COMPOSITE MATERIALS HANDBOOK. Volume. Structural Sandwich. Composites

Transcription

1 COMPOSITE MATERIALS HANDBOOK Structural Sandwich Volume 6 Composites

2 TABLE OF CONTENTS Page FOREWORD... ii CHAPTER 1 GENERAL INFORMATION INTRODUCTION TO THE HANDBOOK OVERVIEW OF HANDBOOK CONTENT INTRODUCTION NOMENCLATURE AND DEFINITIONS Loads, geometry, and material properties Subscripts Superscripts Assumptions and definitions System of units... 9 REFERENCES CHAPTER 2 GUIDELINES FOR PROPERTY TESTING INTRODUCTION DATA REDUCTION AND PRESENTATION EVALUATION OF CORE MATERIALS Introduction Mechanical properties Environmental effects Test methods EVALUATION OF CORE-TO-FACE SHEET BONDS Introduction Mechanical properties Environmental effects Test Methods EVALUATION OF FACE SHEET PROPERTIES Introduction Mechanical properties Environmental effects Test methods EVALUATION OF SANDWICH PANELS Introduction Mechanical properties Environmental effects Damage resistance Damage tolerance Repair Test methods EVALUATION OF INSERTS AND FASTENERS Introduction Environmental effects Test methods Mechanical properties EVALUATION OF OTHER FEATURES Introduction Mechanical properties Environmental effects iv

3 2.8.4 Test methods REFERENCES CHAPTER 3 MATERIAL DATA CORES Description of cores Core specifications Honeycomb Cores Cross-banded core Corrugated core Waffle-type core Foam cores Wood cores Core properties Estimation of core properties FACE SHEETS Description of face sheets Adhesively-bonded pre-fabricated face sheets Co-cured or co-bonded face sheets with adhesive Self-adhesive face sheets Face sheet properties ADHESIVES Description of adhesives Adhesive specifications Adhesive forms/types and uses Resins from self-adhesive face sheets Film adhesives Paste adhesives Liquid resins Foaming adhesives Adhesive chemistries Epoxy Bismaleimide Phenols Polyester Polyimide Adhesive properties REFERENCES CHAPTER 4 DESIGN AND ANALYSIS OF SANDWICH STRUCTURES INTRODUCTION DESIGN AND CERTIFICATION Basic design principles Design process Aircraft damage tolerance CERTIFICATION Introduction to certification issues Approach to certification testing Analysis validation Conformity oversight Nondestructive testing (NDT) Documentation requirements Continued airworthiness SANDWICH PANEL FAILURE MODES v

4 4.5 STIFFNESS AND INTERNAL LOADS Beam stiffness analysis Plate stiffness analysis Combined transverse and in-plane loadings Face sheet internal loads LOCAL STRENGTH ANALYSIS METHODS Face sheet failure Core shear Flatwise tension and compression Flexural core crushing Intracell buckling (dimpling) Sandwich having cellular (honeycomb) core Sandwich having corrugated core Shear intracell buckling Combined compression and shear intracell buckling Face sheet wrinkling Wrinkling of sandwich face sheets under edgewise load Sandwich with core supporting face sheets continuously Sandwich with honeycomb core Shear face sheet wrinkling Face sheet wrinkling - combined loads Face sheet wrinkling - curved panels Core shear crimping Attachments and hard points Design of flat circular sandwich panels loaded at an insert FLAT PANEL INTERNAL LOADS AND STRESSES - PRESSURE LOADING Design of flat rectangular sandwich panels under various normal loadings Design of flat sandwich panels under uniformly distributed normal load Determining face sheet thickness, core thickness, and core shear modulus for simply supported flat rectangular panels under uniform load Use of design charts Determining core shear stress Checking procedures Determining face sheet thickness, core thickness, and core shear modulus for simply supported flat circular panels under uniform load Use of design charts Determining core shear stress Checking procedure CURVED SANDWICH PANEL INTERNAL LOADS AND STRESSES General equations and analysis method FLAT PANEL STABILITY ANALYSIS METHODS Buckling of flat rectangular sandwich columns Design of flat rectangular sandwich panels under edgewise compression load Determining face sheet thickness Determining core thickness and core shear modulus Determining minimum value of d Determining actual value of d Checking procedure for determining buckling stress, F cr Design of flat rectangular sandwich panels under edgewise shear load Determining face sheet thickness Determining core thickness and core shear modulus Determining minimum value of d vi

5 Determining actual value of d Checking procedure for determining buckling stress, F cr Design of sandwich strips under torsion load Determining face sheet thickness, core thickness and core shear modulus for sandwich strips of trapezoidal and rectangular cross section Determining minimum values of d and t Determining actual values of d and t Checking procedure for sandwich strips of trapezoidal and rectangular cross section Determining face sheet thickness and core shear modulus for sandwich strips of triangular cross section Determining minimum value of t Determining actual value of t Checking procedure for sandwich strips of triangular cross section Design of flat rectangular sandwich panels under edgewise bending moment Determining face sheet thickness Determining core thickness and core shear modulus Determining minimum value of d Determining actual value of d Checking procedure for determining buckling stress, F cr DESIGN OF FLAT RECTANGULAR SANDWICH PANELS UNDER COMBINED LOADS Combined load buckling Biaxial compression Bending and compression Compression and shear Bending and shear Combined in-plane and transverse loads DESIGN OF SANDWICH CYLINDERS Introduction Sandwich cylinders under external radial pressure Determining face sheet thickness, core thickness, and core shear modulus for sandwich cylinders under external radial pressure Final design Sandwich cylinders under torsion Determining face sheet thickness for sandwich cylinders under torsion Determining core thickness and core shear modulus for sandwich cylinders under torsion Check to determine whether sideways buckling will occur Sandwich cylinders under axial compression or bending Determining face sheet thickness, core thickness, and core shear modulus Checking procedure for determining cylinder wall buckling stress, F cr Check to determine whether column buckling will occur Sandwich cylinders under combined loads Axial compression and external lateral pressure Axial compression and torsion Torsion and lateral external or internal pressure FINITE ELEMENT MODELING OF SANDWICH STRUCTURE Introduction Global models vii

6 Layered models Solid models Sandwich element models OPTIMUM SANDWICH Sandwich weight Sandwich bending stiffness Sandwich bending moment capacity Sandwich panel buckling REFERENCES CHAPTER 5 FABRICATION OF SANDWICH STRUCTURES (MATERIALS AND PROCESSES) INTRODUCTION MATERIALS Cores Face sheets Adhesives Surfacing and sealing PROCESSES Core Cleaning Drying Forming Splicing Potting Septums Core stabilization for machining Machining Tolerances Face sheets - co-cure vs. pre-cure and resin pressure Adhesive Impression check Bonding Filleting HONEYCOMB CORE CRUSH Core crush during cure Core crush - theoretical discussion Core crush stabilization for cure Core material characteristics and core crush Prepreg and adhesive material characteristics and core crush Cure cycles and core crush QUALITY ISSUES INCLUDING NONDESTRUCTIVE EVALUATION (NDI) REFERENCES CHAPTER 6 QUALITY CONTROL INTRODUCTION MATERIAL PROCUREMENT QUALITY ASSURANCE PROCEDURES Specifications and documentation Receiving inspection PART FABRICATION VERIFICATION Process verification Nondestructive inspection Destructive tests STATISTICAL PROCESS CONTROL MANAGING CHANGE IN MATERIALS AND PROCESSES... 4 viii

7 REFERENCES... 5 CHAPTER 7 SUPPORTABILITY INTRODUCTION DESIGN FOR SUPPORTABILITY In-service experience Inspectability Material selection Damage resistance Environmental compliance Reliability and maintainability Repairability SUPPORT IMPLEMENTATION Part inspection Damage assessment Repair design criteria Repair of composite structures Damage removal and site preparation Bonded repairs Repair analysis Repair procedures Repair inspection Repair validation LOGISTICS REQUIREMENTS REFERENCES Index... 1 ix