Masterflow 980 M)

MasterFlow 980 (Formerly known as Masterflow 980 M) High strength, shrinkage compensated cementitious micro concrete DESCRIPTION OF PRODUCT MasterFlow 980 is a ready-to-use product in powder form, which requires only the on-site addition of water to produce

More information

Emperor Penguins and Efficient Buildings. Resisting frigid temps with thermal breaks.

Emperor Penguins and Efficient Buildings. Resisting frigid temps with thermal breaks. Emperor Penguins and Efficient Buildings. Resisting frigid temps with thermal breaks. March 2017 Brent Chancellor, PhD, PE Product Engineer Schöck North America Thermal Breaks Prevent Heat Loss Through

More information

CHAPTER 1: OVERVIEW OF ENERGY EFFICIENT CONSTRUCTION

CHAPTER 1: OVERVIEW OF ENERGY EFFICIENT CONSTRUCTION Chapter 1: Overview of Energy Efficient Construction 1 CHAPTER 1: OVERVIEW OF ENERGY EFFICIENT CONSTRUCTION Chapter 1 is a quick reference guide that discusses the key components and features of energy

More information

CEN/TC 89 - Thermal performance of buildings and building components

CEN/TC 89 - Thermal performance of buildings and building components CEN/TC 89 - Thermal performance of buildings and building components Standard reference EN 1934:1998 EN 1946-1:1999 EN 1946-2:1999 EN 1946-3:1999 EN 1946-4:2000 EN 1946-5:2000 6946:2007 7345:1995 8497:1996

More information

MEMBRANE WATER PROOFING. Our Services: Below ground waterproofing, Above-ground waterproofing, Wet Areas Waterproofing, Joint Sealants.

MEMBRANE WATER PROOFING. Our Services: Below ground waterproofing, Above-ground waterproofing, Wet Areas Waterproofing, Joint Sealants. WATER PROOFING MEMBRANE s vast experience in providing constructive solutions to many famous building structures around the world hasbeen built on a broad portfolio of products. Our Services: Below ground

More information

Fabrications, Safety & Lighting Solutions. Product Data Sheet. Kingspan Day-Lite Klick KS500 DLKK

Fabrications, Safety & Lighting Solutions. Product Data Sheet. Kingspan Day-Lite Klick KS500 DLKK Fabrications, Safety & Lighting Solutions Kingspan Day-Lite KS500 DLKK Applications Kingspan Day-Lite is a secret-fix wall light system typically suited for vertical applications. Featuring an innovative

More information

LATICRETE and Moisture Vapour Emission Rate, Relative Humidity and Moisture Testing of Concrete

LATICRETE and Moisture Vapour Emission Rate, Relative Humidity and Moisture Testing of Concrete LATICRETE and Moisture Vapour Emission Rate, Relative Humidity and Moisture Testing of Concrete TDS-1166 Materials used in tile and stone installation applications can be affected by moisture during the

More information

The Disclaimer located on the reverse side of the title page of the OAA Rain Penetration Practice Guide applies to each section of the Guide.

The Disclaimer located on the reverse side of the title page of the OAA Rain Penetration Practice Guide applies to each section of the Guide. Note: This document has been divided into several sections in order to suit the limitations of the website. The Disclaimer located on the reverse side of the title page of the OAA Rain Penetration Practice

More information

Moisture Considerations for Insulated Building Assemblies

Moisture Considerations for Insulated Building Assemblies PHRC Webinar Series Tuesday, November 10, 2015 @ 1pm Description Moisture Considerations for Insulated Building Assemblies Brian Wolfgang Housing Systems Specialist One critical design consideration in

More information

4 EXTREME FOUNDATION PANELS

4 EXTREME FOUNDATION PANELS 4 EXTREME FOUNDATION PANELS For House Crawl Space On Concrete Footings 1. The type of soil is a factor in determining foundation construction details such as footing design, backfill, and drainage provisions.

More information

Waterproofing and Types of Drains

Waterproofing and Types of Drains Waterproofing and Types of Drains 4 PVC Downspout Burial w/ Y Fitting for Future Clean-out Yard Drain Box 12 Drain Box 12885 Old Frederick Road Sykesville, MD 21784 Office 410-442-2445 Fax 410-489-4312

More information

Flexible Vapor Control Solves Moisture Problems of Building Assemblies - Smart Retarder to Replace the Conventional PE-Film

Flexible Vapor Control Solves Moisture Problems of Building Assemblies - Smart Retarder to Replace the Conventional PE-Film Flexible Vapor Control Solves Moisture Problems of Building Assemblies - Smart Retarder to Replace the Conventional PE-Film HARTWIG M. KÜNZEL Fraunhofer-Institute of Building Physics (Director: Prof. Dr.-Ing.

More information

Low-cost Construction for High-energy Savings. Brian J. Wimmer Construction Manager Rochester Area Habitat for Humanity

Low-cost Construction for High-energy Savings. Brian J. Wimmer Construction Manager Rochester Area Habitat for Humanity Low-cost Construction for High-energy Savings Brian J. Wimmer Construction Manager Rochester Area Habitat for Humanity construction@rahh.org Objectives: 1. Control air & moisture in high-performance, low-cost

More information

June Non - Residential Refurbishment 5.5 Basements

June Non - Residential Refurbishment 5.5 Basements June 2010 Non - Residential Refurbishment 5.5 Basements Non-residential refurbishment 5.0 Non-residential Refurbishment Basements Contents Introduction find online page Solution optimiser and pathfinder

More information

BUILDING ENVELOPE PRODUCTS PROVIDING A FULL BUILDING ENVELOPE SYSTEM. Control Moisture Movement with Our Patented Technology

BUILDING ENVELOPE PRODUCTS PROVIDING A FULL BUILDING ENVELOPE SYSTEM. Control Moisture Movement with Our Patented Technology BUILDING ENVELOPE PRODUCTS PROVIDING A FULL BUILDING ENVELOPE SYSTEM Control Moisture Movement with Our Patented Technology Whatever Your Needs WE HAVE THE SOLUTION Methods of controlling moisture in building

More information

Wall Selection Guide Section 1.1

Wall Selection Guide Section 1.1 Page 1 MASONRY WALL TYPES Masonry is the most enduring of all building materials, as exemplified by the oldest and most revered architecture from around the world. The exceptional structural integrity

More information

Module number 3 provides an on-line, self-paced training seminar on chapter 4, foundations and chapter 5, floors from the residential code of ohio.

Module number 3 provides an on-line, self-paced training seminar on chapter 4, foundations and chapter 5, floors from the residential code of ohio. Module number 3 provides an on-line, self-paced training seminar on chapter 4, foundations and chapter 5, floors from the residential code of ohio. 1 This chapter sets forth the prescriptive requirements

More information

Healthy, Durable, Low Energy Buildings: Thermal: High R. Thermal bridges. Fundamentals, techniques, and pitfalls

Healthy, Durable, Low Energy Buildings: Thermal: High R. Thermal bridges. Fundamentals, techniques, and pitfalls Dr John Straube, P.Eng. Associate Professor, University of Waterloo Principal, Building Science Corporation Healthy, Durable, Low Energy Buildings: Fundamentals, techniques, and pitfalls Thermal: High

More information

Improve Energy Efficiency and Moisture Performance of Foundations

Improve Energy Efficiency and Moisture Performance of Foundations Escalating home energy costs and changing energy codes are two big challenges facing builders today. Dow Building Solutions can help you meet those challenges and differentiate your business by building

More information

Residential Concrete 101

Residential Concrete 101 PHRC Webinar Series Tuesday, December 13th @ 1pm Residential Concrete 101 Christopher Hine Pennsylvania Housing Research Center 219 Sackett Building University Park, PA 16802 P: 814 865 2341 phrc@psu.edu

More information

10 TIPS FOR FALL AND WINTER FACILITY MAINTENANCE

10 TIPS FOR FALL AND WINTER FACILITY MAINTENANCE 10 TIPS FOR FALL AND WINTER FACILITY MAINTENANCE With the fall season upon us, we would like to share some tips for year-end facilities maintenance. 1. REDUCE YOUR TEMPERATURE SET POINTS You can reduce

More information

PLANNING FOR DURABILITY IN BUILDING PROJECTS: STRATEGIES AND TECHNICAL RECOMMENDATIONS ACCORDING TO LEED CANADA

PLANNING FOR DURABILITY IN BUILDING PROJECTS: STRATEGIES AND TECHNICAL RECOMMENDATIONS ACCORDING TO LEED CANADA PLANNING FOR DURABILITY IN BUILDING PROJECTS: STRATEGIES AND TECHNICAL RECOMMENDATIONS ACCORDING TO LEED CANADA Silverio HERNÁNDEZ-MORENO Autonomous University of the State of Mexico, Toluca, Mexico silverhm2002@yahoo.com.mx

More information

BELOW GRADE ASSEMBLIES AND RIGID INSULATION

BELOW GRADE ASSEMBLIES AND RIGID INSULATION BELOW GRADE ASSEMBLIES AND RIGID INSULATION 2010 Atlas Roofing Corporation. Atlas EPS is a division of Atlas Roofing. ThermalStar is a registered trademark and X-Grade is a trademark of Atlas Roofing Corporation.

More information

June Residential Refurbishment Basements

June Residential Refurbishment Basements June 2010 Residential Refurbishment 3.5.1 Basements Residential refurbishment 3.0 Residential Refurbishment Basements Contents Introduction find online page Solution optimiser and pathfinder 293 Design

More information

U.S. EDITION RESIDENTIAL CONSTRUCTION DETAILS SAMPLE. A visual guide to construction detailing. Emma Walshaw

U.S. EDITION RESIDENTIAL CONSTRUCTION DETAILS SAMPLE. A visual guide to construction detailing. Emma Walshaw RESIDENTIAL CONSTRUCTION DETAILS U.S. EDITION A visual guide to construction detailing Emma Walshaw Contents INTRODUCTION 4 PRINCIPLES OF CONSTRUCTION DETAILING 6 FOUNDATIONS 9 PRINCIPLES OF FOUNDATION

More information

Topic 1 - Properties of Concrete. 1. Quick Revision

Topic 1 - Properties of Concrete. 1. Quick Revision Topic 1 - Properties of Concrete 1. Quick Revision 1.1 Constituent Materials of concrete Concrete is composed mainly of three materials, namely, cement, water and aggregate, and sometimes additional material,

More information

RADON ABATEMENT FROM THE GROUND UP

RADON ABATEMENT FROM THE GROUND UP RADON ABATEMENT FROM THE GROUND UP The solution for a dry, comfortable, and durable basement! CLOSED-CELL 2018 Demilec, 3315 E. Division St., Arlington, TX 76011 Phone: 817.640.4900 Fax: 817.633.2000 Info@Demilec.com

More information

SECTION FLUID-APPLIED WATERPROOFING

SECTION FLUID-APPLIED WATERPROOFING SECTION 07140 FLUID-APPLIED WATERPROOFING PART 1 GENERAL 1.1 SUMMARY A. Section includes fluid applied rubberized asphalt and/or elastomeric membrane waterproofing; and surface dusting and/or protective

More information

Armatherm Structural Thermal Bridging Solutions

Armatherm Structural Thermal Bridging Solutions Armatherm Structural Thermal Bridging Solutions Minimising energy loss and improving building envelope performance www.armatherm.co.uk info@armatherm.com +44 (0) 1274 591 115 Armatherm is one of the leading

More information

7. MATERIALS AND TECHNICAL INVESTIGATION

7. MATERIALS AND TECHNICAL INVESTIGATION 67 7. MATERIALS AND TECHNICAL INVESTIGATION Materials were chosen to provide minimal long-term maintenance. Hardwearing materials on ground floor levels were chosen to withstand the wear and tear of children

More information