SECTION PAINT. A. Section Cast-In-Place Concrete: Preparation of concrete wall assemblies to receive finishes.

Transcription

1 SECTION PAINT PART 1 GENERAL 1.1 SECTION INCLUDES A. Interior Primer. B. Interior Paint. C. Exterior Primer. D. Exterior Paint. E. Wall Preparation. 1.2 RELATED SECTIONS A. Section Cast-In-Place Concrete: Preparation of concrete wall assemblies to receive finishes. B. Section Precast Concrete: Preparation of precast wall assemblies to receive finishes. C. Section Masonry Assemblies: Preparation of masonry wall assemblies to receive finishes. D. Section Metal Fabrications: Preparation of prefabricated metal to receive finishes. E. Section Ornamental Metal: Preparation of ornamental metal components to receive finishes. F. Section Finish Carpentry: Preparation of wood surfaces to receive finishes. G. Section Wood Siding: Preparation of wood siding prepared to receive finishes. H. Section Plaster and Gypsum Board: Preparation of interior wall sheathing to receive finishes. 1.3 REFERENCES A. Green Promise 2010 B. Green Seal Standard GS-11; May 20, C. MPI (APL) - Master Painters Institute. D. SCAQMD South Coast Air Quality Management District Rule #1168; October 3, E. SSPC (PM1) - Steel Structures Painting Manual, Vol. 1, Good Painting Practice;

2 Society for Protective Coatings; 1993, Third Edition. F. SSPC (PM2) - Steel Structures Painting Manual, Vol. 2, Systems and Specifications; Society for Protective Coatings; 1995, Seventh Edition. G. 40 CFR 59, Subpart D - National Volatile Organic Compound Emission Standards for Architectural Coatings; U.S. Environmental Protection Agency; current edition. 1.4 DEFINITIONS A. Paints are available in a wide range of sheens or glosses, as measured by a gloss meter from a 60 degree angle from vertical, as a percentage of the amount of light that is reflected. The following terms are used to describe the gloss of our products. 1. Flat - Less than 5 units. 2. Matte units. 3. Eggshell units. 4. Satin units. 5. Semi-Gloss units. 6. Gloss units. 1.5 SUBMITTALS A. Submit under provisions of Section B. Coordinate with Section Submittals, for submittal procedures and LEED Submittal Forms MRc3, MRc4, MRc5. C. LEED Certification Product Data: 1. See Section Green Building Requirements, for LEED certification submittal forms and certification templates. 2. Submittals Required: a. MRc3 Resource Reuse (LEED Form). b. MRc4 Recycled Content (LEED Form). c. MRc5 Local and Regional Materials (LEED Form). d. EQc4.1 Low Emitting Materials - Adhesives and Solvents (VOC Certification Letter). e. EQc4.2 Low Emitting Materials - Paint (VOC Certification Letter). f. Green Seal Standard GS-11 Certified Product certificates. D. Product Data: Provide a complete list of all products to be used, with the following information for each: 1. Manufacturer's name, product name and/or catalog number, and general product category. 2. Cross-reference to specified paint system(s) that the product is to be used in; include description of each system. E. Samples: Submit three paper samples, 5 inches by 7 inches (127mm x 178mm) in size, illustrating selected colors for each color and system selected with specified coats cascaded. F. Manufacturer's Instructions: Indicate special surface preparation procedures. G. Maintenance Data: Submit data on cleaning, touch-up, and repair of painted and coated surfaces. 1.6 QUALITY ASSURANCE A. Manufacturer Qualifications: a single manufacturer with a minimum of ten (10) years

3 experience will supply all primary products specified in this section. B. Installer Qualifications: All products listed in this section are to be installed by a single installer with a minimum of five (5) years demonstrated experience in installing products of the same type and scope as specified. C. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship. 1. Finish areas designated by Architect. 2. Do not proceed with remaining work until Architect approves workmanship, color, and sheen. 3. Refinish mock-up area as required to produce acceptable work. 1.7 DELIVERY, STORAGE, AND HANDLING A. Store products in manufacturer's unopened packaging until ready for installation. B. Store and dispose of solvent-based materials, and materials used with solventbased materials, in accordance with requirements of local authorities having jurisdiction. C. Disposal: 1. Never pour leftover coating down any sink or drain. Use up material on the job or seal can and store safely for future use. 2. Do not incinerate closed containers. 3. For specific disposal or recycle guidelines, contact the local waste management agency or district. Recycle whenever possible. 1.8 PROJECT CONDITIONS A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits. 1.9 WARRANTY A. At project closeout, provide to the Owner or owner's representative an executed copy of the Manufacturer's standard form outlining the terms and conditions of and any exclusions to their Limited Warranty against Manufacturing Defect EXTRA MATERIALS A. At project closeout, supply the Owner or owner's representative one gallon of each product for touch-up purposes. B. At project closeout, provide the color mixture name and code to the Owner or owner's representative for accurate future color matching. PART 2 PRODUCTS 2.1 MANUFACTURERS A. Acceptable Manufacturer: Benjamin Moore & Co., which is located at: 101 Paragon Drive, Montvale, NJ 07645; Toll Free Tel: ; Tel: ; info@benjaminmoore.com; Web: B. Approved Manufacturers

4 1.Coronado Paints C. Substitutions: Not permitted. D. Requests for substitutions will be considered in accordance with provisions of Section LEED CRITERIA A. All paints and coatings used must meet the VOC limits of Green Seal Standard GS- 11: 1. Interior: 50 g/l VOC or less for Flats and 150 g/l VOC for Non Flats. 2. Exterior: 100 g/l VOC for Flats and 200 g/l VOC or Less for Non Flats. B. EQ CR4.2 Low Emitting Materials: 1 Credit - Paint 2.3 MATERIALS - GENERAL A. Volatile Organic Compound (VOC) Content: 1. Provide coatings that comply with the most stringent requirements specified in the following: a. 40 CFR 59, Subpart D--National Volatile Organic Compound Emission Standards for Architectural Coatings. b. Determination of VOC Content: Testing and calculation in accordance with 40 CFR 59, Subpart D (EPA Method 24), exclusive of colorants added to a tint base and water added at project site; or other method acceptable to authorities having jurisdiction. B. Compatibility: Provide materials that are compatible with one another and the substrates indicated under conditions of service and application, as demonstrated by manufacturer based on testing and field experience. 2.4 MIXING AND TINTING A. Except where specifically noted in this section, all paint shall be ready-mixed and pre-tinted. Agitate all paint prior to and during application to ensure uniform color, gloss, and consistency. B. Thinner addition shall not exceed manufacturer's printed recommendations. Do not use kerosene or other organic solvents to thin water-based paints. C. Where paint is to be sprayed, thin according to manufacturer's current guidelines. 2.5 EXTERIOR PRIMERS - NEW CONSTRUCTION A. Concrete or Stucco: a. One (1) Coat - Fresh Start All Purpose Alkyd Primer #024 (MPI Listed Product, Category 45). b. One (1) Coat - Super Spec Exterior Alkyd Primer #176 c. One (1) Coat - Moore's Alkyd Masonry Sealer #C077. a. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer #023 (MPI b. One (1) Coat - Fresh Start 100% Acrylic Superior Primer #046 (MPI Listed Product Categories 6, 17, 39, 50, 137) c. One (1) Coat - Aura Interior Exterior Color Foundation #521. d. One (1) Coat - Super Spec Latex Exterior Primer #169 (MPI Listed

5 Product, Category 6). e. One (1) Coat - Moore's Acrylic Masonry Sealer #066. f. One (1) Coat - Moore's High Build Acrylic Masonry Primer #068. g. One (1) Coat - Super Spec HP Clear Acrylic Sealer P27. h. One (1) Coat - Exterior Acrylic latex primer #102 (Canada i. One (1) Coat - MooreStyle Exterior Acrylic latex primer #582 (Canada B. Concrete Masonry Units: 1. Latex: a. One (1) Coat - Super Craft Latex Block Filler #285 (MPI Listed Product, Category 4). b. One (1) Coat - Moore's High Build Acrylic Masonry Primer #068. c. One (1) Coat - Super Spec Satin-Fil #172. d. One (1) Coat - Super Spec Latex Block Filler 160. e. One (1) Coat - Super Spec HP Clear Acrylic Sealer P27 f. One (1) Coat - Exterior Acrylic latex primer #102 (Canada g. One (1) Coat - MooreStyle Exterior Acrylic latex primer #582 (Canada h. One (1) Coat - Aura Interior Exterior Color Foundation #521. C. Ferrous Metals: a. One (1) Coat - Super Spec HP Alkyd Metal Primer #P06. b. One (1) Coat - Super Spec HP Universal Alkyd Metal Primer #P07. c. One (1) Coat - Super Spec HP Shop-Cote Alkyd Metal Primer #P14. d. One (1) Coat - IronClad Alkyd Low Lustre Metal & Wood Enamel #C163 (MPI Listed Product, Category 79). e. One (1) Coat - Super Spec HP D.T.M. Alkyd Semi-Gloss #P24 (MPI Listed Product, Category 81). f. One (1) Coat - Super Spec HP D.T.M. Alkyd Gloss Enamel #P26. g. One (1) Coat - Fresh Start Rust Inhibitive Primer # 163 (Canada a. One (1) Coat - IronClad Latex Low Lustre Metal & Wood Enamel #363. b. One (1) Coat - Super Spec HP Acrylic Metal Primer # P04 (MPI Listed Product, Category 107 and Category 134). c. One (1) Coat - Super Spec HP D.T.M. Acrylic Gloss Enamel #P28 (MPI Listed Product, Category 114). d. One (1) Coat - Super Spec HPD.T.M. Acrylic Semi-Gloss #P29 (MPI Listed Product, Category 141). 3. Epoxy: a. One (1) Coat - Super Spec HP Waterborne Polyamide Epoxy Primer #P42-70/P42-84 b. One (1) Coat - Super Spec HP Epoxy Mastic Coating #P45/P45-84 (MPI Listed c. One (1) Coat - Super Spec HP Polyamide Epoxy Primer #P31-70/P D. Galvanized Metals: 1. Latex: a. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer #023 (MPI b. One (1) Coat - IronClad Latex Low Lustre Metal & Wood Enamel #363. c. One (1) Coat - Super Spec HP Acrylic Metal Primer #P04 (MPI Listed Product, Category 107 and Category 134). d. One (1) Coat - Super Spec HP D.T.M. Acrylic Gloss Enamel #P

6 (MPI Listed Product, Category 114). e. One (1) Coat - Super Spec HPD.T.M. Acrylic Semi-Gloss #P29 (MPI Listed Product, Category 141). f. One (1) Coat - Super Spec Exterior Acrylic Primer #169 g. One (1) Coat - Aura Interior Exterior Color Foundation #521. E. Aluminum: 1. Latex: a. One (1) Coat - Super Spec HP Acrylic Metal Primer #P04 (MPI Listed Product, Category 107 and Category 134). b. One (1) Coat - IronClad Latex Low Lustre Metal & Wood Enamel #363. c. One (1) Coat - Super Spec HP D.T.M. Acrylic Gloss Enamel #P28 (MPI Listed Product, Category 114). d. One (1) Coat - Super Spec HP D.TM. Acrylic Semi-Gloss #P29 (MPI Listed Product, Category 141). e. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer #023 (MPI F. Wood Surfaces: a. One (1) Coat - Fresh Start All Purpose Alkyd Primer #024 (MPI Listed Product, Category 45). b. One (1) Coat - Benjamin Moore Fresh Start Fast-Dry Alkyd Primer #094. c. One (1) Coat - Benjamin Moore Fresh Start MoorWhite Penetrating Alkyd Primer #100. d. One (1) Coat - Super Spec Alkyd Exterior Primer #176 (MPI Listed Product, Category 7). e. One (1) Coat - Exterior Alkyd Primer # 583 (Canada a. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer #023 (MPI b. One (1) Coat - Super Spec Latex Exterior Primer #169 (MPI Listed Product, Category 6). c. One (1) Coat - Aura Interior Exterior Color Foundation #521. d. One (1) Coat - Exterior Acrylic latex primer #102 (Canada e. One (1) Coat - MooreStyle Exterior Acrylic latex primer #582 (Canada G. Water Resistant Soffit Board and Ceiling Board: a. One (1) Coat - Fresh Start All Purpose Alkyd Primer #024 (MPI Listed Product, Category 45). b. One (1) Coat - Benjamin Moore Fresh Start Fast-Dry Alkyd Primer #094. c. One (1) Coat - Super Spec Alkyd Exterior Primer #176 (MPI Listed Product, Category 7). d. One (1) Coat - Benjamin Moore Fresh Start MoorWhite Penetrating Alkyd Primer # INTERIOR PRIMERS - NEW CONSTRUCTION A. Concrete, Stucco: a. One (1) Coat - Fresh Start All Purpose Alkyd Primer #024 (MPI Listed Product, Category 45). b. One (1) Coat - Super Spec Alkyd Enamel Undercoater & Primer

7 Sealer C245 (MPI Listed Product, Category 45 and Category 46). c. One (1) Coat - Alkyd Primer Sealer #200 (Canada d. One (1) Coat - Alkyd Enamel Underbody #217 (Canada a. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer #023 (MPI b. One (1) Coat - Aura Interior Exterior Color Foundation #521. c. One (1) Coat - Natura 0 VOC Acrylic Latex Primer #511. d. One (1) Coat - Eco Spec WB Interior Latex Primer #372. e. One (1) Coat - Ben Interior Latex Primer #624. f. One (1) Coat - Moorcraft Super Spec Latex Enamel Undercoater & Primer Sealer #253 (MPI Listed Product, Category 17 and Category 50). g. One (1) Coat - Super Spec Prep Coat High Build Latex Primer #270 h. One (1) Coat - Regal First Coat Interior Latex Primer & Underbody #216 (MPI Listed Product, Category 50). i. One (1) Coat - Super Spec Satin - fil #172. j. One (1) Coat - Super Spec Acrylic Self - leveling Low Lustre # K249 (Canada Only) k. One (1) Coat - Super Hide Interior Latex Primer/Undercoater #284. l. One (1) Coat - Super Spec Latex Vapor Barrier Primer Sealer #260. m. One (1) Coat - Eco Spec Interior Latex Primer Sealer #231(MPI Listed Product, Category 149). n. One (1) Coat - MooreStyle Interior Latex Primer Sealer #562 (Canada o. One (1) Coat - Latex Quick Dry Primer Sealer #201 (Canada p. One (1) Coat - Latex Enamel Underbody #345 (Canada B. Concrete Masonry Units: 1. Latex: a. One (1) Coat - Super Craft latex Block Filler #285 (MPI Listed Product, Category 4). b. One (1) Coat - Super Spec Satin-fil #172. c. One (1) Coat - Super Spec Latex Block Filler #M160. d. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer #023 (MPI e. One (1) Coat - Super Spec Prep Coat High Build Latex Primer #270. f. One (1) Coat - Aura Interior Exterior Color Foundation #521. g. One (1) Coat - Natura 0 VOC Acrylic Latex Primer #511. h. One (1) Coat - Eco Spec WB Interior Latex Primer #372. i. One (1) Coat Ben Interior Latex Primer #624. j. One (1) Coat - Moorcraft Super Spec Latex Enamel Under coater & Primer Sealer #253 (MPI Listed Product, Category 17 and Category 50). k. One (1) Coat - Super Spec Acrylic Self - leveling Low Lustre # K249 (Canada Only). l. One (1) Coat - Regal First Coat Interior Latex Primer & Underbody #216 (MPI Listed Product, Category 50). m. One (1) Coat - MooreStyle Interior Latex Primer Sealer #562 (Canada n. One (1) Coat - Latex Quick Dry Primer Sealer #201 (Canada o. One (1) Coat - Latex Enamel Underbody #345 (Canada C. Wood: a. One (1) Coat - Fresh Start All Purpose Alkyd Primer #024 (MPI Listed

8 Product, Category 45). b. One (1) Coat - Super Spec Alkyd Enamel Undercoater & Primer Sealer #C245 (MPI Listed Product, Category 45 and Category 46). c. One (1) Coat - Benjamin Moore Fresh Start Alkyd Enamel Underbody #217 (MPI Listed Product, Category 46). d. One (1) Coat- Alkyd Primer Sealer #200 (Canada e. One (1) Coat- MooreStyle Alkyd Interior Undercoat #572 (Canada a. One (1) Coat - Ultra Spec 500 Interior Latex Primer #N534 (MPI listed Product, Categories 50, 50-X, 149, 149-X) b. One (1) Coat - Aura Interior Exterior Color Foundation #521. c. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer #023 (MPI d. One (1) Coat - Natura 0 VOC Acrylic Latex Primer #511. e. One (1) Coat - Eco Spec WB Interior Latex Primer #372. f. One (1) Coat Ben Interior Latex Primer #624. g. One (1) Coat - Moorecraft Super Spec Latex Enamel Under coater & Primer Sealer #253 (MPI Listed Product, Category 17 and Category 50). h. One (1) Coat - Super Spec Prep Coat High Build Latex Primer #270. i. One (1) Coat - Regal First Coat Interior Latex Primer & Underbody #216 (MPI Listed Product, Category 50). j. One (1) Coat - Eco Spec Interior Latex Primer Sealer #231 (MPI Listed Product, Category 149). k. One (1) Coat - Latex Enamel Underbody #345 (Canada D. Ferrous Metal: a. One (1) Coat - Super Spec HP Shop-Cote Metal Primer #P14. b. One (1) Coat - IronClad Low Lustre Metal & Wood Enamel #C163 (MPI Listed Product, Category 79). c. One (1) Coat - Super Spec HP Alkyd Metal Primer #P06 (MPI Listed Product, Category 79). d. One (1) Coat - Super Spec HP Universal metal Primer #P07 (MPI Listed Product, Category 135). e. One (1) Coat - Super Spec HP D.T.M. Alkyd Semi-Gloss #P24 (MPI Listed Product, Category 81). f. One (1) Coat - Super Spec HP D.T.M. Alkyd Gloss Enamel #P26. g. One (1) Coat- Fresh Start Rust Inhibitive Primer # 163 (Canada a. One (1) Coat - IronClad Latex Low Lustre Metal & Wood Enamel #363. b. One (1) Coat - Super Spec Acrylic Metal Primer #P04 (MPI Listed Product, Category 107 and Category 134). c. One (1) Coat - Super Spec HP D.T.M. Acrylic Gloss Enamel #P28 (MPI Listed Product, Category 114). d. One (1) Coat - Super Spec HP D.T.M. Acrylic Semi-Gloss #P29 (MPI Listed Product, Category 141). 3. Epoxy: a. One (1) Coat Super Spec HP Waterborne Polyamide Epoxy Primer #P42-70/P42-84 b. One (1) Coat - Super Spec HP Epoxy Mastic Coating #P45/P45-84 (MPI Listed c. One (1) Coat - Super Spec HP Polyamide Epoxy Primer #P31-70/P

9 E. Galvanized Metal: 1. Latex: a. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer #023 (MPI b. One (1) Coat - Super Spec HP Acrylic Metal Primer #P04 (MPI Listed Product, Category 107 and Category 134). c. One (1) Coat - Super Spec HP D.T.M. Acrylic Gloss Enamel #P28 (MPI Listed Product, Category 114). d. One (1) Coat - Super HP D.T.M. Acrylic Semi-Gloss #P29 (MPI Listed Product, Category 141). e. One (1) Coat - IronClad Latex Low Lustre Metal & Wood Enamel #363. f. One (1) Coat - Aura Interior Exterior Color Foundation #521. g. One (1) Coat - Natura 0 VOC Acrylic Latex Primer #511. h. One (1) Coat - Eco Spec WB Interior Latex Primer #372. i. One (1) Coat - Ben Interior Latex Primer #624. F. Gypsum Board, Plaster: a. One (1) Coat - Fresh Start All Purpose Alkyd Primer #024 (MPI Listed Product, Category 45). b. One (1) Coat - Benjamin Moore Fresh Start Alkyd Enamel Underbody #217 (MPI Listed Product, Category 46). c. One (1) Coat - Super Spec Alkyd Enamel Under coater & Primer Sealer #C245 (MPI Listed Product, Category 45 and Category 46). a. One (1) Coat - Ultra Spec 500 Interior Latex Primer #N534 (MPI listed Product, Categories 50, 50-X, 149, 149-X) b. One (1) Coat Aura Interior Exterior Color Foundation #521. c. One (1) Coat - Regal First Coat Interior Latex Primer & Underbody #216 (MPI Listed Product, Category 50). d. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer #023 (MPI e. One (1) Coat - Natura 0 VOC Acrylic Latex Primer #511 f. One (1) Coat - Eco Spec WB Interior Latex Primer #372 g. One (1) Coat Ben Interior Latex Primer #624. h. One (1) Coat - Eco Spec Interior Latex Primer Sealer #231 (MPI Listed Product, Category 149). i. One (1) Coat - Super Spec Prep Coat High Build Latex Primer #270 j. One (1) Coat - Super Spec Latex Enamel Under coater & Primer Sealer #253 (MPI Listed Product, Category 17 and Category 50). k. One (1) Coat - Super Spec Latex Vapor Barrier Primer Sealer #260. l. One (1) Coat - Latex Quick Dry Primer Sealer #201 (Canada m. One (1) Coat - Super Spec Acrylic Self - leveling Low Lustre # K249 (Canada Only). n. One (1) Coat - Latex Enamel Underbody #345 (Canada o. One (1) Coat - MooreStyle Interior 100% Acrylic Latex Super Adherent Primer #563 (Canada p. One (1) Coat - Fresh Start Acrylic Latex Primer Sealer #562 (Canada 2.7 EXTERIOR PRIMERS - PREVIOUSLY PAINTED SURFACES A. Concrete, Masonry, Stucco: a. One (1) Coat - Fresh Start All Purpose Alkyd Primer # 024 (MPI Listed

10 Product, Category 45). b. One (1) Coat - Benjamin Moore Fresh Start MoorWhite Penetrating Alkyd Primer #100. c. One (1) Coat - Benjamin Moore Fresh Start Fast-Dry Alkyd Primer # 094. d. One (1) Coat - Moore's Alkyd Masonry Sealer #C077. e. One (1) Coat - Super Spec Alkyd Exterior Primer #176 (MPI Listed Product, Category 7). f. One (1) Coat - Benjamin Moore Fresh Start MoorWhite Penetrating Alkyd Primer #100. g. One (1) Coat- MooreStyle Exterior Alkyd Primer #583 (Canada a. One (1) Coat - Fresh Start All Purpose 100 Percent Acrylic Primer # 023 (MPI b. One (1) Coat - Aura Interior Exterior Color Foundation #521. c. One (1) Coat - Moore's Acrylic Masonry Sealer #066. d. One (1) Coat - Moore's High Build Acrylic Masonry Primer #068. e. One (1) Coat - Latex Exterior Primer #169 (MPI Listed Product, Category 6). 2.8 INTERIOR PRIMERS - PREVIOUSLY PAINTED SURFACES A. Previously Painted: a. One (1) Coat Advance Waterborne Interior Alkyd Primer #790 (MPI Listed Product, Category 172). b. One (1) Coat - Fresh Start All Purpose Alkyd Primer # 024 (MPI Listed Product, Category 45). c. One (1) Coat - Benjamin Moore Fresh Start Alkyd Enamel Underbody #217 (MPI Listed Product, Category 46). d. One (1) Coat - Alkyd Enamel Underbody #C245 (MPI Listed Product, Category 45 and Category 46). e. One (1) Coat - Benjamin Moore Fresh Start QD-30 Stain Blocking Primer #202 (MPI Listed Product, Category 136). f. One (1) Coat- Alkyd Primer Sealer #200 (Canada g. One (1) Coat- MooreStyle Interior Alkyd Under coater #572 (Canada a. One (1) Coat - Ultra Spec 500 Interior Latex Primer #N534 (MPI listed Product, Categories 50, 50-X, 149, 149-X) b. One (1) Coat - Aura Interior Exterior Color Foundation #521. c. One (1) Coat - Regal First Coat Interior Latex Primer & Underbody #216 (MPI Listed Product, Category 50). d. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer #023 (MPI e. One (1) Coat - Eco Spec WB Interior Latex Primer #372 f. One (1) Coat Ben Interior Latex Primer #624. g. One (1) Coat - Super Spec Latex Enamel Under coater & Primer Sealer #253 (MPI Listed Product, Category 17 and Category 50). h. One (1) Coat - Super Spec Latex Vapor Barrier Primer Sealer #260. i. One (1) Coat - Fresh Start All Purpose 100% Acrylic Primer # 023 (MPI j. One (1) Coat - Latex Quick Dry Primer Sealer #201 (Canada k. One (1) Coat - Latex Enamel Underbody #345 (Canada l. One (1) Coat - MooreStyle Interior 100% Acrylic Latex Super Adherent Primer #563 (Canada

11 2.9 EXTERIOR FINISH COATS m. One (1) Coat - Fresh Start Acrylic Latex Primer Sealer #562 (Canada n. One (1) Coat - Ultra Spec 500 Interior Latex Primer #N534 (MPI listed Product, Categories 50, 50-X, 149, 149-X Green) o. Regal Select Primer & Underbody #546 (MPI Listed Product, Category 50, 50 X-Green) A. Flat Finish: 1. Latex: a. Two (2) Coats - Aura Waterborne Exterior Flat Finish #629. (MPI Listed Product, Category 10) b. One (1) or Two (2) Coats - Regal Select High Build Exterior Flat Finish #N400 c. Two (2) Coats MoorLife Acrylic Flat Latex House Paint #N105 (MPI Listed Product, Category 10). d. Two (2) Coats - Super Spec Flat Latex House Paint #171 (MPI Listed Product, Category 10). e. Two (2) Coats - Super Spec 100% Exterior 100% Acrylic Flat #183 (MPI Listed Product, Category 10). f. Two (2) Coats- MooreStyle Exterior Acrylic Latex Flat #584 (Canada g. Two (2) Coats Super Spec Masonry 100% Acrylic Elastomeric Coating Flat Finish #056 (MPI Listed Product, Category 113). B. Low Luster Finish: a. Two (2) Coats IronClad Alkyd Low Lustre Metal & Wood Enamel #C163 (MPI Listed Product, Category 79). a. Two (2) Coats - Aura Waterborne Exterior Low Lustre Finish #634 (MPI Listed Product, Category 15). b. One (1) or Two (2) Coats Regal Select High Build Exterior Low Lustre Finish #N401 c. Two (2) Coats - MooreGard Low Lustre Fortified Acrylic House Paint #N103. d. Two (2) Coats - Moorelastic Elastomeric Coating Low Lustre 055. e. Two (2) Coats - Ironclad Latex Low Lustre Metal & Wood Enamel #363. f. Two (2) Coats - Super Spec Low Lustre Latex House Paint #N185. g. Two (2) Coats- 100% Acrylic Solid Deck & Siding Finish #065 (Canada C. Satin Finish: a. Two (2) Coats- Deck Finishes Solid Colour #095 (Canada b. Two (2) Coats- Deck & Siding Finishes - Alkyd Translucent #099 (Canada a. Two (1) (2) Coats - Aura Exterior Satin #631. b. Two (2) Coats - Moorcraft Super Spec Satin Fil #172. c. Two (2) Coats- Porch and Floor Latex Satin Enamel #122 (Canada D. Soft/Medium Gloss Finish: 1. Latex: a. One (1) or Two (2) Coats - Regal Select Premium Exterior Soft Gloss

12 Finish #N402 (MPI Listed Product, Category 11). b. Two (2) Coats - MooreGlo Soft Gloss Fortified Acrylic House Paint #N096. c. Two (2) Coats - Super Spec Latex House & Trim Paint #170. d. Two (2) Coats - Super Spec 100% Acrylic House & Trim #183. E. Semi-Gloss Finish: a. Two (2) Coats - Super Spec HP D.T.M. Alkyd Semi-Gloss #P24 (MPI Listed Product, Category 81). a. Two (2) Coats - Aura Exterior Semi-Gloss #632. b. Two (2) Coats - Super Spec D.T.M. Acrylic Semi - Gloss #P29 (MPI Listed Product, Category 141). c. Two (2) Coats - MooreStyle Exterior Acrylic Latex Semi - Gloss #588 (Canada F. High Gloss Finish: a. One (1) or Two (2) Coats Advance Waterborne Interior/Exterior Alkyd High Gloss #N794 (MPI Listed Product, Categories 157, 157 X-Green). b. Two (2) Coats - Impervo Alkyd High Gloss Metal & Wood Enamel #C133 (MPI Listed Product, Category 9 and 48). c. Two (2) Coats - Moore's House Paint #110. d. Two (2) Coats - Super Spec HP D.T.M. Alkyd Gloss Enamel #P26. e. Two (2) Coats - Super Spec Urethane Alkyd Gloss Enamel #P22 (MPI Listed Product, Category 9 and Category 48). f. Two (2) Coats - Moorcraft Super Spec Gloss House Paint #175. g. Two (2) Coats - MooreStyle Exterior Alkyd Gloss #589 (Canada h. Two (2) Coats - Metal Finishes Alkyd Rust Paint #161 (Canada i. Two (2) Coats - Porch and Floor Enamel #112. j. Two (2) Coats - Benjamin Moore Collection High Gloss Enamel #133 (Canada k. Two (2) Coats - MooreStyle Interior/Exterior High Gloss Enamel #579 (Canada a. Two (2) Coats - Impervex Latex High Gloss Metal & Wood Enamel #309 (MPI Listed Product, Category 114). b. Two (2) Coats - Super Spec HP Acrylic Gloss Enamel #P28 (MPI Listed Product, Category 114) INTERIOR FINISH COATS A. Flat Finish: a. Two (2) Coats - Super Spec Alkyd Calcimine Recoater #306 (MPI Listed Product, Category 49). b. Two (2) Coats - Super Spec Sweep-Up Spray Production Alkyd Flat #150 c. Two (2) Coats - Super Spec Sweep-Up Spray Alkyd Flat #151 (MPI Listed Product, Category 55). d. Two (2) Coats- Benjamin Moore Collection Interior Alkyd Flat #204 (Canada e. Two (2) Coats- MooreStyle Interior Alkyd Flat #574 (Canada f. Two (2) Coats- Alkyd Ceiling Paint #259 (Canada

13 a. Two (2) Coats - Ultra Spec 500 Interior Flat Finish N536 (MPI Listed Product, Categories 53, 53-X Green) b. Two (2) Coats - Ultra Spec 500 Interior Low Sheen Finish N537 (MPI Listed Product, Categories 44, 44-X Green) c. One (1) or Two (2) Coats - Aura Waterborne Interior Matte Finish #522 (MPI Listed Product, Categories 53, 53-X Green) d. Two (2) Coats - Regal Premium Interior Matte Finish #221 (MPI Listed Product, Category 53). e. Two (2) Coats - Regal Premium Interior Flat Finish #215 (MPI Listed Product, Category 53). f. Two (2) Coats - Regal Select Flat Finish #547 (MPI Listed Product, Categories 53, 53 X-Green). g. Two (2) Coats - Regal Select Matte Finish #548 (MPI Listed Product, Categories 53, 53 X-Green) h. One (1) or Two (2) Coats - Aura Bath & Spa Matte #532. i. Two (2) Coats - Waterborne Ceiling Paint #508. j. Two (2) Coats - Natura 0 VOC Interior Latex Flat #512 (MPI Listed Product, Categories 53, 53-X Green, 143, 143-X Green). k. Two (2) Coats - Ben Interior Latex Flat #W625 (MPI Listed Product Categories 53, 53-X Green). l. Two (2) Coats - Eco Spec WB Interior Latex Flat # 373 (MPI Listed Product, Category 142). m. Two (2) Coats - Super Spec Latex Flat #275 (MPI Listed Product, Category 53). n. Two (2) Coats - Muresco Ceiling White #258. o. Two (2) Coats - Super Hide Latex Flat #282. p. Two (2) Coats - Super Spec Sweep - Up Spray Latex Flat #153 (MPI Listed Product, Categories 118, 133). q. Two (2) Coats - MooreStyle Interior Acrylic Latex Flat #564 (Canada B. Eggshell Finish: a. Two (2) Coats Dulamel Eggshell Enamel #C305. b. Two (2) Coats- MooreStyle Interior Alkyd Eggshell #575 (Canada a. Two (2) Coats Ultra Spec 500 Interior Eggshell Finish N538 (MPI Listed Product Categories 52, 52-X Green) b. Two (2) Coats - Aura Waterborne Interior Eggshell Finish #524 (MPI Listed Product Categories 44, 44-X Green, 138, 138-X Green) c. Two (2) Coats - Regal Classic Eggshell Finish #319 (MPI Listed Product, Categories 44, 52, 139). d. Two (2) Coats Regal Select Eggshell Finish #549 (MPI Listed Product, Categories 44, 44 X-Green, 138, 138 X-Green) e. Two (2) Coats - Natura 0 VOC Interior Latex Eggshell Finish #513 (MPI Listed Product, Categories 44, 44-X Green, 144, 144-X Green). f. Two (2) Coats ben Interior Latex Eggshell Finish #626 (MPI Listed Product, Categories 44, 44-X Green). g. Two (2) Coats - Eco Spec WB Interior Latex Eggshell Finish# 374 (MPI Listed Product, Categories 52, 52-X Green, 139, 145, 145-X Green). h. Two (2) Coats - Super Spec Latex Eggshell Enamel #274 (MPI Listed Product, Category 44). i. Two (2) Coats - Super Hide Latex Eggshell Enamel #286. j. One (1) Coat - Super Spec Acrylic Self-leveling Low Lustre # K249 (Canada Only)

14 k. Two (2) Coats - MooreStyle Interior Acrylic latex Eggshell #565 (Canada C. Satin/Semi-Gloss Finish: a. One (1) or Two (2) Coats Advance Waterborne Interior Alkyd Satin Finish #792 b. One (1) or Two (2) Coats Advance Waterborne Interior Alkyd Semi- Gloss Finish #793 c. Two (2) Coats - Satin Impervo #C235 (MPI Listed Product, Category 51) d. Two (2) Coats IronClad Alkyd Low Lustre Metal & Wood Enamel #C163 (MPI Listed Product, Category 79). e. Two (2) Coats - Super Spec Alkyd Semi-Gloss Enamel #C271 (MPI Listed Product, Category 51). f. Two (2) Coats Dulamel Alkyd Semi-Gloss Finish #C207 (MPI Listed Product, Category 47). g. Two (2) Coats- Melamine Low Luster Enamel #303 (Canada h. Two (2) Coats- MooreStyle Interior Alkyd Semi-Gloss #578 (Canada i. Two (2) Coats- MooreStyle Interior Alkyd Satin #577 (Canada j. Two (2) Coats- MooreStyle Interior Alkyd Pearl #576 (Canada a. Two (2) Coats Ultra Spec 500 Interior Semi-Gloss Finish N539 (MPI Listed Product Categories 43, 43-X Green) b. Two (2) Coats Ultra Spec 500 Interior Gloss Finish N540 (MPI Listed Product Categories 54, 54-X Green) c. Two (2) Coats - Aura Waterborne Interior Satin Finish #526 (MPI Listed Product, Categories 43, 43-X Green) d. Two (2) Coats - Regal Classic Pearl Finish #310 (MPI Listed Product, Category 43). e. Two (2) Coats Regal Select Pearl Finish #550 (MPI Listed Product, Categories 43, 43 X-Green, 140). f. Two (2) Coats - Regal Semi-Gloss Finish #333 (MPI listed Product, Category 54). g. Two (2) Coats Regal Select Semi-Gloss #551 (MPI Listed Product, Categories 54, 54-X Green). h. Two (2) Coats - Natura 0 VOC Interior Latex Semi-Gloss Finish #514 (MPI Listed Categories 54, 54-X Green, 147, 147-X Green). i. Two (2) Coats Ben Interior Latex Semi-Gloss Finish #W627 (MPI Product Categories 54, 54-X Green, 141, 141-X Green) j. Two (2) Coats - Eco Spec WB Interior Latex Semi-Gloss #376 (MPI Listed Product Categories 54, 54-X Green). k. Two (2) Coats - Waterborne Satin Impervo Low-Lustre Enamel Finish #314 (MPI Listed Product, Category 43). l. Two (2) Coats Kitchen & Bath 100% Acrylic Satin Finish #322. m. Two (2) Coats - Super Spec Latex Semi-Gloss Enamel #276. n. Two (2) Coats - Super Spec 100% Acrylic Semi-Gloss Enamel #281. o. Two (2) Coats - Super Spec Latex Pearl Finish #277 p. Two (2) Coats - Super Spec Masonry Acrylic Satin-Fil #172. q. Two (2) Coats - Super Hide Semi-Gloss Enamel Finish #283. r. Two (2) Coats - MooreStyle Interior Acrylic Latex Pearl #566 (Canada s. Two (2) Coats - MooreStyle Interior Acrylic Latex Semi - Gloss #568 (Canada 3. Epoxy:

15 a. Two (2) Coats - Super Spec Acrylic Epoxy #256/86. b. One (1) or Two (2) Coats - Super Spec HP Acrylic Epoxy Semi-Gloss Coating #P43/P43-84 (MPI Listed Product, Category 215). c. One (1) or Two (2) Coats - Super Spec Acrylic Epoxy Gloss P43/P43-86 D. High Gloss Finish: a. One (1) or Two (2) Coats Advance Waterborne Interior/Exterior Alkyd High Gloss #N794 (MPI Listed Product, Categories 157, 157 X-Green). b. Two (2) Coats- Benjamin Moore Collection High Gloss Enamel #133 (MPI Listed Product, Category 48) c. Two (2) Coats - Super Spec HP Urethane Alkyd Gloss #P22 (MPI Listed Product Categories 9, 48) d. Two (2) Coats - Porch & Floor Alkyd Enamel #C112. e. Two (2) Coats - Super Spec HP D.T.M. Alkyd Gloss #P26. f. Two (2) Coats - Moorcraft Super Spec HP DTM Alkyd Gloss Enamel #P26. g. Two (2) Coats- MooreStyle Interior/Exterior High Gloss Enamel #579 (Canada a. Two (2) Coats Ultra Spec 500 Interior Gloss Finish N540 (MPI Listed Product Categories 54, 54-X Green) b. Two (2) Coats Impervex Latex High Gloss Enamel #N309 (MPI Listed Product, Category 114). c. Two (2) Coats - Super Spec HP D.T.M. Acrylic Gloss Enamel #P28 (MPI Listed Product, Categories 114, 154). 3. Epoxy: a. Two (2) Coats - Super Spec Acrylic Epoxy #256/ b. Two (2) Coats - Super Spec HP Acrylic Epoxy Gloss #P43/P43-84 (MPI Listed Product, Category 215). PART 3 EXECUTION 3.1 EXAMINATION A. Do not begin installation until substrates have been properly prepared. B. Ensure that surfaces to receive paint are dry immediately prior to application. C. Ensure that moisture-retaining substrates to receive paint have moisture content within tolerances allowed by coating manufacturer. Where exceeding the following values, promptly notify Architect and obtain direction before beginning work. 1. Concrete and Masonry: 13 percent. Allow new concrete to cure a minimum of 28 days. 2. Exterior Wood: 17 percent. 3. Interior Wood: 15 percent. 4. Interior Finish Detail Woodwork, Including Trim, and Casework: 10 percent. 5. Plaster and Gypsum: 15 percent. 6. Concrete Slab-On-Grade: Perform calcium chloride test over 24 hour period or other acceptable test to manufacturer. Verify acceptable moisture transmission and ph levels. D. Examine surfaces to receive coatings for surface imperfections and contaminants that could impair performance or appearance of coatings, including but not limited to, loose primer, rust, scale, oil, grease, mildew, algae, or fungus, stains or marks,

16 cracks, indentations, or abrasions. E. Correct conditions that could impair performance or appearance of coatings in accordance with specified surface preparation procedures before proceeding with coating application. 3.2 PREPARATION - GENERAL A. Clean surfaces thoroughly prior to coating application. B. Do not start work until surfaces to be finished are in proper condition to produce finished surfaces of uniform, satisfactory appearance. C. Stains and Marks: Remove completely, if possible, using materials and methods recommended by coating manufacturer; cover stains and marks which cannot be completely removed with isolating primer or sealer recommended by coating manufacturer to prevent bleed-through. D. Remove Mildew, Algae, and Fungus using materials and methods recommended by coating manufacturer. E. Remove dust and loose particulate matter from surfaces to receive coatings immediately prior to coating application. F. Remove or protect adjacent hardware, electrical equipment plates, mechanical grilles and louvers, lighting fixture trim, and other items not indicated to receive coatings. G. Move or protect equipment and fixtures adjacent to surfaces indicated to receive coatings to allow application of coatings. H. Protect adjacent surfaces not indicated to receive coatings. I. Prepare surfaces in accordance with manufacturer's instructions for specified coatings and indicated materials, using only methods and materials recommended by coating manufacturer. 3.3 SURFACE PREPARATION A. Concrete and Concrete Masonry: Clean surfaces free of loose particles, sand, efflorescence, laitance, form oil, curing compounds, and other substances which could impair coating performance or appearance. B. Concrete Floors: Remove contaminants which could impair coating performance or appearance. Verify moisture transmission and alkaline-acid balance recommended by coating manufacturer; mechanically abrade surface to achieve grit medium-sandpaper texture. C. Existing Coatings: 1. Remove surface irregularities by scraping or sanding to produce uniform substrate for coating application; apply one coat primer of type recommended by coating manufacturer for maximum coating adhesion. 2. If presence of lead in existing coatings is suspected, cease surface preparation and notify Architect immediately. D. Gypsum Board: Repair cracks, holes and other surface defects with joint compound to produce surface flush with adjacent surfaces

17 E. Masonry Surfaces - Restored: Remove loose particles, sand, efflorescence, laitance, cleaning compounds and other substances that could impair coating performance or appearance. F. Metals - Aluminum, Mill-Finish: Clean and etch surfaces with a phosphoric acidwater solution or water based industrial cleaner. Flush with clean water and allow to dry, before applying primer coat. G. Metals - Copper: Clean surfaces with pressurized steam, pressurized water, or solvent washing. H. Metals - Ferrous, Unprimed: Remove rust or scale, if present, by wire brush cleaning, power tool cleaning, or sandblast cleaning; remove grease, oil, and other contaminants which could impair coating performance or appearance by solvent cleaning, with phosphoric-acid solution cleaning of welds, bolts and nuts; spot-prime repaired welds with specified primer. I. Metals - Ferrous, Shop-Primed: Remove loose primer and rust, if present, by scraping and sanding, feathering edges of cleaned areas to produce uniform flat surface; solvent-clean surfaces and spot-prime bare metal with specified primer, feathering edges to produce uniform flat surface. J. Metals - Galvanized Steel (not passivated): Clean with a water-based industrial strength cleaner, apply an adhesion promoter followed by a clean water rinse. Alternately, wipe down surfaces using clean, lint-free cloths saturated with xylene or lacquer thinner; followed by wiping the surface dry using clean, lint-free cloths. K. Metals - Galvanized Steel, Passivated: Clean with water-based industrial strength cleaner. After the surface has been prepared, apply recommended primer to a small area. Allow primer to cure for 7 days, and test adhesion using the "cross-hatch adhesion tape test" method in accordance with ASTM D If the adhesion of the primer is positive, proceed with a recommended coating system for galvanized metal. L. Metals - Stainless Steel: Clean surfaces with pressurized steam, pressurized water, or water-based industrial cleaner. M. Plaster: Repair cracks, holes and other surface defects as required to maintain proper surface adhesion. Apply patching plaster or Joint compound and sand to produce surface flush with adjacent undamaged surface. Allow a full cure prior to coating application as recommended by the patching compound manufacturer's recommendations. N. Polyvinyl Chloride (PVC) Pipe: remove contaminants and markings with denatured alcohol scuff sand and wipe with solvent for maximum adhesion. Test adhesion before starting the job. O. Fiberglass Doors - remove contaminants with cleaning solvent (alcohol) scuff sand and wipe. Test adhesion of primer before starting job. P. Textiles - Insulated Coverings, Canvas or Cotton: Clean using high-pressure air and solvent of type recommended for material. Q. Wood: 1. Seal knots, pitch streaks, and sap areas with sealer recommended by coating manufacturer; fill nail recesses and cracks with filler recommended by coating manufacturer; sand surfaces smooth

18 2. Apply primer coat to back of wood trim and paneling. R. Wood Doors: Seal door tops and bottoms prior to finishing. S. Wood Doors - Field-Glazed Frames and Sash: Prime or seal glazing channels prior to glazing. 3.4 APPLICATION - GENERAL A. Apply each coat to uniform coating thickness in accordance with manufacturer's instructions, not exceeding manufacturer's specified maximum spread rate for indicated surface; thins, brush marks, roller marks, orange-peel, or other application imperfections are not permitted. B. Allow manufacturer's specified drying time, and ensure correct coating adhesion, for each coat before applying next coat. C. Inspect each coat before applying next coat; touch-up surface imperfections with coating material, feathering, and sanding if required; touch-up areas to achieve flat, uniform surface without surface defects visible from 5 feet (1.5 m). D. Remove dust and other foreign materials from substrate immediately prior to applying each coat. E. Where paint application abuts other materials or other coating color, terminate coating with a clean sharp termination line without coating overlap. F. Where color changes occur between adjoining spaces, through framed openings that are of same color as adjoining surfaces, change color at outside stop corner nearest to face of closed door. G. Re-prepare and re-coat unsatisfactory finishes; refinish entire area to corners or other natural terminations. 3.5 CLEANING A. Clean excess coating materials, and coating materials deposited on surfaces not indicated to receive coatings, as construction activities of this section progress; do not allow to dry. B. Re-install hardware, electrical equipment plates, mechanical grilles and louvers, lighting fixture trim, and other items that have been removed to protect from contact with coatings. C. Reconnect equipment adjacent to surfaces indicated to receive coatings. D. Relocate to original position equipment and fixtures that have been moved to allow application of coatings. E. Remove protective materials. 3.6 PROTECTION A. Protect completed coating applications from damage by subsequent construction activities. B. Repair to Architect's acceptance coatings damaged by subsequent construction activities. Where repairs cannot be made to Architect's acceptance, re-apply finish

19 coating to nearest adjacent change of surface plane, in both horizontal and vertical directions. END OF SECTION