LATICRETE Family of Adhesives PRODUCT CATEGORY USE MIX WITH SUBSTRATE APPLICATION
|
|
- Britton Patterson
- 6 years ago
- Views:
Transcription
1 LATICRETE Family of Adhesives PRODUCT CATEGORY USE MIX WITH SUBSTRATE APPLICATION LATICRETE 4237 Latex Thin-Set Latex Thin-Set Additive 211 (118.4) Concrete Interior Mortar Additive Slurry Bond Coat* 272 (118.4) Cement Backer Board Exterior (D.S # 230.1) 317 (118.4) Swimming Pool Steam Room Facade LATICRETE 3701 Mortar Admix Latex Thin-Set Additive 272 (118.4) Concrete Interior (D.S ) 317 (118.4) Cement Backer Board Exterior 220 (118.4) Swimming Pool Steam Room Facade Mortar Bed* 226 or Wall Render 209 * bonded mud bed requires a slurry bond coat of LATICRETE 4237 Latex Thin-Set Mortar Additive and LATICRETE 211 Crete Filler Powder or LATICRETE 254 Platinum Multipurpose Thin-Set Mortar unbonded mud bed requires a cleavage membrane, wire-reinforcing, and minimum 2" thickness 1 of 10
2 LATICRETE Family of Adhesives LATICRETE 333 Super Flexible Additive Latex Thin-Set Additive 272 (118.4 & ) Concrete Interior (D.S ) 317 (118.4 & ) Cement Backer Board Exteriorª 220 (118.4 & ) Facade LATICRETE 101 Rapid-Set Latex Admix Latex Thin-Set Additive 272 (118.4 & ) Concrete Interior (D.S ) 317 (118.4 & ) Cement Backer Board Exterior 220 (118.4 & ) Swimming Pool Steam Room Facade Mortar Bed* * bonded mud bed requires a slurry bond coat of 4237/211 or 254 Platinum unbonded mud bed requires a cleavage membrane, wire-reinforcing, and minimum 2" thickness ª no standing water ˆ properly prepared - well bonded, clean and free of wax, oil, grease, dirt, dust, 2 or of any 10 other contaminant that can act as a bond breaker ˆˆ fully adhered, non-cushioned and properly prepared
3 LATICRETE Family of Adhesives LATICRETE 8510 Bonding Admix Acrylic Thin-Set Additive 272 (118.4) Concrete Interior (D.S ) 317 (118.4) Exterior 220 (118.4) Cement Backer Board Swimming Pool Facades Cement Terrrazzo Mortar Bed* 226 or Wall Render 209 LATICRETE 40 Multi-Use Acrylic Acrylic Thin-Set Additive 272 (118.4 & ) Concrete Interior (D.S ) 317 (118.4 & ) Cement Backer Board Exterior 220 (118.4 & ) Facades Mortar Bed* * bonded mud beds require a slurry bond coat of 4237/211 or 254 Platinum unbonded mud beds require a cleavage membrane, wire-reinforcing and minimum 2" of thickness mix 1 part 8510 with 2 parts clean water 3 of 10
4 LATICRETE Family of Adhesives LATICRETE 38 Acrylic Admix Acrylic Thin-Set Additive 272 (118.4) Concrete Interior (D.S ) 317 (118.4) Cement Backer Board Exterior 220 (118.4) Mortar Bed* LATICRETE 73 Crete Admix Latex Thin-Set Additive 211 (118.4) Concrete Interior (D.S ) 272 (118.4) Cement Backer Board Exterior 317 (118.4) Swimming Pool Steam Room Facade * bonded mud beds require a slurry bond coat of 4237/211 or 254 Platinum unbonded mud beds require a cleavage membrane, wire-reinforcing and minimum 2" of thickness 4 of 10
5 LATICRETE 254 Platinum Multipurpose Multipurpose LATICRETE Thin-Set Family of Adhesives Water (only) Concrete Interior Thin-Set Mortar Thin-Set (118.4 & ) Cement Backer Board Exterior (D.S ) Swimming Pool Steam Room Facade Gypsum Plaster LATICRETE 253 Gold Multipurpose Multipurpose Thin-Set Water (only) Concrete Interior Thin-Set Mortar Thin-Set (118.4 & ) Cement Backer Board Exterior (D.S ) Facade ˆ properly prepared - well bonded, clean and free of wax, oil, grease, dirt, dust, or any other contaminant that can act as a bond breaker ˆˆ fully adhered, non-cushioned and properly prepared 5 of 10
6 LATICRETE 253 Gold Rapid Multipurpose LATICRETE Thin-Set Family of Adhesives Water (only) Concrete Interior Multipurpose Thin-Set Mortar Thin-Set (118.4 & ) Cement Backer Board Exterior (D.S ) Facade LATICRETE 252 Silver Multipurpose Multipurpose Thin-Set Water (only) Concrete Interior Thin-Set Mortar Thin-Set (118.4 & ) Cement Backer Board Exterior (D.S ) Facade ˆ properly prepared - well bonded, clean and free of wax, oil, grease, dirt, dust, or any other contaminant that can act as a bond breaker ˆˆ fully adhered, non-cushioned and properly prepared 6 of 10
7 LATICRETE 255 MultiMax Thin-Set Multipurpose LATICRETE Thin-Set Family of Adhesives Water (only) Concrete Interior Mortar Thin-Set Medium Bed Mortar (118.4 & ) Cement Backer Board Exterior (D.S ) Facade Ceramic Tile LATICRETE 272 Premium Floor N' Wall Powder Thin-Set Water (118.1) Concrete Interior Thin-Set Mortar (D.S ) Latex (118.4) refer to specific latex Interior Exterior Swimming Pool Steam Room Facade LATICRETE 317 Floor N' Wall Thin-Set Powder Thin-Set Water (118.1) Concrete Interior Mortar (D.S ) Latex (118.4) refer to specific latex Interior Exterior Swimming Pool Steam Room Facade LATICRETE 211 Crete Filler Powder Powder Thin-Set 4237 or 73 (118.4) refer to 4237 or 73 Interior (D.S ) Exterior Swimming Pool Steam Room Facade when mixed with LATICRETE 3701 Mortar Admix or LATICRETE 4237 Latex Thin-Set Mortar Additive only 7 of 10
8 LATICRETE Family of Adhesives LATICRETE 220 Marble and Granite Powder Thin-Set Water (118.4) Concrete Interior Mortar Medium Bed Mortar Cement Backer Board Exterior (D.S ) Facade Latex (118.4) ¹ ² LATAPOXY 300 Epoxy Adhesive Epoxy Adhesive Pre-Packaged Concrete Interior (D.S ) Epoxy Cement Backer Board Exterior~ Components (118.3) Swimming Pool Steam Room Facade~ Epoxy Terrazzo Steel ¹ mix with LATICRETE 333 Super Flexible Additive ² mix with LATICRETE 3701 Mortar Admix ˆ properly prepared - well bonded, clean and free of wax, oil, grease, dirt, dust, or any other contaminant that can act as a bond breaker ˆˆ fully adhered, non-cushioned and properly prepared ~ contact LATICRETE Technical Services at x235 before recommending these installations 8 of 10
9 LATAPOXY 210 Modified Epoxy Epoxy LATICRETE Adhesive Family of Adhesives Pre-Packaged Concrete Interior Adhesive Grout Epoxy Cement Backer Board Exterior~ (D.S ) Components (118.8) Swimming Pool Steam Room Facade~ Steel LATAPOXY 310 Stone Adhesive Epoxy Spot Bond Adhesive Epoxy Components Concrete Interior (D.S ) Exterior Facades Cement Backer Board LATAPOXY 310 Rapid Stone Adhesive Epoxy Spot Bond Adhesive Epoxy Components Concrete Interior (D.S ) Exterior Facades Cement Backer Board ˆ properly prepared - well bonded, clean and free of wax, oil, grease, dirt, dust, or any other contaminant that can act as a bond breaker ˆˆ fully adhered, non-cushioned and properly prepared ~ contact LATICRETE Technical Services at x235 before recommending these installations exterior concrete must be 28 days old, 3,500 psi (24 Mpa) minimum compressive strength, 6" thick, reinforced, and a minimum of 28 days old exterior concrete masonry installations must be over double wythe construction with a 2" air gap between walls interior only maximum height restriction of 30', stone can be no more than 15 lbs. per square foot and no more than 720 square inches in facial dimension - check with local building code for actual code compliance 9 of 10
10 LATICRETE 15 Premium Multi-Mastic Organic LATICRETE Adhesive Family of Adhesives Pre-Mixed (136.1) Concrete Interiorº Adhesive Adhesive (Dry Areas Only) (D.S ) Cement Backer Board LATICRETE 9 Ceramic Tile Adhesive Organic Adhesive Pre-Mixed (136.1) Concrete Interiorº (D.S ) Adhesive (Dry Areas Only) Cement Backer Board ˆ properly prepared - well bonded, clean and free of wax, oil, grease, dirt, dust, or any other contaminant that can act as a bond breaker º interior use only - size limitations of: no larger than 10" x 10" ceramic tile or stone on vertical installations; no larger than 6" x 6" ceramic tile or stone on horizontal installations; and no larger than 2" x 2" on any porcelain tile installation All concrete surfaces must be free of curing compounds or concrete sealers, clean, free of dirt, dust, oil, wax, grease, paint, taping compound and any other material that can act as a bond breaker Cement backer board must be installed per board manufacturer's written installation instructions - check with board manufacturer for use of board in an exterior environment Please refer to LATICRETE TDS 152 for installation of tile or stone over wood floors For more specific information on each product please refer to listed data sheet (D.S.) - Data sheets are available at Technical Data Sheets are subject to change without notice. For latest revision, check our TDS 199.doc R 2/12/04 LATICRETE, LATAPOXY and the logo are Registered Trademarks of LATICRETE International, Inc. TDS 199.doc R 2 December of 10
CONCRETE STAIRS Note:
With the increased use of concrete tile and stone over the past decade, there has been an increase in demand for installing concrete tile or stone on stairs. Historically, these types of installations
More informationSECTION LATEX-MODIFIED MEDIUM BED MORTAR
SECTION 09305.24 LATEX-MODIFIED MEDIUM BED MORTAR This product guide specification can be used to specify Hydroment Big Tile & Stone Mortar, a latex-modified, medium bed mortar designed for setting large
More informationFiber Reinforced Tile and Stone Mortar
, ANSI A 118.4, ANSI A 118.11 ARDEX X 77 MICROTEC Fiber Reinforced Tile and Stone Mortar The most advanced technology ideal for large format porcelain tile installations,exterior or interior, floor or
More informationARDEX X 32 MICROTEC Universal Rapid Setting and Drying Thin-to-Thick Bed Mortar
ANSI A 118.15, ANSI A 118.4, ANSI A 118.11 ARDEX X 32 MICROTEC Universal Rapid Setting and Drying Thin-to-Thick Bed Mortar The fast track, interior or exterior, thin-to-thick bed solution for every natural
More informationInstallation of Ceramic Tile in Swimming Pools
Installation of Ceramic Tile in Swimming Pools TDS 192 DESIGN CONSIDERATIONS I. Primary types of swimming pool structures A. Cast-in-place reinforced concrete 1. Definition concrete placed or pumped on-site
More informationKolorines Glass Mosaic Tiles Project Specification
Kolorines Glass Mosaic Tiles Project Specification SUGGESTED SPECIFICATION Glass Mosaic Tile Installation for Swimming Pools NOTES TO SPECIFIER: 1. Specify PremiumPlus Thin-Set mixed with CustomFlex Additive
More informationARDEX X 90 OUTDOOR TM
ANSI A 118.15, ANSI A 118.4, ANSI A 118.11 ARDEX X 90 OUTDOOR TM MicroteC3 Rapid-Set, Flexible Tile and Stone Mortar Maximum weatherproof protection against the harshest elements for outdoor tile and stone
More informationFinish Flooring- Hard Flooring Materials
Finish Flooring- Hard Flooring Materials The most desirable types of flooring by designers and building owners Types of Hard Flooring Materials Concrete Stone Ceramic Tiles Quarry Tiles Bricks and Brick
More informationLATICRETE 252 Ag SILVER Thin-set Adhesive
LATICRETE 252 Ag SILVER Thin-set Adhesive Bonds to various substrates Exceeds ANSI A118.4 shear bond strength requirements Complies to EN with a C2 E T classification Water and shock resistant. Suitable
More informationRapid-Set, Rapid-Dry, Super-Format Tile and Uncoupling Membrane Mortar
ARDEX S 28TM MICROTEC Rapid-Set, Rapid-Dry, Super-Format Tile and Uncoupling Membrane Mortar Unmatched performance and protection for super-format tile and uncoupling membrane installations! Rapid-drying
More informationLATAPOXY 310 Stone Adhesive
LATAPOXY 310 Stone Adhesive PRODUCT DESCRIPTION LATAPOXY 310 Stone Adhesive is a two component, high strength epoxy adhesive, which is formulated for the spot bonding method of tile and stone installations
More informationSuitable Substrates PRODUCT DESCRIPTION. Packaging 5 kg & 20 kg bags. Colour: Grey and white. Application. Coverage. Shelf Life.
LATICRETE 252 Ag SILVER Thin-set Adhesive Exceeds ANSI A118.4 shear bond strength requirements Complies to EN with a C2 E T classification Water and shock resistant. Suitable Substrates Concrete Cement
More informationSubmittal Packages Detailed with Items and Reviewers
Submittal Packages Detailed with Items and Reviewers Tenochca Upgrades Project # 2351 San Diego State University 5500 Campanile Drive San Diego, CA 92182 Tel: 619-594-3740 Fax: 0062-093000-0 Tiling - Thin-Set
More informationRe-Grouting Floor Joints in Commercial Kitchens and Industrial Applications
Re-Grouting Floor Joints in Commercial Kitchens and Industrial Applications GENERAL CONDITIONS Degradation or deterioration of an epoxy grout can occur when the circumstances are right or when the wrong
More informationCDK Neolith Reduced Thickness Porcelain Panel Installation Specification.
CDK Neolith Reduced Thickness Porcelain Panel Installation Specification. This specification covers the installation of Neolith Reduced Thickness Porcelain Panel to concrete or other suitable masonry substrates.
More informationHYDRO BAN Quick Cure Waterproofing Membrane
HYDRO BAN Quick Cure Waterproofing Membrane DS-670.4-0718 1. PRODUCT NAME HYDRO BAN Quick Cure Waterproofing Membrane 2. MANUFACTURER LATICRETE International, Inc. 1 LATICRETE Park North Bethany, CT 06524-3423
More informationSECTION TILING
PART 1 GENERAL 1.01 SECTION INCLUDES A. Ceramic Tile for floor applications. B. Ceramic Tile for wall applications. C. Ceramic accessories. D. Ceramic trim. E. Non-ceramic trim. 1.02 RELATED REQUIREMENTS
More informationHYDRO BAN. Installation instructions for Australia TDS-1003 SUITABLE SUBSTRATES SUBSTRATE CONDITIONS
HYDRO BAN Installation instructions for Australia TDS-1003 All waterproofing work for Domestic Wet Areas in Australia shall conform to AS3740-2010 & AS4858. All waterproofing work for External Above Ground
More informationNXT SUBSTRATE PREPARATION AND PRIMER GUIDE TDS 230N
NXT SUBSTRATE PREPARATION AND PRIMER GUIDE TDS 230N Substrate preparation is the most important factor to successful NXT self-leveling underlayment (SLU) and NXT Vapor Reduction Coating installations.
More informationEzarri JointPoint Glass Mosaic Tile Installation in Immersed Installations. 10 Year System Warranty.
Ezarri JointPoint Glass Mosaic Tile Installation in Immersed Installations. 10 Year System Warranty. This specification covers the installation of Ezarri JointPoint Glass Mosaic tiles inside a concrete
More informationInstallation of Large Format Tile & Stone
Installation of Large Format Tile & Stone TDS 193 Use of Large Format Tile and Stone Twenty to twenty five years ago choosing tile was simple. Floor tile was typically 8 x 8 (200mm x 200mm) and wall tile
More informationARDEX STONE VENEER INSTALLATION MATERIALS AND SYSTEMS
ARDEX GUIDE SPECIFICATION ARDEX AM 100 TM, ARDEX 8+9, ARDEX X77 TM, ARDEX X5 TM, and ARDEX FH TM Substrate Preparation Materials for Interior Applications to Receive the Installation of Tile and Stone
More informationSECTION TILING
SECTION 09 30 00 TILING PART 1 - GENERAL 1.1 SUMMARY A. Section includes tile as indicated on new surfaces and as specified. 1.2 SUBMITTALS A. Samples: 1. Submit samples of colors and sizes of tile. B.
More informationINSTALLATION SYSTEMS FOR FLOORING PROFESSIONALS. High-quality products Progressive ideas Great service
INSTALLATION SYSTEMS FOR FLOORING PROFESSIONALS High-quality products Progressive ideas Great service ADVANCEMENT THROUGH INNOVATION Chembond holds to this fundamental philosophy to meet the demands of
More informationLATICRETE products may help contribute to the following LEED v4 Credits (unless otherwise noted);
produces an assortment of portland cement and epoxy based setting and grouting materials. The LEED Projects program is gaining more popularity with architectural firms and building design groups. The following
More informationTECHNICAL DATA SHEET AUS-CRETE PREMIUM INDUSTRIAL
SUITABLE FOR HEAVY TRAFFIC, SWIMMING POOLS, TILE AND STONE FACADES INDUSTRIAL GRADE ADHESIVE EXTRA HEAVY DUTY SHOCK AND VIBRATION RESISTANT SUITABLE FOR: EXTRA LARGE TILE AND STONE ALL MASONRY SUBSTRATES
More informationA. Description of Work: Work of this section includes self leveling underlayment for interior finish flooring but is not limited to, the following:
SECTION 03540 [03 54 13] Floor Underlayment PART 1 - GENERAL ***Notes to Architect are highlighted in red**** 1.01 SUMMARY A. Description of Work: Work of this section includes self leveling underlayment
More informationTechnical Bulletin. CTIOA Technical Committee
CTIOA Technical Committee Technical Bulletin Technical Bulletin No. 2010-3-23 Revision 0 March 23, 2010 Scale: None Page 1 of 7 Tile Exterior Veneer Lath, Scratch, Brown Coat Tensile and Shear Bond Strength
More informationSECTION COMMON WORK RESULTS FOR CONCRETE SSPECIALTY COATINGS
SECTION 03 05 00 COMMON WORK RESULTS FOR CONCRETE 09 97 00 SSPECIALTY COATINGS Weld Crete ************************************************************************************************************************
More informationNew Veneers Allow Greater Flexibility
New Veneers Allow Greater Flexibility A number of new veneer systems are being used with exterior insulation or standard insulation batts to create panels that are easily applied, provide outstanding insulation
More informationGeneral Glass Mosaic Tile Fixing Specification for Immersed Installations.
General Glass Mosaic Tile Fixing Specification for Immersed Installations. This specification covers the installation of dot mounted glass mosaic inside of, and around concrete Swimming Pools. Refer to
More informationLATICRETE Substrate Preparation and Primer Guide for Self-Levelling Underlayments
LATICRETE Substrate Preparation and Primer Guide for Self-Levelling Underlayments TDS-1230 Substrate preparation is the most important factor for a successful LATICRETE self-levelling underlayment (SLU)
More informationARDEX GUIDE SPECIFICATION ARDEX K 60 ARDITEX A Rapid Setting Latex Smoothing and Leveling Compound
ARDEX GUIDE SPECIFICATION ARDEX K 60 ARDITEX A Rapid Setting Latex Smoothing and Leveling Compound SECTION 03 54 16 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract,
More informationEzarri JointPoint Glass Mosaic Tile Installation in Immersed Installations. 10 Year System Warranty.
Ezarri JointPoint Glass Mosaic Tile Installation in Immersed Installations. 10 Year System Warranty. This specification covers the installation of Ezarri JointPoint Glass Mosaic tiles inside of, and around
More informationDrytek 7400 DS FEATURES/BENEFITS USES MANUFACTURER STANDARDS/CERTIFICATIONS
Globally Proven Construction Solutions Drytek 7400 DS77-7400 -0117 DRYTEK 7400 is a superior quality, fast drying, dual purpose self-leveling overlayment / interior wear surface topping that can be accented
More informationTECHNICAL DATA SHEET AUS-BOND INDUSTRIAL LATEX ADMIX
Description: Aus-Bond Industrial Latex Admix is a specially formulated latex admix for use in sand/cement based mortars for extreme conditions such as swimming pools, facades, rapid transit stations and
More informationSingle Source Comprehensive Warranty. ARDEX Americas. Swimming Pool Guide
Single Source Comprehensive Warranty ARDEX Americas Swimming Pool Guide The ARDEX Pool System Wall Preparation WALLS SMOOTHING AND REPAIR ARDEX AM 100 TM Rapid Set Pre-Tile Smoothing and Ramping Mortar
More informationInterior Finish Materials
Ceramic Tile Ceramic tiles are relatively small, modular surfacing units made of clay or other ceramic material The tiles are fired in a kiln at very high temperatures The result is a durable, dense material
More informationHYDRO BARRIER DS PRODUCT NAME HYDRO BARRIER
HYDRO BARRIER DS-105.0-0517 Fast curing; allows foot traffic in 4 6 hours @ 70 F (21 C), 50% RH Lighter color for ease of inspection Safe no solvents and non-flammable Install tile, brick and stone directly
More informationSECTION CEMENT BOARD SUPPORTED ADHERED MASONRY VENEER. 2. Installation materials including adhesives, mortars, and pointing mortars.
(Specifier Note: The purpose of this guide specification is to assist the Specifier in correctly specifying cement board supported adhered masonry. The Specifier needs to edit these guide specifications
More informationLATICRETE products may help contribute to the following LEED v4 Credits (unless otherwise noted);
produces an assortment of portland cement and epoxy based setting and grouting materials. The LEED Projects program is gaining more popularity with architectural firms and building design groups. The following
More informationNATURAL STONE SLIMLITE SLATE & QUARTZITE
Cover photo features SlimLite Copper quartzite on the fireplace. Above photo features SlimLite Autumn Mist slate on the wall. Harmonizing Innovation with the Timeless Beauty of Stone For thousands of years,
More information22/04/2013. How can you select the right product for the right job? Tile installation products that best fit the application?
Tile installation products that best fit the application? How can you select the right product for the right job? How can you select the right product for the right job? By choosing the installation products
More informationARDEX A 38 MIX Rapid Set, Premixed Screed
TM ARDEX A 38 MIX Rapid Set, Premixed Screed Fast-setting, premixed, easy-to-use and high-performance screed Note: The data herein applies to the ARDEX A 38 MIX 40 lb. (18 kg) bag which is pre-mixed with
More informationBush Elem. Addition & Alterations QUARRY TILE SECTION QUARRY TILE PART 1 - GENERAL
73651.01 QUARRY TILE 093016-1 1.1 RELATED DOCUMENTS: SECTION 093016 - QUARRY TILE PART 1 - GENERAL A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division
More informationI. SUBSTRATE TYPES/GENERAL REQUIREMENTS
Substrate preparation is the most important factor to a successful DRYTEK self-leveling underlayment (SLU), Moisture Vapor Barrier or decorative wear surface installation. While it is not possible to cover
More informationDrying of Concrete TDS 183
Drying of Concrete TDS 183 As the occurrence of fast track construction continues to rise, the need to install a finished floor on a wet concrete slab is typically far too soon for the floor covering.
More information/ARD BuyLine 8656 ARDEX TILE & STONE INSTALLATION PRODUCT SHOWCASE
09 30 00.11/ARD BuyLine 8656 2009 ARDEX TILE & STONE INSTALLATION PRODUCT SHOWCASE The ARDEX Tile & Stone Installation System is a full line of thin set mortars, tile adhesives, waterproofing systems,
More informationARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment
ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,
More informationTECHNICAL DATA SHEET AUS-FLEX GOOD as GOLD LIGHT
POLYMER AND RUBBER FORTIFIED FLEXIBLE, LIGHTWEIGHT MULTI-PURPOSE ADHESIVE SUITABLE FOR: PORCELAIN TILE ALL MASONRY SURFACES CERAMIC TILE CONCRETE QUARRY TILE RENDER, BRICK AND BLOCK WORK MOSAIC TILE AND
More informationARDEX A 38TM Rapid Set Screed
ARDEX A 38TM Rapid Set Screed Fast-setting, easy-to-use, high-performance screed Note: The data herein applies to ARDEX A 38 50 lb. bag, not pre-mixed with sand. For ARDEX A 38 MIX 40 lb. bag that is premixed
More informationRLA CERAMIC TILE ADHESIVE 10 year Limited Warranty
RLA CERAMIC TILE ADHESIVE 10 year Limited Warranty RLA Polymers Pty Ltd; undertakes to warranty Resinflex (or RLA Flex 2- Part), and RLA Flex 1-Part, when used to install tiles over Protectowrap AFM for
More informationE.MIX MOISTURE SEALER
E.MIX Super Fast Fix Fast setting, high performance, high strength, highly flexible, strong polymerized thin bed tile adhesive for interior and exterior wall tile fixing complied with C2FTE class of EN
More informationProducts for the Tiling Industry
s for the Tiling Industry Preparation Screedmaster Universal Primer Screedmaster Epoxy Primer Screedmaster Flex Screedmaster Deep Screedmaster Universal Primer is a water based solvent free, acrylic dispersion
More informationSECTION CEMENT BOARD SUPPORTED ADHERED MASONRY VENEER Propriety Specification for National Gypsum PermaBase Cement Board and LATICRETE MVIS
(Specifier Note: The purpose of this guide specification is to assist the Specifier in correctly specifying cement board supported adhered masonry. The Specifier needs to edit these guide specifications
More informationTECHNICAL DATA SHEET AUS-FLEX MULTI-LIGHT 9.5
FLEXIBLE, LIGHTWEIGHT TILE AND STONE ADHESIVE POLYMER AND RUBBER REINFORCED FOR WALLS AND FLOORS INTERNAL AND EXTERNAL USE SUITABLE FOR: PORCELAIN TILE ALL MASONRY SURFACES CERAMIC TILE CONCRETE QUARRY
More informationPVT Masonry Veneer Mortar HB
PVT Masonry Veneer Mortar HB 1. PRODUCT NAME ProSpec PVT Masonry Veneer Mortar HB 2. MANUFACTURER Akona Manufacturing, LLC, a TCC Materials company (Akona Manufacturing is a licensed manufacturer of ProSpec
More informationB. Related Sections: 1. Division 07 Section "Joint Sealants" for sealing of expansion, contraction, control, and isolation joints in tile surfaces.
SECTION 093000 - CERAMIC TILE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationPRODUCT DESCRIPTION FLOOR AND WALL THIN SET ADHESIVE
NSA PRO++ POLYMER MODIFIED CEMENT BASE ADHESIVE PRODUCT DESCRIPTION FLOOR AND WALL THIN SET ADHESIVE NSA PRO++ is a smooth and creamy thin set adhesive for installing small to medium format ceramic les,
More informationSTEAM SHOWER / ROOM; WOOD OR METAL STUDS Wood or Metal Studs Cement Backer Board Walls, Mortar Bed Floor Ceramic Tile
STEAM SHOWER / ROOM; WOOD OR METAL STUDS Wood or Metal Studs Cement Backer Board Walls, Mortar Bed Floor Ceramic Tile MAPEI: MSR614 TCNA: SR614-13 TTMAC: 321SR-B SLOPED CEILING 2" (50 mm) PER FOOT CEMENT
More informationCUSTOM BRICK. Custom Brick Finish Polymer System Specifications For Use On Vertical Walls DS151. Architectural Finish for Use on Vertical Walls
CUSTOM BRICK Architectural Finish for Use on Vertical Walls Custom Brick Finish Polymer System Specifications For Use On Vertical Walls PART I- GENERAL DRYVIT SYSTEMS, INC. MANUFACTURER S SPECIFICATION
More informationARDEX GUIDE SPECIFICATION ARDEX K 22 F High Flow, Fiber Reinforced, Self-Leveling Underlayment
ARDEX GUIDE SPECIFICATION ARDEX K 22 F High Flow, Fiber Reinforced, Self-Leveling Underlayment SECTION 03 54 13 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract, and
More informationSECTION GUIDE SPECIFICATION FOR ARDEX TILE & STONE INSTALLATION MATERIALS AND SYSTEMS
PART 1 - GENERAL SECTION 09 30 00 GUIDE SPECIFICATION FOR ARDEX TILE & STONE INSTALLATION MATERIALS AND SYSTEMS 1.0.1 SUMMARY A. Work performed under the requirements of this section shall be subject to
More informationCUSTOM BRICK. Custom Brick Finish Polymer System Specifications For Use On Vertical Walls DS151. Architectural Finish for Use on Vertical Walls
CUSTOM BRICK Architectural Finish for Use on Vertical Walls Custom Brick Finish Polymer System Specifications For Use On Vertical Walls PART I- GENERAL DRYVIT SYSTEMS, INC. MANUFACTURER S SPECIFICATION
More informationSECTION ARDEX TILE AND STONE INSTALLATION MATERIALS AND SYSTEMS
ARDEX GUIDE SPECIFICATION ARDEX DS70 TM Acoustic Mat and ARDEX 8+9 TM Rapid Waterproofing and Crack Isolation Compound Subfloor Preparation Materials for Sound Deadening Applications to Receive the Installation
More informationARDEX GUIDE SPECIFICATION ARDEX SD-M Designer Floor Finish
ARDEX GUIDE SPECIFICATION ARDEX SD-M Designer Floor Finish SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract,
More informationLATICRETE and Moisture Vapour Emission Rate, Relative Humidity and Moisture Testing of Concrete
LATICRETE and Moisture Vapour Emission Rate, Relative Humidity and Moisture Testing of Concrete TDS-1166 Materials used in tile and stone installation applications can be affected by moisture during the
More informationDynamic Coatings Inc. (877) Premium Self-Leveling Underlayment
Dynamic Coatings Inc. (877) 225-2549 www.dciflooring.com ARDEX K 15 Premium Self-Leveling Underlayment Portland cement-based Use to level and smooth interior concrete, terrazzo, ceramic and quarry tile,
More informationSPECIFICATIONS ADVANTAGES. For more information on this product or to order samples call or visit our website at builddirect.
Insulayment is a unique, earth-friendly, insulating underlayment that helps absorb impact sound so it won t transfer to lower level rooms; suppresses the effect of concrete sub-floor cracking to protect
More informationLATICRETE HYDROBAN Waterproof Membrane
Technical Data Sheet LATICRETE HYDROBAN Waterproof Membrane LATICRETE Hydro Ban is a single component, self curing liquid rubber polymer that forms a flexible, thin, seamless, load bearing under tile Waterproofing/crack
More informationHYDRO BAN DS PRODUCT NAME HYDRO BAN
HYDRO BAN DS-663.0-0914 1. PRODUCT NAME HYDRO BAN 2. MANUFACTURER LATICRETE International, Inc. 1 LATICRETE Park North Bethany, CT 06524-3423 USA Telephone: +1.203.393.0010, ext. 235 Fax: +1.203.393.1684
More informationDrytek 4000 FEATURES/BENEFITS USES MANUFACTURER STANDARDS/CERTIFICATIONS
Drytek 4000 Globally Proven Construction Solutions FEATURES/BENEFITS Pourable and pumpable Inorganic; will not contribute to mold/mildew growth Suitable surface for most finished floor goods Can be applied
More informationWEIGHT PER PIECE (LBS.)
PRODUCT DESCRIPTION DATA SHEET 04 73 19-US BASIC USE ProGUARD DP is intended to be installed over sheathing and waterproofing over steel or wood studs or over concrete masonry units or poured concrete
More information(1:4) Heavy Duty, (1:9) ph Balancing (1:20) All Purpose Cleaner. (Power Cleaner: Water) Quart, 1 Gallon, 5 Gallon Pail, 55 Gallon Drum
POWER CLEANER Power Cleaner is a highly concentrated, commercial strength cleaner, degreaser, and wax remover for commercial and industrial use. Power Cleaner has been formulated with a distinct blend
More informationDYNAFLEX 600. Tile & Stone POLYMER-MODIFIED THIN-SET MORTAR
Tile & Stone DYNAFLEX 600 PREMIUM GRADE Description The ultimate one-step, polymer modified, thin-set mortar for interior and exterior installation of ceramic tile, porcelain stoneware, natural stone,
More information1.3 Work shall include all reinforcement and accessories necessary to complete installation.
CERAMIC TILING GENERAL INFORMATION 1.1 Ceramic mosaic tile floors and bases, glazed wall tile wainscots and walls, and marble thresholds. 1.2 Installation will typically be with latex-portland cement mortar
More informationSECTION HYDRAULIC CEMENT UNDERLAYMENT
ARDEX GUIDE SPECIFICATION ARDEX V 1200 Self-Leveling Underlayment A Self-Leveling Underlayment that Consists of a Blend of Portland Cements, Other Hydraulic Cements and Polymers for Interior Applications
More informationINTERIOR WALLS OVER SOLID BACKING
INTERIOR WALLS OVER SOLID BACKING Mortar Bed (One-Coat Method) Stone Tile MAPEI: MW222-Stone TCNA: W222-15-Stone TTMAC: N/A Version: 2015 SOLID BACKING: WOOD, PLASTER, MASONRY, OR GYPSUM BOARD STONE TILE
More informationMay 2, 2018, Bethany, Conn. -- LATICRETE, a leading manufacturer of globally proven construction solutions for
Media Contact: Alexandra Ruffo, (214) 329-9191 alexandra@coopersmithagency.com LATICRETE Moves Industry Forward with New Product Offerings Showcased at Coverings 2018 Innovative product solutions include
More informationXTREME-BOND INSTALLATION SYSTEM
XTREME-BOND FOR THIN-STONE VENEER Weather-resistant resistant Superior bonding & flexural strengths Exceptional sag resistance Meets requirements of Type S mortar Pre-blended for quality consistency from
More informationSECTION HYDRAULIC CEMENT UNDERLAYMENT
ARDEX GUIDE SPECIFICATION ARDEX K 15 Premium Self-Leveling Underlayment A Self-Leveling Underlayment that Consists of a Blend of Portland Cements and Other Hydraulic Cements for Interior Applications SECTION
More informationfor the master tradesman Setcrete Product Guide
Professional Flooring products for the master tradesman Setcrete Product Guide Professional flooring products for the master tradesman Floor Levelling Compounds SETCRETE Floor Levelling Product Selector
More informationCHAPTER 10: Finishes CONTENTS 10.1 PLASTERWORK 10.2 SECOND AND THIRD FIX FINISHES. Chapter 10
CONTENTS 10.1 PLASTERWORK 10.2 SECOND AND THIRD FIX FINISHES 283 Chapter 10 FUNCTIONAL REQUIREMENTS FUNCTIONAL REQUIREMENTS 10.1 PLASTERWORK Workmanship i. All workmanship must be within the tolerances
More informationARDEX GUIDE SPECIFICATION ARDEX TRM Transportation Repair Mortar Fast-Setting Concrete Repair Mortar
ARDEX GUIDE SPECIFICATION ARDEX TRM Transportation Repair Mortar Fast-Setting Concrete Repair Mortar SECTION 03 92 50 PART 1 - GENERAL 1.1 SUMMARY A. This section includes Portland cement-based, microsilica-modified,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TABLE OF CONTENTS Warranty... 2 Intro... 3 Laying Nuheat Membrane... 4 5 Laying the Tiles.... 6 Waterproofing... 7 Installing on Different Substrates Wood Structure... 8 9 Cement
More informationTILING SPECIFICATIONS
TILING SPECIFICATIONS SPECIFICATION NUMBER: NR204-16 PREPARED BY: Mike Cubley PREPARED FOR: Porcelain Plus ATTENTION: Kirk Pollock INSTALLATION: 712 Turner Floor and Wall Tiling Specification. M40 STONE/
More informationARDEX UI 740 FLEXBONE Uncoupling Membrane
ARDEX UI 740 FLEXBONE Uncoupling Membrane FLEXBONE - The most advanced single source uncoupling solutions! High load-bearing uncoupling membrane Ideal for large format tile and stone in heavy traffic areas
More informationCHAPTER 10: Finishes CONTENTS 10.1 PLASTERWORK ND AND 3 RD FIX FINISHES
CONTENTS 10.1 PLASTERWORK 10.2 2 ND AND 3 RD FIX FINISHES FUNCTIONAL REQUIREMENT 10.1 Plasterwork Workmanship Design Technical Manual TS-011-09-010412 i. All workmanship must be within defined tolerances
More informationThin-Set Troubleshooting Guide for Concrete and Masonry Substrates
Thin-Set Troubleshooting Guide for Concrete and Masonry Substrates Complaint Cause(s) Prevention Cracked Tiles or Grout Loose Tile 1. Deflection of suspended slab 2. Hair-line or spider cracks in 3. Lack
More informationSECTION CONCRETE PAVING SLABS SET IN MORTAR
SECTION 32 14 13.16 CONCRETE PAVING SLABS SET IN MORTAR (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs mortared to a concrete base and grouted joints
More informationLAYOUT CONSIDERATIONS
1-800-447-2838 Installation Instructions Vanishing Lid System Layout Cover-Pools Vanishing Lid design is an adjustable, tray-support system for any kind or style of deck material you prefer to use for
More informationSECTION MORTAR-BED STONE TILING [Interior Applications] [SECTION ]
(Specifier Note: The purpose of this guide specification is to assist the specifier in correctly specifying Porphyry Stone Pavers. The specifier needs to edit these guide specifications to fit the needs
More informationSECTION CERAMIC/PORCELAIN TILING
SECTION 09 30 13 CERAMIC/PORCELAIN TILING SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable in the section and renumber the
More informationSelecting and Specifying Ceramic Tile with ANSI and ISO Standards
Selecting and Specifying Ceramic Tile with ANSI and ISO Standards Learning Objectives Review Industry Standards and Resources ANSI - American National Standards Institute ISO International Standards Organization
More informationShower Waterproofing Membrane Under tile and wet area waterproofing membrane.
Product Information Technical Data Sheet - December 2017 Shower Waterproofing Membrane Under tile and wet area waterproofing membrane. DESCRIPTION Crommelin Shower Waterproofing Membrane is a waterbased,
More informationFLUID APPLIED WATERPROOFING
SECTION 07120 FLUID APPLIED WATERPROOFING PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 09200 - Metal Studs, Metal Lath, Suspension Ceilings, Plaster, and Stucco.
More informationARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment
ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,
More informationSECTION QUARTZ SURFACING COUNTERTOPS
SECTION 12 3661.19 QUARTZ SURFACING COUNTERTOPS This section includes editing notes to assist the user in editing the section to suit project requirements. These notes are included as hidden text, and
More informationCTIOA REPORT
CERAMIC TILE INSTITUTE OF AMERICA, INC. 12061 Jefferson Blvd., Culver City, CA 90230-6219 CTIOA REPORT 2007-4-1 SUBJECT: STONE TILE By: CTIOA Specialty Tile Products Committee: Description Modular stone
More informationINSTALLATION OF CERAMIC TILE IN SWIMMING POOLS INSTALLATION OF CERAMIC TILE IN SWIMMING POOLS
INSTALLATION OF CERAMIC TILE IN SWIMMING POOLS INSTALLATION OF CERAMIC TILE IN SWIMMING POOLS Richard P. Goldberg, Architect AIA, CSI Professional Consultants International Outline of Presentation
More information