.1 Underwriters' Laboratories of Canada (ULC)..1 CAN/ULC-S102-M88(R2000), Surface Burning Characteristics of Building Materials and Assemblies.

Size: px
Start display at page:

Download ".1 Underwriters' Laboratories of Canada (ULC)..1 CAN/ULC-S102-M88(R2000), Surface Burning Characteristics of Building Materials and Assemblies."

Transcription

1 Place D Orléans Transitway Section Place D Orléans Dr, Ottawa, ON. SLIDING DISPLAY BACKDROPS City of Ottawa Project No. CR Page 1 of 2 1 GENERAL 1.01 REFERENCES.1 Underwriters' Laboratories of Canada (ULC)..1 CAN/ULC-S102-M88(R2000), Surface Burning Characteristics of Building Materials and Assemblies SUBMITTALS.1 Provide submittals in accordance with Section Submittal Procedures..2 Product Data:.1 Submit manufacturer's printed product literature, specifications and data sheets CLOSEOUT SUBMITTALS.1 Provide operation and maintenance data in accordance with Section Closeout Submittals 1.04 WASTE MANAGEMENT AND DISPOSAL.1 Separate and recycle waste materials in accordance with Section Waste Management and Disposal. 2 PRODUCTS 2.01 MATERIALS.1 Projection screen:.1 Electric motor operated, mounted inside screen roller on rubber isolation insulators. Motor rated to V AC, with overload protection, electric brake and quiet motor optional feature. Motor and screen housing in continuous pre-finished metal box cover..2 Seamless projection surface with masking borders on flame retardant, Greenguard certified and mildew resistant matte white polyester fabric..1 Size: nominal 900mm wide X 1500mm height.2 Brackets: prefinished ceiling-mounted, purpose made for screen mounting by screen manufacturer for securement into reinforced concrete substrates. 3 EXECUTION 3.01 MANUFACTURER'S INSTRUCTIONS.1 Compliance: comply with manufacturer's written data, including product technical bulletins, product catalogue installation instructions, product carton installation instructions, and data sheets.

2 Place D Orléans Transitway Section Place D Orléans Dr, Ottawa, ON. SLIDING DISPLAY BACKDROPS City of Ottawa Project No. CR Page 2 of INSTALLATION.1 Install in accordance with manufacturer's instructions..2 Install brackets securely anchored to supporting ceiling substrate and suspend screen housing securely to brackets with purpose made attachments..3 Suspend unit at height to achieve bottom of screen backdrop between mm above finished floor when fully retracted from housing..4 Provide electrical connection to motor. Conceal wiring from motor to ceiling connection point with finished metal housing..5 Ensure final installation to have smooth operating screen with plumb and straight vertical edges and plumb and flat viewing surfaces when screen is lowered CLEANING.1 Clean surfaces after installation using manufacturer's recommended cleaning procedures..2 Upon completion of installation, remove surplus materials, rubbish, tools and equipment barriers. END OF SECTION

3 Place D Orléans Transitway Section Place D Orléans Dr, Ottawa, ON. WASHROOM COMPARTMENTS City of Ottawa Project No. CR Page 1 of 3 1 GENERAL 1.01 REFERENCES.1 American Society for Testing and Materials International, (ASTM)..1 ASTM A (2009), Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip..2 Canadian Standards Association (CSA International)..1 CSA B651-04, Accessible Design for the Built Environment..3 City of Ottawa Accessibility Design Standards, November SUBMITTALS.1 Provide submittals in accordance with Section Submittal Procedures.2 Product Data: Submit manufacturer's printed product literature, specifications and data sheets..3 Shop Drawings: Indicate fabrication details, plans, elevations, hardware, and installation details..4 Samples: Provide duplicate 150mm x 150mm sample of each selected colour CLOSEOUT SUBMITTALS.1 Provide operation and maintenance data in accordance with Section Closeout Submittals 1.01 WASTE MANAGEMENT AND DISPOSAL.1 Separate and recycle waste materials in accordance with Section Waste Management and Disposal. 2 PRODUCTS 2.01 MATERIALS.1 Core: solid phenolic..2 Surfaces: plastic laminate in accordance with Section Plastic Laminate Finishing..3 Stainless steel sheet metal: to ASTM A167, Type 304, with satin finish..4 Attachment: stainless steel tamperproof type screws and bolts.

4 Place D Orléans Transitway Section Place D Orléans Dr, Ottawa, ON. WASHROOM COMPARTMENTS City of Ottawa Project No. CR Page 2 of COMPONENTS.1 Hinges:.1 Heavy duty, ball bearing continuous privacy type..2 Material/finish: stainless steel casting..3 Swing: inward and outward..4 Return movement: angled hinge type, door return to return to pilaster with minimum 50mm, maximum 100mm gap..2 Latch set: surface mounted, combination latch, door-stop, keeper and bumper, stainless steel. Exterior safety turn plate..3 Door stop: continuous stainless steel L-angle privacy type..4 Wall and connecting brackets: stainless steel casting, continuous U-channel privacy type..5 Coat hook: combination hook and rubber door bumper, stainless steel, maximum 50mm projection..6 Door pull: 140mm length, D-type suited for out swinging doors, stainless steel..7 Pilaster shoe: 0.8 mm stainless steel, 75 mm high 2.03 FABRICATION.1 Doors, panels and screens for washrooms: 12 mm thick X nominal 1500mm height, two plastic laminate faces pressure bonded to phenolic core, to sizes indicated..2 Pilasters: 19 mm thick, constructed same as panels and doors, to sizes indicated..3 Provide formed and smooth edges for doors, panels and pilasters FINISHES.1 Clean, degrease and neutralize steel components with phosphate or chromate treatment..2 Finish: doors and pilaster/panels as selected from manufacturer's standard colours, total 2 colours for project. 3 EXECUTION 3.01 MANUFACTURER'S INSTRUCTIONS.1 Compliance: comply with manufacturer's written data, including product technical bulletins, product catalogue installation instructions, product carton installation instructions, and data sheets INSTALLATION.1 Ensure supplementary anchorage, if required, is in place..2 Do work in accordance with CAN/CSA B651.

5 Place D Orléans Transitway Section Place D Orléans Dr, Ottawa, ON. WASHROOM COMPARTMENTS City of Ottawa Project No. CR Page 3 of ERECTION.1 Partition erection..1 Install partitions secure, plumb and square..2 Leave 12 mm space between wall and panel or end pilaster..3 Anchor mounting channel to wall surfaces using screws and shields where necessary..4 Attach panel and pilaster to brackets with self-drilling screws with through type sleeve bolt and nut..5 Provide for adjustment of pilaster variations with screw jack through steel saddles made integral with pilaster. Conceal fixings with stainless steel shoes..6 Provide templates for locating threaded studs through finished ceilings..7 Equip doors with hinges, latch set, pulls and each stall with coat hook mounted on partition wall, mounting heights and locations in accordance with City of Ottawa Accessibility Design Standards. Adjust and align hardware for easy, proper function. Install door bumper..8 Install accessories and grab bars in accordance with City of Ottawa Accessibility Design Standards and as indicated..2 Floor supported and overhead braced partition erection:.1 Attach pilasters to floor with pilaster supports and level, plumb, and tighten installation with levelling device..2 Secure pilaster shoes in position..3 Secure headrail to pilaster face with not less than two fasteners per face..4 Set tops of doors parallel with overhead brace when doors are in closed position.3 Screen erection:.1 Provide urinal stall screens consisting of solid panels and wall brackets..2 Panels to extend 300mm from face of wall, located 450mm above finished floor and be nominal 1060mm height..1 Anchor screen panels to walls with 3 panel brackets 3.04 ADJUSTING.1 Adjust doors and locks for optimum, smooth operating condition..2 Lubricate hardware and other moving parts CLEANING.1 Clean surfaces after installation using manufacturer's recommended cleaning procedures..2 Clean and polish hardware and stainless components. END OF SECTION

6 Place D Orléans Transitway Section Place D Orléans Dr, Ottawa, ON. TOILET AND BATH ACCESSORIES City of Ottawa Project No. CR Page 1 of 3 1 GENERAL 1.01\ REFERENCES.1 American Society for Testing and Materials (ASTM).1 ASTM A (2009), Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip..2 ASTM B (2009), Standard Specification for Electrodeposited Coatings of Copper Plus Nickel Plus Chromium and Nickel Plus Chromium..3 ASTM A653/A653M-09a, Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process..2 Canadian General Standards Board (CGSB).1 CAN/CGSB 1.81-M90, Air Drying and Baking Alkyd Primer for Vehicles and Equipment..2 CAN/CGSB , Gloss Alkyd Enamel, Air Drying and Baking..3 CGSB 31-GP-107Ma, Non-inhibited Phosphoric Acid Base Metal Conditioner and Rust Remover..3 Canadian Standards Association (CSA).1 CAN/CSA G164-M92 (R2003), Hot Dip Galvanizing of Irregularly Shaped Articles SUBMITTALS.1 Provide submittals in accordance with Section Submittal Procedures..2 Shop Drawings:.1 Indicate size and description of components, base material, surface finish inside and out, hardware and locks, attachment devices, description of rough-in-frame, building-in details of anchors for grab bars CLOSEOUT SUBMITTALS.1 Provide maintenance data for toilet and bath accessories for incorporation into manual specified in Section Closeout Submittals WASTE MANAGEMENT AND DISPOSAL.1 Separate and recycle waste materials in accordance with Section Waste Management and Disposal EXTRA MATERIALS.1 Provide special tools required for accessing, assembly/disassembly or removal for toilet and bath accessories in accordance with requirements specified in Section Closeout Submittals.

7 Place D Orléans Transitway Section Place D Orléans Dr, Ottawa, ON. TOILET AND BATH ACCESSORIES City of Ottawa Project No. CR Page 2 of 3 2 PRODUCTS 2.01 MATERIALS.1 Sheet steel: to ASTM A653/A653M with ZF001 designation zinc coating..2 Stainless steel sheet metal: to ASTM A167, Type 304, with satin finish..3 Stainless steel tubing: Type 304, satin finished commercial grade, seamless welded, 1.2 mm wall thickness..4 Fasteners: concealed screws and bolts hot dip galvanized, exposed fasteners to match face of unit. Expansion shields fibre, lead or rubber as recommended by accessory manufacturer for component and its intended use COMPONENTS.1 Toilet tissue dispenser: double roll type, surface mounted, satin stainless steel frame with theft resistant spindle, capacity of 500 double ply roll.2 Soap dispenser: Hands-free, wall mounted battery-operated soap dispenser. Dispensing cycles adjustable with tamper proof magnetic key. Seamless type 304 stainless steel cover. Translucent removable internal tank with soap level viewport. LED light to indicate adjustment and operation. Capacity: 1000 ml..3 Grab bars: 38 mm diameter x 1.6 mm wall tubing of stainless steel, 76 mm diameter wall flanges, concealed screw attachment, flanges welded to tubular bar, provided with steel back plates and all accessories. Knurl bar at area of hand grips. Grab bar material and anchorage to withstand downward pull of 2.2 kn..4 Robe hook: stainless steel with maximum 40 mm projection.5 Mirror: wall mounted unit, stainless steel framed mirror of 6 mm tempered glass, sizes as indicated FABRICATION.1 Weld and grind joints of fabricated components flush and smooth. Use mechanical fasteners only where approved..2 Wherever possible form exposed surfaces from one sheet of stock, free of joints..3 Brake form sheet metal work with 1.5 mm radius bends..4 Form surfaces flat without distortion. Maintain flat surfaces without scratches or dents..5 Back paint components where contact is made with building finishes to prevent electrolysis..6 Hot dip galvanize concealed ferrous metal anchors and fastening devices to CSA G Shop assemble components and package complete with anchors and fittings.

8 Place D Orléans Transitway Section Place D Orléans Dr, Ottawa, ON. TOILET AND BATH ACCESSORIES City of Ottawa Project No. CR Page 3 of 3.8 Deliver inserts and rough-in frames to job site at appropriate time for building-in. Provide templates, details and instructions for building in anchors and inserts..9 Provide steel anchor plates and components for installation on studding and building framing FINISHES.1 Chrome and nickel plating: to ASTM B456, satin polished finish..2 Manufacturer's or brand names on face of units not acceptable. 3 EXECUTION 3.01 INSTALLATION.1 Install and secure accessories rigidly in place as follows:.1 Stud walls: install steel back-plate to stud prior to plaster or drywall finish. Provide plate with threaded studs or plugs..2 Hollow masonry units or existing plaster/drywall: use toggle bolts drilled into cell/wall cavity..3 Solid masonry, marble, stone or concrete: use bolt with lead expansion sleeve set into drilled hole..2 Install grab bars on built-in anchors provided by bar manufacturer..3 Use tamper proof screws/bolts for fasteners..4 Fill units with necessary supplies shortly before final acceptance of building..5 Install mirrors by concealed mounting in accordance with manufacturer`s printed instructions SCHEDULE.1 Locate accessories where indicated and as follows. Exact locations determined by Consultant..2 Toilet tissue dispenser: one adjacent to each toilet..3 Grab bar: Install as indicated..4 Robe hook: one for each toilet mounted 1200 mm maximum from floor..5 Soap dispenser: one at each lavatory.6 Mirror: one at each lavatory END OF SECTION

Project No: Pakenham Branch Library, Pakenham, Ontario Section

Project No: Pakenham Branch Library, Pakenham, Ontario Section DECEMBER, 2016 Page 1 of 5 1 GENERAL 1.01 RELATED SECTIONS.1 Section 01 33 00 - Submittal Procedures..2 Section 01 78 00 - Closeout Submittals. 1.02 REFERENCES.1 American Society for Testing and Materials

More information

.2 Section Waste Management and Disposal. 1.2 REFERENCES.1 Codes and standards referenced in this section refers to the latest edition thereof.

.2 Section Waste Management and Disposal. 1.2 REFERENCES.1 Codes and standards referenced in this section refers to the latest edition thereof. Issued 2005/06/01 Section 10800 Toilet, Bath and Laundry Accessories Page 1 of 6 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01330 Submittal Procedures.2 Section 01355 Waste Management and Disposal.3

More information

DTW Works Master Specification Version 2006 Issued 2006/08/01 Section Toilet, Bath and Laundry Accessories Page 1 of 6

DTW Works Master Specification Version 2006 Issued 2006/08/01 Section Toilet, Bath and Laundry Accessories Page 1 of 6 Issued 2006/08/01 Section 10800 Toilet, Bath and Laundry Accessories Page 1 of 6 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01330 Submittal Procedures.2 Section 01355 Waste Management and Disposal.3

More information

Hamilton International Air Cargo Logistics Facility Section November 2014 Page 1 of 4

Hamilton International Air Cargo Logistics Facility Section November 2014 Page 1 of 4 Hamilton International Air Cargo Logistics Facility Section 10 21 14 METAL TOILET COMPARTMENTS Page 1 of 4 Part 1 General 1.1 SECTION INCLUDES.1 Metal toilet compartments, floor mounted. 1.2 RELATED SECTIONS.1

More information

SECTION PLASTIC TOILET COMPARTMENTS

SECTION PLASTIC TOILET COMPARTMENTS PART1 GENERAL 1.01 SECTION INCLUDES A. Phenolic toilet compartments. B. Urinal and vestibule screens. 1.02 REFERENCE STANDARDS SECTION 10 2113.19 PLASTIC TOILET COMPARTMENTS A. ASTM A666- Standard Specification

More information

H D P SOLID PHENOLIC FLOOR BRACED COMPARTMENTS SECTION FB TOILET PARTITIONS

H D P SOLID PHENOLIC FLOOR BRACED COMPARTMENTS SECTION FB TOILET PARTITIONS 3501 East La Palma Avenue - Anaheim, California 92806 PART 1 GENERAL Ph: 714-666-0108 and 714-666-0109 Fax: 714-666-0110 www.weisrobart.com H D P SOLID PHENOLIC FLOOR BRACED COMPARTMENTS 1.1 RELATED DOCUMENTS:

More information

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017 SECTION 10 2113.19 - PLASTIC TOILET COMPARTMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

HDPE SOLID POLYMER-PLASTIC FLOOR BRACED COMPARTMENTS SECTION FB WEIS/POLY TOILET PARTITIONS

HDPE SOLID POLYMER-PLASTIC FLOOR BRACED COMPARTMENTS SECTION FB WEIS/POLY TOILET PARTITIONS 3501 East La Palma Avenue - Anaheim, California 92806 Ph: 714-666-0108 and 714-666-0109 Fax: 714-666-0110 www.weisrobart.com PART 1 GENERAL HDPE SOLID POLYMER-PLASTIC FLOOR BRACED COMPARTMENTS SECTION

More information

H D P SOLID PHENOLIC CEILING HUNG COMPARTMENTS SECTION CH TOILET PARTITIONS

H D P SOLID PHENOLIC CEILING HUNG COMPARTMENTS SECTION CH TOILET PARTITIONS 3501 East La Palma Avenue - Anaheim, California 92806 Ph: 714-666-0108 and 714-666-0109 Fax: 714-666-0110 www.weisrobart.com PART 1 GENERAL 1.1 RELATED DOCUMENTS: H D P SOLID PHENOLIC CEILING HUNG COMPARTMENTS

More information

SECTION TOILET PARTITIONS. A. Section Structural Steel: Supports for ceiling hung compartments.

SECTION TOILET PARTITIONS. A. Section Structural Steel: Supports for ceiling hung compartments. SECTION 10155 TOILET PARTITIONS PART 1 GENERAL 1.1 SECTION INCLUDES A. Stainless steel toilet compartments. 1.2 RELATED SECTIONS A. Section 05120 - Structural Steel: Supports for ceiling hung compartments.

More information

AD 0 O~ Partitions, Inc East La Palma Avenue - Anaheim, California Ph: and Fax:

AD 0 O~ Partitions, Inc East La Palma Avenue - Anaheim, California Ph: and Fax: AD 0 O~ Partitions, Inc. 3501 East La Palma Avenue - Anaheim, California 92806 Ph: 714-666-0108 and 714-666-0109 Fax:714-666-0110 www.weisrobart.com HOPE SOLID POLYMER-PLASTIC COMPARTMENTS PART 1 - GENERAL

More information

HDPE SOLID POLYMER-PLASTIC FLOOR TO CEILING COMPARTMENTS SECTION FC WEIS/POLY TOILET PARTITIONS

HDPE SOLID POLYMER-PLASTIC FLOOR TO CEILING COMPARTMENTS SECTION FC WEIS/POLY TOILET PARTITIONS 3501 East La Palma Avenue - Anaheim, California 92806 Ph: 714-666-0108 and 714-666-0109 Fax: 714-666-0110 www.weisrobart.com HDPE SOLID POLYMER-PLASTIC FLOOR TO CEILING COMPARTMENTS PART 1 GENERAL SECTION

More information

SECTION TOILET COMPARTMENTS SPEC WRITER NOTES:

SECTION TOILET COMPARTMENTS SPEC WRITER NOTES: PART 1 - GENERAL 1.1 DESCRIPTION SECTION 10 21 13 TOILET COMPARTMENTS SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable in

More information

e. Cutouts and Holes for Toilet Accessories: Made to template and edge-reinforced.

e. Cutouts and Holes for Toilet Accessories: Made to template and edge-reinforced. TOILET COMPARTMENTS GENERAL INFORMATION 1.1 Unless otherwise directed by CU Facilities toilet compartments shall be floor-supported, and urinal screens shall be wall hung, with anchoring devices and accessories

More information

SECTION TRESPA ATHLON SOLID COMPOSITE PHENOLIC TOILET PARTITIONS. A. Solid composite phenolic toilet compartments and urinal screens.

SECTION TRESPA ATHLON SOLID COMPOSITE PHENOLIC TOILET PARTITIONS. A. Solid composite phenolic toilet compartments and urinal screens. SECTION 102113 TRESPA ATHLON SOLID COMPOSITE PHENOLIC TOILET PARTITIONS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Solid composite phenolic toilet compartments and urinal screens. 1.02 RELATED SECTIONS

More information

Missouri S&T Bullman Showers Date: February 13, 2017 Project No SECTION PLASTIC SHOWER AND DRESSING COMPARTMENTS

Missouri S&T Bullman Showers Date: February 13, 2017 Project No SECTION PLASTIC SHOWER AND DRESSING COMPARTMENTS SECTION 102116.19 - PLASTIC SHOWER AND DRESSING COMPARTMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and

More information

Construction Standards PAGE

Construction Standards PAGE Construction Standards PAGE 102810-1 SECTION 102810 - PART 1 - GENERAL 1.1 M.S.U. ISSUES A. Mirrors will normally be provided at all lavatory locations. Provide full-length mirror on adjacent wall for

More information

PLASTIC LAMINATED COMPARTMENTS SECTION TOILET PARTITIONS

PLASTIC LAMINATED COMPARTMENTS SECTION TOILET PARTITIONS PHONE (734) 467-8711 Phone: 714.666.0108 / 714.666.0109 FAX (734) 467-8710 www.weisrobart.com Fax: 714.666.0110 3501 E. La Palma Ave., Anaheim, CA 92806 3737 S. VENOY RD. P.O. BOX 130 www.weisrobart.com

More information

1.3 SHOP DRAWINGS.1 Make all submittals in accordance with Division 1, General Requirements

1.3 SHOP DRAWINGS.1 Make all submittals in accordance with Division 1, General Requirements Section 10 21 13 Metal Toilet Partitions Page 1 1. GENERAL 1.1 DESIGN CRITERIA.1 Furnish, deliver and install all Toilet Partitions as indicated on the drawings and as required by actual conditions at

More information

PLASTIC LAMINATED FLOOR TO CEILING COMPARTMENTS SECTION FC TOILET PARTITIONS

PLASTIC LAMINATED FLOOR TO CEILING COMPARTMENTS SECTION FC TOILET PARTITIONS Phone: 714.666.0108 PHONE /(734) 714.666.0109 467-8711 FAX Fax: (734) 714.666.0110 467-8710 www.weisrobart.com 3501 E. La Palma Ave., Anaheim, CA 92806 3737 S. VENOY RD. P.O. BOX 130 www.weisrobart.com

More information

10155 Toilet Compartments

10155 Toilet Compartments 10155 Toilet Compartments This document provides design standards only, and is not intended for use, in whole or in part, as a specification. Do not copy this information verbatim in specifications or

More information

SECTION TOILET COMPARTMENTS. A. Section Metal Fabrications: Concealed steel support members.

SECTION TOILET COMPARTMENTS. A. Section Metal Fabrications: Concealed steel support members. SECTION 10155 TOILET COMPARTMENTS PART 1 GENERAL 1.1 SECTION INCLUDES A. Plastic laminate partitions. 1.2 RELATED SECTIONS A. Section 05500 - Metal Fabrications: Concealed steel support members. B. Section

More information

SECTION SOLID PHENOLIC PLASTIC TOILET PARTITIONS

SECTION SOLID PHENOLIC PLASTIC TOILET PARTITIONS PRODUCT SPECIFICATION SERIES 1080/1180 PART 1 - GENERAL 1.01 Work Included SECTION 10170 SOLID PHENOLIC PLASTIC TOILET PARTITIONS A. Toilet Compartments B. Urinal Screens C. Shower Dividers D. Dressing

More information

SECTION TOILET COMPARTMENTS

SECTION TOILET COMPARTMENTS PART 1 - GENERAL 1.1 DESCRIPTION SECTION 10 21 13 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable

More information

SECTION SOLID PLASTIC TOILET PARTITIONS. A. Section Includes: Toilet partitions and urinal screens, complete with hardware.

SECTION SOLID PLASTIC TOILET PARTITIONS. A. Section Includes: Toilet partitions and urinal screens, complete with hardware. SECTION 10170 SOLID PLASTIC TOILET PARTITIONS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Toilet partitions and urinal screens, complete with hardware. 1.02 REFERENCES A. American Society for Testing

More information

SECTION TOILET AND BATH ACCESSORIES ADDENDUM NO.4

SECTION TOILET AND BATH ACCESSORIES ADDENDUM NO.4 SECTION 10 28 13 - ADDENDUM NO.4 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SOLID PLASTIC TOILET PARTITIONS. A. Section Includes: Toilet partitions and urinal screens, complete with hardware.

SOLID PLASTIC TOILET PARTITIONS. A. Section Includes: Toilet partitions and urinal screens, complete with hardware. SECTION 10170 SOLID PLASTIC TOILET PARTITIONS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Toilet partitions and urinal screens, complete with hardware. 1.02 REFERENCES A. American Society for Testing

More information

The City of Winnipeg SECTION ST. VITAL LIBRARY RENOVATION PROJECT 6 FERMOR AVE. Page 1 of 5

The City of Winnipeg SECTION ST. VITAL LIBRARY RENOVATION PROJECT 6 FERMOR AVE. Page 1 of 5 The City of Winnipeg SECTION 05 50 00 METAL FABRICATIONS ST. VITAL LIBRARY RENOVATION PROJECT 6 FERMOR AVE. Page 1 of 5 Part 1 General 1.1 REFERENCES.1 American Society for Testing and Materials International,

More information

National Master Specification (NMS) Section Publisher: Spex.ca Page 1. Approved: RELATED REQUIREMENTS.1 [ ].

National Master Specification (NMS) Section Publisher: Spex.ca Page 1. Approved: RELATED REQUIREMENTS.1 [ ]. National Master Specification (NMS) Section 05 50 00 METAL FABRICATIONS Publisher: Spex.ca Page 1 Approved: 2010-06-30 Part 1 General 1.1 RELATED REQUIREMENTS.1 [ ]. 1.2 REFERENCES.1 CSA International.1

More information

PRODUCT SPECIFICATIONS - SERIES 1090

PRODUCT SPECIFICATIONS - SERIES 1090 PRODUCT SPECIFICATIONS - SERIES 1090 SECTION 10170 SOLID COLOR REINFORCED COMPOSITE TOILET PARTITIONS PART 1 GENERAL 1.01 Work Included A. Toilet Compartments B. Urinal Screens C. Shower Dividers D. Dressing

More information

SECTION STEEL DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS

SECTION STEEL DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 08110 - STEEL DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General, Supplementary, and Special Conditions and Division 1 Specification

More information

Central Dartmouth Section Exterior Envelope Renovations METAL-CLAD WOOD DOORS Page 1 of 5 Dartmouth, NS

Central Dartmouth Section Exterior Envelope Renovations METAL-CLAD WOOD DOORS Page 1 of 5 Dartmouth, NS Exterior Envelope Renovations METAL-CLAD WOOD DOORS Page 1 of 5 Part 1 General 1. RELATED SECTIONS 1. Section 07 92 10 Joint Sealing 2. Section 08 71 00 Door Hardware 2. REFERENCES 1. American Society

More information

HOLLOW METAL DOORS AND FRAMES SECTION HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL

HOLLOW METAL DOORS AND FRAMES SECTION HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 13686.00 HOLLOW METAL DOORS AND FRAMES 081113-1 SECTION 081113 - HOLLOW METAL DOORS AND FRAMES 1.1 RELATED DOCUMENTS: PART 1 - GENERAL A. Drawings and general provisions of Contract, including General

More information

SECTION ACCORDION FOLDING PARTITIONS

SECTION ACCORDION FOLDING PARTITIONS PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 22 26.13 ACCORDION FOLDING PARTITIONS SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable

More information

B. LEED Submittals (Projects authorized for LEED certification only)

B. LEED Submittals (Projects authorized for LEED certification only) SECTION 10 21 16 - SHOWER AND DRESSING COMPARTMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

1. Seismic Loads: Reference structural drawings.

1. Seismic Loads: Reference structural drawings. SECTION 102213 ~WIRE MESH PARTITIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general prov1s1ons of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

C. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish.

C. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish. SECTION 083113 - ACCESS DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

A. Access doors and frames are part of an access door and frame allowance.

A. Access doors and frames are part of an access door and frame allowance. SECTION 08 31 13 ACCESS DOORS AND FRAMES PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces.

1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces. SECTION 05500- METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION SOLID COLOR REINFORCED COMPOSITE TOILET PARTITIONS

SECTION SOLID COLOR REINFORCED COMPOSITE TOILET PARTITIONS PRODUCT SPECIFICATIONS - SERIES 1090 SECTION 10170 SOLID COLOR REINFORCED COMPOSITE TOILET PARTITIONS PART 1 GENERAL 1.01 Work Included A. Toilet Compartments B. Urinal Screens C. Shower Dividers D. Dressing

More information

Bradley Mills Stainless Steel Toilet Partitions

Bradley Mills Stainless Steel Toilet Partitions Bradley Mills Stainless Steel Toilet Partitions Bradley Mills Stainless Steel Partitions provide a low maintenance, and durable solution for toilet rooms. Bradley's Permaseal panel edge design locks moisture

More information

DIVISION 10 SPECIALTIES I I. Libbie Young Centre, Lloydminster, AB th Avenue, Regina, SK 23 March David W. Edwards Architect Ltd

DIVISION 10 SPECIALTIES I I. Libbie Young Centre, Lloydminster, AB th Avenue, Regina, SK 23 March David W. Edwards Architect Ltd DVSON 10 SPECALTES 200 1102 8 th Avenue, Regina, SK 23 March 2011 DVSON 10 SPECALTES SECTON 1001 00 MSCELLANEOUS SPECALTES PAGE 1 1. GENERAL 1.1 Related Work.1 Wood Blocking Section 06 10 00 1.2 Shop Drawings.1

More information

SECTION DETENTION WINDOW SCREENS. 1. Detention screens for interior and exterior installations at exterior windows in existing buildings.

SECTION DETENTION WINDOW SCREENS. 1. Detention screens for interior and exterior installations at exterior windows in existing buildings. SECTION 08 56 66 DETENTION WINDOW SCREENS SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: SPEC

More information

A This Section includes stock, manufactured toilet compartments.

A This Section includes stock, manufactured toilet compartments. SECTION 102113 -TOILET COMPARTMENTS PART 1 -GENERAL 1.1 SUMMARY A This Section includes stock, manufactured toilet compartments. B. Types of toilet compartments include: 1. Solid plastic, homogenous color.

More information

SECTION MISCELLANEOUS METALS

SECTION MISCELLANEOUS METALS PART 1 GENERAL 1.1 WORK OF THIS SECTION A. Contractor shall provide all labor, materials, equipment and incidentals as shown, specified and required to furnish and install all miscellaneous metal fabrications

More information

Division 11 - Equipment Section 11401

Division 11 - Equipment Section 11401 PART 1 - GENERAL 1.1 GENERAL A. Division 1 General Requirements applies and becomes a part of this Section of the Specification as fully as if repeated herein. B. Items of equipment which are included

More information

Preassembled steel stairs with concrete-filled treads.

Preassembled steel stairs with concrete-filled treads. SECTION 055113 - PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this

More information

.1 American Institute of Steel Construction (AISC) Specifications for Steel Buildings AISC

.1 American Institute of Steel Construction (AISC) Specifications for Steel Buildings AISC 05 12 00 STRUCTURAL STEEL FRAMING Page 1 of 3 1 General 1.1 SECTION INCLUDES.1 Structural steel framing and support members 1.2 RELATED SECTIONS.1 Section 05 50 00 Metal Fabrications 1.3 REFERENCES.1 American

More information

SECTION ACCESS DOORS AND FRAMES

SECTION ACCESS DOORS AND FRAMES SECTION 08310 ACCESS DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. [Fire rated] [and] [Non-fire rated] wall access panels. 2. [Fire rated] [and] [Non-fire rated] ceiling access

More information

SECTION PREFABRICATED SHOWER COMPARTMENTS

SECTION PREFABRICATED SHOWER COMPARTMENTS SECTION 102118 PREFABRICATED SHOWER COMPARTMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary General Conditions and Division

More information

A. American Society for Testing and Materials (ASTM):

A. American Society for Testing and Materials (ASTM): SECTION 05500 METAL FABRICATIONS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 03420 - Precast, Prestress Concrete Sections. 3. 04420 - Concrete Unit Masonry. 4.

More information

SECTION METAL ATHLETIC LOCKERS

SECTION METAL ATHLETIC LOCKERS SECTION 10 51 13 - METAL ATHLETIC LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified

More information

SECTION METAL STAIRS

SECTION METAL STAIRS SECTION 05 51 00 METAL STAIRS PART 1 GENERAL 1.1 SUMMARY A. Section includes steel stair frame of structural sections, with closed risers; pan to receive concrete fill stair treads and landings; integral

More information

Bradley Bradmar Plastic Toilet Partitions

Bradley Bradmar Plastic Toilet Partitions Bradley Bradmar Plastic Toilet Partitions Bradley Bradmar Plastic Partitions provide an economical, durable, and colorful solution for toilet rooms. Bradley's radiused panel edge design locks moisture

More information

Grimes Elementary School Renovation September 7, 2010 Houston Independent School District SECTION 102800 - TOILET, BATH, AND LAUNDRY ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general

More information

SECTION [ ] COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION [ ] COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 08332 [08 33 13] COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Metal Counter

More information

SECTION NON-STRUCTURAL METAL FRAMING

SECTION NON-STRUCTURAL METAL FRAMING SECTION 09 22 16 PART 1 - GENERAL 1.1 DESCRIPTION A. This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories

More information

PASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017

PASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017 SECTION 10505 - METAL STUDENT LOCKERS PART 1 - GENERAL 1.01 SCOPE OF WORK A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

Bid Opportunity No Section Good Neighbours Senior Centre Winnipeg Manitoba Page 1

Bid Opportunity No Section Good Neighbours Senior Centre Winnipeg Manitoba Page 1 Bid Opportunity No. 832-2007 Section 10 09 00 MISCELLANEOUS SPECIALTIES Winnipeg Manitoba Page 1 Part 1 General 1.1 SECTION INCLUDES.1 Projection screen..2 Wire shelving..3 Fall Arrest Anchors.4 Non-Slip

More information

SECTION CHAIN-LINK FENCES AND GATES 02821/1

SECTION CHAIN-LINK FENCES AND GATES 02821/1 SECTION 02821 - CHAIN-LINK FENCES AND GATES 02821/1 PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Chain-Link Fences: 2. Gates: horizontal slide or swing. 3. Fences installed where

More information

1. Bullet resistant hollow metal door and frame assemblies tested in accordance with UL 7 52 and in compliance with the following:

1. Bullet resistant hollow metal door and frame assemblies tested in accordance with UL 7 52 and in compliance with the following: Various Locations PROJECT#: R1401-01 SECTION 083400 -BULLET RESISTANT DOOR AND FRAMES PART 1-GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary

More information

1. Standard two tier metal lockers and metal base.

1. Standard two tier metal lockers and metal base. SECTION 105113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Privacy Plus Partitions

Privacy Plus Partitions Privacy Plus Partitions WITH DuPont Corian solid surface SECTION 10172 PRIVACY PLUS PARTITIONS WITH DUPONT CORIAN SPECIFIER: THROUGHOUT THIS SPECIFICATION EDIT NOTE IS ISSUED TO IDENTIFY ITEMS WHICH SHOULD

More information

SECTION ORNAMENTAL WELDED STEEL FENCING

SECTION ORNAMENTAL WELDED STEEL FENCING SECTION 032300 ORNAMENTAL WELDED STEEL FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

SECTION ORNAMENTAL ALUMINUM FENCING

SECTION ORNAMENTAL ALUMINUM FENCING SECTION 032300 ORNAMENTAL ALUMINUM FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

.2 Section Metal Fabrications: Steel channel frame to suit metal door and operator.

.2 Section Metal Fabrications: Steel channel frame to suit metal door and operator. Page 1 This section includes AMBICO Acoustic Steel Sliding Door assemblies which includes electric operators as an integral part of the assembly. This section includes proprietary, descriptive and performance

More information

Bradley Mills Plastic Laminate Toilet Partitions

Bradley Mills Plastic Laminate Toilet Partitions Bradley Mills Plastic Laminate Toilet Partitions Bradley Mills Plastic Laminate Partitions provide an economical, durable, and colorful solution for toilet rooms. Bradley's high pressure laminate veneers

More information

B. Shop Drawings: For metal lockers. Include plans, elevations, sections, details, and attachments to other work.

B. Shop Drawings: For metal lockers. Include plans, elevations, sections, details, and attachments to other work. SECTION 10 5113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

AMBICO Limited Section and ACOUSTIC STEEL DOOR AND FRAME ASSEMBLIES Page 1

AMBICO Limited Section and ACOUSTIC STEEL DOOR AND FRAME ASSEMBLIES Page 1 Page 1 This section includes AMBICO Acoustic Steel Doors and Frames as well as perimeter and bottom acoustic seals, and glazing if required all of which can be fire rated or non-rated. The aforementioned

More information

SECTION COILING COUNTER DOORS

SECTION COILING COUNTER DOORS SECTION 08 33 13 COILING COUNTER DOORS SPEC WRITER NOTES: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Use overhead coiling counter shutters as closures

More information

SECTION METAL LOCKERS

SECTION METAL LOCKERS PART 1 GENERAL 1.1 DESCRIPTION SECTION 10 51 13 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other items or paragraphs not applicable

More information

1.2 ACTION AND INFORMATIONAL SUBMITTALS.1 Provide submittals in accordance with Section Submittal Procedures.

1.2 ACTION AND INFORMATIONAL SUBMITTALS.1 Provide submittals in accordance with Section Submittal Procedures. BID OPPORTUNITY NO. 253-2011 PAGE 1 OF 7 PART 1 GENERAL 1.1 REFERENCES.1 American Society of Mechanical Engineers (ASME).1 ASME B31.1, Power Piping, B31.3 Process Piping, B31.9 Building Services Piping..2

More information

SECTION METAL FABRICATIONS

SECTION METAL FABRICATIONS SECTION 05500 METAL FABRICATIONS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 03420 - Precast, Prestress Concrete Sections. 3. 04420 - Concrete Unit Masonry. 4.

More information

SECTION SHOWER AND DRESSING COMPARTMENTS

SECTION SHOWER AND DRESSING COMPARTMENTS SECTION 10 21 16 SHOWER AND DRESSING COMPARTMENTS SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes:

More information

.6 ASTM D696 Coefficient of Linear Thermal Expansion

.6 ASTM D696 Coefficient of Linear Thermal Expansion University of Ottawa SECTION 10100 200 Lees Av. Campus HYGENIC PVC WALL & CEILING September 22, 2008 Recommissioning Phase 2 Page 1 of 5 1 General 1.1 RELATED WORK.1 Gypsum Board: Section 09250..2 Finish

More information

METALS Commissioning of Metals Structural Steel Framing Steel Studs... 2

METALS Commissioning of Metals Structural Steel Framing Steel Studs... 2 ~ 05-1 ~ 05 00 00 Metals 05 00 00 METALS... 2 05 08 00 Commissioning of Metals... 2 05 12 00 Structural Steel Framing... 2 05 12 30 Steel Studs... 2 05 45 00 METAL SUPPORT ASSEMBLIES... 2 05 50 00 METAL

More information

K. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.

K. ASTM F436- Standard Specification for Hardened Steel Washers; 2011. DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:

More information

AMBICO Limited Section and DETENTION STEEL DOOR AND FRAME ASSEMBLIES Page 1

AMBICO Limited Section and DETENTION STEEL DOOR AND FRAME ASSEMBLIES Page 1 Page 1 This section includes AMBICO Detention Steel Door and Frame assemblies that can be fire rated or non-rated. This section relies on both the Canadian Steel Door Manufacturers Association (CSDMA.org)

More information

SECTION LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM

SECTION LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM Page 1 of 6 SECTION 08 32 20 LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS SLIDING DOORS. SECTION INCLUDES OVERHEAD SLIDING TUBE ASSEMBLY, MOUNTING

More information

The fire resistance required for doors in this building is 1 (one) hour resistance in compliance with the below general specifications:

The fire resistance required for doors in this building is 1 (one) hour resistance in compliance with the below general specifications: Query No.1 ; we need more specs. about fire resistant doors Answer to Query No. 1: The fire resistance required for doors in this building is 1 (one) hour resistance in compliance with the below general

More information

DETAILED METAL DOOR SPECIFICATION. UNIVERSITY CONTACT: Mark Golden, Supervisor of Structural Services (302)

DETAILED METAL DOOR SPECIFICATION. UNIVERSITY CONTACT: Mark Golden, Supervisor of Structural Services (302) DETAILED METAL DOOR SPECIFICATION UNIVERSITY CONTACT: Mark Golden, Supervisor of Structural Services (302) 831-8456 PART 1 GENERAL DOORS 1.01 GENERAL PROVISIONS I. The Drawings and General Provisions of

More information

SECTION ALUMINUM HANDRAIL SYSTEMS

SECTION ALUMINUM HANDRAIL SYSTEMS SECTION 05520 ALUMINUM HANDRAIL SYSTEMS PART 1 - GENERAL 1.01 SUMMARY A. Section includes aluminum handrails and railings. B. Related Work: 1. Section 03300 - Cast-in-Place Concrete C. References: 1. American

More information

SECTION NON--STRUCTURAL METAL FRAMING

SECTION NON--STRUCTURAL METAL FRAMING The Collective Voice of America s Steel Framing Industry The Steel Framing Industry Association (SFIA) is dedicated to expanding the market for cold-formed steel in construction through programs and initiatives

More information

MASTERSPEC - SHORT FORM. B. See Division 5 Section "Metal Stairs" for steel tube railings associated with metal stairs.

MASTERSPEC - SHORT FORM. B. See Division 5 Section Metal Stairs for steel tube railings associated with metal stairs. SECTION 05721 - ORNAMENTAL RAILINGS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Glass supported railings. B. See Division 5 Section "Metal Stairs" for steel tube railings associated

More information

SECTION METAL STAIRS

SECTION METAL STAIRS SECTION 05510 METAL STAIRS PART 1 GENERAL 1.01 SECTION INCLUDES A. Stairs with concrete treads. B. Stairs with metal treads. C. Structural steel stair framing and supports. D. Handrails and guards. 1.02

More information

B. Provide fire-rated access doors where indicated or scheduled.

B. Provide fire-rated access doors where indicated or scheduled. SECTION 08305 ACCESS DOORS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

Aluminum Perforated Rolling Door

Aluminum Perforated Rolling Door Model ALUMA-VISION Perforated Curved or Flat Slats Rolling Service Door NOTE: For specifications, architects must choose from a variety of options. The standard choice will be shown first in plain text

More information

SECTION CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS

SECTION CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS Page 1 of 6 SECTION 08 32 20 CRL70 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS [OR WOOD] PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,

More information

AMBICO Limited Section BULLET RESISTANT SLIDING STEEL DOOR ASSEMBLY Page 1

AMBICO Limited Section BULLET RESISTANT SLIDING STEEL DOOR ASSEMBLY Page 1 Page 1 This section includes AMBICO bullet resistant steel sliding steel door assembly which includes electric operators as an integral part of the assembly. This section relies on industry standard for

More information

SECTION METAL ATHLETIC LOCKERS

SECTION METAL ATHLETIC LOCKERS SECTION 10 51 13 - METAL ATHLETIC LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified

More information

SECTION OVERHEAD COILING SHUTTERS

SECTION OVERHEAD COILING SHUTTERS SECTION 08336 OVERHEAD COILING SHUTTERS This guide specification has been prepared by C.H.I. Overhead Doors to assist design professionals in the preparation of a specification section covering steel,

More information

SECTION CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS

SECTION CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS SECTION 08 32 20 CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS Page 1 of 6 USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,

More information

SECTION OVERHEAD COILING FIRE DOORS MODEL 662 OVERHEAD COILING COUNTER FIRE DOORS WITH INTEGRAL FRAME

SECTION OVERHEAD COILING FIRE DOORS MODEL 662 OVERHEAD COILING COUNTER FIRE DOORS WITH INTEGRAL FRAME SECTION 08331 OVERHEAD COILING FIRE DOORS MODEL 662 OVERHEAD COILING COUNTER FIRE DOORS WITH INTEGRAL FRAME Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES

More information

SECTION MEDICATION CABINET. 1.1 SUMMARY A. Section Includes: 1. Medication cabinets with self-contained refrigerator and fixtures.

SECTION MEDICATION CABINET. 1.1 SUMMARY A. Section Includes: 1. Medication cabinets with self-contained refrigerator and fixtures. SECTION 12 35 70.21 MEDICATION CABINET SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Medication

More information

SECTION METAL STAIRS

SECTION METAL STAIRS Tender SECTION 05510 METAL STAIRS PART 1 GENERAL 1.01 SECTION INCLUDES A. This section includes internal and external shop fabricated pre assembled steel stairs with integral handrails and ballustrades

More information

DIVISION 5 METALS BUSHEY FEIGHT MORIN ARCHITECTS INC. 473 NORTH POTOMAC STREET HAGERSTOWN, MARYLAND FAX:

DIVISION 5 METALS BUSHEY FEIGHT MORIN ARCHITECTS INC. 473 NORTH POTOMAC STREET HAGERSTOWN, MARYLAND FAX: DIVISION 5 METALS BUSHEY FEIGHT MORIN ARCHITECTS INC. 473 NORTH POTOMAC STREET HAGERSTOWN, MARYLAND 21740 301-733-5600 FAX: 301-733-5612 SECTION 05400 - COLD FORMED METAL FRAMING PART 1 GENERAL 1.1 SECTION

More information

DIVISION 10 SPECIALTIES SECTION METAL LOCKERS

DIVISION 10 SPECIALTIES SECTION METAL LOCKERS DIVISION 10 SPECIALTIES SECTION 10 51 13 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Product Description. Standard Sizes and Hardware Locations

Product Description. Standard Sizes and Hardware Locations F06 1 Product Description A-Series is Fleming s standard adjustable jamb depth 16 gage paintable galvanneal steel, knocked-down, drywall profile, punch mitered frame, used in drywall or existing masonry

More information

B. Polyethylene samples shall be submitted for Owner approval of color and quality.

B. Polyethylene samples shall be submitted for Owner approval of color and quality. Glass Rail ENGINEERED DASHERBOARD SPECIFICATIONS PART 1 - GENERAL 1.01 PROJECT SCOPE A. Contractor shall furnish and install one complete set of steel framed dasherboards as indicated on the drawings and

More information

Nortrax Section David Manchester Road, Ottawa NON-STRUCTURAL METAL FRAMING 16 May 2014 Page 1

Nortrax Section David Manchester Road, Ottawa NON-STRUCTURAL METAL FRAMING 16 May 2014 Page 1 16 May 2014 Page 1 PART 1 GENERAL 1.1 DESCRIPTION This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories

More information