Project No: Pakenham Branch Library, Pakenham, Ontario Section January, 2017 Page 1 of 7
|
|
- Madeline Stafford
- 5 years ago
- Views:
Transcription
1 January, 2017 Page 1 of 7 1 GENERAL 1.01 RELATED SECTIONS.1 Section Submittal Procedures.2 Section Closeout Submittals.3 Section Sealants..4 Section Glazing REFERENCES.1 American Architectural Manufacturers Association (AAMA)..1 AAMA CW-DG-1-96, Aluminum Curtain Wall Design Guide Manual..2 AAMA CW-10-97, Care and Handling of Architectural Aluminum From Shop to Site..3 AAMA , Voluntary Specification Performance Requirements and Test Procedures for Superior Performance Organic Coatings on Aluminum Extrusions and Panels..2 American Society for Testing and Materials International, (ASTM)..1 ASTM B , Specification for Aluminum and Aluminum-Alloy Sheet and Plate..2 ASTM B , Specification for Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes..3 ASTM E (2012), Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen..4 ASTM E (2010), Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights, and Curtain Walls, by Uniform Static Air Pressure Difference..5 ASTM E (2009), Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls, by Uniform Static Air Pressure Difference..3 Canadian Standards Association (CSA International)..1 CSA-G40.20/G (R2009), General Requirements for Rolled or Welded Structural Quality Steel/Structural Quality Steels..2 CAN/CSA-G164-M92 (R2003), Hot Dip Galvanizing of Irregularly Shaped Articles..3 CSA-S136-01, North American Specification for the Design of Cold-Formed Steel Structural Members..4 CAN/CSA-S157-05/S (R2010)- Strength Design in Aluminum..5 CSA W59.2-M1991 (R2008), Welded Aluminum Construction..6 CAN/CSA-A /A Fenestration energy performance.7 CSA A440-08, North American Fenestration Standard/Specification for Windows, Doors, and Skylights PERFORMANCE REQUIREMENTS.1 Windows: Performance criteria, to CAN A440:
2 January, 2017 Page 2 of SUBMITTALS.1 Air infiltration = A3.2 Water infiltration = B7.3 Wind load resistance: C5.4 Thermal resistance.1 Framing: U Entrance Doors: U Frame condensation resistance I = 60.1 Provide submittals in accordance with Section Submittal Procedures..2 Provide component dimensions, describe components within assembly, anchorage and fasteners, glass and infill, internal drainage details and water flow diagrams..3 Shop drawings:.1 Indicate system dimensions, framed opening requirements and tolerances, adjacent construction, anchor details anticipated deflection under load, affected related Work, weep drainage network, expansion and contraction joint location and details, and field welding required..4 Submit two samples 75 x 75 mm in size illustrating prefinished aluminum surface, finish, colour and texture..5 Design data:.1 Provide framing member structural and physical characteristics, calculations, dimensional limitations, special installation requirements..6 Test Reports.1 Submit engineering data, supporting data and results of tests by an independent laboratory for: Air Tightness, Water tightness, Wind Load Resistance, Forced Entry Resistance, Ease of Operation, Sash Strength, and Screen Strength DELIVERY, STORAGE, AND HANDLING.1 Deliver, store, handle and protect materials in accordance with manufacturer s printed instructions..2 Protect prefinished aluminum surfaces with wrapping. Do not use adhesive papers or sprayed coatings which bond when exposed to sunlight or weather.
3 January, 2017 Page 3 of 7 2 PRODUCTS 2.01 MATERIALS.1 Extruded aluminum: ASTM B Sheet aluminum: ASTM B Anchors: 3-way adjustable hot-dip galvanized cast iron..4 Fasteners: galvanized steel.5 Vision glass units: in accordance with Section Glazing.6 Sealant: in accordance with Section Sealants..7 Face Dimensions (nominal): 2.8 Operation: Awning, unless otherwise noted on drawings..1 Forced Entry: To CSA A440.9 Sash Locks: Sequentially locking multi-point type with single handle actuator.10 Screens: Extruded aluminum frame with VIEWS (Virtually invisible screen wire.).11 Reinforcement: Galvanized carbon steel.1 Structural Shapes, Plates and Bars: ASTM A 36.2 Cold Rolled Sheet and Strip: ASTM A Hot Rolled Sheet and Strip: ASTM A Weatherseals:.1 Black polymer (EPDM) replaceable weatherseals:.1 Shapes, designs, and thickness as needed to satisfy performance requirements..2 Weatherseals shall be provided in continuous lengths, butted firm to ends of races and to each other when in the same planes..13 Glazing:.1 Glazing to Section Glazing.14 Fasteners:.1 Corrosion-resistant MATERIALS 1. Operable Window.1 Accepted Manufacturer: Kawneer Company Inc..1 GLASSvent Windows - Project Out windows..2 (71.4 mm) system depth (1" 2.Infill).3 P-HC70 Project-Out Window
4 January, 2017 Page 4 of 7.4 Performance criteria as specified in 1.03 Performance Requirements.2 Accepted Manufacturer: Alumicor Inc..1 Univent 1350 double glazed top hung, project out, vent..2 Performance criteria as specified in 1.03 Performance Requirements 2.03 FABRICATION 2. Materials: to CSA-A440/A440.1 supplemented as follows: 3. Type: Awning, as illustrated on drawings. 4. Glazing: in accordance with Section : 5. Sash and frame: thermally broken aluminum. Sash / glazing placement: face of glazing to be nominal 50mm from exterior face of window frame profile. 6. Screens: to CAN/CGSB Insect screening mesh: count 18 x 14.2 Screen frames: aluminum colour to match window frames. Mount screen frames for interior replacement. 7. Accessories: Locking cam handles (3) per window. 8. Tamperproof limit stop to limit window opening to maximum 100mm. 9. Flashings: 2 mm thick aluminum, finish to match mullion sections where exposed, secured with concealed fastening method..1 Verify dimensions of each window on site before fabrication..2 Miter cut and fusion weld (i.e. thermally weld) all frame and sash corners..3 Complete fabrication, assembly, finishing, hardware application, and other work for each individual window unit before shipment to Site. Field assembly to connect two or more mulled windows is permitted..4 Provide baffled drainage holes to drain moisture to exterior..5 Window construction, edge clearance and placement of installation fasteners shall allow for expansion and contraction per the specified system performance requirements..6 Provisions shall be made in framing, including sash, for minimum glass edge clearance, nominal edge cover, and nominal pocket width, in compliance with GANA Glazing Manual, for thickness and type glass needed..7 Framing shall be provided with reinforcing members as necessary. Provide aluminum or steel members as needed to reinforce frame and/or sash components as
5 January, 2017 Page 5 of 7 recommended by window manufacturer to develop needed strength of assembly..8 Framing members shall be structurally adequate to carry dead load, accommodate thermal movement, and resist wind loads..9 Flashing and other materials used around window opening shall be corrosion resistant, non-staining, non-bleeding, and compatible with adjoining materials.10 Pre-finished galvanized metal colours will be selected from standard range of colours FINISHES.1 Interior finish coatings: conform to AAMA 2603 designation..1 Interior aluminum surfaces: prepare surfaces with appropriate pre-treatment, primer coat and wet coat acrylic coating topcoat..2 Colour: white.2 Exterior finish coatings: conform to AAMA 2605 designation..1 Exterior aluminum surfaces: prepare surfaces with appropriate pre-treatment, primer coat and thermoset, minimum 70% fluorocarbon coating topcoat..2 Colour: PPG, UC102662F, Medium Gray..3 Touch-up primer for galvanized steel surfaces: SSPC 20 Paint zinc rich..4 Concealed steel items: galvanized in accordance with ASTM A 123 to 380 gm/m². 3 EXECUTION 3.01 EXAMINATION.1 Verify dimensions, tolerances, and method of attachment with other work..2 Verify wall openings and adjoining air barrier and vapour retarder materials are ready to receive work of this section WINDOW INSTALLATION.1 Install in accordance with CSA-A440/A440.1 and manufacturer s printed instructions..2 Comply with manufacturer s instructions and recommendations for installation of work..3 Do not erect warped, bowed, deformed or otherwise damaged or defaced members. Replace materials that are damaged during installation as directed..4 Set units level, plumb, and true to line, with uniform joints. Support units on shims and secure in place by approved installation anchors/fasteners that properly engage into to supporting structure..1 Erection Tolerances:.1 Variations From Plumb: ±1/8 maximum in window height..2 Variations from Level: ±1/16 maximum in 10 run, non-cumulative..5 Pack fibrous insulation in shim spaces at perimeter of assembly to maintain continuity of
6 January, 2017 Page 6 of 7 thermal barrier SILL INSTALLATION.1 Install metal sills with uniform wash to exterior, level in length, straight in alignment with plumb upstands and faces. Use one piece lengths at each location..2 Cut sills 50 mm longer than window opening..3 Secure sills in place with anchoring devices located at ends and evenly spaced 600 mm on centre in between..4 Maintain 6 to 9 mm space between butt ends of continuous sills. For sills over 1200 mm in length, maintain 3 to 6 mm space at each end FIELD QUALITY CONTROL.1 After completion of installation and nominal curing of sealant and glazing compounds, but before installation of exterior cladding and finishes, test 10% of installed windows (but not less than 4 windows) for water leaks in compliance with CSA-A440. Testing area to include: window sill, jamb(s) and head; completed window buck assembly with all membraning on exterior correctly lapped onto exterior sheathing; all pertinent sealants complete with backer rods; interior air/vapour membranes and any additional components which comprise the air and moisture barriers as directed by the consultant..2 Testing will be carried out at locations of window installation as selected by building envelope consultant. Failure of tested location will require additional testing to the failed location after repairs have been completed in addition to the testing of new locations. On-site field testing will continue until all tested areas meet the performance criteria and to the satisfaction of the independent building envelope consultant. Testing repairs and retesting are at the expense of the window wall manufacturer and/or contractor, and shall not be at the expense of the owner..3 In-situ performance requirements.1 Windows: Performance criteria, to CAN A440:.1 Air infiltration = A3.2 Water infiltration = B7.3 Wind load resistance: C5.4 Thermal resistance = U value 0.43 in accordance with AAMA Frame condensation resistance I = CAULKING.1 Seal joints between windows and window sills with sealant. Bed sill expansion joint cover plates and drip deflectors in bedding compound. Caulk between sill upstand and window-frame. Caulk butt joints in continuous sills..2 Apply sealant in accordance with Section Joint Sealing 3.06 CLEANING.1 Clean completed system in compliance with manufacturer s recommendations, inside
7 January, 2017 Page 7 of 7 and out, promptly after erection and installation of glass and sealants. Remove excess glazing and joint sealants, dirt, and other substances from finished surfaces promptly after erection..2 Remove protective material from prefinished surfaces..3 Wash down exposed surfaces using a solution of mild detergent in warm water applied with soft, clean wiping cloths. Take care to remove dirt from corners. Wipe surfaces clean..4 Remove excess sealant by moderate use of mineral spirits, or other solvent acceptable to sealant manufacturer PROTECTION.1 Institute protective measures and other precautions needed to assure Work will be without damage or deterioration, other than normal weathering, at time of acceptance. END OF SECTION
Tender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Extruded aluminum windows with fixed sash..2 Factory glazed..3 Perimeter sealant. 1.2 RELATED SECTIONS.1 Section 05500 - Metal Fabrications.2
More informationSECTION ALUMINUM-FRAMED HIGH PERFORMANCE THERMAL ENTRANCE DOORS
PART 1 GENERAL SECTION 08 1116 ALUMINUM-FRAMED HIGH PERFORMANCE THERMAL ENTRANCE DOORS 1.01 SECTION INCLUDES A. Aluminum-framed storefront, with vision glass. B. Infill panels of glass. C. Aluminum doors
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS 1. PART 1 GENERAL 1.1 WORK INCLUDED: 1. Provide labor, material, equipment and services to furnish and install aluminum windows shown on drawings and specified herein. Window
More informationA. Section includes extruded aluminum windows with operating sash, operating hardware, and insect screens.
SECTION 08 51 13 - Page 1 PART 1 GENERAL 1.1 SUMMARY A. Section includes extruded aluminum windows with operating sash, operating hardware, and insect screens. B. Related Sections: 1. Section 07 92 00
More informationSECTION FOLDING ALUMINUM FRAMED WALL SYSTEM
SECTION 08417 FOLDING ALUMINUM FRAMED WALL SYSTEM PART 1 GENERAL 1.1 SUMMARY A. Section includes: 1. Folding aluminum framed door system. 2. Door hardware. 3. Glass. 1.2 SYSTEM DESCRIPTION A. Aluminum-framed
More information.1 Section Joint Sealants: Perimeter sealant and back-up materials.
Page 1 Part 1 GENERAL 1.1 SECTION INCLUDES.1 Aluminum windows..2 Glazing..3 Operating hardware and insect screens..4 Perimeter sealant. 1.2 RELATED SECTIONS.1 Section 07 92 00 - Joint Sealants: Perimeter
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 4113 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Aluminum entrance doors and frames. 2. Glass infill panels. 3. Door hardware. B. Related Sections:
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Cast
More informationSECTION STAINLESS STEEL WALL PANELS
SECTION 07400 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Dry joint, Rainscreen stainless steel wall panel system. 2. Accessories including attachments, clips, sub girts, shims, and fasteners 3.
More informationCentral Dartmouth Section Exterior Envelope Renovations METAL-CLAD WOOD DOORS Page 1 of 5 Dartmouth, NS
Exterior Envelope Renovations METAL-CLAD WOOD DOORS Page 1 of 5 Part 1 General 1. RELATED SECTIONS 1. Section 07 92 10 Joint Sealing 2. Section 08 71 00 Door Hardware 2. REFERENCES 1. American Society
More informationMPG Series 2250T Thermally Broken Aluminum Window
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2250T Thermally Broken Aluminum Window PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows complete with hardware
More informationPART 1 / GENERAL SECTION ALUMINUM PLATE PANEL SYSTEM. ALPLY Insulated Panels. Alply TECH WALL Aluminum Plate System 2002
SECTION 07 42 13 ALUMINUM PLATE PANEL SYSTEM ALPLY Insulated Panels Alply TECH WALL Aluminum Plate System 2002 PART 1 / GENERAL 1.1 SYSTEM DESCRIPTION A. Preformed Aluminum Plate System for Screen wall
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 08 51 69.11 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More informationNorth Hanover Township School District North Hanover Township, New Jersey
SECTION 084413 - GLAZED ALUMINUM CURTAIN WALLS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationTRUMAN STATE UNIVERSITY GREENWOOD SCHOOL WINDOW REPLACEMENT
SECTION 085200 - WOOD WINDOWS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationWESTECK WINDOWS and DOORS
WESTECK WINDOWS and DOORS SECTION 08565 VINYL (PVC) PATIO DOOR GENERAL Supply PVC patio sliding doors as per approved Shop Drawings. PART 1 1.1 SECTION INCLUDES A. Patio sliding doors 1.2 RELATED SECTIONS
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 08 51 69.11 ALUMINUM STORM WINDOWS SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. 2. Also delete any other item or paragraph not applicable
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 08 - OPENINGS. A. This Section includes fixed and operable aluminum-framed windows.
SECTION 085113 - ALUMINUM WINDOWS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes fixed and operable aluminum-framed windows. 1.2 PERFORMANCE REQUIREMENTS A. General: Provide aluminum windows capable
More informationSILVER LINE BUILDING PRODUCTS. Series 1700 Heavy Commercial Aluminum Double Hung. HC65 48 x84 / HC50 60 x96 Replacement Window
DIVISION 08 / SECTION 08505 METAL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: GENERAL Series 1700 Heavy Commercial Aluminum Double Hung 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE
More informationSECTION METAL FRAMED SKYLIGHT. A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system.
SECTION 08625 METAL FRAMED SKYLIGHT PART 1 GENERAL 1.01 SECTION INCLUDES: A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system. B. Fabrication
More informationFL200 13/4 x41/2 GUIDE SPECIFICATION. Non-Thermal Storefront
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide
More informationCOVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY)
COVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (DOOR ASSEMBLY)
More informationCardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS
Cardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide specification has been developed using
More informationSignature Series 5 Lap SECTION ALUMINUM WINDOWS
Signature Series 5 Lap SECTION 08 51 13 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Documents: Conditions of the Contract, Division 1 - General Requirements, and Drawings apply to Work of this
More information[Project Name] Section [ ]
Page 1 PART 1 - GENERAL 1.1 SECTION INCLUDES 1.1.1 Design, labor, products, equipment and services necessary for interior/exterior Aluminum Facade System (AFS) work, in accordance with the Contract Documents.
More informationSILVER LINE BUILDING PRODUCTS
DIVISION 08 / SECTION 08560, VINYL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: 2200/2300/2600 Vinyl Single Hung Windows R50/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2.
More informationSECTION DETAILS (MECHANICALLY ASSEMBLY)
COVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (DOOR ASSEMBLY)
More informationPRODUCT SPECIFICATION SERIES 5000T PUNCHED WINDOW THERMALLY BROKEN ALUMINUM CASEMENT/AWNING/ FIXED WINDOW
08 51 13 ALUMINUM WINDOWS PART 1 - GENERAL A high-quality thermally broken 3 ½ aluminum window designed for residential low, mid and high rise construction. 1.1 SUMMARY A. Section Includes: Aluminum Windows:
More informationSeries 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
More informationSECTION TRANSLUCENT PANEL SYSTEM
SECTION 084523 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this
More informationSpecification Section Storefront Systems has been revised. Omit previously issued Storefront section.
December 28, 2018 ADDENDUM NO. 2 To: Re: Bidders Corey Pitts, NewQuest Properties This Addendum forms a part of the contract documents identified above. Acknowledge the receipt of this Addendum on the
More informationA. Section includes conventionally glazed aluminum curtain walls installed as stick assemblies.
SECTION 084413 GLAZED ALUMINUM CURTAIN WALLS PART 1 - GENERAL 1.1 SUMMARY A. Section includes conventionally glazed aluminum curtain walls installed as stick assemblies. 1.2 PERFORMANCE REQUIREMENTS A.
More informationSECTION COMPOSITE WALL PANELS PART 1 GENERAL 1.01 SECTION INCLUDES
SECTION 07 4243 - PART 1 GENERAL 1.01 SECTION INCLUDES A. Composite wall panel system consisting of aluminum-faced composite panels in a rainscreen application as part of the assembly described below.
More informationPROJECT LOCATION SECTION COPPER METAL PLATE WALL PANELS
SECTION 07 4213.25 PART 1- GENERAL 1.01 SECTION INCLUDES A. Copper metal plate wall panels. 1.02 RELATED REQUIREMENTS A. Section 05 4000 Cold-Formed Metal Framing: Wall panel substrates support framing.
More informationUnited Window & Door - Series 5500 New Construction Double Hung Windows Specifications
United Window & Door - Series 5500 New Construction Double Hung Windows Specifications Part 1 GENERAL 1.01 INCLUSIONS 1. All windows as called for in this specification will be furnished with all necessary
More informationSECTION METAL WALL PANEL SYSTEM
CSI Format for Metal Wall Panel System Specification SECTION 07410 METAL WALL PANEL SYSTEM PART 1 GENERAL 1.1 SECTION INCLUDES A. Exterior Metal Plate Wall Panels B. Substructure and Framing C. Structural
More informationMARLIN WINDOWS, INC 3500 HC SERIES 3 3 8" SLIDING WINDOW PAGE 1
PAGE 1 SPECIFICATIONS GENERAL Sliding windows shall be Marlin series #3500-HC (thermally improved) as manufactured by Marlin windows, and shall conform to ANSI/AAMA 101-88 HS-HC40. Series #3500 shall have
More informationMPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows
More informationSERIES SA30 STEEL/ALUMINUM FIXED DETENTION WINDOWS SECTION 08651
SERIES SA30 STEEL/ALUMINUM FIXED DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows as
More informationSECTION VINYL (PVC) WINDOWS
SECTION 085313 VINYL (PVC) WINDOWS SERIES 3000/3900 NEW CONSTRUCTION DOUBLE HUNG PART 1 GENERAL 1.01 SECTION INCLUDES A. All windows of the types and sizes called for in this specification shall be furnished
More informationFIXED SERIES 6200 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4. Glazing Thickness (Maximum): 1
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com FIXED SERIES 6200 AAMA/WDMA/CSA 101/I.S.2/A440-08
More informationSeries 2900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 2900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
More informationWESTECK WINDOWS and DOORS
WESTECK WINDOWS and DOORS SECTION 08565 VINYL (PVC) WINDOWS HORIZONTAL SLIDING VERTICAL SLIDING FIXED GENERAL Supply PVC windows as per approved Shop Drawings. PART 1 1.1 SECTION INCLUDES A. Horizontal
More informationPRODUCT SPECIFICATION UNITIZED CURTAIN WALL THERMALLY BROKEN ALUMINUM AWNING/ FIXED WINDOW
08 44 13 GLAZED UNITIZED ALUMINUM CURTAIN WALL PART 1 - GENERAL A high-quality thermally broken aluminum unitized curtain wall system. The glass will be captured at the head, sill and stack joint locations.
More informationPRODUCT SPECIFICATION SERIES 4500T THERMALLY BROKEN ALUMINUM SLIDING BALCONY DOOR
08 2 1 SLIDING ALUMINUM FRAMED GLASS DOOR PART 1 - GENERAL A high-quality thermally broken aluminum balcony sliding door designed for residential high rise construction. 1.1 SUMMARY A. Section Includes:
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 - GENERAL 1.01 SUMMARY A. Section includes: 1. Storefront systems and aluminum framed glass doors. 2. Hardware, fasteners, accessories, filler pieces, etc., required
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 GENERAL 1.1 SECTION INCLUDES A. Projected windows. B. Fixed windows. 1.2 RELATED SECTIONS A. Section 07900: Joint Sealers. B. Section 08400: Entrances and Storefronts.
More informationCorium Brick Rainscreen System Specifications
CORIUM BRICK RAINSCREEN SYSTEM PART 1 - GENERAL 1.1 SUMMARY A. Work Included: The Work of this Section shall include but not be limited to the following: 1. Corium brick plates 2. Galvanized and coated
More informationVELUX America Inc. SPECIFICATION FOR MODEL QPF SELF-FLASHED FIXED SKYLIGHT SECTION UNIT SKYLIGHTS
SECTION 08620 UNIT SKYLIGHTS PART 1 GENERAL 1.01 SECTION INCLUDES A. Performance and product component information for VELUX QPF selfflashed fixed skylight. B. Unit skylight mounted directly to roof decking.
More informationA. Pre-Installation Conference: Conduct conference at [project site] <insert location>.
SECTION 074213.23 METAL COMPOSITE MATERIAL WALL PANELS PART 1 GENERAL 1.1 SUMMARY A. Exterior cladding consisting of formed metal composite material (MCM) sheet, secondary supports and anchors to structure,
More informationPROJECT IN SERIES 1300 NARROW SIGHT LINE AAMA/WDMA/CSA 101/I.S.2/A Structural Performance:
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT IN SERIES 1300 NARROW SIGHT
More informationSECTION EXTERIOR GRILLS AND SCREENS
SECTION 10 82 13 PART 1 GENERAL PART 1 1 SUMMARY A. Section Includes: 1. Exterior perforated aluminum screen wall system with Ombrae TM Optical Tile imaging technology. 2. Accessories including attachments,
More informationSECTION TERRA COTTA CLAY TILE RAINSCREEN SYSTEM
SECTION 07400 TERRA COTTA CLAY TILE RAINSCREEN SYSTEM PART 1 GENERAL 1.01 WORK INCLUDED A. The terra cotta clay tile elements and aluminum support system shall be manufactured by NBK Keramik GmbH as represented
More informationSERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651
SERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows
More informationK. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.
DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:
More informationHORIZONTAL SLIDER SERIES 700. Main Frame Depth: 2 3/4 Glazing Thickness (Maximum): 5/8 Thermal Break:
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 700 Main
More informationPROJECT OUT SERIES 6300 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT OUT SERIES 6300 AAMA/WDMA/CSA
More informationPROJECT OUT SERIES 6300 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT OUT SERIES 6300 AAMA/WDMA/CSA
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND CURTAINWALL
SECTION 084116 - ALUMINUM-FRAMED ENTRANCES AND CURTAINWALL PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Exterior and interior curtainwall framing. 2. Curtainwall framing for punched openings. 3.
More informationFL550 21/2 x5 GUIDE SPECIFICATION. Impact-Resistant Storefront
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 - GENERAL 1.1 SUMMARY. A. Section Includes:
SECTION 084113 - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Exterior storefront framing. 2. Storefront framing for ribbon walls. 3. Storefront framing
More informationCASEMENT PROJECT OUT SERIES 2400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 2 3/8
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 2400
More informationCASEMENT PROJECT OUT SERIES 6400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 6400
More informationSPECIFICATIONS FOR AluSystems Aluminum Composite Panels Series 20 Dry Joint 1.00 GENERAL 1.01 RANGE OF WORK Section includes: Laminated panels and attachment systems for use as exterior cladding. A. Provide
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 084113 - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Exterior and interior storefront framing. 2. Exterior and interior manual-swing entrance
More informationPRODUCT SPECIFICATION THE 9500 SERIES FAMILY - SERIES 9502 / 9503 THERMALLY BROKEN ALUMINUM OUTSWING BALCONY DOOR
PART 1 - GENERAL 08 13 16 ALUMINUM DOORS (Outswing Aluminum-Framed Glass Doors) A high-quality thermally broken aluminum balcony outswing door designed for residential high rise construction. 1.1 SUMMARY
More informationSECTION (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 41 13 (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Interior and Exterior Aluminum Storefront Framing, Doors, Door Frames, Lights, and
More informationA. Pre-Installation Conference: Conduct conference at [project site] <insert location>.
SECTION 074213.23 METAL COMPOSITE MATERIAL WALL PANELS PART 1 GENERAL 1.1 SUMMARY A. Exterior cladding consisting of formed metal composite material (MCM) sheet, secondary supports and anchors to structure,
More informationSECTION EXTERIOR SUN SHADES
SECTION 10 71 13 EXTERIOR SUN SHADES USE THIS SECTION WHEN SPECIFYING C.R. LAURENCE 7700 SERIES ALUMINUM SUN SHADE SYSTEMS. THE CRL 7700 SERIES SUN SHADE SYSTEM IS A FIXED BAR GRILLE STYLE WITH A TAPERED
More informationDesign and Construction Standards SECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 GENERAL 1.1 RELATED DOCUMENTS: A. Documents affecting work of this section include but are not necessarily limited to, General Conditions, special provisions and sections
More informationArchitectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION
Architectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION Section 08520 Aluminum Windows PART 1: WORK INCLUDED A. The conditions of the contract and applicable sections of Division
More informationPRODUCT SPECIFICATION SERIES 9000 WINDOW WALL THERMALLY BROKEN ALUMINUM CASEMENT / AWNING / FIXED WINDOW
08 46 3 GLAZED ALUMINUM WINDOW WALL PART - GENERAL A high-quality thermally broken 4 ½ aluminum window wall designed for residential high rise construction.. SUMMARY A. Section Includes: Glazed Aluminum
More informationLOG COLLEGE MIDDLE SCHOOL
PART 1-GENERAL 1.1 SUMMARY A. This section includes the following: 1. Curb-mounted plastic glazed skylights. B. Refer to roofing system sections for roofing accessories to be built into the roofing system
More informationWindow Installation Instructions Hung Window Systems with Receptor Pan
STANDARD PROCEDURE No. I-110 Window Installation Instructions Hung Window Systems with Receptor Pan Examined, Accepted and Approved By: D Ray VanNess Title: President SUBJECT: Window Installation Instructions
More informationFL550T 21/2 x5. GUIDE SPECIFICATION Series FL550T Thermal (21/2 x 5 ) Impact-Resistant Storefront. Thermal Impact-Resistant Storefront
Series FL550T Thermal (21/2 x 5 ) Impact-Resistant Storefront Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410
More informationWindow Installation Instructions Fixed Systems with Subframes
STANDARD PROCEDURE No. I-103 Window Installation Instructions Fixed Systems with Subframes Examined, Accepted and Approved By: D Ray VanNess Title: President SUBJECT: Window Installation Instructions Page
More informationT700 SERIES(AW50)-Impact (Formerly 8050 series) SINGLE HUNG 3 1/4 FRAME DEPTH (SIDE LOAD)
T700 SERIES(AW50)-Impact (Formerly 8050 series) SINGLE HUNG 3 1/4 FRAME DEPTH (SIDE LOAD) FEATURES 1.) Available Configurations -Single hung -Oriel style (optional) 2.) Main frame / Sash -Drop-in glazing
More informationSECTION PREHUNG WOOD DOORS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 08 14 00 PREHUNG WOOD DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2014-2016 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. French Doors.
More informationTMW 450 TECHNICAL MANUAL
ARCHITECTURAL METALS, INC. TMW 450 TMW 450 TECHNICAL MANUAL TMW 450 ARCHITECTURAL METALS, INC. BLANK PAGE FEATURES ARCHITECTURAL METALS, INC. TMW 450 FEATURES TMW 450 is 6 3/4" deep with a 2" wide sightline
More informationSECTION GLAZED ALUMINUM CURTAIN WALLS PART 1 GENERAL 1.01 RELATED DOCUMENTS
SECTION 08 4413 - PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationHeavy Commercial / Architectural Projected Windows Series L900T AW150
Heavy Commercial / Architectural Projected Windows Series L900T AW150 Section 08520...Aluminum Windows PART 1: WORK INCLUDED GUIDE SPECIFICATION A. The conditions of the contract and applicable sections
More informationSECTION ALL ULTREX DOUBLE HUNG WINDOW
SECTION 08 54 13 ALL ULTREX DOUBLE HUNG WINDOW PART 1 GENERAL 1.1 SECTION INCLUDES A. All Ultrex double hung window complete with hardware, glazing, weather strip, insect screen and half screen, grillesbetween-the
More informationFIBREGLASS CURTAIN WALL & ASSEMBLIES Issued for Bid Page 1 of 10 Section
Issued for Bid Page 1 of 10 Section 08 44 12.13 Part 1 General 1.1 SUMMARY.1 Section Includes: 1.2 REFERENCE.1 This Section specifies stick built curtain wall frames consisting of fibreglassreinforced
More informationA. Omega-Lite aluminum-faced composite panels, air and vapor barrier, attachments and sealants.
Section 07 42 13 Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES A. Omega-Lite aluminum-faced composite panels, air and vapor barrier, attachments and sealants. 1.2 RELATED SECTIONS A. Section 06112 - Framing
More informationDETENTION / SECURITY WINDOWS SECTION 08660
SWI Steel Window Specifications DETENTION / SECURITY WINDOWS SECTION 08660 Steel Window Institute, Inc. 1300 Sumner Ave. Cleveland, OH 44115-2851 Phone: 216-241-7333 Fax: 216-241-0105 E-Mail: swi@steelwindows.com
More informationWESTECK WINDOWS and DOORS
WESTECK WINDOWS and DOORS SECTION 08565 WOOD WINDOWS CASEMENT AWNING FIXED GENERAL Supply Wood windows as per approved Shop Drawings. PART 1 1.1 SECTION INCLUDES A. Casement Window Units. B. Awning Window
More informationGuide Specification for Pre-Engineered Skylight System. A. Engineering, design and drafting of the entire skylight system.
Guide Specification for Pre-Engineered Skylight System SECTION 08630 - METAL FRAMED SKYLIGHTS PART 1 GENERAL 1.01 SECTION INCLUDES A. Engineering, design and drafting of the entire skylight system. B.
More informationSECTION ALUMINUM GLASS FLOOR SKYLIGHT SYSTEMS
PART 1: GENERAL 1.01 SUMMARY SECTION 04818 ALUMINUM GLASS FLOOR SKYLIGHT SYSTEMS A. Structural glass floor system, consisting of structural extruded aluminum System or Stainless Steel system and laminated
More informationGuideline Specifications
Page 1 of 7 PART 1 Guideline Specifications Exterior Aluminum/Composite Wall Panels GENERAL ARROWHEAD 508 SYSTEM Pressure Equalized Rainscreen SECTION 07410 1.01 SUMMARY A. Work of this section included
More informationA M E R I C A N A R C H I T E C T U R A L M A N U F A C T U R E R S A S S O C I A T I O N
A M E R I C A N A R C H I T E C T U R A L AAMA 2410-13 Standard Practice for Installation of Windows with an Exterior Flush Fin Over an Existing Window Frame M A N U F A C T U R E R S A S S O C I A T I
More information4600 Series Specifications (Section 08520)
4600 Series Specifications (Section 08520) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for this project as
More informationSECTION COPPER WALL PANELS. ***This section has been updated to IBC. Verify for specific project conditions.***
***This section has been updated to IBC. Verify for specific project conditions.*** PART 1 GENERAL 1.1 SUMMARY ***Edit to project requirements*** A. Section Includes: 1. Clear copper and preweathered copper
More informationSECTION NEW WOOD WINDOWS. 1. Section Wood Window Restoration. 2. Section Painting.
SECTION 08610 NEW WOOD WINDOWS PART 1 - GENERAL 1.1 SUMMARY A. Provide new wood double hung, casement and awning windows and frames, complete, as shown and specified. 1. The new windows and frames shall
More informationTMS 114 XT TECHNICAL MANUAL
TECHNICAL MANUAL BLANK PAGE FEATURES FEATURES is center set flush glazed systems that are 4 1/2" deep with a 2" wide sightline Glaze from the outside or inside Screw spline or shear block fabrication Glazing
More information6400 Series TRIPLE GLAZED THERMAL BREAK CHURCH WINDOWS America's finest custom windows MINIMUM 5 8" AIR SPACE 3 1 2" SCALE = FULL SIZE
Since 906 Series The Series is a heavy triple glazed church window incorporated into a " thermally broken frame. The thermal break is achieved with the use of Thermal Strip technology. Two different aluminum
More informationSECTION METAL FRAMED SKYLIGHTS
SECTION 08630 - METAL FRAMED SKYLIGHTS PART 1: GENERAL 1.01 SUMMARY A. Section includes: Design, structural engineering, manufacture, fabrication, finishing of metal-framed skylights: 1. Glass and glazing
More information.2 Section Waste Management and Disposal.
Issued 2005/06/01 Section 08800 Glazing Page 1 of 6 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01330 Submittal Procedures.2 Section 01355 Waste Management and Disposal..3 Section 01450 Quality Control.4
More informationHORIZONTAL SLIDER SERIES 900 ANSI/AAMA/NWWDA 101/I.S Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.66. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 900 ANSI/AAMA/NWWDA
More informationHORIZONTAL SLIDER SERIES 910 ANSI/AAMA/NWWDA 101/I.S Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.66. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 910 ANSI/AAMA/NWWDA
More information