Division 11 - Equipment Section 11401
|
|
- Kenneth Thompson
- 6 years ago
- Views:
Transcription
1 PART 1 - GENERAL 1.1 GENERAL A. Division 1 General Requirements applies and becomes a part of this Section of the Specification as fully as if repeated herein. B. Items of equipment which are included in the scope of work of this section are referenced in the Itemized List of Equipment in Section SUMMARY A. Types of work in this section include: PART 2 - PRODUCTS 2.1 MATERIALS 1. Stainless steel countertop- Kitchen island. A. Stainless steel (may be denoted by the abbreviation s.s. or st. st. in this specification) sheet, strip, plate, and flat bar: ASTM-A167-81A, (18-8 Analysis) Type 304, with AISI No. 4 finish for exposed and semi concealed surfaces, unless otherwise specified, 180 grit finish, free of buckets, pits, warps and imperfections. Ensure that direction of grain matches wherever possible on abutting panels. B. Stainless steel tubing: ASTM-A269 type 304, seamless and welded, AISI No. 4 Finish. All tubing to be 16 gauge wall thickness, sizes shown are outside Diameter And face. C. Nuts, bolts, screws, washers and other fastenings: type 304 stainless steel. D. Gauges of material refer to U.S. Standard Gauges. 1. Table tops, counter tops, pot sinks, back splashes 14 gauge s.s. Note: Laminated construction consisting of 16 gauge s.s. on 14 Gauge satin coat may be used only if clearly identified on shop drawings Reviewed by the Consultant. 2. Shelves, utility sinks, angle slides. Bumper guards 16 gauge s.s
2 3. Cabinet bodies 20 gauge s.s. 4. Interior shelves, kick plates 18 gauge s.s. E. Galvanized steel sheet: ASTM-A526 with 2.2 oz. copper bearing, G165 coating with regular spangle appearance Galvanized steel sheet shall not be used as an exposed surface unless specifically specified. Where specified for use as an exposed surface, galvanized steel shall be finished with one coat primer and two coats air dry enamel, silver gray unless otherwise specified. F. Structural Steel:New material, cleaned and primed. 120A, G. Sound deadening material under metal work surfaces: Non-absorbent, hard drying, sound deadening compound for permanent adhesion to metal that does not chip, flake, or blister in 1/8 thickness Aquaplas F- gray, or approved equivalent. H. Plywood: As specified in Section 11402, Fabricated Casework and Finish Carpentry. I. Particle board will not be permitted for use as a panel substrate, as a backup, or in any other fabricated form, unless specified in the Itemized List of Equipment. J. Laminated plastic face sheet for flatwork (vertical and horizontal): General Purpose Grade, 0.05 thick. Manufactured by Formica, Nevamar, or Wilsonart, unless otherwise specified, with an abrasion/wear resistant surface where available. Color and finish to be selected by the Consultant from manufacturer s standard range. K. Laminated plastic backing sheet: Shall be the selected face sheet manufacturer s standard, 0.02 thick. L. Solid polymer sheet: As specified in section 11402, Fabricated Casework and Finish Carpentry. M. Any fabrication of solid polymer product must be performed by a qualified Tradesman or firm having the necessary skill and experience acceptable
3 2.2 CONSTRUCTION A. Tops to the Product manufacturer. Metal 1. Stainless steel tops: 14 gauge continuous sheets all welded. Tops made of multiple sheets shall have all joints and seams continuously welded, ground smooth and polished to blend with adjacent surfaces. surface grain on adjacent sheets to be aligned wherever possible. 2.3 WELDING 2. Stainless steel tables with sinks shall have a marine type edge on all Open sides unless otherwise specified. 3. Reinforcing shall be minimum 12 gauge stainless steel 4 x 1 channel, Arranged so that forms are concealed from normal view. Secure reinforcing to tops with stud welding, and silicone if necessary. Tops supporting coffee urns, ice dispensers or other heavy equipment shall have additional bracing to support the heavy loads. A. All welding shall conform to national and state requirements and related Specifications, and be performed by certified technicians. Exposed welds shall be continuous, filed or ground smooth and flush, and polished to match adacent surfaces. Use methods that minimize distortion and develop strength and corrosion resistance base metal. B. Electric seamless welding shall utilize low carbon filler rod, coated with non- Carbonaceous flux with sufficient chromium and nickel so that the deposited metal and the original metal have the same composition. C. Welds shall be free from gas holes, pits, cracks, dis-colorization and other imperfections. D. Provide full penetration welds for full-joint length. Welded joints shall be butt fitted, properly jigged, flat continuous, ground smooth and polished for exposed conditions
4 E. Where soldering is desirable, it shall be made with tin-lead solder. In no case shall soldering be relied upon for the stability of the seam or joint. Soldering shall serve only as a filler to prevent leakage, and shall not be considered as a replacement for welding or brazing. F. Butt joints made by spot welding or riveting straps under seams and filling with Solder, puddle welds and exposed screws are not acceptable. G. Exposed dimples from welding studs on underside of tops other surfaces is not Acceptable. Polish surface to match and blend with adjacent surfaces. H. Welds on galvanized steel shall be smooth and strong. Remove all slag and carbonization. Where galvanizing has been burned off, touch up on both sides with high grade aluminum paint. 2.4 FABRICATION A. Before fabrication commences, check all dimensions and conditions at the building site, including means of access into and through the building to the area where equipment is to be set in place, for all conditions affecting the delivery and installation of the equipment. B. Fix and assemble work in the shop wherever possible. Execute the work in accordance with design details and shop drawings which have been reviewed and accepted by the Consultant. Where complete or final shop fabrication is not possible, make a trial assembly in the shop prior to delivery. C. Workmanship shall be of the best grade of modern shop and field practice for manufacturers who specialize in this work. D. Fabricate and erect work square, plumb, straight, true, rigid and accurately fitted. Provide adequate reinforcing and anchorage in all places
5 E. Insulate where necessary to prevent electrolysis between dissimilar metals, and corrosion between metal and masonry or concrete. F. All drillings to be reamed and exposed edges left clean and smooth. G. Do not use pop rivets unless clearly noted on shop drawings, and then only if Such drawings have been reviewed/acknowledged. H. Accurately follow the methods of construction, reinforcement and anchorage, as well as details of finish, fitting and joining, and other data indicated on shop drawings. No deviations from shop drawings which have been reviewed/acknowledged will be permitted during construction of equipment or installation. I. The gauge of metal and methods of construction shall in all cases be adequate for the various conditions to be met, with the requirements of the design details and Specifications considered as minimum. Finished equipment shall be rigid when Assembled and installed. J. Use stainless steel, type 204, for all fastenings and fittings unless otherwise specified. All bolts and screws shall have truss heads, or flat heads which are properly countersunk, at exterior and interior surfaces which are normally visible. Use concealed fastenings throughout, unless otherwise approved by the Consultant. Cap exposed fastener threads, including those inside cabinets, With stainless steel lock washers and stainless steel cap (acorn) nuts. K. Sheet material for counter tops, tables, shelves and similar forms shall be straight lengths, in one continuous sheet if not over 10-0 long. L. Make provisions in the equipment for the proper installation of mechanical and electrical services and connections. Provide pipe slots on equipment with turned up edges and sized to accommodate services. Cut and patch only when necessary. Finish completed installation without rough edges or exposed openings. Provide Welded sleeves, collars, ferrules or escutcheons as required to properly finish and Trim these openings. M. Allow for expansion and contraction of materials. N. Pre-plumb all fabricated items and make all necessary interconnections
6 with the item. All connection terminals shall be easily accessible ready for final connections by the plumbing trades. O. Verify the dimensions and services of all pieces of equipment which may be supplied by others, but are to become a part of a unit specified under this work, in order to endure a proper fit and coordinate installation. P. Supply and install all stainless steel strips and filler pieces necessary to properly finish any individual item or combination of equipment. PART 3 EXECUTION 3.1 EXAMINATION A. Locate and install all counter tops in accordance with Contract Drawings and reviewed shop drawings. B. Complete equipment field assembly, where required. Provide closed butt and hairline contact joints that do not require a filler. Grind field welds smooth, and polish to match adjacent finish. Comply with Welding, Fabricating and Finishing articles of this Section. END OF SECTION
K. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.
DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:
More information1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces.
SECTION 05500- METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationMETALS Commissioning of Metals Structural Steel Framing Steel Studs... 2
~ 05-1 ~ 05 00 00 Metals 05 00 00 METALS... 2 05 08 00 Commissioning of Metals... 2 05 12 00 Structural Steel Framing... 2 05 12 30 Steel Studs... 2 05 45 00 METAL SUPPORT ASSEMBLIES... 2 05 50 00 METAL
More informationSECTION METAL STAIRS
SECTION 05 51 00 METAL STAIRS PART 1 GENERAL 1.1 SUMMARY A. Section includes steel stair frame of structural sections, with closed risers; pan to receive concrete fill stair treads and landings; integral
More informationNorthpointe Renovation EPN #1701 F/A Project #17027 September 8, 2017
SECTION 055213 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION (06415) - PLASTIC COUNTERTOPS
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: SECTION 12 36 23 (06415) - PLASTIC COUNTERTOPS 1. Plastic Laminate a. Countertops and Backsplashes b. Aprons B. Related Sections: 1.02 REFERENCES 1. Section
More information.1 American Institute of Steel Construction (AISC) Specifications for Steel Buildings AISC
05 12 00 STRUCTURAL STEEL FRAMING Page 1 of 3 1 General 1.1 SECTION INCLUDES.1 Structural steel framing and support members 1.2 RELATED SECTIONS.1 Section 05 50 00 Metal Fabrications 1.3 REFERENCES.1 American
More informationPASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017
SECTION 10505 - METAL STUDENT LOCKERS PART 1 - GENERAL 1.01 SCOPE OF WORK A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION HANDRAILS AND RAILINGS. A. Section Cast-In-Place Concrete; coordination with substrate.
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Welded stainless steel railing systems. 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place Concrete; coordination with substrate.
More informationSECTION METAL STAIRS
Tender SECTION 05510 METAL STAIRS PART 1 GENERAL 1.01 SECTION INCLUDES A. This section includes internal and external shop fabricated pre assembled steel stairs with integral handrails and ballustrades
More informationSECTION METAL STUDENT LOCKERS
SECTION 10 51 13 - METAL STUDENT LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES 1. DESCRIPTION: Furnish and install Heavy-Duty Ventilated (HDV) ELITE Metal Lockers, complete, as shown and specified per contract
More informationSECTION METAL EQUIPMENT LOCKERS
SECTION 10 51 13 - METAL EQUIPMENT LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified
More informationPreassembled steel stairs with concrete-filled treads.
SECTION 055113 - PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this
More informationSECTION IMPACT RESISTANT WALL PROTECTION
SECTION 10265 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work under this Section shall include all materials and installation necessary to provide Impact-Resistant Wall Protection including Wall guards,
More informationSECTION METAL ATHLETIC LOCKERS
SECTION 10 51 13 - METAL ATHLETIC LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified
More informationSECTION METAL STAIRS
SECTION 05510 METAL STAIRS PART 1 GENERAL 1.01 SECTION INCLUDES A. Stairs with concrete treads. B. Stairs with metal treads. C. Structural steel stair framing and supports. D. Handrails and guards. 1.02
More informationStudent Services & Classroom Addition
SECTION 055113 - METAL PAN STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION MISCELLANEOUS METALS
PART 1 GENERAL 1.1 WORK OF THIS SECTION A. Contractor shall provide all labor, materials, equipment and incidentals as shown, specified and required to furnish and install all miscellaneous metal fabrications
More informationDIVISION 5 - STRUCTURAL STEEL AND IRON WORK
DIVISION 5 - STRUCTURAL STEEL AND IRON WORK SECTION 05100 STRUCTURAL METAL FRAMING PART 1.00 GENERAL 1.01 SCOPE OF WORK A. Work Included: 1. 2. Structural steel complete in place. Steel joists complete
More information50948-RHN Putney. Friday, 15 December This document includes: Code Section Revision Dated
50948-RHN Putney Friday, 15 December 2017 This document includes: Code Section Revision Dated Z11 Purpose made metalwork 1 Table of Contents Title Z11 Purpose made metalwork Page 3 Z11 Purpose made metalwork
More informationSECTION RESIDENTIAL CASEWORK
PART1 GENERAL 1.01 SECTION INCLUDES A. Vanity cabinets. B. Toilet room casework. C. Casework hardware. 1.02 RELATED REQUIREMENTS A. Section 12 36 00 - Countertops. 1.03 REFERENCE STANDARDS SECTION 12 35
More informationPRESTON HEALTH SERVICES ARCHITECT'S NO MITCHELL-HOLLINGSWORTH NURSING & REHAB ADPH #B
SECTION 05 5213 - PIPE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationThe City of Winnipeg SECTION ST. VITAL LIBRARY RENOVATION PROJECT 6 FERMOR AVE. Page 1 of 5
The City of Winnipeg SECTION 05 50 00 METAL FABRICATIONS ST. VITAL LIBRARY RENOVATION PROJECT 6 FERMOR AVE. Page 1 of 5 Part 1 General 1.1 REFERENCES.1 American Society for Testing and Materials International,
More informationSECTION METAL ATHLETIC LOCKERS
SECTION 10 51 13 - METAL ATHLETIC LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified
More informationSECTION ALUMINUM HANDRAIL SYSTEMS
SECTION 05520 ALUMINUM HANDRAIL SYSTEMS PART 1 - GENERAL 1.01 SUMMARY A. Section includes aluminum handrails and railings. B. Related Work: 1. Section 03300 - Cast-in-Place Concrete C. References: 1. American
More informationHome Depot Page 1 of 5 HDPB Humacao, PR 10/19/09
PART 1 - GENERAL 1.01 SUMMARY A. Types of cold-formed metal framing units include the following: 1. C-shaped steel studs B. Related work specified elsewhere includes but may not be limited to: 1. Section
More informationSECTION 2 DIVISION 05 METALS
SECTION 2 DIVISION 05 METALS DIVISION 5 - METALS Note: This is a guide for Designers only. Contents shall not be used in lieu of specifications as part of the Designer s Contract Documents. GENERAL DESIGN:
More informationSECTION COLD-FORMED METAL TRUSSES
SECTION 054400 COLD-FORMED METAL TRUSSES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION STEEL DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 08110 - STEEL DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General, Supplementary, and Special Conditions and Division 1 Specification
More informationSECTION MISCELLANEOUS METAL FABRICATIONS
SECTION 05500 PART I - GENERAL 1.01 DESCRIPTION: A. Scope: Work under this Section shall include all material and installation necessary to provide Miscellaneous Metal Fabrications, as shown and detailed
More informationSECTION STRUCTURAL METAL FRAMING
SECTION 05100 STRUCTURAL METAL FRAMING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Structural steel framing including lintels, shelf angles, bearing plates, anchor bolts and other items as shown on
More informationDIVISION 10 SPECIALTIES SECTION METAL LOCKERS
DIVISION 10 SPECIALTIES SECTION 10 51 13 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION PIPE AND TUBE RAILINGS PART 1- GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY 1.3 PERFORMANCE REQUIREMENTS
SECTION 055213- PIPE AND TUBE RAILINGS PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION RESILIENT SHEET FLOORING
SECTION 09 65 16 RESILIENT SHEET FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1.
More informationSECTION DECORATIVE METAL AND GLASS RAILING
SECTION 05 73 00 DECORATIVE METAL AND GLASS RAILING PART 1 GENERAL 1.1 SUMMARY A) This section includes both standard and custom handrails as shown in the contract drawings. B) These include aluminum,
More informationPIPE AND TUBE RAILINGS. Evansville Christian High School RELATED DOCUMENTS 1.1
SECTION 055213 - PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this
More informationNational Master Specification (NMS) Section Publisher: Spex.ca Page 1. Approved: RELATED REQUIREMENTS.1 [ ].
National Master Specification (NMS) Section 05 50 00 METAL FABRICATIONS Publisher: Spex.ca Page 1 Approved: 2010-06-30 Part 1 General 1.1 RELATED REQUIREMENTS.1 [ ]. 1.2 REFERENCES.1 CSA International.1
More informationITEM 442 METALS FOR STRUCTURES
AFTER NOVEMBER 1, 2008 ITEM 442 METALS FOR STRUCTURES 442.1 Description. These specifications shall govern for materials such as structural steel, wrought iron, bronze, and other metals used in structures,
More informationSECTION ALTERNATING TREAD STEEL STAIRS
SECTION 05 51 33.23 - ALTERNATING TREAD STEEL STAIRS PART 1 - GENERAL 1.1 SCOPE OF WORK Fabricate and Install metal alternating tread stair assemblies in accordance with the requirements set forth in this
More informationSECTION METAL FRAMED SKYLIGHT. A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system.
SECTION 08625 METAL FRAMED SKYLIGHT PART 1 GENERAL 1.01 SECTION INCLUDES: A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system. B. Fabrication
More informationSECTION PIPE AND TUBE RAILINGS
SECTION 055213- PIPE AND TUBE RAILINGS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationWEC Manufacturing Phone: (901) Website: Itswec.com
All Welded Plus Series Part 1: General 1.1 Construction Requirements: All lockers shall be powder coated steel as design and manufactured by WEC, Memphis, Tennessee. WEC will furnish all labor and materials
More informationSECTION METAL LOCKERS
PART 1 GENERAL 1.1 DESCRIPTION SECTION 10 51 13 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other items or paragraphs not applicable
More informationSECTION ORNAMENTAL ALUMINUM FENCING
SECTION 032300 ORNAMENTAL ALUMINUM FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationHOLLOW METAL DOORS AND FRAMES SECTION HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL
13686.00 HOLLOW METAL DOORS AND FRAMES 081113-1 SECTION 081113 - HOLLOW METAL DOORS AND FRAMES 1.1 RELATED DOCUMENTS: PART 1 - GENERAL A. Drawings and general provisions of Contract, including General
More informationSECTION Temperature Change: 120 deg F, ambient; 180 deg F, material surfaces.
PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Handrails and guardrails. 1.2 PERFORMANCE REQUIREMENTS A. General: In engineering railings to withstand structural loads indicated, determine
More informationHamilton International Air Cargo Logistics Facility Section November 2014 Page 1 of 4
Hamilton International Air Cargo Logistics Facility Section 10 21 14 METAL TOILET COMPARTMENTS Page 1 of 4 Part 1 General 1.1 SECTION INCLUDES.1 Metal toilet compartments, floor mounted. 1.2 RELATED SECTIONS.1
More informationSECTION [ ] COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 08332 [08 33 13] COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Metal Counter
More informationSECTION COLD-FORMED METAL FRAMING
SECTION 05400 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work of this Section shall include all materials and installation necessary to provide all cold formed metal framing. B. This Section includes:
More informationC. Miscellaneous Metal Fabricators are specified elsewhere in Division 5.
SECTION 05 1200 - STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.01 SUMMARY A. Extent of structural steel work is shown on drawings, including schedules, notes and details to show size and location of members,
More informationDIVISION 5 METALS BUSHEY FEIGHT MORIN ARCHITECTS INC. 473 NORTH POTOMAC STREET HAGERSTOWN, MARYLAND FAX:
DIVISION 5 METALS BUSHEY FEIGHT MORIN ARCHITECTS INC. 473 NORTH POTOMAC STREET HAGERSTOWN, MARYLAND 21740 301-733-5600 FAX: 301-733-5612 SECTION 05400 - COLD FORMED METAL FRAMING PART 1 GENERAL 1.1 SECTION
More informationSECTION C. Water Infiltration: Provide manufactured cupolas and dormers that do not allow water infiltration to cupola and dormer interiors.
PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Manufactured exterior cupolas. 2. Manufactured dormers. 3. Historical locomotive weather Vane. 1.2 PERFORMANCE REQUIREMENTS A. General:
More informationProject No: Pakenham Branch Library, Pakenham, Ontario Section
DECEMBER, 2016 Page 1 of 5 1 GENERAL 1.01 RELATED SECTIONS.1 Section 01 33 00 - Submittal Procedures..2 Section 01 78 00 - Closeout Submittals. 1.02 REFERENCES.1 American Society for Testing and Materials
More informationSCI-FAB Product Specifications. Casework Section 1. Part 1 General
SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.
More informationA. WCMA A Safety of Corded Window Covering Products; Window Covering Manufacturers Association; (ANSI/WCMA A101.1)
SECTION 12 21 14 VERTICAL LOUVER BLINDS PART 1 - GENERAL 1.1 SECTION INCLUDES A. Vertical slat louver blinds and operating hardware. 1.2 REFERENCE STANDARDS A. WCMA A100.1 - Safety of Corded Window Covering
More informationPIPE AND TUBE RAILINGS
SECTION 05521 - PIPE AND TUBE RAILINGS PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More information1. Base plates, setting plates and anchor rods for columns. 8. Lintels if connected to structural steel columns.
PAGE 051200-1 SECTION 051200 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,
More informationA. This Section includes the following: 1. Aluminum pipe and tube handrails and railings.
SECTION 05521 - PIPE AND TUBE RAILINGS PART 1 - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationAmerican Metal Specialties, Inc.
American Metal Specialties, Inc. www.cablerailings.com (253) 272-9344 (253) 627-3843 Fax PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 05 73 00 STAINLESS STEEL ORNAMENTAL HANDRAILS AND RAILINGS For best
More informationSECTION ORNAMENTAL WELDED STEEL FENCING
SECTION 032300 ORNAMENTAL WELDED STEEL FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSECTION RESILIENT SHEET FLOORING
SECTION 09665 RESILIENT SHEET FLOORING PART 1 - GENERAL 1.1 DESCRIPTION A. This Section specifies the installation of sheet flooring with backing and integral cove base. 1.2 RELATED WORK A. Color and pattern:
More informationSERIES SA30 STEEL/ALUMINUM FIXED DETENTION WINDOWS SECTION 08651
SERIES SA30 STEEL/ALUMINUM FIXED DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows as
More informationSECTION WELDED STEEL PICKET FENCE. 1. Fusion welded and rackable ornamental steel picket fence system.
PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Fusion welded and rackable ornamental steel picket fence system. B. Related sections: 1. Section 03310 Concrete Work for post support. 2. Section 09960
More informationDIVISION 5 METALS COLD FORMED METAL FRAMING Structural Metal Stud Framing
05 40 00 COLD FORMED METAL FRAMING 05 41 00 Structural Metal Stud Framing 05 50 00 METAL FABRICATIONS 05 51 00 Metal Stairs 05 51 13 Metal Pan Stairs 05 52 00 Metal Railings 05 52 13 Pipe and Tube Railings
More informationSECTION HOLLOW METALWORK. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 081113 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationSECTION / HEAVY DUTY WIRE MESH WINDOW GUARDS
SECTION 10605 / 10 22 13 HEAVY DUTY WIRE MESH WINDOW GUARDS ** NOTE TO SPECIFIER ** heavy duty woven wire mesh partitions, wire mesh infill panels, window guards, and area guarding.. This section is based
More informationSECTION PHENOLIC LOCKERS AND BENCHES. B. Section Gypsum Board Area Separation Wall Assemblies.
SECTION 10 51 29 PHENOLIC LOCKERS AND BENCHES PART 1 GENERAL 1.1 SECTION INCLUDES A. Phenolic lockers, hardware and accessories. B. Phenolic pedestal benches. C. Phenolic cubbies. 1.2 RELATED SECTIONS
More informationTrex Commercial Products page Metal Railing
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Classic Railings (Picket). B. GridGuard Railings (Mesh). C. Post Rail (Glass). D. Tensiline Railings (Cable). E. Track Rail (Glass).
More informationSECTION FABRICATED ENGINEERED STRUCTURES. A. Pre-engineered, shop-fabricated structural steel building with formed purlin framing.
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 13 34 00 FABRICATED ENGINEERED STRUCTURES A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
More informationB. Shop Drawings: For metal lockers. Include plans, elevations, sections, details, and attachments to other work.
SECTION 10 5113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationSECTION VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND EQUIPMENT
SECTION 230548 - VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary
More informationC S I S E C T I O N STAINLESS STEEL DOORS AND FRAMES SPECIFICATIONS
This section is based on products manufactured by Next Door Company, at the following address: 1840 North Commerce Parkway Suite 1 Weston, FL 33326-3200 tel. (954) 772-6666 or (888) 791 4450 fax (954)
More informationSECTION HANDRAILS AND RAILINGS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES Display hidden notes to specifier. (Don't know how? Click Here) A. Classic Railings (Picket). B. GridGuard Railings (Mesh). C. Post
More informationThe fire resistance required for doors in this building is 1 (one) hour resistance in compliance with the below general specifications:
Query No.1 ; we need more specs. about fire resistant doors Answer to Query No. 1: The fire resistance required for doors in this building is 1 (one) hour resistance in compliance with the below general
More informationH D P SOLID PHENOLIC FLOOR BRACED COMPARTMENTS SECTION FB TOILET PARTITIONS
3501 East La Palma Avenue - Anaheim, California 92806 PART 1 GENERAL Ph: 714-666-0108 and 714-666-0109 Fax: 714-666-0110 www.weisrobart.com H D P SOLID PHENOLIC FLOOR BRACED COMPARTMENTS 1.1 RELATED DOCUMENTS:
More informationSECTION ACCORDION FOLDING PARTITIONS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 22 26.13 ACCORDION FOLDING PARTITIONS SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationSECTION WALL AND DOOR PROTECTION
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 26 00 WALL AND DOOR PROTECTION SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable to
More informationDIVISION 5 METALS Metal Fabrication
DIVISION 5 METALS 05500 Metal Fabrication SECTION 05500 PART 1 GENERAL 1.1 INTENT OF SECTION.1 This section specifies requirements for the supply and installation of all miscellaneous metal fabrications,
More informationSECTION VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this Section. 1.2 SUMMARY A. This Section includes the
More informationSECTION MISCELLANEOUS METALS THIS SECTION TO BE INCLUDED IN SUB BID FOR SECTION MISCELLANEOUS AND ORNAMENTAL IRON
SECTION 055000 THIS SECTION TO BE INCLUDED IN SUB BID FOR SECTION 050001 MISCELLANEOUS AND ORNAMENTAL IRON PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a
More informationDIVISION 6 SOLID SURFACE FABRICATIONS SECTION 06650
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including general and supplementary conditions and Division 1 Specification Sections, apply to this Section. 1.2
More informationCOLLEGE CLASSROOM & DORMITORY SPECIFICATION SECTION 08100
COLLEGE CLASSROOM & DORMITORY SPECIFICATION SECTION 08100 Part 1 General 1.01 Work Included A. The work under this section shall include the furnishing of all items shown on the drawings and as specified,
More informationSECTION FOOD DISPENSING EQUIPMENT- SNEEZE GUARDS AND PARTITION POSTS
Page 1 of 17 SECTION 11 4600 FOOD DISPENSING EQUIPMENT- SNEEZE GUARDS AND PARTITION POSTS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 055113 - METAL PAN STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSection PANEL SIGNAGE
Section 10 14 23 PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including FDOT DIVISION I GENERAL REQUIREMENTS & COVENANTS Specification Sections,
More informationSERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651
SERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows
More informationSECTION ALUMINUM RAILINGS
SECTION 05522 ALUMINUM RAILINGS PART 1 GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Aluminum pipe and tube railings. B. Related Sections include the following: 1. Division 5 Section "Ornamental
More informationB. Shop Drawings: Include plans, elevations, sections, details, and attachments.
SECTION 055119 - METAL GRATING STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION TOILET PARTITIONS. A. Section Structural Steel: Supports for ceiling hung compartments.
SECTION 10155 TOILET PARTITIONS PART 1 GENERAL 1.1 SECTION INCLUDES A. Stainless steel toilet compartments. 1.2 RELATED SECTIONS A. Section 05120 - Structural Steel: Supports for ceiling hung compartments.
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092216 - NON-STRUCTURAL METAL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationFabricate and Install metal alternating tread stair assemblies in accordance with the requirements set forth in this section.
SECTION - ALTERNATING TREAD STEEL STAIRS PART 1 - GENERAL 1.1 SCOPE OF WORK Fabricate and Install metal alternating tread stair assemblies in accordance with the requirements set forth in this section.
More informationHOTEL SPECIFICATION SECTION 08100
Part 1 General HOTEL SPECIFICATION SECTION 08100 1.01 Work Included A. The work under this section shall include the furnishing of all items shown on the drawings and as specified including, but not limited
More informationSECTION DETENTION WINDOW SCREENS. 1. Detention screens for interior and exterior installations at exterior windows in existing buildings.
SECTION 08 56 66 DETENTION WINDOW SCREENS SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: SPEC
More informationHDPE SOLID POLYMER-PLASTIC FLOOR BRACED COMPARTMENTS SECTION FB WEIS/POLY TOILET PARTITIONS
3501 East La Palma Avenue - Anaheim, California 92806 Ph: 714-666-0108 and 714-666-0109 Fax: 714-666-0110 www.weisrobart.com PART 1 GENERAL HDPE SOLID POLYMER-PLASTIC FLOOR BRACED COMPARTMENTS SECTION
More informationUniversity Apartments on Brooklyn PROJECT MANUAL
Section 122100 Horizontal Louver Blinds University Apartments on Brooklyn PART 1 - GENERAL 1.1 SECTION INCLUDES A. Horizontal slat louver blinds. B. Operating hardware. 1.2 RELATED SECTIONS A. Section
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey. A. This Section includes the following sanitary drainage piping specialties:
SECTION 221319 - SANITARY WASTE PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following sanitary drainage piping specialties: 1. Cleanouts. 2. Floor drains. 3. Roof flashing
More informationStudent Services & Classroom Addition. A. This Section includes the following sanitary drainage piping specialties:
SECTION 221319 - SANITARY WASTE PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following sanitary drainage piping specialties: 1. Cleanouts. 2. Floor drains. 3. Roof flashing
More informationSECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION
Page 210500-1 SECTION 210500 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationJONES AIRWAY, LLC CLEVELAND REGIONAL JETPORT SECTION STRUCTURAL STEEL
CLEVELAND REGIONAL JETPORT 05 1200-1 PART 1 - GENERAL SECTION 05 1200 STRUCTURAL STEEL 1.1 RELATED SPECIFICATION SECTIONS: A. Bolting of wood to steel, steel anchors for work of other trades, concrete
More informationSECTION ALTERNATING TREAD STEEL STAIRS
SECTION 05 51 33.23 - ALTERNATING TREAD STEEL STAIRS PART 1 - GENERAL 1.1 SCOPE OF WORK Fabricate and install carbon steel or stainless steel alternating tread stair assemblies in accordance with the requirements
More information