SECTION GYPSUM WALLBOARD SYSTEMS. A. Gypsum board at new wall partitions or where indicated on drawings. B. ASTM C442 - Gypsum Backing Board
|
|
- Randell Welch
- 6 years ago
- Views:
Transcription
1 SECTION GYPSUM WALLBOARD SYSTEMS PART 1 - GENERAL 1.1 SECTION INCLUDES A. Gypsum board at new wall partitions or where indicated on drawings. 1.2 REFERENCED STANDARDS A. ASTM C36 - Gypsum Wallboard B. ASTM C442 - Gypsum Backing Board C. ASTM Water-Resistant Gypsum Backing Board D. ASTM E119 - Fire Test of Building Construction and Materials E. Gypsum Association, GA Gypsum Board for Walls and Ceilings. F. Gypsum Association GA Recommended Specifications for the Application and Finishing of Gypsum Board. H. UBC - Uniform Building Code. 1.3 QUALITY ASSURANCE A. Manufacturer: Gypsum wallboard, including accessories and fasteners, shall be the products of the same manufacturer. B. Requirements of Regulatory Agencies: 1. Comply with fire-resistance ratings indicated. 2. Provide materials, accessories, and application procedures which have been listed by UL or tested according to ASTM E119 for the type of construction indicated. CAREY & CO., INC. GYPSUM WALLBOARD SYSTEMS
2 3. Work shall comply with the applicable requirements of ASTM C840. C. Allowable Tolerances: 1. Gypsum wallboard surfaces shall have no measurable variation in any 2- foot direction and a maximum variation of 1/8 inch in 10 feet when a straightedge is laid on the surface in any direction. 2. Shim Work as required to comply with specified tolerances. 3. Do not exceed 1/16-inch offset between planes of abutting sheets at edges or ends. 1.4 SUBMITTALS A. Submit under provisions of General Conditions. B. Product Data: Manufacturer's specifications and installation instructions for each type of gypsum wallboard and accessory required. C. Certification: Manufacturer's certification that materials comply with requirements specified herein. 1.5 PRODUCT DELIVERY, STORAGE, AND HANDLING A. Delivery: 1. Deliver materials to the Project site with manufacturer's labels intact and legible. 2. Deliver fire-rated materials bearing the testing agency's label and classification identification. B. Storage: 1. Store materials indoors in a dry area, under cover, and stacked flat, off the floor. 2. Stack wallboard so that long lengths are not over short lengths. C. Handle wallboard in a manner as so to avoid damaging face and edges of sheets. CAREY & CO., INC. GYPSUM WALLBOARD SYSTEMS
3 1.6 JOB CONDITIONS A. Environmental Conditions: 1. Temperature: During cold weather, in areas receiving wallboard installation, maintain temperature range between 55 and 70 degrees F. for 24 hours before, during, and after gypsum wallboard and joint-treatment application. 2. Ventilation: a. Provide ventilation during and following adhesive and jointtreatment application. b. Use temporary air circulators in enclosed areas lacking natural ventilation. c. Under slow drying conditions allow additional drying time between coats of adhesives and joint treatment. d. Protect installed materials from drafts during hot, dry weather. B. Protection: Protect adjacent surfaces against damage and stains resulting from gypsum wallboard Work. PART 2 - PRODUCTS 2.1 MANUFACTURERS - GYPSUM WALLBOARD SYSTEM A. Acceptable manufacturers of gypsum board: 1. U.S. Gypsum. 2. Gold Bond. 3. Approved substitute GYPSUM BOARD -3 A. Provide gypsum board materials in accordance with recommendations of GA 216.
4 B. Standard Gypsum Board: ASTM C36; 5/8 inch thick; maximum permissible length; ends square cut, tapered edges. C. Moisture Resistant Gypsum Board: ASTM C630; standard and UL rated; 5/8 inch thick; maximum permissible length; ends square cut, tapered edges. D. Fire Rated Gypsum Board: ASTM C36; UL rated; 5/8 inch thick; maximum permissible length; ends square cut, tapered edges. E. Gypsum Backing Board: ASTM C442; standard and UL rated, 5/8 inch thick; square edges, ends square cut, maximum permissible length. 2.3 GYPSUM BOARD ACCESSORIES A. Provide gypsum board accossories in accordance with GA 216. B. Metal Trim: Galvanized steel. 1. Corner Beads: 1-1/4 inch flanges. 2. Metal Trim: L bead and LC bead. C. Fasteners: Minimum 1-1/4" drywall screws. Nails permitted only at inside corners inacessible with screw gun. D. Reinforcing Tape, Joint Compoind, Adhesive, and Water: GA 201 and GA 216. PART 3 - EXECUTION 3.1 EXAMINATION A. Verify that site conditions are ready to receive work and opening dimensions are as instructed by manufacturer. B. Beginning of installation means acceptance of substrate. 3.2 PROTECTION A. Protect completed work and historic finishes from damage. -4
5 3.3 GYPSUM BOARD INSTALLATION A. Install gypsum board in accordance with the recommendations of GA 201 and GA 216. Install fire rated partitions in accordance with GA 600 and CBC Tables 43-B and 43-C, and ratings indicated on the Drawings. B. Install single layer standard gypsum board perpendicular to framing. C. Use screws when fastening gypsum board to metal and to wood furring and framing. D. Install moisture resistant gypsum board on toilet room walls and where indicated on the Drawings. Treat cut edges and holes in moisture resistant gypsum board with sealant. E. Place corner beads at external corners. Use longest practical lengths. Place edge trim where gypsum board abutts dissimilar materials and as detailed. 3.4 INSTALLATION - GYPSUM BOARD A. Install gypsum board in accordance with GA 216. B. Use drywall screws to fasten gypsum board to framing substrate. C. Tape, fill, and sand filled joints, edges, corners, openings, and fixings to produce a surface ready to receive veneer finish. D. Feather coats onto adjoining surfaces so that joint camber is maximum 1/32 inch. 3.5 JOINT TREATMENT A. Tape, fill and sand exposed joints, fastener heads, edges and corners to produce smooth finish ready to receive paint finish. B. Feather coats onto adjoining surfaces so that camber is maximum 1/32 inch. 3.6 TOLERANCES A. Maximum Variation from True Flatness: 1/8 inch in 10 feet in any direction. -5
6 END OF SECTION CAREY & CO., INC. GYPSUM WALLBOARD SYSTEMS
SECTION GYPSUM BOARD & SHEATHING SYSTEMS
PART 1!GENERAL! 1.01! SECTION INCLUDES SECTION 09260 GYPSUM BOARD & SHEATHING SYSTEMS! Metal stud wall framing. Metal channel ceiling framing.! Gypsum board.! Sheathing.! Taped and sanded joint treatment.!
More informationSECTION GYPSUM BOARD
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.01 SUMMARY A. Section Includes 1. Gypsum board screw attached to wood framing and furring members, joint treatment, and accessories. 2. Installation of
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09 21 16 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SECTION INCLUDES A. Metal stud wall and ceiling framing, 20 gauge. B. Metal channel suspended ceiling framing. C. Gypsum board. D. Gypsum sheathing.
More informationSECTION GYPSUM BOARD ASSEMBLIES
PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 09260 - A. Metal stud wall framing. Denoted on drawings as "metal studs". B. Metal channel ceiling framing. C. Acoustic insulation and sealant. D. Cementitious
More informationRENOVATE BUILDING 18-C FTFA SECTION GYPSUM BOARD 05/11
SECTION 09 29 00 GYPSUM BOARD 05/11 PART 1 GENERAL 1.1 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text
More informationSECTION GYPSUM BOARD ASSEMBLIES
PART 1 - GENERAL 1.1 SUMMARY SECTION 09 21 16 A. Provide gypsum board assemblies as shown and specified. Work includes: 1. Walls, partitions, and soffits, including metal framing systems. 2. Acoustical
More informationSECTION GYPSUM BOARD
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Interior gypsum wallboard. 2. Tile backing panels. B. Related Sections: 1. Section 012300 Alternates. 1.2 SUBMITTALS A.
More informationSECTION GYPSUM BOARD
SECTION 09250 GYPSUM BOARD PART 1GENERAL 1.1 SUMMARY A. Related Documents: General and Supplementary Conditions of the Contract, Division 1 - General Requirements, and Drawings are collectively applicable
More informationA. Environmental Limitations: Comply with ASTM C 840 requirements or gypsum board manufacturer's written instructions, whichever are more stringent.
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationEXCEL Medical Waste - Equipment Installation Section SECTION GYPSUM BOARD
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.1 DESCRIPTION This section specifies installation and finishing of gypsum board. 1.2 RELATED WORK A. Installation of steel framing members for walls, partitions,
More informationCOOK COUNTY ILLINOIS CONTRACT FOR WORK DOCUMENT NO Countywide Warehouse and Records Storage Center Hawthorne Project TKB No.
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION GYPSUM BOARD
SECTION 09 2900 GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Includes But Not Limited To: 1. Furnish and install gypsum board as described in Contract Documents, except behind ceramic tile. 2. Furnish
More informationSECTION GYPSUM BOARD
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 29 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationSECTION GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.01 SECTION INCLUDES
SECTION 09 2116 - PART 1 GENERAL 1.01 SECTION INCLUDES A. Performance criteria for gypsum board assemblies. B. Acoustic insulation. C. Gypsum sheathing. D. Cementitious backing board. E. Gypsum wallboard.
More informationSECTION GYPSUM BOARD
SECTION 09260 - GYPSUM BOARD PART 1 - GENERAL 1.01 SUMMARY A. Related Documents: Provisions established in General and Supplementary Conditions of the Contract, Division 1 General Requirements, and the
More information1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation blankets
SECTION 09 29 00 - GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation
More informationSECTION GYPSUM BOARD PART 1 - GENERAL
SECTION 09250 - GYPSUM BOARD PART 1 - GENERAL 1.01 DESCRIPTION: A. Work under this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary Conditions
More informationONE SCHOOL STREET SEPTEMBER 18, 2008 GOWANDA, NEW YORK ARCH PROJECT NO
SECTION 09265 - GYPSUM BOARD SHAFT-WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationA. Product Data: For each type of product specified.
SECTION 09260 - GYPSUM BOARD ASSEMBLIES PART 1 - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSAN DIEGO STATE UNIVERSITY PACIFIC CORNERSTONE ARCHITECTS TENOCHCA HALL PROJECT NO FAN COIL UNITS, RESTROOM AND FINISH RENOVATION
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Various gypsum board panels types. 2. Joint treatment materials. 3. Panel trim. 4. Supplementary components and accessories
More informationSECTION GYPSUM BOARD SYSTEM
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 29 00 GYPSUM BOARD SYSTEM A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More informationProject No: Pakenham Branch Library, Pakenham, Ontario Section DECEMBER, 2016 Page 1 of 6
DECEMBER, 2016 Page 1 of 6 1 GENERAL 1.01 RELATED SECTIONS.1 Section 01 33 00 - Submittal Procedures..2 Section 07 21 16 - Batt and Blanket Insulation..3 Section 07 92 10 - Sealants..4 Section 09 91 00
More informationSECTION GYPSUM BOARD SYSTEM
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 29 00 GYPSUM BOARD SYSTEM A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More informationSECTION GYPSUM BOARD
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION COMPOSITE WALL PANELS PART 1 GENERAL 1.01 SECTION INCLUDES
SECTION 07 4243 - PART 1 GENERAL 1.01 SECTION INCLUDES A. Composite wall panel system consisting of aluminum-faced composite panels in a rainscreen application as part of the assembly described below.
More informationStudent Services & Classroom Addition
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationNATIONAL GYPSUM COMPANY Wood Frame Walls And Ceilings Single- And Double-Layer Construction
Walls And Ceilings Single- And Double-Layer Construction 09 9 00/NGC Single-Layer Construction The single-layer construction system consists of a single layer of Gold Bond brand Gypsum Board applied to
More informationCONTRACT NUMBER: W912DQ-08-C % CORRECTED DESIGN 28 JULY 2008
SECTION 092900 - GYPSUM BOARD 1.1 SUMMARY A. This Section includes the following: 1. Interior gypsum board. 2. Tile backing panels. B. Related Sections include the following: 1. Division 06 Section "Rough
More information1 Exam Prep Application and Finishing of Gypsum Board GA Tabs and Highlights
1 Exam Prep Application and Finishing of Gypsum Board GA-216-2013 Tabs and s These 1 Exam Prep Tabs are based on the Gypsum Association GA-216-2013 Application and Finishing of Gypsum Panel Products. Each
More information1 Exam Prep Application and Finishing of Gypsum Board GA Tabs and Highlights
1 Exam Prep Application and Finishing of Gypsum Board GA-216-2016 Tabs and s These 1 Exam Prep Tabs are based on the Gypsum Association GA-216-2016 Application and Finishing of Gypsum Panel Products. Each
More informationGYPSUM BOARD
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationPROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS DAVIS, CALIFORNIA
The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending
More informationGYPSUM BOARD SECTION GYPSUM BOARD PART 1 - GENERAL
13686.00 GYPSUM BOARD 092116-1 1.1 RELATED DOCUMENTS: SECTION 092116 - GYPSUM BOARD PART 1 - GENERAL A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092216 - NON-STRUCTURAL METAL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION (09265) - GYPSUM BOARD SHAFT WALL ASSEMBLIES
SECTION 09 21 16.23 (09265) - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Shaft Enclosures 2. Chase Enclosures 3. Stair Enclosures B. Related Sections: 1.02 DEFINITIONS
More informationEDGEWATER, FLORIDA JUNE 14, 2010
SECTION 09 2900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092650 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationConstruction Standards PAGE
Construction Standards PAGE 092613-1 SECTION 092613 - PART 1 - GENERAL 1.1 M.S.U. ISSUES A. It is the intent of MSU that all gypsum veneer plaster used on its projects will comply with LEED NC 3 Credit
More informationSECTION GYPSUM BOARD ASSEMBLIES
1 PART ONE - GENERAL 1.1 COORDINATION SECTION 09260 GYPSUM BOARD ASSEMBLIES A. Drawings and General provisions of the Contract including General and Supplementary Conditions and Division 1 Specification
More informationAsh Brook Golf Course Scotch Plains, New Jersey
SECTION 092500 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationHome Depot Page 1 of 5 HDPB Humacao, PR 10/19/09
PART 1 - GENERAL 1.01 SUMMARY A. Types of cold-formed metal framing units include the following: 1. C-shaped steel studs B. Related work specified elsewhere includes but may not be limited to: 1. Section
More informationMANUFACTURER S SPECIFICATIONS Section LIMESTONE PLASTER
MANUFACTURER S SPECIFICATIONS Section 09220 LIMESTONE PLASTER LE DÉCOR LIMESTONE PART 1 GENERAL 1.1 General A. This section describes the requirements for furnishing and installing Limestone Plaster. 1.2
More informationHOLLOW METAL DOORS AND FRAMES SECTION HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL
13686.00 HOLLOW METAL DOORS AND FRAMES 081113-1 SECTION 081113 - HOLLOW METAL DOORS AND FRAMES 1.1 RELATED DOCUMENTS: PART 1 - GENERAL A. Drawings and general provisions of Contract, including General
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects SECTION GYPSUM BOARD SHAFT WALL ASSEMBLIES
SECTION 092116.23 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationConstruction Standards PAGE
Construction Standards PAGE 083113-1 SECTION 083113 - PART 1 - GENERAL 1.1 M.S.U ISSUES A. M.S.U. avoids access doors whenever possible by using lay-in type ceilings, but all valves and equipment requiring
More informationMARQUIS Tualatin FIBER-CEMENT SIDING June 15, rev
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes: 1. Reinforced fiber-cement shingle panel siding, 2. Reinforced fiber-cement lap siding. B. Related Sections: 1. Division 1 Section "Quality Requirements"
More informationShowcase Your Space. Not Your Access Panel. Product Features. Shop online at or call
Showcase Your Space Not Your Access Panel Stealth Access Panels are glass fiber reinforced gypsum ceiling access panels that are aesthetically pleasing because they are designed to blend seamlessly into
More informationSAMPLE CONSTRUCTION SPECS 2011 Conspectus, Inc. SECTION GYPSUM BOARD ASSEMBLIES
SAMPLE CONSTRUCTION SPECS 2011 Conspectus, Inc. Specifications, Quality Assurance, Inspections & Investigations for Your Construction Projects 2231 ROUTE 50 P.O. BOX 248 TUCKAHOE, NJ 08250 p: 609.628.2390
More informationSpec Master 5/7/ For each product requiring color and texture selection, provide full size samples.
SECTION 04812 (042012) MECHANICALLY ATTACHED BRICK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092500 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSection GYPSUM DRYWALL
Section 09250 GYPSUM DRYWALL 1.00 GENERAL: A. Gypsum Association Specification GA216 and manufacturer's instruction (whichever is more stringent). 2.00 DRYWALL MATERIALS: A. Exposed Gypsum Board: ASTM
More informationArchitectural Roof Products Guide Specifications
Western States Metal Roofing 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 Architectural Roof Products Guide Specifications FORMED METAL ROOF AND WALL PANELS This Guide Specification
More information1. Non-load-bearing steel framing systems for interior gypsum board assemblies. 2. Suspension systems for interior gypsum ceilings and soffits.
SECTION 09 2216 - PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Non-load-bearing steel framing systems for interior gypsum board assemblies. 2. Suspension systems for interior gypsum ceilings and
More informationConstruction Standards PAGE
Construction Standards PAGE 095113-1 SECTION 095113 - PART 1 - GENERAL 1.1 M.S.U. ISSUES 1. It the intent of MSU that all joint sealants used on its projects will comply with LEED NC 3 Credit Requirements
More informationArchitectural Roof Products Guide Specifications
Western States Metal Roofing 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 Architectural Roof Products Guide Specifications FORMED METAL ROOF AND WALL PANELS This Guide Specification
More informationAddendum No. 1 November 03, 2016
Addendum No. 1 November 03, 2016 Project: Location: Bid Date: Liberal Arts Building Entry & Basement Remodel University of Montana University of Montana Campus Liberal Arts Building 136, 32 Campus Drive,
More informationSECTION NON--STRUCTURAL METAL FRAMING
The Collective Voice of America s Steel Framing Industry The Steel Framing Industry Association (SFIA) is dedicated to expanding the market for cold-formed steel in construction through programs and initiatives
More informationArchitectural Wall Products Guide Specifications
Western States Metal Roofing 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 Architectural Wall Products Guide Specifications FORMED METAL WALL PANELS This Guide Specification is
More informationSECTION CEMENTITIOUS SHEATHING
SECTION 06 16 63 CEMENTITIOUS SHEATHING SPEC WRITER NOTES: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Use this Section for exterior sheathing as a backup
More informationDIVISION: FINISHES SECTION: GYPSUM BOARD ACCESSORIES REPORT HOLDER: CONLAB, INC. dba PREST ON CO.
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1812 Reissued 11/2017 This report is subject to renewal 11/2018. DIVISION: 09 00
More informationSECTION A. ACSE 7 Minimum Loads for Buildings and other Structures.
SECTION 06 12 00 STRUCTURAL INSULATED PANELS ------------------------------------------------------------------------------------------------------------ PART 1- GENERAL ----------------------------- 1.1
More informationSECTION A. ACSE 7 Minimum Loads for Buildings and other Structures.
SECTION 06 12 00 STRUCTURAL INSULATED PANELS ------------------------------------------------------------------------------------------------------------ PART 1- GENERAL ----------------------------- 1.1
More informationSECTION RADIATION SHIELDING ENCLOSURE Low Intensity Radiation Protection
SECTION 13090 RADIATION SHIELDING ENCLOSURE Low Intensity Radiation Protection Prepared by: 90 Dayton Avenue, Unit 4B, Suite 13 Passaic, NJ 07055 (973) 574-9077 13090-1 LOW INTENSITY RADIATION PROTECTION
More informationNational Master Specification (NMS) Section Publisher: Spex.ca Page 1. Approved: RELATED REQUIREMENTS.1 Section [ ].
National Master Specification (NMS) Section 07 21 16 BLANKET INSULATION Publisher: Spex.ca Page 1 Approved: 2014-12-31 Part 1 General 1.1 RELATED REQUIREMENTS.1 Section [ ]. 1.2 REFERENCES.1 CSA Group.1
More informationMagnum Board Section Digicon Information Inc. Page 1
Digicon Information Inc. Page 1 This section includes water and mould resistant fibre-reinforced backer board for use under tile installations, suitable for use in wet areas. This section includes performance,
More informationESR-1812 Reissued October 1, 2012 This report is subject to renewal November 1, 2013.
ICC-ES Evaluation Report www.icc-es.org (800) 423-6587 (562) 699-0543 ESR-1812 Reissued October 1, 2012 This report is subject to renewal November 1, 2013. A Subsidiary of the International Code Council
More informationSECTION CORK-FACED ACOUSTICAL WALL PANELS. A. Class A cork-faced acoustical wall panels manufactured from recycled wood fiber material.
SECTION 09843 CORK-FACED ACOUSTICAL WALL PANELS PART 1 GENERAL 1.1 SECTION INCLUDES A. Class A cork-faced acoustical wall panels manufactured from recycled wood fiber material. B. Class B cork-faced acoustical
More informationArchitectural Roof and Wall Products Guide Specifications
Architectural Roof and Wall Products Guide Specifications Western States Metal Roofing 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 FORMED METAL WALL PANELS This Guide Specification
More informationSECTION GYPSUM WALLBOARD. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 092116 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationRAMAPO COLLEGE OF NEW JERSEY PHASE II HOUSING REHABILITATION C 2012
SECTION 09260 - GYPSUM BOARD ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION EXTERIOR GRILLS AND SCREENS
SECTION 10 82 13 PART 1 GENERAL PART 1 1 SUMMARY A. Section Includes: 1. Exterior perforated aluminum screen wall system with Ombrae TM Optical Tile imaging technology. 2. Accessories including attachments,
More informationSECTION NON-LOAD BEARING WALL FRAMING. B. Section Furring and Lathing: Lath and furring for interior plaster applications.
SECTION 09.22.16 NON-LOAD BEARING WALL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Non-load bearing metal studs for wall assemblies. B. Area Separation and shaft wall framing products. 1.2 RELATED SECTIONS
More informationINTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS UNIFORM EVALUATION SERVICES
1.0 INTRODUCTION INTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS UNIFORM EVALUATION SERVICES EVALUATION CRITERIA FOR COMPOSITE STEEL SHEET AND NONCOMBUSTIBLE SHEATHING PANELS EC 012-2016
More informationSPECIFICATION GUIDELINE
Environmental StoneWorks specification guideline should be used to assist design professionals in the preparation of projects. Edit and delete items that may not be applicable. Verify all referenced section
More informationCONSISTENT BUILD BISON STRONG LAFARGE GYPSUM IS NOW
LAFARGE GYPSUM IS NOW CONSISTENT BUILD BISON STRONG Count on Continental Building Products to deliver consistent, sustainable, high-quality drywall and finishing products alongside the responsive support
More informationSECTION GYPSUM BOARD
Manufacturer: American Gypsum 3811 Turtle Creek Blvd., Suite 1200 Dallas, Texas 75219 (800) 545-6302 (214) 530-5634 fax www.americangypsum.com GUIDE SPECIFICATION SECTION 09 29 00 This guide specification
More informationSPECIFICATION GUIDELINE
SPECIFICATION GUIDELINE Environmental Stoneworks Corporate Office 6300 East Stapleton Drive South Denver, CO 80216 Phone (303) 309-3040 Fax (303) 309-3059 www.estoneworks.com Environmental Stoneworks specification
More informationSECTION COLD-FORMED METAL TRUSSES
SECTION 054400 COLD-FORMED METAL TRUSSES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationPinkWood Ltd. Revised September 29, 2017
Fire-Rated Assemblies PR-S315 PinkWood Ltd. Revised September 29, 2017 Products: Series I-Joists PinkWood Ltd., 5929 6 th St. NE, Calgary, Alberta, Canada T2K 5R5 (403) 279-3700 www.pinkwood.ca 1. Basis
More informationSECTION PORTLAND CEMENT PLASTERING
SECTION 09 2400 PORTLAND CEMENT PLASTERING This section includes editing notes to assist the user in editing the section to suit project requirements. These notes are included as hidden text, and can be
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 092216 - COLD FORMED STEEL FRAMING - NON-STRUCTURAL (CFSF-NS) PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 ACTION
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09260 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY A. Provide gypsum board assemblies. 1.2 SUBMITTALS A. Product Data: Submit manufacturer's product data and installation instructions for
More informationMulti-Institutional Academic Health Science & Research Center Evansville, IN
SECTION 061600 - SHEATHING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationGYPSUM BOARD AND PLASTER
CHAPTER 25 SECTION 2501 GENERAL 2501.1 Scope. 2501.1.1 General. Provisions of this chapter shall govern the materials, design, construction and quality of gypsum board, lath, gypsum plaster and cement
More informationLouis Armstrong New Orleans International Airport NOAB Project # North Terminal Development Program Phase 1
Louis Armstrong New Orleans International Airport NOAB Project # 8910-01233 PART 1 - GENERAL SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS 1.1 RELATED DOCUMENTS A. Drawings and general provisions
More informationAugust, 2016 SECTION 09271
SECTION 09271 GYPSUM BOARD ** ACCESSORIES ** PART 1 - GENERAL 1.1 SUMMARY A. Related work specified elsewhere includes: 1. Rough carpentry. 2. Finish carpentry and millwork. 3. Metal support systems. 4.
More informationIce Rink Renovation & New Clubhouse
SECTION 092500 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationMAKING IT STICK: Nails and screws, adhesives and compounds... today contractors have a wide variety of choices.
MAKING IT STICK: Fasteners & Adhesives Walls hold up the building but what holds up the walls? Today contractors have a wide variety of fasteners and adhesives from which to choose, according to the needs
More informationDrywall and Plastering
Drywall and Plastering Drywall To order Drywall Joint Drywall Application 1 2 3 4 1. Cover joint or corner bead with mud coat 2. Embed paper joint tape into the mud. With fiberglass mesh tape you skip
More informationSECTION ROUGH CARPENTRY. B. AWPA (American Wood Preservers Association) Book of Standards. C. WCLIB (West Coast Lumber Inspection Bureau)
SECTION 06112 ROUGH CARPENTRY PART 1 GENERAL 1.01 REFERENCES A. APA (American Plywood Association) B. AWPA (American Wood Preservers Association) Book of Standards C. WCLIB (West Coast Lumber Inspection
More informationArchitectural Roof and Wall Products Guide Specifications
Architectural Roof and Wall Products Guide Specifications 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 FORMED METAL ROOF AND WALL PANELS This Guide Specification is to be used
More informationAND ACCESSORIES FOR DRYWALL CONSTRUCTION
STEEL TRIMS AND ACCESSORIES FOR DRYWALL CONSTRUCTION Quality in your corner. THE STRENGTH WITHIN MONTREAL TORONTO CALGARY EDMONTON VANCOUVER STEEL TRIMS AND ACCESSORIES for Construction BAILEY HAS YOUR
More informationDrywall and Plastering
Drywall and Plastering Drywall Drywall 120433 1 / 2 4 X 8 White Drywall Approx. 60/Lift None 120442 5 / 8 4 X 8 Firecode White Drywall Approx. 48/Lift None 120451 1 / 2 4 X 8 XP Drywall Approx. 48/Lift
More informationSECTION WOOD FRAMING. A. Includes But Not Limited To 1. Furnish and install wood framing and blocking as described in Contract Documents.
SECTION 06110 WOOD FRAMING PART 1 GENERAL 1.1 SUMMARY A. Includes But Not Limited To 1. Furnish and install wood framing and blocking as described in Contract Documents. B. Products Installed But Not Supplied
More informationSECTION SECURITY PROTECTION PART 1 GENERAL
SECTION 13 1010 - PART 1 GENERAL 1.01 SECTION INCLUDES A. Bullet Resistant Aluminum Windows. B. Bullet Resistant Transaction Equipment. C. Bullet Resistant Speakers. D. Bullet Resistant Glazing. E. Bullet
More informationDIVISION 5 METALS SECTION COLD-FORMED METAL FRAMING
DIVISION 5 METALS SECTION 05 40 00 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION GYPSUM BOARD SYSTEM
SECTION 09 29 00 GYPSUM BOARD SYSTEM PART 1 GENERAL 1.1 RELATED DOCUMENTS A. The provisions of the General Conditions, Supplementary Conditions, and the Sections included under Division 1, General Requirements,
More informationLamit Industries, Inc. 710 Marion Road Columbus, Ohio P-(614) F-(614)
Lamit Industries, Inc. 710 Marion Road Columbus, Ohio 43207 P-(614)444-3010 F-(614)444-4264 info@lamitindustries.com www.lamitindustries.com SECTION 06120 STRUCTURAL INSULATED PANELS PART 1 GENERAL 1.01
More informationSECTION METAL DOORS & FRAMES
SECTION 08-10-00 METAL DOORS & FRAMES Part 1 General 1.00 Scope of Work: Contractor shall provide labor and materials for a complete steel door install. 1.01 Section Includes A. Steel doors. B. Steel frames
More information