GUIDE SPECIFICATION EXETER SECURITY SHIELD SECURITY WINDOW BARRIER SYSTEM
|
|
- Catherine Griffith
- 6 years ago
- Views:
Transcription
1 1 GUIDE SPECIFICATION EXETER SECURITY SHIELD SECURITY WINDOW BARRIER SYSTEM 1.01 WORK INCLUDED PART 1: GENERAL A. Provide for all labor, equipment, materials and services to furnish and install SECURITY SHIELD Window Barriers and correlated components as specified herein and as shown on the drawings RELATED WORK A. Section Aluminum Entrance and Storefronts B. Section Aluminum Windows C. Section Wood Windows D. Section Glass & Glazing 1.03 REFERENCES A. ASCE 7-88 B. ANSI A58.1 C. ASTM E 330 D. Protocol TAS 201,202, 203 (Miami-Dade) E. ANSI/SMA TESTING AND PERFORMANCE REQUIREMENTS A. Test Units 1. SECURITY SHIELD Level 1 & 2 units Test shall meet or exceed the criteria set forth by ANSI/SMA 2 SECURITY SHIELD Level 3, 4, 5 & 6 Tests unless otherwise noted shall conform to the impact, static, and cyclical test as set forth by the Dade County Building Code Compliance Office Protocols TAS-201, 202, and 203 for SECURITY SHIELD Level 3 and above. B. Test Procedures and Performance - 1. Window barriers shall conform to criteria for conducting impact, static and cyclic tests as required by Sections 2315 and of the South Florida Building Code and Protocol TAS 201, 202, and Impact Test TAS 201. a. Missile impact barrier with a solid S43 nominal 2 x 4, #2 surface dry, Southern Pine of not less than 7 ft. in length and 9 lbs. in weight at a velocity of not less than 50 ft/sec without specimen failure. (Level 3)
2 2 b. Missile impact barrier with a solid S43 nominal 2 x 4, #2 surface dry, Southern Pine of not less than 7ft. in length and 9 lbs. In weight at a velocity of not Less than 80 ft./sec without specimen failure. (Level 4) c. Missile impact barrier/shutter with a nominal 2 x 4 of not less than 15 lbs. In weight a velocity of not less than 80 ft./sec ( Levels 5 & 6 pertains to stainless perforated barrier material listed in section 2.01.C2) Essential facilities protection specification. 3. Uniform Static Air Pressure Test - TAS 202 a. Apply one-half full test load and full test load for 30 seconds at P-Max both inward and outward with out failure. b. Specified design pressure (DP) should not be less than 120 PSF, unless noted. 4. Cyclic Wind Pressure Loading Test - TAS 203 a. Apply loads to the specimen using the cycles specified in Section Table 23F and/or 2315 Table 1 of the South Florida Building Code without failure. b. Specified design pressure (DP) should not be less than 120 PSF, except where noted. B. 24 Hour Protection 1. Units must provide security protection as well as approved protection from wind. 2. Security and Hurricane protection must be in place 24 hours per day. Product will not be accepted if it has to be put in place, rolled down, or in any way prepared in the event of an emergency. C. Emergency Egress 1. Units so designated must have emergency egress option. Emergency egress option must use EAP model #.25SS latch, or EAP model #100 Panic Release Latch, positive engagement. Option may be automatically operated in accord with existing window action if required. (Levels 2 and above) 2. Units so designated must meet egress requirements set forth by NFPA (National Fire Prevention Association) 101 B. D. Sun Control 1. The window barrier system to have a shading coefficient of The window barrier system will have the ability to reduce solar heat gain by an estimated 50%. 3. The above requirements must be certified by an approved independent solar testing facility.
3 3 E. E.M.I. Shielding Effectiveness 1. The shutter system to have a shielding effectiveness per the Dash, Straus & Goodhue study. 2. The shutter system shall have a shielding effectiveness of a least 93.69% attenuation effectiveness, when a tightly sealed electrical contact is made. 3. The shutter system shall have a shielding effectiveness of 24dB attenuation effectiveness, when a tight electrical seal is made QUALITY ASSURANCE A. All components must be assembled / manufactured at an ISO certified facility SUBMITTALS A. Shop Drawings 1. Manufacturer shall supply completed shop drawings, location, diagrams and necessary details and erection notes to insure a proper installation. B. Samples 1. Submit samples of each required aluminum and steel finishes. 2. Submit additional samples as may be directed by the architect. C. Test Reports 1. Provide certified independent laboratory test reports verifying compliance with requirements in Section DELIVERY, STORAGE AND HANDLING A. Handle and store shutters and accessories in strict compliance with the manufacturer s specific instructions WARRANTIES A. Security Window Barriers 1. Materials for the above project will be free from factory defects in materials and workmanship for a three (3) year limited warranty. 2. The contractor shall assume the full responsibility for one year on the proper usage, design, handling, installation and anchorage as it relates to the structural attachment as outlined on the approved shop drawings and specifications.
4 4 PART 2: PRODUCTS 2.01 Materials A. Acceptable Security Screen Window Manufacturers EXETER ARCHITECTURAL PRODUCTS INC. Series Security Shield 243 W. Eighth Street Wyoming PA or Fax: B. Aluminum 1. Extruded aluminum shall be 6063-T5 alloy and temper. 2. Nominal wall thickness for primary frame extrusions shall be a minimum of Frame profile shall be thin, not exceeding a maximum frame width of 1.375, to preserve architectural integrity of building and window openings. C. Steel / Infill 1. Galvanealed steel sheet shall be of 950 XK Structural Steel. Mill finish quality, domestic quality. Material certification required. 2. Stainless Steel sheet shall be 304-2b Prime conforming to ASTM-A Perforated metal sheet shall be of not less than 16 gauge (Levels 1 & 2) and 14 gauge (Levels 3 through 6) galvanealed or stainless steel sheet. 4. Perforated pattern shall be InvisiPerf#1 or TXL 22 (Level 1) InvisiPerf #2 or TXL-23 Levels 2 through 6). Perforated sheet barrier pattern shall consist of staggered round holes, not to exceed 3/16 in diameter. Straight line hole patterns shall not be accepted. 5. Hole burrs on underside shall be minimal and not exceed.006 to maintain smoothness of sheet. 6. Perforated metal sheet shall have not less than 63% (Level 1) and 51% (all other levels) open air. 7. Stainless steel wire cloth shall be 12 x 12 mesh.028 diameter wire. D. Hardware 1. Security latch system shall be Security Egress Options Model #EAP-25SS DM-25or EAP model #100 Panic Release Latch. 2. Security latch system shall be single point release. E. Anchors and Anchor Fasteners 1. Concealed and non-concealed anchors and anchor fasteners may be of aluminum, stainless steel (300 series type), cadmium, zinc, nickel plated steel, brass and hot dipped galvanized. Non-treated corrosive fasteners are strictly prohibited.
5 5 F. Security Beads 1. The security glazing bead for perforated barrier shall be of finished.080 extruded aluminum not less than 1 in width, running the full perimeter of the inside master frame. 2. Extrusions must be double hollow configuration and must be 6063-T5. 3. Glazing legs shall be mechanically fastened with #10 self tapping fasteners, 5/8 in length, vertically and horizontally on 6 centers and be concealed for service maintenance only. G. Optional Bug Screen x 16 Fiberglass Mesh Bug Screen installed at customer request. 2 Must be pulled tight to perforated metal infill to prevent damage, rips, tears, etc to the bug screen. 3. Secured with.187 spline. 4. Installed by manufacturer or in the field by installer using a Screen Spline Installation Tool FABRICATION A. General 1. Depth of frame shall not be less than Horizontal and vertical site lines shall be equal and not exceed 2. B. Frame 1. Frame joints shall be neatly mitered to form a hairline joint. Corners shall be reinforced with a solid.062 extruded 3/4 x 3/4 x 1 minimum aluminum corner key and welded to afford maximum rigidity. Mechanical crimping, gluing or cold welding shall not be permitted. C. Finish - Aluminum (Select Organic or Anodic) 1. ORGANIC - Finish all exposed areas of aluminum framing and components in accordance with AAMA or DESIGNATION DESCRIPTION AAMA SPEC AA-M12-C41-RIX Polycron III AA-M12-C41-RIX Kynar Based *Color to be selected by architect. 2. ANODIC - Finish all exposed areas of aluminum framing and components in accordance with AAMA DESIGNATION CLASS DESCRIPTION AAMA SPEC AA-M12-C22-A41 I Clear Anodized D. Finish - Perforated Galvanealed Steel Sheet 1. Primary finish to mill steel sheet shall be a heat treated galvanealed A40 prime coating without spangles. 2. Finish coat shall consist of weather resistant high performance electrostatic applied coating from 2.5 to 3.4 mills and baked to a smooth finish.
6 6 DESIGNATION CLASS DESCRIPTION AAMA SPEC A40 Prime Galvanealed ASTM A642 *Color to be selected by architect. E. Finish - Perforated Stainless Steel Sheet 1. Corrosion resistant low carbon series 304-2B stainless steel. 2. Finish Coat shall consist of weather resistant high performance electrostatic applied coating from 2.5 to 3.4 mills and baked to a smooth finish. DESIGNATION CLASS DESCRIPTION SPEC 304-2B Prime Stainless ASTM A240
7 7 PART 3: EXECUTION 3.01 INSPECTION A. Job Conditions 1. Verify that openings are dimensionally within allowable tolerances, plumb, level and clean. Provide a solid anchoring surface in accordance with approved shop drawing INSTALLATION A. Use only skilled tradesmen with work done in accordance with approved shop drawing and specifications. B. Plumb and align shutters in a single plane for each wall frame and erect shutters and material square and true, adequately anchored to maintain positions permanently when subjected to normal thermal and building movement and specified wind loads. END OF SECTION EXETER ARCHITECTURAL PRODUCTS, INC. 243 West Eighth Street 3251 S. W. Island Way Wyoming PA Palm City FL (Fax) (Fax)
GUIDE SPECIFICATION EXETER VERSA SHIELD SECURITY SCREEN SYSTEM
1 GUIDE SPECIFICATION EXETER VERSA SHIELD SECURITY SCREEN SYSTEM 1.01 WORK INCLUDED PART 1: GENERAL A. Provide for all labor, equipment, materials, and services to furnish and install VERSA SHIELD Window
More informationMPG Series 2250T Thermally Broken Aluminum Window
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2250T Thermally Broken Aluminum Window PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows complete with hardware
More informationSERIES SA30 STEEL/ALUMINUM FIXED DETENTION WINDOWS SECTION 08651
SERIES SA30 STEEL/ALUMINUM FIXED DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows as
More informationSeries B450 Guide Specification
Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com STOREFRONT SERIES B450 Shear Block Air Infiltration:
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 4113 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Aluminum entrance doors and frames. 2. Glass infill panels. 3. Door hardware. B. Related Sections:
More informationTender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Extruded aluminum windows with fixed sash..2 Factory glazed..3 Perimeter sealant. 1.2 RELATED SECTIONS.1 Section 05500 - Metal Fabrications.2
More informationArchitectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION
Architectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION Section 08520 Aluminum Windows PART 1: WORK INCLUDED A. The conditions of the contract and applicable sections of Division
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 - GENERAL 1.01 SUMMARY A. Section includes: 1. Storefront systems and aluminum framed glass doors. 2. Hardware, fasteners, accessories, filler pieces, etc., required
More informationSERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651
SERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows
More informationMPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows
More informationHeavy Commercial / Architectural Projected Windows Series L900T AW150
Heavy Commercial / Architectural Projected Windows Series L900T AW150 Section 08520...Aluminum Windows PART 1: WORK INCLUDED GUIDE SPECIFICATION A. The conditions of the contract and applicable sections
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS 1. PART 1 GENERAL 1.1 WORK INCLUDED: 1. Provide labor, material, equipment and services to furnish and install aluminum windows shown on drawings and specified herein. Window
More informationSILVER LINE BUILDING PRODUCTS. Series 1700 Heavy Commercial Aluminum Double Hung. HC65 48 x84 / HC50 60 x96 Replacement Window
DIVISION 08 / SECTION 08505 METAL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: GENERAL Series 1700 Heavy Commercial Aluminum Double Hung 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE
More informationSECTION / / BULLET RESISTANT SOUND CONTROL WINDOWS
SECTION 08381 / 088856 / 085673 BULLET RESISTANT SOUND CONTROL WINDOWS 1.0 GENERAL 1.1 DESCRIPTION OF WORK A. Furnish and install FACTORY PREGLAZED Bullet Resistant Sound Control Windows specified herein
More informationImpact-Resistant Entrances Series
ARCHITECTURAL PRODUCTS Impact-Resistant Entrances Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES
More informationSECTION U.S. ALUMINUM SERIES BAL-350 HURRICANE RESISTANT BALCONY/TERRACE DOOR
Page 1 of 6 SECTION 08 39 80 U.S. ALUMINUM SERIES BAL-350 HURRICANE RESISTANT BALCONY/TERRACE DOOR U.S. Aluminum has designed one of the most demanding air and water protection products, the BAL- 350 Small
More informationUnited Window & Door - Series 5500 New Construction Double Hung Windows Specifications
United Window & Door - Series 5500 New Construction Double Hung Windows Specifications Part 1 GENERAL 1.01 INCLUSIONS 1. All windows as called for in this specification will be furnished with all necessary
More informationCOVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY)
COVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (DOOR ASSEMBLY)
More informationSECTION STAINLESS STEEL WALL PANELS
SECTION 07400 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Dry joint, Rainscreen stainless steel wall panel system. 2. Accessories including attachments, clips, sub girts, shims, and fasteners 3.
More informationSECTION HVAC GRAVITY VENTILATORS
SECTION 23 37 23 HVAC GRAVITY VENTILATORS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSignature Series 5 Lap SECTION ALUMINUM WINDOWS
Signature Series 5 Lap SECTION 08 51 13 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Documents: Conditions of the Contract, Division 1 - General Requirements, and Drawings apply to Work of this
More informationFL200 13/4 x41/2 GUIDE SPECIFICATION. Non-Thermal Storefront
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide
More informationSECTION METAL FRAMED SKYLIGHT. A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system.
SECTION 08625 METAL FRAMED SKYLIGHT PART 1 GENERAL 1.01 SECTION INCLUDES: A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system. B. Fabrication
More informationDivision 8 Section "Flush Wood Doors" for louvers in wood doors. Division 15 Sections for louvers that are a part of mechanical equipment.
0 0 0 0 0 SECTION 000 - LOUVERS AND VENTS PART GENERAL RELATED DOCUMENTS EASTLAKE FIRE STATION REPLACEMENT HILLSBOROUGH COUNTY CIP # Drawings and general provisions of the Contract, including General and
More informationFL550 21/2 x5 GUIDE SPECIFICATION. Impact-Resistant Storefront
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide
More informationSECTION DETAILS (MECHANICALLY ASSEMBLY)
COVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (DOOR ASSEMBLY)
More informationCTB Commercial Aluminum Window
Technical Information Description The is thermally-broken for use in commercial construction. Basic models include horizontal slider, single hung and fixed picture windows. Units are mulled together with
More informationMARLIN WINDOWS, INC 3500 HC SERIES 3 3 8" SLIDING WINDOW PAGE 1
PAGE 1 SPECIFICATIONS GENERAL Sliding windows shall be Marlin series #3500-HC (thermally improved) as manufactured by Marlin windows, and shall conform to ANSI/AAMA 101-88 HS-HC40. Series #3500 shall have
More informationSILVER LINE BUILDING PRODUCTS
DIVISION 08 / SECTION 08560, VINYL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: 2200/2300/2600 Vinyl Single Hung Windows R50/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2.
More informationSECTION EZ-SLIDE 80 AND 180 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
Page 1 of 6 SECTION 08 32 20 EZ-SLIDE 80 AND 180 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationSeries 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
More informationHORIZONTAL SLIDER SERIES 700. Main Frame Depth: 2 3/4 Glazing Thickness (Maximum): 5/8 Thermal Break:
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 700 Main
More informationCardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS
Cardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide specification has been developed using
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 GENERAL 1.1 SECTION INCLUDES A. Projected windows. B. Fixed windows. 1.2 RELATED SECTIONS A. Section 07900: Joint Sealers. B. Section 08400: Entrances and Storefronts.
More informationSECTION CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
Page 1 of 6 SECTION 08 32 20 CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS [OR WOOD] PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 08 51 69.11 ALUMINUM STORM WINDOWS SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. 2. Also delete any other item or paragraph not applicable
More informationSeries 2900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 2900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
More informationSeries 8100 Horizontal Slider HS-C x 1524 ( 71 x 60 )
1.01 GENERAL PROVISIONS: PART 1 - GENERAL A. The Conditions of the Contract, and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work with that of all construction contractors
More informationSECTION ALL GLASS ENTRANCES. 1. Lock cylinders for tempered glass entrance doors are specified in Division 8 section Finished Hardware.
1 SECTION 08 4210 ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1. Lock cylinders
More informationSECTION HANDRAILS AND RAILINGS. A. Section Cast-In-Place Concrete; coordination with substrate.
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Welded stainless steel railing systems. 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place Concrete; coordination with substrate.
More informationSECTION MISCELLANEOUS METALS
PART 1 GENERAL 1.1 WORK OF THIS SECTION A. Contractor shall provide all labor, materials, equipment and incidentals as shown, specified and required to furnish and install all miscellaneous metal fabrications
More informationModel 2000 Single Hung H-HC x 2515 (60 x 99 )
Architect to edit the items in red. PART 1 - GENERAL 1.01 GENERAL PROVISIONS: A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work
More informationFL550T 21/2 x5. GUIDE SPECIFICATION Series FL550T Thermal (21/2 x 5 ) Impact-Resistant Storefront. Thermal Impact-Resistant Storefront
Series FL550T Thermal (21/2 x 5 ) Impact-Resistant Storefront Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410
More information[Project Name] Section [ ]
Page 1 PART 1 - GENERAL 1.1 SECTION INCLUDES 1.1.1 Design, labor, products, equipment and services necessary for interior/exterior Aluminum Facade System (AFS) work, in accordance with the Contract Documents.
More informationSECTION CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
SECTION 08 32 20 CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS Page 1 of 6 USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationSECTION EXTERIOR GRILLS AND SCREENS
SECTION 10 82 13 PART 1 GENERAL PART 1 1 SUMMARY A. Section Includes: 1. Exterior perforated aluminum screen wall system with Ombrae TM Optical Tile imaging technology. 2. Accessories including attachments,
More informationSECTION STEEL WINDOWS UL Labeled Fire-Rated Horizontal Slider (900) Use Tools / Options / View / Hidden Text to view hidden notes and edit.
SECTION 08510 STEEL WINDOWS UL Labeled Fire-Rated Horizontal Slider (900) Use Tools / Options / View / Hidden Text to view hidden notes and edit. PART 1 GENERAL 1.1 SECTION INCLUDES A. Fire Rated Steel
More informationSECTION ALUMINUM-FRAMED HIGH PERFORMANCE THERMAL ENTRANCE DOORS
PART 1 GENERAL SECTION 08 1116 ALUMINUM-FRAMED HIGH PERFORMANCE THERMAL ENTRANCE DOORS 1.01 SECTION INCLUDES A. Aluminum-framed storefront, with vision glass. B. Infill panels of glass. C. Aluminum doors
More informationSECTION METAL WALL PANEL SYSTEM
CSI Format for Metal Wall Panel System Specification SECTION 07410 METAL WALL PANEL SYSTEM PART 1 GENERAL 1.1 SECTION INCLUDES A. Exterior Metal Plate Wall Panels B. Substructure and Framing C. Structural
More informationSECTION RADIO FREQUENCY SHIELDING ENCLOSURE RF Modular Pan System
SECTION 13096 RADIO FREQUENCY SHIELDING ENCLOSURE RF Modular Pan System Prepared by: 90 Dayton Avenue, Unit 4B, Suite 13 Passaic, NJ 07055 (973) 574-9077 13096-1 RF MODULAR PAN SYSTEM PART 1 GENERAL 1.1
More informationSECTION ARCHITECTURAL GLASS HANDRAIL AND RAILINGS 3-Line Glass Rail Railing Spec
SECTION 05720 ARCHITECTURAL GLASS HANDRAIL AND RAILINGS 3-Line Glass Rail Railing Spec PART 1 - GENERAL 1.01 WORK INCLUDED A. Furnish and install [aluminum] railings and components. 1.02 REFERENCE A. American
More information6400 Series TRIPLE GLAZED THERMAL BREAK CHURCH WINDOWS America's finest custom windows MINIMUM 5 8" AIR SPACE 3 1 2" SCALE = FULL SIZE
Since 906 Series The Series is a heavy triple glazed church window incorporated into a " thermally broken frame. The thermal break is achieved with the use of Thermal Strip technology. Two different aluminum
More informationSERIES /8 HORIZONTAL SLIDING WINDOW (CW30)
SERIES 525 2-5/8 HORIZONTAL SLIDING WINDOW (CW30) I. GENERAL: SPECIFICATIONS Scope of Work - Furnish all necessary materials, labor and equipment for the complete installation of aluminum windows for this
More informationModel 8000 Double Hung H-C x 2311 (56 x 91 )
1.00 GENERAL PROVISIONS: PART 1 - GENERAL A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work with that of all construction contractors
More informationA. Section Cast-In-Place Concrete: Openings in cast-in-place concrete.
Euro Vista Multi Slide Impact Rated Multi Slide Door PART 1 GENERAL 1.1 SECTION INCLUDES A. Sliding/Folding Doors. 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place Concrete: Openings in cast-in-place
More informationSECTION SERIES ALL GLASS ENTRANCES
1 SECTION 08 4210 1200 SERIES ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1.
More informationModel 2000 IM Single Hung H-HC x 2500 (60 x 96 )
1.00 GENERAL PROVISIONS: PART 1 - GENERAL A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work with that of all construction contractors
More informationSECTION FOLDING ALUMINUM FRAMED WALL SYSTEM
SECTION 08417 FOLDING ALUMINUM FRAMED WALL SYSTEM PART 1 GENERAL 1.1 SUMMARY A. Section includes: 1. Folding aluminum framed door system. 2. Door hardware. 3. Glass. 1.2 SYSTEM DESCRIPTION A. Aluminum-framed
More informationLOG COLLEGE MIDDLE SCHOOL
PART 1-GENERAL 1.1 SUMMARY A. This section includes the following: 1. Curb-mounted plastic glazed skylights. B. Refer to roofing system sections for roofing accessories to be built into the roofing system
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 08 51 69.11 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More informationSECTION / STC 52 METAL SOUND CONTROL DOORS
SECTION 08 34 73 / 08 34 73.13 STC 52 METAL SOUND CONTROL DOORS PART 1 GENERAL 1.1 RELATED DOCUMENTS: A. Drawings and general provisions of the Contract, including general and Supplementary Conditions
More informationSECTION ALUMINUM HANDRAIL SYSTEMS
SECTION 05520 ALUMINUM HANDRAIL SYSTEMS PART 1 - GENERAL 1.01 SUMMARY A. Section includes aluminum handrails and railings. B. Related Work: 1. Section 03300 - Cast-in-Place Concrete C. References: 1. American
More informationT700 SERIES(AW50)-Impact (Formerly 8050 series) SINGLE HUNG 3 1/4 FRAME DEPTH (SIDE LOAD)
T700 SERIES(AW50)-Impact (Formerly 8050 series) SINGLE HUNG 3 1/4 FRAME DEPTH (SIDE LOAD) FEATURES 1.) Available Configurations -Single hung -Oriel style (optional) 2.) Main frame / Sash -Drop-in glazing
More informationSECTION ORNAMENTAL ALUMINUM RAILING
SECTION 05730 ORNAMENTAL ALUMINUM RAILING PART 1 GENERAL 1.1 SECTION INCLUDES A. Aluminum Pipe Railing 1.2 RELATED SECTIONS A. Section 03300 Cast-In-Place Concrete: Placement of sleeves cast in concrete.
More informationA. Access doors and frames are part of an access door and frame allowance.
SECTION 08 31 13 ACCESS DOORS AND FRAMES PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION VINYL (PVC) WINDOWS
SECTION 085313 VINYL (PVC) WINDOWS SERIES 3000/3900 NEW CONSTRUCTION DOUBLE HUNG PART 1 GENERAL 1.01 SECTION INCLUDES A. All windows of the types and sizes called for in this specification shall be furnished
More informationK. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.
DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:
More informationSECTION COMPOSITE WALL PANELS PART 1 GENERAL 1.01 SECTION INCLUDES
SECTION 07 4243 - PART 1 GENERAL 1.01 SECTION INCLUDES A. Composite wall panel system consisting of aluminum-faced composite panels in a rainscreen application as part of the assembly described below.
More informationSECTION ORNAMENTAL ALUMINUM FENCING
SECTION 032300 ORNAMENTAL ALUMINUM FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationFIXED SERIES 6200 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4. Glazing Thickness (Maximum): 1
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com FIXED SERIES 6200 AAMA/WDMA/CSA 101/I.S.2/A440-08
More informationEXTERIOR LIGHTWEIGHT STONE CLADDING SYSTEM
63 TECHNICAL SPECIFICATIONS 01 EXTERIOR LIGHTWEIGHT STONE CLADDING SYSTEM PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Honeycomb reinforced exterior stone cladding system. 2. Metal framing support
More informationGrimes Elementary School Renovation September 7, 2010 Houston Independent School District SECTION 102800 - TOILET, BATH, AND LAUNDRY ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general
More informationNorth Hanover Township School District North Hanover Township, New Jersey
SECTION 084413 - GLAZED ALUMINUM CURTAIN WALLS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSECTION STEEL WINDOWS UL Labeled Fire-Rated Fixed Lite (950) Use Tools / Options / View / Hidden Text to view hidden notes and edit.
SECTION 08510 STEEL WINDOWS UL Labeled Fire-Rated Fixed Lite (950) Use Tools / Options / View / Hidden Text to view hidden notes and edit. PART 1 GENERAL 1.1 SECTION INCLUDES A. Fire Rated Steel Windows
More informationDIVISION VIII - DOORS AND WINDOWS
DIVISION VIII - DOORS AND WINDOWS SECTION 08121 INTERIOR ALUMINUM DOORS, DOOR FRAMES, AND OFFICE FRONT FRAMING (SOLUTIONS II SYSTEM) PART 1 - GENERAL 1.01 SUMMARY A. Related Documents: Provisions established
More informationSECTION A. AAMA/NWWDA Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors.
SECTION 08520 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 07200 - Joint Sealers. 2. 08800 - Glass and Glazing. 1.02 REFERENCES A. AAMA/NWWDA 101-97 Voluntary Specifications for
More informationPW251 21/2 x7 GUIDE SPECIFICATION. Curtain Wall
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08900 ALUMINUM CURTAIN WALL This suggested guide specification has
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 08 - OPENINGS. A. This Section includes fixed and operable aluminum-framed windows.
SECTION 085113 - ALUMINUM WINDOWS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes fixed and operable aluminum-framed windows. 1.2 PERFORMANCE REQUIREMENTS A. General: Provide aluminum windows capable
More informationAluminum Storefront Systems SERIES 200, 300 and 500 DOORS GUIDE SPECIFICATIONS
Aluminum Storefront Systems SERIES 200, 300 and 500 DOORS GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONTS This suggested guide specification has been developed using the current edition
More informationSECTION (10705) EXTERIOR SUN CONTROL DEVICES
10 71 13 SECTION (10705) EXTERIOR SUN CONTROL DEVICES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION STEEL WINDOWS UL Labeled Fire-Rated Fixed Lite (950) Use Tools / Options / View / Hidden Text to view hidden notes and edit.
SECTION 08510 STEEL WINDOWS UL Labeled Fire-Rated Fixed Lite (950) Use Tools / Options / View / Hidden Text to view hidden notes and edit. PART 1 GENERAL 1.1 SECTION INCLUDES A. Fire Rated Steel Windows
More informationSECTION ORNAMENTAL WELDED STEEL FENCING
SECTION 032300 ORNAMENTAL WELDED STEEL FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSPECIFICATIONS: Architectural Aluminum Railings
PART ONE: GENERAL 1.1 SUMMARY SPECIFICATIONS: Architectural Aluminum Railings A. Work in this section includes custom and standard Interior and Exterior aluminum railings and guardrails. 1.2 PERFORMANCE
More informationSECTION METAL EQUIPMENT LOCKERS
SECTION 10 51 13 - METAL EQUIPMENT LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified
More information603 Summit Avenue, Suite 102 Greensboro, N.C Voice/FAX (336)
Ricky L. Loman, AIA Architect 603 Summit Avenue, Suite 102 Greensboro, N.C. 27405-7700 Voice/FAX (336) 273-7999 ADDENDUM: Number 1 ISSUED: March 14, 2017 SUBJECT: New Agriculture & Equipment Storage Barn
More informationSECTION ORNAMENTAL ALUMINUM RAILING
SECTION 05730 ORNAMENTAL ALUMINUM RAILING PART 1 GENERAL 1.1 SECTION INCLUDES A. Decorative Wire Rope Railing 1.2 RELATED SECTIONS A. Section 03300 Cast-In-Place Concrete: Placement of sleeves cast in
More informationPROJECT IN SERIES 1300 NARROW SIGHT LINE AAMA/WDMA/CSA 101/I.S.2/A Structural Performance:
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT IN SERIES 1300 NARROW SIGHT
More informationSECTION ARCHITECTURAL GLASS HANDRAIL AND RAILINGS
SECTION 05720 ARCHITECTURAL GLASS HANDRAIL AND RAILINGS PART 1 GENERAL 1.01 WORK INCLUDED A. Furnish and install [aluminum] railings and components. 1.02 REFERENCE A. American Architectural Manufacturers
More informationAMBICO Limited Section and DETENTION STEEL DOOR AND FRAME ASSEMBLIES Page 1
Page 1 This section includes AMBICO Detention Steel Door and Frame assemblies that can be fire rated or non-rated. This section relies on both the Canadian Steel Door Manufacturers Association (CSDMA.org)
More informationSTEEL WINDOWS & DOORS SECTION 08510
SWI Steel Window Specifications STEEL WINDOWS & DOORS SECTION 08510 Steel Window Institute, Inc. 1300 Sumner Ave. Cleveland, OH 44115-2851 Phone: 216-241-7333 Fax: 216-241-0105 E-Mail: swi@steelwindows.com
More informationSECTION ALL ULTREX DOUBLE HUNG WINDOW
SECTION 08 54 13 ALL ULTREX DOUBLE HUNG WINDOW PART 1 GENERAL 1.1 SECTION INCLUDES A. All Ultrex double hung window complete with hardware, glazing, weather strip, insect screen and half screen, grillesbetween-the
More informationSECTION (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 41 13 (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Interior and Exterior Aluminum Storefront Framing, Doors, Door Frames, Lights, and
More informationVELUX America Inc. SPECIFICATION FOR MODEL QPF SELF-FLASHED FIXED SKYLIGHT SECTION UNIT SKYLIGHTS
SECTION 08620 UNIT SKYLIGHTS PART 1 GENERAL 1.01 SECTION INCLUDES A. Performance and product component information for VELUX QPF selfflashed fixed skylight. B. Unit skylight mounted directly to roof decking.
More informationCorium Brick Rainscreen System Specifications
CORIUM BRICK RAINSCREEN SYSTEM PART 1 - GENERAL 1.1 SUMMARY A. Work Included: The Work of this Section shall include but not be limited to the following: 1. Corium brick plates 2. Galvanized and coated
More informationA. This Section includes automatic entrance door systems operating as follows: 1. Swinging operation.
SECTION 08462 - SWINGING AUTOMATIC ENTRANCE DOORS PART 1 - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General, Supplementary, and Special Conditions and Division
More informationPROJECT OUT SERIES 6300 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT OUT SERIES 6300 AAMA/WDMA/CSA
More informationDesign and Construction Standards SECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 GENERAL 1.1 RELATED DOCUMENTS: A. Documents affecting work of this section include but are not necessarily limited to, General Conditions, special provisions and sections
More informationSECTION PRE-ENGINEERED EXTRUDED ALUMINUM DECKING WALKWAY COVERS SPECIFICATION
Awning Works Inc Aluminum Decking Walkway Cover Specification CSI- Division 10 SECTION 10530 PRE-ENGINEERED EXTRUDED ALUMINUM DECKING WALKWAY COVERS SPECIFICATION PART 1 GENERAL 1.01 DESCRIPTION OF WORK
More informationSECTION EXTERIOR SUN SHADES
SECTION 10 71 13 EXTERIOR SUN SHADES USE THIS SECTION WHEN SPECIFYING C.R. LAURENCE 7700 SERIES ALUMINUM SUN SHADE SYSTEMS. THE CRL 7700 SERIES SUN SHADE SYSTEM IS A FIXED BAR GRILLE STYLE WITH A TAPERED
More informationCentral Dartmouth Section Exterior Envelope Renovations METAL-CLAD WOOD DOORS Page 1 of 5 Dartmouth, NS
Exterior Envelope Renovations METAL-CLAD WOOD DOORS Page 1 of 5 Part 1 General 1. RELATED SECTIONS 1. Section 07 92 10 Joint Sealing 2. Section 08 71 00 Door Hardware 2. REFERENCES 1. American Society
More information