SIROPLAST-K. Pipe system for civil engineering subsoil drainage inspection chambers and subsoil drainage pipes to DIN

Transcription

1 HEGLER II/1 Pipe system for civil engineering subsoil drainage inspection chambers and subsoil drainage pipes to DIN : Pipe system consisting of inspection chambers and subsoil drainage pipes. Twin wall pipes with a smooth bore and structured-wall external profile to DIN R2 SD. Locally slotted pipe: DN 100 to DN 200 Totally slotted pipe: DN 100 to DN 400 Multi-purpose pipe: DN 200 to DN 400 Corrugated and Twin Wall Pipes of Plastics

2 : The Twin Wall Pipe System subsoil drainage pipe made from PE-HD, robust, strong and particularly resistant to corrosion in twin wall design, with smooth inner and profiled outer wall, flexible along its longitudinal axis circular shape, particularly good hydraulic properties special HEGLER slotting technique: a great number of short, clean-edged slots fully complying with the requirements of road and tunnel construction (suitable for traffic loads, SLW 60) the robust subsoil drainage pipe of PE-HD pipes are made from PE-HD. PE-HD being rupture-proof and impact-resistant down to -40 C and remaining inherently stable up to 100 C, the pipes can be installed at extreme temperatures and withstand even the roughest handling on site. Polyethylene has special surface properties. Due to this, the flow coefficient is low and deposits cannot settle easily. This is why has high flow rates, is easy to clean and abrasion-resistant. Polyethylene has a high resistance to chemical and biochemical influences. This makes the pipe resistant to any aggressive substances to be found in the ground. Special pipe geometry drainage pipes are socalled twin wall pipes with a corrugated outside and a smooth inner surface. Especially when partially filled, the smooth, circular inner pipe offers better hydraulic properties than pipes with boxtype bottom. Longitudinal cross-section of profile with adjoining coupler wall While twin wall pipes in general, and those of PE-HD in particular are very flexible, they never get out of shape. Settling of soil as it often occurs does not harm the pipes. The marking at the pipe crown guarantees proper positioning of the slotted part. Light weight, strong, flexible pipes are twin wall pipes according to DIN They fully meet the requirements of the new standard DIN (piping systems for civil engineering subsoil drainage). They are classified in pipe class R2 and category SD. They are extremely strong in spite of their light weight. Nevertheless, pipes are relatively flexible along their longitudinal axis and are able to follow soil movements thanks to their structured wall. As to mechanical strength, the pipe has been designed to withstand the loads occurring in public road con- struction (e. g. bridge class 60/30 according to DIN 1072). In landfill drainage, can be laid in the upper layers and as lateral drains. Unique slotting technique The water inlets are a characteristic feature of all types of HEGLER drainage pipes. Compared with other pipes, HEGLER drainage pipes stand out for the great number of short, clean-edged water inlets. They are located in the corrugation valleys to keep the resistance to water inflow as low as possible. This makes the water absorption capacity high and maintains the stability of the pipe. No widening of slots will occur, even under varying loads. 2

3 with Unique Features SIRBAU-spezial subsoil drainage pipe high ring stiffness of S 8.0 kn/m2 to DIN EN IS 9969 wide slots to ensure reliable and long-term water inflow ( 3.0 mm) made from PE-HD, robust, strong and particularly resistant to corrosion circular shape, good hydraulic properties, smooth inner and profiled outer wall fully complying with the requirements of road, tunnel and civil engineering construction (suitable for traffic loads, SLW 60) SIRBAU-spezial the special subsoil drainage pipe of SN 8 The discharge and water inlet capacity of conventional drainage pipes to DIN may be insufficient in case of large water volumes or when pipes are to be laid in great depths. SIRBAU-spezial, the special subsoil drainage pipe from HEGLER, meets the requirements of exactly these applications: It is of a higher ring stiffness, namely S 8.0 kn/m2 to DIN EN IS 9969 or S R kn/m 2 to DIN For nominal sizes DN 300, 400, 500 and 600, the required cross-sectional areas of discharge as specified in DIN are met. Depending on the slotting pattern (TP or MP), the water inlet area equals or exceeds 180 cm 2 /m or 50 cm 2 /m. For applications where special requirements for the protection of structures have to be met, the SIRBAU-spezial subsoil drainage pipe is available in slot widths of 3.0 mm and wider as of nominal size DN 300, thus exceeding the requirements of DIN (DN 200 and DN 250: 2.0 mm). AQUATUB-Rw the storm sewer pipe for public road construction of SN 8 In Germany, sewer pipes of nominal size DN 300 or larger are normally used for the discharge of water collected from road construction. HEGLER recommends its AQUATUB-Rw storm sewer pipe in twin wall design for this purpose (nominal sizes 150 to 600 mm). Although lighter in weight than conventional pipes, AQUATUB-Rw is designed to meet the load requirements: S 8.0 kn/m2 to DIN EN IS 9969 or S R kn/m 2 to DIN It is very robust like all PE pipes, which offers essential advantages in laying. If laid in depths between 0.80 m and 5.00 m and in accordance with DIN EN 1610, the pipe is allowed to be installed without a structural analysis. therwise, proof has to be furnished. Quality control The constant quality of HEGLER drainage pipes and HEGLER storm sewer pipes is guaranteed by a supervision contract with the official testing laboratory, Süddeutsches Kunststoffzentrum (SKZ) at Würzburg. Test and certification marks: A 102 SIRBAU-spezial A 353 AQUATUB-Rw A 352 pipes are marked as follows, for example: HEGLER SIRPLAST 200 PE R2 SD 04 1 DIN NF P SKZ A 102 subsoil drainage pipes are in compliance with DIN R2 SD and thus come up to the requirements of the public hand. 3

4 SIRBAU S 300/S 400: The Innovative Cha SIRBAU inspection chambers made from PE-HD, robust, strong and particularly resistant to corrosion in twin wall design, with smooth inner and profiled outer wall, low weight high ring stiffness of S 8.0 kn/m2 to DIN EN IS 9969, easy to handle on site suitable for TV inspection and flushing pipes and chambers are a system: reliability as to design and installation Pipe system Standardized pipes and prefabricated inspection and flushing chambers adapted to the pipes can contribute to rationalization in use. This is what has been taken into account with the drainage system: Apart from the complete size range to DIN , there are two chamber models adapted to these sizes. The specifications in the STLK code for road and bridge construction (section 110 drainage of roads) being no longer in compliance with the standards, we recommend to download the form for inviting tenders from our website: SIRBAU inspection and flushing chambers The SIRBAU chambers are fabricated from twin wall pipe with flat plateaus to form the connection areas. These plateaus are cut out of the body and take up the respective outlets/adaptors. There are two models with different inner diameters (SIRBAU S 300: d i = 300 mm and SIRBAU S 400: d i = 400 mm) to cover the complete size ranges of and SIRBAU-spezial pipes. According to their intended use, the standard chambers have two outlets for straight passage. Due to the fact that the pipes can be squared off by approx. 7, installation in a polygonal course is possible. Which chamber model is to be chosen for the individual pipe diameters can be taken from the opposite table. For adapting the chamber depth to the gradients, chamber raising pieces are available that can be cut to height on the construction site. Chamber covers made of cast iron are offered in classes A, B and D. For connection to concrete manholes, we can supply the appropriate liners. Quality control SIRBAU S 300 and S 400 chambers are subject to quality control to works standards and supervision and further testing by the official testing laboratory Süddeutsches Kunststoffzentrum (SKZ) at Würzburg. Special attention is being paid to the stiffness of the chamber body which is tested to DIN EN IS 9969 (S 8.0 kn/m2 ). This guarantees that the chambers will withstand the loads from soil pressure and traffic. 4

5 ø mber Systems for Road Drainage ø 464 cast iron (A 15/ B 125/ D 400) /3 outlets ø 400 ø Inspection and flushing chamber SIRBAU S 400 Chamber raising piece Chamber covers SIRBAU Chamber Systems and Accessories Product SIRBAU S 300 SIRBAU S 400 (MULTI-inspect S 400) SIRBAU chamber without sand trap effective length: 82 cm effective length: 123 cm pipes that can be connected DN DN SIRBAU-spezial DN AQUATUB-Rw DN SIRBAU raising piece effective length: 63 cm effective length: 123 cm effective length: 109 cm Chamber covers class A 15 class B 125 (without vent openings) class B 125 (with vent openings) class B 125 (grid) class D 400 (without vent openings) class D 400 (with vent openings) class D 400 (grid) Profiled seal Coupling Dirt bucket Filter bag 5

6 : The Twin Wall Pipe System accessories and fittings versatile and manifold robust and strong compatible with other HEGLER pipe products Accessories pipes are connected by means of slip couplings. For multipurpose lines, profiled sealing rings are available. Thanks to the extensive range of accessories, pipes are most versatile in use. They are just as well suited for systems consisting of laterals and mains as usual in sports field drainage as they are for subsoil drains and drainage systems for the protection of structures in contact with the soil. The accessory being interchangeable with that for the storm sewer pipe AQUATUB-Rw, there is an extensive range of fittings for all nominal sizes and applications. In case that special-purpose fittings not covered by our standard fitting range are required with the pipe as is often the case in civil engineering construction fittings can be tailored to the customer's request. The nominal ring stiffness of fittings comes up to that of the connected pipe system. With suitable branches/adaptors and either a 150 mm flexible connecting pipe AQUATUB-RwR or a 150 mm solid-wall sewer pipe to DIN multi-purpose drains of diameters between 250 mm and 400 mm can be connected to road gullies. 6

7 with Unique Features Coupling Adaptor to sewer pipe spigot end (SE) Adaptor to sewer pipe socket end (ME) Branch 45 Bend 45 Adaptor and flexible gully connecting pipe Accessories and Fittings Nominal size DN Coupling Reducer Adaptor to sewer pipe spigot end socket end utlet Manhole (concrete) connection Plug Profiled seal Branch 45 Reducing branch 45 Branch 90 Reducing branch 90 Bend 45 Bend 90 Special fittings on request 7

8 Important: If possible, pipes should be transported and stored on site in the original stillages. They should always be stored on an even and smooth surface. The pipe material is protected against damages by UV radiation. Nevertheless, the pipes should not be stored in the open air for more than 2 years. Continuous support at the given gradient should be provided in the pipe trench. The supporting layer of at least 10 cm in thickness must consist of sand. Local depressions should be provided at joints so that the couplings do not initially rest on the support. Joints should be made using the recommended lubricant. In order to ensure long-term operation of the drainage system, pipes should be embedded in filter material composed in accordance with the Terzaghi filter regulations. For embedding, DIN EN 1610 should be observed. It is recommended to use sand/gravel 0/8. Chambers should be embedded in a sand/gravel layer (d 20 cm). The bedding material should be compacted layer by layer. Compacting equipment should not be applied directly on top of the pipes. In the vicinity of pipes, light compacting equipment should be used. Pipes may be cleaned by highpressure flushing devices at a maximum flushing pressure of 120 bar. The information given in this brochure is the most up-to-date available and is intended to provide information on our products and their possible applications. It is not a guarantee of certain features or of their suitability for certain specific applications. ur guarantee applies to compliance with our specifications, within the scope of our General Terms and Conditions. The schematic drawings (pipe/accessories) are indicative only. They are not binding as to product geometry. Subject to change. Technical details Nominal size DN utside diameter mm Inside diameter mm Discharge area cm Water inlet area cm 2 /m > 50 Width of slots to DIN Standard length (20 C) m 6.00 Bending radius m > 5 > 6 Standard design locally slotted (LP) multi-purpose (MP) Special design Packing details SIRBAU-spezial (SN 8) Technical details Packing details totally slotted (TP) Nominal size DN Stillage contents lengths m Stillage length m dimensions width m height m Nominal size DN utside diameter mm Inside diameter mm Discharge area cm Water inlet area cm 2 /m > 180 Width of slots* about 2 mm to DIN or 3 mm resp. Standard length (20 C) m 6.00 Standard design * special width exceeding DIN project-specific production Nominal size DN Stillage contents lengths m Stillage length m dimensions width m height m Corrugated and Twin Wall Pipes of Plastics HEGLER PLASTIK GMBH. D erlenbach/germany. Phone Fax