EXTERIOR RESEARCH & DESIGN, LLC. Certificate of Authorization # Christian Street Oxford, CT PHONE: (203) FAX: (203)

Transcription

1 EVALUATION REPORT Carlisle SynTec Systems P.O. Box 7000 Carlisle, PA (717) EXTERIOR RESEARCH & DESIGN, LLC. Certificate of Authorization # Christian Street Oxford, CT PHONE: (203) FAX: (203) Evaluation Report C R7 FL14165-R7 Date of Issuance: 10/27/2010 Revision 7: 02/13/2017 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for compliance with the 5 th Edition (2014) Florida Building Code sections noted herein. DESCRIPTION: Carlisle Single Ply Roof Systems LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. Trinity ERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words Trinity ERD Evaluated may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 5, plus a 36-page Appendix. Prepared by: Robert J.M. Nieminen, P.E. Florida Registration 59166, Florida DCA ANE1983 The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 02/13/2017. This does not serve as an electronically signed document. Signed, sealed hardcopies have been transmitted to the Product Approval Administrator and to the named client CERTIFICATION OF INDEPENDENCE: 1. Exterior Research & Design, LLC. d/b/a Trinity ERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Exterior Research & Design, LLC. d/b/a Trinity ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither Trinity ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose.

2 ROOFING SYSTEMS EVALUATION: 1. SCOPE: Product Category: Roofing Sub-Category: Single Ply Roof Systems Compliance Statement: Single Ply Roof Systems, as produced by Carlisle SynTec Systems, have demonstrated compliance with the following sections of the 5 th Edition (2014) Florida Building Code through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein. 2. STANDARDS: Section Property Standard Year Wind FM Impact FM Physical Properties ASTM D Wind TAS REFERENCES: Entity Examination Reference Date ACRC (TST4671) TAS /30/2007 ACRC (TST4671) TAS /23/2010 ACRC (TST4671) TAS /29/2011 ACRC (TST4671) TAS /01/2015 ACRC (TST4671) TAS /04/2016 ATI (TST1558) TAS /06/2009 ATI (TST1558) TAS 114 C /11/2012 CTL (TST 1577) TAS 114 CTLA-105R 10/13/2008 CTL (TST 1577) TAS 114 CTLA-105R-1 10/13/2008 CTL (TST 1577) TAS 114 CTLA-105R-2 10/13/2008 CTL (TST 1577) TAS 114 CTLA-106R 10/16/2008 CTL (TST 1577) TAS 114 CTLA-106R-1 10/16/2008 CTL (TST 1577) TAS 114 CTLA-106R-2 10/16/2008 CTL (TST 1577) TAS 114 CTLA-106R-3 10/16/2008 CTL (TST 1577) TAS 114 CTLA-106R-4 10/16/2008 CTL (TST 1577) TAS 117 CTLA 111R 01/13/2009 ERD (TST 6049) Physical Properties C /30/2009 ERD (TST 6049) Physical Properties C /30/2009 ERD (TST 6049) Physical Properties F R2 02/27/2012 ERD (TST 6049) Physical Properties F R2 02/27/2012 ERD (TST 6049) FM 4470/FM 4474 SFS-SC /29/2016 ERD (TST 6049) Physical Properties CRL-SC /20/2016 ERD (TST 6049) Physical Properties CRL-SC /20/2016 ERD (TST 6049) FM 4470/FM 4474 CTL /27/2017 FM Approvals (TST1867) FM /23/1999 FM Approvals (TST1867) FM /27/2003 FM Approvals (TST1867) FM /05/2003 FM Approvals (TST1867) FM 4470/FM /07/2005 FM Approvals (TST1867) FM 4470/FM /11/2006 FM Approvals (TST1867) FM 4470/FM /20/2006 FM Approvals (TST1867) FM 4470/FM /20/2006 FM Approvals (TST1867) FM 4470/FM /18/2006 FM Approvals (TST1867) FM 4470/FM /05/2007 FM Approvals (TST1867) FM 4470/FM /25/2007 FM Approvals (TST1867) FM 4470/FM /22/2007 FM Approvals (TST 1867) FM 4470/FM /27/2007 FM Approvals (TST1867) FM 4470/FM /16/2007 FM Approvals (TST1867) FM 4470/FM /21/2008 FM Approvals (TST1867) FM 4470/FM /13/2008 FM Approvals (TST1867) FM 4470/FM /15/2008 Exterior Research and Design, LLC. Evaluation Report C R7 Certificate of Authorization #9503 FBC NON-HVHZ EVALUATION FL14165-R7 Carlisle SynTec Systems Revision 7: 02/13/2017 Page 2 of 5

3 Entity Examination Reference Date FM Approvals (TST1867) FM 4470/FM /14/2009 FM Approvals (TST1867) FM 4470/FM /08/2009 FM Approvals (TST1867) FM 4470/FM /13/2009 FM Approvals (TST1867) FM 4470/FM /13/2010 FM Approvals (TST1867) FM 4470/FM /14/2010 FM Approvals (TST1867) FM 4470/FM /15/2010 FM Approvals (TST1867) FM 4470/FM /04/2010 FM Approvals (TST1867) FM 4470/FM /11/2010 FM Approvals (TST1867) FM 4470/FM /13/2010 FM Approvals (TST1867) FM 4470/FM /06/2010 FM Approvals (TST1867) FM 4470/FM /17/2010 FM Approvals (TST1867) FM 4470/FM /07/2011 FM Approvals (TST1867) FM 4470/FM /03/2011 FM Approvals (TST1867) FM 4470/FM /08/2011 FM Approvals (TST1867) FM 4470/FM /23/2011 FM Approvals (TST1867) FM 4470/FM /23/2011 FM Approvals (TST1867) FM 4470/FM /25/2011 FM Approvals (TST1867) FM 4470/FM /13/2011 FM Approvals (TST1867) FM 4470/FM /22/2011 FM Approvals (TST1867) FM 4470/FM /01/2011 FM Approvals (TST1867) FM 4470/FM /16/2011 FM Approvals (TST1867) FM 4470/FM /27/2012 FM Approvals (TST1867) FM 4470/FM /19/2012 FM Approvals (TST1867) FM 4470/FM /14/2012 FM Approvals (TST1867) FM 4470/FM /13/2012 FM Approvals (TST1867) FM 4470/FM /18/2012 FM Approvals (TST1867) FM 4470/FM /02/2012 FM Approvals (TST1867) FM 4470/FM /23/2012 FM Approvals (TST1867) FM 4470/FM /20/2012 FM Approvals (TST1867) FM 4470/FM /07/2013 FM Approvals (TST1867) FM 4470/FM /14/2013 FM Approvals (TST1867) FM 4470/FM /24/2014 FM Approvals (TST1867) FM 4470/FM /16/2014 FM Approvals (TST1867) FM 4470/FM (data) 01/08/2016 FM Approvals (TST1867) FM 4470/FM /25/2016 FM Approvals (TST1867) FM 4470/FM /10/2016 FM Approvals (TST1867) FM 4470/FM /20/2016 FM Approvals (TST1867) FM 4470/FM /28/2016 Miami-Dade (CER1592) TAS /08/2012 Miami-Dade (CER1592) TAS /05/2013 UL, LLC (QUA9625) Quality Control ML File R /07/2012 UL, LLC (QUA9625) Quality Control Follow Up Procedure, R /27/2015 UL, LLC (QUA9625) Quality Control Inspection Report, R8103 (NJ) 11/10/2016 UL, LLC (QUA9625) Quality Control Inspection Report, R8103 (IL) 11/22/ PRODUCT DESCRIPTION: The following roof covers are mechanically attached or fully adhered to Approved substrates using fasteners, stress plates and adhesives, as outlined in the Limitations / Conditions of Use herein. PVC membranes are nominal 50, 60 or 80-mil (1.3, 1.5 or 2.0-mm), PVC, polyester scrim reinforced, single-ply roof membranes. PVC FRS membranes are nominal 50, 60 or 80-mil (1.3, 1.5 or 2.0-mm), PVC, fiberglass reinforced, single-ply roof membranes. KEE HP membranes are nominal 50, 60 or 80-mil (1.3, 1.5 or 2.0-mm), KEE modified PVC, polyester scrim reinforced, single-ply roof membranes. PVC KEE membranes are nominal 50, 60 or 80-mil (1.3, 1.5 or 2.0-mm), synthetic fiber reinforced, thermoplastic single-ply roof membranes. Exterior Research and Design, LLC. Evaluation Report C R7 Certificate of Authorization #9503 FBC NON-HVHZ EVALUATION FL14165-R7 Carlisle SynTec Systems Revision 7: 02/13/2017 Page 3 of 5

4 membranes are nominal 50, 60 or 80-mil (1.3, 1.5 or 2.0-mm), synthetic fiber reinforced, thermoplastic single-ply roof membrane with a nonwoven polyester felt backing. 5. LIMITATIONS: 5.1 This is a building code evaluation. Neither Trinity ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in HVHZ jurisdictions. 5.3 Refer to a current UL Roofing Materials Directory for fire ratings of this product. 5.4 For steel deck installations, foam plastic insulation shall be separated from the building interior in accordance with FBC unless the exceptions stated in FBC and apply. 5.5 The roof system evaluation herein pertains to above-deck roof components. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. Load resistance of the roof deck shall be documented through proper codified and/or FBC Approval documentation. 5.6 For recover installations, the existing roof shall be examined in accordance with FBC For mechanically attached insulation or membrane or strip-bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with FBC Chapter 16. Zones 2 and 3 shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are ANSI/SPRI WD1, FM Loss Prevention Data Sheet 1-29, RAS 117 and RAS 137. Assemblies marked with an asterisk* carry the limitations set forth in Section of FM Loss Prevention Data Sheet 1-29 (January 2016) for Zone 2/3 enhancements. 5.8 For assemblies with all components fully bonded in place, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16. No rational analysis is permitted for these systems. 5.9 For mechanically attached insulation or membrane over existing roof decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing and analysis shall be in accordance with ANSI/SPRI FX-1 or TAS For bonded insulation or membrane over existing substrates in a re-roof (tear off) or recover installation, the existing deck or existing roof surface shall be examined for compatibility with the adhesive to be installed. If any surface conditions exist that bring system performance into question, field uplift testing in accordance with ANSI/SPRI IA-1, ASTM E907, FM Loss Prevention Data Sheet 1-52 or TAS 124 shall be conducted on mock-ups of the proposed new roof assembly For bonded insulation or membrane over existing substrates in a recover installation, the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the Authority Having Jurisdiction, as documented through field uplift testing in accordance with ANSI/SPRI IA-1, ASTM E907, FM Loss Prevention Data Sheet 1-52 or TAS Metal edge attachment (except gutters), shall be designed and installed for wind loads in accordance with FBC Chapter 16 and tested for resistance in accordance with ANSI/SPRI ES-1 or RAS 111, except the basic wind speed shall be determined from FBC Figure All products in the roof assembly shall have quality assurance audit in accordance with the FBC and F.A.C. Rule 61G20-3. Exterior Research and Design, LLC. Evaluation Report C R7 Certificate of Authorization #9503 FBC NON-HVHZ EVALUATION FL14165-R7 Carlisle SynTec Systems Revision 7: 02/13/2017 Page 4 of 5

5 6. INSTALLATION: 6.1 Single Ply Roof Systems shall be installed in accordance with Carlisle SynTec Systems published installation instructions, subject to the Limitations / Conditions of Use noted herein. 6.2 System attachment requirements for wind load resistance are set forth in Appendix 1. MDP = Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads, and reflects the ultimate passing pressure divided by 2 (the 2 to 1 margin of safety per FBC has already been applied). Refer to FBC 1609 for determination of design wind loads. 6.3 For mechanically fastened membrane systems (Type D) over profiled steel deck, membrane shall be installed running perpendicular to steel deck flutes. 7. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 8. MANUFACTURING PLANTS: Contact the noted QA agency for information on product locations covered by QA procedures. 9. QUALITY ASSURANCE ENTITY: UL, LLC. QUA9625; (414) ; karen.buchmann@ul.com - THE 36-PAGES THAT FOLLOW FORM PART OF THIS EVALUATION REPORT - Exterior Research and Design, LLC. Evaluation Report C R7 Certificate of Authorization #9503 FBC NON-HVHZ EVALUATION FL14165-R7 Carlisle SynTec Systems Revision 7: 02/13/2017 Page 5 of 5

6 APPENDIX 1: ATTACHMENT REQUIREMENTS FOR WIND UPLIFT RESISTANCE Table Application Type Description Page 1A Wood New, Reroof (Tear-Off), Recover C Mechanically Insulation, Bonded Roof Cover 4 1B Wood New, Reroof (Tear-Off), Recover D Insulated, Mechanically Roof Cover 5 2A Steel or Concrete New, Reroof (Tear-Off), Recover B-1 Mech. Base Insulation, Bonded Top Insulation, Bonded Roof Cover 6-8 2B Steel New, Reroof (Tear-Off), Recover B-2 Mech. Thermal Barrier, Bonded Vapor Barrier, Bonded Insulation, Bonded Roof Cover 9 2C Steel or Concrete New, Reroof (Tear-Off), Recover C-1 Mechanically Insulation, Bonded Roof Cover D Steel New, Reroof (Tear-Off), Recover C-2 Plate-Bonded Roof Cover E Steel or Concrete New, Reroof (Tear-Off), Recover D Insulated, Mechanically Roof Cover A New, Reroof (Tear-Off) A-1 Bonded Insulation, Bonded Roof Cover B New, Reroof (Tear-Off), Recover C-2 Plate-Bonded Roof Cover B New, Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 26 4A-1 LWIC over Steel New, Reroof (Tear-Off) F LWC to, Bonded Roof Cover A-2 LWC over Concrete New, Reroof (Tear-Off) F LWC to, Bonded Roof Cover 29 5A Gypsum Reroof (Tear-Off) F None-Insulated, Bonded Roof Cover 30 6A Various Recover A-1 Bonded Insulation, Bonded Roof Cover B Steel Recover C-2 Plate-Bonded Roof Cover 34 6C Steel Recover D Insulated, Mechanically Roof Cover 35 6D Various Recover F Non-Insulated, Bonded Roof Cover 36 The following notes apply to the systems outlined herein: 1. The roof system evaluation herein pertains to above-deck roof components. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. Load resistance of the roof deck shall be documented through proper codified and/or FBC Approval documentation. 2. Unless otherwise noted, fasteners and stress plates for insulation attachment shall be as follows. Fasteners shall be of sufficient length for the following engagements: Wood : Sure-Seal HP Fastener with Sure-Seal Insulation Plate. Minimum 1-inch wood penetration. Steel : Sure-Seal HP Fastener with Sure-Seal Insulation Plate. Minimum ¾-inch steel penetration, engage the top flute of the steel deck. : Sure-Seal HD Concrete Fastener, Carlisle CD-10 or HP Concrete Spike (1/4) with Sure-Seal Insulation Plate. Minimum 1-inch embedment. Fasteners installed with a pilot hole in accordance with the fastener manufacturer s published installation instructions. 3. Unless otherwise noted, insulation may be any one layer or of polyisocyanurate, polystyrene, fiberboard, perlite, mineral wool, and/or gypsum-based insulation board that meets the QA requirements of F.A.C. Rule 61G20-3 and is documented as meeting FBC and, for foam plastic, FBC or , when installed with the roof cover. 4. Minimum 200 psi, minimum 2-inch thick lightweight insulating may be substituted for rigid insulation board for System Type C-2 (plate-bonded roof cover) or Type D (mechanically attached membrane), whereby the membrane fasteners are installed through the LWIC to engage the structural steel or deck. The structural deck shall be of equal or greater configuration to the steel and deck listings. 5. Preliminary insulation attachment for System Type D = Minimum four fasteners per 4 x 8 ft board or minimum two fasteners per 4 x 4 ft board. 6. Unless otherwise noted, insulation adhesive application rates are as follows. Ribbon or bead width is at the time of application; the ribbons/beads shall expand as noted in the manufacturer s published instructions: FAST 100 or FAST 100-LV : Full-coverage at 1 gal./square. FAST 100 or FAST 100-LV (RIBBON): Continuous 0.75 to 1-inch wide ribbons, 12-inch o.c. Flexible : Full-coverage at 1 gal./square. Flexible FAST (RIBBON): Continuous 0.75 to 1-inch wide ribbons, 12-inch o.c. FAST Dual-Cartridge (FAST D-C) : Continuous 0.75 to 1-inch wide ribbons, 4-inch o.c. FAST Dual-Cartridge (FAST D-C) (RIBBON): Continuous 0.75 to 1-inch wide ribbons, 12-inch o.c. FAST Bag in a Box Adhesive (BIAB): Continuous 0.75 to 1-inch wide ribbons, 12-inch o.c. FAST Dual-Tank (FAST D-T) : Continuous 0.5-inch wide, wet-beads, 4-inch o.c. Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 1 of 36

7 FAST Dual-Tank (FAST D-T) (RIBBON): Continuous 0.5-inch wide, wet-beads, 12-inch o.c. Note: When installing multiple layers of insulation, FAST Dual-Tank beads shall be placed perpendicular to those placed for attachment of the previous layer. OlyBond 500 (): Continuous 0.75 to 1-inch wide ribbons, 12-inch o.c. using PaceCart or SpotShot. Note: OlyBond 500 Green may be used where OlyBond 500 is referenced. Note: When multiple layers(s) of insulation and/or coverboard are installed in ribbon-applied adhesive, board joints shall be staggered. Note: The maximum edge distance from the adhesive ribbon to the edge of the insulation board shall be not less than one-half the specified ribbons spacing. 7. Unless otherwise noted, all insulations are flat stock or taper board of the minimum thickness noted. Tapered polyisocyanurate at the following thickness limitations may be substituted with the following Maximum Design Pressure (MDP) limitations: LV, FAST D-C or Flexible FAST: MDP psf (Min. 0.5-inch thick) OlyBond 500 (): MDP psf (Min. 0.5-inch thick) 8. Bonded polyisocyanurate insulation boards shall be maximum 4 x 4 ft. 9. For mechanically attached components or partially bonded insulation, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with FBC Chapter 16, and Zones 2 and 3 shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are RAS 117, FM Loss Prevention Data Sheet 1-29 and ANSI/SPRI WD1. Assemblies marked with an asterisk* carry the limitations set forth in Section of FM Loss Prevention Data Sheet 1-29 (January 2016) for Zone 2/3 enhancements. 10. For assemblies with all components fully bonded in place, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16, and no rational analysis is permitted. 11. For mechanically attached components over existing decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the minimum requirements for the system. Testing and analysis shall be in accordance with TAS 105 or ANSI/SPRI FX For existing substrates in a bonded recover or re-roof installation, the existing roof surface or existing roof deck shall be examined for compatibility and bond performance with the selected adhesive, and the existing roof system (for recover) shall be capable of resisting project design pressures on its own merit to the satisfaction of the Authority Having Jurisdiction, as documented through field uplift testing in accordance with ASTM E907, FM Loss Prevention Data Sheet 1-52 or ANSI/SPRI IA For System Type D, steel deck applications, the roof membrane shall be run with its length perpendicular to the steel deck flutes. 14. For Recover Applications using System Type C-2 (Plate Bonded Roof Cover) or Type D (Mechanically Roof Cover), the insulation is optional. Alternatively, min. 0.5-inch HP Recovery Board or SecurShield HD or min inch to inch Dens, Dens Prime, SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board or min. 3/8-inch Insulfoam R-Tech EPS or Fan-Fold may be used as a separator board, preliminarily attached prior to roof cover installation. The separator component shall be documented as meeting FBC and, for foam plastic, FBC Chapter 26, when installed with the roof cover in Recover applications. 15. Lightweight Insulating Concrete (LWC) shall be cast in accordance with FBC Section 1917 to the satisfaction of the Authority Having Jurisdiction. For systems where specific LWC is referenced, refer to current LWC Product Approval for specific deck construction and limitations. For systems where specific LWC is not referenced, the minimum design mix shall be 300 psi. In all cases, the minimum top-coat thickness is 2-inches. For LWC over structural, reference is made to FBC Section , Point For adhered membrane systems, side laps shall be minimum 2-inch wide sealed with min. 1.5-inch heat weld. Unless otherwise noted, membrane adhesive application rates are as follows: Membrane Adhesive Method Rate PVC, PVC KEE, KEE HP or PVC FRS Low VOC PVC Bonding Adhesive Contact (both sides) 1.6 gal/square (½ applied to substrate and ½ applied to membrane) PVC or PVC FRS Aqua Base 120 Bonding Adhesive Contact (both sides) 0.83 to 1 gal/square (½ applied to substrate and ½ applied to membrane) PVC or PVC FRS HydroBond Water-Based PVC BA Wet lay (substrate) 0.75 to 1 gal/square Aqua Base 120 Bonding Adhesive Wet lay (substrate) 0.83 gal/square FAST 100-LV, Flexible FAST, FAST D-C or FAST D-T Wet lay (substrate) RIBBON spaced as noted herein or FULL = 1 gal/square or continuous ribbons, maximum 4-inch o.c. Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 2 of 36

8 17. Vapor barrier options for use over structural deck followed by adhesive-applied insulation carry the following Maximum Design Pressure (MDP) limitations. The lesser of the MDP listings below vs. those in Table 3A applies. VAPOR BARRIER OPTIONS; STRUCTURAL CONCRETE DECK; FOLLOWED BY ADHESIVE-APPLIED INSULATION PER TABLE 3A: Option # Primer Type Vapor Barrier Application Insulation Adhesive Primer VapAir Seal 725TR Self-adhering FAST 100-LV, FULL-coverage at 1 gal/square Primer VapAir Seal 725TR Self-adhering FAST 100-LV, FAST Bag in a Box (BIAB) or FAST Dual Cartridge (RIBBON, 12-inch o.c.) LV Primer VapAir Seal 725TR Self-adhering FAST 100-LV, FULL-coverage at 1 gal/square LV Primer VapAir Seal 725TR Self-adhering FAST 100-LV, FAST Bag in a Box (BIAB) or FAST Dual Cartridge (RIBBON, 12-inch o.c.) CAV-GRIP Primer VapAir Seal 725TR Self-adhering FAST 100-LV, FULL-coverage at 1 gal/square CAV-GRIP Primer VapAir Seal 725TR Self-adhering FAST 100-LV, FAST Bag in a Box (BIAB) or FAST Dual Cartridge (RIBBON, 12-inch o.c.) ASTM D41 SureMB 90TG Base Torch-applied FAST 100-LV or FAST Dual Cartridge (RIBBON, 12-inch o.c.) ASTM D41 SureMB 90 Base Hot-asphalt Hot asphalt at 25 lbs/square ASTM D41 SureMB 90TG Base Torch-applied Hot asphalt at 25 lbs/square MDP = Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads. Refer to FBC 1609 for determination of design wind loads. MDP Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 3 of 36

9 System BAREBACK APPLICATIONS: W-1 W-2 W-3 W-4 W-5 W-6 Min. 23/32-inch plywood Min. 23/32-inch plywood Min. 23/32-inch plywood Min. 23/32-inch plywood Min. 23/32-inch plywood Min. 23/32-inch plywood FLEECEBACK APPLICATIONS: W-7 W-8 Min. 23/32-inch plywood Min. 19/32-inch CDX plywood or wood plank at max. 24-inch spans; 8d ring shank nails, 6-inch o.c. Base Insulation Layer InsulBase, HP-N or HP-W, H- Shield, ENRGY 3 or InsulBase, HP-N or HP-W, H- Shield, ENRGY 3 or (Optional) One or more layers (Optional) One or more layers Min. 1.0-inch Polyiso HP-H, InsulBase, HP-N or HP-W, H- Shield, ENRGY 3 or Min. 1.0-inch Polyiso HP-H, InsulBase, HP-N or HP-W, H- Shield, ENRGY 3 or (Optional) One or more layers, any, loose laid (Optional) One or more layers, any, loose laid TABLE 1A: WOOD DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER Min. 0.5-inch HP Recovery Board Min inch Dens Prime Top Insulation Layer Type Fasteners Attach Min. 1-inch Polyiso HP-H, InsulBase, HP-N or HP-W, H- Shield, ENRGY 3 or InsulBase, HP-N or HP-W, H- Shield, ENRGY 3 or Min. 0.5-inch HP Recovery Board Min inch Dens Prime Min 0.5-inch SECUROCK Gypsum-Fiber Roof Board Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board 1 per per per per 2 Roof Cover (Note 16) PVC or PVC FRS / Aquabase 120 Water Based BA PVC or PVC FRS / Aquabase 120 Water Based BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA MDP -37.5* 1 per 2 PVC, PVC KEE or PVC FRS / Low VOC PVC BA Carlisle InsulFast with Sure-Seal Insulation Plate (aka, Carlisle s Insulation Fastening Plate) 1 per 2 1 per per 2 PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA / LV, Flexible / LV Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 4 of 36

10 System W-9 W-10 Min. 23/32-inch plywood or wood plank at max. 24-inch spans attached using Trufast Spax 8x1-½, Spax 8x2, Spax 10x1½, Spax 10x2 fasteners or OMG Fasten-Master GuardDog 1-5/8 in. or 2 in. screws spaced 6-inch o.c. in the field and spaced 3-inch o.c. at the panel ends. Min. 19/32-inch plywood or wood plank at max. 24-inch spans attached using 8d ring shank nails spaced 6-inch o.c. in the field and #10 ring shank nails spaced 4-inch o.c. at the perimeter TABLE 1B: WOOD DECKS NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D: INSULATED, MECHANICALLY ATTACHED ROOF COVER Insulation Layer (Note 14) Type Attach Membrane Fasteners One or more layers, any One or more layers, any attached attached PVC or KEE HP PVC or KEE HP Carlisle HP-X fasteners and Piranha Plates Carlisle HP-X fasteners and Piranha Plates Roof Cover Fastener Spacing (inch o.c.) Lap Width (inch) Lap Spacing (inch o.c.) Seam Weld (inch) MDP Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 5 of 36

11 System BAREBACK APPLICATIONS: S-1. S-2. S-3. S-4. S-5. S-6. S-7. S-8. S-9. S-10. structural structural structural structural structural structural structural structural structural structural FLEECEBACK APPLICATIONS: TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Base Insulation Layer Top Insulation Layer Type Fastener Attach Type Attach Min. 0.5-inch Dens followed by min. 2.0-inch Insulfoam VIII InsulBase or H-Shield Min. 2.0-inch Polyiso HP-H, InsulBase or H-Shield InsulBase or H-Shield Min. 2.0-inch Polyiso HP-H, InsulBase or H-Shield Min. 0.5-inch Dens followed by min. 2.0-inch Insulfoam VIII InsulBase or H-Shield Min. 0.5-inch Dens followed by min. 3.0-inch Insulfoam VIII InsulBase, HP-N or HP-W, H-Shield, ENRGY 3 or InsulBase, HP-N or HP-W, H-Shield, ENRGY 3 or 1 per per per per per per per per per per 2.0 Min. 1.5-inch Insulam (OSB) Min. 1.0-inch base insulation Min. 1.0-inch base insulation Min inch Dens Prime Min inch Dens Prime Min. 2.0-inch Insulfoam HD Composite Min. 1.0-inch base insulation Min. 1.5-inch Insulam (OSB) Min. 0.5-inch HP Recovery Board Min inch Dens Prime Flexible FAST, FAST D-T (RIBBON, 6-inch o.c.) LV, BIAB, FAST D-T (RIBBON) LV, BIAB, FAST D-T (RIBBON) LV, BIAB, FAST D-T (RIBBON) LV, BIAB, FAST D-T (RIBBON) Flexible FAST, FAST D-T (RIBBON, 6-inch o.c.) LV, FAST D-T (RIBBON, 6-inch o.c.) FAST 100-LV, FAST D-C, FAST D-T (RIBBON, 6-inch o.c.) Roof Cover (Note 16) PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC, PVC FRS, PVC KEE or KEE HP / Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA MDP -37.5* Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 6 of 36

12 System S-11. S-12. S-13. S-14. S-15. S-16. S-17. S-18. S-19. S-20. S-21. structural structural structural structural structural structural structural structural structural structural structural TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Base Insulation Layer Top Insulation Layer Type Fastener Attach Type Attach One or more layers Min. 1.5-inch Polyiso HP-H, InsulBase, HP-N or HP-W, H-Shield, ENRGY 3, or AC Foam II One or more layers Min. 1.5-inch Polyiso HP-H, InsulBase or H-Shield Min. 0.5-inch Dens or Dens Prime Min. 0.5-inch Dens followed by min. 2.0-inch Insulfoam VIII One or more layers Min. 1.5-inch Polyiso HP-H, InsulBase, HP-N or HP-W, H-Shield, ENRGY 3, or AC Foam II One or more layers Min. 1.5-inch Polyiso HP-H, InsulBase or H-Shield InsulBase or H-Shield InsulBase or H-Shield InsulBase or H-Shield Min. 2.0-inch Polyiso HP-H, InsulBase or H-Shield Min. 2.0-inch Polyiso HP-H, InsulBase or H-Shield 1 per per per per per per per per per per per 4.0 Min inch Dens, Dens Prime Min inch Dens Prime Min. 1.5-inch Pactiv GreenGuard Extruded Polystyrene followed by min inch Dens Prime Min. 1.5-inch Insulam (OSB) Additional layers of base insulation Additional layers of base insulation Min. 1.0-inch base insulation Min inch Dens or Dens Prime Min inch Dens Prime Min. 1.0-inch base insulation Min inch Dens or Dens Prime LV, BIAB (RIBBON) FAST D-T (RIBBON) LV, BIAB (RIBBON) Flexible FAST, FAST D-T (RIBBON), 6-inch o.c. LV, BIAB (RIBBON) Roof Cover (Note 16) / FAST 100-LV, FAST D-C, or Flexible FAST (RIBBON, 12-inch o.c.) / FAST D-T (RIBBON, 12-inch o.c.) / FAST 100-LV, FAST D-C, Flexible FAST or FAST D-T (RIBBON, 12-inch o.c.) / FAST 100-LV, Flexible FAST or FAST D-T / FAST 100-LV or Flexible Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 7 of 36 MDP -37.5* -37.5* -37.5* -37.5* FAST D-T (RIBBON) / FAST D-T LV, BIAB, FAST D-T (RIBBON) LV, BIAB (RIBBON) / FAST 100-LV, Flexible FAST or FAST D-T / FAST 100-LV or Flexible FAST D-T (RIBBON) / FAST D-T LV, BIAB, FAST D-T (RIBBON) LV, BIAB (RIBBON) / FAST 100-LV, Flexible FAST or FAST D-T / FAST 100-LV or Flexible

13 System S-22. S-23. S-24. S-25. S-26. S-27. S-28. S-29. structural structural structural structural structural structural structural structural TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY ATTACHED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Base Insulation Layer Top Insulation Layer Type Fastener Attach Type Attach Min. 2.0-inch Polyiso HP-H, InsulBase or H-Shield Min. 0.5-inch Dens followed by min. 2.0-inch Insulfoam VIII InsulBase or H-Shield Min. 0.5-inch Dens followed by min. 3.0-inch Insulfoam VIII InsulBase or H-Shield, SecurShield, H-Shield CG Min. 2-inch Polyiso HP-H, InsulBase, H-Shield Min. 2-inch Polyiso HP-H, InsulBase, H-Shield Min. 2-inch Polyiso HP-H, InsulBase, H-Shield 1 per per per per per per per per 1.6 Min inch Dens Prime Min. 2.0-inch Insulfoam HD Composite Min. 1.0-inch base insulation Min. 1.5-inch Insulam (OSB) Min. 1.0-inch base insulation or minimum 2-inch SecurShield HD Composite Min 0.25-inch SECUROCK Gypsum- Fiber Roof Board Min 0.25-inch SECUROCK Gypsum- Fiber Roof Board Min 0.25-inch SECUROCK Gypsum- Fiber Roof Board Roof Cover (Note 16) MDP FAST D-T (RIBBON) / FAST D-T Flexible FAST, FAST D-T (RIBBON, 6-inch o.c.) LV, FAST D-T (RIBBON, 6-inch o.c.) FAST 100-LV, FAST D-C, FAST D-T (RIBBON, 6-inch o.c.) LV, BIAB, FAST D-T (RIBBON, 6-inch o.c.) / FAST 100-LV, Flexible FAST or FAST D-T / FAST 100-LV, Flexible FAST or FAST D-T / FAST 100-LV, Flexible FAST or FAST D-T / FAST 100, FAST 100-LV, Flexible FAST or FAST D-T / FAST 100-LV, Flexible FAST or FAST D-T / FAST 100-LV, Flexible FAST or FAST D-T / FAST 100-LV, Flexible FAST or FAST D-T * Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 8 of 36

14 System BAREBACK APPLICATIONS: S-30. S-31. S-32. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural FLEECEBACK APPLICATIONS: S-33. S-34. S-35. Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi structural TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-2: MECHANICALLY ATTACHED THERMAL BARRIER, BONDED VAPOR BARRIER, BONDED INSULATION, BONDED ROOF COVER Thermal Barrier Vapor Base Insulation Top Insulation Roof Cover / Adhesive Primer Type Fastener Attach Barrier Type Attach Type Attach (Notes 16) Min. 0.5-inch Dens Prime or min inch SECUROCK Gypsum-Fiber Roof Board Min. 0.5-inch Dens Prime or min inch SECUROCK Gypsum-Fiber Roof Board Min. 0.5-inch Dens Prime or min inch SECUROCK Gypsum-Fiber Roof Board Min. 0.5-inch Dens Prime or min inch SECUROCK Gypsum-Fiber Roof Board Min. 0.5-inch Dens Prime or min inch SECUROCK Gypsum-Fiber Roof Board Min. 0.5-inch Dens Prime or min inch SECUROCK Gypsum-Fiber Roof Board 1 per 2 1 per 2 1 per 2 1 per 2 1 per 2 1 per 2 CAV- GRIP Primer CAV- GRIP Primer CAV- GRIP Primer CAV- GRIP Primer CAV- GRIP Primer CAV- GRIP Primer VapAir Seal 725TR, selfadhering VapAir Seal 725TR, selfadhering VapAir Seal 725TR, selfadhering VapAir Seal 725TR, selfadhering VapAir Seal 725TR, selfadhering VapAir Seal 725TR, selfadhering Min inch Polyiso HP-H, InsulBase, H-Shield Min inch Polyiso HP-H, InsulBase, H-Shield Min inch Polyiso HP-H, InsulBase, H-Shield (Optional) Min inch Polyiso HP-H, InsulBase, H-Shield Min inch Polyiso HP-H, InsulBase, H-Shield Min inch Polyiso HP-H, InsulBase, H-Shield FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON) or FAST 100-LV FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON) or FAST 100-LV FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON) or FAST 100-LV FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON) or FAST 100-LV FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON) or FAST 100-LV FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON) or FAST 100-LV Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board (Optional) Additional layers base insulation (Optional) Additional layers base insulation Min inch Dens Prime (Optional) Additional layers base insulation (Optional) Additional layers base insulation FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON) or FAST 100-LV FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON) FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON, 6-inch o.c.) or FAST 100-LV FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON) or FAST 100-LV FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON) FAST 100-LV, BIAB, FAST D-C, Flexible FAST (RIBBON, 6-inch o.c.) or FAST 100-LV PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA / FAST 100- FAST or FAST D-T (RIBBON, 12-inch o.c.) / FAST 100- FAST or FAST D-T (RIBBON, 12-inch o.c.) / FAST 100- FAST or FAST D-T (RIBBON, 6-inch o.c. or FULL) MDP Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 9 of 36

15 System BAREBACK APPLICATIONS: S-36. S-37. S-38. S-39. S-40. S-41. S-42. S-43. S-44. S-45. S-46. S-47. structural structural structural structural structural structural structural structural structural structural structural structural TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER Base Insulation Layer (Optional) One or more layers Min. 1.5-inch thick, one or more layers, any, loose laid InsulBase, InsulBase, Min. 1.5-inch thick, one or more layers, any, loose laid Min. 1.5-inch thick, one or more layers, any, loose laid (Optional) One or more layers Min. 1.5-inch thick, one or more layers, any, loose laid Min. 1.5-inch thick, one or more layers, any, loose laid InsulBase or H-Shield Min 0.25-inch SECUROCK Gypsum-Fiber Roof Board Min. 0.5-inch HP Recovery Board Top Insulation Layer Type Fasteners Attach Min. 0.5-inch SecurShield HD Plus Min 0.5-inch Dens Prime Min inch SECUROCK Gypsum-Fiber Roof Board Min. 2-inch Polyiso HP-H, InsulBase, H-Shield or SecurShield Min 0.5-inch Dens Prime Min 0.5-inch SECUROCK Gypsum-Fiber Roof Board Roof Cover (Note 16) Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 10 of 36 STEEL: Carlisle InsulFast with Sure- Seal Insulation Plate (aka, Carlisle s Insulation Fastening Plate) CONRETE: STEEL: Carlisle InsulFast with Sure- Seal Insulation Plate (aka, Carlisle s Insulation Fastening Plate) CONCRETE: (Optional) One or more layers Min. 1.5-inch SecurShield Min. 1.0-inch Polyiso HP-H, InsulBase, Min. 1.5-inch thick, one or more layers, any, loose laid Min inch Dens Prime Min 0.25-inch SECUROCK Gypsum-Fiber Roof Board 1 per per per per 4 1 per 4 1 per 4 1 per 4 1 per per per per 2 1 per 2 PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS / Aquabase 120 Water Based BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC / Low VOC PVC BA, HydroBond W-B PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA MDP -37.5* -37.5* -37.5* KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA

16 System S-48. S-49. S-50. S-51. S-52. S-53. S-54. S-55. S-56. S-57. S-58. S-59. structural structural structural structural structural structural structural structural structural structural structural structural TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER Base Insulation Layer Min. 1.0-inch Polyiso HP-H, InsulBase, (Optional) One or more layers InsulBase, (Optional) One or more layers Min. 1.0-inch Polyiso HP-H, InsulBase, Min. 0.5-inch HP Recovery Board Top Insulation Layer Type Fasteners Attach InsulBase, HP-N or HP-W, H- Shield, ENRGY 3 or Min inch Dens Prime Min. 1-inch Polyiso HP-H, InsulBase, HP-N or HP-W, H- Shield, ENRGY 3 or Min. 0.5-inch Dens Prime (Optional) One or more layers Min. 7/16-inch APA rated OSB (Optional) One or more layers Min. 2.0-inch SecurShield (Optional) One or more layers Min. 7/16-inch APA rated OSB InsulBase, InsulBase, (Optional) One or more layers (Optional) One or more layers Min. 0.5-inch SecurShield HD Plus Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board Min. 2.0-inch Polyiso HP-H, InsulBase, HP-N or HP-W, H- Shield, ENRGY 3 or Min. 2.0-inch Polyiso HP-H, InsulBase or H-Shield or Carlisle InsulFast (steel only) with Sure-Seal Insulation Plate (aka, Carlisle s Insulation Fastening Plate) 1 per 2 1 per 2 1 per per per per per 2 1 per per per per per 1.6 Roof Cover (Note 16) PVC, PVC FRS, PVC KEE or KEE HP / Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS / Aquabase 120 Water Based BA PVC or PVC FRS / Low VOC PVC BA, HydroBond W-B PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA MDP KEE HP in Low VOC PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in HydroBond W- B PVC BA PVC or PVC FRS in Low VOC PVC BA or HydroBond W-B PVC BA or PVC KEE or KEE HP in Low VOC PVC BA PVC or PVC FRS in HydroBond W- B PVC BA or KEE HP in Low VOC PVC BA PVC or PVC FRS in HydroBond W- B PVC BA KEE HP in Low VOC PVC BA Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 11 of 36

17 System S-60. S-61. S-62. S-63. S-64. S-65. S-66. S-67. S-68. S-69. structural structural structural structural structural structural structural 80 steel or min. 2,500 psi structural structural 80 steel or min. 2,500 psi structural FLEECEBACK APPLICATIONS: S-70. structural TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER Base Insulation Layer Top Insulation Layer (Optional) One or more layers Min. 7/16-inch APA rated OSB (Optional) One or more layers InsulBase, InsulBase, Min. 1.5-inch thick, one or more layers, any, loose laid InsulBase, InsulBase, InsulBase, (Optional) InsulBase, HP-N or HP-W, H-Shield, ENRGY 3 or Min. 1.5-inch thick, one or more layers, any, loose laid Min. 1.5-inch thick, one or more layers, any, loose laid Type Fasteners Attach Min. 2.0-inch Polyiso HP-H, InsulBase, HP-N or HP-W, H- Shield, ENRGY 3 or Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board Min 0.5-inch Dens Prime Min. 0.5-inch SecurShield HD Plus Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board STEEL: Carlisle InsulFast with Sure- Seal Insulation Plate (aka, Carlisle s Insulation Fastening Plate) CONCRETE: STEEL: Carlisle InsulFast with Sure- Seal Insulation Plate (aka, Carlisle s Insulation Fastening Plate) CONCRETE: Min. 2-inch SecurShield Min 0.5-inch Dens Prime Min 0.25-inch SECUROCK Gypsum-Fiber Roof Board STEEL: Carlisle InsulFast with Sure- Seal Insulation Plate (aka, Carlisle s Insulation Fastening Plate) CONCRETE: STEEL: Carlisle InsulFast with Sure- Seal Insulation Plate (aka, Carlisle s Insulation Fastening Plate) CONCRETE: 1 per per per per per 1 1 per per 1 1 per 1 1 per 1 1 per 1 1 per 2.67 Roof Cover (Note 16) PVC, PVC KEE, KEE HP or PVC FRS / Low VOC PVC BA PVC, PVC KEE or PVC FRS / Low VOC PVC BA PVC, PVC KEE or KEE HP / Low VOC PVC BA MDP KEE HP in Low VOC PVC BA PVC or KEE HP / Low VOC PVC BA PVC, PVC FRS, PVC KEE or KEE HP / Low VOC PVC BA PVC, PVC KEE or KEE HP / Low VOC PVC BA PVC, PVC KEE or KEE HP / Low VOC PVC BA PVC, PVC KEE or KEE HP / Low VOC PVC BA PVC or KEE HP / Low VOC PVC BA / FAST 100- LV, Flexible FAST or FAST D-T -37.5* Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 12 of 36

18 TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER System S-71. S-72. S-73. S-74. S-75. S-76. S-77. S-78. S-79. S-80. structural structural structural structural structural structural structural structural structural structural Base Insulation Layer Min. 1.5-inch thick, one or more layers, any, loose laid Min. 1.5-inch thick, one or more layers, any, loose laid InsulBase, HP-N or HP-W, H-Shield, SecurShield, H-Shield CG, ENRGY 3 or Min. 1.5-inch thick, one or more layers, any, loose laid Min. 1.5-inch thick, one or more layers, any, loose laid Min. 1.5-inch thick, one or more layers, any, loose laid InsulBase, HP-N or HP-W, H-Shield, SecurShield, H-Shield CG, ENRGY 3 or Min. 1.5-inch thick, one or more layers, any, loose laid (Optional) One or, loose laid (Optional) One or, loose laid Min 0.25-inch SECUROCK Gypsum-Fiber Roof Board Top Insulation Layer Type Fasteners Attach Min 0.5-inch Dens Prime Min. 0.5-inch SecurShield HD Plus Min 0.25-inch SECUROCK Gypsum-Fiber Roof Board Min 7/16-inch APA or TECO rated OSB STEEL: Carlisle InsulFast or OMG #12 Roofgrip with SecurFast Insulation Fastening Plate or OMG 3 in. Galvalume Steel Plate CONRETE: Min 15/32-inch plywood Min. 0.5-inch SecurShield HD Plus Min 7/16-inch APA or TECO rated OSB Min 2-inch SecurShield, H-Shield CG, SecurShield HD Composite or H-Shield HD Composite Min. 2-inch SecurShield HD Composite, H-Shield HD Composite 1 per 2 1 per 2 1 per per 1 1 per per per per 1 1 per 1 1 per 1 Roof Cover (Note 16) / FAST 100- LV, Flexible FAST or FAST D-T / FAST 100- LV, Flexible FAST or FAST D-T (RIBBON, 12- inch o.c.) / Flexible FAST or FAST D-T / FAST 100- LV or FAST D-T / FAST 100- LV, Flexible FAST or FAST D-T / Aqua Base 120 BA / Flexible FAST or FAST D-T / FAST 100- LV, Flexible FAST or FAST D-T / FAST 100, FAST 100-LV or FAST D-T / FAST 100- LV MDP Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 13 of 36

19 System RHINOBOND SYSTEMS: S-81. S-82. S-83. S-84. S-85. S-86. S-87. S-88. S-89. Min. 22 ga., type B, Grade 33 steel Min. 22 ga., type B, Grade 33 steel Min. 22 ga., type B, Grade 80 steel Min. 22 ga., type B, Grade 33 steel Min. 22 ga., type B, Grade 80 steel Min. 22 ga., type B, Grade 80 steel Min. 22 ga., type B, Grade 80 steel Min. 22 ga., type B, Grade 80 steel Min. 22 ga., type B, Grade 80 steel Insulation Layer Min. 1-inch thick, one or. Note A. Min. 1-inch thick, one or. Note A. Min. 1-inch thick, one or. Note A. Min. 1.5-inch thick, one or. Note A. Min. 1.5-inch thick, one or, preliminarily attached (Note 14) Min. 1.5-inch thick, one or, preliminarily attached (Note 14) Min. 1.5-inch thick, one or, preliminarily attached (Note 14) Min. 1.5-inch thick, one or, preliminarily attached (Note 14) Min. 1.5-inch thick, one or, preliminarily attached (Note 14) TABLE 2D: STEEL DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-2: PLATE-BONDED ROOF COVER Fasteners Carlisle HP-X Fastener and Rhinobond Plates (PVC) Carlisle HP-X Fastener and Rhinobond Plates (PVC) Carlisle HP-X Fastener and Rhinobond Plates (PVC) Carlisle HP-Xtra Fastener and Rhinobond Plates (PVC) Carlisle HP-X Fastener and Rhinobond Plates (PVC) Carlisle HP-X Fastener and Rhinobond Plates (PVC) Carlisle HP-X Fastener and Rhinobond Plates (PVC) Carlisle HP-X Fastener and Rhinobond Plates (PVC) Carlisle HP-X Fastener and Rhinobond Plates (PVC) Notes: A. For these assemblies, the 8 ft insulation board length is placed perpendicular to the steel deck ribs. B. The plate/fastener offset 12 inch from adjacent rows. ISOWELD INDUCTION WELDING SYSTEMS: S-90. Min. 22 ga., type B, Grade 40 steel One or, min. 1.5-inch Dekfast #15 HS with SFS isoweld PVC Plates (FI-P- 6.8-PVC) Attachment Density / Pattern 1 per 5.33 (6 parts per 4 x 8 ft board) Per FM Loss Prevention Data Sheet 1-29; Note B 1 per 4 (8 parts per 4 x 8 ft board) Per FM Loss Prevention Data Sheet 1-29; Note B 1 per 4 (8 parts per 4 x 8 ft board) Per FM Loss Prevention Data Sheet 1-29; Note B 1 per 4 (8 parts per 4 x 8 ft board) 2 x 2 ft grid pattern 12-inch o.c. in rows max. 120-inch o.c. 18-inch o.c. in rows max. 60-inch o.c. 12-inch o.c. in rows max. 60-inch o.c. 6-inch o.c. in rows max. 120-inch o.c. 6-inch o.c. in rows max. 60-inch o.c. 1 per 6 ft 2 2 x 3-ft grid, staggered Roof Cover PVC, PVC KEE or KEE HP bonded to Rhinobond Plates (PVC) with Rhinobond bonding tool. PVC, PVC KEE or KEE HP bonded to Rhinobond Plates (PVC) with Rhinobond bonding tool. PVC, PVC KEE or KEE HP bonded to Rhinobond Plates (PVC) with Rhinobond bonding tool. PVC, PVC KEE or KEE HP bonded to Rhinobond Plates (PVC) with Rhinobond bonding tool. PVC, PVC KEE or KEE HP bonded to Rhinobond Plates (PVC) with Rhinobond bonding tool. PVC, PVC KEE or KEE HP bonded to Rhinobond Plates (PVC) with Rhinobond bonding tool. PVC, PVC KEE or KEE HP bonded to Rhinobond Plates (PVC) with Rhinobond bonding tool. PVC, PVC KEE or KEE HP bonded to Rhinobond Plates (PVC) with Rhinobond bonding tool. PVC, PVC KEE or KEE HP bonded to Rhinobond Plates (PVC) with Rhinobond bonding tool. PVC or PVC KEE bonded to SFS isoweld PVC Plates with SFS isoweld 3000 stand-up tool. MDP Prepared by: Robert Nieminen, PE Carlisle SynTec Systems; (717) Appendix 1, Page 14 of 36