SOPREMA Building Envelope

Transcription

1 SOPREMA Building Envelope

2 WALLS SOPRASEAL Product Table Product Sheets Typical Details FOUNDATIONS COLPHENE Product Table Product Sheets Typical Details PARKING DECKS Polyurethane Product Table PU 3D Image of PU Products Product Sheets Bitumen Product Table 3D Image of Bitumen Products Product Sheets Typical Details ADDITIONAL EXPERTISE BALCONIES Polyurethane Product Table PU 3D Image of PU Products Product Sheets Polymethyl Methacrylate Product Table PMMA 3D Image of PMMA Products Product Sheets Typical Details PLAZA DECKS Polyurethane Product Table PU 3D Image of PU Products Product Sheets Polymethyl Methacrylate Product Table PMMA 3D Image of PMMA Products Product Sheets Bitumen Product Table 3D Image of Bitumen Product Product Sheet Typical Details FOUNTAINS PONDS Polymethyl Methacrylate Product Table PMMA 3D Image of PMMA Products Product Sheets Typical Details Accessories Complementary Products Equipment and Tools

3 AN INDISPENSABLE REFERENCE TOOL The SOPREMA technical manual for building envelope waterproofing solutions was designed to inform specification writers and to facilitate their work. The classification of the waterproofing solutions is simple and helps you to meet your needs in record time. In this manual, you will find everything you need to know about waterproofing of walls, foundations, parking lots, balconies, plaza decks, fountains or ponds. You will be able to make the right choice, but also to discover new solutions. Available Electronically All technical documentation, including technical data sheets, details, specifications, technical bulletins, and this technical manual are available online at in the Technical References Section. We invite you to consult the website regularly to access our most recent updates.

4 HOW TO FIND THE PRODUCTS YOU NEED? In just a few minutes, you can easily find the best waterproofing product for your needs thanks to this manual. All solutions are presented according to the building section. Then, they are classified into subcategories depending on the type of waterproofing required. Finally, the products are shown according to the application method or technology if they are Alsan products. SOPREMA developed a colour code to facilitate searches that will be used in all our communication tools. Thus, each section of the building was assigned a colour: Walls Foundations Parking Decks Additional Expertise Accessories Table You will find a summary table at the beginning of each section. Each table will present the products covered in each section, their characteristics and benefits. This way, you can quickly see the many SOPREMA solutions available and make informed choices. Individual Sheets After the summary table in the WALLS and FOUNDATIONS sections, each product is presented on an single sheet with the installation steps shown on the other side. In the PARKING DECKS and ADDITIONAL EXPERSTISE sections, the individual product sheets are preceded by 3D images of related systems. Typical Details At the end of each section, except for ACCESSORIES, you will find information about typical details.

5 THE PRODUCT GUIDE All product pages have been designed to introduce essential information in a simple and structured manner. Product description 1 Product benefits Application method Installation steps 8 Product main characteristics table 5 Product picture 7 Complementary products Scan the QR code with your smartphone, (having previously installed an app to read the code), and access up-to-date technical documents! 6 Product 3D image

6 SOPREMA, THE BRAND TO KNOW IN CONSTRUCTION SOPREMA is an international manufacturer specializing in the production of waterproofing, insulation, vegetative solutions and soundproofing products for the building and civil engineering sectors. Founded in 1908 in Strasbourg, France, SOPREMA now operates in more than 90 countries. SOPREMA started its operations in Canada in 1978, opening its first production facility and head office in Drummondville, in The North American branch has shown remarkable growth, and now includes seven production facilities that manufacture a large variety of products for industrial, commercial, institutional and residential construction. SOPREMA in Figures... Internationally One head office in Strasbourg, France More than 5,300 employees worldwide 90 countries served Forty production plants worldwide 7 research centres 18 training centres in 5 countries In Canada 1 North American head office in Drummondville, Qc 11 sales offices in Canada More than 60 technicians and technical representatives in Canada 1 research centre in Canada located in Drummondville, with ten people working full time 8 training centres in Canada

7 COMMITTED TO PROVIDING QUALITY SOPREMA s century-old expertise has developed around the idea that the quality, durability and reliability of materials must match builders ambitions and expectations. Over the year, SOPREMA puts its expertise to work developing a variety of high-end products that meet all the requirements of building components: 1 - Roofs 2 - Walls 3 - Foundations 4 - Parking Decks 5 - Bridges 6 - Additional Expertise For all its products, SOPREMA is committed to maintaining a quality management system that meets and exceeds the most stringent requirements of the industry. The company also puts tremendous effort into standardizing its manufacturing processes, ensuring our clients always get the same consistent quality

8 SERVING THE BUILDING INDUSTRY SOPREMA has earned its place among the leaders of the waterproofing industry thanks to the expertise and availability of its technical team. More than 60 technicians and technical representatives across Canada support construction professionals in their projects, from design to build. In addition to providing outstanding technical support and customer service, SOPREMA is committed to providing ongoing training for construction workers who specialize in the installation of waterproofing products. More than 1,000 people are trained each year in one of our eight training centres in Canada. Each year, hundreds of construction professionals architects, contractors, installers, building owners, consultants choose SOPREMA for the quality of its products and its personalized service. SOPREMA is more than a manufacturer: it is also a partner! INNOVATION EXPERTS Always attentive to the professionals in the construction industry, SOPREMA is renowned as a pioneer for its new product development initiatives that meet the needs of the clients and facilitate their work. The company was the first to develop automated systems for the installation of membranes, and was the first roof waterproofing manufacturer to incorporate green roof concepts into their product line. Innovation at SOPREMA also involves active participation in the development of new industry standards. SOPREMA R&D policy is strongly oriented towards sustainable development. For more than 20 years, SOPREMA has taken countless steps to limit the impact of its products and industrial activities on the environment, with a particular emphasis on renewable resources and developing environmentally friendly products, such as SOPRANATURE and SOPRASTAR.

9 BINDER STAR PRODUCTS LINES SOPRASEAL The SOPRASEAL line includes all SOPREMA membranes that ensure air and vapour permeance for walls. SOPRASEAL air and vapour barriers offer durable service and play a key role in waterproofing the building envelope. COLPHENE The COLPHENE line includes all products used to waterproof foundations, from self-adhesive SBS modified bitumen membranes to high-density polyethylene drainage panels. ALSAN The ALSAN line includes liquid waterproofing system products. For waterproofing details impossible to get done with traditional waterproofing solutions on plaza decks, balconies, or parking decks you will find an ALSAN product. TRAFIKROCK TRAFIKROCK products are used to waterproof parking decks. The line includes a choice of primers and thermofusible membranes. They protect the structural concrete against corrosion mainly caused by water and de-icing salt. SOPREMA BY YOUR SIDE EVERY DAY SOPREMA Online Simple, intuitive and practical, SOPREMA s website provides all the information you need with just a few clicks. Technical documents New products Reference sites Company news And much more! SOPREMA Trains Your Team In Canada, SOPREMA quickly earned a place among the waterproofing industry leaders, thanks to the expertise and accessibility of its technical team. More than 60 technicians and technical representatives across Canada work and support construction professionals in their projects. In addition to providing exceptional technical support, SOPREMA is committed to training contractors who specialize in the installation of waterproofing products.

10 DUO SELVEDGE TECHNOLOGY For safer installation, some membranes are equipped with DUO SELVEDGE, a unique technology developed and patented by SOPREMA. The first few inches of DUO SELVEDGE are sealed with self-adhesive to protect the component located underneath from the torch flame. The rest is then safely heat-welded or sealed with hot air. SUSTAINABLE DEVELOPMENT All material manufacturers have a duty to consider on the impact of their products on nature and human health, throughout their life span, from design through manufacturing and eventual demolition. For SOPREMA, this ethical principle resulted in the creation, among other things, of an international environmental policy. Its main objective is to take into account the impact of SOPREMA s products on the environment and health from their design to their destruction, but also to promote a true environmental culture within the company. SOPREMA s sustainable development efforts are far from a new development. In January 1997, SOPREMA was the first company in its field to obtain the ISO certification. This environmental management standard requires us to implement an environmental policy, and more importantly, to monitor it concerning environmental objectives, environmental impacts and risks, and emergency plans, among other things. EN 16001, the standard for energy management systems, guarantees that SOPREMA complies with the most recent practices in the area of energy management. Furthermore, our Drummondville plant, located at 1675 Haggerty Street, was the first site in Canada and the first in the SOPREMA Group to successfully complete the accreditation process for the EN Standard.

11 BITUMEN SOPREMA s bitumen technology has been proving its durability since It is by far the most reliable technology in the industry. Most of SOPREMA s waterproofing membranes are manufactured with SBS modified bitumen and include polyester, glass mat or composite reinforcement. Our experienced research and development team created and refined these membranes, and their unique superior-quality composition makes them exceptionally durable and strong. Water repellent, strong and durable, bitumen has been the material of choice for waterproofing requirements since Antiquity. Bitumen is a natural, noble material that remains on the cutting edge of technology to this day. SOPREMA s research and development centres have always tried to optimize the mechanical properties of bituminous waterproofing membranes in order to give them unequalled durable resistance. Bitumen is said to be an elastomer when it is modified by synthetic compounds or styrene butadiene-styrene (SBS) polymers. The quality of SBS bitumen is determined by the properties of the added elastomers and the formulations used in the mixture. The benefits of elastomeric bitumen: Excellent elasticity and flexibility Characteristic properties at high and low temperatures Excellent adhesion to the substrate Reliable and solid waterproofing for joints Durability

12 REINFORCEMENTS SOPREMA waterproofing membranes are manufactured with four types of reinforcements. A good system always combines the strengths of each reinforcement type to maximize its properties and effectively resist movement caused by the extreme temperatures of the North American climate. Glass Mat Glass mat reinforcement provides waterproofing systems with high dimensional stability. Polyester Polyester reinforcement has a great elongation capacity and is highly puncture resistant. Composite Composite reinforcement combines the benefits of glass mat and polyester reinforcement. This gives it the best resistance to weather and temperature variation. Tri-Laminated Woven Polyethylene Some SOPREMA self-adhesive membranes include a surface reinforcement. As with the reinforcements described above, this material is flexible and reacts very well to movement. Tri-Layer Laminated Woven Polypropylene Some SOPREMA self-adhesive membranes include a surface reinforcement. As with the reinforcements described above, this material is flexible and vapour permeable.

13 APPROVALS, CERTIFICATIONS AND STANDARDS APPROVALS NABA: National Air Barrier Association (or ABAA : Air Barrier Association of America) Air barrier materials are defined by their air and vapour permeance. The National Air Barrier Association defines an air barrier material as one that has been tested and has an air permeance of less than Pa ( lb/ft²). CCMC: Canadian Construction Materials Centre The Canadian Construction Materials Centre is a part of the National Research Council of Canada (NRC). It offers the construction industry a national evaluation service for innovative and non-standardized materials, products, systems and services in all types of construction. The CCMC also evaluates products that are covered under the scope of recognized standards. The CCMC provides an opinion on whether a construction product or system complies with the requirements of the National Building Code of Canada (NBC), among others, as an acceptable solution. Acceptable solutions are those that comply with the Code s applicable requirements. ASTM International : American Society for Testing and Materials Products tested in accordance with the standards of ASTM International comply with the stringent standards recognized in Canada and the USA. These standards evaluate the performance of products used for building waterproofing. These high standards are unquestionably a guarantee of quality. CGBC: Canada Green Building Council LEED (Leadership in Energy and Environmental Design) is a third-party certification program as well as a comparison standard internationally recognized for the design, construction and operation of high-performance green buildings. Many SOPREMA products are qualified to contribute to obtaining LEED credits. Look for the LEED logo to recognize them. Note that, depending on the site location, most SOPREMA products can help obtain the MR Credit 5: Materials and resources (Regional Materials).

14 CERTIFICATIONS ISO 9001 ISO STANDARDS WALLS ASTM E2178 ASTM E2357 ASTM E96 ASTM E154 ASTM D5147 ASTM D412 ASTM D903 ASTM D1876 ASTM D5602 NFPA 285 FOUNDATIONS ASTM D5147 ASTM D5147 ASTM D412 ASTM E154 ASTM D5602 ASTM D5601 ASTM D1876 ASTM D903 ASTM E96 ASTM D5385 ASTM C836 ASTM D1000 ASTM D751 PARKING DECKS CAN/CSA-S413 SECTION 6B ASTM D412 ASTM D2240 ADDITIONAL EXPERSTISE ASTM D412 ASTM D2240

15

16 BUILDING SCIENCE To each project a solution: it is sometimes difficult to navigate through all the products on the market. SOPREMA will thus attempt to summarize in a few words the main principles of building science in relation to the waterproofing of walls, foundations, parking decks, balconies, plaza decks, fountains and ponds. WALLS Components which separate the inside of a building from the outside of it are included in what is called the building envelope. The functions of this barrier are the following: Watertightness Air and vapour tightness Control of heat gains and losses To ensure the smooth operation of the envelope, it is essential to get good continuity between components. Air Leaks Air leaks are a common problem concerning the building envelope. These air leaks are essentially the result of uncontrolled air movement through the building envelope. Air leaks can cause many problems : Condensation Moisture Mould growth Lower air quality inside the building When talking about condensation, it is important to know that warm air can hold more water vapour than cold air. When warm air cools, the percentage of relative humidity increases and can reach a saturation level called the dew point. Then, if the air cools even more, the water vapour surplus which cannot be contained in the air turns into water droplets, thus forming condensation. Causes Air leaks going through the building envelope are caused by air pressure coming from one or more sources, such as wind pressure, the stack effect, or pressure created by heating, cooling and ventilating mechanical units.

17 Using an air barrier to avoid these problems The use of an air barrier becomes necessary to control air leaks. Air barriers are generally divided into two categories: permeable and non-permeable. Non-permeable air barrier Resistant to: air leaks water infiltration diffusion of water vapour Permeable air barrier Good protection against air leaks and water infiltration in the building envelope Must always be set on the warm side of the insulation Allows the diffusion of water vapour Are considered air/vapour barriers Are not considered vapour barriers + 20 C + 20 C Air/vapour barrier Dew point - 20 C Vapour retarder Air barrier (permeable) Dew point - 20 C Two Different Types of Walls Choosing the right type of wall is very important when designing a building. In order to make the most informed choice, it is important to understand what the walls will have to go through during the building s service life. Let s compare the different types of walls that we can find in a cold climate market. Wall with a Continuity of Insulation The first type of wall that we can find is the one with a continuity of the insulation. In this case, the whole structure of the building is kept on the warm side, which greatly reduces thermal bridges. This wall is the most energy efficient and comfortable. The installation of an air/vapour barrier is recommended when constructing these walls. SOPREMA Solutions The products that can be used for these types of walls are: SOPRASEAL STICK 1100 T, SOPRASEAL 60 and 60 FF, SOPRASEAL 180 HD and 180 FF, SOPRASEAL STICK 130 and 130-S, SOPRASEAL XPRESS G, SOPRASEAL LM 200 S and SOPRASEAL LM 200 T. Hybrid Wall The second type of wall that we can find is the hybrid, where insulation is in wall cavities and on the cold side of the permeable air barrier. Insulating materials are added in the cavity between studs, thus moving the dew point inwards. In this assembly, the vapour barrier and air barrier functions are separated. A vapour barrier is installed on the warm side of the insulation and the air barrier is positioned outside the structure. SOPREMA Solutions The product that can be used with hybrid walls is SOPRASEAL STICK VP.

18 FOUNDATIONS Waterproofing foundations is an element often overlooked when developing plans and specifications. In addition to providing an effective barrier to moisture, it helps protect buildings against possible water infiltration. There are several systems that can protect any type of foundation. Whether it is a house or a project located in a densely populated urban area, there is a waterproofing system for every building. Below, you will find the various applications in which installation of a waterproofing system is possible. Waterproofing of Conventional Foundations Conventional Waterproofing This type of waterproofing is related to foundations where waterproofing products are directly installed on the foundation walls. We can find them in most residential, commercial, industrial and institutional buildings. Sealing of foundations with waterproofing membranes is always done on the outside of the building to create positive waterproofing, which means that the hydrostatic pressure exerted by the water pushes the waterproofing membrane against the structure. In the type of construction, the foundation wall is accessible for applicator to apply the membrane to the poured foundation wall. SOPREMA Solutions For this application, we offer two types of membranes: sheet membranes and liquid membranes. Here is a list of the products that can be used with conventional walls: COLPHENE 3000, COLPHENE TORCH N STICK and COLPHENE LM 300.

19 WATERPROOFING OF BLIND SIDE WALLS Perfect for Projects in Dense Urban Areas When the project is located in a high-density urban area, we must take into account the generally restricted space during excavation. In this type of construction, we can find blind side walls (BSW), since waterproofing is done on the outside, before pouring the concrete in place. This type of waterproofing is installed when property lines or other site conditions do not permit the excavation of an open trench outside the perimeter of the foundation. This type of excavation is typically done in urban areas or underground parking decks. Concept Our waterproofing system involves installing self-adhesive waterproofing membranes on a retaining wall or the existing wall of a neighboring building before pouring concrete for the new foundation. This system protects the infrastructure against possible water infiltration between the concrete walls of the buildings. While the concrete is setting, the surface of the Colphene BSW membrane grips onto the newly poured concrete, eliminating the risk of lateral water movement between the waterproofing membrane and the foundation wall. SOPREMA Solutions The COLPHENE BSW system includes the following products: COLPHENE BSW V, COLPHENE BSW H, COLPHENE BSW PROTECT R and SOPRADRAIN products.

20 Waterproofing of Insulated Concrete Forms Insulated concrete forms (ICF) are a type of foundation becoming more and more common. The insulated concrete form keeps the concrete in the best curing conditions. It also provides a high insulation value continuously encapsulating the structure. In addition, the concrete must be reinforced with vertical and horizontal steel rods that make foundations more structurally sound. SOPREMA Solutions The product that is specifically designed with this type of foundation is COLPHENE ICF.

21 PARKING DECKS Whether inside or outside, it is important to protect the concrete in parking decks. They must be protected against the harmful infiltration of water and de-icing salt that can be carried by vehicles, in order to avoid the following problems: Reinforcement corrosion Serious deterioration of the concrete slab resulting in the weakening of the structure SOPREMA offers two effective solutions for the protection of concrete in parking decks. Polyurethane-Based Liquid Waterproofing This liquid waterproofing system, consisting of polyurethane-based resins, can be used both on a new parking slab and one that needs to be renovated. It is intended to be left exposed to vehicular traffic, is resistant to tire traction and does not need to be covered. However, this system is not recommended on slabs where snow will be removed with equipment that may damage the membrane. Benefits: Lightweight (does not add excessive weight to the structure) Thin Flexible Abrasion resistant SOPREMA Solution In this case, the system that can be used is the ALSAN TRAFIK HP 500. Bituminous Membrane Sheet Waterproofing Parking decks can also be protected using a bituminous membrane. This membrane is very resistant to puncturing, allowing circulation of paving equipment directly on its surface. The membranes are thermofused using the MINI-MACADEN automated equipment designed for the installation of bituminous membranes. With this equipment, the installation is quick and uniform. The bituminous membrane is then covered with paving asphalt. Benefits: Excellent puncture resistance Flexible Easy to install SOPREMA Solution The TRAFIKROCK membrane is the product used in these conditions.

22 BALCONIES PLAZA DECKS Found on the majority of buildings, plaza decks and balconies are the place to be when the time comes to take a deep breath of fresh air and relax a little. Therefore, it is important to protect this precious space for so many building occupants. Different systems can be used when performing waterproofing works on these surfaces. Liquid Waterproofing The waterproofing of plaza decks and balconies can be done using a liquid membrane. These systems will better protect the concrete and can be exposed to UV rays. In the case of liquid systems, we offer two types of products: polymethyl methacrylate (PMMA) and polyurethane (PU). Product Polymethyl methacrylate (PMMA) Polyurethane (PU) Description A thermoplastic polymer obtained by polyaddition of a monomer called methyl methylacrylate (MMA) Urethane polymer, an organic molecule Benefits Fast installation and drying Flexible Limitless aesthetic possibilities Flexible Fast installation and drying Abrasion resistant SOPREMA Solutions ALSAN RS products are the ones to use for balconies or plaza decks requiring an installation on concrete or support panels. This system can also quickly open up access to spaces again, something owners appreciate. This is a high performance, flexible and seamless liquid system. The ALSAN TRAFIK HP 500 system is the waterproofing and protection solution for concrete balconies. This system protects the surfaces exposed to foot traffic and ensures waterproofing.

23 Bituminous Membrane Sheet Waterproofing We may also use bituminous membranes, which allow fast implementation, even in cold weather. This membrane is thermofused directly on the previously primed concrete. The membrane is then covered with a slab or some other protection allowing foot or vehicle traffic on the surface. The sections that will be exposed at upstands must be covered with a granulated bituminous membrane. Benefits: Excellent puncture resistance Flexible Easy to install SOPREMA Solutions COLPHENE FLAM 180 membrane is the product to be used in these conditions. FOUNTAINS PONDS Used in most cases as decorative elements, fountains and ponds add prestige to the building they compliment. Since water is an element that can adversely affect concrete, it is very important to protect the structure from this element. SOPREMA Solutions In such cases, ALSAN RS is the solution.

24 WALLS WALLS

25 SOPRASEAL AIR BARRIER PRODUCTS WALL NON-PERMEABLE PERMEABLE TYPE PANEL LIQUIDS SHEET MEMBRANES PRODUCT SOPRASEAL XPRESS G SOPRASEAL LM 200 S SOPRASEAL LM 200 T SOPRASEAL STICK 1100 T SOPRASEAL STICK 130 SOPRASEAL 60 SOPRASEAL 180 HD S FF 180 HD 180 HD FF SOPRASEAL STICK VP IMAGE AIR BARRIER VAPOUR BARRIER X REINFORCEMENT N/A N/A N/A N/A Glass mat Glass mat Non-woven polyester N/A APPLICATION METHOD Mechanically fastened Spray equipment With a trowel or a brush Self-adhesive Self-adhesive Heat-welded Heat-welded Self-adhesive APPLICATION TEMPERATURE Above -35 C Above 2 C Above 2 C Above -10 C Above -10 C Above -35 C Above -35 C -7 to 40 C DESCRIPTION SOPRASEAL XPRESS G is an air and vapour barrier used on walls. It is factory-laminated with modified bitumen adhesive on an exterior gypsum board with surfaces free from organic fibers (paper free). SOPRASEAL LM 200 S is a water-based single-component liquid product made of synthetic rubbers. It is used as an air and vapour barrier on walls. This product can be used on most building surfaces, such as masonry, concrete, wood and gypsum. SOPRASEAL LM 200T is a water-based single-component liquid product made of synthetic rubbers. It is used as an air and vapour barrier on walls or as a rigid insulation adhesive. It can be used on most building surfaces, such as masonry, concrete, wood and gypsum, as well as insulation boards. SOPRASEAL STICK 1100 T self-adhesive membrane is an air and vapour barrier composed of SBS modified bitumen and a tri-laminated woven polyethylene facer. It can also be used as a through-wall membrane, a masonry flashing, a transition membrane, as well as a waterproofing membrane around openings. SOPRASEAL STICK 100 T is available in different widths. The SOPRASEAL STICK 130 and SOPRASEAL STICK 130-S membranes are used as air and vapour barriers on walls. These self-adhesive membranes are composed of SBS modified bitumen and a strong glass mat reinforcement. The surface of the membrane is either sanded or covered with a thermofusible plastic film. SOPRASEAL 60 and 60 FF membranes are used as air and vapour barriers on walls. These membranes are composed of SBS modified bitumen and a glass mat reinforcement. The surface of the membrane is either sanded or covered with a thermofusible plastic film. SOPRASEAL 180 HD and 180 FF HD membranes are used as air and vapour barriers on walls. These membranes are composed of SBS modified bitumen and a non-woven polyester reinforcement. The surface of the membrane is either sanded or covered with a thermofusible plastic film. SOPRASEAL STICK VP is a self-adhesive vapour permeable and air barrier membrane with a tri-laminated polypropylene facer. It can also be used as a throughwall flashing membrane and transition membrane. SOPRASEAL STICK VP is available in different widths. SELECTION FEATURES Membrane factorylaminated to gypsum board under ideal conditions Fewer installation steps Printed grid lines on each board to facilitate easy alignment of fasteners Self-sealing screws Highly UV-resistant Flexible film with a high percentage of elongation Ideal for rough surfaces (LM 200 S only) Easy application and fast installation Can be used on most building surfaces Excellent adhesion to various substrates Ideal for sprayed polyurethane foam insulation Easy, fast and economical to install Self-sealing membranes ensuring continuous waterproofing Monolithic joints with heatwelded edges Excellent dimensional stability Excellent adhesion to various substrates Sanded surface compatible with sprayed polyurethane foam insulation Excellent dimensional stability Excellent adhesion to various substrates Suitable for cold weather application Heat-welded monolithic joints Sanded surface compatible with sprayed polyurethane foam insulation Excellent puncture and tear resistance Suitable for cold weather application Heat-welded monolithic joints Sanded surface compatible with sprayed polyurethane foam insulation Better adhesive properties than competitive products UV exposure up to 180 days Self-sealing membrane ensuring continuous waterproofing No fasteners required

26 SOPRASEAL XPRESS G SOPRASEAL XPRESS G is an air and vapour barrier used on walls. It is factory-laminated with modified bitumen adhesive on an exterior gypsum board with surfaces free from organic fibers (paper free). BENEFITS Fewer installation steps Ideal for installation below -5 C Air and vapour barrier factory laminated on a gypsum board in ideal conditions Grid printed on each board to facilitate screw alignment Self-sealing screws Surface Underface Air and vapour barrier Bitumen Thickness Dimensions Board weight Tri-laminated woven polyethylene Gypsum Tri-laminated woven polyethylene SBS modified Membrane: 0.15 mm (6 mil) Panel: 12.7 mm (1/2 in) 1.2 x 2.44 m (4 x 8 ft) 31.0 kg (68.0 lb) Boards per skid 30 Gross area 2.93 m 2 (32 ft 2 ) APPLICATION METHOD Mechanically fastened TEMPERATURE Application temperature: Above -35 C (-31 F) Walls Mechanically Fastened Product Code SOPRASEAL XPRESS G COMPLEMENTARY PRODUCTS ELASTOCOL STICK and ELASTOCOL STICK ZERO are used to prepare surfaces before the installation of self-adhesive membranes. SOPRASEAL STICK 1100 T in cut rolls is used to ensure sealing of various openings. For further information, visit the product page on our website. SOPRASEAL

27 Walls Mechanically Fastened SOPRASEAL XPRESS G INSTALLATION INSTRUCTIONS 1 2 Install SOPRASEAL XPRESS G panels horizontally on web members. 3 4 Secure panels using SOPRASEAL XPRESS G SCREWS. Soak all surfaces that will receive the self-adhesive membrane with ELASTOCOL STICK to seal the joints between panels. Cover all panel joints with SOPRASEAL STICK 1100 T membrane in cut rolls of 150 mm (6 in). SOPRASEAL 5 6 Complete the application by passing a smoothing roller on membrane strips to ensure perfect adhesion. Completed application of SOPRASEAL XPRESS G.

28 SOPRASEAL LM 200 S SOPRASEAL LM 200 S is a water-based single-component liquid product made of synthetic rubbers. SOPRASEAL LM 200 S is used as an air and vapour barrier on walls. This product can be used on most building surfaces, such as masonry, concrete, wood and gypsum. BENEFITS Easy application and fast installation Can be used on most building surfaces Flexible film with a high percentage of elongation APPLICATION METHOD Apply by spray on smooth or uneven surfaces. Walls Liquid Colour Film thickness Container Service life / storage Cleaning Purple 2.0 mm (80 mil) wet, 1.0 mm (40 mil) dry 1.9 L Up to 2 years in original sealed containers. KEEP AWAY FROM FROST. Freshly applied product can be cleaned with soapy water. After curing, clean with solvents (mineral spirits, Varsol, and xylene) or by using mechanical methods. TEMPERATURE Application temperature: Above 2 C (35 F) Do not use if there is a risk of rain or frost 24 hours after the application. Product Code Units per skid SOPRASEAL LM 200 S COMPLEMENTARY PRODUCTS SOPRASEAL STICK 1100 T in cut rolls is used to ensure sealing of various openings. SOPRASEAL LM 200 T provides a highly flexible film bridging cracks, which may form in the substrate. For further information, visit the product page on our website. SOPRASEAL

29 SOPRASEAL LM 200 S Walls Liquid INSTALLATION INSTRUCTIONS 1 SOPRASEAL LM 200 S is spray applied. The substrate must be clean, solid and free of debris, grease and any contaminants, which may compromise adhesion. 2 Joints and cracks of less than 6 mm (1 4 in) can be filled with SOPRASEAL LM 200 T without using a reinforcement core. It is important to let the product cure in cracks overnight before continuing application of SOPRASEAL LM 200 S over the entire surface. 3 Cracks greater than 6 mm (1 4 in) wide must be covered with a 100 mm (4 in) strip of SOPRASEAL STICK 1100 T or SOPRAGRIP F self-adhesive membrane. ELASTOCOL STICK primer must be used in areas covered by the self-adhesive membrane. Use a hard roller to apply pressure over the entire surface to ensure perfect adhesion. 4 Install SOPRASEAL STICK 1100 T at window and door openings and at transition with roofing. When SOPRASEAL STICK 1100 T is installed over the SOPRASEAL LM 200 S, it must be fully dry and primed with ELASTOCOL STICK before the installation of the self-adhesive membrane. SOPRASEAL 5 The contractor shall inspect membrane installation meticulously at the end 6 of each day of work and also before installation of insulation. Insulation must be installed as soon as possible following inspection by a professional.

30 SOPRASEAL LM 200 T SOPRASEAL LM 200 T is a water-based single-component liquid product made of synthetic rubbers. SOPRASEAL LM 200 T is used as an air and vapour barrier on walls or as a rigid insulation adhesive. It can be used on most building surfaces, such as masonry, concrete, wood and gypsum, as well as insulation boards. Walls Liquid BENEFITS Easy application and fast installation Can be used on most building surfaces Very flexible film with a high percentage of elongation Film thickness Coverage rate Container 2.3 mm (90 mil) wet, 1.15 mm (45 mil) dry About 2 L/m 2, that is 10 m 2 (100 ft 2 ) per container 19 L Units per skid 36 Service life / storage Cleaning Up to 2 years in original sealed containers. KEEP AWAY FROM FROST. Freshly applied adhesive can be cleaned with soapy water. After curing, clean with solvents (mineral spirits, Varsol, and xylene) or by using mechanical methods. APPLICATION METHOD Apply using a trowel or a brush. TEMPERATURE Application temperature: Above 2 C (35 F) Leave to dry at a temperature of 5 C or more. Curing time depends on the relative humidity, temperature and air movement. Do not use if there is a risk of rain or frost 24 hours after the application. SOPRASEAL LM 200 T is not designed to be continuously exposed to moisture. Product Code Colour SOPRASEAL LM 200 T Grey COMPLEMENTARY PRODUCTS SOPRASEAL STICK 1100 T in cut rolls is used to ensure sealing of various openings. SOPRAGRIP F improves the adhesion of liquid air and vapour barrier membranes. For further information, visit the product page on our website. SOPRASEAL

31 SOPRASEAL LM 200 T Walls Liquid INSTALLATION INSTRUCTIONS 1 Cracks and joints greater than 6 mm (1/4 in) wide must be covered with a 150 mm (6 in) strip of SOPRASEAL STICK 1100 T in cut rolls centred on the joint and cracks. Joints and cracks of less than 6 mm (1/4 in) can be filled with SOPRASEAL 200 T. 2 Let SOPRASEAL 200 T cure in cracks before continuing application over the entire surface. Apply the SOPRASEAL 200 T membrane 3 using a trowel. 4 Form a film thickness of 2,3 mm (90 mil) wet. SOPRASEAL

32 SOPRASEAL STICK 1100 T SOPRASEAL STICK 1100 T self-adhesive membrane is an air and vapour barrier composed of SBS modified bitumen and a tri-laminated woven polyethylene facer. The self-adhesive underface is protected by a silicone release paper. It can also be used as a through-wall membrane, a masonry flashing, a transition membrane, as well as a waterproofing membrane around openings. SOPRASEAL WFM can also be used in conjunction with SOPRASEAL STICK 1100 T as a wall flashing membrane. Available in summer and winter grades. BENEFITS Compatibility with sprayed polyurethane Pre-cut rolls available Constant thickness Reference marks every 15 cm (6 in) Easy-to-use silicone release paper Surface Underface Bitumen Thickness Dimensions Roll weight Tri-laminated woven polyethylene Silicone release paper SBS modified 1.0 mm (40 mil) 22.9 x 0.91 m (75 x 3 ft) 21 kg (46.3 lb) Rolls per skid 36 Gross / net area 20.8 m 2 (225 ft 2 )/19.7 m 2 (212 ft 2 ) APPLICATION METHOD Self-adhesive TEMPERATURE Application temperature: Winter grade: From -10 to 40 C (from 14 to 104 F) Summer grade: From 10 to 50 C (from 50 to 122 F) Service temperature: Winter grade: From -45 to 90 C (from -49 to 194 F) Summer grade: From -45 to 90 C (from -49 to 194 F) TESTS AND APPROVALS Walls Self-Adhesive Product Code Grade Summer grade SOPRASEAL STICK 1100 T Winter grade Pour plus de renseignements, visitez la page du produit. SOPRASEAL COMPLEMENTARY PRODUCTS ELASTOCOL STICK, ELASTOCOL STICK H 2 0 and ELASTOCOL STICK ZERO are used to prepare surfaces before the installation of self-adhesive membranes. SOPRASEAL STICK 1100 T in cut rolls is used to ensure sealing of various openings.

33 SOPRASEAL STICK 1100 T Walls Self-Adhesive INSTALLATION INSTRUCTIONS 1 2 Prime the substrate with ELASTOCOL STICK, ELASTOCOL STICK H 2 0 or ELASTOCOL STICK ZERO. Primer must be completely dry before bonding the membrane to the substrate. Peel off the top portion of the silicone release paper and adhere the membrane to the substrate, making sure the membrane is well aligned. 3 4 Gradually peel off the remaining silicone release paper, making sure the membrane adheres completely to avoid air pockets and wrinkles. Use a roller to apply pressure over the entire surface of the membrane to ensure uniform adhesion to the substrate. SOPRASEAL 5 Use a compatible sealant to seal around details, reverse laps and critical areas.

34 SOPRASEAL STICK 130 AND 130-S The SOPRASEAL STICK 130 and SOPRASEAL STICK 130-S membranes are used as air and vapour barriers on walls. These self-adhesive membranes are composed of SBS modified bitumen and a strong glass mat reinforcement. The top surface of the membrane is either sanded or covered with a thermofusible plastic film. The self-adhesive lower face is protected by a silicone release protection film. BENEFITS Monolithic joints with heat-welded edges Excellent dimensional stability Excellent adhesion to various substrates Sanded surface compatible with sprayed polyurethane foam insulation APPLICATION METHOD Self-adhesive TEMPERATURE Application temperature: From -10 to 40 C (from 14 to 104 F) Walls Self-Adhesive Underface Reinforcement Bitumen Thickness Dimensions Silicone release film Glass mat SBS modified 2.5 mm (98 mil) 10 x 1 m Gross / net area 10 m 2 (108 ft 2 )/9 m 2 (97 ft 2 ) Rolls per skid 30 Product Code SOPRASEAL STICK SOPRASEAL STICK 130-S Roll weight 30.0 kg (66.0 lb) 29.0 kg (64.0 lb) Surface Thermofusible plastic film Sand COMPLEMENTARY PRODUCTS ELASTOCOL STICK, ELASTOCOL STICK H 2 0 and ELASTOCOL STICK ZERO are used to prepare surfaces before the installation of self-adhesive membranes. SOPRASEAL STICK 1100 T in cut rolls is used to ensure sealing of various openings. SOPRAMASTIC is the ideal complement to bituminous waterproofing membranes as joint filler and caulking material. For further information, visit the product page on our website. SOPRASEAL

35 SOPRASEAL STICK 130 AND 130-S Walls Self-Adhesive INSTALLATION INSTRUCTIONS 1 2 Prime the substrate with ELASTOCOL STICK, ELASTOCOL STICK H 2 O or ELASTOCOL STICK ZERO. Peel off the top portion of the silicone release film and adhere the membrane to the substrate, making sure the membrane is well aligned. Gradually peel off the remaining silicone release film, ensuring the membrane adheres completely to avoid air pockets. 3 4 Use a roller to apply pressure over the entire surface of the membrane to ensure uniform adhesion to the substrate. Burn off the plastic film to expose bitumen for end lap termination. SOPRASEAL 5 6 Seal termination of the membrane using a round-nosed trowel. * During cold weather, heat from the torch can be applied to the installed membrane s surface to improve adhesion to substrates and overlaps. Use SOPRAMASTIC to seal around details and critical areas.

36 SOPRASEAL 60 AND 60 FF SOPRASEAL 60 and 60 FF membranes are used as air and vapour barriers on walls. These membranes are composed of SBS modified bitumen and a glass mat reinforcement. The top surface of the membrane is either sanded or covered with a thermofusible plastic film. BENEFITS Can be installed in cold temperature Excellent dimensional stability APPLICATION METHOD Heat-welded TEMPERATURE Application temperature: Above -35 C (-31 F) Walls Heat-Welded Underface Thermofusible plastic film Reinforcement Glass mat Bitumen SBS modified Thickness 2.7 mm (106 mil) Dimensions 10 x 1 m (33 x 3.3 ft) Gross / net area 9.1 m 2 (98 ft 2 )/8.6 m 2 (92 ft 2 ) Rolls per skid 30 Product Code Roll weight Surface SOPRASEAL kg (71.0 lb) Sand SOPRASEAL 60 FF kg (68.0 lb) Thermofusible plastic film COMPLEMENTARY PRODUCTS ELASTOCOL 500 is used to prepare surfaces before the installation of heat-weldable membranes. SOPRASEAL STICK 1100 T in cut rolls is used to ensure sealing of various openings. SOPRAMASTIC is the ideal complement to bituminous waterproofing membranes as joint filler and caulking material. For further information, visit the product page on our website. SOPRASEAL

37 SOPRASEAL 60 AND 60 FF Walls Heat-Welded INSTALLATION INSTRUCTIONS 1 2 Prime the substrate with ELASTOCOL 500. Align and heat-weld the membrane providing complete adhesion to the substrate. 3 4 Seal termination of the membrane using a round-nosed trowel. Use SOPRAMASTIC to seal around details and critical areas. SOPRASEAL

38 SOPRASEAL 180 HD AND 180 HD FF SOPRASEAL 180 HD and 180 FF HD membranes are used as air and vapour barriers on walls. These membranes are composed of SBS modified bitumen and a non-woven polyester reinforcement. The top surface of the membrane is either sanded or covered with a thermofusible plastic film. BENEFITS Can be installed in cold temperature Excellent puncture and tear resistance APPLICATION METHOD Heat-welded TEMPERATURE Application temperature: Above -35 C (-31 F) Walls Heat-Welded Underface Thermofusible plastic film Reinforcement Non-woven polyester Bitumen SBS modified Thickness 3 mm (118 mil) Dimensions 10 x 1 m (33 x 3.28 ft) Gross / net area 10 m 2 (107 ft 2 )/9.5 m 2 (102 ft 2 ) Rolls per skid 30 Product Code Roll weight Surface SOPRASEAL 180 HD kg (77 lb) Sand SOPRASEAL 180 HD FF kg (73 lb) Thermofusible plastic film COMPLEMENTARY PRODUCT ELASTOCOL 500 is used to prepare surfaces before the installation of heat-weldable membranes. SOPRASEAL STICK 1100 T in cut rolls is used to ensure sealing of various openings. SOPRAMASTIC is the ideal complement to bituminous waterproofing membranes as joint filler and caulking material. For further information, visit the product page on our website. SOPRASEAL

39 SOPRASEAL 180 HD AND 180 HD FF Walls Heat-Welded INSTALLATION INSTRUCTIONS 1 2 Prime the substrate with ELASTOCOL 500. Align and heat-weld the membrane providing complete adhesion to the substrate. 3 4 Seal terminaton of the membrane using a round-nosed trowel. Use SOPRAMASTIC to seal around details and critical areas. SOPRASEAL

40 SOPRASEAL STICK VP SOPRASEAL STICK VP is a self-adhesive vapour-permeable air barrier membrane with a tri-laminated polypropylene facer. Its width and self-adhesive underface, protected by a silicone release film, make it very easy to install on walls. It can also be used as a through-wall flashing and transition membrane. BENEFITS Better adhesive properties than competitive products UV exposure up to 180 days Self-sealing membrane ensuring continuous waterproofing No fasteners required Pre-cut rolls available APPLICATION METHOD Self-adhesive TEMPERATURE Application temperatures: From -7 to 40 C (from 19 to 104 F) Service temperatures: From -40 to 85 C (from -40 to 185 F) Self-Adhesive Walls Surface Tri-laminated polypropylene complex Underface Self-adhesive, covered with a silicone release film Thickness 0.6 mm (24 mil) Dimensions 30 x 0.95 m (98 ft 37 in) Roll weight 8.1 kg (16.09 lb) Rolls per skid 25 Gross / net area 28.5 m 2 (306 ft 2 ) / 26.2 m 2 (281 ft 2 ) Product Code SOPRASEAL STICK VP COMPLEMENTARY PRODUCT Using a 12-inch neoprene roller maximizes SOPRASEAL STICK VP membrane adhesion. For further information, visit the product page on our website. SOPRASEAL

41 SOPRASEAL STICK VP Walls Self-Adhesive INSTALLATION INSTRUCTIONS 1 2 Peel off the top portion of the silicone release film and adhere the membrane to the substrate, making sure the membrane is well aligned. Gradually peel off the remaining silicone release film, making sure the membrane adheres completely to avoid air pockets and wrinkles. 3 4 Use a roller to apply pressure over the entire surface of the membrane to ensure uniform adhesion to substrate. Use a compatible sealant to seal around details, reverse laps and critical areas. SOPRASEAL

42 Typical Details

43 SOPRASEAL STICK 1100T, SOPRASEAL STICK 130, SOPRASEAL STICK 60 and SOPRASEAL STICK 180 Copyrght 2014 SOPREMA Title Drawing Number Scale Steel Stud Wall Foundation Junction PAR01 N.T.S.

44 SOPRASEAL 200 S Title Drawing Number Scale Steel Stud Wall Foundation Junction PAR01-1 N.T.S. Copyrght 2014 SOPREMA

45 SOPRASEAL XPRESS G Copyrght 2014 SOPREMA Title Drawing Number Scale Steel Stud Wall Foundation Junction PAR01-2 N.T.S.

46 SOPRASEAL 200 T Title Drawing Number Scale Exterior Wall Steel Studs PAR01-3 N.T.S. Copyrght 2014 SOPREMA

47 WINDOW Copyrght 2014 SOPREMA Title Drawing Number Scale Window PAR09 N.T.S.

48 SOPRASEAL STICK VP Title Drawing Number Scale Steel Stud Wall Floor Junction VPAB01 N.T.S. Copyrght 2014 SOPREMA

49 FOUNDATIONS FOUNDATIONS

50 COLPHENE Waterproofing Products FOUNDATIONS INSULATED CONCRETE FORM BLIND SIDE WATERPROOFING CONVENTIONAL TYPE SHEET MEMBRANE LIQUID PRODUCT COLPHENE ICF COLPHENE BSW V COLPHENE BSW H COLPHENE 3000 COLPHENE TORCH N STICK COLPHENE LM 300 IMAGE REINFORCEMENT N/A Composite Non-woven polyester N/A Non-woven polyester N/A APPLICATION METHOD Self-adhesive Self-adhesive Heat-welded Self-adhesive Heat-welded Spray applied APPLICATION TEMPERATURE Above -10 C Above -10 C Above -35 C Above -10 C Above -35 C Above 5 C DESCRIPTION COLPHENE ICF is a high quality self-adhesive waterproofing membrane composed of SBS modified bitumen and a tri-laminate woven polyethylene facer. The self-adhesive underface is protected by a silicone release paper. The membrane is ideal for application on ICF systems or extruded polystyrene substrates. COLPHENE BSW V pre-applied membrane is designed for blind side waterproofing in vertical applications. COLPHENE BSW V is composed of SBS modified bitumen and a composite reinforcement. The sanded membrane is protected with a silicone release film. It features DUO SELVEDGE technology that allows the welding of longitudinal selvedges with a torch or a hot air gun. COLPHENE BSW H pre-applied membrane is designed to waterproof the area under horizontal concrete slabs. COLPHENE BSW H is composed of SBS modified bitumen and a non-woven polyester reinforcement. The sanded membrane is protected with a thermofusible plastic film. Its unique design, with DUO SELVEDGE technology, allows the welding of longitudinal selvedges with a torch or a hot air gun. COLPHENE 3000 self-adhesive membrane is made of SBS modified bitumen and a tri-laminated woven polyethylene facer. The COLPHENE 3000 membrane is used to ensure the waterproofing of foundation walls and other below-grade vertical walls. COLPHENE TORCH N STICK is a waterproofing membrane composed of a non-woven polyester reinforcement and SBS modified bitumen. Both surfaces are covered with a thermofusible plastic film. This product is designed to be used as a waterproofing membrane on concrete foundation walls and other below-grade applications in a vertical position. COLPHENE LM 300 is a water-based single-component liquid waterproofing membrane made of synthetic rubber. COLPHENE LM 300 combines the features of sealants and elastomeric waterproofing. SELECTION FEATURES Constant thickness Greater flexibility High tensile strength and puncture resistance Excellent adhesion to cast-in-place concrete Increased resistance to hydrostatic pressure Superior puncture and tear resistance Very good dimensional stability Excellent adhesion to cast-in-place concrete Increased resistance to hydrostatic pressure Superior puncture and tear resistance Constant thickness Greater flexibility High tensile strength and puncture resistance Fast application Less heat during installation than other SBS modified bitumen membranes No need for adhesive or mechanical fasteners to install drainage High tensile strength; puncture and tear resistant Fast and easy application Greater flexibility Excellent adhesion

51 COLPHENE ICF COLPHENE ICF is a self-adhesive waterproofing membrane designed for the waterproofing of insulated concrete form (ICF) foundations in expanded or extruded polystyrene. It is composed of SBS modified bitumen and a polyethylene woven complex. The self-adhesive underface is protected by a silicone release paper. The COLPHENE ICF membrane is applied directly to the expanded or extruded polystyrene surface of ICF foundations. BENEFITS High tensile strength and puncture resistance Greater flexibility Consistent thickness Surface Underface Bitumen Thickness Dimensions Tri-laminated woven polyethylene Silicone release paper SBS modified 1.0 mm (40 mil) 22.9 x 0.91 m (75 x 3 ft) Gross/net area 20.8 m 2 (225 ft 2 )/19.1 m 2 (206 ft 2 ) Roll weight 20.0 kg (44.0 lb) APPLICATION METHOD Self-adhesive TEMPERATURE Application temperatures: Winter grade: From -10 to 40 C (from 14 to 104 F). Summer grade : From 10 to 50 C (from 50 to 122 F) Service temperatures: Summer and winter grades: From 45 to 70 C (from -49 to 158 F) Foundations Self-Adhesive Product Code Grade COLPHENE ICF Summer Winter COMPLEMENTARY PRODUCTS ELASTOCOL STICK H 2 O is a polymer emulsion-based primer designed to improve the adhesion of self-adhesive waterproofing membranes on most substrates. SOPRASEAL LM 200 T is used as insulation adhesive to seal air/vapour barrier membranes. SOPRAGRIP F is used as a cover strip over COLPHENE ICF membranes top termination. For further information, visit the product page on our website. COLPHENE

52 COLPHENE ICF Foundations Self-Adhesive INSTALLATION INSTRUCTIONS 1 2 Install the footing membrane first, making sure that the inside corner is completely adhered. Peel back the top part of the silicone release paper, making sure the membrane is well aligned. 3 4 Gradually peel back the remaining silicone release paper, making sure the membrane is completely adhered. The use of a roller is required to apply uniform pressure over the entire membrane surface. COLPHENE 5 Top termination must be sealed with SOPRAGRIP For a mastic/sealant, such as SOPRASEAL LM 200 T. The use of a termination bar mechanically fastened to ICF is recommended at membrane s top termination. Backfill: In areas where pit-run sand is not available, a protective board is recommended to ensure the integrity of the waterproofing membrane.

53 COLPHENE BSW V The COLPHENE BSW V pre-applied membrane is designed for blind side waterproofing in vertical applications. COLPHENE BSW V is composed of SBS modified bitumen and a composite reinforcement. It is one of our solutions for projects located in high-density urban areas. COLPHENE BSW V is provided with DUO SELVEDGE technology. BENEFITS Excellent adhesion to cast-in-place concrete Increased resistance to hydrostatic pressure Superior puncture and tear resistance Very good dimensional stability Surface Underface Reinforcement Bitumen Thickness Dimensions Selvedge width Sand Silicone release film Composite SBS modified 3.0 mm (120 mil) 10 x 1 m (33 x 3.3 ft) 100 mm (4 in) Gross/net area 10 m 2 (108 ft 2 ) /9.0 m 2 (96.9 ft 2 ) Roll weight 35.0 kg (77.0 lb) Rolls per skid 30 APPLICATION METHOD Self-adhesive TEMPERATURE Application temperatures: Above 10 C (14 F). For membrane applications at temperatures from 10 C to 10 C, use COLPHENE BSW V in combination with ELASTOCOL STICK primer. TESTS AND APPROVALS Foundations Self-Adhesive Product Code COLPHENE BSW V COMPLEMENTARY PRODUCTS ALSAN FLASHING is a polyurethane/bitumen liquid waterproofing membrane used in combination with FLASHING REINFORCEMENT for sealing around penetrations. ELASTOCOL STICK, ELASTOCOL STICK ZERO and ELASTOCOL STICK H 2 O are used to prepare surfaces before the installation of self-adhesive membranes. SOPRADRAIN 10-G is a high-density drainage board composed of a polypropylene core on which a geotextile is factory laminated. It is used on vertical applications before the installation of COLPHENE BSW V membrane. For further information, visit the product page on our website. COLPHENE

54 COLPHENE BSW V Foundations Self-Adhesive INSTALLATION INSTRUCTIONS 1 Install the SOPRADRAIN drainage board on the timbering or shotcrete (uneven 2 surfaces). Install the SOPRADRAIN filter towards the support. Mechanically fasten the top of the first strip of the membrane to the substrate. 3 Install COLPHENE BSW V on the SOPRADRAIN and make sure that lateral 4 joints are overlapping at a minimum of 100 mm (4 in). Use a rubber roller to ensure good adhesion to the drainage board. 5 Make sure to properly adhere the first 50% of the DUO SELVEDGE and seal the 6 second half with propane torch or a hot air gun. Cover every inside and outside angles with 300 mm (12 in) COLPHENE BSW H membrane strip. COLPHENE

55 COLPHENE BSW H The COLPHENE BSW H pre-applied membrane is designed to waterproof the area under horizontal concrete slabs. COLPHENE BSW H is composed of SBS modified bitumen and a non-woven polyester reinforcement. Its unique design, included DUO SELVEDGE technology, allows the welding of longitudinal selvedges with a torch as well as a hot air gun. BENEFITS Excellent adhesion to cast-in-place concrete Increased resistance to hydrostatic pressure Superior puncture and tear resistance APPLICATION METHOD Heat-welded TEMPERATURE Application temperatures: Above -35 C (-31 F). Foundations Heat-Welded Surface Sand Underface Thermofusible plastic film Reinforcement Non-woven polyester Bitumen SBS modified Thickness 3.5 mm (140 mil) Dimensions 10 x 1 m (33 x 3.3 ft) Selvedge width 100 mm (4 in) Gross/net area 10 m 2 (108 ft 2 )/9.0 m 2 (96.9 ft 2 ) Roll weight 43.0 kg (94.8 lb) Rolls per skid 25 TESTS AND APPROVALS Product Code COLPHENE BSW H COMPLEMENTARY PRODUCTS ALSAN FLASHING is a polyurethane/bitumen liquid waterproofing membrane used in combination with FLASHING REINFORCEMENT for sealing around penetrations. COLPHENE BSW PROTECT R is a fully reinforced protection sheet specially designed for horizontal blind side waterproofing applications. For further information, visit the product page on our website. COLPHENE

56 Foundations Heat-Welded COLPHENE BSW H INSTALLATION INSTRUCTIONS Install COLPHENE BSW H loose laid on 1 2 the working slab or prepared substrate. Offset the roll-end joints at a minimum of 300 mm (12 in) to avoid extra thickness. 3 Make sure that lateral joints are overlapping at a minimum of 100 mm 4 (4 in), and roll-end joints at minimum of 150 mm (6 in) between each selvedge. Seal all DUO SELVEDGE overlaps with propane torch or hot air welder. 5 Install the protection sheet COLPHENE BSW PROTECT R in longitudinal strip over COLPHENE BSW H by removing the siliconed release film on the underside. A minimum of 25 mm overlap is recommended between each strip to facilitate installation. COLPHENE

57 COLPHENE 3000 COLPHENE 3000 is a self-adhesive waterproofing membrane composed of SBS modified bitumen and a tri-laminated woven polyethylene facer. The self-adhesive underface is protected by a silicone release film. The COLPHENE 3000 membrane is used to ensure the waterproofing of foundation walls and other below grade vertical walls. BENEFITS High tensile strength and puncture resistance Greater flexibility Constant thickness Surface Underface Bitumen Thickness Dimensions Tri-laminated woven polyethylene Silicone release film SBS modified 1.5 mm (60 mil) 18.7 x 1 m (61 x 3.3 ft) Gross/net area 18.7 m 2 (201 ft 2 )/17.3 m 2 (186 ft 2 ) Roll weight 29.0 kg (64.0 lb) APPLICATION METHOD Self-adhesive TEMPERATURE Application temperatures: Winter grade: From -10 to 10 C (from 14 to 50 F). Summer grade: From 10 to 50 C (from 50 to 122 F) TESTS AND APPROVALS Foundations Self-Adhesive Product Code Grade Rolls per skid COLPHENE 3000 With boxes COLPHENE 3000 Without boxes Summer Winter Summer Winter 30 COMPLEMENTARY PRODUCTS ELASTOCOL STICK, ELASTOCOL STICK ZERO and ELASTOCOL STICK H 2 O are used to prepare surfaces before the installation of self-adhesive membranes. SOPRAMASTIC is the ideal complement to bituminous waterproofing membranes as joint filler and caulking material. For further information, visit the product page on our website. COLPHENE

58 COLPHENE 3000 Foundations Self-Adhesive INSTALLATION INSTRUCTIONS 1 2 Prime the substrate with ELASTOCOL STICK, ELASTOCOL STICK ZERO or ELASTOCOL STICK H 2 O. Peel back the top part of the silicone release film. Adhere COLPHENE 3000 to the substrate, making sure the membrane is well aligned. 3 4 Gradually peel back the remaining silicone release film, making sure the membrane is completely adhered. The use of a hand roller is required to remove air pockets. Use SOPRAMASTIC to seal details and critical areas. The use of a protection or drainage board is recommended before backfilling to ensure the integrity of the waterproofing membrane. COLPHENE 5 Here is a completed waterproofing project.

59 COLPHENE TORCH N STICK COLPHENE TORCH N STICK is a waterproofing membrane composed of a non-woven polyester reinforcement and SBS modified bitumen. Both sides of the membrane are coated with a thermofusible plastic film. This product is designed to be used as a waterproofing membrane on concrete foundation walls and other below-grade applications in a vertical position. BENEFITS Fast application Less heat during installation than other SBS modified bitumen membranes No need for adhesive or mechanical fasteners to install drainage, protection or insulation boards High tensile strength; puncture and tear resistant APPLICATION METHOD Heat-welded TEMPERATURE Application temperatures: Above -35 C (-31 F). Foundations Heat-Welded Surface Thermofusible plastic film Underface Thermofusible plastic film Reinforcement Non-woven polyester Bitumen SBS modified Thickness 2.7 mm (106 mil) Dimensions 12 x 1 m (39 x 3.3 ft) Gross area 12 m 2 (129 ft 2 ) Roll weight 34.0 kg (75.0 lb) Product Code COLPHENE TORCH N STICK COMPLEMENTARY PRODUCTS ELASTOCOL 500 and ELASTOCOL 350 are primers used to improve the adhesion of torch-applied waterproofing membranes. For further information, visit the product page on our website. COLPHENE

60 COLPHENE TORCH N STICK Foundations Heat-Welded INSTALLATION INSTRUCTIONS 1 2 Prime the substrate with ELASTOCOL 500. Install COLPHENE TORCH N STICK by heat-welding to the foundation wall, only when the primer is completely dry. 3 4 Proceed with the installation of the membrane on the footing. Use a propane torch and a trowel, to seal the top end and all side laps. COLPHENE 5 6 Use the propane torch to burn off the plastic film and lightly warm the membrane surface to reveal the sticky surface. Adhere the protection, insulation or drainage board directly to the membrane.

61 COLPHENE LM 300 COLPHENE LM 300 is a water-based single-component liquid waterproofing membrane made of synthetic rubbers. COLPHENE LM 300 is easy to apply and after curing, becomes a strong, highly flexible, jointless membrane, which combines the features of sealant and elastomeric waterproofing. BENEFITS Fast and easy application Greater flexibility Excellent adhesion APPLICATION METHOD Apply in a criss-cross pattern at 90 in three successive sprayed coats. Foundations Liquid Film thickness 2 mm (80 mil) wet, 1 mm (40 mil) dry Coverage rate 1.9 L/m 2 Container 19 L (5 US gal) Units per skid 36 Service life/storage Cleaning Up to 2 years in the original sealed containers. Freshly applied product can be cleaned with soapy water. After curing, clean with solvents (mineral spirits, Varsol, and xylene) or by using mechanical methods. TEMPERATURE Application temperatures: Above 5 C (41 F). Do not use if rain or frost is forecast 24 hours after the application. TESTS AND APPROVALS Product Code Colour COLPHENE LM Pink in liquid state, red in solid state COMPLEMENTARY PRODUCTS ELASTOCOL STICK is a primer designed to enhance the adhesion of self-adhesive membranes on surfaces such as concrete and metal. SOPRADRAIN 10-G is a high-density drainage board composed of a polypropylene core on which a geotextile is factory laminated. It is used on vertical applications before the installation of COLPHENE LM 300 membrane. SOPRASEAL LM 200 T is used as insulation adhesive to seal joints and other details. For further information, visit the product page on our website. COLPHENE

62 COLPHENE LM 300 Liquid Foundations INSTALLATION INSTRUCTIONS 1 2 Seal joints and cracks using SOPRASEAL LM 200 T (less than 6 mm). Cover cracks (more than 6 mm) with 150 mm COLPHENE 3000 membrane on a surface prepared with ELASTOCOL STICK. Apply required thickness at 90 degrees in three successive sprayed coats. 3 4 Continue the installation in angles and around obstacles. Check thickness using a wet gauge. COLPHENE 5 6 The product will change color during drying. A minimum drying period of 24 to 48 hours is required before installing the protective board and backfilling.

63 Typical Details

64 COLPHENE 3000 and COLPHENE TORCH N STICK Copyrght 2014 SOPREMA Title Drawing Number Scale Foundation Wall and Footing Below Grade BGW01-2 N.T.S.

65 COLPHENE LM 300 Title Drawing Number Scale Foundation Wall and Footing Below Grade BGW01-3 N.T.S. Copyrght 2014 SOPREMA

66 COLPHENE ICF Copyrght 2014 SOPREMA Title Drawing Number Scale Foundation Wall and Footing Below Grade BGW01-4 N.T.S.

67 COLPHENE BSW V, COLPHENE BSW H and COLPHENE BSW PROTECT R Title Drawing Number Scale Blind Side Waterproofing Slab on Grade BGW02 N.T.S. Copyrght 2014 SOPREMA

68 COLPHENE BSW V, COLPHENE BSW H and COLPHENE BSW PROTECT R Copyrght 2014 SOPREMA Title Drawing Number Scale Blind Side Waterproofing BGW06-1 N.T.S.

69

70 PARKING DECKS PARKING DECKS

71 PU TRAFIK HP Liquid System COATS PRIMER WATERPROOFING WEAR COAT FINISH COAT PRODUCT ALSAN TRAFIK EP 110 ALSAN TRAFIK HP 515 ALSAN TRAFIK HP 520 ALSAN TRAFIK HP 530 ALSAN TRAFIK HP 540 IMAGE APPLICATION METHOD Roller Squeegee and roller Notched squeegee and roller Squeegee and roller Roller APPLICATION TEMPERATURE Above 10 C Above 5 C Above 5 C Above 5 C Above 5 C DESCRIPTION ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fastdrying primer, increasing the subsequent adhesion of the ALSAN TRAFIK HP 500 system. It is also used for junctions where the ALSAN TRAFIK HP 500 system meets SOPREMA bituminous membranes. ALSAN TRAFIK HP 515 is a low-odour, two-component polyurethane resin, VOC free, 100% solids, used as a primer on substrates such as concrete and plywood. ALSAN TRAFIK HP 520 is a single-component polyurethane resin waterproofing membrane. ALSAN TRAFIK HP 530 is a single-component polyurethane resin wear coat that ensures the durability of the TRAFIK HP 500 system. It is installed in one or more layers depending on the traffic density. ALSAN TRAFIK HP 540 is a single-component aliphatic polyurethane transparent resin finish coat. It provides the TRAFIK HP 500 system with greater durability and facilitates its cleaning. ALSAN TRAFIK HP 540 can be tinted if necessary. SELECTION FEATURES Vapour barrier Quick setting to meet tight deadlines Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application

72 Parking Decks PU Light Duty Vehicular Traffic ALSAN TRAFIK HP 540 ALSAN TRAFIK HP 520 ALSAN TRAFIK HP 515 or ALSAN TRAFIK EP 110 Concrete deck ALSAN TRAFIK HP aggregates

73 Parking Decks PU Heavy Duty Vehicular Traffic ALSAN TRAFIK HP 540 ALSAN TRAFIK HP 530 ALSAN TRAFIK HP 520 ALSAN TRAFIK HP aggregates ALSAN TRAFIK HP 515 or ALSAN TRAFIK EP 110 Concrete deck

74 Parking Decks Bitumen Heavy Duty Vehicular Traffic ALSAN FLASHING Asphalt Reinforcement TRAFIKROCK ANTIROCK PRIMER Concrete deck

75 ALSAN TRAFIK EP 110 ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fast-drying primer, increasing the subsequent adhesion of the ALSAN TRAFIK HP 500 system on concrete. It is also used for junctions where the ALSAN TRAFIK HP 500 system meets SOPREMA bituminous membranes. Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Thickness Coverage rate per kit 0.25 mm (10 mil) 2 x 0.25 mm (2 x 10 mil) 13 m 2 (140 ft 2 ) with wet film thickness of 0.25 mm (10 mils) 7 m 2 (70 ft 2 ) with wet film thickness of 0.50 mm (20 mils) Units per skid 75 Storage / service life Containers must be stored away from heat, moisture and sunlight. Storage: up to 18 months in original sealed containers at a temperature between 5 C and 35 C (41 F and 95 F). APPLICATION METHOD Apply with a short nap roller or a brush. Part B has to be blended with the Part A for 2 to 3 minutes until homogeneity is obtained. TEMPERATURE Application temperature: Above 10 C (50 F). The mixture can be used for 15 to 20 minutes at 25 C (77 F). TESTS AND APPROVALS Parking Decks EPOXY Product Code Colour ALSAN TRAFIK EP Amber For further information, visit the product page on our website. TRAFIK HP

76 ALSAN TRAFIK HP 515 Parking Decks PU ALSAN TRAFIK HP 515 is a low-odour two-component polyurethane resin, VOC free, 100% solids, used as a primer on substrates, such as concrete and plywood. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application APPLICATION METHOD Apply with a squeegee or a roller. Part B has to be blended with Part A for 2 to 3 minutes until homogeneity is obtained. Thickness Coverage rate Container 125 μm (5 mil) wet 37 m 2 (400 ft 2 ) per container 7.1 L Units per skid 60 Storage / service life 24 months when properly stored in original sealed containers. TEMPERATURE Application temperature: Above 5 C (41 F). The mixture can be used for 15 to 20 minutes at 25 C (77 F). TESTS AND APPROVALS Product Code Colour ALSAN TRAFIK HP Amber TRAFIK HP For further information, visit the product page on our website.

77 ALSAN TRAFIK HP 520 ALSAN TRAFIK HP 520 is a single-component, ready-to-use, polyurethane waterproofing membrane. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application APPLICATION METHOD Apply with a notched squeegee or a roller. When the primer is set, the waterproofing membrane is applied with a 6 mm notched squeegee at the rate of 0.68 L/m 2 (300 ft 2 /19 L) and must be levelled with a roller. Membrane thickness shall have a wet film thickness of 700 micrometers (28 mil). Parking Decks PU Thickness Coverage rate Container 700 μm (28 mil) wet 28 m 2 (300 ft 2 ) per container 19 L Units per skid 36 Storage / service life 18 months when properly stored in original sealed containers. TEMPERATURE Application temperature: Above 5 C (41 F). Product Code Colour ALSAN TRAFIK HP Grey COMPLEMENTARY PRODUCT ALSAN TRAFIK HP ACCELERATOR is added to ALSAN TRAFIK HP 520 to accelerate the drying time of the liquid waterproofing membrane. For further information, visit the product page on our website. TRAFIK HP

78 ALSAN TRAFIK HP 530 Parking Decks PU ALSAN TRAFIK HP 530 is a single-component, ready-to-use, polyurethane wear layer that ensures the durability of the TRAFIK HP 500 system. It is installed in one or more layers depending on the traffic density. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application Thickness Coverage rate Container 300 μm (13 mil) wet 56 m 2 (600 ft 2 ) per container 19 L Units per skid 36 Storage / service life 18 months when properly stored in original sealed containers. APPLICATION METHOD Apply with a squeegee or a roller. When the waterproofing membrane is set, the wear layer is applied with a squeegee or a roller at the rate of 0.51 L/m 2 (600 ft 2 /19 L) and the aggregate is spread onto the wear layer in order to obtain a non-slip finish. The wear layer must be levelled with a roller and shall have a wet film thickness of 300 micrometers (13 mil) before the application of aggregates. TEMPERATURE Application temperature: Above 5 C (41 F). Product Code Colour ALSAN TRAFIK HP Grey Dark grey TRAFIK HP COMPLEMENTARY PRODUCTS COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements. For further information, visit the product page on our website.

79 ALSAN TRAFIK HP 540 ALSAN TRAFIK HP 540 is a single component aliphatic polyurethane transparent resin finish coat. It provides the TRAFIK HP 500 system with greater durability and facilitates its cleaning. ALSAN TRAFIK HP 540 can be tinted if necessary. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application APPLICATION METHOD Apply with a roller. When the wear layer is set, the finish coat is applied with a roller at the rate of 70 m 2 /19 L (750 ft 2 /19 L) in order to obtain a wet film thickness of 250 micrometers (10 mil). Parking Decks PU Thickness Coverage rate Container 250 μm (10 mil) wet 70 m 2 (750 ft 2 ) per container 19 L Units per skid 36 Storage / service life 18 months when properly stored in original sealed containers. TEMPERATURE Application temperature: Above 5 C (41 F). Product Code Colour ALSAN TRAFIK HP Clear COMPLEMENTARY PRODUCT ALSAN TRAFIK HP COLORANT is a pigment paste added to ALSAN TRAFIK HP 540. For further information, visit the product page on our website. TRAFIK HP

80

81 BITUMEN TRAFIKROCK Waterproofing Products TYPE SHEET MEMBRANE PRODUCT TRAFIKROCK STARTER TRAFIKROCK IMAGE REINFORCEMENT Non-woven polyester Non-woven polyester APPLICATION METHOD Heat-welded Heat-welded APPLICATION TEMPERATURE Above -35 C Above -35 C DESCRIPTION SELECTION FEATURES TRAFIKROCK STARTER waterproofing membrane is composed of a non-woven polyester reinforcement and SBS modified elastomeric bitumen. Its underface is protected by a thermofusible plastic film, and its surface is covered with coloured granules. TRAFIKROCK STARTER membrane is designed to ensure the waterproofness of parking structures. This membrane must be thermofused on a dry, clean surface previously coated with ANTIROCK PRIMER or ANTIROCK EMULSION PRIMER. Excellent tear and puncture resistance Double laps for fast installation High elasticity Superior waterproofness TRAFIKROCK waterproofing membrane is composed of a non-woven polyester reinforcement and SBS modified elastomeric bitumen. Its underface is protected by a thermofusible plastic film, and its surface is covered with coloured granules. TRAFIKROCK membrane is designed to ensure the waterproofness of parking structures. This membrane must be thermofused on a dry, clean surface previously coated with ANTIROCK PRIMER or ANTIROCK EMULSION PRIMER. Excellent tear and puncture resistance Easy to install High elasticity Superior waterproofness

82 TRAFIKROCK STARTER The TRAFIKROCK STARTER waterproofing membrane is composed of a non-woven polyester reinforcement and SBS modified elastomeric bitumen. Its underface is protected by a thermofusible plastic film, and its surface is covered with coloured granules.the TRAFIKROCK STARTER membrane is designed to ensure the waterproofness of parking structures. BENEFITS Excellent tear and puncture resistance Double laps for fast installation High elasticity Superior waterproofness APPLICATION METHOD Heat-welded Welded with MINI MACADEN Parking Decks Heat-Welded Surface Sienna granules Underface Thermofusible plastic film Reinforcement Non-woven polyester Bitumen SBS modified Thickness 4.5 mm (177 mil) Selvedge width 75 mm (3 in) Rolls per skid 25 TEMPERATURE Application temperature: Above 35 C ( 31 F). Product Code Dimensions Roll weight TRAFIKROCK STARTER x 1 m (26 x 3.28 ft) 43 kg (95 lb) x 0.5 m (26 x 1.6 ft) 21,5 kg (47 lb) COMPLEMENTARY PRODUCTS ALSAN FLASHING is a single-component polyurethane waterproofing coating used for upstands and other complex details. ANTIROCK PRIMER and ANTIROCK EMULSION PRIMER enhance the adhesion of waterproofing membranes for parking structures. For further information, visit the product page on our website. TRAFIKROCK HP

83 TRAFIKROCK Parking Decks Heat-Welded The TRAFIKROCK waterproofing membrane is composed of a non-woven polyester reinforcement and SBS modified elastomeric bitumen. Its underface is protected by a thermofusible plastic film, and its surface is covered with coloured granules.the TRAFIKROCK membrane is designed to ensure the waterproofness of parking structures. BENEFITS Excellent tear and puncture resistance Easy to install High elasticity Superior waterproofness APPLICATION METHOD Heat-welded Welded with MACADEN Surface Sienna granules Underface Thermofusible plastic film Reinforcement Non-woven polyester Bitumen SBS modified Thickness 4.5 mm (177 mil) Selvedge width 75 mm (3 in) Rolls per skid 25 TEMPERATURE Application temperature: Above 35 C ( 31 F). TESTS AND APPROVALS 14/5172 Product Code Dimensions Roll weight Gross/net area Rolls per skid TRAFIKROCK x 1 m (26 x 3.28 ft) 200 x 1 m* (656 x 3.28 ft) 45 kg (99 lb) 8 m 2 (86 ft 2 )/7.4 m 2 (80 ft 2 ) 25 1,150 kg (2,535 lb) 200 m 2 (2,153 ft 2 )/ 185 m 2 (1,991 ft 2 ) 1 * On request only. TRAFIKROCK COMPLEMENTARY PRODUCTS ALSAN FLASHING is a single-component polyurethane waterproofing coating used for upstands and other complex details. ANTIROCK PRIMER and ANTIROCK EMULSION PRIMER enhance the adhesion of waterproofing membranes for parking structures. For further information, visit the product page on our website.

84 Typical Details

85 TRAFIK HP 500 Copyrght 2014 SOPREMA Title Drawing Number Scale ALSAN TRAFIK HP 500 System TRAFIK-01 N.T.S.

86 TRAFIKROCK Title Drawing Number Scale Upstand Detail (Parking Deck) TROCK01 N.T.S. Copyrght 2014 SOPREMA

87 ADDITIONAL EXPERTISE ADDITIONAL EXPERTISE

88 BALCONIES

89 PU TRAFIK HP Liquid System COATS PRIMER WEAR COAT FINISH COAT PRODUCT ALSAN TRAFIK EP 110 ALSAN TRAFIK HP 515 ALSAN TRAFIK HP 530 ALSAN TRAFIK HP 540 IMAGE APPLICATION METHOD Roller Squeegee and roller Squeegee and roller Roller APPLICATION TEMPERATURE Above 10 C Above 5 C Above 5 C Above 5 C DESCRIPTION ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fast-drying primer, increasing the subsequent adhesion of the ALSAN TRAFIK HP 500 system. It is also used for junctions where the ALSAN TRAFIK HP 500 system meets SOPREMA bituminous membranes. ALSAN TRAFIK HP 515 is a low-odour, twocomponent polyurethane resin, VOC free, 100% solids, used as a primer on substrates such as concrete and plywood. ALSAN TRAFIK HP 530 is a single-component polyurethane resin wear coat that ensures the durability of the TRAFIK HP 500 system. It is installed in one or more layers depending on the traffic density. ALSAN TRAFIK HP 540 is a single-component aliphatic polyurethane transparent resin finish coat. It provides the TRAFIK HP 500 system with greater durability and facilitates its cleaning. ALSAN TRAFIK HP 540 can be tinted if necessary. SELECTION FEATURES Vapour barrier Quick setting to meet tight deadlines Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application

90 Additional Expertise Balconies PU Balconies ALSAN TRAFIK HP 540 ALSAN TRAFIK HP aggregates ALSAN TRAFIK HP 515 or ALSAN TRAFIK EP 110 Concrete deck Note: To add colour to the system, the Alsan Trafik HP 540 can be used in finish coat

91 ALSAN TRAFIK EP 110 ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fast-drying primer, increasing the subsequent adhesion of the ALSAN TRAFIK HP 500 system on concrete. It is also used for junctions where the ALSAN TRAFIK HP 500 system meets SOPREMA bituminous membranes. Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Thickness Coverage rate per kit 0.25 mm (10 mil) 2 x 0.25 mm (2 x 10 mil) 13 m 2 (140 ft 2 ) with wet film thickness of 0.25 mm (10 mil) 7 m 2 (70 ft 2 ) with wet film thickness of 0.50 mm (20 mil) Units per skid 75 Storage / service life Containers must be stored away from heat, moisture and sunlight. Storage: up to 18 months in original sealed containers at a temperature between 5 C and 35 C (41 F and 9 F). APPLICATION METHOD Apply with a short nap roller or a brush. Part B has to be blended with the Part A for 2 to 3 minutes until homogeneity is obtained. TEMPERATURE Application temperature: Above 10 C (50 F). The mixture can be used for 15 to 20 minutes at 25 C (77 F). TESTS AND APPROVALS Additional Expertise Balconies EPOXY Product Code Colour ALSAN TRAFIK EP Amber For further information, visit the product page on our website. TRAFIK EP 110

92 ALSAN TRAFIK HP 515 Additional Expertise Balconies PU ALSAN TRAFIK HP 515 is a low-odour two-component polyurethane resin, VOC free, 100% solids, used as a primer on substrates such as concrete and plywood. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application Thickness Coverage rate Container 125 μm (5 mil) wet 37 m 2 (400 ft 2 ) per container 7.1 L Units per skid 60 Storage / service life 24 months when properly stored in original sealed containers. APPLICATION METHOD Apply with a squeegee or a roller. Part B has to be blended with Part A for 2 to 3 minutes until homogeneity is obtained. TEMPERATURE Application temperature: Above 5 C (41 F). The mixture can be used for 15 to 20 minutes at 25 C (77 F). TESTS AND APPROVALS Product Code Colour ALSAN TRAFIK HP Amber TRAFIK HP For further information, visit the product page on our website.

93 ALSAN TRAFIK HP 530 ALSAN TRAFIK HP 530 is a single-component, ready-to-use, polyurethane wear layer that ensures the durability of the TRAFIK HP 500 system. It is installed in one or more layers depending on the traffic density. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application Thickness Coverage rate Container 300 μm (13 mil) wet 56 m 2 (600 ft 2 ) per container 19 L Units per skid 36 Storage / service life 18 months when properly stored in original sealed containers. APPLICATION METHOD Apply with a squeegee or a roller. The wear layer is applied with a squeegee or a roller at the rate of 0.51 L/m 2 (600 ft 2 /19 L) and the aggregate is spread onto the wear layer in order to obtain a non-slip finish. The wear layer must be levelled with a roller and shall have a wet film thickness of 300 micrometers (13 mil) before the application of aggregates. TEMPERATURE Application temperature: Above 5 C (41 F). Additional Expertise Balconies PU Product Code Colour ALSAN TRAFIK HP Grey Dark grey COMPLEMENTARY PRODUCTS COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements. For further information, visit the product page on our website. TRAFIK HP

94 ALSAN TRAFIK HP 540 Additional Expertise Balconies PU ALSAN TRAFIK HP 540 is a single-component aliphatic polyurethane transparent resin finish coat. It provides the TRAFIK HP 500 system with greater durability and facilitates its cleaning. ALSAN TRAFIK HP 540 can be tinted if necessary. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application Thickness Coverage rate Container 250 μm (10 mil) wet 70 m 2 (750 ft 2 ) per container 19 L Units per skid 36 Storage / service life 18 months when properly stored in original sealed containers. APPLICATION METHOD Apply with a roller. When the wear layer is set, the finish coat is applied with a roller at the rate of 70 m 2 /19 L (750 ft 2 /19 L) in order to obtain a wet film thickness of 250 micrometers (10 mil). TEMPERATURE Application temperature: Above 5 C (41 F). Product Code Colour ALSAN TRAFIK HP Clear COMPLEMENTARY PRODUCT ALSAN TRAFIK HP COLORANT is a pigment paste added to ALSAN TRAFIK HP 540. TRAFIK HP For further information, visit the product page on our website.

95 PMMA ALSAN RS Liquid System FINISH COAT COATS PRIMER WEARING COURSE AND PROTECTION COLOURS CLEAR FINISH PRODUCT ALSAN TRAFIK EP 110 ALSAN RS 276 PRIMER ALSAN RS 233 SELF-LEVELING MORTAR ALSAN RS 263 LO SELF-LEVELING MORTAR ALSAN RS 287 COLOR FINISH BASE ALSAN RS 289 TEXTURED BASE ALSAN RS 281 CLEAR FINISH IMAGE APPLICATION METHOD Roller Roller Flat trowel or roller Flat trowel or roller Roller Roller Roller APPLICATION TEMPERATURE Above 10 C Above 3 C Above 3 C Above 3 C Above 3 C Above 3 C Above 3 C DESCRIPTION ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fastdrying primer, increasing the subsequent adhesion of the ALSAN RS system on concrete. ALSAN RS 276 PRIMER is a fast-curing translucent twocomponent primer formulated from polymethyl methacrylate (PMMA) resins. It is used to increase the adhesion of the ALSAN RS system in both indoor and outdoor applications. ALSAN RS 233 SELF- LEVELING MORTAR is a two-component selflevelling mortar made from polymethyl methacrylate (PMMA). This mortar is used for levelling surfaces in combination with the ALSAN RS systems. ALSAN RS 233 SELF-LEVELING MORTAR is composed of the ALSAN RS 210 resin and the ALSAN RS 223 cementitious powder. ALSAN RS 263 LO SELF-LEVELING MORTAR is a two-component polymethacrylate-based (PMA) selflevelling mortar composed of ALSAN RS 240 LO resin and ALSAN RS 223 cementitious powder. The mortar is used to level rough surfaces in conjunction with ALSAN RS systems. Special low-odour formulation improves working conditions and provides considerably less production downtime due to odour related to health and environmental hazards. ALSAN RS 287 COLOR FINISH BASE is a colourless two-component resin composed of polymethyl methacrylate (PMMA) in which ALSAN RS COLOR ADDITIVE coloured paste is added ALSAN RS 289 TEXTURED BASE is a mixture of colourless two-component liquid resin made from polymethyl methacrylate (PMMA) and aggregates (premixed additive) in which an ALSAN RS COLOR ADDITIVE is added. ALSAN RS 281 CLEAR FINISH is a colourless finishing resin made from polymethyl methacrylate (PMMA). It is used as a protective coating when COLORED QUARTZ AGGREGATES or DECO CHIPS are applied. SELECTION FEATURES Vapour barrier Quick setting to meet tight deadlines Waterproofing and protection against water Quick setting to meet tight deadlines No joints Forms a strong protective layer Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C Special low-odour formulation Forms a strong protective layer Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C

96 Additional Expertise Balconies PMMA Partially reinforced light trafficable system over unoccupied, opened and unheated spaces only. ALSAN RS 289 TEXTURED BASE + ALSAN RS COLOR ADDITIVE ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Concrete deck Note: Use ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH with ALSAN RS FLEECE for details and flashings.

97 Additional Expertise Balconies PMMA Partially reinforced light trafficable system over unoccupied, opened and unheated spaces only. ALSAN RS 289 TEXTURED BASE + ALSAN RS COLOR ADDITIVE ALSAN RS 233 SELF-LEVELING MORTAR or ALSAN RS 263 LO SELF-LEVELING MORTAR Concrete deck ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Note: Use ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH with ALSAN RS FLEECE for details and flashings.

98 Additional Expertise Balconies PMMA Partially reinforced light trafficable system over unoccupied, opened and unheated spaces only. ALSAN RS DECO CHIPS at saturation + ALSAN RS 281 CLEAR FINISH ALSAN RS 233 SELF-LEVELING MORTAR or ALSAN RS 263 LO SELF-LEVELING MORTAR Concrete deck ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Note: Use ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH with ALSAN RS FLEECE for details and flashings. For full saturation of ALSAN RS DECO CHIPS, an additional layer of ALSAN RS 281 CLEAR FINISH is required.

99 Additional Expertise Balconies PMMA Partially reinforced light trafficable system over unoccupied, opened and unheated spaces only. ALSAN RS 287 COLOR FINISH BASE ALSAN RS 233 SELF-LEVELING MORTAR or ALSAN RS 263 LO SELF-LEVELING MORTAR NATURAL QUARTZ AGGREGATES Concrete deck ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Note: Use ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH with ALSAN RS FLEECE for details and flashings.

100 Additional Expertise Balconies PMMA Partially reinforced light trafficable system over unoccupied, opened and unheated spaces only. ALSAN RS 281 CLEAR FINISH ALSAN RS 233 SELF-LEVELING MORTAR or ALSAN RS 263 LO SELF-LEVELING MORTAR COLORED QUARTZ AGGREGATES Concrete deck ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Note: Use ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH with ALSAN RS FLEECE for details and flashings.

101 ALSAN TRAFIK EP 110 ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fast-drying primer, increasing the subsequent adhesion of the ALSAN RS system on concrete. Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Thickness Coverage rate per kit 0.25 mm (10 mil) 2 x 0.25 mm (2 x 10 mil) 13 m 2 (140 ft 2 ) with wet film thickness of 0.25 mm (10 mil) 7 m 2 (70 ft 2 ) with wet film thickness of 0.50 mm (20 mil) Units per skid 75 Storage / service life Containers must be stored away from heat, moisture and sunlight. Storage: up to 18 months in original sealed containers at a temperature between 5 C and 35 C (41 F and 95 F). APPLICATION METHOD Apply with a short nap roller or a brush. Part B has to be blended with the Part A for 2 to 3 minutes until homogeneity is obtained. TEMPERATURE Application temperature: Above 10 C (50 F). The mixture can be used for 15 to 20 minutes at 25 C (77 F). TESTS AND APPROVALS Additional Expertise Balconies EPOXY Product Code Colour ALSAN TRAFIK EP Amber For further information, visit the product page on our website. TRAFIK EP 110

102 ALSAN RS 276 PRIMER Additional Expertise Balconies PMMA ALSAN RS 276 PRIMER is a fast-curing, translucent, two-component primer formulated from polymethyl methacrylate (PMMA) resins. It is used to increase the adhesion of the ALSAN RS system in both indoor and outdoor applications. BENEFITS Sealing and protection against water Quick setting to meet tight deadlines No joints Application at temperatures as low as 3 C Thickness Coverage rate mm wet (15-20 mil wet) 25 m 2 (269 ft 2 ) per container APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. The resin must be evenly distributed over the surface. TEMPERATURE Application temperature: Above 3 C (37 F). Container The ALSAN RS 276 PRIMER resin is offered in a 10 kg (22 lb) resealable container with a locking ring. TESTS AND APPROVALS Units per skid 60 Service life / storage 24 months when properly stored in the original sealed container. SOPREMA INC. Product Code ALSAN RS 276 PRIMER * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. ALSAN RS COMPLEMENTARY PRODUCT ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. For further information, visit the product page on our website.

103 ALSAN RS 233 SELF-LEVELING MORTAR ALSAN RS 233 SELF-LEVELING MORTAR is a two-component self-levelling mortar made from polymethyl methacrylate (PMMA). This mortar is used for levelling surfaces in combination with the ALSAN RS systems. ALSAN RS 233 SELF-LEVELING MORTAR is composed of the ALSAN RS 210 resin and the ALSAN RS 223 cementitious powder. BENEFITS Forms a strong protective layer Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C APPLICATION Apply with a flat trowel or a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using a flat trowel or a roller. TEMPERATURE Application temperature: Above 3 C (37 F). Additional Expertise Balconies PMMA Colour Thickness Coverage rate Containers Pebble Grey mm wet (85-95 mil wet) 9 m 2 (100 ft 2 ) per container The ALSAN RS 233 SELF-LEVELING MORTAR is supplied in two parts: The ALSAN RS 210 resin is offered in a 10 kg (22 lb) resealable container with a locking ring. The ALSAN RS 223 powder is offered in a 23 kg (50.7 lb) bag. TESTS AND APPROVALS SOPREMA INC. Units per skid 60 (ALSAN RS 210) / 64 (ALSAN RS 223) Service life / storage 12 months when properly stored in the original sealed packaging. Product Code Products required ALSAN RS 233 SELF-LEVELING MORTAR * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent ALSAN RS 210 SUMMER ALSAN RS 210 WINTER ALSAN RS 223 POWDER For further information, visit the product page on our website. ALSAN RS COMPLEMENTARY PRODUCTS ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS DECO CHIPS polymer flakes are used as decorative elements. COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements.

104 ALSAN RS 263 LO SELF-LEVELING MORTAR Additional Expertise Balconies PMA ALSAN RS 263 LO SELF-LEVELING MORTAR is a two-component polymethacrylatebased (PMA) self-levelling mortar composed of ALSAN RS 240 LO resin and ALSAN RS 223 cementitious powder. The mortar is used to level rough surfaces in conjunction with ALSAN RS systems. Special low-odour formulation improves working conditions and provides considerably less production down time due to odour related to health and environmental hazards. Total minimum consumption Total minimum coverage rate Thickness Coverage rate mm wet (85-95 mil wet) 9 m 2 (100 ft 2 ) per container APPLICATION METHOD Apply with a flat trowel or a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using a flat trowel or a roller. Containers Units per skid Colour Service life / storage The ALSAN RS 263 LO SELF- LEVELING resin is supplied in two parts: in a 10 kg (22 lb)resealable container of ALSAN RS 240 LO with a locking ring and in a 23 kg (50.7 lb) bag of ALSAN RS (ALSAN RS 240 LO) / 64 (ALSAN RS 223) Pebble Grey 12 months when properly stored in the original sealed container. TEMPERATURE Application temperature: Above 3 C (37 F). Product Code Products required ALSAN RS 263 LO SELF-LEVELING MORTAR ALSAN RS 240 LO ALSAN RS 223 POWDER * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. ALSAN RS COMPLEMENTARY PRODUCT ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. For further information, visit the product page on our website.

105 ALSAN RS 287 COLOR FINISH BASE ALSAN RS 287 COLOR FINISH BASE is a colourless two-component resin made from polymethyl methacrylate (PMMA) in which an ALSAN RS COLOR ADDITIVE coloured paste is added. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines No joints Application at temperatures as low as 3 C Thickness APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. TEMPERATURE Application temperature: Above 3 C (37 F). Additional Expertise Balconies PMMA on rough a surface on smooth a surface mm wet (20-25 mil wet) mm wet (12-15 mil wet) Coverage rate on a rough surface 0.5 kg/m 2 (0.046 kg/ft 2 ) on a smooth surface 0.3 kg/m 2 (0.028 kg/ft 2 ) Container The ALSAN RS 287 COLOR FINISH BASE resin is offered in an 8.5 kg (18.7 lb) resealable container with a locking ring. Units per skid 40 Service life / storage 12 months when properly stored in the original sealed container. ALSAN RS 287 COLOR FINISH BASE Product Code Colour * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent Colourless For further information, visit the product page on our website. ALSAN RS COMPLEMENTARY PRODUCTS ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS COLOR ADDITIVE is a coloured paste intended to be added to liquid PMMA resins. ALSAN RS DECO CHIPS polymer flakes are used as decorative elements. COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements.

106 ALSAN RS 289 TEXTURED BASE Additional Expertise Balconies PMMA ALSAN RS 289 TEXTURED BASE is a mixture of colourless two-component liquid resin made from polymethyl methacrylate (PMMA) and aggregates (premixed additive) in which an ALSAN RS COLOR ADDITIVE is added. ALSAN RS 289 TEXTURED BASE is used as a finish coat or a slip-resistant protection with ALSAN RS systems for balconies and roofs. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines Contains aggregates for better slip resistance No joints Application at temperatures as low as 3 C APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. TEMPERATURE Application temperature: Above 3 C (37 F). Thickness Coverage rate Container mm wet (25-30 mil wet) 11 m 2 (120 ft 2 ) per container The ALSAN RS 289 TEXTURED BASE resin is offered in a 13.5 kg (29.8 lb) resealable container with a locking ring. Units per skid 40 Service life / storage 12 months when properly stored in the original sealed container. Product Code Colour ALSAN RS 289 TEXTURED BASE Colourless ALSAN RS * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. COMPLEMENTARY PRODUCTS ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS COLOR ADDITIVE is a coloured paste intended to be added to liquid PMMA resins. For further information, visit the product page on our website.

107 ALSAN RS 281 CLEAR FINISH ALSAN RS 281 CLEAR FINISH is a colourless finishing resin made from polymethyl methacrylate (PMMA). It is used as a protective coating when COLORED QUARTZ AGGREGATES or DECO CHIPS are applied. Thickness on rough surfaces Coverage rate on rough surfaces Containers mm wet (20-25 mil wet) 20 m 2 (215 ft 2 ) per container The ALSAN RS 281 CLEAR FINISH resin is offered in a 10 kg (22 lb) resealable container. Units per skid 60 Service life / storage 12 months when properly stored in the original sealed container. APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. TEMPERATURE Application temperature: Above 3 C (37 F). Additional Expertise Balconies PMMA Product Code Colour ALSAN RS 281 CLEAR FINISH Clear TESTS AND APPROVALS * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. SOPREMA INC. COMPLEMENTARY PRODUCT ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS DECO CHIPS polymer flakes are used as decorative elements. COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements. For further information, visit the product page on our website. ALSAN RS

108

109 PLAZA DECKS

110 PU TRAFIK HP Liquid System COATS PRIMER WATERPROOFING WEAR COAT FINISH COAT PRODUCT ALSAN TRAFIK EP 110 ALSAN TRAFIK HP 515 ALSAN TRAFIK HP 520 ALSAN TRAFIK HP 530 ALSAN TRAFIK HP 540 IMAGE APPLICATION METHOD Roller Squeegee and roller Notched squeegee and roller Squeegee and roller Roller APPLICATION TEMPERATURE Above 10 C Above 5 C Above 5 C Above 5 C Above 5 C DESCRIPTION ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fast-drying primer, increasing the subsequent adhesion of the ALSAN TRAFIK HP 500 system. It is also used for junctions where the ALSAN TRAFIK HP 500 system meets SOPREMA bituminous membranes. ALSAN TRAFIK HP 515 is a low-odour, two-component polyurethane resin, VOC free, 100% solids, used as a primer on substrates such as concrete and plywood. ALSAN TRAFIK HP 520 is a single-component polyurethane resin waterproofing membrane. ALSAN TRAFIK HP 530 is a singlecomponent polyurethane resin wear coat that ensures the durability of the TRAFIK HP 500 system. It is installed in one or more layers depending on the traffic density. ALSAN TRAFIK HP 540 is a singlecomponent aliphatic polyurethane transparent resin finish coat. It provides the TRAFIK HP 500 system with greater durability and facilitates its cleaning. ALSAN TRAFIK HP 540 can be tinted if necessary. SELECTION FEATURES Vapour barrier Quick setting to meet tight deadlines Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application Increased resistance Lightweight and efficient system Elimination of infiltration risk Hassle-free application

111 Additional Expertise Plaza Decks PU Plaza decks ALSAN TRAFIK HP aggregates ALSAN TRAFIK HP 520 Concrete deck ALSAN TRAFIK HP 515 or ALSAN TRAFIK EP 110 Note: To add colour to the system, the Alsan Trafik HP 540 can be used in finish coat

112 ALSAN TRAFIK EP 110 ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fast-drying primer, increasing the subsequent adhesion of the ALSAN TRAFIK HP 500 system on concrete. It is also used for junctions where the ALSAN TRAFIK HP 500 system meets SOPREMA bituminous membranes. Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Thickness Coverage rate per kit 0.25 mm (10 mil) 2 x 0.25 mm (2 x 10 mil) 13 m 2 (140 ft 2 ) with wet film thickness of 0.25 mm (10 mil) 7 m 2 (70 ft 2 ) with wet film thickness of 0.50 mm (20 mil) Units per skid 75 Storage / service life Containers must be stored away from heat, moisture and sunlight. Storage: up to 18 months in original sealed containers at a temperature between 5 C and 35 C (41 F and 95 F). APPLICATION METHOD Apply with a short nap roller or a brush. Part B has to be blended with the Part A for 2 to 3 minutes until homogeneity is obtained. TEMPERATURE Application temperature: Above 10 C (50 F). The mixture can be used for 15 to 20 minutes at 25 C (77 F). TESTS AND APPROVALS Plaza Decks EPOXY Additional Expertise Product Code Colour ALSAN TRAFIK EP Amber For further information, visit the product page on our website. TRAFIK EP 110

113 ALSAN TRAFIK HP 515 Additional Expertise Plaza Decks EPOXY ALSAN TRAFIK HP 515 is a low-odour, two-component polyurethane resin, VOC free, 100% solids, used as a primer on substrates such as concrete and plywood. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application Thickness Coverage rate Container 125 μm (5 mil) wet 37 m 2 (400 ft 2 ) per container 7.1 L Units per skid 60 Storage / service life 24 months when properly stored in original sealed containers. APPLICATION METHOD Apply with a squeegee or a roller. Part B has to be blended with Part A for 2 to 3 minutes until homogeneity is obtained. TEMPERATURE Application temperature: Above 5 C (41 F). The mixture can be used for 15 to 20 minutes at 25 C (77 F). TESTS AND APPROVALS Product Code Colour ALSAN TRAFIK HP Amber TRAFIK HP For further information, visit the product page on our website.

114 ALSAN TRAFIK HP 520 ALSAN TRAFIK HP 520 is a single-component, ready-to-use, polyurethane waterproofing membrane. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application Thickness Coverage rate Container 700 μm (28 mil) wet 28 m 2 (300 ft 2 ) per container 19 L Units per skid 36 Storage / service life 18 months when properly stored in original sealed containers. APPLICATION METHOD Apply with a notched squeegee or a roller. When the primer is set, the waterproofing membrane is applied with a 6 mm notched squeegee at the rate of 0.68 L/m 2 (300 ft 2 /19 L) and must be levelled with a roller. Membrane thickness shall have a wet film thickness of 700 micrometers (28 mil). TEMPERATURE Application temperature: Above 5 C (41 F). PU Plaza Decks Additional Expertise Product Code Colour ALSAN TRAFIK HP Grey COMPLEMENTARY PRODUCT ALSAN TRAFIK HP ACCELERATOR is added to ALSAN TRAFIK HP 520 to accelerate the drying time of the liquid waterproofing membrane. For further information, visit the product page on our website. TRAFIK HP

115 ALSAN TRAFIK HP 530 Additional Expertise PU Plaza Decks ALSAN TRAFIK HP 530 is a single-component, ready-to-use, polyurethane wear layer that ensures the durability of the TRAFIK HP 500 system. It is installed in one or more layers depending on the traffic density. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application Thickness Coverage rate Container 300 μm (13 mil) wet 56 m 2 (600 ft 2 ) per container 19 L Units per skid 36 Storage / service life 18 months when properly stored in original sealed containers. APPLICATION METHOD Apply with a squeegee or a roller. When the waterproofing membrane is set, the wear layer is applied with a squeegee or a roller at the rate of 0.51 L/m 2 (600 ft 2 /19 L) and the aggregate is spread onto the wear layer in order to obtain a non-slip finish. The wear layer must be levelled with a roller and shall have a wet film thickness of 300 micrometers (13 mil) before the application of aggregates. TEMPERATURE Application temperature: Above 5 C (41 F). Product Code Colour ALSAN TRAFIK HP Grey Dark grey TRAFIK HP COMPLEMENTARY PRODUCTS COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements. For further information, visit the product page on our website.

116 ALSAN TRAFIK HP 540 ALSAN TRAFIK HP 540 is a single-component aliphatic polyurethane transparent resin finish coat. It provides the TRAFIK HP 500 system with greater durability and facilitates its cleaning. ALSAN TRAFIK HP 540 can be tinted if necessary. BENEFITS Increased resistance Lightweight and efficient system Elimination of infiltration risks Hassle-free application Thickness Coverage rate Container 250 μm (10 mil) wet 70 m 2 (750 ft 2 ) per container 19 L Units per skid 36 Storage / service life 18 months when properly stored in original sealed containers. APPLICATION METHOD Apply with a roller. When the wear layer is set, the finish coat is applied with a roller at the rate of 70 m 2 /19 L (750 ft 2 /19 L) in order to obtain a wet film thickness of 250 micrometers (10 mil). TEMPERATURE Application temperature: Above 5 C (41 F). PU Plaza Decks Additional Expertise Product Code Colour ALSAN TRAFIK HP Clear COMPLEMENTARY PRODUCT ALSAN TRAFIK HP COLORANT is a pigment paste added to ALSAN TRAFIK HP 540. For further information, visit the product page on our website. TRAFIK HP

117 PMMA ALSAN RS Liquid System FINISH COAT COATS PRIMER WATERPROOFING WEARING COURSE AND PROTECTION COLOURS CLEAR FINISH PRODUCT ALSAN TRAFIK EP 110 ALSAN RS 222 PRIMER ALSAN RS 276 PRIMER ALSAN RS 230 FIELD GRADE Summer Winter Summer Winter ALSAN RS 230 FLASH ALSAN RS 260 LO FIELD ALSAN RS 260 LO FLASH ALSAN RS 233 SELF-LEVELING MORTAR ALSAN RS 263 LO SELF-LEVELING MORTAR ALSAN RS 287 COLOR FINISH BASE ALSAN RS 289 TEXTURED BASE ALSAN RS 281 CLEAR FINISH IMAGE APPLICATION METHOD Roller Roller Roller Roller Roller Roller Roller Flat trowel or roller Flat trowel or roller Roller Roller Roller APPLICATION TEMPERATURE Above 10 C Above 3 C Above 3 C Above 15 C Above -5 C Above 15 C Above -5 C Above 3 C Above 3 C Above 3 C Above 3 C Above 3 C Above 3 C Above 3 C DESCRIPTION ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fast-drying primer, increasing the subsequent adhesion of the ALSAN RS system on concrete. ALSAN RS 222 PRIMER is a fastcuring, translucent, two-component primer formulated from polymethyl methacrylate (PMMA) resins. It is used to increase the adhesion of the ALSAN RS over substrates such as asphaltic and roof cover boards. ALSAN RS 276 PRIMER is a fastcuring translucent two-component primer formulated from polymethyl methacrylate (PMMA) resins. It is used to increase the adhesion of the ALSAN RS system in both indoor and outdoor applications. ALSAN RS 230 FIELD is a two-component liquid membrane composed of polymethyl methacrylate (PMMA). It is combined with a textile reinforcement to form a reinforced, monolithic, self-adhesive membrane designed for waterproofing new surfaces or surfaces under repair, whether for indoor or outdoor applications. ALSAN RS 230 FLASH is a two-component liquid membrane composed of polymethyl methacrylate (PMMA). It is combined with a textile reinforcement to form a reinforced, monolithic, selfflashing membrane designed for waterproofing elevations and details in both indoor and outdoor applications. ALSAN RS 260 LO FIELD is a two-component liquid membrane composed of polymethacrylate (PMA). It combines a resin and textile reinforcement to form a reinforced, monolithic, selfadhesive membrane used for waterproofing new surfaces or surfaces under repair, whether for indoor or outdoor applications. Special low-odour formulation improves working conditions and provides considerably less production downtime due to odour related to health and environmental hazards. ALSAN RS 260 LO FLASH is a two-component liquid membrane composed of polymethacrylate (PMA). It combines a resin and textile reinforcement to form a reinforced, monolithic, selfadhesive membrane used for waterproofing elevations and details in both indoor and outdoor applications. Special low-odour formulation improves working conditions and provides considerably less production downtime due to odour related to health and environmental hazards. ALSAN RS 233 SELF- LEVELING MORTAR is a two-component selflevelling mortar made from polymethyl methacrylate (PMMA). This mortar is used for levelling surfaces in combination with the ALSAN RS systems. ALSAN RS 233 SELF-LEVELING MORTAR is composed of the ALSAN RS 210 resin and the ALSAN RS 223 cementitious powder. ALSAN RS 263 LO SELF-LEVELING MORTAR is a two-component polymethacrylate-based (PMA) self-levelling mortar composed of ALSAN RS 240 LO resin and ALSAN RS 223 cementitious powder. The mortar is used to level rough surfaces in conjunction with ALSAN RS systems. Special low-odour formulation improves working conditions and provides considerably less production downtime due to odour related to health and environmental hazards. ALSAN RS 287 COLOR FINISH BASE is a colourless two-component resin composed of polymethyl methacrylate (PMMA) in which ALSAN RS COLOR ADDITIVE coloured paste is added ALSAN RS 289 TEXTURED BASE is a mixture of colourless two-component liquid resin made from polymethyl methacrylate (PMMA) and aggregates (premixed additive) in which an ALSAN RS COLOR ADDITIVE is added. ALSAN RS 281 CLEAR FINISH is a colourless finishing resin made from polymethyl methacrylate (PMMA). It is used as a protective coating when COLORED QUARTZ AGGREGATES or DECO CHIPS are applied. SELECTION FEATURES Vapour barrier Quick setting to meet tight deadlines Waterproofing and protection against water Quick setting to meet tight deadlines No joints Waterproofing and protection against water Quick setting to meet tight deadlines No joints Waterproofing and protection against water Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 15 C for summer grade, and -5 C for winter grade Polyester reinforced Waterproofing and protection against water Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 15 C for summer grade, and -5 C for winter grade Polyester reinforced Special low-odour formulation Waterproofing and protection against water Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C Polyester reinforced Special low-odour formulation Waterproofing and protection against water Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C Polyester reinforced Forms a strong protective layer Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C Special low-odour formulation Forms a strong protective layer Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C

118 Additional Expertise Plaza Decks PMMA Fully reinforced trafficable system with texture finish ALSAN RS 289 TEXTURED BASE + ALSAN RS COLOR ADDITIVE ALSAN RS 233 SELF-LEVELING MORTAR or ALSAN RS 263 LO SELF-LEVELING MORTAR ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD ALSAN RS FLEECE ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD Concrete deck ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Note: Use ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH with ALSAN RS FLEECE for details and flashings.

119 Additional Expertise Plaza Decks PMMA Fully reinforced trafficable system with colour finish and deco chips ALSAN RS 287 COLOR FINISH BASE with ALSAN RS DECO CHIPS + ALSAN RS COLOR ADDITIVE ALSAN RS 233 SELF-LEVELING MORTAR or ALSAN RS 263 LO SELF-LEVELING MORTAR ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD ALSAN RS FLEECE ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD Concrete deck ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Note: Use ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH with ALSAN RS FLEECE for details and flashings. For full saturation of ALSAN RS DECO CHIPS, an additional layer of ALSAN RS 281 CLEAR FINISH is required.

120 Additional Expertise Plaza Decks PMMA Fully reinforced trafficable system with quartz and colour finish ALSAN RS 287 COLOR FINISH BASE + ALSAN RS COLOR ADDITIVE ALSAN RS 233 SELF-LEVELING MORTAR or ALSAN RS 263 LO SELF-LEVELING MORTAR AGRÉGATS DE QUARTZ NATURELS ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD ALSAN RS FLEECE ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD Concrete deck ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Note: Use ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH with ALSAN RS FLEECE for details and flashings.

121 Additional Expertise Plaza Decks PMMA Fully reinforced trafficable system with color quartz and clear finish ALSAN RS 281 CLEAR FINISH ALSAN RS 233 SELF-LEVELING MORTAR or ALSAN RS 263 LO SELF-LEVELING MORTAR COLORED QUARTZ AGGREGATES ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD ALSAN RS FLEECE ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD Concrete deck ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Note: Use ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH with ALSAN RS FLEECE for details and flashings.

122 ALSAN TRAFIK EP 110 ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fast-drying primer, increasing the subsequent adhesion of the ALSAN RS system on concrete. Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Thickness Coverage rate per kit 0.25 mm (10 mil) 2 x 0.25 mm (2 x 10 mil) 13 m 2 (140 ft 2 ) with wet film thickness of 0.25 mm (10 mil) 7 m 2 (70 ft 2 ) with wet film thickness of 0.50 mm (20 mil) Units per skid 75 Storage / service life Containers must be stored away from heat, moisture and sunlight. Storage: up to 18 months in original sealed containers at a temperature between 5 C and 35 C (41 F and 95 F). APPLICATION METHOD Apply with a short nap roller or a brush. Part B has to be blended with the Part A for 2 to 3 minutes until homogeneity is obtained. TEMPERATURE Application temperature: Above 10 C (50 F). The mixture can be used for 15 to 20 minutes at 25 C (77 F). TESTS AND APPROVALS EPOXY Plaza Decks Additional Expertise Product Code Colour ALSAN TRAFIK EP Amber For further information, visit the product page on our website. TRAFIK EP 110

123 ALSAN RS 222 PRIMER Additional Expertise Plaza Decks PMMA ALSAN RS 222 PRIMER is a fast-curing, translucent, two-component primer formulated from polymethyl methacrylate (PMMA) resins. It is used to increase the adhesion of the ALSAN RS over substrates such as asphaltic and roof cover boards. BENEFITS Sealing and protection against water Quick setting to meet tight deadlines No joints Application at temperatures as low as 3 C Thickness Coverage rate mm wet (15-20 mil wet) 25 m 2 (269 ft 2 ) per container APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. The resin must be evenly distributed over the surface. TEMPERATURE Application temperature: Above 3 C (37 F). Container The ALSAN RS 222 PRIMER resin is offered in a 10 kg (22 lb) resealable container with a locking ring. TESTS AND APPROVALS Units per skid 60 Service life / storage 12 months when properly stored in the original sealed container. SOPREMA INC. Product Code ALSAN RS 222 PRIMER * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. ALSAN RS COMPLEMENTARY PRODUCT ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. For further information, visit the product page on our website.

124 ALSAN RS 276 PRIMER ALSAN RS 276 PRIMER is a fast-curing, translucent, two-component primer formulated from polymethyl methacrylate (PMMA) resins. It is used to increase the adhesion of the ALSAN RS system in both indoor and outdoor applications. BENEFITS Sealing and protection against water Quick setting to meet tight deadlines No joints Application at temperatures as low as 3 C Thickness Coverage rate mm wet (15-20 mil wet) 25 m 2 (269 ft 2 ) per container APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. The resin must be evenly distributed over the surface. TEMPERATURE Application temperature: Above 3 C (37 F). PMMA Plaza Decks Additional Expertise Container The ALSAN RS 276 PRIMER resin is offered in a 10 kg (22 lb) resealable container with a locking ring. TESTS AND APPROVALS Units per skid 60 Service life / storage 24 months when properly stored in the original sealed container. SOPREMA INC. Product Code ALSAN RS 276 PRIMER * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. COMPLEMENTARY PRODUCT ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. For further information, visit the product page on our website. ALSAN RS

125 ALSAN RS 230 FIELD Additional Expertise PMMA Plaza Decks ALSAN RS 230 FIELD is a two-component liquid membrane composed of polymethyl methacrylate (PMMA). ALSAN RS 230 FIELD is combined with a textile reinforcement to form a reinforced, monolithic, self-adhesive membrane designed for waterproofing new surfaces or surfaces under repair, whether for indoor or outdoor applications. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines Flexible No joints Application at minimal temperatures of 15 C for summer grade, and as low as -5 C for winter grade Polyester reinforced APPLICATION METHOD After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers, brushes or a SOPREMA notched squeegee. The resin must be evenly distributed over the surface. TEMPERATURE Total minimum consumption Consumption of the base coat Consumption of the finish coat Total minimum coverage rate Thickness Coverage rate mm wet (72-86 mil wet) mm wet (56-60 mil wet) mm wet (22-26 mil wet) 3.0 kg/m 2 (0.28 kg/ft 2 ), approximately 8 m 2 (90 ft 2 ) per container Summer grade: The ALSAN RS 230 FIELD membrane can be applied at a substrate temperature between 15 C (59 F) and 50 C (122 F), and an ambient temperature between 15 C (59 F) and 40 C (104 F). Winter grade: The ALSAN RS 230 FIELD membrane can be applied at a substrate temperature between -5 C (23 F) and 20 C (68 F), and an ambient temperature between -5 C (23 F) and 20 C (68 F). Coverage rate of the base coat 2.0 kg/m 2 (0.19 kg/ft 2 ) ALSAN RS Coverage rate of the finish coat 1.0 kg/m 2 (0.09 kg/ft 2 ) Container The ALSAN RS 230 FIELD resin is offered in a 25 kg (55 lb) resealable container with a locking ring. Units per skid 24 Service life / storage 12 months when properly stored in the original sealed container. Product Code Grade Colour TESTS AND APPROVALS SOPREMA INC. For further information, visit the product page on our website. ALSAN RS 230 FIELD Summer grade Pebble Grey Summer grade Traffic White Winter grade Pebble Grey Winter grade Traffic White * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. * The thickness of the polyester reinforcement is not taken into account in the thickness; the measure is only for the liquid resin. COMPLEMENTARY PRODUCTS ALSAN RS FLEECE is used to improve the resistance of resins to tearing and puncture. ALSAN RS DETAILER is used as a waterproof paste in locations where it is difficult to install a liquid membrane system with reinforcement. ALSAN RS PASTE is used as a mastic for sealing cracks, depressions and gaps before installing liquid membranes. ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application.

126 ALSAN RS 230 FLASH ALSAN RS 230 FLASH is a two-component liquid membrane composed of polymethyl methacrylate (PMMA). It is combined with a textile reinforcement to form a reinforced, monolithic, self-flashing membrane designed for waterproofing elevations and details in both indoor and outdoor applications. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines Flexible No joints Application at minimal temperatures of 15 C for summer grade, and as low as -5 C for winter grade Polyester reinforced Total minimum consumption Consumption of the base coat Consumption of the finish coat Thickness Coverage rate mm wet (72-86 mil wet) mm wet (56-60 mil wet) mm wet (22-26 mil wet) APPLICATION METHOD After mixing, apply the resin on the clean substrate, prepared for the intended purpose, using brushes or rollers. The resin must be evenly distributed over the surface. TEMPERATURE Summer grade: ALSAN RS 230 FLASH membrane can be applied at a substrate temperature between 15 C (59 F) and 50 C (122 F), and an ambient temperature between 15 C (59 F) and 35 C (95 F). Winter grade: ALSAN RS 230 FLASH membrane can be applied at a substrate temperature between -5 C (23 F) and 20 C (68 F), and an ambient temperature between -5 C (23 F) and 20 C (68 F). PMMA Plaza Decks Additional Expertise Total minimum coverage rate 3.0 kg/m 2 (0.28 kg/ft 2 ), approximately 4 m 2 (43 ft 2 ) per container Coverage rate of the base coat 2.0 kg/m 2 (0.19 kg/ft 2 ) TESTS AND APPROVALS Coverage rate of the finish coat 1.0 kg/m 2 (0.09 kg/ft 2 ) Container The ALSAN RS 230 FLASH resin is offered in a 12 kg (26 lb) resealable container with a locking ring. Units per skid 60 Service life / storage 12 months when properly stored in the original sealed container. SOPREMA INC. For further information, visit the product page on our website. ALSAN RS PRODUCT Code Grade Colour Summer grade Pebble Grey ALSAN RS 230 FLASH Summer grade Traffic White Winter grade Pebble Grey Winter grade Traffic White * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. * The thickness of the polyester reinforcement is not taken into account in the thickness; the measure is only for the liquid resin. COMPLEMENTARY PRODUCTS ALSAN RS FLEECE is used to improve the resistance of resins to tearing and puncture. ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application.

127 ALSAN RS 260 LO FIELD Additional Expertise PMA Plaza Decks ALSAN RS 260 LO FIELD is a two-component liquid membrane composed of polymethacrylate (PMA). It combines a resin and textile reinforcement to form a reinforced, monolithic, self-adhesive membrane used for waterproofing new surfaces or surfaces under repair, whether for indoor or outdoor applications. Special low-odour formulation improves working conditions and provides considerably less production down time due to odour related to health and environmental hazards. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines Flexible No joints APPLICATION METHOD After mixing, apply the resin on the clean substrate, prepared for the intended purpose, using brushes or rollers. The resin must be evenly distributed over the surface. Application at temperatures as low as 3 C Polyester reinforced TEMPERATURE Total minimum consumption Thickness mm wet (72-86 mil wet) Application temperature: Above 3 C (37 F). TESTS AND APPROVALS Consumption of the base coat Consumption of the finish coat mm wet (56-60 mil wet) mm wet (22-26 mil wet) Coverage rate SOPREMA INC. Total minimum coverage rate 3.0 kg/m 2 (0.28 kg/ft 2 ), approximately 8 m 2 (90 ft 2 ) per container ALSAN RS Coverage rate of the base coat 2.0 kg/m 2 (0.19 kg/ft 2 ) Coverage rate of the finish coat 1.0 kg/m 2 (0.09 kg/ft 2 ) Container The ALSAN RS 260 LO FIELD resin is offered in a 25 kg (55 lb) resealable container with a locking ring. Units per skid 24 Service life / storage 12 months when properly stored in the original sealed container. For further information, visit the product page on our website. Product Code Colour ALSAN RS 260 LO FIELD Pebble Grey Traffic White * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. * The thickness of the polyester reinforcement is not taken into account in the thickness; the measure is only for the liquid resin. COMPLEMENTARY PRODUCTS ALSAN RS FLEECE is used to improve the resistance of resins to tearing and puncture. ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS DETAILER is used as a waterproof paste in locations where it is difficult to install a liquid membrane system with reinforcement. ALSAN RS PASTE is used as mastic for sealing cracks, depressions and gaps before installing liquid membranes.

128 ALSAN RS 260 LO FLASH ALSAN RS 260 LO FLASH is a two-component liquid membrane composed of polymethacrylate (PMA). It combines a resin and textile reinforcement to form a reinforced, monolithic, self-adhesive membrane used for waterproofing elevations and details in both indoor and outdoor applications. Special low-odour formulation improves working conditions and provides considerably less production down time due to odour related to health and environmental hazards. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C APPLICATION After mixing, apply the resin on the clean substrate prepared for the intended purpose, using brushes or rollers. The resin must be evenly distributed over the surface. PMA Plaza Decks Additional Expertise Polyester reinforced TEMPERATURE Application temperature: Above 3 C (37 F). Thickness TESTS AND APPROVALS Total minimum consumption Consumption of the base coat Consumption of the finish coat mm wet (72-86 mil wet) mm wet (56-60 mil wet) mm wet (22-26 mil wet) SOPREMA INC. Coverage rate Total minimum coverage rate 3.0 kg/m 2 (0.28 kg/ft 2 ), approximately 4 m 2 (43 ft 2 ) per container Coverage rate of the base coat 2.0 kg/m 2 (0.19 kg/ft 2 ) Coverage rate of the finish coat 1.0 kg/m 2 (0.09 kg/ft 2 ) Container The ALSAN RS 260 LO FLASH resin is offered in a 12 kg (26 lb) resealable container with a locking ring. Units per skid 60 For further information, visit the product page on our website. ALSAN RS Service life / storage 12 months when properly stored in the original sealed container. Product Code Colour ALSAN RS 260 LO FLASH Pebble Grey Traffic White * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. * The thickness of the polyester reinforcement is not taken into account in the thickness; the measure is only for the liquid resin. COMPLEMENTARY PRODUCTS ALSAN RS FLEECE is used to improve the resistance of resins to tearing and puncture. ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application.

129 ALSAN RS 233 SELF-LEVELING MORTAR Additional Expertise PMMA Plaza Decks ALSAN RS 233 SELF-LEVELING MORTAR is a two-component self-leveling mortar made from polymethyl methacrylate (PMMA). This mortar is used for leveling surfaces in combination with the ALSAN RS systems. ALSAN RS 233 SELF-LEVELING MORTAR is composed of the ALSAN RS 210 resin and the ALSAN RS 223 cementitious powder. BENEFITS Forms a strong protective layer Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C APPLICATION Apply with a flat trowel or a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using a flat trowel or a roller. TEMPERATURE Application temperature: Above 3 C (37 F). Colour Thickness Coverage rate Containers Pebble Grey mm wet (85-95 mil wet) 9 m 2 (100 ft 2 ) per container The ALSAN RS 233 SELF-LEVELING MORTAR is supplied in two parts: The ALSAN RS 210 resin is offered in a 10 kg (22 lb) resealable container with a locking ring. The ALSAN RS 223 powder is offered in a 23 kg (50.7 lb) bag. TESTS AND APPROVALS SOPREMA INC. Units per skid 60 (ALSAN RS 210) / 64 (ALSAN RS 223) Service life / storage 12 months when properly stored in the original sealed packaging. ALSAN RS Product Code Products required ALSAN RS 233 SELF-LEVELING MORTAR * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent ALSAN RS 210 SUMMER ALSAN RS 210 WINTER ALSAN RS 223 POWDER For further information, visit the product page on our website. COMPLEMENTARY PRODUCTS ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS DECO CHIPS polymer flakes are used as decorative elements. COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements.

130 ALSAN RS 263 LO SELF-LEVELING MORTAR ALSAN RS 263 LO SELF-LEVELING MORTAR is a two-component polymethacrylatebased (PMA) self-levelling mortar composed of ALSAN RS 240 LO resin and ALSAN RS 223 cementitious powder. The mortar is used to level rough surfaces in conjunction with ALSAN RS systems. Special low-odour formulation improves working conditions and provides considerably less production downtime due to odour related to health and environmental hazards. Total minimum consumption Total minimum coverage rate Thickness Coverage rate mm wet (85-95 mil wet) 9 m 2 (100 ft 2 ) per container APPLICATION METHOD Apply with a flat trowel or a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using a flat trowel or a roller. PMA Plaza Decks Additional Expertise Containers Units per skid Colour Service life / storage The ALSAN RS 263 LO SELF-LEVELING resin is supplied in two parts: in a 10 kg (22 lb)resealable container of ALSAN RS 240 LO with a locking ring and in a 23 kg (50.7 lb) bag of ALSAN RS (ALSAN RS 240 LO) / 64 (ALSAN RS 223) Pebble Grey 12 months when properly stored in the original sealed container. TEMPERATURE Application temperature: Above 3 C (37 F). Product Code Products required ALSAN RS 263 LO SELF-LEVELING MORTAR ALSAN RS 240 LO ALSAN RS 223 POWDER * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. COMPLEMENTARY PRODUCT ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. For further information, visit the product page on our website. ALSAN RS

131 ALSAN RS 287 COLOR FINISH BASE Additional Expertise PMMA Plaza Decks ALSAN RS 287 COLOR FINISH BASE is a colourless two-component resin made from polymethyl methacrylate (PMMA) in which an ALSAN RS COLOR ADDITIVE coloured paste is added. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines No joints Application at temperatures as low as 3 C Thickness APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. TEMPERATURE Application temperature: Above 3 C (37 F). on a rough surface on a smooth surface mm wet (20-25 mil wet) mm wet (12-15 mil wet) Coverage rate on a rough surface 0.5 kg/m 2 (0.046 kg/ft 2 ) on a smooth surface 0.3 kg/m 2 (0.028 kg/ft 2 ) Container The ALSAN RS 287 COLOR FINISH BASE resin is offered in an 8.5 kg (18.7 lb) resealable container with a locking ring. Units per skid 40 Service life / storage 12 months when properly stored in the original sealed container. Product Code Colour ALSAN RS 287 COLOR FINISH BASE Colourless ALSAN RS * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. For further information, visit the product page on our website. COMPLEMENTARY PRODUCTS ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS COLOR ADDITIVE is a coloured paste intended to be added to liquid PMMA resins. ALSAN RS DECO CHIPS polymer flakes are used as decorative elements. COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements.

132 ALSAN RS 289 TEXTURED BASE ALSAN RS 289 TEXTURED BASE is a mixture of colourless two-component liquid resin made from polymethyl methacrylate (PMMA) and aggregates (premixed additive) in which an ALSAN RS COLOR ADDITIVE is added. ALSAN RS 289 TEXTURED BASE is used as a finish coat or a slip-resistant protection with ALSAN RS systems for balconies and roofs. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines Contains aggregates for better slip resistance No joints Application at temperatures as low as 3 C APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. TEMPERATURE Application temperature: Above 3 C (37 F). PMMA Plaza Decks Additional Expertise Thickness Coverage rate Container mm wet (25-30 mil wet) 11 m 2 (120 ft 2 ) per container The ALSAN RS 289 TEXTURED BASE resin is offered in a 13.5 kg (29.8 lb) resealable container with a locking ring. Units per skid 40 Service life / storage 12 months when properly stored in the original sealed container. Product Code Colour ALSAN RS 289 TEXTURED BASE Colourless * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. COMPLEMENTARY PRODUCTS ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS COLOR ADDITIVE is a coloured paste intended to be added to liquid PMMA resins. For further information, visit the product page on our website. ALSAN RS

133 ALSAN RS 281 CLEAR FINISH Additional Expertise Plaza Decks PMMA ALSAN RS 281 CLEAR FINISH is a colourless finishing resin made from polymethyl methacrylate (PMMA). It is used as a protective coating when COLORED QUARTZ AGGREGATES or DECO CHIPS are applied. Thickness on rough surfaces Coverage rate on rough surfaces Containers mm wet (20-25 mil wet) 20 m 2 (215 ft 2 ) per container The ALSAN RS 281 CLEAR FINISH resin is offered in a 10 kg (22 lb) resealable container. Units per skid 60 Service life / storage 12 months when properly stored in the original sealed container. APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. TEMPERATURE Application temperature: Above 3 C (37 F). Product Code Colour ALSAN RS 281 CLEAR FINISH Clear TESTS AND APPROVALS * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. COMPLEMENTARY PRODUCT SOPREMA INC. ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS DECO CHIPS polymer flakes are used as decorative elements. COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements. SOPRASEAL For further information, visit the product page on our website.

134 COLPHENE Waterproofing TABLE ADDITIONAL EXPERTISE TYPE SHEET MEMBRANE PRODUCT COLPHENE FLAM 180 IMAGE REINFORCEMENT APPLICATION METHOD APPLICATION TEMPERATURE DESCRIPTION SELECTION FEATURES Non-woven polyester Heat-welded Above -35 C The COLPHENE FLAM 180 membrane is composed of a non-woven polyester reinforcement and SBS bitumen. The surface and underface are covered with a thermofusible plastic film. COLPHENE FLAM 180 is used as a waterproofing membrane on concrete foundation walls, plaza decks and other below-grade concrete walls in horizontal or vertical applications. Installation possible even in cold weather Excellent puncture and tear resistance PLAZA DECKS BITUMEN

135 Additional Expertise Plaza Decks Bitumen Plaza Decks COLPHENE FLAM 180 Concrete SOPRADRAIN COLPHENE FLAM 180 Concrete deck ELASTOCOL 500

136 COLPHENE FLAM 180 The COLPHENE FLAM 180 membrane is composed of a non-woven polyester reinforcement and SBS modified bitumen. The surface and underface are covered with a thermofusible plastic film. COLPHENE FLAM 180 is used as a waterproofing membrane on concrete foundation walls, plaza decks and other below-grade concrete walls in horizontal or vertical applications. BENEFITS Installation possible even in cold weather Excellent puncture and tear resistance Surface Underface Reinforcement Bitumen Thickness Thermofusible plastic film Thermofusible plastic film Non-woven polyester SBS modified 3.0 mm (120 mil) APPLICATION METHOD Heat-welded TESTS AND APPROVALS Heat-Welded Additional Expertise Plaza Decks Product Code Dimensions COLPHENE FLAM 180 Rolls per skid Roll weight x 1 m (33 x 3.3 ft) kg (79 lb) x 1 m (39 x 3.3 ft) kg (97 lb) COMPLEMENTARY PRODUCTS ELASTOCOL 500 and ELASTOCOL 350 are primers used to improve the adhesion of torch-applied waterproofing membranes. SOPRADRAIN 10-G, SOPRADRAIN 15-G, SOPRADRAIN 18-G, SOPRADRAIN ECO-VENT and SOPRADRAIN ECO-2 are high-density drainage boards used in combination with SOPREMA waterproofing products. For further information, visit the product page on our website. COLPHENE

137 Typical Details

138 COLPHENE FLAM 180 Copyrght 2014 SOPREMA Title Drawing Number Scale Plaza Deck / Upstand Terminations BGW17 N.T.S.

139

140 FOUNTAINS PONDS

141 PMMA ALSAN RS Liquid System FINISH COAT COATS PRIMER WATERPROOFING COLOURS CLEAR FINISH PRODUCT ALSAN RS 230 FIELD ALSAN RS 230 FLASH ALSAN TRAFIK EP 110 ALSAN RS 276 PRIMER GRADE Summer Winter Summer Winter ALSAN RS 260 LO FIELD ALSAN RS 260 LO FLASH ALSAN RS 287 COLOR FINISH BASE ALSAN RS 281 CLEAR FINISH IMAGE APPLICATION METHOD Roller Roller Roller Roller Roller Roller Roller Roller APPLICATION TEMPERATURE Above 10 C Above 3 C Above 15 C Above -5 C Above 15 C Above -5 C Above 3 C Above 3 C Above 3 C Above 3 C DESCRIPTION ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fastdrying primer, increasing the subsequent adhesion of the ALSAN RS system on concrete. ALSAN RS 276 PRIMER is a fast-curing translucent twocomponent primer formulated from polymethyl methacrylate (PMMA) resins. It is used to increase the adhesion of the ALSAN RS system in both indoor and outdoor applications. ALSAN RS 230 FIELD is a two-component liquid membrane composed of polymethyl methacrylate (PMMA). It is combined with a textile reinforcement to form a reinforced, monolithic, selfadhesive membrane designed for waterproofing new surfaces or surfaces under repair, whether for indoor or outdoor applications. ALSAN RS 230 FLASH is a two-component liquid membrane composed of polymethyl methacrylate (PMMA). It is combined with a textile reinforcement to form a reinforced, monolithic, selfflashing membrane designed for waterproofing elevations and details in both indoor and outdoor applications. ALSAN RS 260 LO FIELD is a two-component liquid membrane composed of polymethacrylate (PMA). It combines a resin and textile reinforcement to form a reinforced, monolithic, selfadhesive membrane used for waterproofing new surfaces or surfaces under repair, whether for indoor or outdoor applications. Special low-odour formulation improves working conditions and provides considerably less production downtime due to odour related to health and environmental hazards. ALSAN RS 260 LO FLASH is a two-component liquid membrane composed of polymethacrylate (PMA). It combines a resin and textile reinforcement to form a reinforced, monolithic, selfadhesive membrane used for waterproofing elevations and details in both indoor and outdoor applications. Special low-odour formulation improves working conditions and provides considerably less production downtime due to odour related to health and environmental hazards. ALSAN RS 287 COLOR FINISH BASE is a colourless twocomponent resin composed of polymethyl methacrylate (PMMA) in which ALSAN RS COLOR ADDITIVE coloured paste is added ALSAN RS 281 CLEAR FINISH is a colourless finishing resin made from polymethyl methacrylate (PMMA). It is used as a protective coating when COLORED QUARTZ AGGREGATES or DECO CHIPS are applied. SELECTION FEATURES Vapour barrier Quick setting to meet tight deadlines Waterproofing and protection against water Quick setting to meet tight deadlines No joints Waterproofing and protection against water Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 15 C for summer grade, and -5 C for winter grade Polyester reinforced Waterproofing and protection against water Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 15 C for summer grade, and -5 C for winter grade Polyester reinforced Special low-odour formulation Waterproofing and protection against water Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C Polyester reinforced Special low-odour formulation Waterproofing and protection against water Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C Polyester reinforced

142 Additional Expertise Fountains Ponds PMMA Fountains with a smooth coloured finish ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH ALSAN RS 287 COLOR FINISH BASE + ALSAN RS COLOR ADDITIVE ALSAN RS FLEECE ALSAN RS FLEECE ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Concrete deck

143 Additional Expertise Fountains Ponds PMMA Fountains with coloured quartz and clear finish ALSAN RS 230 FLASH or ALSAN RS 260 LO FLASH ALSAN RS 281 CLEAR FINISH COLORED QUARTZ AGGREGATES ALSAN RS FLEECE ALSAN RS FLEECE ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD ALSAN RS 230 FIELD or ALSAN RS 260 LO FIELD ALSAN TRAFIK EP 110 or ALSAN RS 276 PRIMER Concrete deck

144 ALSAN TRAFIK EP 110 ALSAN TRAFIK EP 110 is a low-odour, two-component epoxy primer with low VOC contents. It is used as a fast-drying primer, increasing the subsequent adhesion of the ALSAN RS system on concrete. Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Relative humidity of the concrete: < 85% Relative humidity of the concrete: 85 to 98% Thickness Coverage rate per kit 0.25 mm (10 mil) 2 x 0.25 mm (2 x 10 mil) 13 m 2 (140 ft 2 ) with wet film thickness of 0.25 mm (10 mil) 7 m 2 (70 ft 2 ) with wet film thickness of 0.50 mm (20 mil) Units per skid 75 Storage / service life Containers must be stored away from heat, moisture and sunlight. Storage: up to 18 months in original sealed containers at a temperature between 5 C and 35 C (41 F and 95 F). APPLICATION METHOD Apply with a short nap roller or a brush. Part B has to be blended with the Part A for 2 to 3 minutes until homogeneity is obtained. TEMPERATURE Application temperature: Above 10 C (50 F). The mixture can be used for 15 to 20 minutes at 25 C (77 F). TESTS AND APPROVALS Additional Expertise Fountains Ponds EPOXY Product Code Colour ALSAN TRAFIK EP Amber For further information, visit the product page on our website. TRAFIK EP

145 ALSAN RS 276 PRIMER Additional Expertise Fountains Ponds PMMA ALSAN RS 276 PRIMER is a fast-curing, translucent, two-component primer formulated from polymethyl methacrylate (PMMA) resins. It is used to increase the adhesion of the ALSAN RS system in both indoor and outdoor applications. BENEFITS Sealing and protection against water Quick setting to meet tight deadlines No joints Application at temperatures as low as 3 C Thickness Coverage rate mm wet (15-20 mil wet) 25 m 2 (269 ft 2 ) per container APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. The resin must be evenly distributed over the surface. TEMPERATURE Application temperature: Above 3 C (37 F). Container The ALSAN RS 276 PRIMER resin is offered in a 10 kg (22 lb) resealable container with a locking ring. TESTS AND APPROVALS Units per skid 60 Service life / storage 24 months when properly stored in the original sealed container. SOPREMA INC. Product Code ALSAN RS 276 PRIMER * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. ALSAN RS COMPLEMENTARY PRODUCT ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. For further information, visit the product page on our website.

146 ALSAN RS 230 FIELD ALSAN RS 230 FIELD is a two-component liquid membrane composed of polymethyl methacrylate (PMMA). ALSAN RS 230 FIELD is combined with a textile reinforcement to form a reinforced, monolithic, self-adhesive membrane designed for waterproofing new surfaces or surfaces under repair, whether for indoor or outdoor applications. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines Flexible No joints Application at minimal temperatures as low as 15 C for summer grade, and -5 C for winter grade Polyester reinforced Total minimum consumption Consumption of the base coat Consumption of the finish coat Total minimum coverage rate Thickness Coverage rate mm wet (72-86 mil wet) mm wet (56-60 mil wet) mm wet (22-26 mil wet) 3.0 kg/m 2 (0.28 kg/ft 2 ), approximately 8 m 2 (90 ft 2 ) per container APPLICATION METHOD After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers, brushes or a SOPREMA notched squeegee. The resin must be evenly distributed over the surface. TEMPERATURE Summer grade: The ALSAN RS 230 FIELD membrane can be applied at a substrate temperature between 15 C (59 F) and 50 C (122 F), and an ambient temperature between 15 C (59 F) and 40 C (104 F). Winter grade: The ALSAN RS 230 FIELD membrane can be applied at a substrate temperature between -5 C (23 F) and 20 C (68 F), and an ambient temperature between -5 C (23 F) and 20 C (68 F). Additional Expertise Fountains Ponds PMMA Coverage rate of the base coat 2.0 kg/m 2 (0.19 kg/ft 2 ) Coverage rate of the finish coat 1.0 kg/m 2 (0.09 kg/ft 2 ) TESTS AND APPROVALS Container The ALSAN RS 230 FIELD resin is offered in a 25 kg (55 lb) resealable container with a locking ring. Units per skid 24 Service life / storage 12 months when properly stored in the original sealed container. Product Code Grade Colour SOPREMA INC. For further information, visit the product page on our website. ALSAN RS ALSAN RS 230 FIELD Summer grade Pebble Grey Summer grade Traffic White Winter grade Pebble Grey Winter grade Traffic White * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. * The thickness of the polyester reinforcement is not taken into account in the thickness; the measure is only for the liquid resin. COMPLEMENTARY PRODUCTS ALSAN RS FLEECE is used to improve the resistance of resins to tearing and puncture. ALSAN RS DETAILER is used as a waterproof paste in locations where it is difficult to install a liquid membrane system with reinforcement. ALSAN RS PASTE is used as a mastic for sealing cracks, depressions and gaps before installing liquid membranes. ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application.

147 ALSAN RS 230 FLASH Additional Expertise Fountains Ponds PMMA ALSAN RS FLASH is a two-component liquid membrane composed of polymethyl methacrylate (PMMA). It is combined with a textile reinforcement to form a reinforced, monolithic, self-flashing membrane designed for waterproofing elevations and details in both indoor and outdoor applications. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines Flexible No joints Application at minimal temperature as low as 15 C for summer grade, and -5 C for winter grade Polyester reinforced Total minimum consumption Consumption of the base coat Consumption of the finish coat Thickness Coverage rate mm wet (72-86 mil wet) mm wet (56-60 mil wet) mm wet (22-26 mil wet) APPLICATION METHOD After mixing, apply the resin on the clean substrate, prepared for the intended purpose, using brushes or rollers. The resin must be evenly distributed over the surface. TEMPERATURE Summer grade: ALSAN RS 230 FLASH membrane can be applied at a substrate temperature between 15 C (59 F) and 50 C (122 F), and an ambient temperature between 15 C (59 F) and 35 C (95 F). Winter grade: ALSAN RS 230 FLASH membrane can be applied at a substrate temperature between -5 C (23 F) and 20 C (68 F), and an ambient temperature between -5 C (23 F) and 20 C (68 F). Total minimum coverage rate 3.0 kg/m 2 (0.28 kg/ft 2 ), approximately 4 m 2 (43 ft 2 ) per container Coverage rate of the base coat 2.0 kg/m 2 (0.19 kg/ft 2 ) TESTS AND APPROVALS Coverage rate of the finish coat 1.0 kg/m 2 (0.09 kg/ft 2 ) Container The ALSAN RS 230 FLASH resin is offered in a 12 kg (26 lb) resealable container with a locking ring. SOPREMA INC. ALSAN RS Units per skid 60 Service life / storage 12 months when properly stored in the original sealed container. For further information, visit the product page on our website. PRODUCT Code Grade Colour Summer grade Pebble Grey ALSAN RS 230 FLASH Summer grade Traffic White Winter grade Pebble Grey Winter grade Traffic White * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. * The thickness of the polyester reinforcement is not taken into account in the thickness; the measure is only for the liquid resin. COMPLEMENTARY PRODUCTS ALSAN RS FLEECE is used to improve the resistance of resins to tearing and puncture. ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application.

148 ALSAN RS 260 LO FIELD ALSAN RS 260 LO FIELD is a two-component liquid membrane composed of polymethacrylate (PMA). It combines a resin and textile reinforcement to form a reinforced, monolithic, self-adhesive membrane used for waterproofing new surfaces or surfaces under repair, whether for indoor or outdoor applications. Special low-odour formulation improves working conditions and provides considerably less production down time due to odour related to health and environmental hazards. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C Polyester reinforced APPLICATION METHOD After mixing, apply the resin on the clean substrate, prepared for the intended purpose, using brushes or rollers. The resin must be evenly distributed over the surface. TEMPERATURE Application temperature: Above 3 C (37 F). Additional Expertise Fountains Ponds PMA Total minimum consumption Consumption of the base coat Consumption of the finish coat Total minimum coverage rate Thickness Coverage rate mm wet (72-86 mil wet) mm wet (56-60 mil wet) mm wet (22-26 mil wet) 3.0 kg/m 2 (0.28 kg/ft 2 ), approximately 8 m 2 (90 ft 2 ) per container Coverage rate of the base coat 2.0 kg/m 2 (0.19 kg/ft 2 ) Coverage rate of the finish coat 1.0 kg/m 2 (0.09 kg/ft 2 ) Container The ALSAN RS 260 LO FIELD resin is offered in a 25 kg (55 lb) resealable container with a locking ring. Units per skid 24 Service life / storage 12 months when properly stored in the original sealed container. TESTS AND APPROVALS SOPREMA INC. For further information, visit the product page on our website. ALSAN RS Product Code Colour ALSAN RS 260 LO FIELD Pebble Grey Traffic White * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. * The thickness of the polyester reinforcement is not taken into account in the thickness; the measure is only for the liquid resin. COMPLEMENTARY PRODUCTS ALSAN RS FLEECE is used to improve the resistance of resins to tearing and puncture. ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS DETAILER is used as a waterproof paste in locations where it is difficult to install a liquid membrane system with reinforcement. ALSAN RS PASTE is used as a mastic for sealing cracks, depressions and gaps before installing liquid membranes.

149 ALSAN RS 260 LO FLASH Additional Expertise Fountains Ponds PMA ALSAN RS 260 LO FLASH is a two-component liquid membrane composed of polymethacrylate (PMA). It combines a resin and textile reinforcement to form a reinforced, monolithic, self-adhesive membrane used for waterproofing elevations and details in both indoor and outdoor applications. Special low-odour formulation improves working conditions and provides considerably less production down time due to odour related to health and environmental hazards. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines Flexible No joints Application at temperatures as low as 3 C APPLICATION After mixing, apply the resin on the clean substrate prepared for the intended purpose, using brushes or rollers. The resin must be evenly distributed over the surface. Polyester reinforced TEMPERATURE Application temperature: Above 3 C (37 F). Thickness TESTS AND APPROVALS Total minimum consumption Consumption of the base coat Consumption of the finish coat mm wet (72-86 mil wet) mm wet (56-60 mil wet) mm wet (22-26 mil wet) SOPREMA INC. Coverage rate Total minimum coverage rate 3.0 kg/m 2 (0.28 kg/ft 2 ), approximately 4 m 2 (43 ft 2 ) per container ALSAN RS Coverage rate of the base coat 2.0 kg/m 2 (0.19 kg/ft 2 ) Coverage rate of the finish coat 1.0 kg/m 2 (0.09 kg/ft 2 ) Container The ALSAN RS 260 LO FLASH resin is offered in a 12 kg (26 lb) resealable container with a locking ring. Units per skid 60 For further information, visit the product page on our website. Service life / storage 12 months when properly stored in the original sealed container. Product Code Colour ALSAN RS 260 LO FLASH Pebble Grey Traffic White * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. * The thickness of the polyester reinforcement is not taken into account in the thickness; the measure is only for the liquid resin. COMPLEMENTARY PRODUCTS ALSAN RS FLEECE is used to improve the resistance of resins to tearing and puncture. ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application.

150 ALSAN RS 287 COLOR FINISH BASE ALSAN RS 287 COLOR FINISH BASE is a colourless two-component resin made from polymethyl methacrylate (PMMA) in which an ALSAN RS COLOR ADDITIVE coloured paste is added. BENEFITS Waterproofing and protection against water and de-icing salt Quick setting to meet tight deadlines No joints Application at temperatures as low as 3 C Thickness APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. TEMPERATURE Application temperature: Above 3 C (37 F). Additional Expertise Fountains Ponds PMMA on a rough surface on a smooth surface mm wet (20-25 mil wet) mm wet (12-15 mil wet) Coverage rate on a rough surface 0.5 kg/m 2 (0.046 kg/ft 2 ) on a smooth surface 0.3 kg/m 2 (0.028 kg/ft 2 ) Container The ALSAN RS 287 COLOR FINISH BASE resin is offered in an 8.5 kg (18.7 lb) resealable container with a locking ring. Units per skid 40 Service life / storage 12 months when properly stored in the original sealed container. Product Code Colour ALSAN RS 287 COLOR FINISH BASE Colourless * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. For further information, visit the product page on our website. ALSAN RS COMPLEMENTARY PRODUCTS ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS COLOR ADDITIVE is a coloured paste intended to be added to liquid PMMA resins. ALSAN RS DECO CHIPS polymer flakes are used as decorative elements. COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements.

151 ALSAN RS 281 CLEAR FINISH Additional Expertise Fountains Ponds PMMA ALSAN RS 281 CLEAR FINISH is a colourless finishing resin made from polymethyl methacrylate (PMMA). It is used as a protective coating when COLORED QUARTZ AGGREGATES or DECO CHIPS are applied. Thickness on rough surfaces Coverage rate on rough surfaces Containers mm wet (20-25 mils wet) 20 m 2 (215 ft 2 ) per container The ALSAN RS 281 CLEAR FINISH resin is offered in a 10 kg (22 lb) resealable container. Units per skid 60 Service life / storage 12 months when properly stored in the original sealed container. APPLICATION METHOD Apply with a roller. After mixing, apply the resin on the clean substrate prepared for the intended purpose, using rollers or brushes. TEMPERATURE Application temperature: Above 3 C (37 F). Product Code Colour ALSAN RS 281 CLEAR FINISH Clear TESTS AND APPROVALS * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. SOPREMA INC. COMPLEMENTARY PRODUCT ALSAN RS CATALYST POWDER is a reactive agent used to induce curing during membrane application. ALSAN RS DECO CHIPS polymer flakes are used as decorative elements. COLORED QUARTZ AGGREGATES and NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection and as decorative elements. ALSAN RS For further information, visit the product page on our website.

152 Typical Details

153 FOUNTAIN Copyrght 2014 SOPREMA Title Drawing Number Scale Fountain BGW23 N.T.S.

154

155 COMPLEMENTS COMPLEMENTS

156 ALSAN FLASHING ALSAN FLASHING is a patented single component resin composed of a mix of polyurethane and bitumen. Applied in liquid form and used with FLASHING REINFORCEMENT, the product becomes a flashing or an exterior waterproofing membrane, and is ideal for use on upstands and other details where it is difficult to apply waterproofing membranes sheets. BENEFITS Superior protection against moisture Less expensive than other systems Fire hazards are eliminated because no torch is used, bringing peace of mind to customers, neighbours and tenants Colour Coverage rate Cleaning Storage / service life Brown 14 m 2 (150 ft 2 ) per container Clean with petroleum solvents, such as mineral spirits, Varsol, and xylene. Up to 9 months in original sealed containers protected from humidity. Keep away from flames or sparks. Product Code Volume APPLICATION METHOD Applied using a brush or roller For further information, visit the product page on our website. Accessories Complementary Products ALSAN FLASHING L (1 US gal) L (5 US gal) FLASHING REINFORCEMENT FLASHING REINFORCEMENT is 100% polyester stitch-bonded fabric. This high performance reinforcement is made without the use of a chemical binder. It is used in conjunction with ALSAN FLASHING. Its high absorption capability allows to quickly wet into and become encapsulated by ALSAN FLASHING liquid membrane. Thickness Dimensions Roll weight Storage and handling Product 0.6 mm (25 mil) 0.15 x 30.5 m (6 in x 100 ft) 100 g/m² (0.02 lb/ft²) Always store in a cool, dry place. Store flat to avoid deforming rolls and creasing the fabric. Code APPLICATION METHOD While applying gentle pressure, roll the reinforcement using a medium nap roller soaked with resin in order to remove air bubbles, wrinkles, etc. Apply an additional liquid resin mixture on the reinforcement until it is completely saturated and continue to work the resin. FLASHING REINFORCEMENT For further information, visit the product page on our website.

157 ALSAN RS CATALYST POWDER Accessories Complementary Products ALSAN RS CATALYST POWDER is a dibenzoyl peroxide-based reactive agent used to induce curing of all ALSAN RS resins during membrane application. ALSAN RS CATALYST POWDER is a white powder. Container ALSAN RS CATALYST POWDER is offered in pre-packaged bags of 0.1 kg (0.22 lb). Packages per box 50 Storage / service life 12 months when properly stored in the original sealed container. Product Code Colour ALSAN RS CATALYST POWDER White APPLICATION METHOD Add the catalyst only to the amount of material that will be used within the next 10 to 15 minutes. Add the premeasured catalyst powder to the resin, stir for two minutes, and apply on the substrate. TEMPERATURE Do not store in direct sunlight or at temperatures below 0 C (32 F) or over 25 C (77 F). For further information, visit the product page on our website. ALSAN RS CLEANER ALSAN RS CLEANER is a clear, blended solvent used to clean and reactivate the transition area of in-place SOPREMA ALSAN RS at tie-ins, on repairs and between staged coating of resins. ALSAN RS CLEANER is also used to clean and prepare plastic and metal surfaces prior to application of ALSAN RS membrane and may also be used as a solvent for cleaning spills, tools and equipment. Container Storage Product 18,9 L Always store closed container in cool, ventilated and dry location, away from fire hazard may be acute. Code APPLICATION METHOD Apply ALSAN RS CLEANER using clean rags or cloth. After the ALSAN RS CLEANER has been allowed 15 minutes to evaporate, the surface may be coated as required. ALSAN RS CLEANER For further information, visit the product page on our website.

158 ALSAN RS COLOR ADDITIVES ALSAN RS COLOR ADDITIVE is a coloured paste intended to be added to a liquid polymethyl methacrylate (PMMA) resin. Container The ALSAN RS COLOR ADDITIVE is offered in a 1.5 kg (3.3 lb) container. Units per skid 160 Storage / service life 12 months when properly stored in the original sealed container. Product Code Colour ALSAN RS COLOR ADDITIVE * Other colours available upon request Traffic White Light Grey Pebble Grey Window Grey Stone Grey Beige Terracotta APPLICATION METHOD The ALSAN RS COLOR vadditive coloured paste must be evenly mixed before being added to the resin. After mixing, apply the resin on the clean substrate, prepared for the intended purpose, using rollers, brushes or a notched scraper. For further information, visit the product page on our website. Accessories Complementary Products ALSAN RS DECO CHIPS The thin, angular ALSAN RS DECO CHIPS polymer flakes are used as decorative elements with ALSAN RS liquid membranes. Flakes dimension Packaging Storage and handling Approximately 3.2 mm (1/8 in). ALSAN RS DECO CHIPS decorative flakes are provided in a 22.5 kg (50 lb) resealable package. Always store in a clean, dry place. The product packaging must not have been opened before use. Product Code Colour ALSAN RS DECO CHIPS Black Marble Sparkle 1/8 in Light Grey White 1/8 in Prairie Blend 1/8 in Light Grey White 1/16 in Harley Chrome 1/16 in Prairies Blend 1/16 in APPLICATION METHOD ALSAN RS DECO CHIPS must be spread randomly during an ALSAN RS resin wet application, saturating the target surface. They can also be spread using a mechanical applicator. Once the ALSAN RS resin is cured, excess ALSAN RS DECO CHIPS can be removed using a vacuum cleaner or an oil-free air compressor. Use a fine sandpaper to smooth the surface, and saturate with a finish coat of ALSAN RS 281. For further information, visit the product page on our website.

159 ALSAN RS DETAILER Accessories Complementary Products ALSAN RS DETAILER is a mixture of two-component liquid resin made from polymethyl methacrylate (PMMA) and microfibres used as a waterproof paste in locations where it is difficult to install a liquid membrane system with reinforcement. Coverage rate on smooth surfaces Container 3.0 kg/m 2 (0.28 kg/ft 2 ) The ALSAN RS DETAILER resin is offered in a 12 kg (26 lb)resealable container with a locking ring. Units per skid 125 Storage / service life 12 months when properly stored in the original sealed container. Product Code Colour APPLICATION METHOD After mixing, apply the resin to the clean substrate, prepared for the intended purpose, using a trowel or a brush. ALSAN RS DETAILER Pebble Grey * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. For further information, visit the product page on our website. ALSAN RS FLEECE ALSAN RS FLEECE is used to improve the resistance of resins to tearing and puncture. It also increases the resistance to flexural fatigue and expands the sealing capacity, while maintaining the uniformity of the membrane. Thickness mm (30-40 mil) Roll weight 100 g/m 2 (0.02 lb/ft 2 ) Storage and handling Always store in a cool, dry place. Store flat to avoid deforming rolls and creasing the fabric. Product Code Dimensions ALSAN RS FLEECE m x 105 cm (164 ft x 41.3 in) 50 m x 53 cm (164 ft x 20.7 in) 50 m x 35 cm (164 ft x 13.8 in) 50 m x 26 cm (164 ft x 10.3 in) 50 m x 10 cm (164 ft x 4 in) APPLICATION METHOD Unroll the polyester reinforcement on the liquid resin, making sure the SMOOTH SIDE IS FACING UP (natural unfolding procedure). While applying gentle pressure, roll the reinforcement using a medium nap roller soaked with resin in order to remove air bubbles, wrinkles, etc. Apply an additional liquid resin mixture on the reinforcement until it is completely saturated and continue to work the resin. For further information, visit the product page on our website.

160 ALSAN RS PASTE ALSAN RS PASTE is a mixture of two-component liquid resin made from polymethyl methacrylate (PMMA). ALSAN RS PASTE is used as a mastic for sealing cracks, depressions and gaps before installing ALSAN RS liquid membranes. It is also used to level joints between applications of ALSAN RS FLEECE. Coverage rate 2.0 kg/m 2 (0.19 kg/ft 2 ) Container The ALSAN RS PASTE resin is offered in a 15 kg (33 lb) resealable container with a locking ring. Units per skid 40 Storage / service life 12 months when properly stored in the original sealed container. Product Code Colour APPLICATION METHOD After mixing, apply the resin to the clean substrate, prepared for the intended purpose, using notched squeegees, rollers or brushes. Accessories Complementary Products ALSAN RS PASTE Pebble Grey * Coverage rate may vary depending on the substrate condition. * Wet and dry thicknesses are always equivalent. For further information, visit the product page on our website. COLOR QUARTZ AGGREGATES The COLORED QUARTZ AGGREGATES are used as slip-resistant surface coating or protection, and as decorative elements when applying liquid ALSAN RS membranes. Dimensions Sizes Nos. 00, 0, 1, and 2 Packaging Storage and handling The COLORED QUARTZ AGGREGATES are packed in a 23 kg (50 lb) bag, except for size N o 2, which is offered in 45 kg (100 lb) bags. Always store in a clean, dry place. The product packaging must not have been opened before use. Product Code Colour Tobacco Tan APPLICATION METHOD COLORED QUARTZ AGGREGATES must be spread randomly during an ALSAN RS liquid resin wet application. Once the ALSAN RS resin is cured, excess COLORED QUARTZ AGGREGATES can be removed using a vacuum cleaner, a push brush or an oil-free air compressor. Saturate with a finish coat of ALSAN RS 281. COLORED QUARTZ AGGREGATES Granite Grey Smoke * Other colours available upon request. For further information, visit the product page on our website.

161 NATURAL QUARTZ AGGREGATES Accessories Complementary Products The NATURAL QUARTZ AGGREGATES are used as slip-resistant surface coating or protection when applying liquid ALSAN RS membranes. Colour Packaging Storage and handling Natural quartz The NATURAL QUARTZ AGGREGATES are packed in a 23 kg (50 lb) bag, except for size N o 2, which is offered in 45 kg (100 lb) bags. Always store in a clean, dry place. The product packaging must not have been opened before use. Product Code Sizes NATURAL QUARTZ AGGREGATES APPLICATION METHOD NATURAL QUARTZ AGGREGATES must be spread randomly during an ALSAN RS liquid resin wet application. Once the ALSAN RS resin is cured, excess NATURAL QUARTZ AGGREGATES can be removed using a vacuum cleaner, a push brush or an oil-free air compressor. Saturate with a finish coat of ALSAN RS 287 COLOR BASE. For further information, visit the product page on our website. ALSAN TRAFIK HP ACCELERATOR ALSAN TRAFIK HP ACCELERATOR is added to ALSAN TRAFIK HP 520 to accelerate the drying time of the liquid waterproofing membrane. ALSAN TRAFIK HP ACCELERATOR is used exclusively with ALSAN TRAFIK HP 520 and should not be combined with any other ALSAN product. Container 100 ml* Units per skid 36 Storage / service life Up to 12 months in original sealed containers. Containers must be stored away from heat, moisture, sunlight and strong oxidizing products. APPLICATION METHOD Premix and completely pour the container of ALSAN TRAFIK HP ACCELERATOR in a container of ALSAN TRAFIK HP 520. Mix well for at least 1 minute using a mixer at low speed (300 to 450 RPM). Product Code Colour ALSAN TRAFIK HP ACCELERATOR Clear Yellow * Only one ALSAN TRAFIK HP ACCELERATOR container is needed per ALSAN TRAFIK HP 520 container. For further information, visit the product page on our website.

162 ALSAN TRAFIK HP COLORANT ALSAN TRAFIK HP COLORANT is a pigment paste. When added to ALSAN TRAFIK HP 540 (clear), it increases its opacity and widens the possibilities of the ALSAN TRAFIK HP 500 system when it comes to its final colour. When added to the ALSAN TRAFIK HP 540 (clear), the ALSAN TRAFIK HP COLORANT can also be used to draw lines and delimit certain areas. Container 1 kg (2.2 lb) Units per skid 729 Storage / service life Up to 24 months in original sealed containers. Containers must be stored away from heat, flame, moisture and sunlight. Product Code Colour ALSAN TRAFIK HP COLORANT Grey Dark Grey Beige* Pebble Grey Trafik White** Trafik Yellow* Trafik Blue Black Trafik Red* ANTIROCK EMULSION PRIMER APPLICATION METHOD Premix and completely pour the container of ALSAN TRAFIK HP COLORANT in a container of ALSAN TRAFIK HP 540. Mix well for at least 1 minute using a mixer at low speed (300 to 450 RPM) and a Jiffy mixing paddle to ensure colour uniformity. For further information, visit the product page on our website. * For Beige, Trafik Yellow and Trafik Red*, 2 containers of ALSAN TRAFIK HP COLORANT are needed for each container of ALSAN TRAFIK HP 540 (clear). ** For Trafik white, 1.5 containers of ALSAN TRAFIK HP COLORANT are needed for each container of ALSAN TRAFIK HP 540 (clear). Accessories Complementary Products ANTIROCK EMULSION PRIMER is a bitumen emulsion that is a stabilized solvent-free mixture of bitumen and water. This product is designed to prepare the concrete or metal surfaces of civil engineering structures to allow proper adhesion of the waterproofing membranes of the TRAFIKROCK series. BENEFIT Improves the adhesion of ANTIROCK heat-welded waterproofing membranes. APPLICATION METHOD Applied using a brush, a roller or a spray Container 19 L (5 US gal) Coverage rate From 0.15 to 0.25 L/m 2 Units per skid 36 Cleaning Storage / service life Tools can be cleaned with solvents such, as mineral spirits, Varsol, and xylene. Up to 12 months in original, sealed containers. Storage temperature: From 0 to 40 C (from 32 to 104 F). KEEP AWAY FROM FROST. Product Code Colour ANTIROCK EMULSION PRIMER Dark Brown For further information, visit the product page on our website.

163 ANTIROCK PRIMER Accessories Complementary Products ANTIROCK PRIMER is a mixture of SBS modified bitumen, volatile solvents and adhesionenhancing additives. It is used as a primer on concrete or metal surfaces of engineering works to improve the adhesion of heat-welded TRAFIKROCK and ANTIROCK waterproofing membranes. BENEFITS Improves the adhesion of TRAFIKROCK and ANTIROCK heatwelded waterproofing membranes Can be applied at any temperature Colour Black Coverage rate From 0.15 à 0.25 L/m 2 Storage / service life Up to 5 months in original sealed containers. APPLICATION METHOD Applied using a brush, a roller or a spray Product Code Container Units per skid L (5 US gal) 36 ANTIROCK PRIMER L (50 US gal) 4 For further information, visit the product page on our website. COLPHENE BSW PROTECT R The COLPHENE BSW PROTECT R pre-applied membrane is used as a protective membrane over the COLPHENE BSW H membrane prior to placement of the reinforcement steel bars and pouring of the concrete slab. It is one of SOPREMA solutions designed for projects located in high-density urban areas. BENEFITS Protects the COLPHENE BSW H membrane from damage caused by foot traffic APPLICATION METHOD Self-adhesive Surface Sand Underface Release protective film Reinforcement Composite Bitumen SBS modified Thickness 2.0 mm (80 mil) Dimensions 15 x 1 m (49.5 x 3.3 ft) Net area 15 m 2 (161.5 ft 2 ) Roll weight 36.0 kg (78.0 lb) Rolls per skid 30 Product Code For further information, visit the product page on our website. COLPHENE BSW PROTECT R 00277

164 ELASTOCOL 350 ELASTOCOL 350 is a water-based stabilized bituminous emulsion. It is used to enhance the adhesion properties of heat-weldable and self-adhesive waterproofing membranes on most surfaces. This primer can be used in areas where solvent-based primers are not recommended. BENEFITS Cold application Single component, ready-to-use Volume Coverage rate Cleaning Storage / service life 19 L (5 US gal) From 0.15 to 0.25 L/m 2 (from 0.37 to 0.61 US gal/100 ft 2 ) Tools can be cleaned with solvents, such as mineral spirits, Varsol, and xylene. Up to 24 months in original sealed containers. Storage temperature: From 5 to 40 C (from 41 to 104 F). Do not expose to freezing. Product Code Colour APPLICATION METHOD Applied using a brush, roller or spray gun TESTS AND APPROVALS For further information, visit the product page on our website. Accessories Complementary Products ELASTOCOL Dark Brown ELASTOCOL 500 ELASTOCOL 500 is a primer made from bitumen, fast-evaporating solvents and adhesiveenhancing additives. It is used on concrete and metal surfaces in order to enhance the adhesion of heat-welded waterproofing membranes. BENEFITS Cold application Single component, ready-to-use APPLICATION METHOD Applied with a brush, roller, spray gun or spray can TESTS AND APPROVALS Colour Coverage rate Cleaning Storage / service life Black From 0.15 to 0.25 L/m 2 (from 0.37 to 0.61 US gal/100 ft 2 ) Tools can be cleaned with solvents such as mineral spirits, Varsol, and xylene. Up to 60 months in original sealed containers. Store away from direct sunlight and open flame. listed by Product Code Volume Units per skid ELASTOCOL L (5 US gal) L (50 US gal) g spray can 1020 For further information, visit the product page on our website.

165 ELASTOCOL STICK Accessories Complementary Products ELASTOCOL STICK is a primer designed to enhance the adhesion of self-adhesive membranes on porous surfaces. It is composed of SBS synthetic rubbers, adhesion-enhancing resins and volatile solvents. It is used as a primer on surfaces, such as concrete, metal, and wood. BENEFITS Cold application Single component, ready-to-use Colour Coverage rate Cleaning Storage / service life Red Porous substrates: from 0.3 to 0.5 L/m 2 (from 0.74 to 1.23 US gal/100 ft 2 ) Non-porous substrates: from 0.1 to 0.25 L/m 2 (from 0.24 to 0.61 US gal/100 ft 2 ) Tools can be cleaned with solvents such as mineral spirits, Varsol, and xylene. Up to 24 months in original sealed containers. Store in a well-ventilated area. Keep away from heat, humidity, oxidizing agents and direct sunlight. Storage temperature: from 5 to 40 C (from 41 to 104 F). Do not expose to freezing. Product Code Volume Units per skid APPLICATION METHOD Applied using a brush, roller or spray can TESTS AND APPROVALS For further information, visit the product page on our website. listed by ELASTOCOL STICK L (1 US gal) L (5 US gal) g spray can 984 ELASTOCOL STICK H 2 0 ELASTOCOL STICK H 2 O is a polymer emulsion-based primer designed to improve the adhesion of self-adhesive waterproofing membranes on most substrates. It is an excellent choice when the use of solvent-based primer is not recommended. BENEFITS Cold application Single component, ready-to-use APPLICATION METHOD Applied using a brush, roller or spray gun TESTS AND APPROVALS Volume Coverage rate Cleaning Storage / service life 19 L (5 US gal) From 0.1 to 0.3 L/m 2 (from 0.24 to 0.74 US gal/100 ft 2 ) Clean wet tools with water. When dry, clean with petroleum solvents such as mineral spirits, Varsol, and xylene. Keep from freezing. Up to 24 months in original sealed containers. Product Code Colour ELASTOCOL STICK H 2 O Blue For further information, visit the product page on our website.

166 ELASTOCOL STICK ZERO ELASTOCOL STICK ZERO is a primer compliant with LEED requirements (IEQ Credit 4.1). It is designed to enhance the adhesion of self-adhesive membranes on most substrates including porous surfaces, such as gypsum boards, at temperatures above -10 C (14 F). It is composed of synthetic polymers, adhesion-enhancing resins and volatile solvents. BENEFITS Cold application Single component, ready-to-use Volume Coverage rate Cleaning Storage / service life 19 L (5 US gal) Porous substrates: from 0.2 to 0.4 L/m 2 (from 0.49 to 0.98 US gal/100 ft 2 ) Non-porous substrates: from 0.1 to 0.25 L/m 2 (from 0.24 to 0.61 US gal/100 ft 2 ) Tools can be cleaned with petroleum solvents, such as mineral spirits, Varsol, and xylene. Up to 60 months in original sealed containers. Store away from direct sunlight and open flame. Keep away from frost. APPLICATION METHOD Applied using a brush or roller TESTS AND APPROVALS For further information, visit the product page on our website. listed by Accessories Complementary Products Product Code Colour ELASTOCOL STICK ZERO Red SOPRADRAIN 10-G SOPRADRAIN 10-G is a high-density drainage board composed of a polypropylene core on which a geotextile is factory laminated. The board is installed on membranes for drainage in numerous waterproof applications, on below-grade walls and on SOPRANATURE green roofs and vegetable roof gardens. BENEFITS Light load on structures Reduced thickness compared to a drainage layer of gravel Excellent resistance to most chemicals APPLICATION METHOD Loose laid or fastened vertically Composition Thickness Dimensions Non-woven geotextile laminated on a polypropylene core 10 mm (0.4 in) 1.83 x m (6 x 50 ft) Area 27.9 m 2 (300 ft 2 ) Weight Resistance to compression Product 25.0 kg (55.0 lb) 550 kpa (11,000 psf) Code SOPRADRAIN 10-G For further information, visit the product page on our website.

167 SOPRADRAIN 15-G Accessories Complementary Products SOPRADRAIN 15-G is a high-density drainage board composed of a polypropylene core on which a geotextile is factory laminated. The board is installed on waterproofing membranes in commercial applications with vertical or horizontal drainage. BENEFITS Light load on structures Reduced thickness compared to a drainage layer of gravel Excellent resistance to most chemicals Composition Thickness Non-woven geotextile laminated on a polypropylene core 10 mm (0.4 in) Weight 1 kg/m 2 (0.1 kg/in 2 ) Resistance to compression 718 kpa (15,000 psf) APPLICATION METHOD Temporarily held in place until backfilling Product Code Dimensions SOPRADRAIN 15-G x m (4 x 50 ft) x m (6 x 50 ft) For further information, visit the product page on our website. SOPRADRAIN 18-G SOPRADRAIN 18-G is a high-density drainage board composed of a polypropylene core and a highly-resistant woven polypropylene filter, offering optimal performance under concrete and soils in areas under high loads, such as plaza decks and parking areas. BENEFITS Light load on structures Reduced thickness compared to a drainage layer of gravel Excellent resistance to most chemicals Highly-resistant filter allowing the concrete to be poured directly onto its surface APPLICATION METHOD Must be temporarily held in place until covering TESTS AND APPROVALS Composition Thickness Dimensions Non-woven geotextile laminated on a polypropylene core 10 mm (0.4 in) 1.83 x m (6 x 50 ft) Gross area 27.9 m 2 (300 ft 2 ) Weight 1 kg/m 2 (0.1 kg/in 2 ) Resistance to compression Product 862 kpa (18,000 psf) Code For further information, visit the product page on our website. SOPRADRAIN 18-G 20526

168 SOPRADRAIN ECO-VENT SOPRADRAIN ECO-VENT is a high-density drainage board composed of a post-industrial recycled polypropylene core on which a geotextile is factory-laminated. Tangled polypropylene filaments are melted and molded into an embossed board following a crimped pattern, ensuring good flexibility. BENEFITS Excellent durability Reduces installation costs (long roll decreasing the amount of overlaps) Composition Dimensions Area Roll weight Geotextile laminated on a post-industrial recycled polypropylene core 0.99 x 30.5 m (3.25 x 100 ft) 30.1 m 2 (324 ft²) 25.5 kg (56.0 lb) APPLICATION METHOD Loosely laid TESTS AND APPROVALS Accessories Complementary Products Product Code SOPRADRAIN ECO-VENT For further information, visit the product page on our website. SOPRADRAIN ECO-2 SOPRADRAIN ECO-2 is one of a new generation of environmentally conscious SOPREMA products. This drainage composite consists of a post-industrial recycled polypropylene drainage core of fused, entangled filaments and a geocomposite fabric bonded to each side. The entangled filaments are moulded into a square waffle pattern that maintains the flexible design. BENEFITS Excellent durability Second fabric eliminates needs for protection board Recycled content polymer contributes towards LEED points such as MR 4.1 and MR 4.2 APPLICATION METHOD Loosely laid TESTS AND APPROVALS Composition Dimensions Area Roll weight Product Drainage panel made of recycled polypropylene onto which a geo-textile factory laminated on each side 0.99 x 30.5 m (3.25 x 100 ft) 30.1 m² (324 ft²) 29 kg (64 lb) Code SOPRADRAIN ECO For further information, visit the product page on our website.

169 SOPRAGRIP F Accessories Complementary Products SOPRAGRIP F is a self-adhesive membrane composed of SBS modified bitumen and an exposed non-woven polyester reinforcement. This membrane can be used as a cover strip on the top termination of COLPHENE ICF membranes. It is also used as a reinforcing strip on gypsum or concrete board joints. The non-woven polyester surface provides good adhesion properties for the installation of liquid air and vapour barriers and exterior finishing coatings. BENEFIT Excellent adhesion Surface Underface Bitumen Thickness Non-woven polyester reinforcement Silicone release film SBS modified 1.2 mm (47 mil) APPLICATION METHOD The membrane can be installed directly on polystyrene surfaces. Other substrates, such as gypsum or concrete boards must first be coated with the ELASTOCOL STICK, ELASTOCOL STICK ZERO or ELASTOCOL STICK H 2 O primer. SOPRAGRIP F is installed without overlapping edges. Weight 0.8 kg/m 2 Product Code Dimensions SOPRAGRIP F SOPRAMASTIC x m (39 in x 55 ft) x m (18 in x 55 ft) x m (12 in x 55 ft) x m (10 in x 55 ft) x m (6 in x 55 ft)* x m (4 in x 55 ft) For further information, visit the product page on our website. * Only 6 inches width SOPRAGRIP F is recommended as a cover strip on top termination of the membranes as well as reinforcing strip on vertical panel joints. SOPRAMASTIC is a black mastic composed of SBS modified bitumen, fibres, mineral substances and solvents. It is an ideal complement to bituminous waterproofing membranes as joint filler and caulking material. It is compatible with bitumen-based materials and has excellent waterproofing properties. SOPRAMASTIC is an all-purpose mastic formulated with a high content of polymer to resist flow at high temperature, and designed to be easily applied at temperatures reaching -10 C. BENEFITS Characterized by its excellent adhesion on a wide variety of materials without a primer Can be applied on damp surfaces APPLICATION METHOD Can be applied on damp surfaces. TESTS AND APPROVALS Colour Cleaning Storage / service life Black Tools can be cleaned with solvents such as mineral spirits, Varsol, and xylene. Up to 36 months in original sealed containers protected from humidity. Store in a cool, dry area, away from open flame. Product Code Volume Units per skid ml 1,200 SOPRAMASTIC ml L 60 For further information, visit the product page on our website.

170 SOPRASEAL LM 200 T SOPRASEAL LM 200 T is a water-based single-component liquid product made of synthetic rubbers. SOPRASEAL LM 200 T is used as an air and vapour barrier or as a rigid insulation adhesive. It can be used on most building surfaces, such as masonry, concrete, wood and gypsum, as well as insulation boards. BENEFITS Easy application and fast installation Very flexible film with high percentage of elongation Film thickness Coverage rate Contenant 2.3 mm (90 mil) wet, 1.15 mm (45 mil) dry 2 L/m 2, approximately 10 m 2 (100 ft 2 ) per container 19 L (5 US gal) Units per skid 36 Service life / storage Cleaning Up to 2 years in original sealed containers. KEEP AWAY FROM FROST. Freshly applied adhesive can be cleaned with soapy water. After curing, clean with solvents (mineral spirits, Varsol, and xylene) or using mechanical methods. APPLICATION METHOD Apply SOPRASEAL LM 200 T using a trowel or a brush and leave to dry at a temperature of 5 C or more. Curing time depends on the relative humidity, temperature and air movement. TEMPERATURE Do not use if there is a risk of rain or frost 24 hours after the application. For further information, visit the product page on our website. Accessories Complementary Products Product Code Colour SOPRASEAL LM 200 T Grey

171 SOPRASEAL WFM Accessories Complementary Products SOPRASEAL WFM is a self-adhesive waterproofing membrane composed of SBS modified bitumen and a tri-laminated woven polyethylene facer. The self-adhesive lower face is protected by a plastic release protection film. This product is used as a through-wall membrane, a transition membrane, as well as a waterproofing membrane around openings. BENEFITS Easy-to-use silicone release film Excellent tensile strength, resistance to puncture, abrasion and creep Compatibility with sprayed polyurethane Surface Underface Bitumen Thickness Tri-laminated woven polyethylene Silicone release film SBS modified 1 mm (40 mil) APPLICATION METHOD Self-adhesive For further information, visit the product page on our website. Product Code Dimensions Roll weight SOPRASEAL WFM (45 cm-18 in) x 0.45 m (75 x 1.5 ft) 10.3 kg (22.6 lb) SOPRASEAL WFM (30 cm-12 in) x 0.3 m (75 x 1 ft) 6.9 kg (15.1 lb) SOPRASEAL STICK 1100 T CUT ROLLS SOPRASEAL STICK 1100 T in cut rolls is an air and vapour barrier with a self-adhesive underface. It is used as a through-wall membrane, a masonry flashing, a transition membrane, as well as a waterproofing membrane around openings. SOPRASEAL WFM can also be used in conjunction with SOPRASEAL STICK 1100 T as a wall flashing membrane. BENEFITS Easy-to-use silicone release film Consistent thickness APPLICATION METHOD Self-adhesive TESTS AND APPROVALS Surface Underface Bitumen Thickness Tri-laminated woven polyethylene Silicone release film SBS modified 1.0 mm (40 mil) Product Code Dimensions SOPRASEAL STICK 1100 T IN CUT ROLLS cm x 22.9 m (18 in x 75 ft) cm x 22.9 m (12 in x 75 ft) cm x 22.9 m (9 in x 75 ft) cm x 22.9 m (6 in x 75 ft) cm x 22.9 m (4 in x 75 ft) For further information, visit the product page on our website.

172 SOPRASEAL STICK VP CUT ROLLS SOPRASEAL STICK VP is a self-adhesive vapour-permeable air barrier membrane with a tri-laminated polypropylene complex on its surface. Used in wall construction, it stands out due to its unmatched adhesive properties. It can be used as a through-wall flashing and transition membrane. BENEFITS Better adhesive properties than competitive products UV exposure up to 180 days Self-sealing membrane ensuring continuous waterproofing No fasteners required Surface Underface Thickness Tri-laminated polypropylene complex Self-adhesive, covered with a silicone release film 0.6 mm (24 mil) APPLICATION METHOD Self-adhesive TEMPERATURE Application temperatures: From -7 à 40 C (from 19 à 104 F) Service temperatures: From -40 à 85 C (from -40 à 185 F) Accessories Complementary Products Product Code Dimensions Weight SOPRASEAL STICK VP IN CUT ROLLS cm x 30 m (12 in x 98 ft) 2.7 kg cm x 30 m (9 in x 98 ft) 2.0 kg cm x 30 m (6 in x 98 ft) 1.4 kg For further information, visit the product page on our website. SOPRASOLIN HD SOPRASOLIN HD is a multipurpose self-adhesive waterproofing membrane composed of SBS modified bitumen protected by aluminium foil. SOPRASOLIN HD is designed to waterproof details around penetrations: vents, vent ducts, skylights, chimneys, etc. The use of SOPRASOLIN HD is recommended for repairs and general maintenance works. It is designed to be exposed to the weather. BENEFITS Excellent tear resistance Easy and fast installation APPLICATION METHOD Self-adhesive Thickness Colour Surface Underface Bitumen 1.0 mm (39 mil) Aluminium Aluminium foil Silicone release film SBS modified Product Code Dimensions SOPRASOLIN HD m x 50 cm (33 ft x 20 in) m x 33 cm (33 ft x 13 in) m x 25 cm (33 ft x 10 in) m x 17 cm (33 ft x 6.7 in) m x 10 cm (33 ft x 4.0 in) For further information, visit the product page on our website.

173

174 Equipment and Tools

175 MACADEN The MACADEN is a specialized piece of equipment that allows the automated installation of thermofusible membranes. The MACADEN can be used in summer or winter, at temperatures as low as -10 C. The operation of the MACADEN is fully automated. At first, a hot air blast dries the surface while a burner constantly heats the membrane to liquefy the bitumen. Then, the liquid bitumen fills all of the imperfections of the surface, ensuring the fusion of the waterproofing membrane with the substrate. Finally, a roller applies pressure on the membrane to create a smooth and uniform surface. With the MACADEN, work is quickly completed. Code BENEFITS Uniform installation Faster installation than manual installation Fewer joints Easy installation Reduced labor costs Reduced risks of errors Energy savings Safe Accessories Equipment MINI MACADEN The MINI MACADEN is a machine developed by SOPREMA for installing bitumen membranes. Propelled and self-guided, it ensures the unrolling, welding and smoothing of 8 or 10 m rolls. Its size is suited for transport in a van for greater mobility, and it can lay up to 1,000 m² per day with four people, regardless of the outdoor temperature (> 0 C) or wind conditions. Code (shipping box) BENEFITS Uniform installation Faster installation than manual installation Fewer joints Easy installation Reduced labor costs Reduced risks of errors Energy savings Safe

176 SOPRAMATIC Accessories Equipment and Tools Cart equipped with a hot air blower designed to weld the DUO SELVEDGE of SOPREMA membranes. Code BENEFITS Uniform and constant welding Nozzle adapted to the DUO SELVEDGE dimensions Fast installation Ideal for large surfaces Ideal for projects in which you cannot use a flame Accessories SQUEEGEES AND TROWELS 18-IN NOTCHED SQUEEGEE Code ROUND-NOSED TROWEL Code TROWEL CASE Code 21363

177 TORCHS AND ACCESSORIES HOSE Code : 25 ft : 50 ft ELECTRIC HEAT GUN Code : Heat gun : Nozzle DEGRANULATOR Code Tools Accessories HEAT GUN CUPS Code : No mm : No mm : No mm TURBO HEAT GUN CUP Code EXTENSIONS Code : 100 mm : 200 mm : 420 mm : 500 mm : 600 mm REGULATOR Code TORCH HANDLE Code EXTENSION SUPPORT (RIDGE SUPPORT) Code 26170

178 ROLLERS Accessories Tools 5-IN METAL ROLLER Code IN NEOPHRENE ROLLER Code IN ROLLER Code Accessories 12-IN NEOPHRENE ROLLER 4-IN ROLLER COVER Code Code IN ROLLER HANDLE Code IN ROLLER COVER Code IN ROLLER HANDLE Code 29759

179 OTHERS KNIFE Code SPONGE Code DIGITAL THERMOMETER/HEAT DETECTOR Code Accessories Tools PULLER EXTENDABLE PULLER SOPRASEAL XPRESS G SCREWS Code Code Code ALSAN RS STARTER KIT Code 20808

180 CR /January

181 1.877.MAMMOUTH